1-157
T-13/4, 2 mm X 5 mm Rectangular
Bicolor LED Lamps
High Efficiency Red/
High Performance Green
Technical Data
H
Features:
• Two Color (Red, Green)
Operation
• (Other Two LED Color
Combinations Available)
• Three Leads with One
Common Cathode
• Option of Straight or Spread
Lead Configurations
• Diffused, Wide Visibility
Lens
Description
The T-1 3/4 HLMP-4000 and
2 mm by 5 mm rectangular
HLMP-0800 are three leaded
bicolor light sources designed for
a variety of applications where
dual state illumination is required
in the same package. There are
two LED chips, high efficiency
red (HER), and high performance
green (Green), mounted on a
central common cathode lead for
maximum on-axis viewability.
Colors between HER and Green
can be generated by
independently pulse width
modulating the LED chips.
Other Bicolor
Combinations
Other bicolor combinations are
available:
• HER/yellow
• HER/green
• DH AlGaAs red/green.
Contact your local Hewlett-
Packard Components Field Sales
representative for details.
Package Dimensions
HLMP-4000 HLMP-0800
HLMP-4000
HLMP-0800
5964-9363E
1-158
Notes:
1. See Figure 5 to establish pulsed operating conditions.
2. The combined simultaneous current must not exceed the maximum.
3. The combined simultaneous power must not exceed the maximum.
4. For HER and Green derate linearly from 50°C at 0.5 mA/°C.
5. For HER and Green derate linearly from 25°C at 1.8 mW/°C.
6. The transient peak current is the maximum non-recurring current that can be applied
to the device without damaging the LED die and wirebond. It is not recommended that
the device be operated at peak currents beyond the peak forward current listed in the
Absolute Maximum Ratings.
High Efficiency
Parameter Red/Green Units
Peak Forward Current 90 mA
Average Forward Current[1,2] (Total) 25 mA
DC Current[2,4] (Total) 30 mA
Power Dissipation[3,5] (Total) 135 mW
Operating Temperature Range -20 to +85 °C
Storage Temperature Range -55 to +100
Reverse Voltage (IR = 100 µA) 5 V
Transient Forward Current[6] 500 mA
(10 µsec Pulse)
Lead Soldering Temperature
[1.6 mm (0.063 in.) below 260°C for 5 seconds
seating plane]
Absolute Maximum Ratings at T
A = 25°C
Package Dimensions, continued
0.89 (0.035)
0.64 (0.025)
6.10 (0.240)
5.59 (0.220)
5.08 (0.200)
4.57 (0.180)
20.32
(0.800) MIN.
0.508
(0.020)
9.19 (0.362)
8.43 (0.332)
2.54 ± 0.25
(0.100 ± 0.010)
SQUARE
NOMINAL
GREEN
ANODE
2.54 ± 0.25
(0.100 ± 0.010)
COMMON
CATHODE
FLAT INDICATES
RED ANODE
RED ANODE
(SHORT LEAD)
COMMON CATHODE
5.46 (0.215)
4.98 (0.196)
5.18 (0.204)
4.93 (0.194)
20.32
(0.800)
MIN. 0.508
(0.020)
8.00 (0.315)
7.37 (0.290)
2.54 ± 0.25
(0.100 ± 0.010)
SQUARE
NOMINAL
GREEN
ANODE
2.54 ± 0.25
(0.100 ± 0.010)
COMMON
CATHODE
RED ANODE
(SHORT LEAD)
COMMON CATHODE
2.54 ± 0.25
(0.100 ± 0.010)
2.41 (0.095)
2.03 (0.085)
2.23 (0.088)
1.98 (0.078)
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES).
2. AN EPOXY MENISCUS MAY EXTEND ABOUT
1 MM (0.040") DOWN THE LEADS.
SIDE VIEW
2.54 ± 0.25
(0.100 ± 0.010)
1-159
Notes:
1. The dominant wavelength, λd, is derived from the CIE chromaticity diagram and represents the single wavelength which defines the
color of the device.
2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity.
3. Radiant intensity, Ie, in watts steradian, may be found from the equation Ie = Iv/ηv where Iv is the luminous intensity in candelas and
ηv is the luminous efficacy in lumens/watt.
Red Green Test
Sym. Parameter Min. Typ. Max. Min. Typ. Max. Units Conditions
IVLuminous Intensity
HLMP-4000 2.1 5 4.2 8 IF = 10 mA
mcd
HLMP-0800 2.1 3.5 2.6 4.0 IF = 20 mA
λPEAK Peak Wavelength 635 565 nm
λdDominant 626 569
Wavelength[1]
τsSpeed of Response 90 500 ns
C Capacitance 11 18 pF VF = 0, f = 1 MHz
VFForward Voltage 1.9 2.4 2.1 2.7 V IF = 10 mA
VRReverse Breakdown 5 5 V IR = 100 µA
Voltage
RθJ-PIN Thermal Resistance 260 260 °C/W Junction to
Cathode Lead
Included Angle
Between Half
Luminous
Intensity Points[2]
2θ 1/2HLMP-4000 65 65 IF = 10 mA
Deg.
HLMP-0800 100 100 IF = 20 mA
ηVLuminous Efficacy[3] 145 595 Lumen/
Watt
Figure 1. Relative Intensity vs. Wavelength.
Electrical/Optical Characteristics at TA = 25°C
1-160
Figure 2. Forward Current vs.
Forward Voltage Characteristics.
Figure 5. Maximum Tolerable Peak Current vs.
Pulse Duration. (IDC MAX as per MAX
Ratings).
Figure 7. Relative Luminous Intensity vs. Angular
Displacement for the HLMP-0800.
Figure 6. Relative Luminous Intensity vs. Angular
Displacement for the HLMP-4000.
Figure 3. Relative Luminous Intensity
vs. DC Forward Current. Figure 4. Relative Efficiency
(Luminous Intensity per Unit
Current) vs. Peak LED Current.