LM48555 LM48555 Ceramic Speaker Driver Literature Number: SNAS400 LM48555 Ceramic Speaker Driver General Description Key Specifications The LM48555 is an audio power amplifier designed to drive ceramic speakers in applications such as cell phones, smart phones, PDAs and other portable devices. The LM48555 produces 15.7VP-P with less than 1% THD+N while operating from a 3.2V power supply. The LM48555 features a low power shutdown mode, and differential inputs for improved noise rejection. The LM48555 includes advanced click and pop suppression that eliminates audible turn-on and turn-off transients. Additionally, the integrated boost regulator features a soft start function that minimizes transient current during power-up Boomer audio power amplifiers were designed specifically to provide high quality output power with a minimal number of external components. The LM48555 does not require bootstrap capacitors, or snubber circuits. The LM48555 is unity-gain stable and uses external gain-setting resistors. IDDQ (Boost Converter + Amplifier) at VDD = 5V 7.5mA (typ) Output Voltage Swing VDD = 3.2V, THD 1% Power Supply Rejection Ratio f = 217Hz 15.7VP-P (typ) 80dB (typ) Features Fully differential amplifier Externally configurable gain Soft start function Low power shutdown mode Under voltage lockout Applications Mobile phones PDA's Digital cameras Typical Application 300099c9 * CF+ and CF- are optional. Refer to "Selecting Input and Feedback Capacitor and Resistor for Audio Amplifier" section. FIGURE 1. Typical Audio Amplifier Application Circuit Boomer(R) is a registered trademark of National Semiconductor Corporation. (c) 2007 National Semiconductor Corporation 300099 www.national.com LM48555 Ceramic Speaker Driver March 2007 LM48555 Connection Diagrams LM48555TL Bumps Down View LM48555TL Marking Drawing 30009956 Top View X = One digit date code V = Die traceability G = Boomer Family I4 = LM48555TL 300099c8 Top View Order Number LM48555TL See NS Package Number TLA12Z1A TLA12 Package View (Bumps Up) 30009931 www.national.com 2 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VDD) Storage Temperature Input Voltage Power Dissipation (Note 3) ESD Susceptibility (Note 4) ESD Susceptibility (Note 5) 150C JA (Note 10) 114C/W Operating Ratings 9.5V -65C to +150C -0.3V to VDD + 0.3V Internally limited 2000V 200V Temperature Range TMIN TA TMAX (Note 10) -40C TA +85C 2.7V VDD 6.5V Supply Voltage (VDD) Electrical Characteristics (Notes 1, 2) The following specifications apply for VDD = 3.2V and the conditions shown in "Typical Audio Amplifier Application Circuit" (see Figure 1), unless otherwise specified. Limits apply for TA = 25C. LM48555 Symbol Parameter Conditions Typical (Note 6) Limit (Notes 7, 8) Units (Limits) VIN = 0V, No Load VDD = 5.0V 7.5 mA VDD = 3.6V 10 mA IDD Quiescent Power Supply Current in Boosted Ringer Mode ISD Shutdown Current VLH Logic High Threshold Voltage 1.2 V (min) VLL Logic Low Threshold Voltage 0.4 V (max) RPULLDOWN Pulldown Resistor on SD pin 53 k (min) TWU Wake-up Time CSS = 0.1F Boost Converter Output Voltage Voltage on VAMP Pin VOUT Output Voltage Swing THD+N OS VDD = 3.2V 12 15 mA (max) SD = GND (Note 9) 0.1 1 A (max) 80 100 ms 8 8.5 7.5 V (max) V (min) THD = 1% (max); f = 1kHz 15.7 15 VP-P (min) Total Harmonic Distortion + Noise VOUT = 14VP-P, f = 1kHz 0.05 0.5 % (max) Output Noise A-Weighted Filter, VIN = 0V 70 PSRR Power Supply Rejection Ratio VRIPPLE = 200mVp-p, f = 217Hz, AV = 20dB 80 ISW Switch Current Limit VOS Output Offset Voltage CMRR Common Mode Rejection Ratio UVLO RDS(ON) VAMP V 72 2 dB (min) A 0.5 4.5 mV (max) 70 65 dB (min) Under-Voltage Lock Out 2.5 2.6 V (max) Switch ON resistance 0.3 Input referred 3 www.national.com LM48555 Junction Temperature Thermal Resistance Absolute Maximum Ratings (Notes 1, 2) LM48555 Note 1: All voltages are measured with respect to the GND pin, unless otherwise specified. Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA, and the ambient temperature, TA. The maximum allowable power dissipation is PDMAX = (TJMAX - TA) / JA or the given in Absolute Maximum Ratings, whichever is lower. Note 4: Human body model, 100pF discharged through a 1.5k resistor. Note 5: Machine Model, 220pF-240pF discharged through all pins. Note 6: Typicals are measured at 25C and represent the parametric norm. Note 7: Limits are guaranteed to National's AOQL (Average Outgoing Quality Level). Note 8: Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis. Note 9: Shutdown current is measured in a normal room environment. The SD pin should be driven as close as possible to GND for minimum shutdown current. Note 10: The value for JA is measured with the LM48555 mounted on a 3" x 1.5" (76.2mm x 3.81mm) four layer board. The copper thickness for all four layers is 0.5oz (roughly 0.18mm). www.national.com 4 LM48555 Typical Performance Characteristics THD+N vs Frequency VO = 4.95VRMS, VDD = 3.2V, ZL = 1F + 20 THD+N vs Frequency VO = 4.95VRMS, VDD = 4.2V, ZL = 1F + 20 30009950 30009951 THD+N vs Frequency VO = 4.95VRMS, VDD = 5V, ZL = 1F + 20 THD+N vs Output Voltage Swing VDD = 3.2V, ZL = 1F + 20 30009964 30009952 THD+N vs Output Voltage Swing VDD = 4.2V, ZL = 1F + 20 THD+N vs Output Voltage Swing VDD = 5V, ZL = 1F + 20 30009965 30009969 5 www.national.com LM48555 CMRR vs Frequency VDD = 3.2V, ZL = 1F + 20 VIN = 100mVP-P CMRR vs Frequency VDD = 4.2V, ZL = 1F + 20 VIN = 100mVP-P 30009957 30009958 CMRR vs Frequency VDD = 5V, ZL = 1F + 20 VIN = 100mVP-P PSRR vs Frequency VDD = 3.2V, ZL = 1F + 20 VRIPPLE = 200mVP-P 30009961 30009959 PSRR vs Frequency VDD = 5V, ZL = 1F + 20 VRIPPLE = 200mVP-P PSRR vs Frequency VDD = 4.2V, ZL = 1F + 20 VRIPPLE = 200mVP-P 30009963 30009962 www.national.com 6 LM48555 Inductor Current vs Output Voltage Swing ZL = 1F + 20, f = 1kHz, VDD = 3V, 4.2V, 5V Supply Current vs Supply Voltage 30009967 30009960 7 www.national.com LM48555 Application Information both increased internal IC power dissipation as well as permanent loudspeaker damage. CHARACTERISTICS OF CERAMIC SPEAKERS Because of their ultra-thin profile piezoelectric ceramic speakers are ideal for portable applications. Piezoelectric materials have high dielectric constants and their component electrical property is like a capacitor. Therefore, piezoelectric ceramic speakers essentially represent capacitive loads over frequency. Because these speakers are capacitive rather than resistive, they require less current than traditional moving coil speakers. However, ceramic speakers require high driving voltages (approximately 15VP-P). To achieve these high output voltages in battery operated applications, the LM48555 integrates a boost converter with an audio amplifier. High quality piezoelectric ceramic speakers are manufactured by TayioYuden (www.t-yuden.com) and muRata (www.murata.com). Tayio Yuden's MLS-A Series Ceramic Speaker and Murata's piezoelectric speaker VSL series are recommended. BOOST CONVERTER POWER DISSIPATION At higher duty cycles, the increased ON-time of the switch FET means the maximum output current will be determined by power dissipation within the LM48555 FET switch. The switch power dissipation from ON-time conduction is calculated by Equation 2. PD(SWITCH) = DC x (IINDUCTOR(AVE))2 x RDS(ON) (W) where DC is the duty cycle. There will be some switching losses in addition to the power loss calculated in Eqaution 3, so some derating needs to be applied when calculating IC power dissipation. See "Maximum Power Dissipation" section. MAXIMUM AMPLIFIER POWER DISSIPATION Power dissipation is a major concern when designing a successful amplifier, whether the amplifier is bridged or singleended. A direct consequence of the increased power delivered to the load by a bridge amplifier is an increase in internal power dissipation. Since the amplifier portion of the LM48555 has two operational amplifiers, the maximum internal power dissipation is 4 times that of a single-ended amplifier. The maximum power dissipation for a given BTL application can be derived from Equation 3. DIFFERENTIAL AMPLIFIER EXPLANATION The LM48555 includes a fully differential audio amplifier that features differential input and output stages. Internally this is accomplished by two circuits: a differential amplifier and a common mode feedback amplifier that adjusts the output voltages so that the average value remains VDD/2. When setting the differential gain, the amplifier can be considered to have "halves". Each half uses an input and feedback resistor (RIN_ and RF_) to set its respective closed-loop gain (see Figure 1). With RIN+ = RIN- and RF+ = RF-, the gain is set at -RF/RIN for each half. This results in a differential gain of AVD = -RF/RIN PDMAX(AMP) = (2VDD2) / (2RO) (W) (3) MAXIMUM TOTAL POWER DISSIPATION The total power dissipation for the LM48555 can be calculated by adding Equation 2 and Equation 3 together to establish Equation 4: (1) PDMAX(TOTAL) = (2VDD2) / (2EFF2RO) (W) It is extremely important to match the input resistors, as well as the feedback resistors to each other for best amplifier performance. A differential