ADC10080CIMTX/NOPB - NATIONAL SEMICONDUCTOR

ADC10080

ADC10080 10-Bit, 80 MSPS, 3V, 78.6 mW A/D Converter

Literature Number: SNAS177G

February 1, 2008

ADC10080

10-Bit, 80 MSPS, 3V, 78.6 mW A/D Converter

General Description

The ADC10080 is a monolithic CMOS analog-to-digital con-

verter capable of converting analog input signals into 10-bit

digital words at 80 Megasamples per second (MSPS). This

converter uses a differential, pipeline architecture with digital

error correction and an on-chip sample-and-hold circuit to

provide a complete conversion solution and to minimize pow-

er consumption, while providing excellent dynamic perfor-

mance. A unique sample-and-hold stage yields a full-power

bandwidth of 400 MHz. Operating on a single 3.0V power

supply, this device consumes just 78.6 mW at 80 MSPS, in-

cluding the reference current. The Standby feature reduces

power consumption to just 15 mW.

The differential inputs provide a full scale selectable input

swing of 2.0 VP-P, 1.5 VP-P, 1.0 VP-P, with the possibility of a

single-ended input. Full use of the differential input is recom-

mended for optimum performance. An internal +1.2V preci-

sion bandgap reference is used to set the ADC full-scale

range, and also allows the user to supply a buffered refer-

enced voltage for those applications requiring increased ac-

curacy. The output data format is user choice of offset binary

or two’s complement.

This device is available in the 28-lead TSSOP package and

will operate over the industrial temperature range of −40°C to

+85°C.

Features

■Single +3.0V operation

■Selectable full-scale input swing

■400 MHz −3 dB input bandwidth

■Low power consumption

■Standby mode

■On-chip reference and sample-and-hold amplifier

■Offset binary or two’s complement data format

■Separate adjustable output driver supply

Key Specifications

■Resolution 10 Bits

■Conversion Rate 80 MSPS

■Full Power Bandwidth 400 MHz

■DNL ±0.25 LSB (typ)

■SNR (fIN = 10 MHz) 59.5 dB (typ)

■SFDR (fIN = 10 MHz) −78.7 dB (typ)

■Power Consumption, 80 Msps 78.6 mW

Applications

■Ultrasound and Imaging

■Instrumentation

■Cellular Base Stations/Communications Receivers

■Sonar/Radar

■xDSL

■Wireless Local Loops

■Data Acquisition Systems

■DSP Front Ends

Connection Diagram

20048501

ADC10080 10-Bit 80 MSPS 3V, 78.6 mW A/D Converter

Ordering Information

Industrial (−40°C ≤ TA ≤ +85°C) NS Package

ADC10080CIMT 28 Pin TSSOP

ADC10080CIMTX 28 Pin TSSOP Tape & Reel

ADC10080EVAL Evaluation Board

Block Diagram

20048502

www.national.com 2

ADC10080

Pin Descriptions and Equivalent Circuits

Pin No. Symbol Equivalent Circuit Description

ANALOG I/O

12 VIN−

Inverting analog input signal. With a 1.2V reference the full-scale

input signal level is a differential 1.0 VP-P. This pin may be tied to

VCOM (pin 4) for single-ended operation.

13 VIN+

Non-inverting analog input signal. With a 1.2V reference the full-

scale input signal level is a differential 1.0 VP-P.

6VREF

Reference input. This pin should be bypassed to VSSA with a 0.1

µF monolithic capacitor. VREF is 1.20V nominal. This pin may be

driven by a 1.20V external reference if desired. Do not load this pin.

7VREFT

4VCOM

These pins are high impedance reference bypass pins only.

Connect a 0.1 µF capacitor from each of these pins to VSSA. These

pins should not be loaded. VCOM may be used to set the input

common input voltage, VCM.

8VREFB

DIGITAL I/O

1 CLK

Digital clock input. The range of frequencies for this input is

20 MHz to 80 MHz. The input is sampled on the rising edge of this

input.

15 DF DF = “1” Two’s Complement

DF = “0” Offset Binary

28 STBY This is the standby pin. When high, this pin sets the converter into

standby mode. When this pin is low, the converter is in active mode.

5IRS (Input Range

Select)

IRS = “VDDA” 2.0 VP-P differential input range

IRS = “VSSA” 1.5 VP-P differential input range

IRS = “Floating” 1.0 VP-P differential input range

If using both VIN+ and VIN- pins, (or differential mode), then the

peak-to-peak voltage refers to the differential voltage (VIN+ - VIN-).

