w WM8986 Multimedia DAC with Class D Headphone and Line Out DESCRIPTION FEATURES The WM8986 is a low power, high quality, feature-rich stereo DAC designed for portable multimedia applications that require low power consumption and high quality audio. Stereo DAC: * DAC SNR 100dB, THD -86dB (`A' weighted @ 48kHz) * Headphone driver with `capless' option - 40mW/channel output power into 16 / 3.3V AVDD2 - Class D headphone driver - Class AB headphone / line Driver - PSRR 70dB at 217Hz * Stereo, mono or differential line output The device integrates preamps for stereo differential mics, and includes class D and class AB drivers for headphone and differential or stereo line output. External component requirements are reduced as no separate microphone or headphone amplifiers are required. Advanced DSP features include a 5-band equaliser and a digital playback limiter. Highly flexible mixers enable many new application features, with the option to playback any combination of voice, line inputs and digital audio such as FM Radio or MP3. The WM8986 digital audio interface can operate in master or slave mode, while an integrated PLL provides flexible clocking schemes. The WM8986 operates at analogue supply voltages from 2.5V to 3.3V, although the digital core can operate at voltages down to 1.71V to save power. Additional power management control enables individual sections of the chip to be powered down under software control. Mic Preamps: * Stereo differential or mono microphone interfaces * Programmable preamp gain * Pseudo differential inputs with common mode rejection Other Features: * Enhanced 3-D function for improved stereo separation * Digital playback limiter * 5-band Equaliser * Aux inputs for stereo analog input signals or `beep' * PLL supporting various clocks between 8MHz-50MHz * Sample rates supported (kHz): 8, 11.025, 16, 12, 16, 22.05, 24, 32, 44.1, 48 * Low power, low voltage * 2.5V to 3.6V analogue supplies * 1.71V to 3.6V digital supplies * 4x4mm 28-lead COL QFN package APPLICATIONS * * WOLFSON MICROELECTRONICS plc To receive regular email updates, sign up at http://www.wolfsonmicro.com/enews/ Portable audio player / FM radio Multimedia Mobile Handsets Production Data, June 2009, Rev 4.1 Copyright (c)2008 Wolfson Microelectronics plc WM8986 Production Data BLOCK DIAGRAM w PD, Rev 4.1, June 2009 2 WM8986 Production Data TABLE OF CONTENTS DESCRIPTION ....................................................................................................... 1 FEATURES............................................................................................................. 1 APPLICATIONS ..................................................................................................... 1 BLOCK DIAGRAM ................................................................................................. 2 TABLE OF CONTENTS ......................................................................................... 3 PIN CONFIGURATION ........................................................................................... 4 ORDERING INFORMATION .................................................................................. 4 PIN DESCRIPTION ................................................................................................ 5 ABSOLUTE MAXIMUM RATINGS ......................................................................... 6 RECOMMENDED OPERATING CONDITIONS ..................................................... 6 ELECTRICAL CHARACTERISTICS ...................................................................... 7 TERMINOLOGY .......................................................................................................... 11 AUDIO PATHS OVERVIEW ................................................................................. 12 SIGNAL TIMING REQUIREMENTS ..................................................................... 14 SYSTEM CLOCK TIMING ........................................................................................... 14 AUDIO INTERFACE TIMING - MASTER MODE ........................................................ 14 AUDIO INTERFACE TIMING - SLAVE MODE ............................................................ 15 CONTROL INTERFACE TIMING - 3-WIRE MODE .................................................... 16 CONTROL INTERFACE TIMING - 2-WIRE MODE .................................................... 17 INTERNAL POWER ON RESET CIRCUIT .......................................................... 18 RECOMMENDED POWER UP/DOWN SEQUENCE .................................................. 20 DEVICE DESCRIPTION ....................................................................................... 22 INTRODUCTION ......................................................................................................... 22 INPUT SIGNAL PATH ................................................................................................. 23 OUTPUT SIGNAL PATH ............................................................................................. 31 3D STEREO ENHANCEMENT .................................................................................... 37 ANALOGUE OUTPUTS............................................................................................... 37 DIGITAL AUDIO INTERFACES ................................................................................... 50 AUDIO SAMPLE RATES ............................................................................................. 54 MASTER CLOCK AND PHASE LOCKED LOOP (PLL) ............................................... 55 COMPANDING ............................................................................................................ 58 GENERAL PURPOSE INPUT/OUTPUT ...................................................................... 60 OUTPUT SWITCHING (JACK DETECT)..................................................................... 61 CONTROL INTERFACE .............................................................................................. 62 RESETTING THE CHIP .............................................................................................. 63 POWER SUPPLIES .................................................................................................... 63 POWER MANAGEMENT ............................................................................................ 64 REGISTER MAP................................................................................................... 65 REGISTER BITS BY ADDRESS ................................................................................. 67 DAC DIGITAL FILTER CHARACTERISTICS ...................................................... 80 TERMINOLOGY .......................................................................................................... 80 DAC FILTER RESPONSES......................................................................................... 81 5-BAND EQUALISER .................................................................................................. 82 APPLICATIONS INFORMATION ......................................................................... 86 RECOMMENDED EXTERNAL COMPONENTS .......................................................... 86 PACKAGE DIAGRAM .......................................................................................... 87 IMPORTANT NOTICE .......................................................................................... 88 ADDRESS: .................................................................................................................. 88 w PD, Rev 4.1, June 2009 3 WM8986 Production Data PIN CONFIGURATION ORDERING INFORMATION ORDER CODE TEMPERATURE RANGE PACKAGE MOISTURE SENSITIVITY LEVEL PEAK SOLDERING TEMPERATURE WM8986GECO/V -40C to +85C 28-lead COL QFN (4 x 4 mm) (Pb-free) MSL3 260oC WM8986GECO/RV -40C to +85C 28-lead COL QFN (4 x 4 mm) (Pb-free, tape and reel) MSL3 260oC Note: Reel quantity = 3,500 w PD, Rev 4.1, June 2009 4 WM8986 Production Data PIN DESCRIPTION PIN NAME TYPE 1 LIP Analogue input DESCRIPTION 2 LIN Analogue input Left MIC pre-amp negative input 3 RIP Analogue input Right MIC pre-amp positive input 4 RIN Analogue input 5 DACDAT Digital Input 6 LRC Digital Input / Output DAC sample rate clock 7 BCLK Digital Input / Output Digital audio bit clock 8 MCLK Digital Input 9 DGND Supply Digital ground 10 DCVDD Supply Digital core logic supply Left MIC pre-amp positive input Right MIC pre-amp negative input DAC digital audio data input Master clock input 11 DBVDD Supply 12 CSB/GPIO1 Digital Input / Output 13 SCLK Digital Input 3-Wire control interface clock input / 2-wire control interface clock input 14 SDIN Digital Input / Output 3-Wire control interface data input / 2-Wire control interface data input 15 MODE Digital Input 16 AUXL Analogue input Left auxiliary input 17 AUXR Analogue input Right auxiliary input 18 OUT4 Analogue Output Right line output / mono mix output 19 OUT3 Analogue Output Left line output 20 ROUT2 Analogue Output Class D or class AB headphone output right 21 AGND2 Supply 22 LOUT2 Analogue Output 23 AVDD2 Supply 24 VMID Reference 25 AGND1 Supply 26 ROUT1 Analogue Output Class AB headphone or line output right 27 LOUT1 Analogue Output Class AB headphone or line output left 28 AVDD1 Supply w Digital buffer (I/O) supply 3-Wire control interface chip Select / GPIO1 pin Control interface selection Analogue ground (ground reference for ROUT2/LOUT2 and OUT3/OUT4) Class D or class AB headphone output left Analogue supply (feeds output amplifiers ROUT2/LOUT2 and OUT3/OUT4) Decoupling for DAC reference voltage Analogue ground (ground reference for all input amplifiers, PLL, DAC, interna bias circuits, output amplifiers LOUT1, ROUT1) Analogue supply (feeds all input amplifiers, PLL, DAC, internal bias circuits, output amplifiers LOUT1, ROUT1) PD, Rev 4.1, June 2009 5 WM8986 Production Data ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are stress ratings only. Permanent damage to the device may be caused by continuously operating at or beyond these limits. Device functional operating limits and guaranteed performance specifications are given under Electrical Characteristics at the test conditions specified. ESD Sensitive Device. This device is manufactured on a CMOS process. It is therefore generically susceptible to damage from excessive static voltages. Proper ESD precautions must be taken during handling and storage of this device. Wolfson tests its package types according to IPC/JEDEC J-STD-020B for Moisture Sensitivity to determine acceptable storage conditions prior to surface mount assembly. These levels are: MSL1 = unlimited floor life at <30C / 85% Relative Humidity. Not normally stored in moisture barrier bag. MSL2 = out of bag storage for 1 year at <30C / 60% Relative Humidity. Supplied in moisture barrier bag. MSL3 = out of bag storage for 168 hours at <30C / 60% Relative Humidity. Supplied in moisture barrier bag. The Moisture Sensitivity Level for each package type is specified in Ordering Information. CONDITION MIN MAX -0.3V +4.5V Voltage range digital inputs DGND -0.3V DBVDD +0.3V Voltage range analogue inputs AGND1 -0.3V AVDD1 +0.3V Operating Temperature Range -40C +85C DBVDD, DCVDD, AVDD1, AVDD2 supply voltages Storage temperature prior to soldering 30C max / 85% RH max Storage temperature after soldering -65C +150C Notes: 1. Analogue and digital grounds must always be within 0.3V of each other. 2. All digital and analogue supplies are internally independent (i.e. not connected). 3. Analogue supply voltages AVDD1 and AVDD2 should be greater than or equal to the DCVDD digital supply voltage. 4. DBVDD must be greater than or equal to DCVDD. RECOMMENDED OPERATING CONDITIONS PARAMETER SYMBOL Digital supply range (Core) DCVDD 1.711 3.6 V Digital supply range (Buffer) DBVDD 1.71 3.6 V AVDD1, AVDD2 2.51 Analogue supply range Ground TEST CONDITIONS DGND, AGND1, AGND2 MIN TYP MAX 3.6 0 UNIT V V Notes: 1. Analogue supply voltages should not be less than digital supply voltages. 2. DBVDD must be greater than or equal to DCVDD. w PD, Rev 4.1, June 2009 6 WM8986 Production Data ELECTRICAL CHARACTERISTICS Test Conditions DCVDD=1.8V, AVDD1=AVDD2=DBVDD=3.3V, TA = +25oC, 1kHz signal, fs = 48kHz, 24-bit audio data unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Microphone Input PGA Inputs (LIP, LIN, RIP, RIN) INPPGAVOLL, INPPGAVOLR, PGABOOSTL and PGABOOSTR = 0dB Full-scale Input Signal Level - Single-ended input via LIN/RIN 1 AVDD/3.3 Vrms Full-scale Input Signal Level - Pseudo-differential input 1,2 AVDD*0.7/ 3.3 Vrms INPPGAVOLL/R = +35.25dB No input signal 0 to 20kHz 150 V LIN, RIN input resistance INPPGAVOLL and INPPGAVOLR = +35.25dB 1.6 k LIN, RIN input resistance INPPGAVOLL and INPPGAVOLR = 0dB 46 k LIN, RIN input resistance INPPGAVOLL and INPPGAVOLR = -12dB 71 k LIP, RIP input resistance All gain settings 90 k Input PGA equivalent input noise Input Capacitance All analogue input pins 10 pF Input PGA Programmable Gain Gain adjusted by INPPGAVOLL and INPPGAVOLL Programmable Gain Step Size Guaranteed monotonic 0.75 dB INPPGAMUTEL and INPPGAMUTER = 1 100 dB Input Gain Boost PGABOOSTL and PGABOOSTR = 0 0 dB Input Gain Boost PGABOOSTL and PGABOOSTR = 1 +20 dB Input PGA Mute Attenuation -12 +35.25 dB Auxiliary Analogue Inputs (AUXL, AUXR) Full-scale Input Signal Level 2 Input Resistance Input Capacitance Gain range from AUXL and AUXR input to left and right input PGA mixers AUXLBOOSTVOL and AUXRBOOSTVOL step size w AVDD/3.3 Vrms Left Input boost and mixer enabled, at +6dB 11 k Left Input boost and mixer enabled, at 0dB gain 22 k Left Input boost and mixer enabled, at -12dB gain 60 k Right Input boost, mixer enabled, at +6dB gain 11 k Right Input boost, mixer enabled, at 0dB gain 22 k Right Input boost, mixer enabled, at -12dB gain 60 k 10 All analogue Inputs Gain adjusted by AUXL2BOOSTVOL and AUXR2BOOSTVOL pF +6 -12 3 dB dB PD, Rev 4.1, June 2009 7 WM8986 Production Data Test Conditions DCVDD=1.8V, AVDD1=AVDD2=DBVDD=3.3V, TA = +25oC, 1kHz signal, fs = 48kHz, 24-bit audio data unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT DAC to left and right mixers into 10k / 50pF load on LOUT1 and ROUT1 LOUT1VOL, ROUT1VOL, DACLVOL and DACRVOL = 0dB Full-scale output 1 LOUT1VOL and ROUTVOL = 0dB Signal to Noise Ratio 3 Total Harmonic Distortion 4 Total Harmonic Distortion + Noise 5 SNR THD THD+N Channel Separation 6 AVDD1/3.3 Vrms 100 dB A-weighted AVDD1=AVDD2=2.5V 96 dB 22Hz to 20kHz AVDD1=AVDD2=3.3V 95.5 dB 22Hz to 20kHz AVDD1=AVDD2=2.5V 93.5 dB 0dBFS input AVDD1=AVDD2=3.3V -86 0dBFS input AVDD1=AVDD2=2.5V -86 0dBFS input AVDD1=AVDD2=3.3V -84 0dBFS input AVDD1=AVDD2=2.5V -84 dBFS 1kHz signal 100 dB AVDD1/3.3 Vrms 100 dB A-weighted AVDD1=AVDD2=2.5V 96 dB 22Hz to 20kHz AVDD1=AVDD2=3.3V 95.5 dB 22Hz to 20kHz AVDD1=AVDD2=2.5V 93.5 dB 0dBFS input AVDD1=AVDD2=3.3V -86 0dBFS input AVDD1=AVDD2=2.5V -82 0dBFS input AVDD1=AVDD2=3.3V -84 0dBFS input AVDD1=AVDD2=2.5V -80 dBFS 1kHz input signal 100 dB A-weighted AVDD1=AVDD2=3.3V 90 -80 dBFS dBFS -78 dBFS DAC to L/R mixer into 10k / 50pF load on L/ROUT2, class AB mode LOUT2VOL, ROUT2VOL, DACLVOL and DACRVOL = 0dB Full-scale output 1 LOUT2VOL and ROUT2VOL = 0dB Signal to Noise Ratio 3 Total Harmonic Distortion 4 Total Harmonic Distortion + Noise 5 SNR THD THD+N Channel Separation 6 A-weighted AVDD1=AVDD2=3.3V 90 -80 dBFS dBFS -78 dBFS DAC to OUT3 and OUT4 mixers to OUT3/OUT4 outputs into 10k / 50pF load. DACVOLL and DACVOLR = 0dB Full-scale output voltage Signal to Noise Ratio 3 Total Harmonic Distortion 4 Total Harmonic Distortion + Noise 5 w AVDD2/3.3 Vrms 100 dB 22Hz to 22kHz AVDD1=AVDD2=3.3V 96 dB THD full-scale signal AVDD1=AVDD2=3.3V -87 -80 dBFS THD+N full-scale signal AVDD1=AVDD2=3.3V -85 -78 dBFS full-scale signal -80 SNR A-weighted AVDD1=AVDD2=3.3V 90 dBFS PD, Rev 4.1, June 2009 8 WM8986 Production Data Test Conditions DCVDD=1.8V, AVDD1=AVDD2=DBVDD=3.3V, TA = +25oC, 1kHz signal, fs = 48kHz, 24-bit audio data unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT AVDD1=AVDD2=2.5V Channel Separation 6 1kHz signal 100 dB DAC to left and right mixer into headphone (16 load on LOUT1 and ROUT1 LOUT1VOL, ROUT1VOL, DACLVOL and DACRVOL = 0dB Full-scale output Signal to Noise Ratio 3 Total Harmonic Distortion 4 Total Harmonic Distortion + Noise 5 AVDD1/3.3 Vrms A-weighted 100 dB 22Hz to 20kHz 95.5 dB THD Po = 20mW, RL=16 -75 dB THD+N Po = 20mW, RL=16 -75 dB 1kHz signal 100 dB SNR Channel Separation 6 DAC to left and right mixer into headphone (16 load) on LOUT2 and ROUT2, Class AB mode LOUT2VOL, ROUT2VOL, DACLVOL and DACRVOL = 0dB Full-scale output Signal to Noise Ratio 3 Total Harmonic Distortion 4 Total Harmonic Distortion + Noise 5 SNR A-weighted 90 AVDD1/3.3 Vrms 97 dB 22Hz to 20kHz 95.5 THD Po = 20mW, RL=16 -84 -75 dB THD+N Po = 20mW, RL=16 -81 -70 dB 1kHz signal 100 Channel Separation 6 dB dB DAC to left and right mixer into headphone load on LOUT2 and ROUT2, Class D mode, Lfilter = 33uH Cfilter = 220nf LOUT2VOL, ROUT2VOL, DACLVOL and DACRVOL = 0dB Full-scale output L/ROUT2VOL = 0dB Signal to Noise Ratio 3 SNR A-weighted Total Harmonic Distortion 4 THD Po = 20mW, RL=16 THD+N AVDD1/3.3 80 Vrms 90 dB -78 -70 dB Po = 20mW, RL=16 -74 -70 dB 1kHz signal 100 dB PWM Rise Time 1.5 ns PWM Fall Time 1.5 ns DCLKDIV = 1000 1.4 MHz RL = 16, tPW = 20ns, PO = 20mW 72 % 100mVpp ripple @217Hz injected on AVDD2 70 dB No analogue output signal on either channel 0.5 mA Total Harmonic Distortion + Noise 5 Channel Separation 6 PWM Switching Frequency Efficiency Power Supply Rejection Idle Current PSRR PGA outputs to left and right output mixers. BYPL2LMIX = 1 and BYPR2RMIX = 1 PGA gain range into mixer Gain adjusted by BYPLMIXVOL and BYPRMIXVOL -15 BYPLMIXVOL and BYPRMIXVOL gain step into mixer Mute attenuation BYPL2LMIX = 0 BYPR2RMIX = 0 0 +6 dB 3 dB 100 dB Analogue outputs (LOUT1, ROUT1, LOUT2, ROUT2) Programmable Gain range Programmable Gain step size Mute attenuation w Gain adjusted by L/ROUT1VOL and L/ROUT2VOL -57 0 +6 dB Monotonic 1 dB 1kHz, full scale signal L/ROUT1MUTE = 1 L/ROUT2MUTE = 1 85 dB PD, Rev 4.1, June 2009 9 WM8986 Production Data Test Conditions DCVDD=1.8V, AVDD1=AVDD2=DBVDD=3.3V, TA = +25oC, 1kHz signal, fs = 48kHz, 24-bit audio data unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT AUXL and AUXR into on OUT3/OUT4 outputs on 10k / 50pF load INPPGAVOLL, INPPGAVOLR = 0dB Full-scale output voltage, 0dB gain Signal to Noise Ratio 3 Total Harmonic Distortion AVDD2/3.3 Vrms 98 dB A-weighted AVDD1=AVDD2=2.5V 96 dB 22Hz to 22kHz AVDD1=AVDD2=3.3V 95.5 dB 22Hz to 22kHz AVDD1=AVDD2=2.5V 93.5 dB full-scale signal AVDD1=AVDD2=3.3V -90 full-scale signal AVDD1=AVDD2=2.5V -82 full-scale signal AVDD1=AVDD2=3.3V -86 full-scale signal AVDD1=AVDD2=2.5V -80 dB 100 dB AVDD1/3.3 Vrms 100 dB A-weighted AVDD1=AVDD2=2.5V 96 dB 22Hz to 22kHz AVDD1=AVDD2=3.3V 95.5 dB 22Hz to 22kHz AVDD1=AVDD2=2.5V 93.5 dB THD Po = 20mW, RL=16 AVDD1=AVDD2=3.3V -87 -73 dB THD+N Po = 20mW, RL=16 AVDD1=AVDD2=3.3V -85 -70 dB 1kHz full scale signal 100 dB SNR 4 THD Total Harmonic Distortion + Noise 5 THD+N A-weighted AVDD1=AVDD2=3.3V 85 Channel Separation 6 -80 dB dB -78 dB LIN and RIN into input PGA into LOUT1 and ROUT1 into 16 / 50pF loads BYPLMIXVOL, BYPRMIXVOL, LOUT1VOL and ROUT1VOL = 0dB Full-scale output voltage, 0dB gain Signal to Noise Ratio 3 SNR Total Harmonic Distortion 4 Total Harmonic Distortion + Noise 5 Channel separation 6 A-weighted AVDD1=AVDD2=3.3V 85 LIN and RIN into input PGA into OUT3 and OUT4 into 10k / 50pF loads INPPGAVOLL, INPPGAVOLR = 0dB Full-scale output voltage Signal to Noise Ratio 3 Total Harmonic Distortion 4 Total Harmonic Distortion + Noise Channel Separation 6 w 5 AVDD2/3.3 Vrms SNR A-weighted AVDD1=AVDD2=3.3V 100 dB SNR 22Hz to 22kHz AVDD1=AVDD2=3.3V 95.5 dB THD full-scale signal AVDD1=AVDD2=3.3V -87 dB THD+N full-scale signal AVDD1=AVDD2=3.3V -85 dB 1kHz signal 100 dB PD, Rev 4.1, June 2009 10 WM8986 Production Data Test Conditions DCVDD=1.8V, AVDD1=AVDD2=DBVDD=3.3V, TA = +25oC, 1kHz signal, fs = 48kHz, 24-bit audio data unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Digital Input / Output Input HIGH Level VIH Input LOW Level VIL Output HIGH Level VOH Output LOW Level VOL Input Capacitance Input leakage 0.7xDBV DD V 0.3xDBVDD IOL=1mA 0.9xDBV DD V IOH-1mA All digital pins V 0.1xDBVDD V 10 pF 11 pA TERMINOLOGY 1. 2. 3. 4. 5. 6. Full-scale input and output levels scale in relation to AVDD or AVDD2 depending upon the input or output used. For example, when AVDD = 3.3V, 0dBFS = 1Vrms (0dBV). When AVDD < 3.3V the absolute level of 0dBFS will decrease with a linear relationship to AVDD. Input level to RIP and LIP in differential configurations is limited to a maximum of -3dB or performance will be reduced. Signal-to-noise ratio (dBFS) - SNR is the difference in level between a reference full scale output signal and the device output with no signal applied. This ratio is also called idle channel noise. (No Auto-zero or Automute function is employed in achieving these results). Total Harmonic Distortion (dBFS) - THD is the difference in level between a reference full scale output signal and the first seven odd harmonics of the output signal. To calculate the ratio, the fundamental frequency of the output signal is notched out and an RMS value of the next seven harmonics is calculated. Total Harmonic Distortion plus Noise (dBFS) - THD+N is the difference in level between a reference full scale output signal and the sum of the harmonics, wide-band noise and interference on the output signal. To calculate the ratio, the fundamental frequency of the output signal is notched out and an RMS value of the total harmonics, wide-band noise and interference is calculated. Channel Separation (dB) - Also known as Cross-Talk. This is a measure of the amount one channel is isolated from the other. Normally measured by sending a full scale signal down one channel and measuring the other. w PD, Rev 4.1, June 2009 11 WM8986 Production Data POWER CONSUMPTION Typical power consumption for various scenarios is shown below. DCVDD(V) DCVDD(mA) DBVDD(V) DBVDD(mA) AVDD1(V) AVDD1(mA) AVDD2(V) AVDD2(mA) Total (mW) All measurements are made with quiescent signal. 1.8 1.8 1.8 3.3 3.6 0.002 0.002 0.002 0.006 0.008 1.8 3.3 3.3 3.3 3.6 0 0 0 0 0 2.5 3 3.3 3.3 3.6 0.01 0.011 0.012 0.011 0.012 2.5 3 3.3 3.3 3.6 0 0 0 0 0 0.03 0.04 0.04 0.06 0.07 Standby mode (Lowest Power) 1.8 1.8 1.8 3.3 3.6 0.002 0.002 0.002 0.006 0.008 1.8 3.3 3.3 3.3 3.6 0 0 0 0 0 2.5 3 3.3 3.3 3.6 0.117 0.138 0.149 0.149 0.157 2.5 3 3.3 3.3 3.6 0 0 0 0 0 0.30 0.42 0.50 0.51 0.59 DAC Playback 32 load L/ROUT2 - Class AB Mode fs=44.1kHz 1.8 1.8 3.3 3.6 3.336 3.336 7.182 8.098 1.8 0.003 3.3 0.0021 3.3 0.0021 3.6 0.025 2.5 3 3.3 3.6 2.238 2.728 3.025 3.325 2.5 3 3.3 3.6 0.28 0.35 0.39 0.44 12.31 15.24 34.98 42.80 Description Off (Default Settings) Table 1 Power Consumption Contact Wolfson for more information on device power consumption. w PD, Rev 4.1, June 2009 12 Production Data WM8986 AUDIO PATHS OVERVIEW Figure 1 Audio Paths Overview w PD, Rev 4.1, June 2009 13 WM8986 Production Data SIGNAL TIMING REQUIREMENTS SYSTEM CLOCK TIMING tMCLKL MCLK tMCLKH tMCLKY Figure 2 System Clock Timing Requirements Test Conditions DCVDD=1.8V, DBVDD=AVDD1=AVDD2=3.3V, DGND=AGND1=AGND2=0V, TA = +25oC, Slave Mode PARAMETER SYMBOL CONDITIONS MIN TMCLKY MCLK=SYSCLK (=256fs) 81.38 MCLK input to PLL Note 1 20 TYP MAX UNIT System Clock Timing Information MCLK cycle time MCLK duty cycle TMCLKDS ns ns 60:40 40:60 Note: 1. PLL pre-scaling and PLL N and K values should be set appropriately so that SYSCLK is no greater than 12.288MHz. AUDIO INTERFACE TIMING - MASTER MODE Figure 3 Digital Audio Data Timing - Master Mode (see Control Interface) w PD, Rev 4.1, June 2009 14 WM8986 Production Data Test Conditions DCVDD=1.8V, DBVDD=AVDD1=AVDD2=3.3V, DGND=AGND1=AGND2=0V, TA=+25oC, Master Mode, fs=48kHz, MCLK=256fs, 24-bit data, unless otherwise stated. PARAMETER SYMBOL MIN TYP MAX UNIT Audio Data Input Timing Information LRC propagation delay from BCLK falling edge tDL DACDAT setup time to BCLK rising edge tDST 10 ns DACDAT hold time from BCLK rising edge tDHT 10 ns 10 ns AUDIO INTERFACE TIMING - SLAVE MODE Figure 4 Digital Audio Data Timing - Slave Mode Test Conditions DCVDD=1.8V, DBVDD=AVDD1=AVDD2=3.3V, DGND=AGND1=AGND2=0V, TA=+25oC, Slave Mode, fs=48kHz, MCLK= 256fs, 24-bit data, unless otherwise stated. PARAMETER SYMBOL MIN TYP MAX UNIT Audio Data Input Timing Information BCLK cycle time tBCY 50 ns BCLK pulse width high tBCH 20 ns BCLK pulse width low tBCL 20 ns LRC set-up time to BCLK rising edge tLRSU 10 ns LRC hold time from BCLK rising edge tLRH 10 ns DACDAT hold time from BCLK rising edge tDH 10 ns DACDAT set-up time to BCLK rising edge tDs 10 ns Note: BCLK period should always be greater than or equal to MCLK period. w PD, Rev 4.1, June 2009 15 WM8986 Production Data CONTROL INTERFACE TIMING - 3-WIRE MODE 3-wire mode is selected by connecting the MODE pin high. Figure 5 Control Interface Timing - 3-Wire Serial Control Mode Test Conditions o DCVDD = 1.8V, DBVDD = AVDD1 = AVDD2 = 3.3V, DGND = AGND1 = AGND2 = 0V, TA=+25 C, Slave Mode, fs=48kHz, MCLK = 256fs, 24-bit data, unless otherwise stated. PARAMETER SYMBOL MIN TYP MAX UNIT Program Register Input Information SCLK rising edge to CSB rising edge tSCS 80 ns SCLK pulse cycle time tSCY 200 ns SCLK pulse width low tSCL 80 ns SCLK pulse width high tSCH 80 ns SDIN to SCLK set-up time tDSU 40 ns SCLK to SDIN hold time tDHO 40 ns CSB pulse width low tCSL 40 ns CSB pulse width high tCSH 40 ns CSB rising to SCLK rising tCSS 40 ns tps 0 Pulse width of spikes that will be suppressed w 5 ns PD, Rev 4.1, June 2009 16 WM8986 Production Data CONTROL INTERFACE TIMING - 2-WIRE MODE 2-wire mode is selected by connecting the MODE pin low. t3 t3 t5 SDIN t4 t6 t2 t8 SCLK t1 t9 t7 Figure 6 Control Interface Timing - 2-Wire Serial Control Mode Test Conditions DCVDD=1.8V, DBVDD=AVDD1=AVDD2=3.3V, DGND=AGND1=AGND2=0V, MCLK = 256fs, 24-bit data, unless otherwise stated. TA=+25oC, PARAMETER SYMBOL MIN SCLK Low Pulse-Width t1 1.3 us SCLK High Pulse-Width t2 600 ns Hold Time (Start Condition) t3 600 ns Setup Time (Start Condition) t4 600 ns Data Setup Time t5 100 SDIN, SCLK Rise Time t6 300 SDIN, SCLK Fall Time t7 300 Setup Time (Stop Condition) t8 Slave TYP Mode, fs=48kHz, MAX UNIT 526 kHz Program Register Input Information SCLK Frequency 0 Data Hold Time t9 Pulse width of spikes that will be suppressed tps w ns 600 0 ns ns ns 900 ns 5 ns PD, Rev 4.1, June 2009 17 WM8986 Production Data INTERNAL POWER ON RESET CIRCUIT Figure 7 Internal Power on Reset Circuit Schematic The WM8986 includes an internal Power-On-Reset Circuit, as shown in Figure 7, which is used to reset the digital logic into a default state after power up. The POR circuit is powered from AVDD1 and monitors DCVDD. It asserts PORB low if AVDD1 or DCVDD is below a minimum threshold. Figure 8 Typical Power up Sequence where AVDD1 is Powered before DCVDD Figure 8 shows a typical power-up sequence where AVDD1 comes up first. When AVDD1 goes above the minimum threshold, Vpora, there is enough voltage for the circuit to guarantee PORB is asserted low and the chip is held in reset. In this condition, all writes to the control interface are ignored. Now AVDD1 is at full supply level. Next DCVDD rises to Vpord_on and PORB is released high and all registers are in their default state and writes to the control interface may take place. On power down, where AVDD1 falls first, PORB is asserted low whenever AVDD1 drops below the minimum threshold Vpora_off. w PD, Rev 4.1, June 2009 18 WM8986 Production Data Figure 9 Typical Power up Sequence where DCVDD is Powered before AVDD1 Figure 9 shows a typical power-up sequence where DCVDD comes up first. First it is assumed that DCVDD is already up to specified operating voltage. When AVDD1 goes above the minimum threshold, Vpora, there is enough voltage for the circuit to guarantee PORB is asserted low and the chip is held in reset. In this condition, all writes to the control interface are ignored. When AVDD1 rises to Vpora_on, PORB is released high and all registers are in their default state and writes to the control interface may take place. On power down, where DCVDD falls first, PORB is asserted low whenever DCVDD drops below the minimum threshold Vpord_off. SYMBOL MIN TYP MAX UNIT Vpora 0.4 0.6 0.8 V Vpora_on 0.9 1.2 1.6 V Vpora_off 0.4 0.6 0.8 V Vpord_on 0.5 0.7 0.9 V Vpord_off 0.4 0.6 0.8 V Table 2 Typical POR Operation (Typical Simulated Values) Notes: w 1. If AVDD1 and DCVDD suffer a brown-out (i.e. drop below the minimum recommended operating level but do not go below Vpora_off or Vpord_off) then the chip will not reset and will resume normal operation when the voltage is back to the recommended level again. 2. The chip will enter reset at power down when AVDD1 or DCVDD falls below Vpora_off or Vpord_off. This may be important if the supply is turned on and off frequently by a power management system. 3. The minimum tpor period is maintained even if DCVDD and AVDD1 have zero rise time. This specification is guaranteed by design rather than test. PD, Rev 4.1, June 2009 19 WM8986 Production Data RECOMMENDED POWER UP/DOWN SEQUENCE In order to minimise output pop and click noise, it is recommended that the WM8986 device is powered up and down under control using the following sequences: Power Up: 1. Turn on external power supplies. Wait for supply voltage to settle. 2. Set low analogue bias mode, BIASCUT = 1 3. Enable thermal shutdown TSDEN = TSOPCTRL = 1 4. Enable Internal bias BIASEN = 1. 5. Mute all outputs and set PGAs to minimum gain, R52 to R57 = 0x140h. 6. Enable VMID independent current bias, POBCTRL = 1. 7. Enable required outputs, DACs and mixers. 8. Enable VMID with required charge time e.g. VMIDSEL=01. 9. Wait 500ms 1 10. Setup digital interface, input amplifiers, PLL, and DACs for desired operation. 11. Disable VMID independent current bias, POBCTRL = 0. 12. Unmute L/ROUT1 and set desired volume, e.g. for 0dB R52 and R53 = 0x139h. 13. Unmute L/ROUT2 and set desired volume, e.g. for 0dB R54 and R55 = 0x139h. Power Down 2: 1. Disable Thermal shutdown, TSDEN = TSOPCTRL = 0 2. Disable VMIDSEL=00 and BIASEN=0 3. Wait for VMID to discharge 3 4. Power off registers R1, R2, R3 = 0x000h 5. Remove external power supplies Notes: w 1. Charging time constant is determined by impedance selected by VMIDSEL and the value of decoupling capacitor connected to VMID pin. 2. It is possible to interrupt the power down sequence and power up to VMID before the allocated VMID discharge time. This is done by following the power-up sequence omitting steps 4 to 8. 3. Discharge time constant is determined by the values of analogue output capacitors. PD, Rev 4.1, June 2009 20 WM8986 Production Data Figure 10 DAC Power Up and Down Sequence (not to scale) SYMBOL MIN TYPICAL MAX UNIT tline_midrail_on 300 tline_midrail_off >6 ms s thp_midrail_on 300 ms thp__midrail_off >6 s tdacint 2/fs n/fs DAC Group Delay 51/fs n/fs Table 3 Typical POR Operation (Typical Simulated Values) Notes: w 1. The lineout charge time, tline_midrail_on, is determined by the VMID pin charge time. This time is dependent upon the value of VMID decoupling capacitor and VMID pin input resistance and AVDD1 power supply rise time. The values above were measured using a 4.7F capacitor. 2. It is not advisable to allow DACDAT data input during initialisation of the DAC. If the DAC data value is not zero at point of initialisation, then this is likely to cause a pop noise on the analogue outputs. The same is also true if the DACDAT is removed at a non-zero value, and no mute function has been applied to the signal beforehand. 3. The lineout discharge time, tline_midrail_off, is determined by the VMID pin discharge time. This time is dependent upon the value of VMID decoupling capacitor and VMID pin input resistance. The values above were measured using a 4.7F capacitor. 4. The headphone charge time, thp_midrail_on, is dependent upon the value of VMID decoupling capacitor and VMID pin input resistance and AVDD1 power supply rise time. The values above were measured using a 4.7F VMID decoupling capacitor. 5. The headphone discharge time, thp_midrail_off, is dependent upon the value of VMID decoupling capacitor and VMID pin input resistance. The values above were measured using a 4.7F VMID decoupling capacitor. 6. The VMIDSEL and BIASEN bits must be set to enable analogue output midrail voltage and for normal DAC operation. PD, Rev 4.1, June 2009 21 WM8986 Production Data DEVICE DESCRIPTION INTRODUCTION The WM8986 is a low power audio IC combining a high quality stereo audio DAC with flexible line and microphone input and output processing. FEATURES The chip offers great flexibility in use, and so can support many different modes of operation as follows: HI-FI DAC The hi-fi DAC provides high quality audio playback suitable for all portable audio hi-fi type applications, including MP3 players and portable disc players of all types. OUTPUT MIXERS Flexible mixing is provided on the outputs of the device. A stereo mixer is provided for the stereo headphone or line outputs, LOUT1/ROUT1, and additional summers on the OUT3/OUT4 outputs allow for an optional differential or stereo line output on these pins. Gain adjustment PGAs are provided for the LOUT1/ROUT1 and LOUT2/ROUT2 outputs, and signal switching is provided to allow for all possible signal combinations. OUT3 and OUT4 can be configured to provide an additional stereo or mono differential lineout from the output of the DACs, the mixers or the input microphone boost stages. They can also provide a midrail reference for pseudo differential inputs to external amplifiers. OUT3 and OUT4 should not be used as a buffered midrail reference in capless mode. LINE INPUTS (AUXL, AUXR) The inputs, AUXL and AUXR, can be used as a stereo line input (e.g. melody chip or FM radio) or as an input for warning tones (or `beeps') etc. These inputs can be summed into the output paths, along with the microphone preamp outputs. MICROPHONE INPUTS Two pairs of stereo microphone inputs are provided, allowing a pair of stereo microphones to be pseudo-differentially connected, with user defined gain. The provision of the common mode input pin for each stereo input allows for rejection of common mode noise on the microphone inputs (level depends on gain setting chosen). Total gain through the microphone paths of up to +55.25dB can be selected. AUDIO INTERFACES The WM8986 has a standard audio interface, to support the transmission of stereo data to and from the chip. This interface is a 3 wire standard audio interface which supports a number of audio data formats including: * I2S * DSP/PCM Mode (a burst mode in which LRC sync plus 2 data packed words are transmitted) * MSB-First, left justified * MSB-First, right justified The interface can operate in master or slave modes. CONTROL INTERFACES To allow full software control over all features, the WM8986 offers a choice of 2 or 3 wire control interface. It is fully compatible and an ideal partner for a wide range of industry standard microprocessors, controllers and DSPs. w PD, Rev 4.1, June 2009 22 WM8986 Production Data Selection of the mode is via the MODE pin. In 2 wire mode, the address of the device is fixed as 0011010. CLOCKING SCHEMES WM8986 offers the normal audio DAC clocking scheme operation, where 256fs MCLK is provided to the DAC. A flexible clock divider allows the 256fs DAC clock to be generated from a range of input clock frequencies, for example, 256fs, 384fs, 512fs and 768fs. A PLL is included which may be used to generate these clocks in the event that they are not available from the system controller. This PLL can accept a range of common input clock frequencies between 8MHz and 50MHz to generate high quality audio clocks. If this PLL is not required for generation of these clocks, it can be reconfigured to generate alternative clocks which may then be output on the GPIO1 pin and used elsewhere in the system; available in 2-wire control mode only. POWER CONTROL The design of the WM8986 has given much attention to power consumption without compromising performance. The WM8986 operates at low analog and digital supply voltages, and includes the ability to power off any unused parts of the circuitry under software control. It also includes standby and power off modes. INPUT SIGNAL PATH The WM8986 has a number of flexible analogue inputs. There are two input channels, Left and Right, each of which consists of an input PGA stage followed by a boost/mix stage which drives into the output mixers. Each input path has three input pins which can be configured in a variety of ways to accommodate single-ended, pseudo-differential or dual differential microphones. There are two auxiliary input pins which can be fed into to the input boost/mix stage as well as driving into the output path. An additional signal path exists from the output of the boost/mix stage into the output left/right mixers. MICROPHONE INPUTS The WM8986 can accommodate a variety of microphone configurations including single ended and pseudo-differential inputs. The inputs to the left differential input PGA are LIN and LIP. The inputs to the right differential input PGA are RIN and RIP. w PD, Rev 4.1, June 2009 23 WM8986 Production Data Figure 11 Microphone Input PGA Circuit In single-ended microphone input configuration the microphone signal should be input to LIN or RIN and the non-inverting input of the input PGA clamped to VMID. GND 65k MIC 680R + 65k VMID INPUT PGA To input mixers MICBIAS Figure 12 Psuedo-Differential Microphone Configuration w PD, Rev 4.1, June 2009 24 WM8986 Production Data 680R MICBIAS 65k MIC To input mixers + GND VMID INPUT PGA Figure 13 Single-ended Microphone Configuration The input PGAs are enabled by the INPPGAENL and INPPGAENR register bits. REGISTER ADDRESS BIT R2 (02h) Power Management 2 LABEL DEFAULT DESCRIPTION 2 INPPGAENL 0 Left channel input PGA enable 0 = disabled 1 = enabled 3 INPPGAENR 0 Right channel input PGA enable 0 = disabled 1 = enabled Table 4 Input PGA Enable Register Settings REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R44 (2Ch) Input Control 1 LIN2INPPGA 1 Connect LIN pin to left channel input PGA negative terminal. 0 = LIN not connected to input PGA 1 = LIN connected to input PGA amplifier negative terminal. 5 RIN2INPPGA 1 Connect RIN pin to right channel input PGA negative terminal. 0 = RIN not connected to input PGA 1 = RIN connected to right channel input PGA amplifier negative terminal. Table 5 Input PGA Control w PD, Rev 4.1, June 2009 25 WM8986 Production Data INPUT PGA VOLUME CONTROLS The input microphone PGAs have a gain range from -12dB to +35.25dB in 0.75dB steps. The gain from the LIN/RIN input to the PGA output is controlled by the register bits INPPGAVOLL[5:0] and INPPGABVOLR[5:0]. These register bits also affect the LIP pin when LIP2INPPGA=1 and the RIP pin when RIP2INPPGA=1. BIT LABEL DEFAULT DESCRIPTION REGISTER ADDRESS R45 (20h) Left channel input PGA volume control R46 (2Eh) Right channel input PGA volume control 5:0 INPPGAVOLL 010000 (0dB) Left channel input PGA volume 000000 = -12dB 000001 = -11.25db . 010000 = 0dB . 111111 = +35.25dB 6 INPPGAMUTEL 0 Mute control for left channel input PGA: 0 = Input PGA not muted, normal operation 1 = Input PGA muted (and disconnected from the following input BOOST stage). 7 INPPGAZCL 0 Left channel input PGA zero cross enable: 0 = Update gain when gain register changes 1 = Update gain on 1st zero cross after gain register write. 8 INPPGAVU Not latched INPPGA left and INPPGA right volume do not update until a 1 is written to INPPGAVU (in reg 45 or 46) (See "Volume Updates" below) 5:0 INPPGAVOLR 010000 (0dB) Right channel input PGA volume 000000 = -12dB 000001 = -11.25db . 010000 = 0dB . 111111 = +35.25dB 6 INPPGAMUTER 0 Mute control for right channel input PGA: 0 = Input PGA not muted, normal operation 1 = Input PGA muted (and disconnected from the following input BOOST stage). 7 INPPGAZCR 0 Right channel input PGA zero cross enable: 0 = Update gain when gain register changes 1 = Update gain on 1st zero cross after gain register write. 8 INPPGAVU Not latched INPPGA left and INPPGA right volume do not update until a 1 is written to INPPGAVU (in reg 45 or 46) (See "Volume Updates" below) Table 6 Input PGA Volume Control w PD, Rev 4.1, June 2009 26 WM8986 Production Data VOLUME UPDATES Volume settings will not be applied to the PGAs until a '1' is written to one of the INPPGAVU bits. This is to allow left and right channels to be updated at the same time, as shown in Figure 14. Figure 14 Simultaneous Left and Right Volume Updates If the volume is adjusted while the signal is a non-zero value, an audible click can occur as shown in Figure 15. Figure 15 Click Noise During Volume Update In order to prevent this click noise, a zero cross function is provided. When enabled, this will cause the PGA volume to update only when a zero crossing occurs, minimising click noise as shown in Figure 16. w PD, Rev 4.1, June 2009 27 WM8986 Production Data Figure 16 Volume Update Using Zero Cross Detection If there is a long period where no zero-crossing occurs, a timeout circuit in the WM8986 will automatically update the volume. The volume updates will occur between one and two timeout periods, depending on when the INPPGAVU bit is set as shown in Figure 17. Figure 17 Volume Update After Timeout w PD, Rev 4.1, June 2009 28 WM8986 Production Data AUXILIARY INPUTS There are two auxiliary inputs, AUXL and AUXR which can be used for a variety of purposes such as stereo line inputs or as a `beep' input signal to be mixed with the outputs. The AUXL/R inputs can be used as a line input to the input BOOST stage which has adjustable gain of -12dB to +6dB in 3dB steps, with an additional "off" state (i.e. not connected). See the INPUT BOOST section for further details. The AUXL/R inputs can also be mixed into the output channel mixers, with a gain of -15dB to +6dB plus off. INPUT BOOST Each of the stereo input PGA stages is followed by an input BOOST circuit. The input BOOST circuit has 2 selectable inputs: the input microphone PGA output or the AUX amplifier output. These three inputs can be mixed together and have individual gain boost/adjust as shown in Figure 18. Figure 18 Input Boost Stage w PD, Rev 4.1, June 2009 29 WM8986 Production Data The input PGA paths can have a +20dB boost (PGABOOSTL/R=1), a 0dB pass through (PGABOOSTL/R=0) or be completely isolated from the input boost circuit (INPPGAMUTEL/R=1). REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R47 (2Fh) Left Input BOOST control 8 PGABOOSTL 1 Boost enable for left channel input PGA: 0 = PGA output has +0dB gain through input BOOST stage. 1 = PGA output has +20dB gain through input BOOST stage. R48 (30h) Right Input BOOST control 8 PGABOOSTR 1 Boost enable for right channel input PGA: 0 = PGA output has +0dB gain through input BOOST stage. 1 = PGA output has +20dB gain through input BOOST stage. Table 7 Input BOOST Stage Control The Auxiliary amplifier path to the BOOST stages is controlled by the AUXL2BOOSTVOL[2:0] and AUXR2BOOSTVOL[2:0] register bits. When AUXL2BOOSTVOL/AUXR2BOOSTVOL=000 this path is completely disconnected from the BOOST stage. Settings 001 through to 111 control the gain in 3dB steps from -12dB to +6dB. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R47 (2Fh) Left channel Input BOOST control 2:0 AUXL2BOOSTVOL 000 Controls the auxiliary amplifier to the left channel input boost stage: 000 = Path disabled (disconnected) 001 = -12dB gain 010 = -9dB gain 011 = -6dB gain 100 = -3dB gain 101 = +0dB gain 110 = +3dB gain 111 = +6dB gain R48 (30h) Right channel Input BOOST control 2:0 AUXR2BOOSTVOL 000 Controls the auxiliary amplifier to the right channel input boost stage: 000 = Path disabled (disconnected) 001 = -12dB gain 010 = -9dB gain 011 = -6dB gain 100 = -3dB gain 101 = +0dB gain 110 = +3dB gain 111 = +6dB gain Table 8 Input BOOST Stage Control w PD, Rev 4.1, June 2009 30 WM8986 Production Data The BOOST stage is enabled under control of the BOOSTEN register bit. REGISTER ADDRESS R2 (02h) Power management 2 BIT LABEL DEFAULT DESCRIPTION 4 BOOSTENL 0 Left channel Input BOOST enable 0 = Boost stage OFF 1 = Boost stage ON 5 BOOSTENR 0 Right channel Input BOOST enable 0 = Boost stage OFF 1 = Boost stage ON Table 9 Input BOOST Enable Control OUTPUT SIGNAL PATH The WM8986 output signal paths consist of digital application filters, up-sampling filters, stereo Hi-Fi DACs, analogue mixers, stereo headphone and stereo line/mono/midrail output drivers. The digital filters and DAC are enabled by register bits DACENL and DACENR. The mixers and output drivers can be separately enabled by individual control bits (see Analogue Outputs). Thus it is possible to utilise the analogue mixing and amplification provided by the WM8986, irrespective of whether the DACs are running or not. The WM8986 DACs receive digital input data on the DACDAT pin. The digital filter block processes the data to provide the following functions: Digital volume control Graphic equaliser and 3-D enhancement A digital peak limiter. Sigma-Delta Modulation High performance sigma-delta audio DAC converts the digital data into an analogue signal. Figure 19 DAC Digital Filter Path The analogue outputs from the DACs can then be mixed with the various analogue inputs. The mix is fed to the output drivers for headphone (LOUT1/ROUT1, LOUT2/ROUT2) or line (OUT3/OUT4). OUT3 and OUT4 have additional mixers which allow them to output different signals to the line outputs. DIGITAL PLAYBACK (DAC) PATH Digital data is passed to the WM8986 via the flexible audio interface and is then passed through a variety of advanced digital filters as shown in Figure 19 to the hi-fi DACs. The DACs are enabled by the DACENL/R register bits. REGISTER ADDRESS R3 (03h) Power Management 3 BIT LABEL DEFAULT DESCRIPTION 0 DACENL 0 Left channel DAC enable 0 = DAC disabled 1 = DAC enabled 1 DACENR 0 Right channel DAC enable 0 = DAC disabled 1 = DAC enabled Table 10 DAC Enable Control The WM8986 also has a Soft Mute function, which when enabled, gradually attenuates the volume of the digital signal to zero. When disabled, the gain will ramp back up to the digital gain setting. This function is enabled by default. To play back an audio signal, it must first be disabled by setting the SOFTMUTE bit to zero. w PD, Rev 4.1, June 2009 31 WM8986 Production Data REGISTER ADDRESS BIT R10 (0Ah) DAC Control LABEL DEFAULT DESCRIPTION 0 DACPOL 0 Left DAC output polarity: 0 = non-inverted 1 = inverted (180 degrees phase shift) 1 DACRPOL 0 Right DAC output polarity: 0 = non-inverted 1 = inverted (180 degrees phase shift) 2 AMUTE 0 Automute enable 0 = Amute disabled 1 = Amute enabled 3 DACOSR128 0 DAC oversampling rate: 0 = 64x (lowest power) 1 = 128x (best performance) 6 SOFTMUTE 0 Softmute enable: 0 = Enabled 1 = Disabled Table 11 DAC Control Register The digital audio data is converted to oversampled bit streams in the on-chip, true 24-bit digital interpolation filters. The bitstream data enters the multi-bit, sigma-delta DACs, which convert it to a high quality analogue audio signal. The multi-bit DAC architecture reduces high frequency noise and sensitivity to clock jitter. It also uses a Dynamic Element Matching technique for high linearity and low distortion. The DAC output phase defaults to non-inverted. Setting DACLPOL will invert the DAC output phase on the left channel and DACRPOL inverts the phase on the right channel. AUTO-MUTE The DAC has an auto-mute function which applies an analogue mute when 1024 consecutive zeros are detected. The mute is released as soon as a non-zero sample is detected. Auto-mute can be disabled using the AMUTE control bit. DIGITAL HI-FI DAC VOLUME (GAIN) CONTROL The signal volume from each Hi-Fi DAC can be controlled digitally. The gain range is -127dB to 0dB in 0.5dB steps. The level of attenuation for an eight-bit code X is given by: 0.5 x (X-255) dB for 1 X 255; REGISTER ADDRESS R11 (0Bh) Left DAC Digital Volume R12 (0Ch) Right DAC Digital Volume BIT LABEL MUTE for X = 0 DEFAULT DESCRIPTION 7:0 DACLVOL [7:0] 11111111 ( 0dB ) Left DAC Digital Volume Control 0000 0000 = Digital Mute 0000 0001 = -127dB 0000 0010 = -126.5dB ... 0.5dB steps up to 1111 1111 = 0dB 8 DACVU Not latched DAC left and DAC right volume do not update until a 1 is written to DACVU (in reg 11 or 12) 7:0 DACRVOL [7:0] 11111111 ( 0dB ) Right DAC Digital Volume Control 0000 0000 = Digital Mute 0000 0001 = -127dB 0000 0010 = -126.5dB ... 0.5dB steps up to 1111 1111 = 0dB 8 DACVU Not latched DAC left and DAC right volume do not update until a 1 is written to DACVU (in reg 11 or 12) Table 12 DAC Digital Volume Control w PD, Rev 4.1, June 2009 32 WM8986 Production Data Note: An additional gain of up to 12dB can be added using the gain block embedded in the digital peak limiter circuit (see DAC OUTPUT LIMITER section). 5-BAND EQUALISER A 5-band graphic equaliser function which can be used to change the output frequency levels to suit the environment. This is described in the 5-BAND EQUALISER section. 3-D ENHANCEMENT The WM8986 has an advanced digital 3-D enhancement feature which can be used to vary the perceived stereo separation of the left and right channels. Refer to the 3-D STEREO ENHANCEMENT section for further details on this feature. DAC DIGITAL OUTPUT LIMITER The WM8986 has a digital output limiter function. The operation of this is shown in Figure 20. In this diagram the upper graph shows the envelope of the input/output signals and the lower graph shows the gain characteristic. Figure 20 DAC Digital Limiter Operation The limiter has a programmable upper threshold which is close to 0dB. Referring to Figure 20, in normal operation (LIMBOOST=000 => limit only) signals below this threshold are unaffected by the limiter. Signals above the upper threshold are attenuated at a specific attack rate (set by the LIMATK register bits) until the signal falls below the threshold. The limiter also has a lower threshold 1dB below the upper threshold. When the signal falls below the lower threshold the signal is amplified at a specific decay rate (controlled by LIMDCY register bits) until a gain of 0dB is reached. Both threshold levels are controlled by the LIMLVL register bits. The upper threshold is 0.5dB above the value programmed by LIMLVL and the lower threshold is 0.5dB below the LIMLVL value. VOLUME BOOST The limiter has programmable upper gain which boosts signals below the threshold to compress the dynamic range of the signal and increase its perceived loudness. This operates as an ALC function with limited boost capability. The volume boost is from 0dB to +12dB in 1dB steps, controlled by the LIMBOOST register bits. The output limiter volume boost can also be used as a stand alone digital gain boost when the limiter is disabled. w PD, Rev 4.1, June 2009 33 WM8986 Production Data REGISTER ADDRESS R24 (18h) DAC digital limiter control 1 BIT 3:0 LABEL LIMATK DEFAULT 0010 DESCRIPTION Limiter Attack time (per 6dB gain change) for 44.1kHz sampling. Note that these are proportionally related to sample rate. 0000 = 94us 0001 = 188s 0010 = 375us 0011 = 750us 0100 = 1.5ms 0101 = 3ms 0110 = 6ms 0111 = 12ms 1000 = 24ms 1001 = 48ms 1010 = 96ms 1011 to 1111 = 192ms 7:4 LIMDCY 0011 Limiter Decay time (per 6dB gain change) for 44.1kHz sampling. Note that these are proportionally related to sample rate: 0000 = 750us 0001 = 1.5ms 0010 = 3ms 0011 = 6ms 0100 = 12ms 0101 = 24ms 0110 = 48ms 0111 = 96ms 1000 = 192ms 1001 = 384ms 1010 = 768ms 1011 to 1111 = 1.536s R25 (19h) DAC digital limiter control 2 8 LIMEN 0 Enable the DAC digital limiter: 0=disabled 1=enabled 3:0 LIMBOOST 0000 Limiter volume boost (can be used as a stand alone volume boost when LIMEN=0): 0000 = 0dB 0001 = +1dB 0010 = +2dB 0011 = +3dB 0100 = +4dB 0101 = +5dB 0110 = +6dB 0111 = +7dB 1000 = +8dB 1001 = +9dB 1010 = +10dB 1011 = +11dB 1100 = +12dB 1101 to 1111 = reserved w PD, Rev 4.1, June 2009 34 WM8986 Production Data REGISTER ADDRESS BIT 6:4 LABEL LIMLVL DEFAULT 000 DESCRIPTION Programmable signal threshold level (determines level at which the limiter starts to operate) 000 = -1dB 001 = -2dB 010 = -3dB 011 = -4dB 100 = -5dB 101 to 111 = -6dB Table 13 DAC Digital Limiter Control 5-BAND GRAPHIC EQUALISER A 5-band graphic equaliser is provided, which can be applied to the DAC path, together with 3D enhancement, under control of the EQ3DEN register bit. REGISTER ADDRESS R18 (12h) EQ Control 1 BIT 8 LABEL EQ3DEN DEFAULT 1 DESCRIPTION 0 = Equaliser and 3D Enhancement disabled 1 = Equaliser and 3D Enhancement enabled Table 14 EQ and 3D Enhancement enable Note: The DACs must be disabled before changing the EQ3DEN bit. A 5-band graphic equaliser consists of low and high frequency shelving filters (Band 1 and 5) and three peak filters for the centre bands. Each has adjustable cut-off or centre frequency, and selectable boost (+/- 12dB in 1dB steps). The peak filters have selectable bandwidth. To enable the use of the 5-band equaliser the device must be in 128fs mode by setting M128ENB to 1 in register R7 bit 8. Refer to the Low Power section under Power Management below for more details. REGISTER ADDRESS R18 (12h) EQ Band 1 Control BIT LABEL DEFAULT DESCRIPTION 4:0 EQ1G 01100 (0dB) Band 1 Gain Control. See Table 20 for details. 6:5 EQ1C 01 Band 1 Cut-off Frequency: 00 = 80Hz 01 = 105Hz 10 = 135Hz 11 = 175Hz Table 15 EQ Band 1 Control REGISTER ADDRESS R19 (13h) EQ Band 2 Control BIT LABEL DEFAULT 4:0 EQ2G 01100 (0dB) 6:5 EQ2C 01 DESCRIPTION Band 2 Gain Control. See Table 20 for details. Band 2 Centre Frequency: 00 = 230Hz 01 = 300Hz 10 = 385Hz 8 EQ2BW 0 11 = 500Hz Band 2 Bandwidth Control 0 = narrow bandwidth 1 = wide bandwidth Table 16 EQ Band 2 Control w PD, Rev 4.1, June 2009 35 WM8986 Production Data REGISTER ADDRESS R20 (14h) EQ Band 3 Control BIT LABEL DEFAULT 4:0 EQ3G 01100 (0dB) 6:5 EQ3C 01 DESCRIPTION Band 3 Gain Control. See Table 20 for details. Band 3 Centre Frequency: 00 = 650Hz 01 = 850Hz 8 EQ3BW 10 = 1.1kHz 11 = 1.4kHz Band 3 Bandwidth Control 0 = narrow bandwidth 1 = wide bandwidth 0 Table 17 EQ Band 3 Control REGISTER ADDRESS R21 (15h) EQ Band 4 Control BIT LABEL DEFAULT 4:0 EQ4G 01100 (0dB) 6:5 EQ4C 01 DESCRIPTION Band 4 Gain Control. See Table 20 for details Band 4 Centre Frequency: 00 = 1.8kHz 01 = 2.4kHz 8 EQ4BW 10 = 3.2kHz 11 = 4.1kHz Band 4 Bandwidth Control 0 = narrow bandwidth 1 = wide bandwidth 0 Table 18 EQ Band 4 Control REGISTER ADDRESS R22 (16h) EQ Band 5 Gain Control BIT LABEL DEFAULT DESCRIPTION 4:0 EQ5G 01100 (0dB) Band 5 Gain Control. See Table 20 for details. 6:5 EQ5C 01 Band 5 Cut-off Frequency: 00 = 5.3kHz 01 = 6.9kHz 10 = 9kHz 11 = 11.7kHz Table 19 EQ Band 5 Control GAIN REGISTER GAIN 00000 +12dB 00001 +11dB 00010 +10dB .... (1dB steps) 01100 0dB 01101 -1dB 11000 -12dB 11001 to 11111 Reserved Table 20 Gain Register Table See also Figure 40 to Figure 53 for equaliser and high pass filter responses. w PD, Rev 4.1, June 2009 36 WM8986 Production Data 3D STEREO ENHANCEMENT The WM8986 has a digital 3D enhancement option to increase the perceived separation between the left and right channels. The DEPTH3D setting controls the degree of stereo expansion. REGISTER ADDRESS R41 (29h) 3D Control BIT 3:0 LABEL DEPTH3D DEFAULT 0000 DESCRIPTION Stereo depth 0000 = Disabled 0001 = 6.67% 0010 = 13.3% 0011 = 20% 0100 = 26.7% 0101 = 33.3% 0110 = 40% 0111 = 46.6% 1000 = 53.3% 1001 = 60% 1010 = 66.7% 1011 = 73.3% 1100 = 80% 1101 = 86.7% 1110 = 93.3% 1111 = 100% (maximum 3D effect) Table 21 3D Stereo Enhancement Function Note: When 3D enhancement is used, it may be necessary to attenuate the signal by 6dB to avoid limiting. ANALOGUE OUTPUTS The WM8986 has three sets of stereo analogue outputs. These are: * LOUT1 and ROUT1 which are normally used to drive a headphone load. * LOUT2 and ROUT2 - which can be used as class D or class AB headphone drivers. * OUT3 and OUT4 - can be configured as a stereo line out (OUT3 is left output and OUT4 is right output) or a differential output. OUT4 can also be used to provide a mono mix of left and right channels. The outputs LOUT2 and ROUT2 are powered from AVDD2 and are capable of driving a 1V rms signal (AVDD1/3.3). LOUT1, ROUT1, OUT3 and OUT4 are powered from AVDD1 LOUT1, ROUT1, LOUT2 and ROUT2 have individual analogue volume PGAs with -57dB to +6dB gain ranges. There are four output mixers in the output signal path, the left and right channel mixers which control the signals to headphone (and optionally the line outputs) and also dedicated OUT3 and OUT4 mixers. LEFT AND RIGHT OUTPUT CHANNEL MIXERS The left and right output channel mixers are shown in Figure 21. These mixers allow the analogue inputs and the DAC left and right channels to be combined as desired. This allows a mono mix of the DAC channels to be performed as well as mixing in external line-in from the AUX or speech from the input PGAs. The AUX and PGA path inputs have individual volume control from -15dB to +6dB and the DAC volume can be adjusted in the digital domain if required. The output of these mixers is connected to both the headphone (LOUT1 and ROUT1) and class D headphone (LOUT2 and ROUT2) and can optionally be connected to the OUT3 and OUT4 mixers. w PD, Rev 4.1, June 2009 37 WM8986 Production Data Figure 21 Left/Right Output Channel Mixers w PD, Rev 4.1, June 2009 38 WM8986 Production Data REGISTER ADDRESS LABEL DEFAULT DESCRIPTION R43 (2Bh) Output mixer control 8 BYPL2RMIX 0 Left channel input PGA stage to right output mixer 0 = not selected 1 = selected R43 (2Bh) Output mixer control 7 BYPR2LMIX 0 Right channel input PGA stage to Left output mixer 0 = not selected 1 = selected R49 (31h) Output mixer control 5 DACR2LMIX 0 Right DAC output to left output mixer 0 = not selected 1 = selected 6 DACL2RMIX 0 Left DAC output to right output mixer 0 = not selected 1 = selected 0 DACL2LMIX 1 Left DAC output to left output mixer 0 = not selected 1 = selected 1 BYPL2LMIX 0 Left channel input PGA stage to left output mixer 0 = not selected 1 = selected 4:2 BYPLMIXVOL 5 AUXL2LMIX 8:6 AUXLMIXVOL R50 (32h) Left channel output mixer control w BIT 000 Volume control for Left channel input PGA to left output channel mixer 000 = -15dB 001 = -12dB 010 = -9dB 011 = -6dB 100 = -3dB 101 = 0dB 110 = +3dB 111 = +6dB 0 Left Auxiliary input to left channel output mixer: 0 = not selected 1 = selected 000 Aux left channel input to left mixer volume control: 000 = -15dB 001 = -12dB 010 = -9dB 011 = -6dB 100 = -3dB 101 = 0dB 110 = +3dB 111 = +6dB PD, Rev 4.1, June 2009 39 WM8986 Production Data REGISTER ADDRESS R51 (33h) Right channel output mixer control R3 (03h) Power management 3 BIT LABEL DEFAULT DESCRIPTION 0 DACR2RMIX 1 Right DAC output to right output mixer 0 = not selected 1 = selected 1 BYPR2RMIX 0 Right channel input PGA stage to right output mixer 0 = not selected 1 = selected 4:2 BYPRMIXVOL 000 Volume control for Right channel input PGA stage to right output mixer 000 = -15dB 001 = -12dB 010 = -9dB 011 = -6dB 100 = -3dB 101 = 0dB 110 = +3dB 111 = +6dB 5 AUXR2RMIX 8:6 AUXRMIXVOL 2 LMIXEN 0 Left output channel mixer enable: 0 = disabled 1= enabled 3 RMIXEN 0 Right output channel mixer enable: 0 = disabled 1 = enabled 0 Right Auxiliary input to right channel output mixer: 0 = not selected 1 = selected 000 Aux right channel input to right mixer volume control: 000 = -15dB 001 = -12dB 010 = -9dB 011 = -6dB 100 = -3dB 101 = 0dB 110 = +3dB 111 = +6dB Table 22 Left and Right Output Mixer Control HEADPHONE OUTPUTS (LOUT1 AND ROUT1) The headphone outputs LOUT1 and ROUT1 can drive a 16 or 32 headphone load, either through DC blocking capacitors, or DC-coupled to a buffered midrail reference (LOUT2 or ROUT2), saving a capacitor (capless mode). When using capless mode AVDD1 and AVDD2 should use the same supply to maximise supply rejection. OUT3 and OUT4 should not be used as a buffered midrail reference in capless mode. w PD, Rev 4.1, June 2009 40 WM8986 Production Data Headphone Output using DC Blocking Capacitors DC Coupled Headphone Output Figure 22 Recommended Headphone Output Configurations When DC blocking capacitors are used, their capacitance and the load resistance together determine the lower cut-off frequency of the output signal, fc. Increasing the capacitance lowers fc, improving the bass response. Smaller capacitance values will diminish the bass response. Assuming a 16 load and C1, C2 = 220F: fc = 1 / 2 RLC1 = 1 / (2 x 16 x 220F) = 45 Hz In the DC coupled configuration, the headphone pseudo-ground is connected to the buffered midrail reference pin (LOUT2 or ROUT2). The L/ROUT2 pins can be configured as a DC output driver by setting the LOUT2MUTE and ROUT2MUTE register bits. The DC voltage on VMID in this configuration is equal to the DC offset on the LOUT1 and ROUT1 pins therefore no DC blocking capacitors are required. This saves space and material cost in portable applications. It is not recommended to use DC-coupling to line inputs of another device. Although the built-in short circuit protection on the headphone outputs would be tolerant of shorts to ground, such a connection could be noisy, and may not function properly if the other device is grounded. DC-coupled configurations should only be used with headphones. w PD, Rev 4.1, June 2009 41 WM8986 Production Data REGISTER ADDRESS R52 (34h) LOUT1 Volume control R53 ROUT1 Volume control BIT LABEL DEFAULT 111001 (0dB) DESCRIPTION 5:0 LOUT1VOL 6 LOUT1MUTE 0 Left headphone output mute: 0 = Normal operation 1 = Mute 7 LOUT1ZC 0 Headphone volume zero cross enable: 1 = Change gain on zero cross only 0 = Change gain immediately 8 HPVU Not latched LOUT1 and ROUT1 volumes do not update until a 1 is written to HPVU (in reg 52 or 53) 5:0 ROUT1VOL 6 ROUT1MUTE 0 Right headphone output mute: 0 = Normal operation 1 = Mute 7 ROUT1ZC 0 Headphone volume zero cross enable: 1 = Change gain on zero cross only 0 = Change gain immediately 8 HPVU Not latched LOUT1 and ROUT1 volumes do not update until a 1 is written to HPVU (in reg 52 or 53) 111001 (0dB) Left headphone output volume: (1dB steps) 000000 = -57dB ... 111001 = 0dB ... 111111 = +6dB Right headphone output volume: (1dB steps) 000000 = -57dB ... 111001 = 0dB ... 111111 = +6dB Table 23 OUT1 Volume Control w PD, Rev 4.1, June 2009 42 WM8986 Production Data CLASS D / CLASS AB HEADPHONE OUTPUTS (LOUT2 AND ROUT2) The outputs LOUT2 and ROUT2 are designed to drive two headphone loads of 16 or 32 or line outputs (See Headphone Output and Line Output sections, respectively). Each output has an individual volume control PGA, a mute and an enable control bit as shown in Figure 23. LOUT2 and ROUT2 output the left and right channel mixer outputs respectively. REGISTER ADDRESS BIT LABEL R7 (07h) 7:4 DCLKDIV R23 (17h) 8 CLASSDEN DEFAULT DESCRIPTION 1000 Controls clock division from SYSCLK to generate suitable class D clock. Recommended class D clock frequency = 1.4MHz. 0000 = divide by 1 0010 = divide by 2 0011 = divide by 3 0100 = divide by 4 0101 = divide by 5.5 0110 = divide by 6 1000 = divide by 8 1001 = divide by 12 1010 = divide by 16 0 Enable signal for class D mode on LOUT2 and ROUT2 0 = Class AB mode 1 = Class D mode Table 24 Class D Control Registers When driving headphones using class D outputs it is necessary to use appropriate filtering, placed close to the device, to minimise EMI emissions from the headphone cable (Refer to "Applications Information" for more information). This filtering does not prevent class AB mode operation. Figure 23 LOUT2 and ROUT2 Class D Headphone Configuration w PD, Rev 4.1, June 2009 43 WM8986 Production Data Figure 24 LOUT2 and ROUT2 Class AB Headphone Configuration The output configurations shown in Figure 23 and Figure 24 are both suitable for class AB operation. The signal output on LOUT2/ROUT2 comes from the Left/Right Mixer circuits and can be any combination of the DAC output, the output of the input PGA stage, and the AUXL/R inputs. The LOUT2/ROUT2 volume is controlled by the LOUT2VOL/ ROUT2VOL register bits. Gains over 0dB may cause clipping if the input signal is too high. The LOUT2MUTE/ ROUT2MUTE register bits cause these outputs to be muted (the output DC level is driven out). The output pins remain at the same DC level, so that no click noise is produced when muting or un-muting. w PD, Rev 4.1, June 2009 44 WM8986 Production Data REGISTER ADDRESS R54 (36h) LOUT2 Volume control R55 (37h) ROUT2 Volume control BIT LABEL DEFAULT 111001 DESCRIPTION 5:0 LOUT2VOL Left output volume: (1dB steps) 000000 = -57dB ... 111001 = 0dB ... 111111 = +6dB 6 LOUT2MUTE 0 Left output mute: 0 = Normal operation 1 = Mute 7 LOUT2ZC 0 LOUT2 volume zero cross enable: 1 = Change gain on zero cross only 0 = Change gain immediately 8 OUT2VU Not latched LOUT2 and ROUT2 volumes do not update until a 1 is written to OUT2VU (in reg 54 or 55) 5:0 ROUT2VOL 6 111001 Right output volume: (1dB steps) 000000 = -57dB ... 111001 = 0dB ... 111111 = +6dB ROUT2MUTE 0 Right output mute: 0 = Normal operation 1 = Mute 7 ROUT2ZC 0 ROUT2 volume zero cross enable: 1 = Change gain on zero cross only 0 = Change gain immediately 8 OUT2VU Not latched LOUT2 and ROUT2 volumes do not update until a 1 is written to OUT2VU (in reg 54 or 55) Table 25 OUT2 Volume Control ZERO CROSS TIMEOUT A zero-cross timeout function is provided so that if zero cross is enabled on the input or output PGAs the gain will automatically update after a timeout period if a zero cross has not occurred. This is enabled by setting SLOWCLKEN. The timeout period is dependent on the clock input to the digital and is equal to 221 * SYSCLK period. REGISTER ADDRESS R7 (07h) Additional Control BIT 0 LABEL SLOWCLKEN DEFAULT 0 DESCRIPTION Slow clock enable. 0 = slow clock disabled 1 = slow clock enabled Table 26 Timeout Clock Enable Control Note: SLOWCLKEN is also used for the jack insert detect debounce circuit w PD, Rev 4.1, June 2009 45 WM8986 Production Data OUT3/OUT4 MIXERS AND OUTPUT STAGES The OUT3/OUT4 pins provide an additional stereo line output, a mono output, or a differential output. There is a dedicated analogue mixer for OUT3 and one for OUT4 as shown in Figure 25. The OUT3 and OUT4 output stages are powered from AVDD1 and AGND1. Figure 25 OUT3 and OUT4 Mixers OUT3 can provide a left line output, or a mono mix line output. OUT4 can provide a right line output, or a mono mix line output. A 6dB attenuation function is provided for OUT4, to prevent clipping during mixing of left and right signals. This function is enabled by the OUT4ATTN register bit. w PD, Rev 4.1, June 2009 46 WM8986 Production Data REGISTER ADDRESS R56 (38h) OUT3 mixer control R57 (39h) OUT4 mixer control BIT LABEL DEFAULT DESCRIPTION 6 OUT3MUTE 0 0 = Output stage outputs OUT3 mixer 1 = Output stage muted - drives out VMID. Can be used as VMID reference in this mode. (Not to be used for Capless HP pseudo GND) 3 OUT4_2OUT3 0 OUT4 mixer output to OUT3 0 = disabled 1 = enabled 2 BYPL2OUT3 0 Left PGA output to OUT3 0 = disabled 1 = enabled 1 LMIX2OUT3 0 Left DAC mixer to OUT3 0 = disabled 1 = enabled 0 LDAC2OUT3 1 Left DAC output to OUT3 0 = disabled 1 = enabled 7 OUT3_2OUT4 0 OUT3 mixer output to OUT4 0 = disabled 1 = enabled 6 OUT4MUTE 0 0 = Output stage outputs OUT4 mixer 1 = Output stage muted - drives out VMID. Can be used as VMID reference in this mode. (Not to be used for Capless HP pseudo GND) 5 OUT4ATTN 0 0 = OUT4 normal output 1 = OUT4 attenuated by 6dB 4 LMIX2OUT4 0 Left DAC mixer to OUT4 0 = disabled 1 = enabled 3 LDAC2OUT4 0 Left DAC to OUT4 0 = disabled 1 = enabled 2 BYPR2OUT4 0 Right PGA output to OUT4 0 = disabled 1 = enabled 1 RMIX2OUT4 0 Right DAC mixer to OUT4 0 = disabled 1 = enabled 0 RDAC2OUT4 1 Right DAC output to OUT4 0 = disabled 1 = enabled Table 27 OUT3/OUT4 Mixer Registers w PD, Rev 4.1, June 2009 47 WM8986 Production Data ENABLING THE OUTPUTS Each analogue output of the WM8986 can be independently enabled or disabled. The analogue mixer associated with each output has a separate enable bit. All outputs are disabled by default. To save power, unused parts of the WM8986 should remain disabled. Outputs can be enabled at any time, but it is not recommended to do so when BUFIO is disabled (BUFIOEN=0), as this may cause pop noise (see "Power Management" and "Applications Information" sections). REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R1 (01h) Power Management 1 2 BUFIOEN 0 Unused input/output bias buffer enable 6 OUT3MIXEN 0 OUT3 mixer enable 7 OUT4MIXEN 0 OUT4 mixer enable R2 (02h) Power Management 2 8 ROUT1EN 0 ROUT1 output enable 7 LOUT1EN 0 LOUT1 output enable 6 SLEEP 0 0 = Normal device operation 1 = Supply current reduced in device standby mode when clock supplied (see Note) R3 (03h) Power Management 3 2 LMIXEN 0 Left mixer enable 3 RMIXEN 0 Right mixer enable 5 LOUT2EN 0 LOUT2 output enable 6 ROUT2EN 0 ROUT2 output enable 7 OUT3EN 0 OUT3 enable 8 OUT4EN 0 OUT4 enable Note: All "Enable" bits are 1 = ON, 0 = OFF Table 28 Output Stages Power Management Control Note: The SLEEP bit R2[6] should only be used when the device is already in Standby mode. The SLEEP bit prevents the MCLK from propagating round the device when the external MCLK signal cannot be removed. THERMAL SHUTDOWN To protect the WM8986 from becoming too hot, a thermal sensor has been built in. If the device junction temperature reaches approximately 125C and the TSDEN and TSOPCTRL bit are set, then all outputs will be disabled to avoid further increase of the chip temperature. Additionally, when the device is too hot and TSDEN is set, then the WM8986 de-asserts GPIO bit 11, a virtual GPIO that can be set up to generate an interrupt to the CPU (see "GPIO and Interrupt Control" section). REGISTER ADDRESS R49 (31h) Output Control BIT LABEL DEFAULT DESCRIPTION 1 TSDEN 0 Thermal Sensor Enable 0 = disabled 1 = enabled 2 TSOPCTRL 0 Thermal Shutdown Output enable 0 = Disabled 1 = Enabled, i.e. all outputs will be disabled if TI set and the device junction temperature is more than 125C. Table 29 Thermal Shutdown UNUSED ANALOGUE INPUTS/OUTPUTS Whenever an analogue input/output is disabled, it remains connected to a voltage source (AVDD1/2) through a resistor. This helps to prevent pop noise when the output is re-enabled. The resistance between the voltage buffer and the output pins can be controlled using the VROI control bit. The default impedance is low, so that any capacitors on the outputs can charge up quickly at start-up. If a high impedance is desired for disabled outputs, VROI can then be set to 1, increasing the resistance to about 30k. w PD, Rev 4.1, June 2009 48 WM8986 Production Data REGISTER ADDRESS R49 (31h) BIT 0 LABEL VROI DEFAULT 0 DESCRIPTION VREF (AVDD1/2) to analogue output resistance 0 = approx 1k 1 = approx 30 k Table 30 Disabled Outputs to VREF Resistance A dedicated buffer is available for biasing unused analogue I/O pins as shown in Figure 26. This buffer can be enabled using the BUFIOEN register bit. Figure 26 summarises the bias options for the output pins. Figure 26 Unused Input/Output Pin Tie-off Buffers L/ROUT2EN/ OUT3/4EN VROI OUTPUT CONFIGURATION 0 0 1k to AVDD1/2 0 1 30k to AVDD1/2 1 X Output enabled (DC level=AVDD1/2) Table 31 Unused Output Pin Bias Options w PD, Rev 4.1, June 2009 49 WM8986 Production Data DIGITAL AUDIO INTERFACES The audio interface has three pins: * DACDAT: DAC data input * * LRC: Data Left/Right alignment clock BCLK: Bit clock, for synchronisation The clock signals BCLK, and LRC can be outputs when the WM8986 operates as a master, or inputs when it is a slave (see Master and Slave Mode Operation, below). Five different audio data formats are supported: * Left justified * * * Right justified I 2S DSP mode A * DSP mode B All of these modes are MSB first. They are described in Audio Data Formats, below. Refer to the Electrical Characteristic section for timing information. MASTER AND SLAVE MODE OPERATION The WM8986 audio interface may be configured as either master or slave. As a master interface device the WM8986 generates BCLK and LRC and thus controls sequencing of the data transfer on DACDAT. To set the device to master mode register bit MS should be set high. In slave mode (MS=0), the WM8986 responds with data to clocks it receives over the digital audio interfaces. AUDIO DATA FORMATS In Left Justified mode, the MSB is available on the first rising edge of BCLK following an LRC transition. The other bits up to the LSB are then transmitted in order. Depending on word length, BCLK frequency and sample rate, there may be unused BCLK cycles before each LRC transition. Figure 27 Left Justified Audio Interface (assuming n-bit word length) In Right Justified mode, the LSB is available on the last rising edge of BCLK before a LRC transition. All other bits are transmitted before (MSB first). Depending on word length, BCLK frequency and sample rate, there may be unused BCLK cycles after each LRC transition. Figure 28 Right Justified Audio Interface (assuming n-bit word length) w PD, Rev 4.1, June 2009 50 WM8986 Production Data In I2S mode, the MSB is available on the second rising edge of BCLK following a LRC transition. The other bits up to the LSB are then transmitted in order. Depending on word length, BCLK frequency and sample rate, there may be unused BCLK cycles between the LSB of one sample and the MSB of the next. Figure 29 I2S Audio Interface (assuming n-bit word length) In DSP/PCM mode, the left channel MSB is available on either the 1st (mode B) or 2nd (mode A) rising edge of BCLK (selectable by LRP) following a rising edge of LRC. Right channel data immediately follows left channel data. Depending on word length, BCLK frequency and sample rate, there may be unused BCLK cycles between the LSB of the right channel data and the next sample. In device master mode, the LRC output will resemble the LRC pulse shown in Figure 30 and Figure 31. In device slave mode, Figure 32 and Figure 33, it is possible to use any length of LRC pulse less than 1/fs, providing the falling edge of the LRC pulse occurs greater than one BCLK period before the rising edge of the next LRC pulse. Figure 30 DSP/PCM Mode Audio Interface (mode A, LRP=0, Master) Figure 31 DSP/PCM Mode Audio Interface (mode B, LRP=1, Master) w PD, Rev 4.1, June 2009 51 WM8986 Production Data Figure 32 DSP/PCM Mode Audio Interface (mode A, LRP=0, Slave) Figure 33 DSP/PCM Mode Audio Interface (mode B, LRP=0, Slave) w PD, Rev 4.1, June 2009 52 WM8986 Production Data REGISTER ADDRESS R4 (04h) Audio Interface Control BIT LABEL DEFAULT DESCRIPTION 0 MONO 0 Selects between stereo and mono device operation: 0 = Stereo device operation 1 = Mono device operation. Data appears in `left' phase of LRC only. 2 DLRSWAP 0 Controls whether DAC data appears in `right' or `left' phases of LRC clock: 0 = DAC left data appear in `left' phase of LRC and right data in 'right' phase 1 = DAC left data appear in `right' phase of LRC and right data in 'left' phase 4:3 FMT 10 Audio interface Data Format Select: 00 = Right Justified 01 = Left Justified 10 = I2S format 11 = DSP/PCM mode 6:5 WL 10 Word length 00 = 16 bits 01 = 20 bits 10 = 24 bits 11 = 32 bits (see note) 7 LRP 0 LRC clock polarity 0 = normal 1 =inverted DSP Mode - mode A/B select 0 = MSB is available on 2nd BCLK rising edge after LRC rising edge (mode A) 1 = MSB is available on 1st BCLK rising edge after LRC rising edge (mode B) 8 BCP 0 BCLK polarity 0 = normal 1 = inverted Table 32 Audio Interface Control Note: Right Justified Mode will only operate with a maximum of 24 bits. If 32-bit mode is selected the device will operate in 24-bit mode. AUDIO INTERFACE CONTROL The register bits controlling audio format, word length and master / slave mode are summarised below. Register bit MS selects audio interface operation in master or slave mode. In Master mode BCLK, and LRC are outputs. The frequency of BCLK in master mode can be controlled with BCLKDIV. The frequencies of BCLK and LRC are also controlled by MCLKDIV. The LRC sample rate is set to the required values by MCLKDIV and the BCLK rate will be set accordingly to provide sufficient BCLKs for that chosen sample rate. These clocks are divided down versions of master clock. w PD, Rev 4.1, June 2009 53 WM8986 Production Data REGISTER ADDRESS R6 (06h) Clock Generation Control BIT LABEL DEFAULT DESCRIPTION 0 MS 0 Sets the chip to be master over LRC and BCLK 0 = BCLK and LRC clock are inputs 1 = BCLK and LRC clock are outputs generated by the WM8986 (MASTER) 4:2 BCLKDIV 000 Configures the BCLK output frequency, for use when the chip is master over BCLK. 000 = divide by 1 (BCLK=SYSCLK) 001 = divide by 2 (BCLK=SYSCLK/2) 010 = divide by 4 (BCLK=SYSCLK/4) 011 = divide by 8 (BCLK=SYSCLK/8) 100 = divide by 16 (BCLK=SYSCLK/16) 101 = divide by 32 (BCLK=SYSCLK/32) 110 = reserved 111 = reserved 7:5 MCLKDIV 010 Sets the scaling for SYSCLK clock output (under control of CLKSEL) 000 = divide by 1 (LRC=SYSCLK/128) 001 = divide by 1.5 (LRC=SYSCLK/192) 010 = divide by 2 (LRC=SYSCLK/256) 011 = divide by 3 (LRC=SYSCLK/384) 100 = divide by 4 (LRC=SYSCLK/512) 101 = divide by 6 (LRC=SYSCLK/768) 110 = divide by 8 (LRC=SYSCLK/1024) 111 = divide by 12 (LRC=SYSCLK/1536) 8 CLKSEL 1 Controls the source of the clock for all internal operation: 0 = MCLK 1 = PLL output Table 33 Clock Control The CLKSEL bit selects the internal source of the Master clock from the PLL (CLKSEL=1) or from MCLK (CLKSEL=0). When the internal clock is switched from one source to another using the CLKSEL bit, the clock originally selected must generate at least one falling edge after CLKSEL has changed for the switching of clocks to be successful. EXAMPLE: If the PLL is the current source of the internal clock (CLKSEL=1) and it is required to switch to the MCLK, change CLKSEL to select MCLK (CLKSEL=0) and then disable PLL (PLLEN=0). AUDIO SAMPLE RATES The WM8986 DAC limiter characteristics are sample rate dependent. SR should be set to the correct sample rate or the closest value if the actual sample rate is not available. If a sample rate that is not explicitly supported by the SR register settings is required then the closest SR value to that sample rate should be chosen. The DAC limiter characteristics will scale appropriately. REGISTER ADDRESS w BIT LABEL DEFAULT DESCRIPTION PD, Rev 4.1, June 2009 54 WM8986 Production Data R7 (07h) Additional Control 3:1 SR 000 Approximate sample rate (configures the coefficients for the internal digital filters): 000 = 48kHz 001 = 32kHz 010 = 24kHz 011 = 16kHz 100 = 12kHz 101 = 8kHz 110-111 = reserved Table 45 Sample Rate Control MASTER CLOCK AND PHASE LOCKED LOOP (PLL) The WM8986 has an on-chip phase-locked loop (PLL) circuit that can be used to: Generate master clocks for the WM8986 audio functions from another external clock, e.g. in telecoms applications. Generate and output (on pin CSB/GPIO1) a clock for another part of the system that is derived from an existing audio master clock. Figure shows the PLL and internal clocking on the WM8986. The PLL can be enabled or disabled by the PLLEN register bit. REGISTER ADDRESS R1 (01h) Power management 1 BIT 5 LABEL PLLEN DEFAULT 0 DESCRIPTION PLL enable 0 = PLL off 1 = PLL on Table 46 PLLEN Control Bit Figure 38 PLL and Clock Select Circuit The PLL frequency ratio R = f2/f1 (see Figure ) can be set using the register bits PLLK and PLLN: PLLN = int R PLLK = int (224 (R-PLLN)) EXAMPLE: MCLK=12MHz, required clock = 12.288MHz. R should be chosen to ensure 5 < PLLN < 13. There is a fixed divide by 4 in the PLL and a w PD, Rev 4.1, June 2009 55 WM8986 Production Data selectable divide by N after the PLL which should be set to divide by 2 to meet this requirement. Enabling the divide by 2 sets the required f2 = 4 x 2 x 12.288MHz = 98.304MHz. R = 98.304 / 12 = 8.192 PLLN = int R = 8 k = int ( 224 x (8.192 - 8)) = 3221225 = 3126E9h w PD, Rev 4.1, June 2009 56 WM8986 Production Data REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R36 (24h) PLL N value 4 PLLPRESCALE 0 0 = MCLK input not divided (default) 1 = Divide MCLK by 2 before input to PLL 3:0 PLLN 1000 Integer (N) part of PLL input/output frequency ratio. Use values greater than 5 and less than 13. R37 (25h) PLL K value 1 5:0 PLLK [23:18] 0Ch Fractional (K) part of PLL1 input/output frequency ratio (treat as one 24-digit binary number). R38 (26h) PLL K Value 2 8:0 PLLK [17:9] 093h R39 (27h) PLL K Value 3 8:0 PLLK [8:0] 0E9h Table 47 PLL Frequency Ratio Control DESIRED OUTPUT (SYSCLK) (MHz) f2 (MHz) PLLPRESCALE MCLKDIV The PLL performs best when f2 is around 90MHz. Its stability peaks at N=8. Some example settings are shown in 48. 12 11.29 90.3168 1 2 7.5264 7h 86C226h 12 12.288 98.304 1 2 8.192 8h 3126E8h 13 11.29 90.3168 1 2 6.947446 6h 13 12.288 98.304 1 2 7.561846 7h 14.4 11.29 90.3168 1 2 6.272 14.4 12.288 98.304 1 2 19.2 11.29 90.3168 2 2 MCLK (MHz) (f1) R N K N REGISTER R36[3:0] K REGISTERS R37 R38 R39 XX7h 021h 161h 026h XX8h 00Ch 093h 0E8h F28BD4h XX6h 03Ch 145h 1D4h 8FD525h XX7h 023h 1EAh 125h 6h 45A1CAh XX6h 011h 0D0h 1CAh 6.826667 6h D3A06Eh XX6h 034h 1D0h 06Eh 9.408 9h 6872AFh XX9h 01Ah 039h 0AFh 19.2 12.288 98.304 2 2 10.24 Ah 3D70A3h XXAh 00Fh 0B8h 0A3h 19.68 11.29 90.3168 2 2 9.178537 9h 2DB492h XX9h 00Bh 0DAh 092h 19.68 12.288 98.304 2 2 9.990243 9h FD809Fh XX9h 03Fh 0C0h 09Fh 19.8 11.29 90.3168 2 2 9.122909 9h 1F76F7h XX9h 007h 1BBh 0F7h 19.8 12.288 98.304 2 2 9.929697 9h EE009Eh XX9h 03Bh 100h 09Eh 24 11.29 90.3168 2 2 7.5264 7h 86C226h XX7h 021h 161h 026h 24 12.288 98.304 2 2 8.192 8h 3126E8h XX8h 00Ch 093h 0E8h 26 11.29 90.3168 2 2 6.947446 6h F28BD4h XX6h 03Ch 145h 1D4h 26 12.288 98.304 2 2 7.561846 7h 8FD525h XX7h 023h 1EAh 125h 27 11.29 90.3168 2 2 6.690133 6h B0AC93h XX6h 02Ch 056h 093h 27 12.288 98.304 2 2 7.281778 7h 482296h XX7h 012h 011h 096h Table 48 PLL Frequency Examples w PD, Rev 4.1, June 2009 57 WM8986 Production Data COMPANDING The WM8986 supports A-law and -law companding. Companding can be enabled on the DAC audio interface by writing the appropriate value to the DAC_COMP register bit. REGISTER ADDRESS R5 (05h) Companding Control BIT LABEL DEFAULT DESCRIPTION 4:3 DAC_COMP 0 DAC companding 00 = off 01 = reserved 10 = -law 11 = A-law 5 WL8 0 0 = off 1 = device operates in 8-bit mode. Table 49 Companding Control Companding involves using a piecewise linear approximation of the following equations (as set out by ITU-T G.711 standard) for data compression: -law (where =255 for the U.S. and Japan): F(x) = ln( 1 + |x|) / ln( 1 + ) -1 x 1 law (where A=87.6 for Europe): F(x) = A|x| / ( 1 + lnA) } for x 1/A F(x) = ( 1 + lnA|x|) / (1 + lnA) } for 1/A x 1 The companded data is also inverted as recommended by the G.711 standard (all 8 bits are inverted for -law, all even data bits are inverted for A-law). The data will be transmitted as the first 8 MSB's of data. Companding converts 13 bits (-law) or 12 bits (A-law) to 8 bits using non-linear quantization. The input data range is separated into 8 levels, allowing low amplitude signals better precision than that of high amplitude signals. This is to exploit the operation of the human auditory system, where louder sounds do not require as much resolution as quieter sounds. The companded signal is an 8bit word containing sign (1-bit), exponent (3-bits) and mantissa (4-bits). Setting the WL8 register bit allows the device to operate with 8-bit data. In this mode it is possible to use 8 BCLK's per LRC frame. When using DSP mode B, this allows 8-bit data words to be output consecutively every 8 BCLK's and can be used with 8-bit data words using the A-law and u-law companding functions. BIT7 BIT[6:4] BIT[3:0] SIGN EXPONENT MANTISSA Table 50 8-bit Companded Word Composition w PD, Rev 4.1, June 2009 58 WM8986 Production Data u-law Companding 1 120 0.9 Companded Output 0.7 80 0.6 0.5 60 0.4 40 0.3 Normalised Output 0.8 100 0.2 20 0.1 0 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 Normalised Input Figure 39 -Law Companding A-law Companding 1 120 0.9 Companded Output 0.7 80 0.6 0.5 60 0.4 40 0.3 Normalised Output 0.8 100 0.2 20 0.1 0 0 0 0.2 0.4 0.6 0.8 1 Normalised Input Figure 40 A-Law Companding w PD, Rev 4.1, June 2009 59 WM8986 Production Data GENERAL PURPOSE INPUT/OUTPUT The WM8986 has one dual purpose input/output pin, CSB/GPIO1. The GPIO1 function is provided for use as jack detection input or general purpose output. The default configuration for the CSB/GPIO1 is to be an input. When setup as an input, the CSB/GPIO1 pin can either be used as CSB or for jack detection, depending on how the MODE pin is set. Table 34 illustrates the functionality of the GPIO1 pin when used as a general purpose output. REGISTER ADDRESS R8 (08h) GPIO Control BIT LABEL DEFAULT DESCRIPTION 2:0 GPIO1SEL 000 CSB/GPIO1 pin function select: 000 = input (CSB / Jack detection: depending on MODE setting) 001 = reserved 010 = Temp ok 011 = Amute active 100 = PLL clk output 101 = PLL lock 110 = logic 0 111 = logic 1 3 GPIO1POL 0 GPIO1 Polarity invert 0 = Non inverted 1 = Inverted 6 GPIO1GPD 0 GPIO1 Internal pull-down enable: 0 = Internal pull-down disabled 1 = Internal pull-down enabled 7 GPIO1GPU 0 GPIO1 Internal pull-up enable: 0 = Internal pull-up disabled 1 = Internal pull-up enabled 8 GPIO1GP 0 GPIO1 Open drain enable 0 = Open drain disabled 1 = Open drain enabled R14(0Eh) GPIO Control 5:4 OPCLKDIV 00 PLL Output clock division ratio 00 = divide by 1 01 = divide by 2 10 = divide by 3 11 = divide by 4 Table 34 CSB/GPIO Control Note: If MODE is set to 3 wire mode, CSB/GPIO1 is used as CSB input irrespective of the GPIO1SEL[2:0] bits. w PD, Rev 4.1, June 2009 60 WM8986 Production Data For further details of the jack detect operation see the OUTPUT SWITCHING section. OUTPUT SWITCHING (JACK DETECT) When the device is operated using a 2-wire interface the CSB/GPIO1 pin can be used as a switch control input to automatically disable one set of outputs and enable another; the most common use for this functionality is as jack detect circuitry. The GPIO pins have an internal de-bounce circuit when in this mode in order to prevent the output enables from toggling multiple times due to input glitches. This de-bounce circuit is clocked from a slow clock with period 221 x MCLK and is enabled by the SLOWCLKEN bit. Notes: The SLOWCLKEN bit must be enabled for the jack detect circuitry to operate. The GPIOPOL bit is not relevant for jack detection, it is the signal detected at the pin which is used Switching on/off of the outputs is fully configurable by the user. Each output, OUT1, OUT2, OUT3 and OUT4 has 2 associated enables. OUT1_EN_0, OUT2_EN_0, OUT3_EN_0 and OUT4_EN_0 are the output enable signals which are used if the selected jack detection pin is at logic 0 (after debounce). OUT1_EN_1, OUT2_EN_1, OUT3_EN_1 and OUT4_EN_1 are the output enable signals which are used if the selected jack detection pin is at logic 1 (after de-bounce). The jack detection enables operate as follows: All OUT_EN signals have an AND function performed with their normal enable signals (in Table 28). When an output is normally enabled at per Table 28, the selected jack detection enable (controlled by selected jack detection pin polarity) is set 0; it will turn the output off. If the normal enable signal is already OFF (0), the jack detection signal will have no effect due to the AND function. During jack detection if the user desires an output to be un-changed whether the jack is in or not, both the JD_EN settings, i.e. JD_EN0 and JD_EN1, should be set to 0000. If jack detection is not enabled (JD_EN=0), the output enables default to all 1's, allowing the outputs to be controlled as normal via the normal output enables found in Table 28. w PD, Rev 4.1, June 2009 61 WM8986 Production Data BIT LABEL DEFAULT DESCRIPTION REGISTER ADDRESS R9 (09h) GPIO control 6 JD_EN 0 Jack Detection Enable 0 = disabled 1 = enabled R13 (00h) 3:0 JD_EN0 0000 Output enables when selected jack detection input is logic 0. [0]= OUT1_EN_0 [1]= OUT2_EN_0 [2]= OUT3_EN_0 [3]= OUT4_EN_0 7:4 JD_EN1 0000 Output enables when selected jack detection input is logic 1 [4]= OUT1_EN_1 [5]= OUT2_EN_1 [6]= OUT3_EN_1 [7]= OUT4_EN_1 Table 35 Jack Detect Register Control Bits CONTROL INTERFACE SELECTION OF CONTROL MODE AND 2-WIRE MODE ADDRESS The control interface can operate as either a 3-wire or 2-wire control interface. The MODE pin determines the 2 or 3 wire mode as shown in Table 36. The WM8986 is controlled by writing to registers through a serial control interface. A control word consists of 16 bits. The first 7 bits (B15 to B9) are register address bits that select which control register is accessed. The remaining 9 bits (B8 to B0) are data bits, corresponding to the 9 data bits in each control register. MODE INTERFACE FORMAT Low 2 wire High 3 wire Table 36 Control Interface Mode Selection 3-WIRE SERIAL CONTROL MODE In 3-wire mode, every rising edge of SCLK clocks in one data bit from the SDIN pin. A rising edge on CSB/GPIO latches in a complete control word consisting of the last 16 bits. Figure 34 3-Wire Serial Control Interface w PD, Rev 4.1, June 2009 62 WM8986 Production Data 2-WIRE SERIAL CONTROL MODE The WM8986 supports software control via a 2-wire serial bus. Many devices can be controlled by the same bus, and each device has a unique 7-bit device address (this is not the same as the 7-bit address of each register in the WM8986). The WM8986 operates as a slave device only. The controller indicates the start of data transfer with a high to low transition on SDIN while SCLK remains high. This indicates that a device address and data will follow. All devices on the 2-wire bus respond to the start condition and shift in the next eight bits on SDIN (7-bit address + Read/Write bit, MSB first). If the device address received matches the address of the WM8986, the WM8986 responds by pulling SDIN low on the next clock pulse (ACK). If the address is not recognised or the R/W bit is `1' when operating in write only mode, the WM8986 returns to the idle condition and waits for a new start condition and valid address. During a write, once the WM8986 has acknowledged a correct address, the controller sends the first byte of control data (B15 to B8, i.e. the WM8986 register address plus the first bit of register data). The WM8986 then acknowledges the first data byte by driving SDIN low for one clock cycle. The controller then sends the second byte of control data (B7 to B0, i.e. the remaining 8 bits of register data), and the WM8986 acknowledges again by pulling SDIN low. Transfer is complete when there is a low to high transition on SDIN while SCLK is high. After a complete sequence the WM8986 returns to the idle state and waits for another start condition. If a start or stop condition is detected out of sequence at any point during data transfer (i.e. SDIN changes while SCLK is high), the control interface returns to the idle condition. DEVICE ADDRESS (7 BITS) SDIN RD / WR BIT ACK (LOW) CONTROL BYTE 1 (BITS 15 TO 8) ACK (LOW) CONTROL BYTE 1 (BITS 7 TO 0) ACK (LOW) SCLK START register address and 1st register data bit remaining 8 bits of register data STOP Figure 35 2-Wire Serial Control Interface In 2-wire mode the WM8986 has a fixed device address, 0011010. RESETTING THE CHIP The WM8986 can be reset by performing a write of any value to the software reset register (address 0h). This will cause all register values to be reset to their default values. In addition to this there is a Power-On Reset (POR) circuit which ensures that the registers are initially set to default when the device is powered up. POWER SUPPLIES The WM8986 requires four separate power supplies: AVDD1 and AGND1: Analogue supply, powers all internal analogue functions and output drivers LOUT1, ROUT1, OUT3 and OUT4. AVDD1 must be between 2.5V and 3.6V and has the most significant impact on overall power consumption (except for power consumed in the headphones). Higher AVDD1 will improve audio quality. AVDD2 and AGND2: Output driver supplies, power LOUT2 and ROUT2. AVDD2 must be between 2.5V and 3.6V. AVDD2 can be tied to AVDD1, but it requires separate layout and decoupling capacitors to curb harmonic distortion. DCVDD: Digital core supply, powers all digital functions except the audio and control interface pads. DCVDD must be between 1.71V and 3.6V, and has no effect on audio quality. The return path for DCVDD is DGND, which is shared with DBVDD. DBVDD must be between 1.71V and 3.6V. DBVDD return path is through DGND. It is possible to use the same supply voltage for all four supplies. However, digital and analogue supplies should be routed and decoupled separately on the PCB to keep digital switching noise out of the analogue signal paths. w PD, Rev 4.1, June 2009 63 WM8986 Production Data POWER MANAGEMENT SAVING POWER BY REDUCING OVERSAMPLING RATE The default mode of operation of the DAC digital filters is in 64x oversampling mode. Under the control of DACOSR128 the oversampling rate may be doubled. 64x oversampling results in a slight decrease in noise performance compared to 128x but lowers the power consumption of the device. REGISTER ADDRESS R10 (0Ah) DAC control BIT LABEL 3 DEFAULT DACOSR128 0 DESCRIPTION DAC oversample rate select 0 = 64x (lowest power) 1 = 128x (best SNR) Table 37 DAC Oversampling Rate Selection LOW POWER MODE If only limited functionality is required, the WM8986 can be put into a low power mode. In this mode, the DSP core runs at half of the normal rate, reducing digital power consumption of the core by half. For DAC low power only, 3D enhancement with 2-Band equaliser functionality is permitted, where only Band 1 (low shelf) and Band 5 (high shelf) can be used. . REGISTER ADDRESS R7 (07h) Additional Ctrl BIT LABEL 8 DEFAULT M128ENB 0 DESCRIPTION 0 = low power mode enabled 1 = low power mode disabled Table 38 DSP Core Low Power Mode Control The register settings for this low-power mode are detailed below. The device will not enter low power unless in this register configuration, regardless of M128ENB. For pop-free operation of the device it is recommended to change the M128ENB low power functionality only when both DACs are disabled, i.e. when DACENL=0 and DACENR=0. FUNCTION DAC low power REGISTER BITS SETTING M128ENB DACENL DACENR 0 1 1 DESCRIPTION Either or both of DACENL and DACENR must be set (mono or stereo mode) Table 39 DSP Core Low Power Mode Register Settings VMID The analogue circuitry will not operate unless VMID is enabled. The impedance of the VMID resistor string, together with the decoupling capacitor on the VMID pin will determine the start-up time of the VMID circuit. REGISTER ADDRESS R1 (01h) Power management 1 BIT 1:0 LABEL DEFAULT VMIDSEL 00 DESCRIPTION Reference string impedance to VMID pin 00= off (250k VMID to AGND1) 01=75k 10=300k 11=5k Table 40 VMID Impedance Control BIASEN The analogue amplifiers will not operate unless BIASEN is enabled. REGISTER ADDRESS R1 (01h) Power management 1 BIT 3 LABEL BIASEN DEFAULT 0 DESCRIPTION Analogue amplifier bias control 0 = disabled 1 = enabled Table 41 Analogue Bias Control w PD, Rev 4.1, June 2009 64 WM8986 Production Data REGISTER MAP ADDR B[15:9] REGISTER NAME B8 B7 B6 B5 B4 B3 B2 B1 B0 DEC HEX DEFAULT VAL (HEX) 0 00 Software Reset 1 01 Power manage't 1 0 2 02 Power manage't 2 ROUT1EN LOUT1EN 3 03 Power manage't 3 OUT4EN OUT3EN ROUT2EN LOUT2EN 4 04 Audio Interface BCP LRP 5 05 Companding ctrl 0 0 6 06 Clock Gen ctrl CLKSEL 7 07 Additional ctrl M128ENB 8 08 GPIO Control GPIO1GP 0 0 GPIO1POL 9 09 Jack detect control 0 0 JD_EN 0 0 0 0 10 0A DAC Control 0 0 SOFT MUTE 0 0 DACOSR 128 AMUTE 11 0B Left DAC digital Vol DACVU DACLVOL[7:0] 12 0C Right DAC dig'l Vol DACVU DACRVOL[7:0] 13 0D Jack Detect Control 0 14 0E GPIO Control 0 15 0F Reserved 000000000 16 10 Reserved 000000000 18 12 EQ1 - low shelf EQ3DEN 0 EQ1C[1:0] EQ1G[4:0] 12C 19 13 EQ2 - peak 1 EQ2BW 0 EQ2C[1:0] EQ2G[4:0] 02C 20 14 EQ3 - peak 2 EQ3BW 0 EQ3C[1:0] EQ3G[4:0] 02C 21 15 EQ4 - peak 3 EQ4BW 0 EQ4C[1:0] EQ4G[4:0] 02C 22 16 EQ5 - high shelf 0 0 EQ5C[1:0] EQ5G[4:0] 23 17 Class D Control CLASSDEN 0 24 18 DAC Limiter 1 LIMEN 25 19 DAC Limiter 2 0 27 1B Reserved 000000000 000 28 1C Reserved 000000000 000 29 1D Reserved 000000000 000 30 1E Reserved 000000000 000 32 20 Reserved 000000000 000 33 21 Reserved 000000000 000 34 22 Reserved 000000000 000 35 23 Reserved 000000000 36 24 PLL N 0 0 0 37 25 PLL K 1 0 0 0 38 26 PLL K 2 PLLK[17:9] 093 39 27 PLL K 3 PLLK[8:0] 0E9 41 29 3D control 0 0 0 0 0 42 2A Biasing 0 0 0 0 0 0 POBCTRL 0 0 000 43 2B Beep control BYPL2 RMIX BYPR2 LMIX 0 0 0 0 0 0 0 000 44 2C Input ctrl 0 0 0 RIN2 INPPGA RIP2 INPPGA 0 0 LIN2 INPPGA LIP2 INPPGA 003 w Software reset OUT4MIX OUT3MIX EN EN SLEEP PLLEN 0 BIASEN BUFIOEN VMIDSEL [1:0] 000 BOOST ENR BOOST ENL INPGA ENR INPPGA ENL 0 0 000 0 RMIXEN 000 LMIXEN DACENR DACENL FMT[1:0] DLRSWAP 0 MONO 050 DAC_COMP [1:0] 0 0 0 000 MS 140 SLOWCLK EN 080 WL[1:0] 0 WL8 MCLKDIV[2:0] BCLKDIV[2:0] 0 DCLKDIV[3:0] GPIO1GPU GPIO1GPD SR[2:0] 0 0 0 0 000 000 0 0 000 000 000 0 02C 10 LIMLVL[2:0] 0 DACRPOL DACLPOL 000 0FF 0 0 008 LIMATK[3:0] 032 LIMBOOST[3:0] 000 LIMDCY[3:0] 0 0 JD_EN0[3:0] OPCLKDIV[1:0] 0 0 0FF JD_EN1[3:0] 0 000 GPIO1SEL[2:0] 000 PLLPRE SCALE 008 PLLN[3:0] 00C PLLK[23:18] 000 DEPTH3D[3:0] PD, Rev 4.1, June 2009 65 WM8986 ADDR B[15:9] Production Data REGISTER NAME B8 B7 B6 B5 B4 B3 B2 B1 B0 DEC HEX DEFAULT VAL (HEX) 45 2D Left INP PGA gain ctrl INPGAVU INPPGA ZCL INPPGA MUTEL INPPGAVOLL[5:0] 010 46 2E Right INP PGA gain ctrl INPGAVU INPPGA ZCR INPPGA MUTER INPPGAVOLR[5:0] 010 47 2F Left Input BOOST control PGA BOOSTL 0 0 0 0 0 AUXL2BOOSTVOL[2:0] 100 48 30 PGA Right Input BOOST control BOOSTR 0 0 0 0 0 AUXR2BOOSTVOL[2:0] 100 49 31 Output ctrl 0 DACL2 RMIX DACR2 LMIX 0 0 50 32 Left mixer ctrl AUXLMIXVOL[2:0] AUXL2 LMIX 51 33 Right mixer ctrl AUXRMIXVOL[2:0] AUXR2 RMIX 52 34 LOUT1 (HP) volume ctrl OUT1VU LOUT1ZC LOUT1 MUTE LOUT1VOL[5:0] 039 53 35 ROUT1 (HP) volume ctrl OUT1VU ROUT1ZC ROUT1 MUTE ROUT1VOL[5:0] 039 54 36 LOUT2 (SPK) volume ctrl OUT2VU LOUT2ZC LOUT2 MUTE LOUT2VOL[5:0] 039 55 37 ROUT2 (SPK) volume ctrl OUT2VU ROUT2ZC ROUT2 MUTE ROUT2VOL[5:0] 039 56 38 OUT3 mixer ctrl 0 0 OUT3 MUTE 0 0 OUT4_ 2OUT3 BYPL2 OUT3 LMIX2 OUT3 LDAC2 OUT3 001 57 39 OUT4 (MONO) mixer ctrl 0 OUT 3_2OUT4 OUT4 MUTE OUT4 ATTN LMIX2 OUT4 LDAC2 OUT4 BYPR2 OUT4 RMIX2 OUT4 RDAC2 OUT4 001 61 3D Bias Control BIASCUT 0 0 0 0 TSDEN VROI 002 BYPLMIXVOL[2:0] BYPL2 LMIX DACL2 LMIX 001 BYPRMIXVOL[2:0] BYPR2 RMIX DACR2 RMIX 001 00 TSOP CTRL 00 0 000 Table 42 WM8986 Register Map w PD, Rev 4.1, June 2009 66 WM8986 Production Data REGISTER BITS BY ADDRESS Notes: 1. Default values of N/A indicate non-latched data bits (e.g. software reset or volume update bits). 