LM4922 LM4922 Ground-Referenced, Ultra Low Noise, Fixed Gain, 80mW Stereo Headphone Amplifier Literature Number: SNAS327D OBSOLETE October 3, 2011 Ground-Referenced, Ultra Low Noise, Fixed Gain, 80mW Stereo Headphone Amplifier General Description Key Specifications The LM4922 is a ground referenced, fixed-gain audio power amplifier capable of delivering 80mW of continuous average power into a 16 single-ended load with less than 1% THD +N from a 3V power supply. The LM4922 features a new circuit technology that utilizes a charge pump to generate a negative reference voltage. This allows the outputs to be biased about ground, thereby eliminating output-coupling capacitors typically used with normal single-ended loads. The LM4922 features an Automatic Standby Mode circuitry (patent pending). In the absence of an input signal, after approximately 12 seconds, the LM4922 goes into low current standby mode. The LM4922 recovers into full power operating mode immediately after a signal is applied to either the left or right input pins. This feature saves power supply current in battery operated applications. Boomer audio power amplifiers were designed specifically to provide high quality output power with a minimal amount of external components. The LM4922 does not require output coupling capacitors or bootstrap capacitors, and therefore is ideally suited for mobile phone and other low voltage applications where minimal power consumption is a primary requirement. The LM4922 features a low-power consumption shutdown mode selectable for either channel separately. This is accomplished by driving either the SD_RC (Shutdown Right Channel) or SD_LC (Shutdown Left Channel) (or both) pins with logic low, depending on which channel is desired shutdown. Additionally, the LM4922 features an internal thermal shutdown protection mechanism. The LM4922 contains advanced pop & click circuitry that eliminates noises which would otherwise occur during turn-on and turn-off transitions. The LM4922 has an internal fixed gain of 1.5V/V. Improved PSRR at 217Hz 70dB (typ) Power Output at VDD = 3V, RL = 16, THD 1% 80mW (typ) Shutdown Current 0.01A (typ) Internal Fixed Gain 1.5V/V (typ) Operating Voltage 1.6V to 4.2V Features Fixed Logic Levels Ground referenced outputs High PSRR Available in space-saving micro SMD package Ultra low current shutdown mode Improved pop & click circuitry eliminates noises during turn-on and turn-off transitions No output coupling capacitors, snubber networks, bootstrap capacitors, or gain-setting resistors required Shutdown either channel independently Applications Notebook PCs Mobile Phone PDAs Portable electronic devices MP3 Players Boomer(R) is a registered trademark of National Semiconductor Corporation. (c) 2011 National Semiconductor Corporation 201582 201582 Version 5 Revision 2 www.national.com Print Date/Time: 2011/10/03 14:26:28 LM4922 Ground-Referenced, Ultra Low Noise, Fixed Gain, 80mW Stereo Headphone Amplifier LM4922 LM4922 Typical Application 201582b8 FIGURE 1. Typical Audio Amplifier Application Circuit www.national.com 2 201582 Version 5 Revision 2 Print Date/Time: 2011/10/03 14:26:28 LM4922 Connection Diagrams microSMD Package 16 - Bump TL Marking 20158278 Top View XY - Date Code TT - Lot Traceability G - Boomer Family G1 - LM4922TL 20158209 Top View Order Number LM4922TL See NS Package Number TLE1411A Pin Descriptions Pin Name Function A1 R_IN Right Channel Input A2 SGND Signal Ground A3 CPVDD Charge Pump Power Supply A4 CCP+ Positive Terminal - Charge Pump Flying Capacitor B1 SD_RC Active-Low Shutdown, Right Channel B2 SD_LC Active-Low Shutdown, Left Channel B4 PGND Power Ground C1 L_IN Left Channel Input C2 R_OUT Right Channel Input C4 CCP- Negative Terminal - Charge Pump Flying Capacitor D1 +AVDD Positive Power Supply - Amplifier D2 L_OUT Left Channel Output D3 -AVDD Negative Power Supply - Amplifier D4 VCP_OUT Charge Pump Power Output 3 201582 Version 5 Revision 2 Print Date/Time: 2011/10/03 14:26:28 www.national.com LM4922 Junction Temperature Thermal Resistance Absolute Maximum Ratings (Note 2) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage Storage Temperature Input Voltage Power Dissipation (Note 3) ESD Susceptibility (Note 4) ESD Susceptibility (Note 5) JA (typ) TLE1411A (Note 11) 86C/W Operating Ratings 4.5V -65C to +150C -0.3V to VDD + 0.3V Internally Limited 2000V 200V Electrical Characteristics VDD = 3V 150C Temperature Range TMIN TA TMAX -40C TA 85C 1.6V VDD 4.2V Supply Voltage (VDD) (Note 1) The following specifications apply for VDD = 3V and 16 load unless otherwise specified. Limits apply to TA = 25C. LM4922 Symbol Parameter Conditions Quiescent Power Supply Current VIN = 0V, inputs terminated Auto Standby Mode both channels enabled IDD VIN = 0V, inputs terminated Quiescent Power Supply Current both channels enabled Full Power Mode VIN = 0V, inputs terminated one channel enabled Typ (Note 6) Limit (Note 7) (Note 8) 2.3 7 Units (Limits) mA 10 5 mA (max) mA ISD Shutdown Current VSD_LC = VSD_RC = GND 0.1 1.8 A (max) VOS Output Offset Voltage RL = 32, VIN = 0V 0.7 5 mV (max) AV Voltage Gain -1.5 V/V AV Gain Match 1 % RIN Input Resistance 20 PO THD+N Output Power Total Harmonic Distortion + Noise 15 25 k (min) k (max) THD+N = 1% (max); f = 1kHz, RL = 16, one channel 80 mW THD+N = 1% (max); f = 1kHz, RL = 32, one channel 65 mW THD+N = 1% (max); f = 1kHz, RL = 16, (two channels in phase) 43 38 mW (min) THD+N = 1% (max); f = 1kHz, RL = 32, (two channels in phase) 50 45 mW (min) PO = 60mW, f = 1kHz, RL = 16 single channel 0.04 PO = 50mW, f = 1kHz, RL = 32 single channel 0.03 % VRIPPLE = 200mVp-p, Input Referred PSRR Power Supply Rejection Ratio Full Power Mode f = 217Hz 70 f = 1kHz 65 f = 20kHz 50 SNR Signal-to-Noise Ratio RL = 32, POUT = 20mW, (A-weighted) f = 1kHz, BW = 20Hz to 22kHz VIH Shutdown Input Voltage High VDD = 1.8V to 4.2V VIL Shutdown Input Voltage Low VDD = 1.8V to 4.2V TWU Wake Up Time From AutoStandby www.national.com 100 5 4 201582 Version 5 Revision 2 dB Print Date/Time: 2011/10/03 14:26:28 dB 1.2 V (min) 0.45 V (max) s Symbol Parameter Conditions Typ (Note 6) XTALK Crosstalk RL = 16, PO = 1.6mW, f = 1kHz 60 ZOUT Output Impedance VSD-LC = VSD-RC = GND Input Terminated Input not terminated 50 Limit (Note 7) (Note 8) Units (Limits) dB 30 k 2 k (min) VSD-LC = VSD-RC = GND -500mV VOUT +500mV (Note 12) ZOUT Output Impedance IL Input Leakage 0.1 nA VIN THRESH Input Voltage Threshold 2.8 mVp 8 Note 1: All voltages are measured with respect to the GND pin unless otherwise specified. Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions that guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given; however, the typical value is a good indication of device performance. Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA, and the ambient temperature, TA. The maximum allowable power dissipation is PDMAX = (TJMAX - TA) / JA or the number given in Absolute Maximum Ratings, whichever is lower. For the LM4922, see power derating currents for more information. Note 4: Human body model, 100pF discharged through a 1.5k resistor. Note 5: Machine Model, 220pF - 240pF discharged through all pins. Note 6: Typicals are measured at 25C and represent the parametric norm. Note 7: Limits are guaranteed to National's AOQL (Average Outgoing Quality Level). Note 8: Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis. Note 9: If the product is in shutdown mode and VDD exceeds 4.2V (to a max of 4.5V VDD), then most of the excess current will flow through the ESD protection circuits. If the source impedance limits the current to a max of 10mA, then the part will be protected. If the part is enabled when VDD is above 4.5V, circuit performance will be curtailed or the part may be permanently damaged. Note 10: Human body model, 100pF discharged through a 1.5k resistor. Note 11: JA value is measured with the device mounted on a PCB with a 3" x 1.5", 1oz copper heatsink. Note 12: VOUT refers to signal applied to the LM4922 outputs. External Components Description (Figure 1) Components 1. Functional Description Ci Input coupling capacitor which blocks the DC voltage at the amplifier's input terminals. Also creates a high-pass 2. C1 Flying capacitor. Low ESR ceramic capacitor (100m) 3. C2 Output capacitor. Low ESR ceramic capacitor (100m) 4. C3 Tantalum capacitor. Supply bypass capacitor which provides power supply filtering. Refer to the Power Supply Bypassing section for information concerning proper placement and selection of the supply bypass capacitor. 5. C4 Ceramic capacitor. Supply bypass capacitor which provides power supply filtering. Refer to the Power Supply Bypassing section for information concerning proper placement and selection of the supply bypass capacitor. filter with Ri at fC = 1/(2RiCi). Refer to the section Proper Selection of External Components, for an explanation of how to determine the value of Ci. 5 201582 Version 5 Revision 2 Print Date/Time: 2011/10/03 14:26:28 www.national.com LM4922 LM4922 LM4922 Typical Performance Characteristics THD+N vs Frequency VDD = 1.6V, RL = 16, PO = 1mW THD+N vs Frequency VDD = 1.6V, RL = 32, PO = 1mW 20158228 20158229 THD+N vs Frequency VDD = 1.8V, RL = 16, PO = 5mW THD+N vs Frequency VDD = 1.8V, RL = 32, PO = 5mW 20158230 www.national.com 20158231 6 201582 Version 5 Revision 2 Print Date/Time: 2011/10/03 14:26:28 LM4922 THD+N vs Frequency VDD = 3V, RL = 16, PO = 50mW THD+N vs Frequency VDD = 3V, RL = 32, PO = 50mW 20158232 20158233 THD+N vs Frequency VDD = 3.6V, RL = 16, PO = 100mW THD+N vs Frequency VDD = 3.6V, RL = 32, PO = 100mW 20158234 20158235 7 201582 Version 5 Revision 2 Print Date/Time: 2011/10/03 14:26:28 www.national.com LM4922 THD+N vs Frequency VDD = 4.2V, RL = 16, PO = 150mW THD+N vs Frequency VDD = 4.2V, RL = 32, PO = 150mW 20158236 20158237 THD+N vs Output Power VDD = 1.6V, RL = 16, f = 1kH One channel enabled THD+N vs Output Power VDD = 1.6V, RL = 32, f = 1kHz One channel enabled 20158249 20158247 www.national.com 8 201582 Version 5 Revision 2 Print Date/Time: 2011/10/03 14:26:28 LM4922 THD+N vs Output Power VDD = 1.6V, RL = 16, f = 1kHz Two channels in phase THD+N vs Output Power VDD = 1.6V, RL = 32, f = 1kHz Two channels in phase 20158253 20158251 THD+N vs Output Power VDD = 1.8V, RL = 16, f = 1kHz One channel enabled THD+N vs Output Power VDD = 1.8V, RL = 32, f = 1kHz One channel enabled 20158259 20158261 9 201582 Version 5 Revision 2 Print Date/Time: 2011/10/03 14:26:28 www.national.com LM4922 THD+N vs Output Power VDD = 1.8V, RL = 16, f = 1kHz Two channels in phase THD+N vs Output Power VDD = 1.8V, RL = 32, f = 1kHz Two channels in phase 20158263 20158265 THD+N vs Output Power VDD = 3.0V, RL = 16, f = 1kHz One channel enabled THD+N vs Output Power VDD = 3.0V, RL = 32, f = 1kHz One channel enabled 201582e1 201582g2 www.national.com 10 201582 Version 5 Revision 2 Print Date/Time: 2011/10/03 14:26:28 LM4922 THD+N vs Output Power VDD = 3.0V, RL = 16, f = 1kHz Two channels in phase THD+N vs Output Power VDD = 3.0V, RL = 32, f = 1kHz Two channels in phase 201582e5 201582g4 THD+N vs Output Power VDD = 3.6V, RL = 16, f = 1kHz One channel enabled THD+N vs Output Power VDD = 3.6V, RL = 32, f = 1kHz One channel enabled 201582f1 201582f3 11 201582 Version 5 Revision 2 Print Date/Time: 2011/10/03 14:26:28 www.national.com LM4922 THD+N vs Output Power VDD = 3.6V, RL = 16, f = 1kHz Two channels in phase THD+N vs Output Power VDD = 3.6V, RL = 32, f = 1kHz two channels in phase 201582f5 201582f7 THD+N vs Output Power VDD = 4.2V, RL = 16, f = 1kHz One channel enabled THD+N vs Output Power VDD = 4.2V, RL = 32, f = 1kHz One channel enabled 20158273 www.national.com 20158280 12 201582 Version 5 Revision 2 Print Date/Time: 2011/10/03 14:26:28 LM4922 THD+N vs Output Power VDD = 4.2V, RL = 16, f = 1kHz Two channels in phase THD+N vs Output Power VDD = 4.2V, RL = 32, f = 1kHz Two channels in phase 20158282 20158284 PSRR vs Frequency VDD = 1.6V, RL = 16 PSRR vs Frequency VDD = 1.6V, RL = 32 20158240 20158241 13 201582 Version 5 Revision 2 Print Date/Time: 2011/10/03 14:26:28 www.national.com LM4922 PSRR vs Frequency VDD = 3V, RL = 16 PSRR vs Frequency VDD = 3V, RL = 32 20158243 20158242 PSRR vs Frequency VDD = 4.2V, RL = 16 PSRR vs Frequency VDD = 4.2V, RL = 32 20158244 www.national.com 20158245 14 201582 Version 5 Revision 2 Print Date/Time: 2011/10/03 14:26:28 LM4922 Output Power vs Supply Voltage RL = 16, one channel Output Power vs Supply Voltage RL = 32, one channel 20158239 20158238 Output Power vs Supply Voltage RL = 16, 2 channels in phase Output Power vs Supply Voltage RL = 32, 2 channels in phase 201582g8 201582g9 15 201582 Version 5 Revision 2 Print Date/Time: 2011/10/03 14:26:28 www.national.com LM4922 Supply Current vs Supply Voltage RL = 16 Representation of Automatic Standby Mode Behavior VDD = 3V 20158219 20158289 www.national.com 16 201582 Version 5 Revision 2 Print Date/Time: 2011/10/03 14:26:28 SUPPLY VOLTAGE SEQUENCING It is a good general practice to first apply the supply voltage to a CMOS device before any other signal or supply on other pins. This is also true for the LM4922 audio amplifier which is a CMOS device. Before applying any signal to the inputs or shutdown pins of the LM4922, it is important to apply a supply voltage to the VDD pins. After the device has been powered, signals may be applied to the shutdown pins (see MICRO POWER SHUTDOWN) and input pins. Since the LM4922 has two operational amplifiers in one package, the maximum internal power dissipation point is twice that of the number which results from Equation 1. Even with large internal power dissipation, the LM4922 does not require heat sinking over a large range of ambient temperatures. From Equation 1, assuming a 3V power supply and a 16 load, the maximum power dissipation point is 28mW per amplifier. Thus the maximum package dissipation point is 56mW. The maximum power dissipation point obtained must not be greater than the power dissipation that results from Equation 2: ELIMINATING THE OUTPUT COUPLING CAPACITOR The LM4922 features a low noise inverting charge pump that generates an internal negative supply voltage. This allows the outputs of the LM4922 to be biased about GND instead of a nominal DC voltage, like traditional headphone amplifiers. Because there is no DC component, the large DC blocking capacitors (typically 220F) are not necessary. The coupling capacitors are replaced by two, small ceramic charge pump capacitors, saving board space and cost. Eliminating the output coupling capacitors also improves low frequency response. In traditional headphone amplifiers, the headphone impedance and the output capacitor form a high pass filter that not only blocks the DC component of the output, but also attenuates low frequencies, impacting the bass response. Because the LM4922 does not require the output coupling capacitors, the low frequency response of the device is not degraded by external components. In addition to eliminating the output coupling capacitors, the ground referenced output nearly doubles the available dynamic range of the LM4922 when compared to a traditional headphone amplifier operating from the same supply voltage. PDMAX = (TJMAX - TA) / (JA) (2) For the micro SMD package, JA = 105C/W. TJMAX = 150C for the LM4922. Depending on the ambient temperature, TA, of the system surroundings, Equation 2 can be used to find the maximum internal power dissipation supported by the IC packaging. If the result of Equation 1 is greater than that of Equation 2, then either the supply voltage must be decreased, the load impedance increased or TA reduced. For the typical application of a 3V power supply, with a 16 load, the maximum ambient temperature possible without violating the maximum junction temperature is approximately 144C provided that device operation is around the maximum power dissipation point. Power dissipation is a function of output power and thus, if typical operation is not around the maximum power dissipation point, the ambient temperature may be increased accordingly. POWER SUPPLY BYPASSING As with any power amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection. Applications that employ a 3V power supply typically use a 4.7F capacitor in parallel with a 0.1F ceramic filter capacitor to stabilize the power supply's output, reduce noise on the supply line, and improve the supply's transient response. Keep the length of leads and traces that connect capacitors between the LM4922's power supply pin and ground as short as possible. OUTPUT TRANSIENT ('CLICK AND POPS') ELIMINATED The LM4922 contains advanced circuitry that virtually eliminates output transients ('clicks and pops'). This circuitry prevents all traces of transients when the supply voltage is first applied or when the part resumes operation after coming out of shutdown mode. AMPLIFIER CONFIGURATION EXPLANATION As shown in Figure 2, the LM4922 has two internal operational amplifiers. The two amplifiers have internally configured gain, the closed loop gain is set by selecting the ratio of Rf to Ri. Consequently, the gain for each channel of the IC is AUTOMATIC STANDBY MODE The LM4922 features Automatic Standby Mode circuitry (patent pending). In the absence of an input signal, after approximately 12 seconds, the LM4922 goes into low current standby mode. The LM4922 recovers into full power operating mode immediately after a signal, which is greater than the input threshold voltage, is applied to either the left or right input pins. The input threshold voltage is not a static value, as the supply voltage increases, the input threshold voltage decreases. This feature reduces power supply current consumption in battery operated applications. Please see also the graph entitled Representation of Automatic Standby Mode Behavior in the Typical Performance Characteristics section. To ensure correct operation of Automatic Standby Mode, proper layout techniques should be implemented. Separating PGND and SGND can help reduce noise entering the LM4922 in noisy environments. Auto Standby mode works best when output impedance of the audio source driving LM4922 is equal or less than 50 Ohms. While Automatic Standby Mode reduces power consumption very effectively during silent pe- AV = -(Rf / Ri) = 1.5 V/V where RF = 30k and Ri = 20k. Since this is an output ground-referenced amplifier, by driving the headphone through ROUT (Pin C2) and LOUT (Pin D2), the LM4922 does not require output coupling capacitors. The typical single-ended amplifier configuration requires large, expensive output capacitors. POWER DISSIPATION Power dissipation is a major concern when using any power amplifier and must be thoroughly understood to ensure a successful design. Equation 1 states the maximum power dissipation point for a single-ended amplifier operating at a given supply voltage and driving a specified output load. 17 201582 Version 5 Revision 2 (1) Print Date/Time: 2011/10/03 14:26:28 www.national.com LM4922 PDMAX = (VDD) 2 / (22RL) Application Information LM4922 riods, maximum power saving is achieved by putting the device into shutdown when it is not in use. charge pump output resistance. Beyond 3.3uF, the switch-on resistance dominates the output impedance for capacitor values above 2.2uF. The output ripple is affected by the value and ESR of the output capacitor (C2). Larger capacitors reduce output ripple on the negative power supply. Lower ESR capacitors minimize the output ripple and reduce the output impedance of the charge pump. The LM4922 charge pump design is optimized for 2.2uF, low ESR, ceramic, flying, and output capacitors. MICRO POWER SHUTDOWN The voltage applied to the SD_LC (shutdown left channel) pin and the SD_RC (shutdown right channel) pin controls the LM4922's shutdown function. When active, the LM4922's micropower shutdown feature turns off the amplifiers' bias circuitry, reducing the supply current. The trigger point is 0.45V for a logic-low level, and 1.2V for logic-high level. The low 0.01A (typ) shutdown current is achieved by applying a voltage that is as near as ground a possible to the SD_LC/ SD_RC pins. A voltage that is higher than ground may increase the shutdown current. There are a few ways to control the micro-power shutdown. These include using a single-pole, single-throw switch, a microprocessor, or a microcontroller. When using a switch, connect an external 100k pull-up resistor between the SD_LC/SD_RC pins and VDD. Connect the switch between the SD_LC/SD_RC pins and ground. Select normal amplifier operation by opening the switch. Closing the switch connects the SD_LC/SD_RC pins to ground, activating micro-power shutdown. The switch and resistor guarantee that the SD_LC/SD_RC pins will not float. This prevents unwanted state changes. In a system with a microprocessor or microcontroller, use a digital output to apply the control voltage to the SD_LC/SD_RC pins. Driving the SD_LC/SD_RC pins with active circuitry eliminates the pull-up resistor. Input Capacitor Value Selection Amplifying the lowest audio frequencies requires high value input coupling capacitors (Ci in Figure 1). A high value capacitor can be expensive and may compromise space efficiency in portable designs. In many cases, however, the speakers used in portable systems, whether internal or external, have little ability to reproduce signals below 150Hz. Applications using speakers with this limited frequency response reap little improvement by using high value input and output capacitors. Besides affecting system cost and size, Ci has an effect on the LM4922's click and pop performance. The magnitude of the pop is directly proportional to the input capacitor's size. Thus, pops can be minimized by selecting an input capacitor value that is no higher than necessary to meet the desired -3dB frequency. As shown in Figure 1, the internal input resistor, Ri and the input capacitor, Ci, produce a -3dB high pass filter cutoff frequency that is found using Equation (3). Conventional headphone amplifiers require output capacitors; Equation (3) can be used, along with the value of RL, to determine towards the value of output capacitor needed to produce a -3dB high pass filter cutoff frequency. SELECTING PROPER EXTERNAL COMPONENTS Optimizing the LM4922's performance requires properly selecting external components. Though the LM4922 operates well when using external components with wide tolerances, best performance is achieved by optimizing component values. Charge Pump Capacitor Selection Use low ESR (equivalent series resistance) (<100m) ceramic capacitors with an X7R dielectric for best performance. Low ESR capacitors keep the charge pump output impedance to a minimum, extending the headroom on the negative supply. Higher ESR capacitors result in reduced output power from the audio amplifiers. Charge pump load regulation and output impedance are affected by the value of the flying capacitor (C1). A larger valued C1 (up to 3.3uF) improves load regulation and minimizes www.national.com fi-3dB = 1 / 2RiCi Also, careful consideration must be taken in selecting a certain type of capacitor to be used in the system. Different types of capacitors (tantalum, electrolytic, ceramic) have unique performance characteristics and may affect overall system performance. (See the section entitled Charge Pump Capacitor Selection.) 18 201582 Version 5 Revision 2 (3) Print Date/Time: 2011/10/03 14:26:28 LM4922 LM4922 micro SMD DEMO BOARD ARTWORK Top Layer Mid Layer 1 20158205 20158206 Mid Layer 2 Bottom Layer 20158208 20158207 19 201582 Version 5 Revision 2 Print Date/Time: 2011/10/03 14:26:28 www.national.com LM4922 Revision History Rev Date Description 1.0 11/16/05 Initial release. 1.1 11/18/06 Text edits. www.national.com 20 201582 Version 5 Revision 2 Print Date/Time: 2011/10/03 14:26:28 LM4922 Physical Dimensions inches (millimeters) unless otherwise noted 14 - Bump micro SMD Order Number LM4922TL NS Package Number TLE1411A X1 = 1.9700.03mm, X2 = 1.9700.03mm, X3 = 0.6000.075mm, 21 201582 Version 5 Revision 2 Print Date/Time: 2011/10/03 14:26:28 www.national.com LM4922 Ground-Referenced, Ultra Low Noise, Fixed Gain, 80mW Stereo Headphone Amplifier Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise(R) Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise(R) Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2011 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com www.national.com Tel: 1-800-272-9959 National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com 201582 Version 5 Revision 2 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com Print Date/Time: 2011/10/03 14:26:29 National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated