M7E-WH0511A - OMRON - Product.Network

CSM_M7E(80_120_200mm)_DS_E_10_3

Digital Display (80/120/200 mm)

M7E

Digital Display with Wire-saving Serial

Transmission Function (B7A Output)

• Single-color (red or green) and three-color (red, green, or

orange selectable) displays with a character height of 80, 120,

or 200 mm are available for a variety of applications and

locations.

• Thin design with a 39.5-mm depth for the 120-mm model is

perfect for saving space in equipment and devices.

• Decimal display including negative sign (−) display with signal

codes is possible.

Ordering Information

■List of Models

Models with 80 mm-high Characters

Models with 120 mm-high Characters

Models with 200 mm-high Characters

Display contents Type Logic input Display color Model

Decimal Front

mounting

Negative Red M7E-08DRN2

Green M7E-08DGN2

Hexadecimal Front

mounting

Red M7E-08HRN2

Green M7E-08HGN2

Display contents Type Logic input Display color Model

Decimal Rear

mounting

Negative Red M7E-12DRN1

Green M7E-12DGN1

Red/green/orange M7E-12DKN1

Front

mounting

Red M7E-12DRN2

Green M7E-12DGN2

Red/green/orange M7E-12DKN2

Hexadecimal Rear

mounting

Red M7E-12HRN1

Green M7E-12HGN1

Red/green/orange M7E-12HKN1

Front

mounting

Red M7E-12HRN2

Green M7E-12HGN2

Red/green/orange M7E-12HKN2

Display contents Type Logic input Display color Model

Decimal Rear

mounting

Negative Red M7E-20DRN1

Green M7E-20DGN1

Red/green/orange M7E-20DKN1

Hexadecimal Rear

mounting

Red M7E-20HRN1

Green M7E-20HGN1

Red/green/orange M7E-20HKN1

Specifications

■Ratings

■Characteristics

Note: 1. Initial values

2. Impulse conditions:

Rise time: 1 ns +10% max.

Pulse width: 100 ns, 1 μs

Polarity: Positive, negative, asynchronous to power

frequency, 100 Hz repeat frequency.

Rated power supply 24 VDC

Allowable voltage

fluctuation range

90% to 110% of rated voltage

Current consumption

(per display)

M7E-08 (at 24 VDC)

Red LED: 120 mA max.

Green LED: 160 mA max.

M7E-12 (at 24 VDC)

Red LED: 200 mA max.

Green LED: 330 mA max.

Red/Green LED (orange: lit): 330 mA max.

M7E-20 (at 24 VDC)

Red LED: 420 mA max.

Green LED: 500 mA max.

Red/Green LED (orange: lit): 500 mA max.

Input

level

Nega-

tive

logic

Stan-

dard

High: 4 V to power supply voltage

Low: 0 to 1.5 V

Ambient temperature Operating: −10 to 55°C (with no icing)

Storage: −25 to 70°C (with no icing)

Ambient humidity Operating: 35% to 85% (with no

condensation)

Insulation

resistance

100 MΩ min. (at 500 VDC) between each

terminal and mounting panel

Dielectric

strength

500 VAC, 50/60 Hz for 1 min between each

terminal and mounting panel

Noise immunity

(See note.)

Power terminal: ±500 V

Input terminals: ±500 V (normal mode)

±1,500 V (common mode)

Vibration

resistance

Destruction: 10 to 55 Hz, 0.75-mm double

amplitude

Shock resistance Destruction: 300 m/s2

Degree of

protection

IEC IP40 (portion on panel surface)

Connectable PLCs

M7E model PLC's output method

Display Logic

input

Static output

PNP output NPN output

Decimal Negative Not connectable Connectable

Hexadecimal Negative Not connectable Connectable

■Accessories (Order Separately)

Harness Connector

Dimensions Model

70 mm M7E-WH0111A

500 mm M7E-WH0511A

1,000 mm M7E-WH1011A

M7E

Installation

■Cables

Refer to M7E Options for information on using cables

(OMRON XW2Z-R@C, XW2Z-RY@C, and XW2Z-RO-@C-@).