amplifier works in a manner where the difference between the two input signals is amplified. In most applications, this would require input signals that are 180 out of phase with each other. The LM48555 can be used, however, as a single-ended input amplifier while still retaining its fully differential benefits. In fact, completely unrelated signals may be placed at the input pins. The LM48555 simply amplifies the difference between them. The LM48555 provides what is known as a "bridged mode" output (bridge-tied-load, BTL). This results in output signals at OUT+ and OUT- that are 180 out of phase with respect to each other. Bridged mode operation is different from the traditional single-ended amplifier configuration that connects the load between the amplifier output and ground. A bridged amplifier design has advantages over the single-ended configuration: it provides differential drive to the load, thus doubling maximum possible output swing for a specific supply voltage. Up to four times the output power is possible compared with a single-ended amplifier under the same conditions. A bridged configuration, such as the one used in the LM48555, also creates a second advantage over single-ended amplifiers. Since the differential outputs, OUT+ and OUT-, are biased at half-supply, no net DC voltage exists across the load. This assumes that the input resistor pair and the feedback resistor pair are properly matched. BTL configuration eliminates the output coupling capacitor required in single supply, single-ended amplifier configurations. If an output coupling capacitor is not used in a single-ended output configuration, the half-supply bias across the load would result in www.national.com (2) (4) where EFF = Efficiency of boost converter The result from Equation 4 must not be greater than the power dissipation that results from Equation 5: PDMAX = (TJMAX - TA) / JA (W) (5) For the TLA12Z1A, JA = 114C/W. TJMAX = 150C for the LM48555. Depending on the ambient temperature, TA, of the system surroundings, Equation 5 can be used to find the maximum internal power dissipation supported by the IC packaging. If the result of Equation 4 is greater than that of Equation 5, then either the supply voltage must be decreased, the load impedance increased or TA reduced. For typical applications, power dissipation is not an issue. Power dissipation is a function of output power and thus, if typical operation is not around the maximum power dissipation point, the ambient temperature may be increased accordingly. STARTUP SEQUENCE Correct startup sequencing is important for optimal device performance. Using the correct startup sequence will improve click and pop performance as well as avoid transients that could reduce battery life. The device should be in Shutdown mode when the supply voltage is applied. Once the supply voltage has been supplied the device can be released from Shutdown mode. SHUTDOWN FUNCTION In many applications, a microcontroller or microprocessor output is used to control the shutdown circuitry to provide a 8 based on desired low frequency response, turn-on pops can be minimized. The LM48555 is unity-gain stable which gives the designer maximum system flexibility. However, to drive ceramic speakers, a typical application requires a closed-loop differential gain of 10V/V. In this case, feedback capacitors (CF+, CF-) may be needed as shown in Figure 1 to bandwidth limit the amplifier. If the available input signal is bandwith limited, then capacitors CF+ and CF- can be eliminated. These feedback capacitors create a low pass filter that eliminates possible high frequency noise. Care should be taken when calculating the -3dB frequency (from equation 6) because an incorrect combination of RF and CF will cause rolloff before the desired frequency. BOOTSTRAP PIN The bootstrap pin provides a voltage supply for the internal switch driver. Connecting the bootstrap pin to VAMP (See Figure 1) allows for a higher voltage to drive the gate of the switch thereby reducing the RDS(ON). This configuration is necessary in applications with heavier loads. The bootstrap pin can be connected to VDD when driving lighter loads to improve device performance (IDD, THD+N, Noise, etc.). PROPER SELECTION OF EXTERNAL COMPONENTS Proper selection of external components in applications using integrated power amplifiers, and switching DC-DC converters, is critical for optimizing device and system performance. Consideration to component values must be used to maximize overall system quality. The best capacitors for use with the switching converter portion of the LM48555 are multi-layer ceramic capacitors. They have the lowest ESR (equivalent series resistance) and highest resonance frequency, which makes them optimum for high frequency switching converters. When selecting a ceramic capacitor, only X5R and X7R dielectric types should be used. Other types such as Z5U and Y5F have such severe loss of capacitance due to effects of temperature variation and applied voltage, they may provide as little as 20% of rated capacitance in many typical applications. Always consult capacitor manufacturer's data curves before selecting a capacitor. High-quality ceramic capacitors can be obtained from Taiyo-Yuden and Murata. f-3dB = 1 / 2RF*CF (6) SELECTING OUTPUT CAPACITOR (CO) FOR BOOST CONVERTER A single 4.7F to 10F ceramic capacitor will provide sufficient output capacitance for most applications. If larger amounts of capacitance are desired for improved line support and transient response, tantalum capacitors can be used. Aluminum electrolytics with ultra low ESR such as Sanyo Oscon can be used. Typical electrolytic capacitors are not suitable for switching frequencies above 500 kHz because of significant ringing and temperature rise due to self-heating from ripple current. An output capacitor with excessive ESR can also reduce phase margin and cause instability. In general, if electrolytics are used, it is recommended that they be paralleled with ceramic capacitors to reduce ringing, switching losses, and output voltage ripple. POWER SUPPLY BYPASSING As with any amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection. The capacitor location on both V1 and VDD pins should be as close to the device as possible. SELECTING A POWER SUPPLY BYPASS CAPACITOR A supply bypass capacitor is required to serve as an energy reservoir for the current which must flow into the coil each time the switch turns on. This capacitor must have extremely low ESR, so ceramic capacitors are the best choice. A nominal value of 4.7F is recommended, but larger values can be used. Since this capacitor reduces the amount of voltage ripple seen at the input pin, it also reduces the amount of EMI passed back along that line to other circuitry. SELECTING INPUT AND FEEDBACK CAPACITORS AND RESISTOR FOR AUDIO AMPLIFIER Special care must be taken to match the values of the feedback resistors (RF+ and RF-) to each other as well as matching the input resistors (RIN+ and RIN-) to each other (see Figure 1). Because of the balanced nature of differential amplifiers, resistor matching differences can result in net DC currents across the load. This DC current can increase power consumption, internal IC power dissipation, reduce PSRR, and possibly damage the loudspeaker. To achieve best performance with minimum component count, it is highly recommended that both the feedback and input resistors match to 1% tolerance or better. The input coupling capacitors, CIN, forms a first order high pass filter which limits low frequency response. This value should be chosen based on needed frequency response. High value input capacitors are both expensive and space hungry in portable designs. A certain value capacitor is needed to couple in low frequencies without severe attenuation. Ceramic speakers used in portable systems, whether internal or external, have little ability to reproduce signals below 100Hz to 150Hz. Thus, using a high value input capacitor may not increase actual system performance. In addition to system cost and size, click and pop performance is affected by the value of the input coupling capacitor, CIN. A high value input coupling capacitor requires more charge to reach its quiescent DC voltage (nominally 1/2 VDD). This charge comes from the output via the feedback and is apt to create pops upon device enable. Thus, by minimizing the capacitor value SELECTING A SOFT-START CAPACITOR (CSS) The soft-start function charges the boost converter reference voltage slowly. This allows the output of the boost converter to ramp up slowly thus limiting the transient current at startup. Selecting a soft-start capacitor (CSS) value presents a trade off between the wake-up time and the startup transient current. Using a larger capacitor value will increase wake-up time and decrease startup transient current while the apposite effect happens with a smaller capacitor value. A general guideline is to use a capacitor value 1000 times smaller than the output capacitance of the boost converter (CO). A 0.1uF softstart capacitor