DESCRIPTION
HyperX HX321LS11IB2K2/16 is a kit of two 1G x 64-bit (8GB)
DDR3L-2133 CL11 SDRAM (Synchronous DRAM) 2Rx8, low
voltage, memory modules, based on sixteen 512M x 8-bit DDR3
FBGA components per module. Total kit capacity is 16GB.
Each module kit has been tested to run at DDR3L-2133 at a
low latency timing of 11-12-13 at 1.35V or 1.5V. Additional
timing parameters are shown in the PnP Timing Parameters
section below. The JEDEC standard electrical and mechanical
specifications are as follows:
Document No. 480 7184-001.A00 09/19/14 Page 1
SPECIFICATIONS
selcyc 11)DDI(LC
Row Cycle Time (tRCmin) 44.22ns (min.)
Refresh to Active/Refresh 260ns (min.)
Command Time (tRFCmin)
Row Active Time (tRASmin) 31.875ns (min.)
Maximum Operating Power TBD W* @1.35V
0 - V 49gnitaR LU
Operating Temperature 0o C to 85o C
Storage Temperature -55o C to +100o C
*Power will vary depending on the SDRAM used.
HX321LS11IB2K2/16
16GB (8GB 1G x 64-Bit x 2 pcs.) DDR3L-2133
CL11 204-Pin SODIMM Kit
Continued >>
kingston.com/hyperx
PnP JEDEC TIMING PARAMETERS:
•DDR3-2133 CL11-12-13 @1.35V or 1.5V
•DDR3-1866 CL10-11-12 @1.35V or 1.5V
•DDR3-1600 CL9-9-10 @1.35V or 1.5V
Note: The PnP feature offers a range of speed and timing options to support
the widest variety of processors and chipsets. Your maximum speed will
be determined by your BIOS.
FEATURES
•JEDEC standard 1.35V and 1.5V
•VDDQ = 1.35V and 1.5V
•1066MHz fCK for 2133Mb/sec/pin
•8 independent internal bank
•Programmable CAS Latency: 15, 14, 13, 12, 11, 10, 9, 8, 7, 6
•Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
•8-bit pre-fetch
•Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or
MRS]
•Bi-directional Differential Data Strobe
•Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
•On Die Termination using ODT pin
•Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95 ° C
•Asynchronous Reset
•PCB : Height 1.180” (30.00mm), double sided component
Document No. 4807184-001.A00 Page 2
continued HyperX
MODULE DIMENSIONS
All Kingston products are tested to meet our published specifications. Some motherboards or system configurations may not operate at
the published HyperX memory speeds and timing settings. Kingston does not recommend that any user attempt to run their computers
faster than the published speed. Overclocking or modifying your system timing may result in damage to computer components.
FOR MORE INFORMATION, GO TO WWW.KINGSTON.COM/HYPERX
kingston.com/hyperx
