MCP73861/2/3/4 Advanced Single or Dual Cell, Fully Integrated Li-Ion/Li-Polymer Charge Management Controllers Features: Description: * Linear Charge Management Controllers: - Integrated Pass Transistor - Integrated Current Sense - Reverse-Blocking Protection * High-Accuracy Preset Voltage Regulation: + 0.5% * Four Selectable Voltage Regulation Options: - 4.1V, 4.2V - MCP73861/3 - 8.2V, 8.4V - MCP73862/4 * Programmable Charge Current: 1.2A Maximum * Programmable Safety Charge Timers * Preconditioning of Deeply Depleted Cells * Automatic End-of-Charge Control * Optional Continuous Cell Temperature Monitoring * Charge Status Output for Direct LED Drive * Fault Output for Direct LED Drive * Automatic Power-Down * Thermal Regulation * Temperature Range: -40C to +85C * Packaging: 16-Pin, 4 x 4 QFN 16-Pin SOIC The MCP7386X family of devices features highly advanced linear charge management controllers for use in space-limited, cost-sensitive applications. The devices combine high-accuracy, constant voltage and current regulation, cell preconditioning, cell temperature monitoring, advanced safety timers, automatic charge termination, internal current sensing, reverse-blocking protection, charge status and fault indication in either a space-saving 16-pin 4 x 4 QFN package, or a 16-pin SOIC package. The MCP7386X provides a complete, fully functional, stand-alone charge management solution with a minimum number of external components. Applications: * * * * * * * Lithium-Ion/Lithium-Polymer Battery Chargers Personal Data Assistants (PDAs) Cellular Telephones Hand-Held Instruments Cradle Chargers Digital Cameras MP3 Players 2004-2013 Microchip Technology Inc. The MCP73861/3 is intended for applications utilizing single-cell Lithium-Ion or Lithium-Polymer battery packs, while the MCP73862/4 is intended for dual series cell Lithium-Ion or Lithium-Polymer battery packs. The MCP73861/3 has two selectable voltage-regulation options available (4.1V and 4.2V), for use with either coke or graphite anodes and operate with an input voltage range of 4.5V to 12V. The MCP73862/4 has two selectable voltage-regulation options available (8.2V and 8.4V), for use with coke or graphite anodes, and operate with an input voltage range of 8.7V to 12V. The MCP73861/2 and MCP73863/4 differ only in the function of the charge status output (STAT1) when a charge cycle has been completed. The MCP73861/2 flashes the output, while the MCP73863/4 turns the output off. Refer to Section 5.2.1 "Charge Status Outputs (STAT1, STAT2)". The MCP7386X family of devices are fully specified over the ambient temperature range of -40C to +85C. DS21893F-page 1 MCP73861/2/3/4 16-Pin SOIC VSS2 EN STAT2 16-Pin QFN STAT1 Package Types 16 15 14 13 VSET 1 12 VBAT3 VDD2 2 11 VBAT2 EP 17 VDD2 3 10 VBAT1 9 VSS3 DS21893F-page 2 THREF 6 7 THERM PROG 5 16 EN STAT1 2 15 VSS2 VSET 3 14 VBAT3 VDD1 4 13 VBAT2 12 VBAT1 VDD2 5 VSS1 6 8 PROG 7 TIMER VSS1 4 STAT2 1 THREF 8 11 VSS3 10 TIMER 9 THERM 2004-2013 Microchip Technology Inc. MCP73861/2/3/4 Typical Application 1.2A Lithium-Ion Battery Charger 2, 3 5V 4.7F 1 14 16 15 5 VBAT3 12 10, 11 V VDD VSET 4.7 F BAT THREF 6 EN 6.19 k STAT1 THERM 7 7.32 k STAT2 TIMER 8 0.1 4, 9, 13 F VSS PROG + Single Lithium-Ion - Cell Note: Pin numbers shown are for QFN package. Please refer to Section 6.0 "Applications" for details. MCP73861/3 Functional Block Diagram Direction Control VDD1 VBAT1 VDD2 VBAT2 VDD G = 0.001 4 k VREF 90 k 1 k PROG Charge Current Control Amplifier + + - IREG/12 UVLO COMPARATOR Precondition Control Precondition Comp. Constant-Voltage/ Recharge Comp. VUVLO - + EN Charge_OK Precon VBAT3 Power-On Delay 600 k (1.65 M ) - 10 k VREF 10 k + + - - 110 k Charge Termination Comparator + 11 k VREF Voltage Control Amplifier - 148.42 k Values in ( ) reflect the MCP73862/4 devices 1.58 k VREF 300.04 k Bias and Reference Generator VUVLO VREF (1.2V) VSET 10.3 k (8.58 k) THREF 100 k + - THERM Temperature Comparators 50 k + - 50 k TIMER 2004-2013 Microchip Technology Inc. VSS1 VSS2 VSS3 STAT1 Drv Stat 1 Control, IREG/12 Charge Charge Timers And Status Logic Drv Stat 2 Oscillator STAT2 Charge_OK DS21893F-page 3 MCP73861/2/3/4 1.0 ELECTRICAL CHARACTERISTICS Notice: Stresses above those listed under "Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. Absolute Maximum Ratings VDDN...............................................................................13.5V VBATN, VSET, EN, STAT1, STAT2 w.r.t. VSS .................................................................-0.3 to (VDD + 0.3)V PROG, THREF, THERM, TIMER w.r.t. VSS ............. -0.3 to 6V Maximum Junction Temperature, TJ ............Internally Limited Storage temperature .....................................-65C to +150C ESD protection on all pins: Human Body Model (1.5 k in series with 100 pF)4 kV Machine Model (200 pF, No series resistance) ...........300V DC CHARACTERISTICS Electrical Specifications: Unless otherwise indicated, all limits apply for VDD= [VREG(typ.) + 0.3V] to 12V, TA = -40C to +85C. Typical values are at +25C, VDD = [VREG (typ.) + 1.0V] Parameters Sym. Min. Typ. Max. Units Conditions VDD 4.5 -- 12 V 8.7 -- 12 V MCP73862/4 ISS -- 0.17 4 A Disabled -- 0.53 4 mA VSTART 4.25 4.5 4.65 V MCP73861/3 8.45 8.8 9.05 V MCP73862/4 Supply Input Supply Voltage Supply Current UVLO Start Threshold MCP73861/3 Operating VDD Low-to-High UVLO Stop Threshold VSTOP 4.20 4.4 4.55 V MCP73861/3 8.40 8.7 8.95 V MCP73862/4 VDD High-to-Low Voltage Regulation (Constant-Voltage Mode) Regulated Output Voltage VREG 4.079 4.1 4.121 V MCP73861/3, VSET = VSS 4.179 4.2 4.221 V MCP73861/3,VSET = VDD 8.159 8.2 8.241 V MCP73862/4, VSET = VSS 8.358 8.4 8.442 V MCP73862/4, VSET = VDD VDD = [VREG(typ.) + 1V], IOUT = 10 mA TA = -5C to +55C Line Regulation VBAT/ VBAT)| / VDD -- 0.025 0.25 %/V Load Regulation VBAT/ VBAT| -- 0.01 0.25 % IOUT = 10 mA to 150 mA VDD = [VREG(typ.)