■M7E-WH@11A

Harness Connector

■Input Codes

Negative Logic Standard Unit

* Either low or high. All inputs are pulled up internally. Therefore high can be open.

Note: 1. Only the numeral will be OFF. (There is no relationship to the decimal point.)

2. Only the numeral will be OFF if there is parallel input with CN1. The decimal point will be lit if there is B7A serial input with TB1.

3. Only the numeral will be OFF if there is parallel input with CN1. The decimal point will be OFF if there is B7A serial input with TB1.

4. The previous statuses of A to D before LE goes low will be held. There is no relationship to the decimal point. The LE latch function will not, however, operate

at the time of serial transmission.

CN3 CN2

Japan Solderless

Terminal EHR-11

lModel

70 mm M7E-WH0111A

500 mm M7E-WH0511A

1,000 mm M7E-WH1011A

Input signal Output display condition

Connector pin No. (CN1) ANMLKEF

Terminal symbol LE D C B A DP BI RBI RBO Decimal Hexadecimal

Input signals HHHHHHHL LBlank Blank

HHHHHHHHH 00

HHHHHLH * H 0. 0.

HHHHLHH * H 11

HHHLHHH * H 22

HHHL LHH * H 33

HHLHHHH * H 44

HHLHLHH * H 55

HHL LHHH * H 66

HHLLLHH*H 77

HLHHHHH * H 88

HLHHLHH*H 99

HLHLHHH*H a

H L H L L H H * H Blank (See note 1.) b

H L L H H H H * H DP lights at serial input.

(See note 2.)

H L L H L H H * H DP lights at serial input.

(See note 3.)

H L L L H H H * H Blank (See note 1.) e

H L L L L H H * H Blank (See note 1.) f

*****LH*H

* * * * * * L * H Blank (See note 1.) Blank (See note 1.)

L * * * * * H * H (See note 4.) (See note 4.)

M7E

■Terminal Arrangement/Functions

1. Input Terminal

TB1

CN1 (Connector: XG4C-2031 for 80-mm Models,

XG4A-2034 for 120-mm/200-mm Models)

Note: If the R and G of the multi-color display are set low, the Unit will display in orange.

Terminal symbol Name Function

+V Power supply Positive (+) power-supply terminal.

GND Power supply 0 V power-supply terminal.

SI Serial data input B7A serial data received

Terminal

No.

XG4-

2034 pin

No.

Terminal

symbol

Name Function

1(20)LE1 Control input 1st-digit latch input: The previous display is held when this signal is input.

2(18)LE2 Control input 2nd-digit latch input: The previous display is held when this signal is input.

3(16)LE3 Control input 3rd-digit latch input: The previous display is held when this signal is input.

4(14)LE4 Control input 4th-digit latch input: The previous display is held when this signal is input.

5(12)DP Data input The decimal point lights. Operates independently of the LE signal.

6(10)BI Control input Blank input: Turns OFF all the displays.

7(8)R Control input Color selector input: Red is lit when low is input (See note.)

8(6)G Control input Color selector input: Green is lit when low is input (See note.)

9(4)GND Power supply 0 V power-supply terminal. (Terminals 9 and 19 are connected internally.)

10 (2) +V Power supply Positive side (+) power-supply terminal. (Terminals 10 and 20 are connected

internally.)

11 (19) A Data input A (20)

The value and symbol corresponding to the input code

signal are displayed. Refer to the list of input codes for the

contents of display.

12 (17) B Data input B (21)

13 (15) C Data input C (22)

14 (13) D Data input D (23)

15 (11) NC Open ---

16 (9) NC Open ---

17 (7) NC Open ---

18 (5) NC Open ---

19 (3) GND Power supply 0 V power-supply terminal. (Terminals 9 and 19 are connected internally.)

20 (1) +V Power supply Positive side (+) power-supply terminal. (Terminals 10 and 20 are connected

internally.)

