1
CSM_E3C_DS_E_11_1
Compact Head Amplifier-separated Photoelectric Sensor
E3C
Thin, Compact Head Saves Space
and Mounts Closely. Built-in
Interference Protection Provided.
• Input indicator on the Sensor Unit simplifies settings.
Be sure to read Safety Precautions on
page 8.
Ordering Information
Sensors
Sensor Units [Refer to Dimensions on page 9.]
*1. Through-beam Sensors are normally sold in sets that include both the Emitter and Receiver.
*2. You cannot order the Emitter and Receiver with separate model numbers. Always order them together using the model number for the set (E3C-S50 2M).
Sensing method Application Appearance Sensing distance Model
Through-beam
(Emitter + Receiver)
Small type
E3C-S10 2M *1
Emitter E3C-S10L 2M
Receiver E3C-S10D 2M
E3C-S50 2M *1 *2
Emitter E3C-S50L 2M
Receiver E3C-S50D 2M
E3C-1 2M *1
Emitter E3C-1L 2M
Receiver E3C-1D 2M
E3C-2 2M *1
Emitter E3C-2L 2M
Receiver E3C-2D 2M
Slim type
E3C-S20W 2M
E3C-S30W 2M
Side-view E3C-S30T 2M
Diffuse-reflective
Small type E3C-DS10 2M
Slim type E3C-DS5W 2M
Side-view E3C-DS10T 2M
Convergent-reflective Small type E3C-LS3R 2M
Red light Infrared light
10
12
5.8
100 mm
11
13
7
500 mm
25
8
12
1 m
36
16
12.4
2 m
18
12.5
2.8
200 mm
15
8
3
300 mm
7.85
3
15
15
26
10
100 mm
18
19.5
2.8
50 mm
8
21
11
100 mm
10
18
36
30±3 mm
E3C
2
Amplifier Units [Refer to Amplifier Units on page 12.]
Accessories (Order Separately)
Mounting Brackets [Refer to E39-L/E39-S/E39-R for Dimensions.]
Note: Refer to E39-L/E39-S/E39-R for Dimensions.
* When using through-beam models, order one bracket for the Receiver and one for the Emitter.
Power supply Application Appearance Functions Model
DC Slim type E3C-JC4P 2M
60
30
14
Self
diagnostic
Appearance Model Quantity Remarks
E39-L41 2 Provided with the E3C-1.
E39-L42 2Provided with the E3C-2.
Can be used with the E3C-DS10.
E39-L127-T1 1
Can be used with the E3C-S10.E39-L127-T2 1
E39-L127-T3 1
E39-L31 1*Can be used with the E3C-S50.
E3C
3
Ratings and Specifications
Sensors
Sensing method Through-beam
Item Model E3C-S10 E3C-S20W E3C-S50 E3C-S30T
E3C-S30W E3C-1 E3C-2
Sensing distance 100 mm 200 mm 500 mm 300 mm 1 m 2 m
Standard sensing
object Opaque, 2-mm dia. min. Opaque, 3-mm
dia. min.
Opaque, 1.5-mm
dia. min.
Opaque, 4-mm
dia. min.
Opaque, 8-mm
dia. min.
Directional angle Emitter/Receiver: 10 to 60° each Emitter/Receiver: 10 to 40° each Emitter/Receiv-
er: 3 to 20° each
Emitter/Receiv-
er: 3 to 15° each
Light source (wavelength) Infrared LED (950 nm) Infrared LED
(940 nm) Infrared LED (950 nm)
Ambient illuminance
(Receiver side) Incandescent lamp: 3,000 lx max., Sunlight 10,000 lx max.
