STGIPS20C60 SLLIMMTM small low-loss intelligent molded module IPM, 3-phase inverter - 20 A, 600 V short-circuit rugged IGBT Datasheet - production data Applications * 3-phase inverters for motor drives * Air conditioners Description This intelligent power module provides a compact, high performance AC motor drive in a simple, rugged design. Combining ST proprietary control ICs with the most advanced short-circuitrugged IGBT system technology, this device is ideal for 3-phase inverters in applications such as motor drives and air conditioners. SLLIMMTM is a trademark of STMicroelectronics. SDIP-25L Features * IPM 20 A, 600 V 3-phase IGBT inverter bridge including control ICs for gate driving and freewheeling diodes * Short-circuit rugged IGBTs * 3.3 V, 5 V, 15 V CMOS/TTL inputs comparators with hysteresis and pull down / pull up resistors * Undervoltage lockout * Internal bootstrap diode * Interlocking function * Smart shutdown function * Comparator for fault protection against over temperature and overcurrent * DBC leading to low thermal resistance * Isolation rating of 2500 Vrms/min * UL recognized: UL1557 file E81734 Table 1. Device summary Order code Marking Package Packing STGIPS20C60 GIPS20C60 SDIP-25L Tube March 2015 This is information on a product in full production. DocID024138 Rev 7 1/20 www.st.com Contents STGIPS20C60 Contents 1 Internal block diagram and pin configuration . . . . . . . . . . . . . . . . . . . . 3 2 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 2.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.1 Control part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.2 Waveforms definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 4 Smart shutdown function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5.1 6 7 2/20 Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6.1 SDIP-25L package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6.2 Packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 DocID024138 Rev 7 STGIPS20C60 1 Internal block diagram and pin configuration Internal block diagram and pin configuration Figure 1. Internal block diagram Pin 1 Pin 25 OUT U P VBOOT U LIN Vboot LIN-U SD/OD HVG HIN-U HIN VCC OUT U VCC DT LVG CP+ NU GND OUT V VBOOT V P LIN GND Vboot SD/OD HVG LIN-V HIN HIN-V VCC OUT V DT LVG CP+ NV GND OUT W VBOOT W P LIN Vboot LIN-W SD/OD HVG HIN-W HIN SD/OD VCC CIN OUT W DT LVG Pin 16 CP+ NW GND Pin 17 AM05002v1 DocID024138 Rev 7 3/20 20 Internal block diagram and pin configuration STGIPS20C60 Table 2. Pin description Pin n Symbol Description 1 OUTU High-side reference output for U phase 2 VbootU Bootstrap voltage for U phase 3 LINU Low-side logic input for U phase 4 HINU High-side logic input for U phase 5 VCC Low voltage power supply 6 OUTV High-side reference output for V phase 7 Vboot V Bootstrap voltage for V phase 8 GND Ground 9 LINV Low-side logic input for V phase 10 HINV High-side logic input for V phase 11 OUTW High-side reference output for W phase 12 Vboot W Bootstrap voltage for W phase 13 LINW Low-side logic input for W phase 14 HINW High-side logic input for W phase 15 SD / OD 16 CIN Comparator input 17 NW Negative DC input for W phase 18 W W phase output 19 P Positive DC input 20 NV 21 V V phase output 22 P Positive DC input 23 NU Negative DC input for U phase 24 U U phase output 25 P Positive DC input Shutdown logic input (active low) / open-drain (comparator output) Negative DC input for V phase Figure 2. Pin layout (bottom view) 0$5.,1*$5($ 4/20 DocID024138 Rev 7 STGIPS20C60 Electrical ratings 2 Electrical ratings 2.1 Absolute maximum ratings Table 3. Inverter part Symbol Parameter Value Unit VPN Supply voltage applied between P - NU, NV, NW 450 V VPN(surge) Supply voltage (surge) applied between P - NU, NV, NW 500 V VCES Each IGBT collector emitter voltage (VIN(1) = 0) 600 V Each IGBT continuous collector current at TC = 25C 20 A Each IGBT pulsed collector current 40 A Each IGBT total dissipation at TC = 25C 46 W Short circuit withstand time, VCE = 0.5 V(BR)CES TJ = 125 C, VCC = Vboot= 15 V, VIN (1)= 0 - 5 V 5 s Value Unit Vboot - 21 to Vboot + 0.3 V IC ICP (2) PTOT tscw 1. Applied between HINi, LINi and GND for i = U, V, W 2. Pulse width limited by max junction temperature Table 4. Control part Symbol Parameter VOUT Output voltage applied between OUTU, OUTV, OUTW - GND VCC Low voltage power supply - 0.3 to +21 V VCIN Comparator input voltage - 0.3 to VCC +0.3 V Vboot Bootstrap voltage applied between Vboot i - OUTi for i = U, V, W - 0.3 to 620 V Logic input voltage applied between HIN, LIN and GND - 0.3 to 15 V Open drain voltage - 0.3 to 15 V 50 V/ns Value Unit 2500 V VIN VSD/OD dVOUT/dt Allowed output slew rate Table 5. Total system Symbol VISO Parameter Isolation withstand voltage applied between each pin and heatsink plate (AC voltage, t = 60 sec.) Tj Power chips operating junction temperature - 40 to 150 C TC Module case operation temperature - 40 to 125 C DocID024138 Rev 7 5/20 20 Electrical ratings 2.2 STGIPS20C60 Thermal data Table 6. Thermal data Symbol RthJC Parameter Value Unit Thermal resistance junction-case single IGBT 2.7 C/W Thermal resistance junction-case single diode 5 C/W Figure 3. Maximum IC(RMS) current vs. switching frequency (1) AM17108v1 IC(RMS) (A) 28 3-phase sinusoidal PWM VPN = 300 V, Modulaon Index = 0.8, PF = 0.6, Tj = 150 C, fsine = 60 Hz 26 Figure 4. Maximum IC(RMS) current vs. fsine(1) IC(RMS) (A) AM17109v1 3-phase sinusoidal PWM VPN = 300 V, Modulation Index = 0.8, PF = 0.6, T j = 150 C, Tc = 100 C 17 16 Tc = 80 C fsw = 16 kHz fsw = 12 kHz 15 24 14 22 13 20 12 18 11 16 fsw = 20 kHz Tc = 100 C 10 14 9 12 8 4 8 12 16 f sw (kHz) 1 1. Simulated curves refer to typical IGBT parameters and maximum Rthj-c. 6/20 DocID024138 Rev 7 10 100 f sine (Hz) STGIPS20C60 3 Electrical characteristics Electrical characteristics TJ = 25 C unless otherwise specified. Table 7. Inverter part Value Symbol VCE(sat) ICES VF Parameter Test conditions Unit Min. Typ. Max. VCC = Vboot = 15 V, VIN(1)= 0 / 5 V, IC = 20 A - 1.6 2 VCC = Vboot = 15 V, VIN(1)= 0 / 5 V, IC = 20 A, TJ = 125 C - Collector-cut off current (VIN(1)= 0 "logic state") VCE = 550 V, VCC = VBoot = 15 V - 100 A Diode forward voltage VIN(1) = 0 "logic state", IC = 20 A - 2.2 V Collector-emitter saturation voltage V 1.7 Inductive load switching time and energy ton tc(on) toff tc(off) trr Turn-on time Crossover time (on) Turn-off time Crossover time (off) Reverse recovery time Eon Turn-on switching losses Eoff Turn-off switching losses VPN = 300 V, VCC = Vboot = 15 V, VIN(1) = 0 / 5 V, IC = 20 A (see Figure 5) - 390 - - 170 - - 970 - - 150 - - 284 - - 520 - - 460 - ns J 1. Applied between HINi, LINi and GND for i = U, V, W. (LIN inputs are active-low). Note: tON and tOFF include the propagation delay time of the internal drive. tC(ON) and tC(OFF) are the switching time of IGBT itself under the internally given gate driving condition. DocID024138 Rev 7 7/20 20 Electrical characteristics STGIPS20C60 Figure 5. Switching time test circuit INPUT VBOOT>VCC /SD HVG RSD L Hin VCC BUS BOOT /Lin +5V OUT Vcc IC DT LVG GND CP+ VCE 0 1 AM17099v1 Figure 6. Switching time definition 100% IC 100% IC t rr IC VCE VCE IC VIN VIN t ON t OFF t C(OFF) t C(ON) VIN(ON) 10% IC 90% IC 10% VCE (a) turn-on VIN(OFF) 10% VCE (b) turn-off 10% IC AM09223V1 Figure 4 "Switching time definition" refers to HIN inputs (active high). For LIN inputs (active low), VIN polarity must be inverted for turn-on and turn-off. 8/20 DocID024138 Rev 7 STGIPS20C60 3.1 Electrical characteristics Control part Table 8. Low voltage power supply (VCC = 15 V unless otherwise specified) Symbol Min. Typ. Max. Unit Vcc UV hysteresis 1.2 1.5 1.8 V Vcc_thON Vcc UV turn ON threshold 11.5 12 12.5 V Vcc_thOFF Vcc UV turn OFF threshold 10 10.5 11 V Vcc_hys Parameter Test conditions Iqccu Undervoltage quiescent supply current VCC = 10 V SD/OD = 5 V; LIN = 5 V; HIN = 0, CIN = 0 450 A Iqcc Quiescent current VCC = 15 V SD/OD= 5 V; LIN = 5 V HIN = 0, CIN = 0 3.5 mA Vref Internal comparator (CIN) reference voltage 0.58 V 0.5 0.54 Table 9. Bootstrapped voltage (VCC = 15 V unless otherwise specified) Symbol Min. Typ. Max. Unit VBS UV hysteresis 1.2 1.5 1.8 V VBS_thON VBS UV turn ON threshold 11.1 11.5 12.1 V VBS_thOFF VBS UV turn OFF threshold 9.8 10 10.6 V IQBSU Undervoltage VBS quiescent current VBS < 9 V SD/OD = 5 V; LIN and HIN = 5 V; CIN = 0 70 110 A IQBS VBS quiescent current VBS = 15 V SD/OD = 5 V; LIN and HIN = 5 V; CIN = 0 200 300 A Bootstrap driver on resistance LIN= 5 V; HIN= 0 V 120 VBS_hys RDS(on) Parameter Test conditions Table 10. Logic inputs (VCC = 15 V unless otherwise specified) Symbol Parameter Test conditions Min. Typ. Max. Unit Vil Low level logic threshold voltage 0.8 1.1 V Vih High level logic threshold voltage 1.9 2.25 V 260 A 1 A 20 A 1 A 300 A 3 A IHINh HIN logic "1" input bias current HIN = 15 V IHINl HIN logic "0" input bias current HIN = 0 V ILINl LIN logic "1" input bias current LIN = 0 V ILINh LIN logic "0" input bias current LIN = 15 V ISDh SD logic "0" input bias current SD = 15 V ISDl SD logic "1" input bias current SD = 0 V Dt Dead time see Figure 7 and Table 13 DocID024138 Rev 7 110 3 30 175 6 120 1.2 s 9/20 20 Electrical characteristics STGIPS20C60 Table 11. Sense comparator characteristics (VCC = 15 V unless otherwise specified) Symbol Parameter Test conditions Min. Typ. Max. Unit Iib Input bias current VCIN(i) = 1 V - 3 A Vol Open-drain low-level output voltage Iod = 3 mA - 0.5 V Comparator delay SD/OD pulled to 5 V through 100 k resistor - 90 130 ns SR Slew rate CL = 180 pF; Rpu = 5 k - 60 tsd Shut down to high / low side driver propagation delay VOUT = 0, Vboot = VCC, VIN = 0 to 3.3 V 50 125 tisd Comparator triggering to high / low side driver turn-off propagation delay Measured applying a voltage step from 0 V to 3.3 V to pin CIN td_comp V/sec 200 ns 50 200 250 Table 12. Truth table Logic input (VI) Output Condition SD/OD LIN HIN LVG HVG Shutdown enable half-bridge tri-state L X X L L Interlocking half-bridge tri-state H L H L L 0 `'logic state" half-bridge tri-state H H L L L 1 "logic state" low side direct driving H L L H L 1 "logic state" high side direct driving H H H L H Note: 10/20 X: don't care DocID024138 Rev 7 STGIPS20C60 Waveforms definition Figure 7. Dead time and interlocking waveforms definition HIN INTE RLO CK ING CONTROL SIGNAL EDGES OVERLAPPED: INTERLOCKING + DEAD TIME ING LIN INTE RLO CK 3.2 Electrical characteristics LVG DTHL DTLH HVG gate driver outputs OFF (HALF-BRIDGE TRI-STATE) gate driver outputs OFF (HALF-BRIDGE TRI-STATE) LIN CONTROL SIGNALS EDGES SYNCHRONOUS (*): DEAD TIME HIN LVG DTLH DTHL HVG gate driver outputs OFF (HALF-BRIDGE TRI-STATE) gate driver outputs OFF (HALF-BRIDGE TRI-STATE) LIN CONTROL SIGNALS EDGES NOT OVERLAPPED, BUT INSIDE THE DEAD TIME: DEAD TIME HIN LVG DTLH DTHL HVG gate driver outputs OFF (HALF-BRIDGE TRI-STATE) gate driver outputs OFF (HALF-BRIDGE TRI-STATE) LIN CONTROL SIGNALS EDGES NOT OVERLAPPED, OUTSIDE THE DEAD TIME: DIRECT DRIVING HIN LVG DTLH DTHL HVG gate driver outputs OFF (HALF-BRIDGE TRI-STATE) DocID024138 Rev 7 gate driver outputs OFF (HALF-BRIDGE TRI-STATE) 11/20 20 Smart shutdown function 4 STGIPS20C60 Smart shutdown function The STGIPS20C60 integrates a comparator for fault sensing purposes. The comparator has an internal voltage reference Vref connected to the inverting input, while the non-inverting input, available on pin (CIN), can be connected to an external shunt resistor in order to implement a simple over-current protection function. When the comparator triggers, the device is set in shutdown state and both its outputs are set to low-level leading the halfbridge in tri-state. In the common overcurrent protection architectures the comparator output is usually connected to the shutdown input through a RC network, in order to provide a mono-stable circuit, which implements a protection time that follows the fault condition. Our smart shutdown architecture allows to immediately turn-off the output gate driver in case of overcurrent, the fault signal has a preferential path which directly switches off the outputs. The time delay between the fault and the outputs turn-off is no more dependent on the RC values of the external network connected to the shutdown pin. At the same time the DMOS connected to the open-drain output (pin SD/OD) is turned on by the internal logic which holds it on until the shutdown voltage is lower than the logic input lower threshold (Vil). Finally the smart shutdown function provides the possibility to increase the real disable time without increasing the constant time of the external RC network. 12/20 DocID024138 Rev 7 STGIPS20C60 Smart shutdown function Figure 8. Smart shutdown timing waveforms comp Vref CP+ HIN/LIN PROTECTION HVG/LVG SD/OD open drain gate (internal) disable time Fast shut down: the driver outputs are set in SD state immediately after the comparator triggering even if the SD signal has not yet reach the lower input threshold An approximation of the disable time is given by: SHUT DOWN CIRCUIT VBIAS where: RSD SD/OD FROM/TO CONTROLLER CSD RON_OD SMART SD LOGIC RPD_SD AM12947v1 Please refer to Table 11 for internal propagation delay time details. DocID024138 Rev 7 13/20 20 14/20 3.3V/5V Line DocID024138 Rev 7 Csd Rsd Cbw Cbv CIN SD/OD HIN-W LIN-W VBOOT W OUT W HIN-V LIN-V GND VBOOT V OUT V VCC HIN-U LIN-U VBOOT U OUT U Rdt Cvcc Rdt Cvcc Rdt Cvcc Cdt Cdt Cdt OUT HIN OUT HIN OUT HIN GND DT CP+ LVG HVG VCC Vboot SD/OD CP+ LIN GND DT LVG HVG VCC Vboot SD/OD CP+ LIN GND DT LVG HVG SD/OD VCC Vboot LIN Rg Rg Rg Rg Rg Rg T6 T5 T4 T3 T2 T1 D6 D5 D4 D3 D2 D1 C R Nw W Nv V Nu U P Rshunt M + VDC 5 VCC Cbu Application information STGIPS20C60 Application information Figure 9. Typical application circuit CONTROLLER AM05001v2 STGIPS20C60 5.1 Application information Recommendations * Input signal HIN is active high logic. A 85 k (typ.) pull down resistor is built-in for each high side input. If an external RC filter is used, for noise immunity, pay attention to the variation of the input signal level. * Input signal LIN is active low logic. A 720 k (typ.) pull-up resistor, connected to an internal 5 V regulator through a diode, is built-in for each low side input. * To prevent the input signals oscillation, the wiring of each input should be as short as possible. * By integrating an application specific type HVIC inside the module, direct coupling to MCU terminals without any opto-coupler is possible. * Each capacitor should be located as nearby the pins of IPM as possible. * Low inductance shunt resistors should be used for phase leg current sensing. * Electrolytic bus capacitors should be mounted as close to the module bus terminals as possible. Additional high frequency ceramic capacitor mounted close to the module pins will further improve performance. * The SD/OD signal should be pulled up to 5 V / 3.3 V with an external resistor (see Section 4: Smart shutdown function for detailed info). Table 13. Recommended operating conditions Value Symbol Parameter Conditions Unit Min. VPN Note: Supply Voltage Applied between P-Nu,Nv,Nw VCC Control supply voltage Applied between VCC-GND VBS High side bias voltage tdead 13.5 Applied between VBOOTi-OUTi for i=U,V,W 13 Blanking time to prevent Arm-short For each input signal 1.5 fPWM PWM input signal -40C < Tc < 100C -40C < Tj < 125C TC Case operation temperature Typ. Max. 300 400 V 15 18 V 18 V s 20 kHz 100 C For further details, refer to AN3338. DocID024138 Rev 7 15/20 20 Package information 6 STGIPS20C60 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. Please refer to dedicated technical note TN0107 for mounting instructions. 6.1 SDIP-25L package information Figure 10. SDIP-25L package outline B 16/20 DocID024138 Rev 7 STGIPS20C60 Package information Table 14. SDIP-25L mechanical data mm Dim. Min. Typ. Max. A 43.90 44.40 44.90 A1 1.15 1.35 1.55 A2 1.40 1.60 1.80 A3 38.90 39.40 39.90 B 21.50 22.00 22.50 B1 11.25 11.85 12.45 B2 24.83 25.23 25.63 C 5.00 5.40 6.00 C1 6.50 7.00 7.50 C2 11.20 11.70 12.20 C3 2.90 3.00 3.10 e 2.15 2.35 2.55 e1 3.40 3.60 3.80 e2 4.50 4.70 4.90 e3 6.30 6.50 6.70 D 33.30 D1 5.55 E 11.20 E1 1.40 F 0.85 1.00 1.15 F1 0.35 0.50 0.65 R 1.55 1.75 1.95 T 0.45 0.55 0.65 V 0 6 DocID024138 Rev 7 17/20 20 Package information 6.2 STGIPS20C60 Packing information Base quantity: 11 pcs Bulk quantity: 132 pcs 8123127_E AM10488v1 Figure 11. SDIP-25L packing specification 18/20 DocID024138 Rev 7 STGIPS20C60 7 Revision history Revision history Table 15. Document revision history Date Revision 08-Mar-2013 1 Initial release 20-Mar-2013 2 Added Figure 3 and Figure 4 on page 6. 17-Jun-2013 3 Updated Dt value in Table 10: Logic inputs (VCC = 15 V unless otherwise specified), Figure 7: Dead time and interlocking waveforms definition and tdead in Table 13: Recommended operating conditions. 09-Jul-2013 4 Updated Dt value in Table 10: Logic inputs (VCC = 15 V unless otherwise specified). 16-Jul-2013 5 Updated Table 2: Pin description, Table 8: Low voltage power supply (VCC = 15 V unless otherwise specified) and Table 9: Bootstrapped voltage (VCC = 15 V unless otherwise specified) 14-May-2014 6 Updated Table 3: Inverter part, Table 6: Thermal data, Table 7: Inverter part and Section 7: Packaging mechanical data. Minor text changes. 7 Minor text and formating changes. Updated Figure 2 Section 6: Package information: - Renamed (was Package mechanical data) - Updated with revised package outline and mechanical data. - Added Section 6.2: Packing information (was Section 7: Packaging mechanical data) 20-Mar-2015 Changes DocID024138 Rev 7 19/20 20 STGIPS20C60 IMPORTANT NOTICE - PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST's terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers' products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. (c) 2015 STMicroelectronics - All rights reserved 20/20 DocID024138 Rev 7 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: STMicroelectronics: STGIPS20C60