DOCUMENT NUMBER NCD-64B4-02 SLP-2 Series S TTM Multi-Mode CONNECTOR PLUG TECHNICAL SPECIFICATIONS Seiko Instruments Inc. Components Sales Dept. 8, Nakase 1-Chome Mihama-ku, Chiba-shi, Chiba-ken 261 JAPAN Telephone : 043-211-1214 -1215 Facsimile : 043-211-8035 SLP-2 Series Multi-Mode STTM CONNECTOR PLUG TECHNICAL SPECIFICATIONS Document Number NCD-64B4-02 NAE12D01 39052-2273-01 39055-1015-01 NCD-4oB6-01 NCD-4oB7-01 February.1991 September.1991 October.1993 October.1994 October.1994 NCD-64B4-01 NCD-64B4-02 April.1996 September.1996 Copyright 1991, 1993, 1994, 1996 by Seiko Instruments Inc. All right reserved. The information contained herein shall not reproduced or disclosed to any third party without the express written consent of SII. The Specifications contained herein are subject to change without notice. SII is a trademark of Seiko Instruments Inc. S T is a registered tredemark of AT&T Technologies. Kevler is a registered tredemark of E.I. du pont de Nemours & Company Inc. Please address any questions, comments, and suggestions to: Seiko Instruments USA Inc. Seiko Instruments GmbH Electronics Components Division 2990 West Lomita Boulevard Torrance, CA 90505, U.S.A. Phone: 310-517-7780 Fax: 310-517-7792 OFC Division Siemensstrae 9b D-63263 Neu-Isenburg, Germany Phone: 06102-297-0 Fax: 06102-297-211 Seiko Instruments (H.K.) Ltd. Seiko Instruments Taiwan Inc. Sales Department 4th & 5th Floor, Wyler Center 2 200 Tai Lin Pai Road, Kwai Chung N.T., Kowloon, Hong Kong Phone: 852-2421-8611 Fax: 852-2480-5479 Sales Department 5F-1, No.99, Sec. 2, Chung Shan Rd. Taipei 104, Taiwan, R.O.C. Phone: 02-563-5001, 523-5111 Fax: 02-521-9519 Seiko Instruments Singapore pte. Ltd. 2, Marsiling Lane, Woodlands New Town, Singapore, 2573, Singapore Phone: 65-2691370 Fax: 65-2699729 ii TABLE OF CONTENTS Section 1. 1.1 Page PROVISION 1 Application Limit 1 2. PARTS NUMBER 1 3. GENERAL SPECIFICATIONS 2 3.1 Parts and Materials 2 3.2 Physical Dimensions 2 3.3 General Tolerances 2 4. PACKING 3 Table Table 1 Parts Number 1 Table 2 Parts and Materials 2 Table 3 Parts and Materials ( Main body ) 2 Table 4 General Tolerance 2 Figure Figure 1 SLP-2 Connector 4 Figure 2 SLP-2 Connector ( PD Type ) 5 Part Dimensions 6 Figure 3 to 9 iii iv 1. PROVISION 1.1 Application Limit These specifications apply to the SLP-2 Multi-Mode STTM CONNECTOR PLUG supplied by SII. 2. PARTS NUMBER Parts Number of the Connector is Shown in Table 1. Table 1 Parts Number 1 3. GENERAL SPECIFICATIONS 3.1 Parts and Materials Parts and the materials are shown in Table 2 to 3. Table 2 Parts and materials No. Part Name Main body Q'ty 1 Material See Table 3 Notes -- 1 Aluminum alloy -- Kevler crimping ring Hood ( for 3.0mm cord) ( 1 ) Synthetic Rubber According to Table 1, Color : Black Hood ( for 0.9mm cord) ( 1 ) Synthetic Rubber According to Table 1, Color : Black Cap 1 PVC Color : Black Table 3 Parts and materials (Main body ) No. Part Name Q'ty Material Notes Ferrule 1 Zirconia Ceramics Shell 1 Zinc Die-cast Nickel Plating Byyonet 1 Zinc Die-cast Nickel Plating Spring 1 Stainless Steel -- C-Ring 1 Stainless Steel -- -- 3.2 Physical Dimensions Figure 1 to 2 shows the assembled state of SLP-2. Figure 3 to 9 show the part dimension. 3.3 General Tolerances Permissible deviation in dimensions without tolerance indication is in accordance with JIS B 0405 class m, as shown in Table 4. Table 4 General tolerance (JIS B 0405 class m) Basic size step (mm) Over Under Permissible deviation (mm) 0.5 3 0 . 1 3 6 0 . 1 6 30 0 . 2 30 120 0 . 3 2 4. PACKING The product is packed to prevent damage during shippment. 3 note.1: This drawing does not include Caps. Unit: mm Figure 1 SLP-2 CONNECTOR 4 note.1: This drawing does not include Caps. Unit: mm Figure 2 SLP-2 CONNECTOR ( PD Type ) 5 Unit: mm Figure 3 Main body note . End curve offset = 0.05 mm or less. ( Pre-dome ) Unit: mm Figure 4 Main body ( PD Type ) 6 note . End curve offset = 0.05 mm or less. ( Pre-dome ) Unit: mm Figure 5 Main body ( PD rough spec. Type ) Unit: mm Figure 6 Kevler crimping ring 7 Unit: mm Figure 7 Hood Unit: mm Figure 8 Hood Unit: mm Figure 9 Cap 8