Ambient temperature range Operating/Storage: −25°C to 70°C (with no icing or condensation)
Ambient humidity range Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. at 500 VDC
Dielectric strength 500 VAC at 50/60 Hz for 1 minute
Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance Destruction: 500 m/s2 for 3 times each in X, Y, and Z directions
Degree of protection
IEC 60529 IP64
Limited to indoor
use
IEC 60529 IP50
Limited to indoor
use
IEC 60529 IP64
Limited to indoor
use
IEC 60529 IP60
Limited to indoor
use
IEC 60529 IP66
Limited to indoor use
Connection method Pre-wired models (standard length: 2 m)
Weight (packed state) Approx. 50 g Approx. 24 g Approx. 60 g Approx. 120 g
Material
Case Polycarbonate ABS Polycarbonate Zinc die-cast
Lens Polycarbonate Acrylics Polycarbonate
Mounting
Brackets --- Steel
Accessories Instruction
manual
Phillips screw
M2×8, spring
washer, flat
washer, M2 nut,
instruction
manual
Instruction
manual
Phillips screw
M2×8, spring
washer, flat
washer, nut M2,
instruction
manual
Mounting
Bracket (with
screws),
instruction
manual
Mounting
Bracket (with
screws),
instruction
manual
Sensing method Diffuse-reflective Convergent-reflective
Item Model E3C-DS5W E3C-DS10T E3C-DS10 E3C-LS3R
Sensing distance 50 mm (White paper 100 ×
100 mm)
100 mm (White paper 100
× 100 mm)
100 mm (White paper 50 ×
50 mm)
30 ± 3 mm (White paper 10
× 10 mm)
Differential travel 20% max. of sensing distance 10% max. ±3% max.
Light source (wavelength) Infrared LED (950 nm) Infrared LED (950 nm) Red LED (680 nm)
Ambient illuminance
(Receiver side) Incandescent lamp: 3,000 lx max., Sunlight 10,000 lx max.
Ambient temperature range Operating/Storage: −25°C to 70°C (with no icing or condensation)
Ambient humidity range Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. at 500 VDC
Dielectric strength 500 VAC at 50/60 Hz for 1 minute
Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance Destruction: 500 m/s2 for 3 times each in X, Y, and Z directions
Degree of protection IEC 60529 IP50 (Limited to indoor use) IEC 60529 IP64 (Limited to indoor use)
Connection method Pre-wired models (standard length: 2 m)
Weight (packed state) Approx. 50 g Approx. 55 g
Material Case Polycarbonate
Lens Polycarbonate
Accessories
Phillips screw M2×8,
spring washer, flat washer,
M2 nut, instruction manual
Instruction manual
E3C
4
Amplifier Units
Item Model E3C-JC4P
Power supply
voltage 12 to 24 VDC±10%, ripple (p-p): 1 V max.
Power (current)
consumption 50 mA max.
Control output
Load power supply voltage: 24 VDC max., load current: 100 mA max., NPN open collector output type (residual voltage:
1 V max.)
Light-ON/Dark-ON switch selectable
Timer function OFF-delay 0/40 ms (switch selectable)
Ambient temperature range Operating: −10° to 55°C, Storage: −25° to 70°C (with no icing or condensation)
Ambient humidity range Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. at 500 VDC
Dielectric strength 500 VAC at 50/60 Hz for 1 minute
Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance Destruction: 300 ms2 three times in each of X, Y and Z directions
Degree of protection IEC IP60 (limited to indoor use)
Protection Reverse polarity protection, output short-circuit protection, mutual interference prevention
Response time Operate or reset: 1 ms max.
Connection method Terminal block input cable pullout (standard cable length: 2 m)
Weight
(packed state) Approx. 80 g
Material Case ABS
Mounting Brackets Iron
Accessories Mounting Bracket, Adjustment screwdriver, Caution label, Instruction manual
E3C
5
Engineering Data (Reference Value)
Parallel Operating Range
Through-beam Through-beam Through-beam
E3C-S10 E3C-S20W E3C-S50
Through-beam Through-beam Through-beam
