HMC602LP4E - Hittite Microwave Corp.

POWER DETECTORS - SMT

8 - 22

For price, delivery, and to place orders, please contact Hittite Microwave Corporation:

20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373

Order On-line at www.hittite.com

HMC602LP4 / 602LP4E

General Description

Features

Functional Diagram

The HMC602LP4(E) Logarithmic Detector/Controller

converts RF signals at its input, to a proportional DC

voltage at its output. The HMC602LP4(E) employs

a successive compression topology which delivers

extremely high dynamic range and conversion accuracy

over a wide input frequency range. As the input power

is increased, successive ampli ers move into saturation

one by one creating an accurate approximation of the

logarithm function. The output of a series of square law

detectors is summed, converted into voltage domain

and buffered to drive the LOGOUT output. For detection

mode, the LOGOUT pin is shorted to the VSET input,

and will provide a nominal logarithmic slope of -25mV/

dB and an intercept of 12 dBm (19 dBm for ƒ ≥ 5.8 GHz).

The HMC602LP4(E) can also be used in the controller

mode where an external voltage is applied to the VSET

pin, to create an AGC or APC feedback loop.

Wide Dynamic Range: up to 70 dB

High Accuracy: ±1 dB with 60 dB Range Up To 6 GHz

Fast: 8ns Output Response Time

Supply Voltage: +5V

Power-Down Mode

Excellent Stability over Temperature

Buffered Temperature Sensor Output

Compact 4x4mm Leadless SMT Package

Typical Applications

The HMC602LP4(E) is ideal for IF and RF applica-

tions in:

• Cellular/PCS/3G

• WiMAX, WiBro, WLAN, Fixed Wireless & Radar

• Power Monitoring & Control Circuitry

• Receiver Signal Strength Indication (RSSI)

• Automatic Gain & Power Control

Electrical Specifications, TA = +25C, EN= 5V, Vcc1, Vcc2, Vcc3= +5V [1]

Parameter Typ. Typ. Typ. Typ. Typ. Typ. Typ. Typ. Typ. Typ. Units

Input Frequency 50 100 900 1900 2200 3600 5800 7000 7500 8000 MHz

±3 dB Dynamic Range 70 70 72 71 72 70 66 62 59 57 dB

±3 dB Dynamic Range Center -30 -30 -30.5 -32.5 -33 -31 -25 -22 -22 -20.5 dBm

±1 dB Dynamic Range 61 61 63 63 62 57 60 55 50 46 dB

Output Slope -25.7 -25.7 -25.3 -25.0 -24.9 -24.8 -25.5 -27.5 -28.9 -30.2 mV/dB

Out put Intercept +13.2 +13.2 +13.4 +13.0 +12.4 +14. 2 +21.3 +20. 2 +19. 2 +18 .5 dBm

Temperature Sensitivity @ -10 dBm Input [2] 12 .3 11.2 11.4 11.6 12.5 14.7 16.9 24.6 27.7 33.0 m dB/ °C

[1] Detector mode measurements; LOGOUT (Pin 15) is shorted to VSET (Pin 16).

[2] Measured from TA = -40C to TA = +85C

70 dB, LOGARITHMIC

DETECTOR / CONTROLLER, 1 - 8000 MHz

v01.0407

POWER DETECTORS - SMT

8 - 23

For price, delivery, and to place orders, please contact Hittite Microwave Corporation:

20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373

Order On-line at www.hittite.com

Electrical Specifications, (continued)

Parameter Conditions Min. Typ. Max. Units

LOGOUT Interface

Output Voltage Range 0Vcc -1.0V

Output Rise Time/Fall Time From 0% to 90% 7.5 / 8.1 ns

VSET Interface

Input Impedance 30 kΩ

Input Voltage Range 0.25 to 1.35 V

Low Frequency Gain VSET to LOGOUT 56 dB

Open Loop Corner Frequency 700 kHz

Power Down (EN) Interface

Voltage Range for Normal Mode 0.8 x Vcc [1] Vcc [1] V

Voltage Range for Powerdown Mode 0 0.2 x Vcc [1] V

Threshold Voltage Vcc [1]/2 V

Power Supply (Vcc1, Vcc2, Vcc3)