Supply voltage: 24 VDC

Terminal Arrangement

Models with 120/200-mm-high

Characters

M7E

2. Multi-digit Connection Terminals

CN2, CN3

Note: 1.

The CN2 or CN3 Multi-digit Connector must be used for serial

transmission and dynamic control with the B7A Link Terminal.

Refer to page 5 for details. To use zero suppression, refer to

page 8. Use the CN2 and CN3 for connection with the M7E only.

2. Use the following connectors for the connector terminals:

CN1: XG4M-2030 or equivalent

CN2 and CN3: M7E-WH@11A

Refer to CN1 Terminal Arrangement for the pin numbers.

Refer to page 2 for the dedicated harness.

3. Refer to the list of input codes for RBO or RBI control.

CN1 Terminal Arrangement

Note: 1. The numbers in parentheses are the pin numbers for the

XG4C-2031 Connector for Models with 80-mm-high

Characters and for the XG4A-2034 Connector for Models

with 120/200-mm-high Characters.

2. Connectors

•Flat-cable Connector: XG4M-2030

•Connectors for Loose Wires with Crimp Terminals:

XG5M-2032-N (Applicable wire gauge: AWG24)

XG5M-2035-N (Applicable wire gauge: AWG28 to AWG26)

Models with 80 mm-high Characters

■Block Diagram

Note: Circled numbers are the connector pin numbers. Signal Input Circuit

Negative Logic Model

Terminal

No.

CN2 (IN) CN3 (OUT)

Symbol Name Function Symbol Name Function

1A Data

input A (20)A Data

output A (20)

2B Data

input B (21)B Data

output B (21)

3C Data

input C (22)C Data

output C (22)

4D Data

input D (23)D Data

output D (23)

5+V Power

supply

Positive side

(+) power-

supply terminal

+V Power

supply

Positive side

(+) power-

supply terminal

6GND Power

supply

0 V power-

supply terminal

GND Power

supply

0 V power-

supply terminal

7SI Control

input

B7A serial data

received

SO Control

output

B7A serial data

transmitted

8RBO Control

output

Zero-suppress

output

(See note 3.)

RBI Control

input

Zero-suppress

input

(See note 3.)

9LEI1 Control

input

1st-digit latch

input

LEO1 Control

output

2nd-digit latch

output

10 LEI2 Control

input

2nd-digit latch

input

LEO2 Control

output

3rd-digit latch

output

11 LEI3 Control

input

3rd-digit latch

input

LEO3 Control

output

4th-digit latch

output

(19)(17) (1)

(20)(18) (2)

11 12 13 14 15 16 17 1819 20

12345678910

PCB

View of Mating Portion

CN1

+24 V

GND

RBO

LEI1

LEI2

LEI3

+24 V

GND

RBI

LEO1

LEO2

LEO3

DSWCN3CN2

TB1

+24 VGNDSI

PCB

Case

Input connector

Power

supply circuit

Input circuit

Driver

LED elements

Multi-digit

connector from

the rightmost digit

Multi-digit

connector to the

leftmost digit

Operation Examples of Zero Suppression

Zero suppression operates when the display is 0, RBI is low, and the decimal

point is not lit. Then low is output to RBO.

Example 1: Zero suppression is not required and the RBI input and RBO

output of each digit are open.

Example 2: Zeros are suppressed only for the digits on the left of the digit

where the decimal is lit when both zero suppression and a

decimal point are being used.

Note: Use RBO output for the connection with RBI input only.

Signal input

3.9 kΩ

4.3 kΩ

+5 V

Fourth digit Third digit Second digit First digit

Example 1

Example 2

M7E

■External Connections

Refer to Block Diagram on page 4 and Terminal Arrangement/Functions on page 3 for external connections for each Unit.

PLC Connections

Refer to your PLC operation manual before connecting the PLC.

OUTPUT UNIT

(BCD output)

Harness connector

M7E-WH@11A

PLC

A to D,

DP, BI

PLC

A to D,

DP, LE

Harness connector

M7E-WH@11A

Static Control

Connected to CS1W-OD261 and CJ1W-OD231 Transistor Output Unit

Connect the PLC's output to the A to D (BCD

output), DP, and BI terminals individually.

Note: Use separate output terminals for DP

or BI control.

Dynamic Control

Connected to C200H-OD215 (Static Mode) Transistor Output Unit

•Connect the PLC's output to the A to D (BCD

output) terminals of the rightmost digit.

•Latch control is set with the LE1 to LE4 terminals of

the rightmost Unit.

The terminals correspond as follows:

LE1: Rightmost digit (example: 1's digit)

LE2: Second digit (example: 10's digit)

LE3: Third digit (example: 100's digit)

LE4: Forth digit (example: 1,000's digit)

Note: 1. The display colors of the three-color displays must be selected individually.

2. In static mode, ladder programming is required for latch control.

3. If the cycle time of the PLC is too short, its relationship with the ON/OFF

response time of the M7E may not work well. Set a minimum cycle time or

otherwise adjust the cycle time accordingly.

4. The reception of orders for C200H-OD215 was discontinued at the end of

March 2017.The recommended replacements are the CS1W-OD231 and

CJ1W-OD231, but they not Dynamic Output Units. Therefore, ladder

programming will be required to use them as replacements.

B7A Link Terminal •By supplying power to a single display, all the displays will be

supplied with power.

•The B7A's serial output must be connected to the SI terminal of

the rightmost TB1.

•Use OMRON's M7E-WH@11A Harness Connectors or

equivalent to connect all Units.

•The DP and BI terminals can be controlled by transmitting the

following special data

Hexadecimal C data: Turns ON the decimal point of the relevant

digit.

Hexadecimal D data: Turns OFF the decimal point of the

relevant digit.

Hexadecimal F data: Deletes the display (BI control) of the

relevant digit.

•Use the B7A Link Terminal with a normal I/O delay of 19.2 ms.

The B7A with short I/O delay cannot be used.

Note: The display colors of the three-color displays must be selected individually.

Connected to CS1W-OD211 and CJ1W-OD211

Transistor Output Unit

M7E

■Serial Transmission with B7A Link Terminal

A series of models incorporating a communications (serial transmission) function is available.

By using the B7A Link Terminal (PLC connector model), the Units can be connected to the PLC with ease. The 16-point B7A Link Terminal allows

the control of a maximum of four digits over two wires.

Available Link Terminal Models

Transmission Path

Transmission distance:

A maximum transmission distance of 500 m is

possible by using the VCTF 0.75 x 2C Cable if

power is supplied independently to the Input and

Output Link Terminals.

A maximum transmission distance of 100 m is

possible by using the VCTF 0.75 x 3C Cable if a

single pow er supply is connected to the Input or

Output Link Terminal, in which case the current

flow on the power lines (positive and negative

lines) is 1.8 A maximum.

Transmission delay:

A maximum of 50 ms for data display after the

B7A's input signal becomes definite.

Minimum Input Time

Use an input time of 80 ms min. to the Input

Unit for the B7A.

Signal Allocation

B7A-M7E Corresponding Pin List

The B7A's switch terminals correspond to the

M7E's parallel input signals as follows:

Note: A maximum of two Display Units can be

connected when the 10-point B7A Link

Terminal is used and a maximum of four

Display Units can be connected when the

16-point B7A Link Terminal is used.

Errors

1. No signal transmission is available due to the

disconnection of the transmission path (the SI

or GND wire).

2. The waveform is greatly distorted due to

ex ternal noise interference or because the

transmission path is longer than the

permissible transmission path.

Error Indication

When an error results, “-” will be displayed and

the display will flash. After the condition returns to

normal, reception data will be displayed.

Display after Error

Correction

After the condition returns to normal, the display

will be reset automatically and reception data will

be displayed.

Transmission side Wiring No. of I/O points Connectable M7E

Display Units

B7A-T10S1 Screw terminal model 10 2 Note: 1. Use the B7A Link Terminal with a normal I/O delay of

19.2 ms. The B7A with short I/O delay cannot be used.