+1V] Supply Ripple Attenuation PSRR -- 60 -- dB IOUT = 10 mA, 10 Hz to 1 kHz -- 42 -- dB IOUT = 10 mA, 10 Hz to 10 kHz -- 28 -- dB IOUT = 10 mA, 10 Hz to 1 MHz VDD = [VREG(typ.)+1V] to 12V IOUT = 10 mA Output Reverse Leakage Current IDISCHARGE -- 0.23 1 A VDD < VBAT = VREG(typ.), VDD = 1.5 k to Ground Output Reverse Leakage Switchover Time IDISCHARGE -- 0 1000 ms VDD < VBAT, VDD <= 1.5 k to Ground DS21893F-page 4 _SW 2004-2013 Microchip Technology Inc. MCP73861/2/3/4 DC CHARACTERISTICS (CONTINUED) Electrical Specifications: Unless otherwise indicated, all limits apply for VDD= [VREG(typ.) + 0.3V] to 12V, TA = -40C to +85C. Typical values are at +25C, VDD = [VREG (typ.) + 1.0V] Parameters Sym. Min. Typ. Max. Units Conditions 85 100 115 mA PROG = OPEN 1020 1200 1380 mA PROG = VSS 425 500 575 mA Current Regulation (Fast Charge Constant-Current Mode) Fast Charge Current Regulation IREG PROG = 1.6 k TA= -5C to +55C Preconditioning Current Regulation (Trickle Charge Constant-Current Mode) Precondition Current Regulation IPREG 5 10 15 mA PROG = OPEN 60 120 180 mA PROG = VSS 25 50 75 mA PROG = 1.6 k TA=-5C to +55C Precondition Threshold Voltage VPTH 2.70 2.80 2.90 V MCP73861/3, VSET = VSS 2.75 2.85 2.95 V MCP73861/3, VSET = VDD 5.40 5.60 5.80 V MCP73862/4, VSET = VSS 5.50 5.70 5.90 V MCP73862/4, VSET = VDD VBAT Low-to-High Charge Termination Charge Termination Current ITERM 6 8.5 11 mA PROG = OPEN 70 90 120 mA PROG = VSS 32 41 50 mA PROG = 1.6 k TA=-5C to +55C Automatic Recharge Recharge Threshold Voltage VRTH VREG -300 mV VREG -200 mV VREG -100 mV V MCP73861/3 VREG -600 mV VREG -400 mV VREG -200 mV V MCP73862/4 VBAT High-to-Low Thermistor Reference Thermistor Reference Output Voltage VTHREF 2.475 2.55 2.625 V Thermistor Reference Source Current ITHREF 200 -- -- A Thermistor Reference Line Regulation VTHREF/ VTHREF)|/ VDD -- 0.1 0.25 %/V Thermistor Reference Load Regulation VTHREF/ VTHREF| 0.01 0.10 % TA = 25C, VDD = VREG(typ.) + 1V, ITHREF = 0 mA VDD = [VREG(typ.) + 1V] to 12V ITHREF = 0 mA to 0.20 mA Thermistor Comparator Upper Trip Threshold Upper Trip Point Hysteresis Lower Trip Threshold Lower Trip Point Hysteresis Input Bias Current VT1 1.18 1.25 1.32 V VT1HYS -- -50 -- mV VT2 0.59 0.62 0.66 V VT2HYS -- 80 -- mV IBIAS -- -- 2 A Status Indicator - STAT1, STAT2 Sink Current ISINK 4 8 12 mA Low Output Voltage VOL -- 200 400 mV ISINK = 1 mA Input Leakage Current ILK -- 0.01 1 A ISINK = 0 mA, VSTAT1,2 = 12V 2004-2013 Microchip Technology Inc. DS21893F-page 5 MCP73861/2/3/4 DC CHARACTERISTICS (CONTINUED) Electrical Specifications: Unless otherwise indicated, all limits apply for VDD= [VREG(typ.) + 0.3V] to 12V, TA = -40C to +85C. Typical values are at +25C, VDD = [VREG (typ.) + 1.0V] Parameters Sym. Min. Typ. Max. Units Input High Voltage Level VIH 1.4 -- -- V Input Low Voltage Level VIL -- -- 0.8 V Input Leakage Current ILK -- 0.01 1 A Die Temperature TSD -- 155 -- C Die Temperature Hysteresis TSDHYS -- 10 -- C Conditions Enable Input VENABLE = 12V Thermal Shutdown AC CHARACTERISTICS Electrical Specifications: Unless otherwise indicated, all limits apply for VDD = [VREG (typ.) + 0.3V] to 12V, TA = -40C to +85C. Typical values are at +25C, VDD = [VREG (typ.) + 1.0V] Parameters Sym. Min. Typ. Max. Units tSTART -- -- 5 ms VDD Low-to-High tDELAY -- -- 1 ms VBAT < VPTH to VBAT > VPTH Current Rise Time Out of Preconditioning tRISE -- -- 1 ms IOUT Rising to 90% of IREG Fast Charge Safety Timer Period tFAST 1.1 1.5 1.9 Hours CTIMER = 0.1 F tPRECON 45 60 75 Minutes CTIMER = 0.1 F tTERM 2.2 3 3.8 Hours CTIMER = 0.1 F Status Output turn-off tOFF -- -- 200 s ISINK = 1 mA to 0 mA Status Output turn-on tON -- -- 200 s ISINK = 0 mA to 1 mA UVLO Start Delay Conditions Current Regulation Transition Time Out of Preconditioning Preconditioning Current Regulation Preconditioning Charge Safety Timer Period Charge Termination Elapsed Time Termination Period Status Indicators TEMPERATURE SPECIFICATIONS Electrical Specifications: Unless otherwise indicated, all limits apply for VDD = [VREG (typ.) + 0.3V] to 12V. Typical values are at +25C, VDD = [VREG (typ.) + 1.0V] Parameters Sym. Min. Typ. Max. Units Specified Temperature Range TA -40 Operating Temperature Range TJ -40 Storage Temperature Range TA Thermal Resistance, 16-lead, 4 mm x 4 mm QFN Thermal Resistance, 16-lead SOIC Conditions -- +85 C -- +125 C -65 -- +150 C JA -- 47 -- C/W 4-Layer JC51-7 Standard Board, Natural Convection JA -- 86.1 -- C/W 4-Layer JC51-7 Standard Board, Natural Convection Temperature Ranges Thermal Package Resistances DS21893F-page 6 2004-2013 Microchip Technology Inc. MCP73861/2/3/4 2.0 TYPICAL PERFORMANCE CURVES Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. 4.207 MCP73861/3 VSET = VDD VDD = 5.2V 4.205 4.203 4.201 4.199 4.197 4.195 1.00 Supply Current (mA) Battery Regulation Voltage (V) NOTE: Unless otherwise indicated, VDD = [VREG(typ.) + 1V], IOUT = 10 mA and TA= +25C, Constant-voltage mode. MCP73861/3 VSET = VDD VDD = 5.2V 0.90 0.80 0.70 0.60 0.50 0.40 4.193 10 100 10 1000 100 Charge Current (mA) Charge Current (mA) MCP73861/3 VSET = VDD IOUT = 1000 mA 4.30 4.20 4.10 4.00 3.90 FIGURE 2-4: Supply Current (ISS) vs. Charge Current (IOUT). 1.60 Supply Current (mA) Battery Regulation Voltage (V) FIGURE 2-1: Battery Regulation Voltage (VBAT) vs. Charge Current (IOUT). 4.40 MCP73861/3 VSET = VDD IOUT = 1000 mA 1.40 1.20 1.00 0.80 0.60 0.40 3.80 4.5 6.0 7.5 9.0 10.5 4.5 12.0 6.0 FIGURE 2-2: Battery Regulation Voltage (VBAT) vs. Supply Voltage (VDD). 4.205 4.203 9.0 10.5 12.0 FIGURE 2-5: Supply Current (ISS) vs. Supply Voltage (VDD). 1.00 MCP73861/3 VSET = VDD IOUT = 10 mA Supply Current (mA) 4.207 7.5 Supply Voltage (V) Supply Voltage (V) Battery Regulation Voltage (V) 1000 4.201 4.199 4.197 4.195 MCP73861/3 VSET = VDD IOUT = 10 mA 0.90 0.80 0.70 0.60 0.50 0.40 4.193 4.5 6.0 7.5 9.0 10.5 12.0 Supply Voltage (V) FIGURE 2-3: Battery Regulation Voltage (VBAT) vs. Supply Voltage (VDD). 2004-2013 Microchip Technology Inc. 4.5 6.0 7.5 9.0 10.5 12.0 Supply Voltage (V) FIGURE 2-6: Supply Current (ISS) vs. Supply Voltage (VDD). DS21893F-page 7 MCP73861/2/3/4 +85C 0.30 +25C 0.25 0.20 -40C 0.15 0.10 0.05 MCP73861/3 VSET = VDD IOUT = 10 mA 1.40 1.20 1.00 0.80 0.60 100 125 150 175 200 Therm. Bias Current (A) FIGURE 2-9: Thermistor Reference Voltage (VTHREF) vs. Thermistor Bias Current (ITHREF). DS21893F-page 8 80 70 60 50 40 80 70 60 2.500 80 75 70 50 60 25 50 2.500 2.505 40 2.505 2.510 -20 2.510 2.515 MCP73861/3 VSET = VDD ITHREF = 100 A -30 2.515 2.520 -40 MCP73861/3 VSET = VDD 0 FIGURE 2-11: Battery Regulation Voltage (VBAT) vs. Ambient Temperature (TA). Therm. Reference Voltage (V) Therm. Reference Voltage (V) 2.520 50 Ambient Temperature (C) Supply Voltage (V) FIGURE 2-8: Thermistor Reference Voltage (VTHREF) vs. Supply Voltage (VDD). 40 4.193 12.0 30 10.5 20 9.0 4.195 30 7.5 4.197 10 6.0 4.199 20 2.500 4.201 10 2.510 4.203 -20 2.520 MCP73861/3 VSET = VDD IOUT = 10 mA 4.205 -30 2.530 4.207 -40 MCP73861/3 VSET = VDD ITHREF = 100 A 4.5 FIGURE 2-10: Supply Current (ISS) vs. Ambient Temperature (TA). Battery Regulation Voltage (V) Therm. Reference Voltage (V) FIGURE 2-7: Output Leakage Current (IDISCHARGE) vs. Battery Regulation Voltage (VBAT). 2.540 30 Ambient Temperature (C) Battery Regulation Voltage (V) 2.550 20 4.4 0 4.0 10 3.6 0 3.2 0 2.8 -10 2.4 -40 2.0 -10 0.40 0.00 -10 0.35 1.60 MCP73861/3 VSET = VDD VDD = VSS -20 0.40 -30 0.45 Supply Current (mA) Output Leakage Current (A) NOTE: Unless otherwise indicated, VDD = [VREG(typ.) + 1V], IOUT = 10 mA and TA= +25C, Constant-voltage mode. Ambient Temperature (C) FIGURE 2-12: Thermistor Reference Voltage (VTHREF) vs. Ambient Temperature (TA). 2004-2013 Microchip Technology Inc. MCP73861/2/3/4 8.407 1.00 MCP73862/4 VSET = VDD VDD = 9.4V 8.405 8.403 Supply Current (mA) Battery Regulation Voltage (V) NOTE: Unless otherwise indicated, VDD = [VREG(typ.) + 1V], IOUT = 10 mA and TA= +25C, Constant-voltage mode. 8.401 8.399 8.397 8.395 0.90 MCP73862/4 VSET = VDD VDD = 9.4V 0.80 0.70 0.60 0.50 0.40 8.393 10 100 10 1000 100 Charge Current (mA) Charge Current (mA) FIGURE 2-16: Supply Current (ISS) vs. Charge Current (IOUT). 8.407 8.403 8.401 1.60 Supply Current (mA) Battery Regulation Voltage (V) FIGURE 2-13: Battery Regulation Voltage (VBAT) vs. Charge Current (IOUT). 8.405 MCP73862/4 VSET = VDD IOUT = 1000 mA 8.399 8.397 8.395 8.393 10.0 1.40 MCP73862/4 VSET = VDD IOUT = 1000 mA 1.20 1.00 0.80 0.60 0.40 10.4 10.8 11.2 11.6 12.0 9.0 9.5 Supply Voltage (V) 10.5 11.0 11.5 12.0 FIGURE 2-17: Supply Current (ISS) vs. Supply Voltage (VDD). 1.00 MCP73862/4 VSET = VDD IOUT = 10 mA Supply Current (mA) Battery Regulation Voltage (V) 8.410 10.0 Supply Voltage (V) FIGURE 2-14: Battery Regulation Voltage (VBAT) vs. Supply Voltage (VDD). 8.412 1000 8.408 8.406 8.404 8.402 8.400 0.90 MCP73862/4 VSET = VDD IOUT = 10 mA 0.80 0.70 0.60 0.50 0.40 8.398 9.0 9.5 10.0 10.5 11.0 11.5 12.0 Supply Voltage (V) FIGURE 2-15: Battery Regulation Voltage (VBAT) vs. Supply Voltage (VDD). 2004-2013 Microchip Technology Inc. 9.0 9.5 10.0 10.5 11.0 11.5 12.0 Supply Voltage (V) FIGURE 2-18: Supply Current (ISS) vs. Supply Voltage (VDD). DS21893F-page 9 MCP73861/2/3/4 0.45 1.60 MCP73862/4 VSET = VDD VDD = VSS 0.40 0.35 +85C 0.30 +25C 0.25 0.20 -40C 0.15 0.10 0.05 Supply Current (mA) MCP73862/4 VSET = VDD IOUT = 10 mA 1.40 1.20 1.00 0.80 0.60 75 100 125 150 175 200 Thermistor Bias Current (A) FIGURE 2-21: Thermistor Reference Voltage (VTHREF) vs. Thermistor Bias Current (ITHREF). DS21893F-page 10 80 70 60 50 40 80 70 60 50 40 2.530 80 50 70 25 60 0 2.534 50 2.540 2.538 40 2.542 2.542 -20 2.544 MCP73862/4 VSET = VDD ITHREF = 100 A 2.546 -30 2.546 2.550 -40 MCP73862/4 VSET = VDD 2.548 FIGURE 2-23: Battery Regulation Voltage (VBAT) vs. Ambient Temperature (TA). Therm. Reference Voltage (V) Therm. Reference Voltage (V) 2.550 30 Ambient Temperature (C) Supply Voltage (V) FIGURE 2-20: Thermistor Reference Voltage (VTHREF) vs. Supply Voltage (VDD). 30 8.386 12.0 30 11.5 20 11.0 8.390 10 10.5 8.394 20 10.0 8.398 10 9.5 8.402 0 2.530 8.406 0 2.540 MCP73862/4 VSET = VDD IOUT = 10 mA 8.410 -30 2.550 8.414 -40 MCP73862/4 VSET = VDD ITHREF = 100 A 9.0 FIGURE 2-22: Supply Current (ISS) vs. Ambient Temperature (TA). Battery Regulation Voltage (V) Therm. Reference Voltage (V) FIGURE 2-19: Output Leakage Current (IDISCHARGE) vs. Battery Regulation Voltage (VBAT). 2.560 20 Ambient Temperature (C) Battery Regulation Voltage (V) 2.570 0 8.8 10 8.0 -10 7.2 -10 6.4 -10 5.6 -20 4.8 -20 4.0 -30 0.40 0.00 -40 Output Leakage Current (A) NOTE: Unless otherwise indicated, VDD = [VREG(typ.) + 1V], IOUT = 10 mA and TA= +25C, Constant-voltage mode. Ambient Temperature (C) FIGURE 2-24: Thermistor Reference Voltage (VTHREF) vs. Ambient Temperature (TA). 2004-2013 Microchip Technology Inc. MCP73861/2/3/4 NOTE: Unless otherwise indicated, VDD = [VREG(typ.) + 1V], IOUT = 10 mA and TA= +25C, Constant-voltage mode. VDD VDD VBAT VBAT MCP73861 VDD Stepped from 5.2V to 6.2V IOUT = 500 mA COUT = 10 F, X7R, Ceramic MCP73861 VDD Stepped from 5.2V to 6.2V IOUT = 10 mA COUT = 10 F, X7R, Ceramic FIGURE 2-25: Line Transient Response. MCP73861 VDD 5.2V COUT = 10 F, X7R, Ceramic FIGURE 2-28: MCP73861 VDD 5.2V COUT = 10 F, X7R, Ceramic VBAT 100 mA Line Transient Response. IOUT 500 mA 10 mA FIGURE 2-26: Attenuation (dB) -10 -20 -30 Load Transient Response. FIGURE 2-29: -10 -40 -50 -60 -20 -30 -40 MCP73861 VDD = 5.2V VAC = 100 mVp-p IOUT = 100 mA COUT = 10 F, X7R, Ceramic -50 -60 -70 -70 0.1 1 10 100 1000 -80 0.01 Power Supply Ripple 2004-2013 Microchip Technology Inc. 0.1 1 10 100 1000 Frequency (kHz) Frequency (kHz) FIGURE 2-27: Rejection. Load Transient Response. 0 MCP73861 VDD = 5.2V VAC = 100 mVp-p IOUT = 10 mA COUT = 10 F, Ceramic -80 0.01 IOUT 10 mA Attenuation (dB) 0 VBAT FIGURE 2-30: Rejection. Power Supply Ripple DS21893F-page 11 MCP73861/2/3/4 NOTE: Unless otherwise indicated, VDD = [VREG(typ.) + 1V], IOUT = 10 mA and TA= +25C, Constant-voltage mode. 800 600 400 200 501 499 497 495 FIGURE 2-31: Charge Current (IOUT) vs. Programming Resistor (RPROG). 80 70 60 50 40 0 30 0 20 536 10 1.6k -10 4.8k -20 493 Programming Resistor () DS21893F-page 12 MCP73861/2/3/4 VSET = VDD RPROG = 1.6 k -30 0 OPEN 503 -40 1000 505 MCP73861/2/3/4 VSET = VDD Charge Current (mA) Charge Current (mA) 1200 Ambient Temperature (C) FIGURE 2-32: Charge Current (IOUT) vs. Ambient Temperature (TA). 2004-2013 Microchip Technology Inc. MCP73861/2/3/4 3.0 PIN DESCRIPTION The descriptions of the pins are listed in Table 3.1. TABLE 3-1: PIN FUNCTION TABLE MCP73861/2/3/4 QFN 3.1 SOIC Symbol Function 1 3 VSET Voltage Regulation Selection 2 4 VDD1 Battery Management Input Supply 3 5 VDD2 Battery Management Input Supply 4 6 VSS1 Battery Management 0V Reference 5 7 PROG Current Regulation Set 6 8 THREF Cell Temperature Sensor Bias 7 9 THERM Cell Temperature Sensor Input 8 10 TIMER Timer Set 9 11 VSS3 Battery Management 0V Reference 10 12 VBAT1 Battery Charge Control Output 11 13 VBAT2 Battery Charge Control Output 12 14 VBAT3 Battery Voltage Sense 13 15 VSS2 Battery Management 0V Reference 14 16 EN 15 1 STAT2 Fault Status Output 16 2 STAT1 Charge Status Output 17 - EP Logic Enable Exposed Pad; Battery Management 0V Reference Voltage Regulation Selection (VSET) MCP73861/3: Connect VSET to VSS for 4.1V regulation voltage, connect to VDD for 4.2V regulation voltage. MCP73862/4: Connect VSET to VSS for 8.2V regulation voltage, connect to VDD for 8.4V regulation voltage. 3.2 Battery Management Input Supply (VDD2, VDD1) A supply voltage of [VREG (typ.) + 0.3V] to 12V is recommended. Bypass to VSS with a minimum of 4.7 F. A 1.5 k resistor should be connected from VDD to ground when using disconnectable supplies to force VDD < VBAT when the supply is disconnected and assure low leakage current. 3.3 Battery Management 0V Reference (VSS1, VSS2, VSS3) Connect to negative terminal of battery and input supply. 3.4 Current Regulation Set (PROG) Preconditioning, fast and termination currents are scaled by placing a resistor from PROG to VSS. 2004-2013 Microchip Technology Inc. 3.5 Cell Temperature Sensor Bias (THREF) THREF is a voltage reference to bias external thermistor for continuous cell temperature monitoring and prequalification. 3.6 Cell Temperature Sensor Input (THERM) THERM is an input for an external thermistor for continuous cell-temperature monitoring and prequalification. Connect to THREF/3 to disable temperature sensing. 3.7 Timer Set All safety timers are scaled by CTIMER/0.1 F. 3.8 Battery Charge Control Output (VBAT1, VBAT2) Connect to positive terminal of battery. Drain terminal of internal P-channel MOSFET pass transistor. Bypass to VSS with a minimum of 4.7 F to ensure loop stability when the battery is disconnected. 3.9 Battery Voltage Sense (VBAT3) VBAT3 is a voltage sense input. Connect to positive terminal of battery. A precision internal resistor divider regulates the final voltage on this pin to VREG. DS21893F-page 13 MCP73861/2/3/4 3.10 Logic Enable (EN) EN is an input to force charge termination, initiate charge, clear faults or disable automatic recharge. 3.11 Fault Status Output (STAT2) STAT2 is a current-limited, open-drain drive for direct connection to a LED for charge status indication. Alternatively, a pull-up resistor can be applied for interfacing to a host microcontroller. 3.12 Charge Status Output (STAT1) STAT1 is a current-limited, open-drain drive for direct connection to a LED for charge status indication. Alternatively, a pull-up resistor can be applied for interfacing to a host microcontroller. 3.13 Exposed Pad (EP) There is an internal electrical connection between the exposed thermal pad and VSS. The EP must be connected to the same potential as the VSS pin on the Printed Circuit Board (PCB). DS21893F-page 14 2004-2013 Microchip Technology Inc. MCP73861/2/3/4 DEVICE OVERVIEW The MCP7386X family of devices are highly advanced linear charge management controllers. Refer to the functional block diagram. Figure 4-2 depicts the operational flow algorithm from charge initiation to completion and automatic recharge. 4.1 Charge Qualification and Preconditioning Upon insertion of a battery, or application of an external supply, the MCP7386X family of devices automatically performs a series of safety checks to qualify the charge. The input source voltage must be above the Undervoltage Lockout (UVLO) threshold, the enable pin must be above the logic-high level and the cell temperature must be within the upper and lower thresholds. The qualification parameters are continuously monitored. Deviation beyond the limits automatically suspends or terminates the charge cycle. The input voltage must deviate below the UVLO stop threshold for at least one clock period to be considered valid. Once the qualification parameters have been met, the MCP7386X initiates a charge cycle. The charge status output is pulled low throughout the charge cycle (see Table 5-1 for charge status outputs). If the battery voltage is below the preconditioning threshold (VPTH), the MCP7386X preconditions the battery with a trickle-charge. The preconditioning current is set to approximately 10% of the fast charge regulation current. The preconditioning trickle-charge safely replenishes deeply depleted cells and minimizes heat dissipation during the initial charge cycle. If the battery voltage has not exceeded the preconditioning threshold before the preconditioning timer has expired, a fault is indicated and the charge cycle is terminated. 4.2 Constant Current Regulation - Fast Charge Preconditioning ends, and fast charging begins, when the battery voltage exceeds the preconditioning threshold. Fast charge regulates to a constant current (IREG), which is set via an external resistor connected to the PROG pin. Fast charge continues until the battery voltage reaches the regulation voltage (VREG), or the fast charge timer expires; in which case, a fault is indicated and the charge cycle is terminated. 4.3 Constant Voltage Regulation When the battery voltage reaches the regulation voltage (VREG), constant voltage regulation begins. The MCP7386X monitors the battery voltage at the VBAT pin. This input is tied directly to the positive terminal of the battery. 2004-2013 Microchip Technology Inc. The MCP7386X selects the voltage regulation value based on the state of VSET. With VSET tied to VSS, the MCP73861/3 and MCP73862/4 regulate to 4.1V and 8.2V, respectively. With VSET tied to VDD, the MCP73861/3 and MCP73862/4 regulate to 4.2V and 8.4V, respectively. 4.4 Charge Cycle Completion and Automatic Re-Charge The MCP7386X monitors the charging current during the Constant-voltage regulation mode. The charge cycle is considered complete when the charge current has diminished below approximately 8% of the regulation current (IREG), or the elapsed timer has expired. The MCP7386X automatically begins a new charge cycle when the battery voltage falls below the recharge threshold (VRTH), assuming all the qualification parameters are met. 4.5 Thermal Regulation The MCP7386X family limits the charge current based on the die temperature. Thermal regulation optimizes the charge cycle time while maintaining device reliability. If thermal regulation is entered, the timer is automatically slowed down to ensure that a charge cycle will not terminate prematurely. Figure 4-1 depicts the thermal regulation profile. 1400 Maximum Charge Current (mA) 4.0 1200 1000 800 Maximum Minimum 600 400 200 0 0 20 40 60 80 100 120 140 Die Temperature ( C) FIGURE 4-1: Typical Maximum Charge Current vs. Die Temperature. 4.6 Thermal Shutdown The MCP7386X family suspends charge if the die temperature exceeds 155C. Charging will resume when the die temperature has cooled by approximately 10C. The thermal shutdown is a secondary safety feature in the event that there is a failure within the thermal regulation circuitry. DS21893F-page 15 FIGURE 4-2: DS21893F-page 16 Yes Yes Yes VDD < VUVLO or EN Low Yes Yes Note 2 Note 1 Note 1 No STAT1 = Off STAT2 = On Fault Charge Current = 0 Reset Safety Timer No Yes STAT1 = Off STAT2 = Flashing Safety Timer Suspended Charge Current = 0 Temperature OK No Safety Timer Expired No VBAT > VPTH No The charge current will be scaled based on the die temperature during thermal regulation. Refer to Section 4.5, "Thermal Regulation", for details. Note 2: Preconditioning Mode Charge Current = IPREG Reset Safety Timer The qualification parameters are continuously monitored throughout the charge cycle. Refer to Section 4.1, "Charge Qualification and Preconditioning", for details. Note 1: Yes Yes STAT1 = On STAT2 = Off Yes Yes VDD < VUVLO VBAT < VRTH or EN Low No STAT1 = Flashing (MCP73861/2) STAT1 = Off (MCP73863/4) STAT2 = Off (All Devices) Charge Termination Charge Current = 0 Reset Safety Timer No STAT1 = Flashing Safety Timer Suspended Charge Current = 0 Temperature OK No IOUT < ITERM Elapsed Timer Expired Constant-Voltage Mode Output Voltage = VREG No STAT1 = Off STAT2 = Flashing Charge Current = 0 No STAT1 = Off STAT2 = Off No STAT1 = Off STAT2 = Flashing Safety Timer Suspended Charge Current = 0 Temperature OK No Safety Timer Expired No VBAT = VREG Constant-Current Mode Charge Current = IREG Reset Safety Timer Yes VBAT > VPTH Yes Temperature OK Yes VDD > VUVLO EN High Initialize MCP73861/2/3/4 Operational Flow Algorithm. 2004-2013 Microchip Technology Inc. MCP73861/2/3/4 5.0 DETAILED DESCRIPTION 5.1 Analog Circuitry 5.1.1 BATTERY MANAGEMENT INPUT SUPPLY (VDD1, VDD2) The VDD input is the input supply to the MCP7386X. The MCP7386X automatically enters a Power-down mode if the voltage on the VDD input falls below the UVLO voltage (VSTOP). This feature prevents draining the battery pack when the VDD supply is not present. The VDD inputs should be tied to ground with a resistor <= 1.5 k to prevent VDD from floating and staying at VBAT level if the input supply is disconnected. The resistor will assure that VDD < VBAT when the input supply is removed. 5.1.2 13.2 - 11 I REG R PROG = ---------------------------------------12 IREG - 1.2 Where: IREG = the desired fast charge current in amps. RPROG = measured in k The preconditioning trickle-charge current and the charge termination current are scaled to approximately 10% and 8% of IREG, respectively. CELL TEMPERATURE SENSOR BIAS (THREF) A 2.5V voltage reference is provided to bias an external thermistor for continuous cell temperature monitoring and prequalification. A ratio metric window comparison is performed at threshold levels of VTHREF/2 and VTHREF/4. 5.1.4 Figure 6-1 depicts a typical application circuit with connection of the THERM input. The resistor values of RT1 and RT2 are calculated with the following equations. For NTC thermistors: 2 R COLD R HOT R T1 = ---------------------------------------------RCOLD - R HOT 2 R COLD R HOT R T2 = ---------------------------------------------RCOLD - 3 R HOT For PTC thermistors: 2 R COLD RHOT R T1 = ---------------------------------------------RHOT - RCOLD PROG INPUT Fast charge current regulation can be scaled by placing a programming resistor (RPROG) from the PROG input to VSS. Connecting the PROG input to VSS allows for a maximum fast charge current of 1.2A, typically. The minimum fast charge current is 100 mA, set by letting the PROG input float. The following formula calculates the value for RPROG: 5.1.3 temperature-sensing circuit is removed from the system when VDD is not applied, eliminating additional discharge of the battery pack. CELL TEMPERATURE SENSOR INPUT (THERM) The MCP73861/2/3/4 continuously monitors temperature by comparing the voltage between the THERM input and VSS with the upper and lower temperature thresholds. A negative or positive temperature coefficient, NTC or PTC thermistor and an external voltagedivider typically develop this voltage. The temperature sensing circuit has its own reference to which it performs a ratio metric comparison. Therefore, it is immune to fluctuations in the supply input (VDD). The 2004-2013 Microchip Technology Inc. 2 R COLD RHOT R T2 = ---------------------------------------------RHOT - 3 RCOLD Where: RCOLD and RHOT are the thermistor resistance values at the temperature window of interest. Applying a voltage equal to VTHREF/3 to the THERM input disables temperature monitoring. 5.1.5 TIMER SET INPUT (TIMER) The TIMER input programs the period of the safety timers by placing a timing capacitor (CTIMER) between the TIMER input pin and VSS. Three safety timers are programmed via the timing capacitor. The preconditioning safety timer period: C TIMER t PRECON = ------------------- 1.0Hour s 0.1 F The fast charge safety timer period: CTIMER t FAST = ------------------- 1.5Hours 0.1 F The elapsed time termination period: C TIMER t TERM = ------------------- 3.0Hours 0.1 F The preconditioning timer starts after qualification and resets when the charge cycle transitions to the fast charge, Constant-current mode. The fast charge timer and the elapsed timer start once the MCP7386X transitions from preconditioning. The fast charge timer resets when the charge cycle transitions to the Constant-voltage mode. The elapsed timer will expire and terminate the charge if the sensed current does not diminish below the termination threshold. DS21893F-page 17 MCP73861/2/3/4 During thermal regulation, the timer is slowed down proportional to the charge current. 5.1.6 BATTERY VOLTAGE SENSE (VBAT3) The MCP7386X monitors the battery voltage at the VBAT3 pin. This input is tied directly to the positive terminal of the battery pack. 5.1.7 BATTERY CHARGE CONTROL OUTPUT (VBAT1, VBAT2) The battery charge control output is the drain terminal of an internal P-channel MOSFET. The MCP7386X provides constant current and voltage regulation to the battery pack by controlling this MOSFET in the linear region. The battery charge control output should be connected to the positive terminal of the battery pack. 5.2 5.2.1 Digital Circuitry Two status outputs provide information on the state of charge. The current-limited, open-drain outputs can be used to illuminate external LEDs. Optionally, a pull-up resistor can be used on the output for communication with a host microcontroller. Table 5-1 summarizes the state of the status outputs during a charge cycle. STATUS OUTPUTS CHARGE CYCLE STAT1 STAT1 STAT2 Qualification Off Off Preconditioning On Off Constant-Current Fast Charge On Off Constant-Voltage On Off Charge Complete Flashing (1 Hz, 50% duty cycle) (MCP73861/2) Off (MCP73863/4) During a Fault condition, the STAT1 status output will be off and the STAT2 status output will be on. To recover from a Fault condition, the input voltage must be removed and then reapplied, or the enable input (EN) must be de-asserted to a logic-low, then asserted to a logic-high. When the voltage on the THERM input is outside the preset window, the charge cycle will not start, or will be suspended. The charge cycle is not terminated and recovery is automatic. The charge cycle will resume (or start) once the THERM input is valid and all other qualification parameters are met. During an invalid THERM condition, the STAT1 status output will be off and the STAT2 status output will flash. 5.2.2 CHARGE STATUS OUTPUTS (STAT1, STAT2) TABLE 5-1: The flashing rate (1 Hz) is based off a timer capacitor (CTIMER) of 0.1 F. The rate will vary based on the value of the timer capacitor. VSET INPUT The VSET input selects the regulated output voltage of the MCP7386X. With VSET tied to VSS, the MCP73861/ 3 and MCP73862/4 regulate to 4.1V and 8.2V, respectively. With VSET tied to VDD, the MCP73861/3 and MCP73862/4 regulate to 4.2V and 8.4V, respectively. 5.2.3 LOGIC ENABLE (EN) The logic enable input pin (EN) can be used to terminate a charge at any time during the charge cycle, as well as to initiate a charge cycle or initiate a recharge cycle. Applying a logic-high input signal to the EN pin, or tying it to the input source, enables the device. Applying a logic-low input signal disables the device and terminates a charge cycle. When disabled, the device's supply current is reduced to 0.17 A, typically. Off (All Devices) Fault Off On THERM Invalid Off Flashing (1 Hz 50% duty cycle) Disabled - Sleep mode Off Off Input Voltage Disconnected (1.5K Pulldown) Off Off Legend: Off state: Open-drain is high-impedance On state: Open-drain can sink current typically 7 mA Flashing: Toggles between off state and on state DS21893F-page 18 2004-2013 Microchip Technology Inc. MCP73861/2/3/4 6.0 APPLICATIONS Figure 6-1 illustrates a typical stand-alone application circuit, while Figures 6-2 and 6-3 illustrate the accompanying charge profile The MCP7386X is designed to operate in conjunction with a host microcontroller or in stand-alone applications. The MCP7386X provides the preferred charge algorithm for Lithium-Ion and Lithium-Polymer cells Constant-current followed by Constant-voltage. . STAT1 16 15 EN VSS2 14 13 VSET 1 12 VBAT3 VDD1 2 11 VBAT2 VDD2 3 10 VBAT1 VSS1 4 9 VSS3 MCP73861 6 THREF 5 PROG RPROG 7 + Single Lithium-Ion - Cell 8 TIMER CTIMER THERM Unregulated Wall Cube STAT2 1.5K RT1 RT2 FIGURE 6-1: Typical Application Circuit. Preconditioning Mode Constant-Current Mode Constant-Voltage Mode Regulation Voltage (VREG) Regulation Current (IREG) Charge Voltage Transition Threshold (VPTH) Precondition Current (IPREG) Charge Current Termination Current (ITERM) Precondition Safety Timer Fast Charge Safety Timer Elapsed Time Termination Timer FIGURE 6-2: Typical Charge Profile. 2004-2013 Microchip Technology Inc. DS21893F-page 19 MCP73861/2/3/4 Preconditioning Mode Constant-Current Mode Constant-Voltage Mode Regulation Voltage (VREG) Regulation Current (IREG) Charge Voltage Transition Threshold (VPTH) Precondition Current (IPREG) Termination Current (ITERM) Charge Current Precondition Safety Timer Fast Charge Safety Timer Elapsed Time Termination Timer FIGURE 6-3: 6.1 Typical Charge Profile in Thermal Regulation. Application Circuit Design Due to the low efficiency of linear charging, the most important factors are thermal design and cost, which are a direct function of the input voltage, output current and thermal impedance between the battery charger and the ambient cooling air. The worst-case situation is when the device has transitioned from the Preconditioning mode to the Constant-current mode. In this situation, the battery charger has to dissipate the maximum power. A trade-off must be made between the charge current, cost and thermal requirements of the charger. 6.1.1 COMPONENT SELECTION Selection of the external components in Figure 6-1 is crucial to the integrity and reliability of the charging system. The following discussion is intended as a guide for the component selection process. 6.1.1.1 Current Programming Resistor (RPROG) 1200 mA is the maximum charge current obtainable from the MCP7386X. For this situation, the PROG input should be connected directly to VSS. 6.1.1.2 Thermal Considerations The worst-case power dissipation in the battery charger occurs when the input voltage is at the maximum and the device has transitioned from the Preconditioning mode to the Constant-current mode. In this case, the power dissipation is: PowerDissipation = V DDMAX - V PTHMIN IREGMAX Where: VDDMAX = the maximum input voltage IREGMAX = the maximum fast charge current VPTHMIN = the minimum transition threshold voltage The preferred fast charge current for Lithium-Ion cells is at the 1C rate, with an absolute maximum current at the 2C rate. For example, a 500 mAh battery pack has a preferred fast charge current of 500 mA. Charging at this rate provides the shortest charge cycle times without degradation to the battery pack performance or life. DS21893F-page 20 2004-2013 Microchip Technology Inc. MCP73861/2/3/4 Power dissipation with a 5V, 10% input voltage source is: PowerDissipation = 5.5V - 2.7V 575mA = 1.61W With the battery charger mounted on a 1 in2 pad of 1 oz. copper, the junction temperature rise is 60C, approximately. This would allow for a maximum operating ambient temperature of 50C before thermal regulation is entered. 6.1.1.3 6.2 PCB Layout Issues For optimum voltage regulation, place the battery pack as close as possible to the device's VBAT and VSS pins, recommended to minimize voltage drops along the high current-carrying PCB traces. If the PCB layout is used as a heatsink, adding many vias in the heatsink pad can help conduct more heat to the backplane of the PCB, thus reducing the maximum junction temperature. External Capacitors The MCP7386X is stable with or without a battery load. In order to maintain good AC stability in the Constantvoltage mode, a minimum capacitance of 4.7 F is recommended to bypass the VBAT pin to VSS. This capacitance provides compensation when there is no battery load. In addition, the battery and interconnections appear inductive at high frequencies. These elements are in the control feedback loop during Constant-voltage mode. Therefore, the bypass capacitance may be necessary to compensate for the inductive nature of the battery pack. Virtually any good quality output filter capacitor can be used, independent of the capacitor's minimum Effective Series Resistance (ESR) value. The actual value of the capacitor (and its associated ESR) depends on the output load current. A 4.7 F ceramic, tantalum or aluminum electrolytic capacitor at the output is usually sufficient to ensure stability for up to a 1A output current. 6.1.1.4 Reverse-Blocking Protection The MCP7386X provides protection from a faulted or shorted input, or from a reversed-polarity input source. Without the protection, a faulted or shorted input would discharge the battery pack through the body diode of the internal pass transistor. 6.1.1.5 Enable Interface In the stand-alone configuration, the enable pin is generally tied to the input voltage. The MCP7386X automatically enters a Low-power mode when voltage on the VDD input falls below the UVLO voltage (VSTOP), reducing the battery drain current to 0.23 A,typically. 6.1.1.6 Charge Status Interface Two status outputs provide information on the state of charge. The current-limited, open-drain outputs can be used to illuminate external LEDs. Refer to Table 5-1 for a summary of the state of the status outputs during a charge cycle. 2004-2013 Microchip Technology Inc. DS21893F-page 21 MCP73861/2/3/4 NOTES: DS21893F-page 22 2004-2013 Microchip Technology Inc. MCP73861/2/3/4 7.0 PACKAGING INFORMATION 7.1 Package Marking Information Example: 16-Lead QFN 73861 XXXXX I/ML 1108 XXXXXX XXXXXX YWWNNN 256 16-Lead SOIC (150 mil) XXXXXXXXXXXXX XXXXXXXXXXXXX YYWWNNN Legend: XX...X Y YY WW NNN e3 * Note: Example: MCP73861 e3 I/SL^^ 1108256 Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. 2004-2013 Microchip Technology Inc. DS21893F-page 23 MCP73861/2/3/4 ' ! "" # $ %& )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ D2 D EXPOSED PAD e E2 E 2 2 1 1 b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page 24 2004-2013 Microchip Technology Inc. MCP73861/2/3/4 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2004-2013 Microchip Technology Inc. DS21893F-page 25 MCP73861/2/3/4 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS21893F-page 26 2004-2013 Microchip Technology Inc. MCP73861/2/3/4 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2004-2013 Microchip Technology Inc. DS21893F-page 27 MCP73861/2/3/4 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS21893F-page 28 2004-2013 Microchip Technology Inc. MCP73861/2/3/4 APPENDIX A: REVISION HISTORY Revision F (March 2013) The following is the list of modifications: 1. 2. 3. 4. Added the Output Reverse Leakage Switchover Time parameter to the DC Characteristics table. Updated Section 3.2. Updated Section 5.1.1. Updated Figure 6-1. Revision E (April 2011) The following is the list of modifications: 1. Updated Figure 2-4. Revision D (December 2008) The following is the list of modifications: 1. Updated package outline diagrams. Revision C (August 2005) The following is the list of modifications: 1. 2. 3. Added MCP73863 and MCP73864 devices throughout data sheet. Added Appendix A: Revision History. Updated QFN and SOIC package diagrams. Revision B (December 2004) The following is the list of modifications: Added SOIC package throughout data sheet. Revision A (June 2004) Original Release of this Document. 2004-2013 Microchip Technology Inc. DS21893F-page 29 MCP73861/2/3/4 NOTES: DS21893F-page 30 2004-2013 Microchip Technology Inc. MCP73861/2/3/4 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, contact the Microchip sales office. Device: PART NO. X /XX Device Temperature Range Package MCP73861: MCP73861T: MCP73862: MCP73862T: MCP73863: MCP73863T: MCP73864: MCP73864T: Temperature Range: I +85C a) b) Single-Cell Charge Controller with Temperature Monitor Single-Cell Charge Controller with Temperature Monitor, Tape and Reel Dual Series Cells Charge Controller with Temperature Monitor Dual Series Cells Charge Controller with Temperature Monitor, Tape and Reel Single-cell Charge Controller with Temperature Monitor Single-Cell Charge Controller with Temperature Monitor, Tape and Reel Dual Series Cells Charge Controller with Temperature Monitor Dual Series Cells Charge Controller with Temperature Monitor, Tape and Reel = -40C to Examples: c) d) a) b) c) d) ML SL = Plastic Quad Flat No Lead, 4x4 mm Body (QFN), 16-lead = Plastic Small Outline, 150 mm Body (SOIC), 16-lead b) c) d) a) b) c) d) 2004-2013 Microchip Technology Inc. Single-Cell Controller 16LD-QFN package. MCP73861T-I/ML: Tape and Reel, Single-Cell Controller 16LD-QFN package. MCP73861-I/SL: Single-Cell Controller 16LD-SOIC package. MCP73861T-I/SL: Tape and Reel, Single-Cell Controller 16LD-SOIC package. MCP73862-I/ML: Dual-Cell Controller 16LD-QFN package. MCP73862T-I/ML: Tape and Reel, Dual-Cell Controller 16LD-QFN package. MCP73862-I/SL: Dual-Cell Controller 16LD-SOIC package. MCP73862T-I/SL: Tape and Reel, Dual-Cell Controller 16LD-SOIC package. (Industrial) a) Package: MCP73861-I/ML: MCP73863-I/ML: Single-Cell Controller 16LD-QFN package. MCP73863T-I/ML: Tape and Reel, Single-Cell Controller 16LD-QFN package. MCP73863-I/SL: Single-Cell Controller 16LD-SOIC package. MCP73863T-I/SL: Tape and Reel, Single-Cell Controller 16LD-SOIC package. MCP73864-I/ML: Dual-Cell Controller 16LD-QFN package. MCP73864T-I/ML: Tape and Reel, Dual-Cell Controller 16LD-QFN package. MCP73864-I/SL: Dual-Cell Controller 16LD-SOIC package. MCP73864T-I/SL: Tape and Reel, Dual-Cell Controller 16LD-SOIC package. DS21893F-page 31 MCP73861/2/3/4 NOTES: DS21893F-page 32 2004-2013 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: * Microchip products meet the specification contained in their particular Microchip Data Sheet. * Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. * There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. * Microchip is willing to work with the customer who is concerned about the integrity of their code. * Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MTP, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. Analog-for-the-Digital Age, Application Maestro, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O, Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA and Z-Scale are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. GestIC and ULPP are registered trademarks of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. (c) 2004-2013, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 9781620770405 QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV == ISO/TS 16949 == 2004-2013 Microchip Technology Inc. Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company's quality system processes and procedures are for its PIC(R) MCUs and dsPIC(R) DSCs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. DS21893F-page 33 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Osaka Tel: 81-6-6152-7160 Fax: 81-6-6152-9310 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 China - Hangzhou Tel: 86-571-2819-3187 Fax: 86-571-2819-3189 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Hong Kong SAR Tel: 852-2943-5100 Fax: 852-2401-3431 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 China - Shenzhen Tel: 86-755-8864-2200 Fax: 86-755-8203-1760 Taiwan - Kaohsiung Tel: 886-7-213-7828 Fax: 886-7-330-9305 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Taipei Tel: 886-2-2508-8600 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 DS21893F-page 34 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Japan - Tokyo Tel: 81-3-6880- 3770 Fax: 81-3-6880-3771 11/29/12 2004-2013 Microchip Technology Inc.