Operating Voltage Range 4.5 5.5 V

Supply Current in Normal Mode 113 mA

Supply Current in Power Down Mode 1mA

[1] Vcc= Vcc1= Vcc2= Vcc3= +5V

HMC602LP4 / 602LP4E

Parameter Condition

Vcc1, Vcc2, Vcc3 +5V

Input Zo - w/ 68Ω Term Resistor at INP 50Ω

TA+25C

Fin 900 MHz

INN Port connected to ground through a 1000pF capacitor

Test Conditions

v01.0407 70 dB, LOGARITHMIC

DETECTOR / CONTROLLER, 1 - 8000 MHz

POWER DETECTORS - SMT

8 - 24

For price, delivery, and to place orders, please contact Hittite Microwave Corporation:

20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373

Order On-line at www.hittite.com

LOGOUT Voltage & Error

vs. Input Power, Fin = 100 MHz

LOGOUT Voltage & Error

vs. Input Power, Fin = 2200 MHz

LOGOUT Voltage & Error

vs. Input Power, Fin = 1900 MHz

LOGOUT Voltage & Error

vs. Input Power, Fin = 900 MHz

Unless otherwise noted: Vcc1, Vcc2, Vcc3 = +5V, TA = +25C

HMC602LP4 / 602LP4E

v01.0407 70 dB, LOGARITHMIC

DETECTOR / CONTROLLER, 1 - 8000 MHz

LOGOUT Voltage & Error

vs. Input Power, Fin = 3600 MHz

0.2

0.6

1.4

1.8

2.2

2.6

-3

-2

-1

-70 -60 -50 -40 -30 -20 -10 0

LOGOUT +25C

LOGOUT +85C

LOGOUT -40C

ERR +25C

ERR +85C

ERR -40C

LOGOUT (V)

ERROR (dB)

INPUT POWER (dBm)

IDEAL

0.2

0.6

1.4

1.8

2.2

2.6

-3

-2

-1

-70 -60 -50 -40 -30 -20 -10 0

IDEAL

LOGOUT +25C

LOGOUT +85C

LOGOUT -40C

ERR +25C

ERR +85C

ERR -40C

LOGOUT (V)

ERROR (dB)

INPUT POWER (dBm)

0.2

0.6

1.4

1.8

2.2

2.6

-3

-2

-1

-70 -60 -50 -40 -30 -20 -10 0

LOGOUT +25C

LOGOUT +85C

LOGOUT -40C

ERR +25C

ERR +85C

ERR -40C

LOGOUT (V)

ERROR (dB)

INPUT POWER (dBm)

IDEAL

0.2

0.6

1.4

1.8

2.2

2.6

-3

-2

-1

-70 -60 -50 -40 -30 -20 -10 0

LOGOUT +25C

LOGOUT +85C

LOGOUT -40C

ERR +25C

ERR +85C

ERR -40C

LOGOUT (V)

ERROR (dB)

INPUT POWER (dBm)

IDEAL

0.2

0.7

1.2

1.7

2.2

-5

-70 -60 -50 -40 -30 -20 -10 0 10

LOGOUT +25C

LOGOUT +85C

LOGOUT -40C

ERR +25C

ERR +85C

ERR -40C

LOGOUT (V)

ERROR (dB)

INPUT POWER (dBm)

IDEAL

LOGOUT Voltage & Error

vs. Input Power, Fin = 50 MHz

0.2

0.6

1.4

1.8

2.2

2.6

-3

-2

-1

-70 -60 -50 -40 -30 -20 -10 0

LOGOUT +25C

LOGOUT +85C

LOGOUT -40C

ERR +25C

ERR +85C

ERR -40C

LOGOUT (V)