E3C-1 E3C-2 E3C-S30T/-S30W
Operating Range
Diffuse-reflective Diffuse-reflective Diffuse-reflective
E3C-DS5W E3C-DS10T E3C-DS10 (Example 1)
Y
X
200
150
100
50
0
−50
−100
−150
−200
Sensing
distance X (mm)
50 100 150 200 250 300
Operating position Y (mm)
Y
X
200
150
100
50
0
−50
−100
−150
−200
50 100 150 200 250 300
Sensing
distance X (mm)
Operating position Y (mm)
Y
X
0.2 0.4 0.6 0.8
1
200
150
100
50
0
−50
−100
−150
−200
Sensing
distance X (mm)
Operating position Y (mm)
Y
X
0.5 1 1.5 2
200
150
100
50
0
−50
−100
−150
−200
Sensing
distance X (mm)
Operating position Y (mm)
Y
X
200
150
100
50
0
−50
−100
−150
−200
1 2 3 4
Sensing
distance X (mm)
Operating position Y (mm)
200
150
100
50
0
−50
−100
−150
−200
200 400 600 800
Y
X
Sensing
distance
X (mm)
Operating position Y (mm)
Moving direction
of object
X
Y
40
30
20
10
0
−10
−20
−30
−40
20 40 60 80 120
100
Sensing
distance
X (mm)
Operating position Y (mm)
Y
X
40
30
20
10
0
−10
−20
−30
−40
20 40 60 80 100 120 160
140
Sensing
distance
X (mm)
Operating position Y (mm)
X
Optical
axis
Y
40
30
20
10
0
−10
−20
−30
−40
40 80 120 200
160
ON
OFF
Moving
direction
of object
Sensing
distance
X (mm)
Operating position Y (mm)
E3C
6
Diffuse-reflective Convergent-reflective Convergent-reflective
E3C-DS10 (Example 2) E3C-LS3R (Example 1) E3C-LS3R (Example 2)
Excess Gain vs. Set Distance
E3C-S20W E3C-S30T/-S30W E3C-S50
E3C-DS5W E3C-DS10T E3C-LS3R
X
Y
40
30
20
10
0
−10
−20
−30
−40
40 80 120
160
200
ON
OFF
Optical
axis
Moving direction
of object
Sensing
distance
X (mm)
Operating position Y (mm)
X
Y
2
1
0
−1
−2
22 26 28 30 32 34 36 38
ON
OFF
24
Optical
axis
Sensing distance
X (mm)
Operating position Y (mm)
Moving direction
of object
X
Y
2
1
0
−1
−2
22 26 28 30 32 34 3836
ON
OFF
24
Optical
axis
Moving
direction
of object
Sensing distance
X (mm)
Operating position Y (mm)
100
70
50
30
10
7
5
3
1
0.7
0.5
0.3
0.1
0 100 200 300 400 500
Set distance (mm)
Operating Level
Excess Gain ratio
100
70
50
30
10
7
5
3
1
0.7
0.5
0.3
0.1
0 0.2 0.4 0.6 0.8 1
Excess Gain ratio
Operating Level
Set distance (mm)
100
70
50
30
10
7
5
3
1
0.7
0.5
0.3
0.1
0 0.2 0.4 0.6 0.8
1
Excess Gain ratio
Operating Level
Set distance (mm)
100
70
50
30
10
7
5
3
1
0.7
0.5
0.3
0.1
0 50 100 150 200
Excess Gain ratio
Operating Level
Set distance (mm)
0 50 100 150 200
100
70
50
30
10
7
5
3
1
0.7
0.5
0.3
0.1
Excess Gain ratio
Operating Level
Set distance (mm)
100 20304050
100
70
50
30
10
7
5
3
1
0.7
0.5
0.3
0.1
Excess Gain ratio
Operating Level
Set distance (mm)
E3C
7
I/O Circuit Diagrams
NPN output
Connection
Nomenclature/Settings
Model Operation
mode Timing charts Operation
selector Output circuit
E3C-JC4P
Light-ON L-ON
(LIGHT ON)
Dark-ON D-ON
(DARK ON)
Amplifier Units Connected to the through-beam model Connected to the reflective model Note
E3C-JC4P
Note: 1. The strip-off length of the
shielded cable should
always be 20 mm max. on
the Receiver side (white)
and 50 mm max. on the
Emitter side (red).
Incident light
No incident light
ON
OFF
ON
OFF
ON
OFF
Light
indicator
(red)
Output
transistor
Load
(relay etc.)
40 ms
Light
indicator
(red)
Stability
indicator
(green)
Photo-
electric
Sensor
Main
Circuit
Load
Brown
Black
Blue
Pink
Self diagnostic output
50 mA max.
Output
12 to 24 VDC
0 V
100 mA max.
Z
0
Z
1
40 ms
Incident light
No incident light
ON
OFF
ON
OFF
ON
OFF
Light
indicator
(red)
Output
transistor
Load
(relay etc.)
Shield
Emitter Receiver
White
Red
Shield
Emitter/receive
r
Shield
White
Red
Shield
Amplifier Units Nomenclature
E3C-JC4P
Light indicator
(red)
Stability indicator
(green)
Sensitivity adjuster
(4-turn endless asjuster)
Operation selector
E3C
8
Safety Precautions
Refer to Warranty and Limitations of Liability.
