Features * 0.6 m Drawn Gate Length (0.5 m Leff) Sea-of-Gates Architecture with Triple-level Metal * 5.0V, 3.3V and 2.0V Operation including Mixed Voltages * On-chip Phase Locked Loop Available to Synthesize Frequencies up to 150 MHz and * * * * * Manage Chip-to-Chip Clock Skew Compiled (Gate Level) and Embedded (Custom) SRAMs, ROM, and CAMs Available PCI, SCSI and High Speed (250 MHz) Buffers Available Easy Alternative Sourcing of Existing ASIC, FPGA and PLD Designs Design-for-Test Methods, Including JTAG, Serial and Boundary Scan and ATPG High Output Drive Capability: Up to 48 mA with Slew Rate Control ASIC Description Atmel's next generation ATL60 Series CMOS ASICs are fabricated using a 0.6m drawn gate, oxide isolated, triple-level metal process. Extensive cell libraries are available and support the major CAD software tools. As with all Atmel ASIC families, customer involvement and satisfaction is integral to all steps of the design flow. A variety of Design for Testability techniques are supported by the libraries, and a wide range of packaging options are available. The ATLS version utilizes a fine pitch staggered row on bond pads to achieve the smallest die size possible for a given pad count. The ATLS60 is only available in a limited number of PQFP packages. ATL 60 and ATLS60 Series Table 1. ATL60 Array Organization Device Number Raw Gates Routable Gates Max Pin Count Max I/O Pins Gate(1) Speed ATL60/4 4,000 3,000 44 36 200 ps ATL60/15 15,000 10,000 68 60 200 ps ATL60/25 25,000 16,900 84 76 200 ps ATL60/40 38,000 25,400 100 92 200 ps ATL60/60 58,000 34,600 120 112 200 ps ATL60/85 86,000 51,900 144 136 200 ps ATL60/110 110,000 65,900 160 152 200 ps ATL60/150 149,000 89,300 184 176 200 ps ATL60/200 195,000 116,900 208 200 200 ps ATL60/235 232,000 139,500 226 218 200 ps ATL60/300 301,000 181,000 256 248 200 ps ATL60/435 430,000 260,000 304 296 200 ps ATL60/550 545,000 288,000 340 332 200 ps ATL60/700 693,000 363,000 380 372 200 ps ATL60/870 870,000 456,000 424 416 200 ps ATL60/1100 1,119,000 590,000 480 472 200 ps Note: 1. Nominal two input NAND gate with a fanout of 2 at 5.0 volts Rev. 0388D-ASIC-07/02 1 ATLS60 Array Organization Note: Device Number Raw Gates Routable Gates Max Pin Count Max I/O Pins Gate(1) Speed ATLS60/80 12,500 8,000 80 72 200 ps ATLS60/100 20,400 13,000 100 92 200 ps ATLS60/120 30,200 17,500 120 112 200 ps ATLS60/144 44,600 26,000 144 136 200 ps ATLS60/160 55,300 32,500 160 152 200 ps ATLS60/208 96,500 57,000 208 200 200 ps ATLS60/225 113,500 67,500 225 217 200 ps ATLS60/256 148,200 88,000 256 248 200 ps 1. Nominal two-input NAND gate with a fanout of 2 at 5.0 volts Design Design Systems Supported Atmel supports the major software systems for design with complete macro cell libraries, as well as utilities for checking the netlist and accurate pre-route delay simulations. Table 2. Design Systems Supported System Tools (R) 2 TM Version Cadence Design Systems, Inc. Opus - Schematic and Layout NC VerilogTM - Verilog Simulator PearlTM - Static Path Verilog-XLTM - Verilog Simulator BuildGatesTM - Synthesis (Ambit) 4.46 3.3-s008 4.3-s095 3.3-s006 4.0-p003 Mentor Graphics(R) ModelSim(R) - Verilog and VHDL (VITAL) Simulator Leonardo SpectrumTM - Logic Synthesis 5.5e 2001.1d SynopsysTM Design CompilerTM - Synthesis DFT Compiler - 1-Pass Test Synthesis BSD Compiler - Boundary Scan Synthesis TetraMax(R) - Automatic Test Pattern Generation PrimeTimeTM - Static Path VCSTM - Verilog Simulator Floorplan ManagerTM 01.01-SP1 01.08-SP1 01.08-SP1 01.08 01.08-SP1 5.2 01.08-SP1 Novas Software, Inc. Debussy(R) 5.1 Silicon PerspectiveTM First Encounter(R) v2001.2.3 ATL60 and ATLS60 Series 0388D-ASIC-07/02 ATL60 and ATLS60 Series Design Flow Atmel provides three methods for implementing an ASIC design while maintaining the same basic design flow for each method. This flow involves both the customer and Atmel at all critical review and acceptance steps, as shown on the following page. Database Acceptance occurs when Atmel receives and accepts the complete design database. Upon completion of this critical step, Atmel performs physical place-and-route. Functional and timing simulations are performed, based on the physical design, including the generation of a back annotation report to provide the customer with the most accurate timing information available. Final Design Review is the last step of the design flow prior to generation of masks. After this acceptance step is completed, masks are generated and released, and prototype parts in ceramic packages are delivered. 3 0388D-ASIC-07/02 ASIC Design Flow (2) Kickoff Meeting Customer Atmel Synthesis, Translation or Conversion Atmel Customer Database Submission for Underlayer Atmel Customer Underlayer Acceptance and Tapeout Atmel Final Database Submission Atmel Customer (1) Customer (2) Database Acceptance Physical Design and Verification (1) Atmel Atmel (2) Customer Final Design Review Customer Prototype Delivery Notes: 4 (1) (1) Customer 1) Performed by the customer or optionally by Atmel 2) ISO 9001/QS9000 Milestone Atmel (2) Rev.2.3-04/02 ATL60 and ATLS60 Series 0388D-ASIC-07/02 ATL60 and ATLS60 Series Pin Definition Requirements Within the Physical Design step (i.e., layout), certain restrictions apply during pin definition. The corner pins on each die are reserved and programmable for power and ground only. All other buffer pins are fully programmable as input, output, bidirectional, clockinto-array, power, or ground. Design Options Logic Synthesis Atmel can accept Register Transfer Level (RTL) designs for VHDL (MIL-STD-454, IEEE STD 1076) or Verilog-HDL format. Atmel fully supports Synopsys for VHDL simulation as well as synthesis. VHDL or Verilog-HDL is Atmel's preferred method of performing an ASIC design. ASIC Design Translation Atmel has successfully translated dozens of existing designs from most major ASIC vendors into our ASICs. These designs have been optimized for speed and gate count and modified to add logic or memory, or replicated for a pin-for-pin compatible, drop-in replacement. FPGA and PLD Conversions Atmel has successfully translated existing FPGA/PLD designs from most major vendors into our ASICs. There are four primary reasons to convert from an FPGA/PLD to an ASIC. Conversion of high-volume devices (over 10,000 units) for a single or combined design is cost effective. Performance can often be optimized for speed or power consumption. Several FPGA/PLDs can be combined onto a single chip to minimize cost while reducing on-board space requirements. Finally, in situations where an FPGA/PLD was used for fast cycle time prototyping, an ASIC may provide a lower cost answer for long-term volume production. 