is recommended for a typical application. SELECTING DIODES The external diode used in Figure 1 should be a Schottky diode. A 20V diode such as the MBR0520 from Fairchild Semiconductor or ON Semiconductor is recommended. The MBR05XX series of diodes are designed to handle a maximum average current of 0.5A. For applications exceeding 0.5A average but less than 1A, a Microsemi UPS5817 can be used. 9 www.national.com LM48555 quick, smooth transition into shutdown. Another solution is to use a single-pole, single-throw switch connected between VDD and Shutdown pins. LM48555 core (switching) losses, and wire power losses must be considered when selecting the current rating. OUTPUT VOLTAGE OF BOOST CONVERTER The output voltage is set using two internal resistors. The output voltage of the boost converter is set to 8V (typ). CALCULATING OUTPUT CURRENT OF BOOST CONVERTER (IAMP) The load current of the boost converter is related to the average inductor current by the relation: DUTY CYCLE The maximum duty cycle of the boost converter determines the maximum boost ratio of output-to-input voltage that the converter can attain in continuous mode of operation. The duty cycle for a given boost application is defined by equation 7: Duty Cycle = (VAMP+VDIODE -VDD)/(VAMP+VDIODE-VSW) IAMP = IINDUCTOR(AVE) x (1 - DC) (A) Where "DC" is the duty cycle of the application. The switch current can be found by: (7) This applies for continuous mode operation. ISW = IINDUCTOR(AVE) + 1/2 (IRIPPLE) (A) INDUCTANCE VALUE Inductor value involves trade-offs in performance. Larger inductors reduce inductor ripple current, which typically means less output voltage ripple (for a given size of output capacitor). Larger inductors also mean more load power can be delivered because the energy stored during each switching cycle is: E = L/2 x IP2 (10) Inductor ripple current is dependent on inductance, duty cycle, supply voltage and frequency: IRIPPLE = DC x (VDD-VSW) / (f x L) (A) (11) where f = switching frequency = 1MHz combining all terms, we can develop an expression which allows the maximum available load current to be calculated: (8) Where "lp" is the peak inductor current. The LM48555 will limit its switch current based on peak current. With IP fixed, increasing L will increase the maximum amount of power available to the load. Conversely, using too little inductance may limit the amount of load current which can be drawn from the output. Best performance is usually obtained when the converter is operated in "continuous" mode at the load current range of interest, typically giving better load regulation and less output ripple. Continuous operation is defined as not allowing the inductor current to drop to zero during the cycle. Boost converters shift over to discontinuous operation if the load is reduced far enough, but a larger inductor stays continuous over a wider load current range. IAMP(max) = (1-DC)x[ISW(max)-DC(V-VSW)]/2fL (A) (12) The equation shown to calculate maximum load current takes into account the losses in the inductor or turn-off switching losses of the FET and diode. DESIGN PARAMETERS VSW AND ISW The value of the FET "ON" voltage (referred to as VSW in equations 9 thru 12) is dependent on load current. A good approximation can be obtained by multiplying the on resistance (RDS(ON) of the FET times the average inductor current. The maximum peak switch current the device can deliver is dependent on duty cycle. INDUCTOR SUPPLIERS The recommended inductors for the LM48555 are the TaiyoYuden NR4012, NR3010, and CBC3225 series and Murata's LQH3NPN series. When selecting an inductor, the continuous current rating must be high enough to avoid saturation at peak currents. A suitable core type must be used to minimize www.national.com (9) EVALUATION BOARD AND PCB LAYOUT GUIDELINES For information on the LM48555 demo board and PCB layout guidelines refer to Application Notes (AN-1611). 10 LM48555 Revision History Rev Date Description 0.1 03/15/07 Initial Web Release 11 www.national.com LM48555 Physical Dimensions inches (millimeters) unless otherwise noted Thin micro SMD Order Number LM48555TL NS Package Number TLA12Z1A X1 = 1.4630.03mm X2 = 1.9700.03mm X3 = 0.6000.075mm www.national.com 12 LM48555 Notes 13 www.national.com LM48555 Ceramic Speaker Driver Notes THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2007 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530-85-86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +49 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated