DG428/429 Single 8-Ch/Differential 4-Ch Latchable Analog Multiplexers Features Benefits Applications Low rDS(on): 55 Low Charge Injection: 1 pC On-Board TTL Compatible Address Latches High Speed--tTRANS: 160 ns Break-Before-Make Low Power Consumption: 0.3 mW Improved System Accuracy Microprocessor Bus Compatible Easily Interfaced Reduced Crosstalk High Throughput Improved Reliability rs Data Acquisition Systems Automatic Test Equipment Avionics and Military Systems Communication Systems Microprocessor-Controlled Analog Systems Medical Instrumentation Description The DG428/DG429 analog multiplexers have on-chip address and control latches to simplify design in microprocessor based applications. Break-before-make switching action protects against momentary crosstalk of adjacent input signals. all switches off for stacking several devices. All control inputs, address (Ax) and enable (EN) are TTL compatible over the full specified operating temperature range. The DG428 selects one of eight single-ended inputs to a common output, while the DG429 selects one of four differential inputs to a common differential output. The silicon-gate CMOS process enables operation over a wide range of supply voltages. The absolute maximum voltage rating is extended to 44 V. Additionally, single supply operation is also allowed and an epitaxial layer prevents latchup. An on channel conducts current equally well in both directions. In the off state each channel blocks voltages up to the power supply rails. An enable (EN) function allows the user to reset the multiplexer/demultiplexer to On-board TTL-compatible address latches simplify the digital interface design and reduce board space in bus-controlled systems such as data acquisition systems, process controls, avionics, and ATE. Functional Block Diagrams and Pin Configurations RS 3 2 1 20 19 A1 NC PLCC WR DG428 A0 DG428 Dual-In-Line WR 1 18 RS A0 2 17 A1 EN 3 Latches 16 A2 EN 4 Latches 18 A2 V- 4 Decoders/Drivers 15 GND V- 5 Decoders/Drivers 17 GND 16 V+ 5 14 V+ S1 6 S1 S2 7 15 S5 S2 6 13 S5 S3 8 14 S6 S3 7 12 S6 S4 8 11 S7 D 9 10 S8 S7 S8 NC D S4 9 10 11 12 13 Top View Top View Updates to this data sheet may be obtained via facsimile by calling Siliconix FaxBack, 1-408-970-5600. Please request FaxBack document #70063. Siliconix S-56532--Rev. H, 19-Jan-98 1 DG428/429 Functional Block Diagrams and Pin Configurations (Cont'd) RS 3 2 1 20 19 A1 NC PLCC WR DG429 A0 DG429 Dual-In-Line and SOIC WR 1 18 RS A0 2 17 A1 EN 3 Latches 16 GND EN 4 Latches 18 GND 4 Decoders/Drivers V+ V- 5 Decoders/Drivers 17 VDD S1a 6 16 S1b S2a 7 15 S2b S3a 8 14 S3b S1b S2a 6 13 S2b S3a 7 12 S3b S4a 8 11 S4b Da 9 10 Db 9 10 11 12 13 S 4b 14 Db 5 NC S1a Da 15 S 4a V- Top View Top View Truth Table -- DG428 8-Channel Single-Ended Multiplexer A2 A1 A0 EN WR RS On Switch X X X X 1 Maintains previous switch condition A0 EN WR RS On Switch X X X 1 Maintains previous switch condition X X 0 None (latches cleared) X X X X 0 None (latches cleared) X X X X X 0 0 1 None X X 0 0 1 None 0 0 0 1 0 1 1 0 0 1 0 1 1 0 0 1 1 0 1 2 0 1 1 0 1 2 0 1 0 1 0 1 3 1 0 1 0 1 3 0 1 1 1 0 1 4 1 1 1 0 1 4 1 0 0 1 0 1 5 1 0 1 1 0 1 6 1 1 0 1 0 1 7 1 1 1 1 0 1 8 Ordering Information -- DG428 Temp Range -40 to 85_C -55 to 125_C 2 A1 X Truth Table -- DG429 Differential 4-Channel Multiplexer Package Part Number 18-Pin Plastic DIP DG428DJ 20-Pin PLCC 18-Pin CerDIP DG428DN DG428AK DG428AK/883 Logic L i "0" = VAL 00.88 V Logic "1" = VAH 2.4 24V X = Don't Don t Care Ordering Information -- DG429 Temp Range -40 to 85_C -55 to 125_C Package Part Number 18-Pin Plastic DIP DG429DJ 20-Pin PLCC DG429DN 18-Pin Widebody SOIC DG429DW 18-Pin CerDIP DG429AK DG429AK/883 Siliconix S-56532--Rev. H, 19-Jan-98 DG428/429 Absolute Maximum Ratings Power Dissipation (Package)b 18-Pin Plastic DIPc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470 mW 18-Pin CerDIPd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 900 mW 20-Pin PLCCe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800 mW Voltage Referenced to V- V+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 V GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 V Digital Inputsa, VS, VD . . . . . . . . . . . . . . . (V-) -2 V to (V+) +2 V or 30 mA, whichever occurs first 28-Pin Widebody SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450 mW Notes: a. Signals on SX, DX or INX exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings. b. All leads soldered or welded to PC board. c. Derate 6.3 mW/_C above 75_C. d. Derate 12 mW/_C above 75_C. e. Derate 10 mW/_C above 75_C. Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 mA Peak Current, S or D (Pulsed at 1 ms, 10% Duty Cycle Max) . . . . . . . . . . . . . . . . . . 100 mA Storage Temperature (AK Suffix) . . . . . . . . . . . . -65 to 150_C (DJ, DN Suffix) . . . . . . . . . -65 to 125_C Specificationsa Test Conditions Unless Otherwise Specified A Suffix D Suffix -55 to 125_C -40 to 85_C V+ = 15 V, V- = -15 V, WR = 0, RS = 2.4 V, VIN = 2.4 V, 0.8 Vf Tempb rDS(on) VD = "10 V, VAL = 0.8 V IS = -1 mA, VAH = 2.4 V Room Full 55 DrDS(on) -10 V < VS < 10 V IS = -1 mA Room 5 Source Off Leakage Current IS(off) VS = "10 V, VD = #10 V VEN = 0 V Room Full "0.03 -0.5 -50 0.5 50 -0.5 -50 0.5 50 DG428 ID(off) Room Full "0.07 Drain Off L k Leakage C Current -1 -100 1 100 -1 -100 1 100 DG429 Room Full "0.05 -1 -50 1 50 -1 -50 1 50 DG428 Room Full "0.07 -1 -100 1 100 -1 -100 1 100 DG429 Room Full "0.05 -1 -50 1 50 -1 -50 1 50 VA = 2.4 V Full 0.01 1 1 VA = 15 V Full 0.01 1 1 Full -0.01 Parameter Symbol Typc Mind Maxd Mind Maxd Unit Analog Switch Analog Signal Rangee VANALOG Drain-Source On-Resistance Greatest Change in rDS(on) Between Channelsg Drain On Leakage Current L k C ID(on) Full VD = "10 V VS = #10 V VEN = 0 V VS = VD = "10 V VEN = 2.4 V VAL = 0.8 V VAH = 2.4 V -15 15 -15 100 125 15 V 100 125 W % nA Digital Control Logic g Input p Current I Input tV Voltage lt Hi High h IAH Logic Input Current Input Voltage Low IAL VEN = 0 V, 2.4 V, VA = 0 V RS = 0 V, WR = 0 V Logic Input Capacitance Cin f = 1 MHz Room 8 Transition Time tTRANS See Figure 5 Room Full 150 Break-Before-Make Interval tOPEN See Figure 4 Full 30 Enable and Write Turn-On Time tON(EN,WR) See Figures 6 and 7 Room Full 90 150 225 150 225 Enable and Reset Turn-Off Time tOFF(EN,RS) See Figures 6 and 8 Room Full 55 150 300 150 300 Charge Injection Q VGEN = 0 V, RGEN = 0 W CL = 1 nF, See Figure 9 Room 1 -1 mA -1 pF Dynamic Characteristics 250 300 10 250 300 10 ns Siliconix S-56532--Rev. H, 19-Jan-98 pC 3 DG428/429 Specificationsa (Cont'd) Test Conditions Unless Otherwise Specified Parameter Symbol V+ = 15 V, V- = -15 V, WR = 0, RS = 2.4 V, VIN = 2.4 V, 0.8 Vf Tempb Typc -75 A Suffix D Suffix -55 to 125_C -40 to 85_C Mind Maxd Mind Maxd Unit Dynamic Characteristics (Cont'd) Off Isolation OIRR VEN = 0 V, RL = 300 W, CL = 15 pF VS = 7 VRMS, f = 100 kHz Room Source Off Capacitance CS(off) VS = 0 V, VEN = 0 V, f = 1 MHz Drain Off Capacitance Drain On Capacitance CD(off) VD = 0 V,, VEN = 0 V f = 1 MHz MH CD(on) Room 11 DG428 Room 40 DG429 Room 20 DG428 Room 54 DG429 Room 34 dB ppF Minimum Input Timing Requirements Write Pulse Width tW AX, EN Data Set Up time tS AX, EN Data Hold Time tH Reset Pulse Width tRS See Figure 2 VS = 5 V, See Figure 3 Full 100 100 Full 100 100 Full 10 10 Full 100 100 ns Power Supplies Positive Supply Current Negative Supply Current I+ I- VEN = 0 V, VA = 0, RS = 5 V Room 20 100 Room -0.001 -5 100 mA A -5 Specificationsa for Single Supply Test Conditions Unless Otherwise Specified Parameter Symbol V+ = 12 V, V- = 0 V, WR = 0 RS = 2.4 V, VIN = 2.4 V, 0.8 Vf Tempb Typc A Suffix D Suffix -55 to 125_C -40 to 85_C Mind Maxd Mind Maxd Unit 0 12 0 12 V 150 W Analog Switch Analog Signal Rangee Drain-Source On-Resistance rDS(on) Matchg Source Off Leakage Current Drain Off L k Leakage C Current Drain On L k Leakage C Current VANALOG Full rDS(on) VD = +10 V, VAL = 0.8 V IS = -500 mA, VAH = 2.4 V Room 80 DrDS(on) 0 V < VS < 10 V IS = -1 mA Room 5 IS(off) VS = 0 V, 10 V, VD = 10 V, 0 V VEN = 0 V Room Full 0.03 -0.5 -50 0.5 50 -0.5 -50 0.5 50 ID(off) ID(on) 150 % VD = 0 V, 10 V VS = 10 V V, 0 V VEN = 0 V DG428 Room Full 0.07 -1 -100 1 100 -1 -100 1 100 DG429 Room Full 0.05 -1 -50 1 50 -1 -50 1 50 VS = VD = 0 V, 10 V VEN = 2.4 V VAL = 0.8 V VAH = 2.4 V DG428 Room Full 0.07 -1 -100 1 100 -1 -100 1 100 DG429 Room Full 0.05 -1 -50 1 50 -1 -50 1 50 nA Digital Control Logic g Input p Current I tV Input Voltage lt Hi High h Logic Input Current Input Voltage Low 4 IAH IAL VA = 2.4 V Full 1 1 VA = 12 V Full 1 1 VEN = 0 V, 2.4 V, VA = 0 V RS = 0 V, WR = 0 V Full -1 mA -1 Siliconix S-56532--Rev. H, 19-Jan-98 DG428/429 Specificationsa for Single Supply (Cont'd) Test Conditions Unless Otherwise Specified Parameter Symbol V+ = 12 V, V- = 0 V, WR = 0 RS = 2.4 V, VIN = 2.4 V, 0.8 Vf Tempb Typc A Suffix D Suffix -55 to 125_C -40 to 85_C Mind Maxd Mind Maxd Unit Dynamic Characteristics Transition Time tTRANS S1 = 10 V/2 V, S8 = 2 V/ 10 V See Figure 5 Room Full 160 Break-Before-Make Interval tOPEN See Figure 4 Room Full 40 Enable and Write Turn-On Time tON(EN, S1 =5 V See Figures 6 and 7 Room Full 110 300 400 300 400 Enable and Reset Turn-Off Time tOFF(EN, S1 =5 V See Figures 6 and 8 Room Full 70 300 400 300 400 Charge Injection Q VGEN = 6 V, RGEN = 0 W CL = 1 nF, See Figure 9 Room 4 pC OIRR VEN = 0 V, RL = 300 W, CL = 15 pF VS = 7 VRMS, f = 100 kHz Room -75 dB WR) RS) Off Isolation 280 350 25 10 280 350 25 10 ns Minimum Input Timing Requirements Write Pulse Width tW AX, EN Data Set Up Time tS AX, EN Data Hold Time tH Reset Pulse Width tRS I+ Full 100 100 Full 100 100 Full 10 10 VS = 5 V, See Figure 3 Full 100 100 VEN = 0 V, VA = 0, RS = 5 V Room See Figure 2 ns Power Supplies Positive Supply Current 20 100 100 mA Notes: a. b. c. d. e. f. g. Refer to PROCESS OPTION FLOWCHART. Room = 25_C, Full = as determined by the operating temperature suffix. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. Guaranteed by design, not subject to production test. VIN = input voltage to perform proper function. * D + Siliconix S-56532--Rev. H, 19-Jan-98 5 DG428/429 Typical Characteristics rDS(on) vs. VD and Supply Voltage 120 5 V 100 10 V 80 12 V 8 V 15 V 60 40 20 V 20 0 -20 -16 -12 -8 -4 0 4 8 12 16 rDS vs. VD and Temperature 100 rDS(on) - Drain-Source On-Resistance ( rDS(on) - Drain-Source On-Resistance ( 140 90 80 70 125_C 60 85_C 50 25_C 40 30 -55_C 20 -40_C V+ = 15 V V- = -15 V 10 0 20 -15 -10 VD - Drain Voltage (V) Single Supply rDS(on) vs. VD and Supply 40 V+ = 7.5 V 120 10 V 12 V 80 15 V 20 V 20 10 IS(off) 0 ID(on), ID(off) -10 40 -20 0 -30 0 4 8 12 16 20 -15 VD - Drain Voltage (V) 0 5 10 15 Switching Times vs. Power Supply Voltage 200 1 nA IS (off) Time (ns) I S , I D - Leakage Current -5 250 V+ = 15 V V- = -15 V VS, VD = 14 V 100 pA -10 VS,VD - Source, Drain Voltage (V) ID, IS Leakages vs. Temperature 10 nA ID(on), ID(off) tTRANS 150 tON(EN) 100 10 pA tOFF(EN) 50 1 pA 0 -55 -35 -15 5 25 45 65 Temperature (C_) 6 15 V+ = 15 V V- = -15 V VS = -VD for ID(off) VD = VS for ID(on) 30 160 10 ID, IS Leakage Currents vs. Analog Voltage V- = 0 V I S , I D - Current (pA) rDS(on) - Drain-Source On-Resistance ( 200 -5 0 5 VD - Drain Voltage (V) 85 105 125 5 10 15 20 Supply Voltage (V) Siliconix S-56532--Rev. H, 19-Jan-98 DG428/429 Typical Characteristics (Cont'd) Charge Injection vs. Analog Voltage Switching Times vs. Single Supply 350 V- = 0 V 60 300 40 Q - Charge (pC) Time (ms) 250 200 tTRANS 150 tON V+ = 12 V V- = 0 V 20 0 -20 100 -40 tOFF 50 V+ = 15 V V- = -15 V -60 0 5 10 15 -15 20 -10 -5 V+ - Positive Supply (V) 0 5 10 15 VS - Source Voltage (V) Off-Isolation vs. Frequency Supply Current vs. Switching Frequency 8 -140 I+ EN = 5 V AX = 0 or 5 V 6 -120 Supply Current (ma) 4 OIRR (dB) -100 -80 -60 -40 2 IGND 0 -2 -4 -6 I- -20 -8 1k 10 k 100 k 1M 10 M 1k 10 k f - Frequency (Hz) 100 k 1M 10 M f - Frequency (Hz) Switching Times vs. Temperature Input Switching Threshold vs. Supply Voltage 200 3 V+ = 15 V V- = -15 V tTRANS 2.5 150 V in (V) Time (nS) 2 tON 100 tOFF 1.5 1 50 0.5 0 -55 -35 0 -15 5 25 45 65 Temperature (C_) Siliconix S-56532--Rev. H, 19-Jan-98 85 105 125 0 "5 "10 "15 "20 VSUPPLY - Supply Voltage (V) 7 DG428/429 Schematic Diagram (Typical Channel) V+ GND VREF D EN DO QO V+ V- AX Dn Level Shift Qn Decode/ Drive S1 Latches WR CLK RESET V+ Sn RS V- V- Figure 1. Timing Diagrams 3V 3V 50% WR 50% RS 0V tRS 0V tW tS 3V A0, A1, (A2) EN 0V tOFF(RS) tH VO Switch Output 20% 80% 80% 0V Figure 2. Figure 3. Test Circuits +15 V +2.4 V RS EN V+ Logic Input +5 V All S and Da tr <20 ns tf <20 ns 3V 50% 0V DG428 DG429 A0, A1, (A2) GND WR 50 Db , D V- -15 V VO 300 35 pF VS Switch Output VO 0V 80% tOPEN Figure 4. Break-Before-Make 8 Siliconix S-56532--Rev. H, 19-Jan-98 DG428/429 Test Circuits (Cont'd) +15 V V+ RS EN +2.4 V S1 "10 V S2 - S7 A0 DG428 A1 S8 A2 D GND WR V- #10 V 50 Logic Input VO 300 -15 V Switch Output VO V+ RS EN 50% 0V 35 pF +15 V +2.4 V #10 V S1b VS1 A1 GND WR 50 V- Db 10% VS8 tTRANS S1 ON #10 V S4b DG429 90% 0V S1a - S4a, Da S2b and S3b A0 tr <20 ns tf <20 ns 3V tTRANS S8 ON VO 300 -15 V 35 pF Figure 5. Transition Time +15 V +2.4 V V+ RS EN A0 A1 A2 GND -5V S1 DG428 S2 - S8 V- WR 50 VO D 300 -15 V 35 pF Logic Input tr <20 ns tf <20 ns 3V 50% 0V tON(EN) tOFF(EN) 0V +15 V +2.4 V Switch Output VO V+ RS EN A0 A1 GND 50 -5V S1b DG429 VO S1a - S4a, Da S2b - S4b WR Db V- 90% VO 300 -15 V 35 pF Figure 6. Enable tON/tOFF Time Siliconix S-56532--Rev. H, 19-Jan-98 9 DG428/429 Test Circuits (Cont'd) +15 V V+ EN S1 or S1b A0, A1, (A2) Remaining Switches RS +2.4 V +5 V 3 V WR 50% 0 V VO DG428 DG429 Db, D WR GND V- VO 20% 35 pF 300 W tON(WR) Switch Output 0V -15 V Figure 7. Write Turn-On Time tON(WR) +15 V +2.4 V V+ EN S1 or S1b A0, A1, (A2) Remaining Switches RS GND 3 V +5 V RS tOFF(RS) DG42 DG429 Db, D VO V- WR 50% 0 V 300 W 35 pF VO 80% Switch Output 0V -15 V Figure 8. Reset Turn-Off Time tOFF(RS) +15 V V+ A0, A1, (A2) Rg S RS D IN Vg VO OFF EN ON OFF DVO VO CL 1 nF 3V GND 2.4 V WR V- DVO is the measured voltage error due to charge injection. The charge in coulombs is Q = CL x DVO -15 V Figure 9. Charge Injection 10 Siliconix S-56532--Rev. H, 19-Jan-98 DG428/429 Detailed Description Applications The internal structure of the DG428/DG429 includes a 5-V logic interface with input protection circuitry followed by a latch, level shifter, decoder and finally the switch constructed with parallel n- and p-channel MOSFETs (see Figure 1). Bus Interfacing The input protection on the logic lines A0, A1, A2, EN and control lines WR, RS shown in Figure 1 minimizes susceptibility to ESD that may be encountered during handling and operational transients. The logic interface is a CMOS logic input with its supply voltage from an internal +5 V reference voltage. The output of the input inverter feeds the data input of a D type latch. The level sensitive D latch continuously places the DX input signal on the QX output when the WR input is low, resulting in transparent latch operation. As soon as WR returns high the latch holds the data last present on the Dn input, subject to the "Minimum Input Timing Requirements" table. Following the latches the Qn signals are level shifted and decoded to provide proper drive levels for the CMOS switches. This level shifting ensures full on/off switch operation for any analog signal level between the V+ and V- supply rails. The EN pin is used to enable the address latches during the WR pulse. It can be hard wired to the logic supply or to V+ if one of the channels will always be used (except during a reset) or it can be tied to address decoding circuitry for memory mapped operation. The RS pin is used as a master reset. All latches are cleared regardless of the state of any other latch or control line. The WR pin is used to transfer the state of the address control lines to their latches, except during a reset or when EN is low (see Truth Tables). Siliconix S-56532--Rev. H, 19-Jan-98 The DG428/DG429 minimize the amount of interface hardware between a microprocessor system bus and the analog system being controlled or measured. The internal TTL compatible latches give these multiplexers write-only memory, that is, they can be programmed to stay in a particular switch state (e.g., switch 1 on) until the microprocessor determines it is necessary to turn different switches on or turn all switches off (see Figure 10). The input latches become transparent when WR is held low; therefore, these multiplexers operate by direct command of the coded switch state on A2, A1, A0. In this mode the DG428 is identical to the popular DG408. The same is true of the DG429 versus the popular DG409. During system power-up, RS would be low, maintaining all eight switches in the off state. After RS returned high the DG428 maintains all switches in the off state. When the system program performs a write operation to the address assigned to the DG428, the address decoder provides a CS active low signal which is gated with the WRITE (WR) control signal. At this time the data on the DATA BUS (that will determine which switch to close) is stabilizing. When the WR signal returns to the high state, (positive edge) the input latches of the DG428 save the data from the DATA BUS. The coded information in the A0, A1, A2 and EN latches is decoded and the appropriate switch is turned on. The EN latch allows all switches to be turned off under program control. This becomes useful when two or more DG428s are cascaded to build 16-line and larger multiplexers. 11 DG428/429 Applications (Cont'd) +15 V V+ Data Bus S1 15 V Analog Inputs A0, A1, A2, EN DG428 Processor System Bus RS RESET +5 V S8 WRITE WR D Address Bus V- Analog Output Address Decoder - 15 V Figure 10. Bus Interface 12 Siliconix S-56532--Rev. H, 19-Jan-98