2. The connection of the 32-point connector model is as

follows:

3. For details on corresponding models, refer to each

applicable model’s catalog.

B7A-T10S3 Screw terminal model 10 2

B7A-T10M2 Module model 10 2

B7A-T6A1 Screw terminal model 16 4

B7A-T6B1 Screw terminal model 16 4

B7A-T6C1 Screw terminal model 16 4

B7A-T6D2 Module model 16 4

B7A-T6E3 Connector model 16 4

B7A-T3E3 (See note 2.) Connector model 32 8

C200H-B7A (See note 3.) Screw terminal model 16 × @ ports 4 × @ ports

CQM1-B7A (See note 3.) Screw terminal model 16 × @ ports 4 × @ ports

CJ1W-B7A (See note 3.) Screw terminal model 16 × @ ports 4 × @ ports

CS1W-B7A (See note 3.) Screw terminal model 16 × @ ports 4 × @ ports

M7E-08/12/20

Transmission distance: 500 m max.

24-VDC

power

supply DC power

supply

24-VDC

power

supply

Transmission distance: 100 m max.

(12 to 24 V)

B7A

(PLC connector model)

B7A

(PLC connector model)

PLC

Power Supplies Placed on Both the Transmitting and Receiving Sides

Power Supply Placed Only on the Receiving Side

Units can be

connected easily

with the dedicated

harness.

SIG1

SIG2

PLC

connector

model 32

points

B7A switch terminal M7E parallel input

First digit

(1's digit) A

Second dig i t

(10's digit) A

A10

A11

Third digit

(100's digit) A

A12

A13

A14

A15

Fourth digit

(1000's digit) A

M7E

■Serial Transmission Control Examples

1. 1234 is displayed.

Note: The transmission data is hexadecimal.

2. −123 is displayed.

3. 12.34 is displayed.

4. 9.876 is displayed.

5. 4.2-1 is displayed.

6. The displayed decimal point will be OFF.

7. Changing the numeral and decimal point simultaneously.

(It is, however, impossible to change the numeral and decimal

point on the same digit simultaneously.)

8. Turn OFF the display by sending data F.

Note: DP and BI control using serial transmission is not displayed in

hexadecimal.

■A Variety of Control Operations with Short-circuit Sockets

By removing the rear cover of the Display Unit and setting the XJ8A-0211 Short-circuit Socket, the following control operations are possible.

Transmission data

1234 →Display 1234

Transmission data

A123 →Display −123

Transmission data

DCDD →Display −1. 2 3 (The decimal point

is controlled first.)

Transmission data

1234 →Display 12.34(Numeral data is

transmitted next.)

Transmission data

CDDD →Display 12.34(The decimal point

is controlled first.)

Transmission data

9876 →Display 9. 8 7 6 (Numeral data is

transmitted next.)

Transmission data

42A1 →Display 4. 2 −1(Numeral setting

is possible.)

Transmission data

DDDD →Display 42−1

Transmission data

C311 →Display 4311

Transmission data

DDDD →Display 4314(The decimal

point is OFF.)

Transmission data

32F1 →Display 32 1

(Display turns OFF

with F transmission.)

ONOFF

OFF

RBI

TER

1. DP (J5)

2. RBI (J9)

TER (J11)

3. R (J8)

G (J10)

Short-circuit

socket

123456 SW1

RBI

TER

N.C

SEL1

SEL2

M7E

Leftmost digit

Short-circuited

Open

Short-circuited

Open

Short-circuited

Open

M7E

Rightmost digit

M7E-WH@11A

M7E

RBI (J9)

TER (J11)

M7E

Decimal Control

•Short-circuit the DP (J5) terminals with a short-circuit socket so that the decimal point will be

always lit.