3 www.national.com

ADC10080

Pin No. Symbol Equivalent Circuit Description

16–20, 23–

27 D0–D9 Digital output data. D0 is the LSB and D9 is the MSB of the binary

output word.

ANALOG POWER

2, 9, 10 VDDA

Positive analog supply pins. These pins should be connected to a

quiet 3.0V source and bypassed to analog ground with a 0.1 µF

monolithic capacitor located within 1 cm of these pins. A 4.7 µF

capacitor should also be used in parallel.

3, 11, 14 VSSA Ground return for the analog supply.

DIGITAL POWER

22 VDDIO

Positive digital supply pins for the ADC10080's output drivers. This

pin should be bypassed to digital ground with a 0.1 µF monolithic

capacitor located within 1 cm of this pin. A 4.7 µF capacitor should

also be used in parallel. The voltage on this pin should never

exceed the voltage on VDDA by more than 300 mV.

21 VSSIO

The ground return for the digital supply for the output drivers. This

pin should be connected to the ground plane, but not near the

analog circuitry.

www.national.com 4

ADC10080

Absolute Maximum Ratings (Notes 1, 2)

If Military/Aerospace specified devices are required,

please contact the National Semiconductor Sales Office/

Distributors for availability and specifications.

VDDA, VDDIO 3.9V

Voltage on Any Pin to GND −0.3V to VDDA or

VDDIO +0.3V

Input Current on Any Pin ±25 mA

Package Input Current (Note 3) ±50 mA

Package Dissipation at T = 25°C See (Note 4)

ESD Susceptibility

Human Body Model (Note 5) 2500V

Machine Model (Note 5) 250V

Soldering Temperature Infrared, 10 sec. (Note 6)235°C

Storage Temperature −65°C to +150°C

Operating Ratings (Notes 1, 2)

Operating Temperature Range −40°C ≤ TA ≤ +85°C

VDDA (Supply Voltage) +2.7V to +3.6V

VDDIO (Output Driver Supply

Voltage) +2.5V to VDDA

VREF 1.20V

|VSSA–VSSIO|≤ 100 mV

Clock Duty Cycle 30 to 70 %

Converter Electrical Characteristics

Unless otherwise specified, the following specifications apply for VSSA = VSSIO = 0V(Notes 8, 8, 9), VDDA = +3.0V, VDDIO = +2.5V,

VIN = 2 VP-P, STBY = 0V, VREF = 1.20V (External), fCLK = 80 MHz, 50% Duty Cycle, CL = 10 pF/pin. Boldface limits apply for

TA = TMIN to TMAX: all other limits TA = 25°C.(Notes 7, 8, 9)

Symbol Parameter Conditions Min Typ Max Units

STATIC CONVERTER CHARACTERISTICS

No Missing Codes Guaranteed 10 Bits

INL Integral Non-Linearity (Note 10) FIN = 500 kHz, 0 dB Full Scale −1.4 ±0.5 +1.6 LSB

DNL Differential Non-Linearity FIN = 500 kHz, 0 dB Full Scale −0.9 ±0.25 +1.0 LSB

GE Gain Error Positive Error −1.6 +0.5% +2.0 % FS

Negative Error −1.6 −0.07% +2.0 % FS

OE Offset Error (VIN+ = VIN−) −1.4 0.11 1.7 % FS

Under Range Output Code 0

Over Range Output Code 1023

FPBW Full Power Bandwidth 400 MHz

REFERENCE AND INPUT CHARACTERISTICS

VCM Common Mode Input Voltage 0.5 1.5 V

VCOM

Output Voltage for use as an input

common mode voltage (Note 15)

1.45 V

VREF Internal Reference Voltage 1.2 V

External Reverence Voltage 1.0 1.2 1.5 V

VREFTC

Internal Reference Voltage

Temperature Coefficient ±80 ppm/°C

CIN VIN Input Capacitance (each pin to

VSSA)

4 pF

POWER SUPPLY CHARACTERISTICS

IVDDA Analog Supply Current STBY = 1 5 6.3 mA

STBY 0 25 32 mA

IVDDIO Digital Supply Current (Note 12) STBY = 1, fIN= 0 Hz 0 mA

STBY 0, fIN = 0 Hz 1.2 1.4 mA

PWR Power Consumption (Note 13) STBY = 1 15 18.9 mW

STBY = 0 78.6 100.2 mW

5 www.national.com

ADC10080

DC and Logic Electrical Characteristics Unless otherwise specified, the following specifications apply

for VSSA = VSSIO = 0V, VDDA = +3.0V, VDDIO = +2.5V, VIN = 2 VP-P, STBY = 0V, VREF = 1.20V (External), fCLK = 80 MHz, 50% Duty

Cycle, CL = 10 pF/pin. Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25°C (Notes 7, 8, 9)

Symbol Parameter Conditions Min Typ Max Units

CLK, DF, STBY, SENSE

Logical “1” Input Voltage 2 V

Logical “0” Input Voltage 0.8 V

Logical “1” Input Current +10 µA

Logical “0” Input Current −10 µA

D0–D9 OUTPUT CHARACTERISTICS

Logical “1” Output Voltage IOUT = −0.5 mA VDDIO−0.2 V

Logical “0” Output Voltage IOUT = 1.6 mA 0.4 V

DYNAMIC CONVERTER CHARACTERISTICS (Note 11)

ENOB Effective Number of Bits

fIN = 10.0 MHz 9.3

9.1

9.5 Bits

fIN = 39 MHz 9.3

8.9

9.5 Bits

SNR Signal-to-Noise Ratio

fIN = 10.0 MHz 58.5

57.7

59.5 dB

fIN = 39 MHz 58.0

57.0

59.2 dB

SINAD Signal-to-Noise Ratio + Distortion

fIN = 10.0 MHz 58.0

56.3 59.2 dB

fIN = 39 MHz 57.6

55.6 59.0 dB

2nd HD 2nd Harmonic

fIN = 10.0 MHz −74.1

−68.7 −87.0 dBc

fIN = 39 MHz −69.5

−62.7 −82 dBc

3rd HD 3rd Harmonic

fIN = 10.0 MHz −65

−58.6 −72.3 dBc

fIN = 39 MHz −64.7

−57.6 −74.5 dBc

THD Total Harmonic Distortion (First 6

Harmonics)

fIN = 10.0 MHz −65

−58.6 −72.3 dB

fIN = 39 MHz −64.7

−57.6 −74.5 dB

SFDR Spurious Free Dynamic Range

(Excluding 2nd and 3rd Harmonic)

fIN = 10.0 MHz −70.8

−68.2 −78.7 dBc

fIN = 39 MHz −72

−68 −78.8 dBc

www.national.com 6

ADC10080

AC Electrical Characteristics

Unless otherwise specified, the following specifications apply for VSSA = VSSIO = 0V, VDDA = +3.0V, VDDIO = +2.5V, VIN = 2 VP-P,

STBY = 0V, VREF = 1.20V, (Externally Supplied) fCLK = 80 MHz, 50% Duty Cycle, CL = 10 pF/pin. Boldface limits apply for TA =

TMIN to TMAX: all other limits TA = 25°C (Notes 7, 8, 9, 10)

Symbol Parameter Conditions Min

(Note 10)

Typ

(Note 10)

Max

(Note 10) Units

CLK, DF, STBY, SENSE

fCLK1Maximum Clock Frequency 80 MHz (min)

fCLK2Minimum Clock Frequency 20 MHz

tCH Clock High Time 6.25 ns

tCL Clock Low Time 6.25 ns

Conversion Latency 6Cycles

tOD

Data Output Delay after a Rising Clock

Edge

T = 25°C 2 3.5 5 ns

1 6ns

tAD Aperture Delay 1 ns

tAJ Aperture Jitter 2 ps (RMS)

Over Range Recovery Time

Differential VIN step from

±3V to 0V to get accurate

conversion

Clock Cycle

tSTBY Standby Mode Exit Cycle 20 Cycles

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is

functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed

specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test

conditions.

Note 2: All voltages are measured with respect to GND = VSSA = VSSIO = 0V, unless otherwise specified.

Note 3: When the voltage at any pin exceeds the power supplies (VIN < VSSA or VIN > VDDA), the current at that pin should be limited to 25 mA. The 50 mA maximum

package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 25 mA to two.

Note 4: The absolute maximum junction temperature (TJmax) for this device is 150°C. The maximum allowable power dissipation is dictated by TJmax, the

junction-to-ambient thermal resistance (θJA), and the ambient temperature (TA), and can be calculated using the formula PDMAX = (TJmax − TA)/θJA. In the 28-

pin TSSOP, θJA is 96°C/W, so PDMAX = 1,302 mW at 25°C and 677 mW at the maximum operating ambient temperature of 85°C. Note that the power dissipation

of this device under normal operation will typically be about 78.6 mW. The values for maximum power dissipation listed above will be reached only when the

ADC10080 is operated in a severe fault condition.

