Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, High Voltage, X7R Dielectric, 500 - 630 VDC (Automotive Grade) Overview KEMET Power Solutions (KPS) High Voltage stacked capacitors utilize a proprietary lead-frame technology to vertically stack one or two multilayer ceramic chip capacitors into a single compact surface mount package. The attached lead-frame mechanically isolates the capacitor(s) from the printed circuit board, thereby offering advanced mechanical and thermal stress performance. Isolation also addresses concerns for audible microphonic noise that may occur when a bias voltage is applied. A twochip stack offers up to double the capacitance in the same or smaller design footprint when compared to traditional surface mount MLCC devices. Providing up to 10 mm of board flex capability, KPS Series High Voltage capacitors are environmentally friendly and in compliance with RoHS legislation. KEMET's KPS Series devices in X7R dielectric exhibit a predictable change in capacitance with respect to time and voltage, and boast a minimal change in capacitance with reference to ambient temperature. Capacitance change is limited to 15% from -55C to +125C. These devices are capable of Pb-Free reflow profiles and provide lower ESR, ESL and higher ripple current capability when compared to other dielectric solutions. KPS Series Automotive Grade capacitors meet the demanding Automotive Electronics Council's AEC-Q200 qualification requirements. Benefits * * * * * * * * * * AEC Q200 automotive qualified -55C to +125C operating temperature range Reliable and robust termination system EIA 2220 case size DC voltage ratings of 500 V and 630 V Capacitance offerings ranging from 0.047 F up to 0.47 F Available capacitance tolerances of 10% and 20% Higher capacitance in the same footprint Potential board space savings Advanced protection against thermal and mechanical stress Click image above for interactive 3D content Open PDF in Adobe Reader for full functionality Ordering Information C Ceramic 2220 C Case Size Specification/ (L"x W") Series 2220 C = Standard 474 Capacitance Code (pF) Two significant digits and number of zeros. M C Rated Capacitance Voltage Tolerance1 (VDC) K = 10% M = 20% C = 500 B = 630 R 2 C AUTO Dielectric Failure Rate/ Design Leadframe Finish2 Packaging/Grade (C-Spec) R = X7R 1 = KPS Single Chip Stack 2 = KPS Double Chip Stack C = 100% Matte Sn See "Packaging C-Spec Ordering Options Table" Double chip stacks ("2" in the 13th character position of the ordering code) are only available in M (20%) capacitance tolerance. Single chip stacks ("1" in the 13th character position of the ordering code) are available in K (10%) or M (20%) tolerances. 2 Additional leadframe finish options may be available. Contact KEMET for details. 1 One world. One KEMET (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1037_X7R_KPS_HV_AUTO_SMD * 6/11/2018 1 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, High Voltage, X7R Dielectric, 500 VDC - 630 VDC (Automotive Grade) Packaging C-Spec Ordering Options Table Packaging Type1 Packaging/Grade Ordering Code (C-Spec)2 7" Reel (Embossed Plastic Tape)/Unmarked 13" Reel (Embossed Plastic Tape)/Unmarked AUTO AUTO 7289 The terms "Marked" and "Unmarked" pertain to laser marking option of capacitors. All packaging options labeled as "Unmarked" will contain capacitors that have not been laser marked. The option to laser mark is not available on these devices. For more information see "Capacitor Marking". 2 For additional information regarding "AUTO" C-Spec options, see "Automotive C-Spec Information". 1 Benefits cont'd * * * * Provides up to 10 mm of board flex capability Reduces audible microphonic noise Extremely low ESR and ESL Lead (Pb)-free, RoHS, and REACH compliant. * Capable of Pb-free reflow profiles * Non-polar device, minimizing installation concerns * Film alternative Applications Typical applications include switch mode power supplies (input filters, resonators, tank circuits, snubber circuits, output filters), high voltage coupling and DC blocking, lighting ballasts, voltage multiplier circuits, DC/DC converters and coupling capacitors in uk converters. Markets include power supply, LCD fluorescent backlight ballasts, HID lighting, telecom equipment, industrial and medical equipment/control, LAN/WAN interface, analog and digital modems, and automotive (electric and hybrid vehicles, charging stations and lighting applications). Application Note X7R dielectric is not recommended for AC line filtering or pulse applications. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1037_X7R_KPS_HV_AUTO_SMD * 6/11/2018 2 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, High Voltage, X7R Dielectric, 500 VDC - 630 VDC (Automotive Grade) Automotive C-Spec Information KEMET automotive grade products meet or exceed the requirements outlined by the Automotive Electronics Council. Details regarding test methods and conditions are referenced in document AEC-Q200, Stress Test Qualification for Passive Components. These products are supported by a Product Change Notification (PCN) and Production Part Approval Process warrant (PPAP). Automotive products offered through our distribution channel have been assigned an inclusive ordering code C-Spec, "AUTO." This C-Spec was developed in order to better serve small and medium-sized companies that prefer an automotive grade component without the requirement to submit a customer Source Controlled Drawing (SCD) or specification for review by a KEMET engineering specialist. This C-Spec is therefore not intended for use by KEMET OEM automotive customers and are not granted the same "privileges" as other automotive C-Specs. Customer PCN approval and PPAP request levels are limited (see details below.) Product Change Notification (PCN) The KEMET product change notification system is used to communicate primarily the following types of changes: * Product/process changes that affect product form, fit, function, and/or reliability * Changes in manufacturing site * Product obsolescence Process/Product change Obsolescence* Days Prior To Implementation KEMET assigned Yes (with approval and sign off) Yes 180 days minimum AUTO Yes (without approval) Yes 90 days minimum 1 1 Customer Notification Due To: KEMET Automotive C-Spec KEMET assigned C-Specs require the submittal of a customer SCD or customer specification for review. For additional information contact KEMET. Production Part Approval Process (PPAP) The purpose of the Production Part Approval Process is: * To ensure that supplier can meet the manufacturability and quality requirements for the purchased parts. * To provide the evidence that all customer engineering design records and specification requirements are properly understood and fulfilled by the manufacturing organization. * To demonstrate that the established manufacturing process has the potential to produce the part. 1 PPAP (Product Part Approval Process) Level KEMET Automotive C-Spec 1 2 3 4 5 KEMET assigned1 AUTO KEMET assigned C-Specs require the submittal of a customer SCD or customer specification for review. For additional information contact KEMET. Part number specific PPAP available Product family PPAP only (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1037_X7R_KPS_HV_AUTO_SMD * 6/11/2018 3 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, High Voltage, X7R Dielectric, 500 VDC - 630 VDC (Automotive Grade) Qualification/Certification Automotive Grade products meet or exceed the requirements outlined by the Automotive Electronics Council. Details regarding test methods and conditions are referenced in document AEC-Q200, Stress Test Qualification for Passive Components. For additional information regarding the Automotive Electronics Council and AEC-Q200, please visit their website at www.aecouncil.com. Environmental Compliance Lead (Pb)-free, RoHS, and REACH compliant without exemptions. Dimensions - Millimeters (Inches) TOP VIEW Single or Double Chip Stack PROFILE VIEW Double Chip Stack Single Chip Stack L L W H H LW LW Number of Chips EIA Size Code Metric Size Code L Length W Width H Height LW Lead Width Mounting Technique Single 2220 5650 Double 2220 5650 6.00 (0.236) 0.50 (0.020) 6.00 (0.236) 0.50 (0.020) 5.00 (0.197) 0.50 (0.020) 5.00 (0.197) 0.50 (0.020) 3.50 (0.138) 0.30 (0.012) 5.00 (0.197) 0.50 (0.020) 1.60 (0.063) 0.30 (0.012) 1.60 (0.063) 0.30 (0.012) Solder Reflow Only (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1037_X7R_KPS_HV_AUTO_SMD * 6/11/2018 4 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, High Voltage, X7R Dielectric, 500 VDC - 630 VDC (Automotive Grade) Electrical Parameters/Characteristics Item Parameters/Characteristics Operating Temperature Range -55C to +125C Capacitance Change with Reference to +25C and 0 Vdc Applied (TCC) 15% Aging Rate (Maximum % Capacitance Loss/Decade Hour) 3.0% 1 2 3 4 Dielectric Withstanding Voltage (DWV) Dissipation Factor (DF) Maximum Limit at 25C Insulation Resistance (IR) Minimum Limit at 25C 150% of rated voltage for voltage rating of < 1000V 120% of rated voltage for voltage rating of 1000V (51 seconds and charge/discharge not exceeding 50mA) 2.5% 1,000 megohm microfarads or 100G (500 VDC applied for 1205 seconds at 25C) Regarding Aging Rate: Capacitance measurements (including tolerance) are indexed to a referee time of 1,000 hours. DWV is the voltage a capacitor can withstand (survive) for a short period of time. It exceeds the nominal and continuous working voltage of the capacitor. 3 Capacitance and dissipation factor (DF) measured under the following conditions: 1kHz 50Hz and 1.0 0.2 Vrms if capacitance 10F 120Hz 10Hz and 0.5 0.1 Vrms if capacitance > 10F 4 To obtain IR limit, divide M-F value by the capacitance and compare to G limit. Select the lower of the two limits. Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known as Automatic Level Control (ALC). The ALC feature should be switched to "ON". 1 2 Post Environmental Limits High Temperature Life, Biased Humidity, Moisture Resistance Dielectric X7R Rated DC Voltage > 25 16/25 < 16 Capacitance Value All Dissipation Factor (Maximum %) 3.0 5.0 7.5 Capacitance Shift Insulation Resistance 20% 10% of Initial Limit (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1037_X7R_KPS_HV_AUTO_SMD * 6/11/2018 5 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, High Voltage, X7R Dielectric, 500 VDC - 630 VDC (Automotive Grade) Table 1 - Capacitance Range/Selection Waterfall (2220 Case Sizes) Case Size/Series Capacitance Capacitance Code 0.047 F 0.10 F 0.15 F 0.22 F 473 104 154 224 0.10 F 0.22 F 0.33 F 0.47 F 104 224 334 474 Capacitance Capacitance Code C2220C Voltage Code C B D Rated Voltage (VDC) 500 630 1000 Capacitance Tolerance Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions Single Chip Stack K K K K M M M M JP JP JP JP JP JP JP JP M M M M JR JR JR JR JR JR JR JR 500 C 630 B Double Chip Stack Rated Voltage (VDC) Voltage Code Case Size/Series 1000 D C2220C These products are protected under US Patent 8,331,078 other patents pending, and any foreign counterparts. Table 2 - Chip Thickness/Tape & Reel Packaging Quantities Paper Quantity Plastic Quantity Thickness Code Case Size Thickness Range (mm) 7" Reel 13" Reel 7" Reel 13" Reel JP 2220 3.50 0.30 0 0 300 1,300 JR 2220 5.00 0.50 0 0 200 800 Package quantity based on finished chip thickness specifications. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1037_X7R_KPS_HV_AUTO_SMD * 6/11/2018 6 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, High Voltage, X7R Dielectric, 500 VDC - 630 VDC (Automotive Grade) Table 3 - KPS Land Pattern Design Recommendations (mm) V1 Median (Nominal) Land Protrusion EIA SIZE CODE METRIC SIZE CODE C Y X V1 V2 2220 5650 2.69 2.08 4.78 7.70 6.00 Y Y X X C C V2 Grid Placement Courtyard Soldering Process To prevent degradation of temperature cycling capability, care must be taken to prevent solder from flowing into the inner side of the lead frames (inner side of "J" lead in contact with the circuit board). After soldering, the capacitors should be air cooled to room temperature before further processing. Forced air cooling is not recommended. Hand soldering should be performed with care due to the difficulty in process control. If performed, care should be taken to avoid contact of the soldering iron to the capacitor body. The iron should be used to heat the solder pad, applying solder between the pad and the lead, until reflow occurs. Once reflow occurs, the iron should be removed immediately. (Preheating is required when hand soldering to avoid thermal shock.) Profile Feature SnPb Assembly Pb-Free Assembly Preheat/Soak Temperature Minimum (TSmin) 100C 150C Temperature Maximum (TSmax) 150C 200C Time (ts) from Tsmin to Tsmax) 60 - 120 seconds 60 - 120 seconds Ramp-up Rate (TL to TP) 3C/seconds maximum 3C/seconds maximum Liquidous Temperature (TL) 183C 217C Time Above Liquidous (tL) 60 - 150 seconds 60 - 150 seconds Peak Temperature (TP) 235C 250C Time within 5C of Maximum Peak Temperature (tP) 20 seconds maximum 10 seconds maximum Ramp-down Rate (TP to TL) Time 25C to Peak Temperature 6C/seconds maximum 6C/seconds maximum 6 minutes maximum 8 minutes maximum Note: All temperatures refer to the center of the package, measured on the package body surface that is facing up during assembly reflow. TP TL Temperature KEMET's KPS Series devices are compatible with IR reflow techniques. Preheating of these components is recommended to avoid extreme thermal stress. KEMET's recommended profile conditions for IR reflow reflect the profile conditions of the IPC/J-STD-020D standard for moisture sensitivity testing. tP Maximum Ramp Up Rate = 3C/second Maximum Ramp Down Rate = 6C/second tL Tsmax Tsmin 25 ts 25C to Peak Time (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1037_X7R_KPS_HV_AUTO_SMD * 6/11/2018 7 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, High Voltage, X7R Dielectric, 500 VDC - 630 VDC (Automotive Grade) Construction Detailed Cross Section Dielectric Material (BaTiO3) Leadframe (Phosphor Bronze - Alloy 510) Leadframe Attach (High Melting Point Solder) Inner Electrodes (Ni) End Termination/ External Electrode (Cu) Barrier Layer (Ni) Dielectric Material (BaTiO3) Termination Finish (Sn) Termination Finish (Sn) Inner Electrodes Barrier Layer (Ni) (Ni) End Termination/ External Electrode (Cu) Product Marking Laser marking option is not available on: * * * * C0G, Ultra Stable X8R and Y5V dielectric devices EIA 0402 case size devices EIA 0603 case size devices with Flexible Termination option. KPS Commercial and Automotive grade stacked devices. These capacitors are supplied unmarked only. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1037_X7R_KPS_HV_AUTO_SMD * 6/11/2018 8 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, High Voltage, X7R Dielectric, 500 VDC - 630 VDC (Automotive Grade) Tape & Reel Packaging Information KEMET offers multilayer ceramic chip capacitors packaged in 8, 12 and 16 mm tape on 7" and 13" reels in accordance with EIA Standard 481. This packaging system is compatible with all tape-fed automatic pick and place systems. See Table 2 for details on reeling quantities for commercial chips. Embossed Carrier Embossment 12 mm (0.472") or 16 mm (0.629") Top Tape Thickness 0.10 mm (0.004") Maximum Thickness 180 mm (7.0") or 330 mm (13.0") Table 4 - Carrier Tape Configuration - Embossed Plastic (mm) EIA Case Size Tape Size (W)* Pitch (P1)* 01005 - 0402 8 2 0603 - 1210 8 4 1805 - 1808 12 4 1812 12 8 KPS 1210 12 8 KPS 1812 & 2220 16 12 Array 0508 & 0612 8 4 *Refer to Figure 1 for W and P1 carrier tape reference locations. *Refer to Table 5 for tolerance specifications. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1037_X7R_KPS_HV_AUTO_SMD * 6/11/2018 9 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, High Voltage, X7R Dielectric, 500 VDC - 630 VDC (Automotive Grade) Figure 1 - Embossed (Plastic) Carrier Tape Dimensions P2 T T2 OD0 P0 (10 pitches cumulative tolerance on tape 0.2 mm) A0 E1 F K0 B1 B0 S1 W E2 P1 T1 Center Lines of Cavity B1 is for tape feeder reference only, including draft concentric about B0. Embossment For cavity size, see Note 1 Table 4 OD1 Cover Tape User Direction of Unreeling Table 5 - Embossed (Plastic) Carrier Tape Dimensions Metric will govern Constant Dimensions -- Millimeters (Inches) Tape Size D0 8 mm 12 mm 1.5+0.10/0.0-0.0 (0.059+0.004/-0.0) 16 mm D1 Minimum Note 1 1.0 (0.039) 1.5 (0.059) E1 P0 P2 1.750.10 4.00.10 2.00.05 (0.0690.004) (0.1570.004) (0.0790.002) R Reference Note 2 25.0 (0.984) 30 (1.181) S1 Minimum Note 3 T Maximum T1 Maximim 0.600 (0.024) 0.600 (0.024) 0.100 (0.004) Variable Dimensions -- Millimeters (Inches) Tape Size Pitch 8 mm Single (4 mm) 12 mm Single (4 mm) & Double (8 mm) 16 mm Triple (12 mm) B1 Maximum E2 Minimum Note 4 4.35 6.25 (0.171) (0.246) 8.2 10.25 (0.323) (0.404) 12.1 14.25 (0.476) (0.561) F P1 3.50.05 4.00.10 (0.1380.002) (0.1570.004) 5.50.05 8.00.10 (0.2170.002) (0.3150.004) 7.50.05 12.00.10 (0.1380.002) (0.1570.004) T2 Maximum 2.5 (0.098) 4.6 (0.181) 4.6 (0.181) W Maximum 8.3 (0.327) 12.3 (0.484) 16.3 (0.642) A0 , B 0 & K0 Note 5 1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 2. The tape with or without components shall pass around R without damage (see Figure 5). 3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481 paragraph 4.3 section b). 4. B1 dimension is a reference dimension for tape feeder clearance only. 5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that: (a) the component does not protrude above the top surface of the carrier tape. (b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. (c) rotation of the component is limited to 20 maximum for 8 and 12 mm tapes and 10 maximum for 16 mm tapes (see Figure 2). (d) lateral movement of the component is restricted to 0.5 mm maximum for 8 and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 3). (e) for KPS Series product, A0 and B0 are measured on a plane 0.3 mm above the bottom of the pocket. (f) see Addendum in EIA Standard 481 for standards relating to more precise taping requirements. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1037_X7R_KPS_HV_AUTO_SMD * 6/11/2018 10 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, High Voltage, X7R Dielectric, 500 VDC - 630 VDC (Automotive Grade) Packaging Information Performance Notes 1. Cover Tape Break Force: 1.0 Kg minimum. 2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be: Tape Width Peel Strength 8 mm 0.1 to 1.0 newton (10 to 100 gf) 12 and 16 mm 0.1 to 1.3 newton (10 to 130 gf) The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165 to 180 from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 10 mm/minute. 3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA Standards 556 and 624. Figure 2 - Maximum Component Rotation T Maximum Component Rotation Top View Maximum Component Rotation Side View Typical Pocket Centerline Tape Maximum Width (mm) Rotation ( 8,12 20 16 - 200 10 Bo T) Typical Component Centerline Ao Figure 3 - Maximum Lateral Movement 8 mm & 12 mm Tape 0.5 mm maximum 0.5 mm maximum s Tape Width (mm) 8,12 16 - 56 72 - 200 Maximum Rotation ( 20 10 5 Figure 4 - Bending Radius Embossed Carrier 16 mm Tape S) Punched Carrier 1.0 mm maximum 1.0 mm maximum R (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com Bending Radius R C1037_X7R_KPS_HV_AUTO_SMD * 6/11/2018 11 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, High Voltage, X7R Dielectric, 500 VDC - 630 VDC (Automotive Grade) Figure 5 - Reel Dimensions Full Radius, See Note W3 (Includes flange distortion at outer edge) Access Hole at Slot Location (O 40 mm minimum) W2 D A (See Note) N C (Arbor hole diameter) B (see Note) (Measured at hub) W1 (Measured at hub) If present, tape slot in core for tape start: 2.5 mm minimum width x 10.0 mm minimum depth Note: Drive spokes optional; if used, dimensions B and D shall apply. Table 6 - Reel Dimensions Metric will govern Constant Dimensions -- Millimeters (Inches) Tape Size A B Minimum C D Minimum 8 mm 1780.20 (7.0080.008) or 3300.20 (13.0000.008) 1.5 (0.059) 13.0+0.5/-0.2 (0.521+0.02/-0.008) 20.2 (0.795) 12 mm 16 mm Variable Dimensions -- Millimeters (Inches) Tape Size N Minimum W1 W2 Maximum W3 50 (1.969) 8.4+1.5/-0.0 (0.331+0.059/-0.0) 12.4+2.0/-0.0 (0.488+0.078/-0.0) 16.4+2.0/-0.0 (0.646+0.078/-0.0) 14.4 (0.567) 18.4 (0.724) 22.4 (0.882) Shall accommodate tape width without interference 8 mm 12 mm 16 mm (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1037_X7R_KPS_HV_AUTO_SMD * 6/11/2018 12 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, High Voltage, X7R Dielectric, 500 VDC - 630 VDC (Automotive Grade) Figure 6 - Tape Leader & Trailer Dimensions Embossed Carrier Punched Carrier 8 mm & 12 mm only END Carrier Tape Round Sprocket Holes START Top Cover Tape Elongated Sprocket Holes (32 mm tape and wider) Trailer 160 mm minimum Components 100 mm minimum leader 400 mm minimum Top Cover Tape Figure 7 - Maximum Camber Elongated Sprocket Holes (32 mm & wider tapes) Carrier Tape Round Sprocket Holes 1 mm maximum, either direction Straight Edge 250 mm (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1037_X7R_KPS_HV_AUTO_SMD * 6/11/2018 13 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, High Voltage, X7R Dielectric, 500 VDC - 630 VDC (Automotive Grade) KEMET Electronics Corporation Sales Offices For a complete list of our global sales offices, please visit www.kemet.com/sales. Disclaimer All product specifications, statements, information and data (collectively, the "Information") in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation's ("KEMET") knowledge of typical operating conditions for such applications, but are not intended to constitute - and KEMET specifically disclaims - any warranty concerning suitability for a specific customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET's products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. KEMET is a registered trademark of KEMET Electronics Corporation. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1037_X7R_KPS_HV_AUTO_SMD * 6/11/2018 14