•The short-circuit socket is short circuited at the factory (i.e., normally lit). Open the short-circuit

socket if external control or lighting are not required

Zero Suppression Control

•When the z ero suppre ssio n funct ion is not u se d, the RB I (J9 ) terminals mu st b e o pen. The TER

(J11) terminals can be either short-circuited or open.

•When zero suppre ssio n i s not used, the RBI (J9) terminals of the M7E Digital Display Unit for

the leftmost digit must be short-circuited, those of all the other M7E Digital Displa y Units m ust be

open, the TER (J11) terminals of the M7E Digital Display Unit for the rightmost digit must be

open, and those of all the other M7E Digital Display Units must be shor t-circuited.

Example of Zero Supp r ession Setting for Four Digits on the M7E (120/

200-mm Model)

Note: To use zero suppression, CN2 and CN3 must be connected with an M7E-

WH@11A Harness Connector.

In static mode, ladder programming is required for latch control. If latch control

is not used, cut the data I/O lines (pins 1 to 4) on the Harness Connector.

Display Color Contr ol (Three-color Model Only)

•Short-circuit the R (J8) terminals with a short-circuit socket so that the display will be lit in red.

•Short-circuit the G (J10) terminals with a short-circuit socket so that the display will be lit in

green.

•Short-circuit the R (J8) as well as G (J10) terminals with two short-circuit so ckets so that the

display will be lit in orange.

Note: When the R (J8) as well as G (J10) terminals are open, the display will be OFF if the CN1

Input Connector has not been connected yet.

Note: 1. All the terminals are short-circuited before shipping. Short-circuit or open the terminals according

to the application.

2. Single-color (red or green) models do not incorporate the R (J8) and G (J10) terminals.

3. These terminals must be open when controlling the DP (J5), R (J8), and G (J10) terminals

externally by inputting signals from the CN1. (The short-circuit socket will take precedence.)

4. All the terminals J5 to J11 are connected to GND.

5. The 80-mm Model uses DIP switches. ON: Short-circuited OFF: Open

(SEL1 and SEL2 are switches to adjust brightness.)

80-mm Model

DIP Switch

•Pins 1 to 4 are all factory-set

to OFF.

•Pins 5 and 6 are factory-set

for brightness adjustment. Do

not change the setting of

these pins; the brightness will

change.

Example of Zero Suppr ession Setting for Four Digits on the M7E (80-

mm Model)

M7E

■Zero Suppression

To use zero suppression, first connect the CN3 and CN2 connectors on the M7E to the M7E-WH@11A Harness Connector.

Then, set the DIP s witch on the M7E-08@ (80-mm model) or short the required pins with short-circuit sockets on the M7E-12@ (80-mm model) or

M7E-20@(200-mm model).

Zero Suppression for 80-mm Models

To use zero suppression, turn ON the RBI and TER pins on the DIP

switch on the M7E for the most-significant digit, turn OFF the RBI

and TER pins on the DIP switch on the M7E for the least-significant

digit, and then turn the RBI pin OFF and the TER pin ON on the DIP

switches on the M7E for the other digits.

To use zero suppression, CN2 and CN3 must be connected with the

M7E-WH@11A Harness Connector.

In static mode, ladder programming is required for latch control. If latch

control is not used, cut the data I/O lines (pins 1 to 4) on the Harness

Connector.

Example of Zero Suppression Setting for Four Digits on

the M7E (80-mm Model)

Zero Suppression for 120/200-mm Models

To use zero suppression, short-circuit the RBI and TER pins with the

short-circuit sockets on the M7E for the most-significant digit, and

leave these pins open on the M7E for the least-significant digit. For

the M7E for other digits, leave the RBI pin open and short-circuit the

TER pin.

By removing the rear cover of the Display Unit and setting the XJ8A-

0211 Short-circuit Socket, the following control operations are

possible.

To use zero suppression, CN2 and CN3 must be connected with the

M7E-WH@11A Harness Connector.

In static mode, ladder programming is required for latch control. If latch

control is not used, cut the data I/O lines (pins 1 to 4) on the Harness

Connector.

Note: 1. All the terminals are short-circuited before shipping. Short-

circuit or open the terminals according to the application.

2. Single-color (red or green) models do not incorporate the R

(J8) and G (J10) terminals.

3. These terminals must be open when controlling the DP (J5),

R (J8), and G (J10) terminals externally by inputting signals

from the CN1. (The short-circuit socket will take

precedence.)

4. All the terminals J5 to J11 are connected to GND.

123456 SW1

RBI

TER

N.C

SEL1

SEL2

DIP Switch

•

Pins 1 to 4 are all factory-set to OFF.

•Pins 5 and 6 are factory-set for

brightness adjustment. Do not

change the setting of these pins;

the brightness will change.

OFF

ON/OFF OFF

ON/OFF

RBI

TER

ONOFF

OFF

RBI

TER

M7E-WH@11A

M7E M7E

ONOFF

OFF

RBI

TER Turn ON pin 1 on the DIP switch

to light the decimal point.

OFF

ON/OFF OFF

ON/OFF ON

ON/OFF

RBI

TER

M7E

Leftmost digit

M7E

Rightmost digit

M7E-WH@11A

M7E M7E

M7E

Leftmost digit

M7E

Rightmost digit

M7E-WH@11A

M7E M7E

M7E

Leftmost digit

M7E

Rightmost digit

Short-circuit

socket

- - - - - - -1. DP (J5) Decimal Control

•Short-circuit the DP (J5) terminals with a short-

circuit socket so that the decimal point will be

always lit.

•The short-circuit socket is short circuited at the

factory (i.e., normally lit). Open the short-circuit

sock et if e x ternal control or light ing are n ot required

- - - -2. RBI (J9)

TER (J11) Zero Suppression Control

•

When the zero suppression function is not used, the

RBI (J9) terminals must be open. The TER (J11)

terminals can be either short-circuited or ope n.

•

When zero suppression is not used, the RBI (J9)

terminals of the M7E Digital Display Unit f or the leftmost

digit must be short-circuited, those of all the other M7E

Digital Display Units must be open, the TER (J11)

terminals of the M7E Digital Display Unit f or the

rightmost digit must be open, and those of all the other

M7E Digital Disp lay Units must be short-circuited.

M7E

Example of Zero Suppression Setting for Four Digits on

the M7E (120/200-mm Model)

RBI

TER

RBI

TER

M7E-WH@11A

M7E M7E

Open

Short-circuited

Open

Short-circuited

RBI

TER Turn ON pin 1 on the DIP switch

to light the decimal point.

Short-circuited

Open/Short-circuited

Open

Open/Short-circuited

Open

Open/Short-circuited

Open

Open/Short-circuited

RBI

TER

M7E

Leftmost digit

M7E

Rightmost digit

M7E-WH@11A

M7E M7E

M7E

Leftmost digit

M7E

Rightmost digit

M7E-WH@11A

M7E M7E

M7E

Leftmost digit

M7E

Rightmost digit

Open

Open/Short-circuited

Open

Open/Short-circuited

Open

Open/Short-circuited

Open

Open/Short-circuited

Open

Short-circuited

Open

Short-circuited

M7E

Operation

■Operation Timing (Input Signal Timing)

■Operation Chart

The following example shows the relationship between each input terminal and the display condition.

Data latch

Data input

signals A to D

Latching

input LE

tw: Pulse duration

th: Hold time

ts: Setup time

Data latchData read

Pulse duration (tw) 1.5 ms

Hold time (th) 0.75 ms

Setup time (ts) 2. 2 5 m s

Negative Logic

Data

Terminal

displayed

value

0123456789 Description

Input

signals A

(20)H

Inputs the data signal

as BCD (or binary

code).

(21)H

(22)H

(23)H

DP H

Low when the decimal

point lights. The

decimal point can light

without regard to the LE

signal.

BI H

Low when the display is

turned OFF.

LE H

Low when the display is

to be retained. (High is

retained until the signal

goes low.)