ERROR (dB)

INPUT POWER (dBm)

IDEAL

POWER DETECTORS - SMT

8 - 25

For price, delivery, and to place orders, please contact Hittite Microwave Corporation:

20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373

Order On-line at www.hittite.com

LOGOUT Voltage & Error

vs. Input Power, Fin = 5800 MHz

Unless otherwise noted: Vcc1, Vcc2, Vcc3 = +5V, TA = +25C

HMC602LP4 / 602LP4E

v01.0407 70 dB, LOGARITHMIC

DETECTOR / CONTROLLER, 1 - 8000 MHz

LOGOUT Voltage & Error

vs. Input Power, Fin = 7500 MHz

LOGOUT Voltage & Error

vs. Input Power, Fin = 8000 MHz

0.2

0.7

1.2

1.7

2.2

-5

-70 -60 -50 -40 -30 -20 -10 0 10

IDEAL

LOGOUT +25C

LOGOUT +85C

LOGOUT -40C

ERR +25C

ERR +85C

ERR -40C

LOGOUT (V)

ERROR (dB)

INPUT POWER (dBm)

0.2

0.7

1.2

1.7

2.2

-5

-70 -60 -50 -40 -30 -20 -10 0 10

LOGOUT +25C

LOGOUT +85C

LOGOUT -40C

ERR +25C

ERR +85C

ERR -40C

LOGOUT (V)

ERROR (dB)

INPUT POWER (dBm)

IDEAL

0.2

0.6

1.4

1.8

2.2

-5

-70 -60 -50 -40 -30 -20 -10 0 10

LOGOUT +25C

LOGOUT +85C

LOGOUT -40C

ERR +25C

ERR +85C

ERR -40C

LOGOUT (V)

ERROR (dB)

INPUT POWER

(

dBm

)

IDEAL

LOGOUT Voltage & Error

vs. Input Power, Fin = 7000 MHz

0.2

0.7

1.2

1.7

2.2

-5

-70 -60 -50 -40 -30 -20 -10 0 10

LOGOUT +25C

LOGOUT +85C

LOGOUT -40C

ERR +25C

ERR +85C

ERR -40C

LOGOUT (V)

ERROR (dB)

INPUT POWER (dBm)

IDEAL

LOGOUT Slope vs. Frequency LOGOUT Slope vs. Supply Voltage

-32

-30

-28

-26

-24

-22

-20

1000 2000 3000 4000 5000 6000 7000 8000

+25 C

+85 C

-40 C

SLOPE (mV/dB)

FREQUENCY (MHz)

-30

-28

-26

-24

-22

-20

4.5 5 5.5

100 MHz

1900 MHz

3600 MHz

5800 MHz

8000 MHz

SLOPE (mV/dB)

Vcc1, Vcc2, Vcc3 (Volts)

POWER DETECTORS - SMT

8 - 26

For price, delivery, and to place orders, please contact Hittite Microwave Corporation:

20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373

Order On-line at www.hittite.com

HMC602LP4 / 602LP4E

v01.0407 70 dB, LOGARITHMIC

DETECTOR / CONTROLLER, 1 - 8000 MHz

LOGOUT Error vs. Input Power,

Normalized [2], Fin= 1900 MHz

-2

-1.5

-1

-0.5

0.5

1.5

-70 -60 -50 -40 -30 -20 -10 0

+85 C

-40 C

ERROR (dB)

INPUT POWER (dBm)

LOGOUT Voltage

vs. Input Power & Frequency

0.2

0.4

0.6

0.8

1.2

1.4

1.6

1.8

2.2

2.4

-70 -60 -50 -40 -30 -20 -10 0 10

50 MHz

100 MHz

900 MHz

1900 MHz

2200 MHz

3600 MHz

5800 MHz

6500 MHz

7000 MHz

7500 MHz

8000 MHz

LOGOUT (V)

INPUT POWER

(

dBm

)