Note 5: Human body model is 100 pF capacitor discharged through a 1.5 kΩ resistor. Machine model is 220 pF discharged through 0Ω.

Note 6: The 235°C reflow temperature refers to infrared reflow. For Vapor Phase Reflow (VPR) the following conditions apply: Maintain the temperature at the

top of the package body above 183°C for a minimum of 60 seconds. The temperature measured on the package body must not exceed 220°C. Only one excursion

above 183°C is allowed per reflow cycle. The analog inputs are protected as shown below. Input voltage magnitude up to 500 mV beyond the supply rails will not

damage this device. However, input errors will be generated if the input goes above VDDA or VDDIO and below VSSA or VSSIO.

20048507

Note 7: To guarantee accuracy, it is required that |VDDA–VDDIO| ≤ 100 mV and separate bypass capacitors are used at each power supply pin.

Note 8: With the test condition for 2 VP-P differential input, the 10-bit LSB is 1.95 mV.

Note 9: Typical figures are at TA = TJ = 25°C and represent most likely parametric norms. Test limits are guaranteed to National's AOQL (Average Outgoing

Quality Level).

Note 10: Timing specifications are tested at TTL logic levels, VIL = 0.4V for a falling edge, and VIH = 2.4V for a rising edge.

Note 11: Optimum dynamic performance will be obtained by keeping the reference input at +1.2V.

Note 12: IVDDIO is the current consumed by the switching of the output drivers and is primarily determined by load capacitance on the output pins, the supply

voltage, VDDIO, and the rate at which the outputs are switching (which is signal dependent). IDR = VDR x (C0 x f0 + C1 x f1 + C2 + f2 +....C11 x f11) where VDR is the

output driver supply voltage, Cn is the total load capacitance on the output pin, and fn is the average frequency at which the pin is toggling.

Note 13: Power consumption includes output driver power. (fIN = 0 MHz).

Note 14: The input bandwidth is limited using a 10 pF capacitor between VIN− and VIN+.

Note 15: VCOM is typical value, measured at room temperature. It is not guaranteed by test. This pin should not be loaded.

7 www.national.com

ADC10080

Specification Definitions

APERTURE DELAY is the time after the rising edge of the

clock to when the input signal is acquired or held for conver-

sion.

APERTURE JITTER (APERTURE UNCERTAINTY) is the

variation in aperture delay from sample to sample. Aperture

jitter manifests itself as noise in the output.

COMMON MODE VOLTAGE (VCM) is the d.c. potential

present at both signal inputs to the ADC.

CONVERSION LATENCY See PIPELINE DELAY.

DIFFERENTIAL NON-LINEARITY (DNL) is the measure of

the maximum deviation from the ideal step size of 1 LSB.

DUTY CYCLE is the ratio of the time that a repetitive digital

waveform is high to the total time of one period. The specifi-

cation here refers to the ADC clock input signal.

EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE

BITS) is another method of specifying Signal-to-Noise and

Distortion or SINAD. ENOB is defined as (SINAD - 1.76) / 6.02

and states that the converter is equivalent to a perfect ADC

of this (ENOB) number of bits.

FULL POWER BANDWIDTH is a measure of the frequency

at which the reconstructed output fundamental drops 3 dB

below its low frequency value for a full scale input.

GAIN ERROR is the deviation from the ideal slope of the

transfer function. It can be calculated as:

Gain Error = Positive Full-Scale Error − Negative Full-Scale

Error

INTEGRAL NON LINEARITY (INL) is a measure of the de-

viation of each individual code from a line drawn from negative

full scale through positive full scale. The deviation of any given

code from this straight line is measured from the center of that

code value.

MISSING CODES are those output codes that will never ap-

pear at the ADC outputs. The ADC10080 is guaranteed not

to have any missing codes.

NEGATIVE FULL SCALE ERROR is the difference between

the input voltage (VIN+ − VIN−) just causing a transition from

negative full scale to the first code and its ideal value of

0.5 LSB.

OFFSET ERROR is the input voltage that will cause a tran-

sition from a code of 01 1111 1111 to a code of 10 0000 0000.

OUTPUT DELAY is the time delay after the rising edge of the

clock before the data update is presented at the output pins.

PIPELINE DELAY (LATENCY) is the number of clock cycles

between initiation of conversion and when that data is pre-

sented to the output driver stage. Data for any given sample

is available at the output pins the Pipeline Delay plus the Out-

put Delay after the sample is taken. New data is available at

every clock cycle, but the data lags the conversion by the

pipeline delay.

POSITIVE FULL SCALE ERROR is the difference between

the actual last code transition and its ideal value of 1½ LSB

below positive full scale.

SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in

dB, of the rms value of the input signal to the rms value of the

sum of all other spectral components below one-half the sam-

pling frequency, not including harmonics or DC.

SIGNAL TO NOISE PLUS DISTORTION (S/N+D or

SINAD) Is the ratio, expressed in dB, of the rms value of the

input signal to the rms value of all of the other spectral com-

ponents below half the clock frequency, including harmonics

but excluding DC.

SPURIOUS FREE DYNAMIC RANGE (SFDR) is the differ-

ence, expressed in dB, between the rms values of the input

signal and the peak spurious signal, where a spurious signal

is any signal present in the output spectrum that is not present

at the input.

TOTAL HARMONIC DISTORTION (THD) is the ratio, ex-

pressed in dBc, of the rms total of the first six harmonic levels

at the output to the level of the fundamental at the output. THD

is calculated as:

where f1 is the RMS power of the fundamental (output) fre-

quency and f2 through f6 are the RMS power in the first 6

harmonic frequencies.

Second Harmonic Distortion (2nd Harm) is the difference

expressed in dB, between the RMS power in the input fre-

quency at the output and the power in its 2nd harmonic level

at the output.

Third Harmonic Distortion (3rd Harm) is the difference, ex-

pressed in dB, between the RMS power in the input frequency

at the output and the power in its 3rd harmonic level at the

output.

www.national.com 8

ADC10080

Timing Diagram

20048509

FIGURE 1. Clock and Data Timing Diagram

Transfer Characteristics

20048510

FIGURE 2. Input vs. Output Transfer Characteristic

9 www.national.com

ADC10080

Typical Performance Characteristics Unless otherwise specified, the following specifications apply:

VSSA = VSSIO = 0V, VDDA = +3.0V, VDDIO = +2.5V, VIN = 2 VP-P, STBY = 0V, VREF = 1.2V (External), fCLK = 80 MHz, fIN , 39 MHz,

50% Duty Cycle.

DNL

20048512

DNL vs. fCLK

20048515

DNL vs. Clock Duty Cycle (DC input)

20048513

DNL vs. Temperature

20048516

INL

20048514

INL vs. fCLK

20048517

www.national.com 10

ADC10080

INL vs. Clock Duty Cycle

20048518

SNR vs. VDDIO

20048519

SNR vs. VDDA

20048520

SNR vs. fCLK

20048521

INL vs. Temperature

20048522

SNR vs. Clock Duty Cycle

20048523

11 www.national.com

ADC10080

SNR vs. Temperature

20048524

THD vs. VDDA

20048525

THD vs. VDDIO

20048526

THD vs. fCLK

20048527

SNR vs. IRS

20048528

THD vs. IRS

20048529

www.national.com 12

ADC10080

SINAD vs. VDDA

20048530

SINAD vs. VDDIO

20048531

THD vs. Clock Duty Cycle

20048532

SINAD vs. Clock Duty Cycle

20048533

THD vs. Temperature

20048534

SINAD vs. Temperature

20048535

13 www.national.com

ADC10080

SINAD vs. fCLK

20048536

SFDR vs. VDDIO

20048537

SINAD vs. IRS

20048538

SFDR vs. fCLK

20048539

SFDR vs. VDDA

20048540

SFDR vs. IRS

20048541

www.national.com 14

ADC10080

SFDR vs. Clock Duty Cycle

20048542

Spectral Response @ 10 MHz Input

20048543

SFDR vs. Temperature

20048544

Spectral Response @ 39 MHz Input

20048545

Power Consumption vs. fCLK

20048546

15 www.national.com

ADC10080

Functional Description

The ADC10080 uses a pipeline architecture and has error

correction circuitry to help ensure maximum performance.

Differential analog input signals are digitized to 10 bits. In dif-

ferential mode each analog input signal should have a peak-

to-peak voltage equal to 1.0V, 0.75V or 0.5V, depending on

the state of the IRS pin (pin 5), and be centered around VCM

and be 180° out of phase with each other. If single ended

operation is desired, VIN- may be tied to the VCOM pin (pin 4).

A single ended input signal may then be applied to VIN+, and

should have a mid range value of VCOM. The signal amplitude

should be 2.0V, 1.5V or 1.0V peak-to-peak, depending on the

state or the IRS pin (pin 5).

Applications Information

1.0 ANALOG INPUTS

The ADC10080 has two analog signal inputs, VIN+ and VIN−.

These two pins form a differential input pair. There is one

common mode pin VCOM that may be used to set the common

mode input voltage.

1.1 REFERENCE PINS

The ADC10080 is designed to operate with a 1.2V reference.

The voltages at VCOM, VREFT, and VREFB are derived from the

reference voltage. It is very important that all grounds asso-

ciated with the reference voltage and the input signal make

connection to the analog ground plane at a single point to

minimize the effects of noise currents in the ground path. The

three Reference Bypass Pins VREF, VREFT and VREFB, are

made available for bypass purposes only. These pins should

each be bypassed to ground with a 0.1 µF capacitor. DO NOT

LOAD these pins.

1.2 VCOM PIN

This pin supplies a voltage for possible use to set the common

mode input voltage. This pin may also be connected to VIN-,

so that VIN+ may be used as a single ended input. This pin

should be bypassed with at least a 0.1 uF capacitor. Do not

load this pin.

1.3 SIGNAL INPUTS

The signal inputs are VIN+ and VIN−. The input signal ampli-

tude is defined as VIN+ − VIN− and is represented in Figure

20048547

FIGURE 3. Input Voltage Waveforms for a 2VP-P

Differential Input

A single ended input signal is shown in Figure 4.

20048548

FIGURE 4. Input Voltage Waveform for a 2VP-P Single

Ended Input

The internal switching action at the analog inputs causes en-

ergy to be output from the input pins. As the driving source

tries to compensate for this, it adds noise to the signal. To

prevent this, use 18Ω series resistors at each of the signal

input pins with a 25 pF capacitor across the inputs, as shown

in Figure 5. These components should be placed close to the

ADC because the input pins of the ADC is the most sensitive

part of the system and this is the last opportunity to filter the

input. The two 18Ω resistors and the 25 pF capacitor form a

low-pass filter with a -3 dB frequency of 177 MHz.

1.4 CLK PIN

The CLK signal controls the timing of the sampling process.

Drive the clock input with a stable, low jitter clock signal in the

frequency range indicated in the AC Electrical Characteristics

Table with rise and fall times of less than 2 ns. The trace car-

rying the clock signal should be as short as possible and

should not cross any other signal line, analog or digital, not

even at 90°. The CLK signal also drives an internal state ma-

chine. If the CLK is interrupted, or its frequency is too low, the

charge on internal capacitors can dissipate to the point where

the accuracy of the output data will degrade. This is what limits

the lowest sample rate. The duty cycle of the clock signal can

affect the performance of any A/D Converter. Because

achieving a precise duty cycle is difficult, the ADC10080 is

designed to maintain performance over a range of duty cy-

cles. While it is specified and performance is guaranteed with

a 50% clock duty cycle, performance is typically maintained

with minimum clock low and high times indicated in the AC

Electrical Characteristics Table. Both minimum high and low

times may not be held simultaneously.

1.5 STBY PIN

The STBY pin, when high, holds the ADC10080 in a power-

down mode to conserve power when the converter is not

being used. The power consumption in this state is 15 mW.

The output data pins are undefined in this mode. Power con-

sumption during power-down is not affected by the clock

frequency, or by whether there is a clock signal present. The

data in the pipeline is corrupted while in power down.

1.6 DF PIN

The DF (Data Format) pin, when high, forces the ADC10080

to output the 2’s complement data format. When DF is tied

low, the output format is offset binary.

1.7 IRS PIN

The IRS (Input Range Select) pin defines the input signal am-

plitude that will produce a full scale output. The table below

describes the function of the IRS pin.

www.national.com 16

ADC10080

TABLE 1. IRS Pin Functions

IRS Pin Full-Scale Input

VDDA 2.0VP-P

VSSA 1.5VP-P

Floating 1.0VP-P

1.8 OUTPUT PINS

The ADC10080 has 10 TTL/CMOS compatible Data Output

pins. The offset binary data is present at these outputs while

the DF and STBY pins are low. Be very careful when driving

a high capacitance bus. The more capacitance the output

drivers must charge for each conversion, the more instanta-

neous digital current flows through VDDIO and VSSIO. These

large charging current spikes can cause on-chip noise and

couple into the analog circuitry, degrading dynamic perfor-

mance. Adequate bypassing, limiting output capacitance and

careful attention to the ground plane will reduce this problem.

Additionally, bus capacitance beyond the specified

10 pF/pin will cause tOD to increase, making it difficult to prop-

erly latch the ADC output data. The result could be an appar-

ent reduction in dynamic performance. To minimize noise due

to output switching, minimize the load currents at the digital

outputs. This can be done by minimizing load capacitance

and by connecting buffers between the ADC outputs and any

other circuitry, which will isolate the outputs from trace and

other circuit capacitances and limit the output currents, which

could otherwise result in performance degradation. Only one

driven input should be connected to the ADC output pins.

1.9 APPLICATION SCHEMATICS

The following figures show simple examples of using the

ADC10080. Figure 5 shows a typical differentially driven in-

put. Figure 6 shows a single ended application circuit.

20048549

FIGURE 5. A Simple Application Using a Differential Driving Source

17 www.national.com

ADC10080

20048550

FIGURE 6. A Simple Application Using a Single Ended Driving Source

www.national.com 18

ADC10080

Physical Dimensions inches (millimeters) unless otherwise noted

28-Lead TSSOP Package

Ordering Number ADC10080CIMT

NS Package Number MTC28

19 www.national.com

ADC10080

Notes

ADC10080 10-Bit 80 MSPS 3V, 78.6 mW A/D Converter

For more National Semiconductor product information and proven design tools, visit the following Web sites at:

Products Design Support

Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench

Audio www.national.com/audio Analog University www.national.com/AU

Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes

Data Converters www.national.com/adc Distributors www.national.com/contacts

Displays www.national.com/displays Green Compliance www.national.com/quality/green

Ethernet www.national.com/ethernet Packaging www.national.com/packaging

Interface www.national.com/interface Quality and Reliability www.national.com/quality

LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns

Power Management www.national.com/power Feedback www.national.com/feedback

Switching Regulators www.national.com/switchers

LDOs www.national.com/ldo

LED Lighting www.national.com/led

PowerWise www.national.com/powerwise

Serial Digital Interface (SDI) www.national.com/sdi

Temperature Sensors www.national.com/tempsensors

Wireless (PLL/VCO) www.national.com/wireless

THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION

(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY

OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO

SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,

IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS

DOCUMENT.

TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT

NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL

PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR

APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND

APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE

NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.

EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO

LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE

AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR

PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY

RIGHT.

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR

SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL

COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:

Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and

whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected

to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform

can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.

National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other

brand or product names may be trademarks or registered trademarks of their respective holders.

For the most current product information visit us at www.national.com

National Semiconductor

Americas Technical

Support Center

Email:

new.feedback@nsc.com

Tel: 1-800-272-9959

National Semiconductor Europe

Technical Support Center

Email: europe.support@nsc.com

German Tel: +49 (0) 180 5010 771

English Tel: +44 (0) 870 850 4288

National Semiconductor Asia

Pacific Technical Support Center

Email: ap.support@nsc.com

National Semiconductor Japan

Technical Support Center

Email: jpn.feedback@nsc.com

www.national.com

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,

and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should

obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are

sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard

warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where

mandated by government requirements, testing of all parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and

applications using TI components. To minimize the risks associated with customer products and applications, customers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,

or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a

warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual

property of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied

by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive

business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional

restrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all

express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not

responsible or liable for any such statements.

TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably

be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing

such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and

acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products

and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be

provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in

such safety-critical applications.

TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are

specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military

specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at

the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.

TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are

designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated

products in automotive applications, TI will not be responsible for any failure to meet such requirements.

Following are URLs where you can obtain information on other Texas Instruments products and application solutions:

Products Applications

Audio www.ti.com/audio Communications and Telecom www.ti.com/communications

Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers

Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps

DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy

DSP dsp.ti.com Industrial www.ti.com/industrial

Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical

Interface interface.ti.com Security www.ti.com/security

Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Mobile Processors www.ti.com/omap

Wireless Connectivity www.ti.com/wirelessconnectivity

TI E2E Community Home Page e2e.ti.com

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265