Display

condition ---

Remarks ---

(No display)

The “1” display is retained by

the LE signal. The “5” display is retained

by the LE signal. The display turned OFF by

the BI signal (no display).

M7E

Dimensions

Note: All units are in millimeters unless otherwise indicated.

Note: Tolerance is ±0.4 mm unless otherwise specified.

72.4

113 108.6

25.7

29.3

109.6±0.2

7°

M7E-08@@N2 Number

of Units Dimension

73.1±0.4

149.3±0.4

225.5±0.4

301.7±0.4

377.9±0.4

454.1±0.4

530.3±0.4

606.5±0.4

Panel Cutout

(Panel thickness: 1 to 4 mm)

LED

114

42.5

165.6

170

110.4

166.6±0.2

120

7°

M7E-12@@N2 Number

of Units Dimension

111.1±0.4

225.3±0.4

339.5±0.4

453.7±0.4

567.9±0.4

682.1±0.4

796.3±0.4

910.5±0.4

LED

Panel Cutout

(Panel thickness: 1 to 4 mm)

160.8164180195

16.7 25.5

105.6

42.2

180±0.2 165±0.2

5 dia. (max.)

106±0.2

58±0.2 A

120

7°

M7E-12@@N1

Number

of Units Dimension

106.6±0.4

212.6±0.4

318.6±0.4

424.6±0.4

530.6±0.4

636.6±0.4

742.6±0.4

848.6±0.4

Panel Cutout LED

243

19.6 22.4

42.2

266.2281296

120

176

281±0.2 267.2±0.2

5 dia. (max.)

120±0.2

176.4±0.2

200

7°

116

M7E-20@@N1

Number

of Units Dimension

177±0.4

353.4±0.4

529.8±0.4

706.2±0.4

882.6±0.4

1,059±0.4

1,235.4±0.4

1,411.8±0.4

Panel Cutout LED

M7E

Safety Precautions

■Precautions for Correct Use

Environment

•Use the switches in locations that are not subject to organic

solvents (thinner , benz ene, etc.), strong alkali, strong acid, sunlight,

corrosive gases, water, and oil.

•Use the units in areas not subject to vibration or shoc k in excess of

specifications.

Wiring

•When wiring with terminals or a connector, remove the rear cover

of the M7E and connect the M7E to the terminals or connector

properly, and be sure not to leave any wire cuttings inside the

Display Unit.

•Make sure that no wire is more than five meters long when wiring

the B7A link terminal.

Mounting

When mounting Display Units to a box, make slits on the rear part

and the top of the box for ventilation. If there is no proper ventilation,

the life of each Display Unit may be shortened.

Connecting Cable

When connecting an XG4M-2030 or XG4M-2030-T G79 Cable to a

Digital Display with 80-mm-high Characters, an XG4Z-0002 Lock

Lever can be used.

In the interest of product improvement, specifications are subject to change without notice.

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.

Terms and Conditions Agreement

Read and understand this catalog.

Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you

have any questions or comments.

Warranties.

(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship

for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron

disclaims all other warranties, express or implied.

(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT

NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER

ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE

PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.

Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the

Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at

Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or

replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount

equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,

repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products

were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate

modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall

not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or

electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,

recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above

warranty.

See http://www.omron.com/global/ or contact your Omron representative for published information.

Limitation on Liability; Etc.

OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,

LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,

WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.

Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.

Suitability of Use.

Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the

combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable

third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself

is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,

system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product

with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE

QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,

AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE

OVERALL EQUIPMENT OR SYSTEM.

Programmable Products.

Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence

thereof.

Performance Data.

Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining

suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate

it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.

Change in Specifications.

Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our

practice to change part numbers when published ratings or features are changed, or when significant construction changes are

made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers

may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at

any time to confirm actual specifications of purchased Product.

Errors and Omissions.

Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is

assumed for clerical, typographical or proofreading errors or omissions.

2017.4

In the interest of product improvement, specifications are subject to change without notice.

OMRON Corporation

Industrial Automation Company

http://www.ia.omron.com/