LOGOUT Intercept vs. Supply VoltageLOGOUT Intercept vs. Frequency

0 1000 2000 3000 4000 5000 6000 7000 8000

+25 C

+85 C

-40 C

INTERCEPT (dBm)

FREQUENCY (MHz)

Input Impedance vs Frequency [3]

1.0

0.9

0.8

0.7

1.2

1.4

1.6

1.8

2.0

0.6

0.5

0.4

0.3

0.2

0.1

3.0

6.0

8.0

5.0

4.0

RF Café

2002

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

2.0

3.0

4.0

5.0

1.0

0.9

0.8

0.7

1.2

1.4

1.6

1.8

2.0

3.0

6.0

8.0

5.0

4.0

0.6

0.5

0.4

0.3

0.2

0.1

S11

5.8 GHz

4.7 GHz

2.2 GHz

1.9 GHz

0.9 GHz

0.1 GHz

8.0 GHz

3.6 GHz

6.8 GHz

[1] Unless otherwise noted: Vcc1, Vcc2, Vcc3 = +5V, TA = +25C

[2] This data is relative to the room temperature performance of

the HMC602LP4(E)

[3] Reference plane at J1 connector on eval board

4.5 5 5.5

100MHz

1900 MHz

3600 MHz

5800 MHz

8000 MHz

INTERCEPT (dBm)

Vcc1, Vcc2, Vcc3 (Volts)

POWER DETECTORS - SMT

8 - 27

For price, delivery, and to place orders, please contact Hittite Microwave Corporation:

20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373

Order On-line at www.hittite.com

Absolute Maximum Ratings

Vcc1, Vcc2, Vcc3 +5.5V

EN +5.5V

VSET Input Voltage +5.5V

LOGOUT Output Current 3 mA

RF Input Power +15 dBm

Junction Temperature 125 °C

Continuous Pdiss (T = 85°C)

(Derate 7.95 mW/°C above 85°C) 1.55 Watts

Thermal Resistance (Rth)

(junction to lead) 42 °C/W

Storage Temperature -65 to +150 °C

Operating Temperature -40 to +85 °C

ELECTROSTATIC SENSITIVE DEVICE

OBSERVE HANDLING PRECAUTIONS

Outline Drawing

Part Number Package Body Material Lead Finish MSL Rating Package Marking [3]

HMC602LP4 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 [1] H602

XXXX

HMC602LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 [2] H602

XXXX

[1] Max peak re ow temperature of 235 °C

[2] Max peak re ow temperature of 260 °C

[3] 4-Digit lot number XXXX

Package Information

NOTES:

1. LEADFRAME MATERIAL: COPPER ALLOY

2. DIMENSIONS ARE IN INCHES [MILLIMETERS].

3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE

4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.

PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.

5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.

6. ALL GROUND LEADS AND GROUND PADDLE MUST

BE SOLDERED TO PCB RF GROUND.

7. REFER TO HMC APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN.

HMC602LP4 / 602LP4E

v01.0407 70 dB, LOGARITHMIC

DETECTOR / CONTROLLER, 1 - 8000 MHz

POWER DETECTORS - SMT

8 - 28

For price, delivery, and to place orders, please contact Hittite Microwave Corporation:

20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373

Order On-line at www.hittite.com

Pin Number Function Description Interface Schematic

1, 6, 7, 13,

17, 18 N/C

These pins are not connected internally; however,

this product is speci ed with these pins connected

to RF/DC ground.

2 TEMP Temperature sensor output pin.

3, 4 INP, INN RF Input pins. Connect RF to INP, and AC couple

INN to ground for single-ended operation.

5EN

Enable pin, connect to Vcc1, Vcc2, Vcc3 for normal

operation. Applying voltage <0.2 x (Vcc1, Vcc2, Vcc3) will

initiate power saving mode.

8 - 12, 19, 20,

23, 24

Vcc1, Vcc2,

Vcc3

Bias supply. Connect supply voltage to

these pins with appropriate  ltering.

14 CLPF Loop  lter capacitor for output ripple  ltering.

Pin Descriptions

HMC602LP4 / 602LP4E

v01.0407 70 dB, LOGARITHMIC

DETECTOR / CONTROLLER, 1 - 8000 MHz

POWER DETECTORS - SMT

8 - 29

For price, delivery, and to place orders, please contact Hittite Microwave Corporation:

20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373

Order On-line at www.hittite.com

HMC602LP4 / 602LP4E

v01.0407 70 dB, LOGARITHMIC

DETECTOR / CONTROLLER, 1 - 8000 MHz

Pin Number Function Description Interface Schematic

15 LOGOUT

Logarithmic output that converts the input power

to a DC level in detector mode. Short this pin to

VSET for detector mode.

16 VSET VSET input in controller mode. Short this

pin to LOGOUT for detector mode.

21, 22 CPB, CPA Temperature compensation pins. Connect CPB directly

to ground and leave CPA  oating for all frequencies

Package Base GND Exposed paddle must be connected to RF and DC ground.

Pin Descriptions (Continued)

POWER DETECTORS - SMT

8 - 30

For price, delivery, and to place orders, please contact Hittite Microwave Corporation:

20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373

Order On-line at www.hittite.com

Application & Evaluation PCB Schematic

Notes

Note 1: The HMC602LP4 & HMC602LP4E evaluation boards are pre-assembled for single-ended input, and detector/RSSI mode.

Note 2: For detector mode, connect high impedance volt meter to the LOGOUT port, and make no connection to VSET. LOGOUT

is shorted to VSET by R9, as required for detector mode.

Note 3: For controller mode, remove R9 and install 0 ohm resistor (R11), then make appropriate connection to LOGOUT and VSET.

In controller mode, the LOGOUT output can be used to drive a variable gain ampli er, or a variable attenuator, either

directly or through a buffer or microcontroller. VSET should be connected to an external supply, typically between +0.6

and +1.9V.

Note 4: Terminal CPB must be connected to ground for proper operation.

HMC602LP4 / 602LP4E

v01.0407 70 dB, LOGARITHMIC

DETECTOR / CONTROLLER, 1 - 8000 MHz

POWER DETECTORS - SMT

8 - 31

For price, delivery, and to place orders, please contact Hittite Microwave Corporation:

20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373

Order On-line at www.hittite.com

HMC602LP4 / 602LP4E

v01.0407 70 dB, LOGARITHMIC

DETECTOR / CONTROLLER, 1 - 8000 MHz

Item Description

J1 - J3 PC Mount SMA Connector

J4 Molex Connector Header

J5 - J11 DC Pin

C1, C2 1000 pF Capacitor, 0402 Pkg.

C3, C5, C7 100 pF Capacitor, 0402 Pkg.

C4, C6, C8 0.1μF Capacitor, 0603 Pkg.

C9 220 pF Capacitor, 0603 Pkg.

R1 68Ω Resistor, 0603 Pkg.

R2 1k Ω Resistor, 0603 Pkg.

R3 10k Ω Resistor, 0603 Pkg.

R4 - R6, R9 0Ω Resistor, 0603 Pkg.

R8, R12 0Ω Resistor, 0402 Pkg.

U1 HMC602LP4 / HMC602LP4E

Logarithmic Detector / Controller

PCB [2] 11540 0 Eval B oard

[1] Reference this number when ordering complete evaluation PCB

[2] Circuit Board Material: Rogers 4350

Evaluation PCB

The circuit board used in the  nal application should

use RF circuit design techniques. Signal lines

should have 50 ohm impedance while the package

ground leads and exposed paddle should be con-

nected directly to the ground plane similar to that

shown. A suf cient number of via holes should be

used to connect the top and bottom ground planes.

The evaluation circuit board shown is available from

Hittite upon request.

List of Materials for Evaluation PCB 115402 [1]