This product is not designed or rated for ensuring
safety of persons either directly or indirectly.
Do not use it for such purposes.
Do not use the product in atmospheres or environments that exceed
product ratings.
● Wiring
Connection of Amplifier Unit and Sensor
Always run the shielded wires of the Emitter and Receiver separately.
Also, route the sensor cable along the cable grooves of the cover and
sensor and fix it with the cover.
● Wiring
Extension Cable
•The extension distance of the sensor connection cable should be
within 10 m including sensor cable.
•The strip-off length of the core in the connection cable should be 20
mm max. on the Receiver side and 50 mm max. on the Emitter side,
and the core should be as short as possible. Avoid using the joint
terminal and connector.
•Use independent shielded wires for the Emitter and Receiver.
Using a common shielded wire can cause a malfunction.
Extension Cable
Through-beam
Reflective model
● Others
When the E3C is used in a place where high-frequency noise will be
generated, e.g. ultrasonic welder, grounding the 0-V terminal (on the
shield side of the connection cable) of the Receiver may avoid a
malfunction caused by induction.
WARNING
Precautions for Correct Use
Amplifier Units
Sensor Units
Receiver
Emitter
White (Shield)
(Shield) Red
20 mm max.
Socket
Cable Specified cable Replacement
cable
Model
E3C-S10
E3C-1
E3C-2
E3C-S50
Polyethylene insulation shield
Round cable
1-conductor shield/
vinyl wire, conduc-
tor cross section:
0.3 mm2 min.
E3C-S20W
Vinyl insulation shield round cable
1-conductor shield/
vinyl wire, conduc-
tor cross section:
0.3 mm2 min.
E3C-S30T
E3C-S30W
Vinyl insulation shield round cable
(robot cable)
Cable Specified cable Replacement
cable
Model
E3C-DS10
E3C-DS10T
E3C-VS1G
E3C-VS3R
E3C-LS3R
Vinyl insulation shielded parallel ca-
ble
When there is no1-
conductor shielded,
vinyl cable (parallel
wire), use two 1-
conductor shielded,
vinyl wires.
E3C-DS5W
E3C-VS7R
E3C-VM35R
Vinyl insulation shielded parallel ca-
ble When there is no1-
conductor shielded,
vinyl cable (parallel
wire), use two 1-
conductor shielded,
vinyl wires.
2.4 dia.
12-conductor, 0.18 dia.
White (polyethylene)
Shield
White
(vinyl)
Gray (vinyl sheath)
Shield
1.7 dia.
12-conductor, 0.18 dia.
Sheath
Shield
Polyethylene
Conductor
1.8 dia.
30-conductor, 0.08 dia.
Sheath
Shield
Polyethylene
Conductor
12-conductor, 0.18 dia.
Sheath
Shield
Conductor
Polyethylene
Internal
sheath
2.4
4.3
Sheath
Shield
Polyethylene
Conductor
7-conductor, 0.18 dia.
E3C
9
Dimensions
Sensors
Sensor Units
(Unit: mm)
Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified.
E3C-S10
Emitter: E3C-S10L
Receiver: E3C-S10D
5.8 10
2.3
2.8
2.87.5
Two, 2.9 dia.
2.4-dia. shielded cable with 1 conductor
(Conductor cross section: 0.3 mm2),
Standard len
g
th: 2 m
Light indicator (red)
(emitter only)
12
2
5.2 dia.
Emitter/
receiver surface
E3C-S50
Emitter: E3C-S50L
Receiver: E3C-S50D
13
7
Emitter/receiver label
Two, 3.2 dia.
3.5
5.7 dia.
8
±0.2
2.9
±0.2
11
Emitter/receiver
surface
2.4-dia. shielded cable with 1 conductor
(Conductor cross section: 0.3 mm2),
Standard length: 2 m
Light indicator (red)
(emitter only)
E3C-1
Emitter: E3C-1L
Receiver: E3C-1D
13.5
12
Optical axis position
Emitter/receiver
surface
Iron
12.5
* Mounting Bracket can be attached to side A.
5
103
8 6.4
5.5
2
13
25
3.2
8
12
6 dia.
3.2
16.5
5
4M3
6
3.5
Lens 4 dia.
12
(A)*
2.4-dia. shielded cable with 1 conductor
(Conductor cross section: 0.3 mm2), Standard length: 2 m
Light indicator (red)
(emitter only)
Lens 8 dia.
6.7
23
3.2
5.5
4.5
Iron
3.2
36
12.4 9.4
2
8
12
8 dia.
7
21
Emitter/receiver
surface
13.3 20
17
3.3
* Mounting Bracket can be attached to side A.
(A)*
16
M3 2.4-dia. shielded cable with 1 conductor
(conductor cross section: 0.3 mm
2
), Standard length: 2 m
Optical
axis position
Light indicator (red)
(emitter only)
E3C-2
Emitter: E3C-2L
Receiver: E3C-2D
E3C
10
E3C-S20W
3.8 dia.
11
±0.2
3.5
2.5
2 dia. (emitter)
Light indicator (red) (Red)(white)
54
4.5 4.5
3.6
18 2 dia. (receiver)
2
2,000
(6) 12.5
2.81.4
2.3 dia.
1.75-dia. shielded cable
with 1 conductor
(Conductor cross section:
0.3 mm2),
Standard length: 2 m
Receiver Emitter
Emitter: E3C-S20LW
Receiver: E3C-S20DW
E3C-S30W
2.2
dia.
4
3.6 dia.
5
7.5
12
2.2
2
8
15
1.5 dia. (receiver)
3
1.5
5
2.4 1.5 dia. (emitter)
1.93-dia. shielded robotics
cable with 1 conductor
(Conductor cross section:
0.15 mm
2
),
Standard length: 2 m
Receiver Emitter
Light indicator
(red) 1.2 dia.
Emitter: E3C-S30LW
Receiver: E3C-S30DW
E3C-S30T
2.2
dia.
15
3.85
5
1.5 dia. (receiver)
3.6 dia.
12
7.5
2.2
7.85
1.5 dia. (emitter)
3
1.5
5
2.4
1.93-dia. shielded robotics
cable with 1 conductor
(Conductor cross section:
0.15 mm2),
Standard length: 2 m
Receiver Emitter
Light indicator
(red) 1.2 dia.
Emitter: E3C-S30LT
Receiver: E3C-S30DT
4
5
Optical axis
position
3.2 10
2.4
6.6
19
3.2
3.9
Receiver
Emitter
Lens
5
1094.3
26 2
8.5±1
15
R3.3
R1.2
2.4-dia. shielded cable
with 2 conductors
(Conductor cross section: 0.3 mm2),
Standard length: 2 m
Light indicator
(red)
E3C-DS10
E3C
11
3.5
2.5
Emitter
Receiver
4
7
±0.2
6
19.5
3.8 dia.
2.8
1.4
2.3 dia.
18
2,000
2
4.5
11
±0.2
40
4
7
1.8 × 3.6-dia. shielded
cable with 2 conductors
(Conductor cross
section: 0.18 mm2),
Standard length: 2 m
E3C-DS5W
E3C-DS10T
16±0.2 Two, 3.2-dia. mounting holes
2.5
Emitter Receiver
2.5
86
40
77±0.2
11
21
1.5
2,000
4.
6
2.4-dia. shielded cable with 2 conductors
(Conductor cross section: 0.3 mm2),
Standard length: 2 m
E3C-LS3R
Emitter Receiver
36 2
1094.3
3.2
6.5
313
±1
Lens
30
Optical axis
position
Light indicator
(red)
5.3
18
2.4
6.6
13
R3.3
R1.2
2.4-dia. shielded cable with 2 conductors
(Conductor cross section: 0.3 mm2),
Standard length: 2 m
E3C
12
Amplifier Units
Accessories (Order Separately)
Mounting Brackets
Refer to E39-L/E39-S/E39-R for details.
E3C-JC4P
50
(10)
5
Two, 3.3 dia.
Operation selector
Caution label*
Sensitivity adjuster
Light indicator
M2.6 Stability indicator
Timer mode selector switch
60
16 R1.6
Mounting bracket (iron) (detachable)
23.5
4310
6
14
12
3.5
30
2.5
35.5
2
3.2
14
*After adjusting the sensitivity, attach the caution label at the location indicated by
above to prevent malfunction.
4.5-dia. vinyl-insulated round cable with
4 conductors (Conductor cross section:
0.2mm2, Insulator diameter: 1.2mm),
Standard length: 2 m
With Mounting Bracket Attached
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
2014.4
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2014 All Right Reserved.
