Overview
The P1010RDB is a highly integrated reference design board that can help
shorten your time to market. The reference design is aimed at low-cost networking
applications (with or without trust architecture), wired and wireless access, as well as
industrial and smart energy applications.
This cost-effective board is based on the QorIQ P1010 processor family and contains
leading-edge external components to help you quickly design and implement your
target application. The P1010RDB leverages the P1010 processor and supports
both the full-featured P1010 as well as the more cost-efficient P1014 device.
P1010RDB System Block Diagram
QorIQ
P1010/
P1014
6-Lane
SerDes
eTSEC1
1588
DDR3
(1 GB)
EEPROM RTC
JTAG COP
SD/MMC
USB-to-UART
POR Config Reset
CPLD
PowerClocking
NAND
Flash (2 GB)
NOR
Flash (32 MB)
SGMII PHY RJ-45
Header
Header
Header
SPI
Relay
DUAL
SLIC
Type A
RJ-11
RJ-11
FXO
FXS
RJ-11
RJ-45
SGMII PHY
RGMII
x1
x1
x1
SPI
UTMI
x1
ESDHC
UART0
UART1
I2C
x1
x1
x32 bits
P1014:16 bits
iSATA
Micro-AB
iSATA
Mini-PCIe®
Mini-PCIe
CAN
PHY
FlexCAN
RJ-45
RGMII PHY
DAC VCXO
Header
P1014 not available
P1010RDB System Block Diagram
QorIQ Multicore Processor Development
QorIQ P1010/P1014
Reference Design Board
For more information, please visit freescale.com/QorIQ
Freescale, the Freescale logo, PowerQUICC and QorIQ are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat.
& Tm. Off. All other product or service names are the property of their respective owners. The Power Architecture and
Power.org word marks and the Power and Power.org logos and related marks are trademarks and service marks licensed
by Power.org. © 2011, 2013 Freescale Semiconductor, Inc.
Document Number: P1010RDBFS REV 1
The P1010 processor family is based on
the e500 core, built on Power Architecture®
technology, which has a core frequency
range of 533–1000 MHz, and supports a
32 KB instruction and L1 data cache and a
256 KB L2 cache. The P1010 also supports
a complete trust architecture environment,
CAN controllers for industrial applications,
three Gigabit Ethernet controllers with IEEE®
1588 V2 support, USB 2.0 plus PHY, two PCI
Express® 1.0a controllers, up to six SerDes
interfaces, 16/32-bit DDR3 and DDR3L (16-bit
mode supports ECC), SPI controller supporting
booting from SPI, serial flash memory, SD/
MMC card controller supporting booting from
flash cards and an integrated security engine.
The new P1010 family with built-in 45 nm
process technology provides high integration
for cost-efficient solutions and enables a
trust platform (through trust architecture) for
customers that want to preserve the hardware
or software integrity of their platforms.
The P1010RDB platform features 1 GB of
DDR3 SDRAM, 32 MB NOR flash and
32 MB NAND flash, and can boot securely
from either NOR or NAND flash memory.
Other boot options (i.e., SD/MMC, SPI) are
also supported. The platform supports three
Gigabit-capable ports via an SGMII or RGMII
PHYs, as well as a single-port USB and
associated PHY.
The P1010RDB also supports a PCI Express®
add-in connector and a MiniPCI Express
slot, as well as an SD/MMC card slot. These
components, integrated with the P1010 family,
provide an application-specific platform that
can help you get a jump start on your next
application design. In addition, the P1010RDB
provides a simplified migration path for
existing PowerQUICC or PowerQUICC Pro
processor customers wishing to migrate to
QorIQ multicore processors. Customers can
migrate to the single-core P1014 processor as
a stepping stone on their way to a full-featured
P1010 processor.
Since the P1010 product is pin-compatible
with the P1014, only one version of the board
is available with options on the board support
package to target either processor.
Along with the hardware support, the
P1010RDB comes with a board support
package (BSP) that includes both the U-boot
and Linux® 2.6 operating system support.
The platform is also available with third-party
software applications. For a demonstration or
for details of Freescale third-party applications
for this platform, please contact your local
Freescale sales office.
P1010RDB Board Features
Memory
• 1 GB DDR3 (8-bit x 4 chips), supports up
to 8 GB on-board DDR3 SDRAM
• 32 MB (16-bit) NOR flash memory
• 32 MB SLC NAND flash memory
• 256 KB I2C EEPROM
• 128 MB SPI flash
• SD/MMC connector to interface with the SD
memory card
PCI Express
• One standard PCI Express connector
• One mini PCI Express connector
SATA
• One internal SATA connected to 2.5” 160 G
SATA 2 HDD
• One eSATA connector to rear panel
USB 2.0
• One USB 2.0 port connected via UTMI PHY
to mini AB interface
• One USB 2.0 port directly connected to
mini AB interface
Three 10/100/1000 Ports
• eTSEC 1 connected to RGMII PHY
• eTSEC 2 and 3 connected to SGMII PHY
Flex CAN
• Two connectors for field bus interface
UART
• DUART interface, terminated as RJ45
connectors
TDM
• Two FXS ports connected via na external
SLIC to the TDM interface
• One FXO port connected via a relay to FXS
for switchover to POTS
Others
• LEDs: Power (green), link (green), activities
(yellow)
• JTAG for debugging
• IEEE 1588 V2 signals for test and
measurement
Form Factor
• Mini ITX form factor
