DOCUMENT NUMBER NCD-64B4-02
SLP-2 Series
Multi-Mode
STTM CONNECTOR PLUG
TECHNICAL SPECIFICATIONS
Seiko Instruments Inc.
Components Sales Dept.
8, Nakase 1-Chome
Mihama-ku, Chiba-shi, Chiba-ken
261 JAPA N
Telephone : 043-211-1214
-1215
Facsimile : 043-211-8035
SLP-2 Series Multi-Mode STTM CONNECTOR PLUG
TECHNICAL SPECIFICATIONS
Document Number NCD-64B4-02
NAE12D01 February.1991
39052-2273-01 September.1991
39055-1015-01 October.1993
NCD-4oB6-01 October.1994
NCD-4oB7-01 October.1994
NCD-64B4-01 April.1996
NCD-64B4-02 September.1996
Copyright 1991, 1993, 1994, 1996 by Seiko Instruments Inc.
All right reserved.
The information contained herein shall not reproduced or disclosed to any third party
without the express written consent of SII.
The Specifications contained herein are subject to change without notice.
SIIis a trademark of Seiko Instruments Inc.
STis a registered tredemark of AT&T Technologies.
Kevleris a registered tredemark of E.I. du pont de Nemours & Company Inc.
Please address any questions, comments, and suggestions to:
Seiko Instruments USA Inc.
Electronics Components Division
2990 West Lomita Boulevard
Torrance, CA 90505, U.S.A.
Phone: 310-517-7780
Fax: 310-517-7792
Seiko Instruments GmbH
OFC Division
Siemensstraße 9b
D-63263 Neu-Isenburg, Germany
Phone: 06102-297-0
Fax: 06102-297-211
Seiko Instruments (H.K.) Ltd.
Sales Department
4th & 5th Floor, Wyler Center 2
200 Tai Lin Pai Road, Kwai Chung
N.T., Kowloon, Hong Kong
Phone: 852-2421-8611
Fax: 852-2480-5479
Seiko Instruments Taiwan Inc.
Sales Department
5F-1, No.99, Sec. 2, Chung Shan
Rd.
Taipei 104, Taiwan, R.O.C.
Phone: 02-563-5001, 523-5111
Fax: 02-521-9519
Seiko Instruments Singapore pte. Ltd.
2, Marsiling Lane,
Woodlands New Town,
Singapore, 2573, Singapore
Phone: 65-2691370
Fax: 65-2699729
ii
TABLE OF CONTENTS
Section Page
1. PROVISION 1
1.1 Application Limit 1
2. PARTS NUMBER 1
3. GENERAL SPECIFICATIONS 2
3.1 Parts and Materials 2
3.2 Physical Dimensions 2
3.3 General Tolerances 2
4. PACKING 3
Table
Table 1 Parts Number 1
Table 2 Parts and Materials 2
Table 3 Parts and Materials ( Main body ) 2
Table 4 General Tolerance 2
Figure
Figure 1 SLP-2 Connector 4
Figure 2 SLP-2 Connector ( PD Type ) 5
Figure 3 to 9 Part Dimensions 6
iii
iv
1. PROVISION
1.1 Application Limit
These specifications apply to the SLP-2 Multi-Mode STTM CONNECTOR PLUG supplied
by SII.
2. PARTS NUMBER
Parts Number of the Connector is Shown in Table 1.
Table 1 Parts Number
1
3. GENERAL SPECIFICATIONS
3.1 Parts and Materials
Parts and the materials are shown in Table 2 to 3.
Table 2 Parts and materials
No. Part Name Q'ty Material Notes
①Main body 1See Table 3 - -
➁Kevler crimping ring 1Aluminum alloy - -
③Hood ( for φ3.0mm cord) ( 1 ) Synthetic Rubber According to Table 1, Color : Black
➃Hood ( for φ0.9mm cord) ( 1 ) Synthetic Rubber According to Table 1, Color : Black
➄Cap 1 PVC Color : Black
Table 3 Parts and materials (Main body )
No. Part Name Q'ty Material Notes
⑥Ferrule 1Zirconia Ceramics - -
⑦Shell 1Zinc Die-cast Nickel Plating
⑧Byyonet 1Zinc Die-cast Nickel Plating
⑨Spring 1Stainless Steel - -
➉C-Ring 1Stainless Steel - -
3.2 Physical Dimensions
Figure 1 to 2 shows the assembled state of SLP-2.
Figure 3 to 9 show the part dimension.
3.3 General Tolerances
Permissible deviation in dimensions without tolerance indication is in accordance with
JIS B 0405 class m, as shown in Table 4.
Table 4 General tolerance (JIS B 0405 class m)
Basic size step (mm)
Over Under Permissible deviation (mm)
0.5 3
36
630
30 120
±0.1
±0.1
±0.2
±0.3
2
4. PACKING
The product is packed to prevent damage during shippment.
3
note.1: This drawing does not include Caps. Unit: mm
Figure 1 SLP-2 CONNECTOR
4
note.1: This drawing does not include Caps. Unit: mm
Figure 2 SLP-2 CONNECTOR ( PD Type )
5
Unit: mm
Figure 3 ①Main body
note . End curve offset = 0.05 mm or less. ( Pre-dome )
Unit: mm
Figure 4 ①Main body ( PD Type )
6
note . End curve offset = 0.05 mm or less. ( Pre-dome )
Unit: mm
Figure 5 ①Main body ( PD rough spec. Type )
Unit: mm
Figure 6 ➁Kevler crimping ring
7
Unit: mm
Figure 7 ③Hood
Unit: mm
Figure 8 ➃Hood
Unit: mm
Figure 9 ➄Cap
8