2. Register bits marked as "Reserved" should not be changed from the default. REGISTER ADDRESS BIT 0 (00h) [8:0] 1 (01h) 8 LABEL RESET DESCRIPTION REFER TO N/A Software reset Resetting the Chip 0 Reserved Analogue Outputs 7 OUT4MIXEN 0 OUT4 mixer enable 0=disabled 1=enabled Power Management 6 OUT3MIXEN 0 OUT3 mixer enable 0=disabled 1=enabled Power Management 5 PLLEN 0 PLL enable 0=PLL off 1=PLL on Master Clock and Phase Locked Loop (PLL) 0 Reserved 3 BIASEN 0 Analogue amplifier bias control 0=disabled 1=enabled Power Management 2 BUFIOEN 0 Unused input/output tie off buffer enable 0=disabled 1=enabled Power Management 1:0 VMIDSEL 00 Reference string impedance to VMID pin 00= off (250k VMID to AGND1) 01=75k 10=300k 11=5k Power Management 8 ROUT1EN 0 ROUT1 output enable 0=disabled 1=enabled Power Management 7 LOUT1EN 0 LOUT1 output enable 0=disabled 1=enabled Power Management 6 SLEEP 0 0 = normal device operation 1 = residual current reduced in device standby mode (Device must be in standby mode before setting this bit) Power Management 5 BOOSTENR 0 Right channel Input BOOST enable 0 = Boost stage OFF 1 = Boost stage ON Power Management 4 BOOSTENL 0 Left channel Input BOOST enable 0 = Boost stage OFF 1 = Boost stage ON Power Management 3 INPPGAENR 0 Right channel input PGA enable 0 = disabled 1 = enabled Power Management 2 INPPGAENL 0 Left channel input PGA enable 0 = disabled 1 = enabled Power Management 1 0 Reserved 0 0 Reserved 4 2 (02h) DEFAULT w PD, Rev 4.1, June 2009 67 WM8986 REGISTER ADDRESS 3 (03h) Production Data BIT LABEL REFER TO OUT4EN 0 OUT4 enable 0 = disabled 1 = enabled Power Management 7 OUT3EN 0 OUT3 enable 0 = disabled 1 = enabled Power Management 6 ROUT2EN 0 ROUT2 enable 0 = disabled 1 = enabled Power Management 5 LOUT2EN 0 LOUT2 enable 0 = disabled 1 = enabled Power Management 0 Reserved 3 RMIXEN 0 Right output channel mixer enable: 0 = disabled 1 = enabled Analogue Outputs 2 LMIXEN 0 Left output channel mixer enable: 0 = disabled 1 = enabled Analogue Outputs 1 DACENR 0 Right channel DAC enable 0 = DAC disabled 1 = DAC enabled Analogue Outputs 0 DACENL 0 Left channel DAC enable 0 = DAC disabled 1 = DAC enabled Analogue Outputs 8 BCP 0 BCLK polarity 0=normal 1=inverted Digital Audio Interfaces 7 LRP 0 LRC clock polarity 0=normal 1=inverted Digital Audio Interfaces 6:5 WL 10 Word length 00=16 bits 01=20 bits 10=24 bits 11=32 bits Digital Audio Interfaces 4:3 FMT 10 Audio interface Data Format Select: 00=Right Justified 01=Left Justified 10=I2S format 11= DSP/PCM mode Digital Audio Interfaces 2 DLRSWAP 0 Controls whether DAC data appears in `right' or `left' phases of LRC clock: 0=DAC data appear in `left' phase of LRC 1=DAC data appears in `right' phase of LRC Digital Audio Interfaces 0 Reserved MONO 0 Selects between stereo and mono device operation: 0=Stereo device operation 1=Mono device operation. Data appears in `left' phase of LRC 000 Reserved 1 0 5 (05h) DESCRIPTION 8 4 4 (04h) DEFAULT 8:6 w Digital Audio Interfaces PD, Rev 4.1, June 2009 68 WM8986 Production Data REGISTER ADDRESS BIT LABEL REFER TO WL8 0 Companding Control 8-bit mode 0=off 1=device operates in 8-bit mode Digital Audio Interfaces 4:3 DAC_COMP 00 DAC companding 00=off (linear mode) 01=reserved 10=-law 11=A-law Digital Audio Interfaces 000 Reserved 8 CLKSEL 1 Controls the source of the clock for all internal operation: 0=MCLK 1=PLL output Digital Audio Interfaces 7:5 MCLKDIV 010 Sets the scaling for either the MCLK or PLL clock output (under control of CLKSEL) 000=divide by 1 001=divide by 1.5 010=divide by 2 011=divide by 3 100=divide by 4 101=divide by 6 110=divide by 8 111=divide by 12 Digital Audio Interfaces 4:2 BCLKDIV 000 Configures the BCLK output frequency, for use when the chip is master over BCLK. 000=divide by 1 (BCLK=MCLK) 001=divide by 2 (BCLK=MCLK/2) 010=divide by 4 011=divide by 8 100=divide by 16 101=divide by 32 110=reserved 111=reserved Digital Audio Interfaces 1 7 (07h) DESCRIPTION 5 2:0 6 (06h) DEFAULT 0 Reserved 0 MS 0 Sets the chip to be master over LRC and BCLK 0=BCLK and LRC clock are inputs 1=BCLK and LRC clock are outputs generated by the WM8978 (MASTER) Digital Audio Interfaces 8 M128ENB 0 0 = low power mode enabled 1 = low power mode disabled Additional Control 7:4 DCLKDIV 1000 Controls clock division from SYSCLK to generate suitable class D clock. Recommended class D clock frequency = 1.4MHz. 0000 = divide by 1 0010 = divide by 2 0011 = divide by 3 0100 = divide by 4 0101 = divide by 5.5 0110 = divide by 6 1000 = divide by 8 1001 = divide by 12 1010 = divide by 16 Class A / D Headphone Outputs w PD, Rev 4.1, June 2009 69 WM8986 REGISTER ADDRESS 8 (08h) 9 (09h) Production Data BIT LABEL DESCRIPTION REFER TO 3:1 SR 000 Approximate sample rate (configures the coefficients for the internal digital filters): 000=48kHz 001=32kHz 010=24kHz 011=16kHz 100=12kHz 101=8kHz 110-111=reserved Audio Sample Rates 0 SLOWCLKEN 0 Slow clock enable. Used for both the jack insert detect debounce circuit and the zero cross timeout. 0 = slow clock disabled 1 = slow clock enabled Analogue Outputs 8 GPIO1GP 0 GPIO1 Open drain enable 0 = Open drain disabled 1 = Open drain enabled General Purpose Input/Output (GPIO) 7 GPIO1GPU 0 GPIO1 Internal pull-up enable: 0 = Internal pull-up disabled 1 = Internal pull-up enabled General Purpose Input/Output (GPIO) 6 GPIO1GPD 0 GPIO1 Internal pull-down enable: 0 = Internal pull-down disabled 1 = Internal pull-down enabled General Purpose Input/Output (GPIO) 3 GPIO1POL 0 GPIO1 Polarity invert 0=Non inverted 1=Inverted General Purpose Input/Output (GPIO) 2:0 GPIO1SEL [2:0] 000 CSB/GPIO1 pin function select: 000= input (CSB/jack detection: depending on MODE setting) 001= reserved 010=Temp ok 011=Amute active 100=PLL clk o/p 101=PLL lock 110=logic 1 111=logic 0 General Purpose Input/Output (GPIO) 00 Reserved 0 Jack Detection Enable 0=disabled 1=enabled Output Switching (Jack Detect) 000000 Reserved Output Switching (Jack Detect) 00 Reserved 0 Softmute enable: 0=Disabled 1=Enabled 00 Reserved 0 DAC oversample rate select 0 = 64x (lowest power) 1 = 128x (best SNR) 8:7 6 JD_EN 5:0 10 (0Ah) DEFAULT 8:7 6 SOFTMUTE 5:4 3 DACOSR128 w Output Signal Path Power Management PD, Rev 4.1, June 2009 70 WM8986 Production Data REGISTER ADDRESS 11 (0Bh) 12 (0Ch) 13 (0Dh) 14 (0Eh) BIT LABEL DEFAULT DESCRIPTION 2 AMUTE 0 Automute enable 0 = Amute disabled 1 = Amute enabled Output Signal Path 1 DACPOLR 0 Right DAC output polarity: 0 = non-inverted 1 = inverted (180 degrees phase shift) Output Signal Path 0 DACPOLL 0 Left DAC output polarity: 0 = non-inverted 1 = inverted (180 degrees phase shift) Output Signal Path 8 DACVU N/A DAC left and DAC right volume do not update until a 1 is written to DACVU (in reg 11 or 12) Digital to Analogue Converter (DAC) 7:0 DACVOLL 11111111 Left DAC Digital Volume Control 0000 0000 = Digital Mute 0000 0001 = -127dB 0000 0010 = -126.5dB ... 0.5dB steps up to 1111 1111 = 0dB Digital to Analogue Converter (DAC) 8 DACVU N/A DAC left and DAC right volume do not update until a 1 is written to DACVU (in reg 11 or 12) Output Signal Path 7:0 DACVOLR 11111111 Right DAC Digital Volume Control 0000 0000 = Digital Mute 0000 0001 = -127dB 0000 0010 = -126.5dB ... 0.5dB steps up to 1111 1111 = 0dB Output Signal Path 8 0 Reserved 7:4 JD_EN1 0000 Output enabled when selected jack detection input is logic 1 [4]= OUT1_EN_1 [5]= OUT2_EN_1 [6]= OUT3_EN_1 [7]= OUT4_EN_1 Output Switching (Jack Detect) 3:0 JD_EN0 0000 Output enabled when selected jack detection input is logic 0. [0]= OUT1_EN_0 [1]= OUT2_EN_0 [2]= OUT3_EN_0 [3]= OUT4_EN_0 Output Switching (Jack Detect) 5:4 OPCLKDIV 00 PLL Output clock division ratio 00 = divide by 1 01 = divide by 2 10 = divide by 3 11 = divide by 4 General Purpose Input/Output (GPIO) 15 (0Fh) 8:0 000000000 Reserved 16 (10h) 8:0 000000000 Reserved 18 (12h) REFER TO 8:7 6:5 EQ1C 00 Reserved EQ3DEN 01 EQ Band 1 Cut-off Frequency: Output Signal Path 00=80Hz 01=105Hz 10=135Hz 11=175Hz 4:0 EQ1G w 01100 EQ Band 1 Gain Control. See Table 20 for details. Output Signal Path PD, Rev 4.1, June 2009 71 WM8986 REGISTER ADDRESS 19 (13h) Production Data BIT 8 LABEL EQ2BW 7 6:5 EQ2C DEFAULT DESCRIPTION REFER TO 0 EQ Band 2 Bandwidth Control 0=narrow bandwidth 1=wide bandwidth Output Signal Path 0 Reserved Output Signal Path 01 EQ Band 2 Centre Frequency: Output Signal Path 00=230Hz 01=300Hz 10=385Hz 11=500Hz 20 (14h) 4:0 EQ2G 01100 EQ Band 2 Gain Control. See Table 20 for details. Output Signal Path 8 EQ3BW 0 EQ Band 3 Bandwidth Control 0=narrow bandwidth 1=wide bandwidth Output Signal Path 0 Reserved Output Signal Path 01 EQ Band 3 Centre Frequency: Output Signal Path 7 6:5 EQ3C 00=650Hz 01=850Hz 10=1.1kHz 11=1.4kHz 21 (15h) 4:0 EQ3G 01100 EQ Band 3 Gain Control. See Table 20 for details. Output Signal Path 8 EQ4BW 0 EQ Band 4 Bandwidth Control 0=narrow bandwidth 1=wide bandwidth Output Signal Path 0 Reserved Output Signal Path 01 EQ Band 4 Centre Frequency: Output Signal Path 7 6:5 EQ4C 00=1.8kHz 01=2.4kHz 10=3.2kHz 11=4.1kHz 4:0 22 (16h) EQ4G 8:7 6:5 EQ5C 01100 EQ Band 4 Gain Control. See Table 20 for details. Output Signal Path 0 Reserved Output Signal Path 01 EQ Band 5 Cut-off Frequency: Output Signal Path 00=5.3kHz 01=6.9kHz 10=9kHz 11=11.7kHz 4:0 EQ5G 01100 EQ Band 5 Gain Control. See Table 20 for details. Output Signal Path 23 (17h) 8 CLASSDEN 0 Enable signal for class D mode on LOUT2 and ROUT2 0 = Class AB mode 1 = Class D mode Class D Control 000 0000 Reserved. Initialise to 0 24 (18h) 8 0 Enable the DAC digital limiter: 0=disabled 1=enabled 7:0 LIMEN w Output Signal Path PD, Rev 4.1, June 2009 72 WM8986 Production Data REGISTER ADDRESS BIT 7:4 LABEL LIMDCY DEFAULT 0011 DESCRIPTION REFER TO DAC Limiter Decay time (per 6dB gain change) for 44.1kHz sampling. Note that these will scale Output Signal Path with sample rate: 0000=750us 0001=1.5ms 0010=3ms 0011=6ms 0100=12ms 0101=24ms 0110=48ms 0111=96ms 1000=192ms 1001=384ms 1010=768ms 3:0 LIMATK 0010 DAC Limiter Attack time (per 6dB gain change) for 44.1kHz sampling. Note that these will scale with sample rate. Output Signal Path 0000=94us 0001=188s 0010=375us 0011=750us 0100=1.5ms 0101=3ms 0110=6ms 0111=12ms 1000=24ms 1001=48ms 1010=96ms 1011 to 1111=192ms 25 (19h) 8:7 6:4 LIMLVL 00 Reserved 000 Programmable signal threshold level (determines level at which the DAC limiter starts to operate) Output Signal Path 000=-1dB 001=-2dB 010=-3dB 011=-4dB 100=-5dB 101 to 111=-6dB 3:0 LIMBOOST 0000 DAC Limiter volume boost (can be used as a stand alone volume boost when LIMEN=0): 0000=0dB Output Signal Path 0001=+1dB 0010=+2dB ... (1dB steps) 1011=+11dB 1100=+12dB 1101 to 1111=reserved 27 (1Bh) 8:0 000000000 Reserved 28 (1Ch) 8:0 000000000 Reserved 29 (1Dh) 8:0 000000000 Reserved 30 (1Eh) 8:0 000000000 Reserved 32 (20h) 8:0 000000000 Reserved 33 (21h) 8:0 000000000 Reserved w 8 PD, Rev 4.1, June 2009 73 WM8986 REGISTER ADDRESS Production Data BIT LABEL DEFAULT DESCRIPTION 34 (22h) 8:0 000000000 Reserved 35 (23h) 8:0 000000000 Reserved 36 (24h) 8:5 0000 Reserved 37 (25h) REFER TO 4 PLL PRESCALE 0 Divide MCLK by 2 before input to PLL Master Clock and Phase Locked Loop (PLL) 3:0 PLLN[3:0] 1000 Integer (N) part of PLL input/output frequency ratio. Use values greater than 5 and less than 13. Master Clock and Phase Locked Loop (PLL) 8:6 000 Reserved 5:0 PLLK[23:18] 01100 Fractional (K) part of PLL1 input/output frequency ratio (treat as one 24-digit binary number). Master Clock and Phase Locked Loop (PLL) 38 (26h) 8:0 PLLK[17:9] 010010011 Fractional (K) part of PLL1 input/output frequency ratio (treat as one 24-digit binary number). Master Clock and Phase Locked Loop (PLL) 39 (27h) 8:0 PLLK[8:0] 011101001 Fractional (K) part of PLL1 input/output frequency ratio (treat as one 24-digit binary number). Master Clock and Phase Locked Loop (PLL) 41 (29h) 8:4 00000 Reserved DEPTH3D 0000 Stereo depth 0000: 0% (minimum 3D effect) 0001: 6.67% .... 1110: 93.3% 1111: 100% (maximum 3D effect) 3D Stereo Enhancement Analogue Outputs 3:0 42 (2Ah) 8:3 0000 00 Reserved POBCTRL 0 VMID independent current bias control 0 = Disable VMID independent current bias 1 = Enable VMID independent current bias 00 Reserved 8 BYPL2RMIX 0 Left channel input PGA stage to right output mixer 0 = not selected 1 = selected Analogue Outputs 7 BYPR2LMIX 0 Right channel input PGA stage to Left output mixer 0 = not selected 1 = selected Analogue Outputs 8 0 Reserved 7 0 Reserved 6 0 Reserved 1 Connect RIN pin to right channel input PGA negative terminal. 0=RIN not connected to input PGA 1=RIN connected to right channel input PGA amplifier negative terminal. 2 1:0 43 (2Bh) 44 (2Ch) 5 RIN2INPPGA w Input Signal Path PD, Rev 4.1, June 2009 74 WM8986 Production Data REGISTER ADDRESS BIT 4 45 (2Dh) 46 (2Eh) LABEL RIP2INPPGA DEFAULT DESCRIPTION REFER TO 1 Connect RIP pin to right channel input PGA amplifier positive terminal. 0 = RIP not connected to input PGA 1 = right channel input PGA amplifier positive terminal connected to RIP (constant input impedance) 3 0 Reserved 2 0 Reserved Input Signal Path 1 LIN2INPPGA 1 Connect LIN pin to left channel input PGA negative terminal. 0=LIN not connected to input PGA 1=LIN connected to input PGA amplifier negative terminal. Input Signal Path 0 LIP2INPPGA 1 Connect LIP pin to left channel input PGA amplifier positive terminal. 0 = LIP not connected to input PGA 1 = input PGA amplifier positive terminal connected to LIP (constant input impedance) Input Signal Path 8 INPPGAU N/A INPPGAVOLL and INPPGAVOLR volume do not update until a 1 is written to INPPGAUPDATE (in reg 45 or 46) Input Signal Path 7 INPPGAZCL 0 Left channel input PGA zero cross enable: 0=Update gain when gain register changes 1=Update gain on 1st zero cross after gain register write. Input Signal Path 6 INPPGAMUTEL 0 Mute control for left channel input PGA: 0=Input PGA not muted, normal operation 1=Input PGA muted (and disconnected from the following input BOOST stage). Input Signal Path 5:0 INPPGAVOLL 010000 Left channel input PGA volume 000000 = -12dB 000001 = -11.25db . 010000 = 0dB . 111111 = 35.25dB Input Signal Path 8 INPPGAU N/A INPPGAVOLL and INPPGAVOLR volume do not update until a 1 is written to INPPGAUPDATE (in reg 45 or 46) Input Signal Path 7 INPPGAZCR 0 Right channel input PGA zero cross enable: 0=Update gain when gain register changes 1=Update gain on 1st zero cross after gain register write. Input Signal Path 6 INPPGAMUTER 0 Mute control for right channel input PGA: 0=Input PGA not muted, normal operation 1=Input PGA muted (and disconnected from the following input BOOST stage). Input Signal Path 5:0 INPPGAVOLR 010000 Right channel input PGA volume 000000 = -12dB 000001 = -11.25db . 010000 = 0dB . 111111 = +35.25dB Input Signal Path w PD, Rev 4.1, June 2009 75 WM8986 REGISTER ADDRESS 47 (2Fh) Production Data BIT 8 LABEL 00000 Reserved 2:0 AUXL2BOOSTVOL 000 Controls the auxilliary amplifer to the left channel input boost stage: 000=Path disabled (disconnected) 001=-12dB gain through boost stage 010=-9dB gain through boost stage ... 111=+6dB gain through boost stage Input Signal Path 8 PGABOOSTR 1 Boost enable for right channel input PGA: 0 = PGA output has +0dB gain through input BOOST stage. 1 = PGA output has +20dB gain through input BOOST stage. Input Signal Path 00000 Reserved AUXR2BOOSTVOL 000 Controls the auxilliary amplifer to the right channel input boost stage: 000=Path disabled (disconnected) 001=-12dB gain through boost stage 010=-9dB gain through boost stage ... 111=+6dB gain through boost stage 2:0 8:7 Boost enable for left channel input PGA: 0 = PGA output has +0dB gain through input BOOST stage. 1 = PGA output has +20dB gain through input BOOST stage. Input Signal Path Input Signal Path 00 Reserved 6 DACL2RMIX 0 Left DAC output to right output mixer 0 = not selected 1 = selected Analogue Outputs 5 DACR2LMIX 0 Right DAC output to left output mixer 0 = not selected 1 = selected Analogue Outputs 4:3 50 (32h) REFER TO 1 7:3 49 (31h) DESCRIPTION PGABOOSTL 7:3 48 (30h) DEFAULT 00 Reserved. Initialise to 0 2 TSOPCTRL 0 Thermal Shutdown Output enable 0 = Disabled 1 = Enabled, i.e. all outputs will be disabled if TI set and the device junction temperature is more than 125C. Analogue Outputs 1 TSDEN 1 Thermal Shutdown Enable 0 : thermal shutdown disabled 1 : thermal shutdown enabled Analogue Outputs 0 VROI 0 VREF (AVDD/2 or 1.5xAVDD/2) to analogue output resistance 0: approx 1k 1: approx 30 k Analogue Outputs 8:6 AUXLMIXVOL 000 Aux left channel input to left mixer volume control: 000 = -15dB 001 = -12dB ... 101 = 0dB 110 = +3dB 111 = +6dB Analogue Outputs w PD, Rev 4.1, June 2009 76 WM8986 Production Data REGISTER ADDRESS 51 (33h) 52 (34h) BIT LABEL DEFAULT DESCRIPTION REFER TO 5 AUXL2LMIX 0 Left Auxilliary input to left channel output mixer: 0 = not selected 1 = selected Analogue Outputs 4:2 BYPLMIXVOL 000 Volume control for left input PGA to left output mixer: 000 = -15dB 001 = -12dB ... 101 = 0dB 110 = +3dB 111 = +6dB Analogue Outputs 1 BYPL2L MIX 0 Left channel input boost output to left output mixer 0 = not selected 1 = selected Analogue Outputs 0 DACL2L MIX 1 Left DAC output to left output mixer 0 = not selected 1 = selected Analogue Outputs 8:6 AUXRMIXVOL 000 Aux right channel input to right mixer volume control: 000 = -15dB 001 = -12dB ... 101 = 0dB 110 = +3dB 111 = +6dB Analogue Outputs 5 AUXR2RMIX 0 Right Auxilliary input to right channel output mixer: 0 = not selected 1 = selected Analogue Outputs 4:2 BYPRMIXVOL 000 Volume control for right channel input PAG to right output channel mixer: 000 = -15dB 001 = -12dB ... 101 = 0dB 110 = +3dB 111 = +6dB Analogue Outputs 1 BYPR2RMIX 0 Right channel input boost output to right output mixer 0 = not selected 1 = selected Analogue Outputs 0 DACR2RMIX 1 Right DAC output to right output mixer 0 = not selected 1 = selected Analogue Outputs 8 OUT1VU N/A LOUT1 and ROUT1 volumes do not update until a 1 is written to OUT1VU (in reg 52 or 53) Analogue Outputs 7 LOUT1ZC 0 Headphone volume zero cross enable: 1 = Change gain on zero cross only 0 = Change gain immediately Analogue Outputs 6 LOUT1MUTE 0 Left headphone output mute: 0 = Normal operation 1 = Mute Analogue Outputs w PD, Rev 4.1, June 2009 77 WM8986 REGISTER ADDRESS 53 (35h) 54 (36h) 55 (37h) 56 (38h) Production Data BIT LABEL DEFAULT DESCRIPTION REFER TO 5:0 LOUT1VOL 111001 Left headphone output volume: 000000 = -57dB ... 111001 = 0dB ... 111111 = +6dB Analogue Outputs 8 OUT1VU N/A LOUT1 and ROUT1 volumes do not update until a 1 is written to OUT1VU (in reg 52 or 53) Analogue Outputs 7 ROUT1ZC 0 Headphone volume zero cross enable: 1 = Change gain on zero cross only 0 = Change gain immediately Analogue Outputs 6 ROUT1MUTE 0 Right headphone output mute: 0 = Normal operation 1 = Mute Analogue Outputs 5:0 ROUT1VOL 111001 Right headphone output volume: 000000 = -57dB ... 111001 = 0dB ... 111111 = +6dB Analogue Outputs 8 OUT2VU N/A LOUT2 and ROUT2 volumes do not update until a 1 is written to OUT2VU (in reg 54 or 55) Analogue Outputs 7 LOUT2ZC 0 Speaker volume zero cross enable: 1 = Change gain on zero cross only 0 = Change gain immediately Analogue Outputs 6 LOUT2MUTE 0 Left speaker output mute: 0 = Normal operation 1 = Mute Analogue Outputs 5:0 LOUT2VOL 111001 Left speaker output volume: 000000 = -57dB ... 111001 = 0dB ... 111111 = +6dB Analogue Outputs 8 OUT2VU N/A LOUT2 and ROUT2 volumes do not update until a 1 is written to OUT2VU (in reg 54 or 55) Analogue Outputs 7 ROUT2ZC 0 Speaker volume zero cross enable: 1 = Change gain on zero cross only 0 = Change gain immediately Analogue Outputs 6 ROUT2MUTE 0 Right speaker output mute: 0 = Normal operation 1 = Mute Analogue Outputs 5:0 ROUT2VOL 111001 Right speaker output volume: 000000 = -57dB ... 111001 = 0dB ... 111111 = +6dB Analogue Outputs 00 Reserved 0 0 = Output stage outputs OUT3 mixer 1 = Output stage muted - drives out VMID. Can be used as VMID buffer in this mode. (Not to be used for Capless HP pseudo GND) 00 Reserved 8:7 6 OUT3MUTE 5:4 w Analogue Outputs PD, Rev 4.1, June 2009 78 WM8986 Production Data REGISTER ADDRESS 57 (39h) 61 (3Dh) BIT LABEL DEFAULT DESCRIPTION REFER TO 3 OUT4_2OUT3 0 OUT4 mixer output to OUT3 0 = disabled 1= enabled Analogue Outputs 2 BYPL2OUT3 0 Left PGA output to OUT3 0 = disabled 1= enabled Analogue Outputs 1 LMIX2OUT3 0 Left DAC mixer to OUT3 0 = disabled 1= enabled Analogue Outputs 0 LDAC2OUT3 1 Left DAC output to OUT3 0 = disabled 1= enabled Analogue Outputs 8 0 Reserved 7 OUT3_2OUT4 0 OUT3 mixer output to OUT4 0 = disabled 1 = enabled Analogue Outputs 6 OUT4MUTE 0 0 = Output stage outputs OUT4 mixer 1 = Output stage muted - drives out VMID. Can be used as VMID buffer in this mode. (Not to be used for Capless HP pseudo GND) Analogue Outputs 5 HALFSIG 0 0=OUT4 normal output 1=OUT4 attenuated by 6dB Analogue Outputs 4 LMIX2OUT4 0 Left DAC mixer to OUT4 0 = disabled 1= enabled Analogue Outputs 3 LDAC2OUT4 0 Left DAC to OUT4 0 = disabled 1= enabled Analogue Outputs 2 BYPR2OUT4 0 Right PGA output to OUT4 0 = disabled 1= enabled Analogue Outputs 1 RMIX2OUT4 0 Right DAC mixer to OUT4 0 = disabled 1= enabled Analogue Outputs 0 RDAC2OUT4 1 Right DAC output to OUT4 0 = disabled 1= enabled Analogue Outputs 8 0 Global bias control 0 = normal 1 = 0.5x Bias Control 7:0 0000000 Reserved w PD, Rev 4.1, June 2009 79 WM8986 Production Data DAC DIGITAL FILTER CHARACTERISTICS PARAMETER Passband TEST CONDITIONS MIN +/- 0.035dB 0 -6dB TYP +/-0.035 Stopband UNIT 0.5fs Passband Ripple Stopband Attenuation MAX 0.454fs dB 0.546fs f > 0.546fs Group Delay -55 dB 29/fs Table 43 DAC Digital Filter Characteristics TERMINOLOGY 1. Stop Band Attenuation (dB) - the degree to which the frequency spectrum is attenuated (outside audio band) 2. Pass-band Ripple - any variation of the frequency response in the pass-band region w PD, Rev 4.1, June 2009 80 WM8986 Production Data DAC FILTER RESPONSES 3.05 0 3 -20 2.95 -40 2.9 Response (dB) Response (dB) 20 -60 -80 -100 2.85 2.8 2.75 -120 2.7 -140 2.65 2.6 -160 0 0.5 1 1.5 2 0 2.5 0.05 0.1 0.15 Figure 36 DAC Digital Filter Frequency Response (128xOSR) 0.25 0.3 0.35 0.4 0.45 0.5 0.45 0.5 Figure 37 DAC Digital Filter Ripple (128xOSR) 3.05 20 0 3 -20 2.95 -40 2.9 Response (dB) Response (dB) 0.2 Frequency (fs) Frequency (fs) -60 -80 -100 2.85 2.8 2.75 -120 2.7 -140 2.65 2.6 -160 0 0.5 1 1.5 2 2.5 Frequency (fs) Figure 38 DAC Digital Filter Frequency Response (64xOSR) w 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 Frequency (fs) Figure 39 DAC Digital Filter Ripple (64xOSR) PD, Rev 4.1, June 2009 81 WM8986 Production Data 5-BAND EQUALISER 15 15 10 10 5 5 Magnitude (dB) Magnitude (dB) The WM8986 has a 5-band equaliser which can be applied to either the ADC path or the DAC path. The plots from Figure 40 to Figure 53 show the frequency responses of each filter with a sampling frequency of 48kHz, firstly showing the different cut-off/centre frequencies with a gain of 12dB, and secondly a sweep of the gain from -12dB to +12dB for the lowest cut-off/centre frequency of each filter. 0 -5 -5 -10 -10 -15 -1 10 10 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 -15 -1 10 5 Figure 40 EQ Band 1 Low Frequency Shelf Filter Cut-offs 15 15 10 10 5 5 0 -5 -10 -10 10 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 5 Figure 42 EQ Band 2 - Peak Filter Centre Frequencies, EQ2BW=0 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 5 0 -5 -15 -1 10 10 Figure 41 EQ Band 1 Gains for Lowest Cut-off Frequency Magnitude (dB) Magnitude (dB) 0 -15 -1 10 Figure 43 10 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 5 EQ Band 2 - Peak Filter Gains for Lowest Cut-off Frequency, EQ2BW=0 15 10 Magnitude (dB) 5 0 -5 -10 -15 -2 10 10 -1 10 0 1 10 Frequency (Hz) 10 2 10 3 10 4 Figure 44 EQ Band 2 - EQ2BW=0, EQ2BW=1 w PD, Rev 4.1, June 2009 82 WM8986 15 15 10 10 5 5 Magnitude (dB) Magnitude (dB) Production Data 0 0 -5 -5 -10 -10 -15 -1 10 10 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 5 -15 -1 10 Figure 45 EQ Band 3 - Peak Filter Centre Frequencies, EQ3BFigure 46 10 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 5 EQ Band 3 - Peak Filter Gains for Lowest Cut-off Frequency, EQ3BW=0 15 10 Magnitude (dB) 5 0 -5 -10 -15 -2 10 10 -1 10 0 1 10 Frequency (Hz) 10 2 10 3 10 4 Figure 47 EQ Band 3 - EQ3BW=0, EQ3BW=1 w PD, Rev 4.1, June 2009 83 Production Data 15 15 10 10 5 5 Magnitude (dB) Magnitude (dB) WM8986 0 0 -5 -5 -10 -10 -15 -1 10 10 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 -15 -1 10 5 Figure 48 EQ Band 4 - Peak Filter Centre Frequencies, EQ3BFigure 49 10 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 5 EQ Band 4 - Peak Filter Gains for Lowest Cut-off Frequency, EQ4BW=0 15 10 Magnitude (dB) 5 0 -5 -10 -15 -2 10 10 -1 10 0 1 10 Frequency (Hz) 10 2 10 3 10 4 15 15 10 10 5 5 Magnitude (dB) Magnitude (dB) Figure 50 EQ Band 4 - EQ3BW=0, EQ3BW=1 0 0 -5 -5 -10 -10 -15 -1 10 10 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 5 Figure 51 EQ Band 5 High Frequency Shelf Filter Cut-offs w -15 -1 10 10 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 5 Figure 52 EQ Band 5 Gains for Lowest Cut-off Frequency PD, Rev 4.1, June 2009 84 WM8986 Production Data Figure 53 shows the result of having the gain set on more than one channel simultaneously. The blue traces show each band (lowest cut-off/centre frequency) with 12dB gain. The red traces show the cumulative effect of all bands with +12dB gain and all bands -12dB gain, with EqxBW=0 for the peak filters. 20 15 Magnitude (dB) 10 5 0 -5 -10 -15 -1 10 10 0 10 1 2 10 Frequency (Hz) 10 3 10 4 10 5 Figure 53 Cumulative Frequency Boost/Cut w PD, Rev 4.1, June 2009 85 WM8986 Production Data APPLICATIONS INFORMATION RECOMMENDED EXTERNAL COMPONENTS Figure 54 External Component Diagram Notes: 1. When operating LOUT2 and ROUT2 in class D mode, it is recommended that LC filtering is placed as close to the LOUT2 and ROUT2 pins as possible. Low ESR components should be used for maximum efficiency. It is recommended that a filter, consisting of a 33H inductor and a 220nF capacitor, is used for optimal performance. 2. The addition of ferrite beads to the outputs of LOUT2 and ROUT2 will suppress any potential interference noise produced by the class D switching clocks. w PD, Rev 4.1, June 2009 86 WM8986 Production Data PACKAGE DIAGRAM FL: 28 PIN COL QFN PLASTIC PACKAGE 4 X 4 X 0.75 mm BODY, 0.45 mm LEAD PITCH DM043.G DETAIL 1 D 28 22 21 1 INDEX AREA (D/2 X E/2) 4 A E SEE DETAIL 2 15 7 2X 8 14 1 bbb M C A B b e 2X aaa C aaa C TOP VIEW BOTTOM VIEW DETAIL 1 A 0.08 C A1 SIDE VIEW C 5 PIN 1 IDENTIFICATION 0.150MM SQUARE L Datum L1 0.275MM DETAIL 2 SEATING PLANE DETAIL 2 0.275MM 1 ccc C A3 Terminal Tip e/2 e R W T A3 G H b Exposed lead DETAIL 2 Dimensions (mm) Symbols A A1 A3 b D E e G H L L1 T W MIN 0.725 0 0.18 3.95 3.95 NOM 0.75 0.02 0.203 REF MAX 0.775 0.05 NOTE 0.23 4.00 4.00 0.45 BSC 0.535 REF 0.100 REF 0.40 REF 0.05 REF 0.100 REF 0.230 REF 0.28 4.05 4.05 1 5 Tolerances of Form and Position aaa bbb ccc 0.15 0.10 0.10 NOTES: 1. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.15 mm AND 0.30 mm FROM TERMINAL TIP. 2. ALL DIMENSIONS ARE IN MILLIMETRES. 3. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS. 4. REFER TO APPLICATIONS NOTE WAN_0118 FOR FURTHER INFORMATION REGARDING PCB FOOTPRINTS AND QFN PACKAGE SOLDERING. 5. DEPENDING ON THE METHOD OF LEAD TERMINATION AT THE EDGE OF THE PACKAGE, PULL BACK (L1) MAY BE PRESENT. 6. THIS DRAWING IS SUBJECT TO CHANGE WITHOUT NOTICE. w PD, Rev 4.1, June 2009 87 WM8986 Production Data IMPORTANT NOTICE Wolfson Microelectronics plc ("Wolfson") products and services are sold subject to Wolfson's terms and conditions of sale, delivery and payment supplied at the time of order acknowledgement. Wolfson warrants performance of its products to the specifications in effect at the date of shipment. Wolfson reserves the right to make changes to its products and specifications or to discontinue any product or service without notice. Customers should therefore obtain the latest version of relevant information from Wolfson to verify that the information is current. Testing and other quality control techniques are utilised to the extent Wolfson deems necessary to support its warranty. Specific testing of all parameters of each device is not necessarily performed unless required by law or regulation. In order to minimise risks associated with customer applications, the customer must use adequate design and operating safeguards to minimise inherent or procedural hazards. Wolfson is not liable for applications assistance or customer product design. The customer is solely responsible for its selection and use of Wolfson products. Wolfson is not liable for such selection or use nor for use of any circuitry other than circuitry entirely embodied in a Wolfson product. Wolfson's products are not intended for use in life support systems, appliances, nuclear systems or systems where malfunction can reasonably be expected to result in personal injury, death or severe property or environmental damage. Any use of products by the customer for such purposes is at the customer's own risk. Wolfson does not grant any licence (express or implied) under any patent right, copyright, mask work right or other intellectual property right of Wolfson covering or relating to any combination, machine, or process in which its products or services might be or are used. Any provision or publication of any third party's products or services does not constitute Wolfson's approval, licence, warranty or endorsement thereof. Any third party trade marks contained in this document belong to the respective third party owner. Reproduction of information from Wolfson datasheets is permissible only if reproduction is without alteration and is accompanied by all associated copyright, proprietary and other notices (including this notice) and conditions. Wolfson is not liable for any unauthorised alteration of such information or for any reliance placed thereon. Any representations made, warranties given, and/or liabilities accepted by any person which differ from those contained in this datasheet or in Wolfson's standard terms and conditions of sale, delivery and payment are made, given and/or accepted at that person's own risk. Wolfson is not liable for any such representations, warranties or liabilities or for any reliance placed thereon by any person. ADDRESS: Wolfson Microelectronics plc Westfield House 26 Westfield Road Edinburgh EH11 2QB United Kingdom Tel :: +44 (0)131 272 7000 Fax :: +44 (0)131 272 7001 Email :: sales@wolfsonmicro.com w PD, Rev 4.1, June 2009 88