5 0388D-ASIC-07/02 ATL60 Series Cell Library Atmel's ATL60 Series ASICs make use of an extensive library of cell structures, including logic cells, buffers and inverters, multiplexers, decoders and I/O options. Soft macros are also available. The ATL60 Series PLL operates at frequencies of up to 150 MHz with minimal phase error and jitter, making it ideal for frequency synthesis of high-speed on-chip clocks and chip-to-chip synchronization. Output buffers are programmable to meet the voltage and current requirements of both PCI and SCSI. These cells are characterized by use of SPICE modeling at the transistor level, with performance verified on manufactured test arrays. Characterization is performed over the military temperature and voltage ranges to ensure that the simulation accurately predicts the performance of the finished product. Table 3. Cell Index Site Count(1) Signal Name Description ADD3X One-bit full adder with buffered outputs AND2 2-input AND 2 AND2H 2-input AND - High-drive 3 AND3 3-input AND 3 AND3H 3-input AND - High-drive 4 AND4 4-input AND 3 AND4H 4-input AND - High-drive 4 AND5 5-input AND 5 AOI22 2-input AND into 2-input NOR 2 AOI22H 2-input AND into 2-input NOR - High-drive 4 AOI222 Two 2-input ANDs into 2-input NOR 4 AOI222H Two 2-input ANDs into 2-input NOR - High-drive 8 AOI2223 Three 2-input ANDs into 3-input NOR 4 AOI2223H Three 2-input ANDs into 3-input NOR - High-drive 7 AOI23 2-input AND into 3-input NOR 2 BUF1 1x Buffer 2 BUF2 2x Buffer 2 BUF2T 2x Tristate Bus Driver with Active-high Enable 4 BUF2Z 2x Tristate Bus Driver with Active-low Enable 4 BUF3 3x Buffer 3 BUF4 4x Buffer 3 BUF8 8x Buffer 5 BUF12 12x Buffer 8 BUF16 16x Buffer 10 CLA7X 7-input Carry Lookahead 5 DEC4 2:4 Decoder 7 DEC4N 2:4 Decoder with Active-low Enable 9 6 10 ATL60 and ATLS60 Series 0388D-ASIC-07/02 ATL60 and ATLS60 Series Table 3. Cell Index (Continued) Site Count(1) Signal Name Description DEC8N 3:8 Decoder with Active-low Enable DFF D Flip-flop D Flip-flop with Asynchronous Clear and Preset with Complementary Outputs 16 DFFBCPX D Flip-flop with Asynchronous Set and Reset with Complementary Outputs 16 DFFBSRX DFFC D Flip-flop with Asynchronous Clear 9 DFFR D Flip-flop with Asynchronous Reset 11 DFFS D Flip-flop with Asynchronous Set DFFSR D Flip-flop with Asynchronous Set and Reset DLY1500 Delay Buffer 1.5 ns 6 DLY2000 Delay Buffer 2.1 ns 10 DLY6000 Delay Buffer 6.0 ns 24 DSS Set Scan Flip-flop 11 DSSBCPY Set Scan Flip-flop with Clear and Preset 16 DSSBR Set Scan Flip-flop with Reset 13 DSSBS Set Scan Flip-flop with Set 13 DSSR Set Scan D Flip-flop with Reset 13 DSSS Set Scan D Flip-flop with Set 12 DSSSR Set Scan D Flip-flop with Set and Reset 14 INV1 1x Inverter 1 INV1D Dual 1x Inverters 2 INV1Q Quad 1x Inverters 4 INV1TQ Quad Tristate Inverter 7 INV2 2x Inverter 2 INV2T 2x Tristate Inverter with Active-high Enable 3 INv3h 3x Inverter 2 INV4 4x Inverter 2 INV8 8x Inverter 4 INV10 10x Inverter 8 JKF JK Flip-flop 10 Clear Preset JK Flip-flop with Asynchronous Clear and Preset and Complementary Outputs 16 JKFBCPX JKFC JK Flip-flop with Asynchronous Clear 12 LAT LATCH 4 LATBG LATCH with Complementary Outputs and Inverted Gate Signal 6 LATBH LATCH with High-drive Complementary Outputs 7 24 8 9 12 7 0388D-ASIC-07/02 Table 3. Cell Index (Continued) Site Count(1) Signal Name Description LATR LATCH with Reset 4 LATS LATCH with Set 6 LATSR LATCH with Set and Reset 8 LSCC Voltage Level Shifter 4 LSISO Voltage Level Shifter with Power Supply Isolation Function MUX2 2:1 MUX 4 MUX2H 2:1 MUX - High-drive 5 MUX2I 2:1 MUX with Inverted Output 3 MUX2IH 2:1 MUX with Inverted Output - High-drive 4 MUX2N 2:1 MUX with Active-low Enable 4 MUX2NQ Quad 2:1 MUX with Active-low Enable 18 MUX2Q Quad 2:1 MUX 14 MUX3I 3:1 MUX with Inverted Output 6 MUX3IH 3:1 MUX with Inverted Output - High-drive 8 MUX4 4:1 MUX 9 MUX4X 4:1 MUX with Transmission Gate Data Inputs 10 MUX4XH 4:1 MUX with Transmission Gate Data Inputs - High-drive 10 MUX5H 5:1 MUX - High-drive 14 MUX8 8:1 MUX 18 MUX8N 8:1 MUX with Active-low Enable 20 MUX8XH 8:1 MUX with Transmission Gate Data Inputs - High-drive 18 NAN2 2-input NAND 2 NAN2D Dual 2-input NAND 3 NAN2H 2-input NAND - High-drive 2 NAN3 3-input NAND 2 NAN3H 3-input NAND - High-drive 3 NAN4 4-input NAND 3 NAN4H 4-input NAND - High-drive 4 NAN5 5-input NAND 5 NAN5H 5-input NAND - High-drive 6 NAN6 6-input NAND 6 NAN6H 6-input NAND - High-drive 7 NAN8 8-input NAND 7 NAN8H 8-input NAND - High-drive 7 NOR2 2-input NOR 2 NOR2D Dual 2-input NOR 3 8 12 ATL60 and ATLS60 Series 0388D-ASIC-07/02 ATL60 and ATLS60 Series Table 3. Cell Index (Continued) Site Count(1) Signal Name Description NOR2H 2-input NOR - High-drive 2 NOR3 3-input NOR 2 NOR3H 3-input NOR - High-drive 3 NOR4 4-input NOR 3 NOR4H 4-input NOR - High-drive 4 NOR5 5-input NOR 5 NOR8 8-input NOR 7 OAI22 2-input OR into 2-input NAND 2 OIA22H 2-input OR into 3-input NAND - High-drive 4 OAI222 Two 2-input ORs into 2-input NAND 2 OAI222H Two 2-input ORs into 2-input NAND - High-drive 4 OAI22224 Four 2-input ORs into 4-input NAND 6 OAI23 2-input OR into 3-input NAND 3 ORR2 2-input OR 2 ORR2H 2-input OR - High-drive 3 ORR3 3-input OR 3 ORR3H 3-input OR - High-drive 4 ORR4 4-input OR 3 ORR4H 4-input OR - High-drive 4 ORR5 5-input OR 5 XNR2 2-input Exclusive NOR 4 XNR2H 2-input Exclusive NOR - High-drive 4 XOR2 2-input Exclusive OR 4 XOR2H 2-input Exclusive OR - High-drive 4 Note: 1. A single ATL60 routing site contains four transistors, two N-channel and two P-channel, aligned in columns. The number of sites used per gate varies according to the specific isolation and power requirements. Percent utilization varies from 50% to 70%, with more accurate utilization figures generated by DoubleCheckTM, the netlist checker. 9 0388D-ASIC-07/02 Table 4. CMOS Input Interface Characteristics Interface Logic High Logic Low Switchpoint CMOS 3.5V Minimum 1.5V Maximum VDD /2 Typical TTL 2.0V Minimum 0.8V Maximum 1.4V Typical Table 5. Absolute Maximum Ratings(1) Operating Temperature -55C to +125C Storage Temperature -65C to +150C Voltage on Any Pin with Respect to Ground -2.0V to +7.0V(2) Maximum Operating Voltage 6.0V Notes: 1. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2. Minimum voltage is -0.6V DC, which may undershoot to -2.0V for pulses of less than 20 ns. Maximum output pin voltage is VDD + 0.75V dc, which may overshoot to +7.0V for pulses of less than 20 ns. Table 6. 5.0-volt DC Characteristics Applicable over recommended operating range from Ta = -55C to +125C, VDD = 4.5V to 5.5V (unless otherwise noted) Symbol Parameter Test Condition IIH Input Leakage High VIN = VDD, VDD = 5.5V IIL Input Leakage Low (no pull-up) 40K pull-up VIN = VSS, VDD = 5.5V VIN = VSS, VDD = 5.5V IOZ Output Leakage (no pull-up) VIN = VDD or VSS, VDD = 5.5V IOS Output Short Circuit Current (3x buffer)(1) VDD = 5.5V, VOUT = VDD VDD = 5.5V, VOUT = VSS VIL TTL Input Low Voltage VIL CMOS Input Low Voltage VIH TTL Input High Voltage VIH CMOS Input High Voltage VT TTL Switching Threshold CMOS Switching Threshold VDD = 5.0V, 25C VDD = 5.0V, 25C 1.4 2.4 IOL = as rated VDD = 4.5V 0.2 VOL Output Low Voltage Output buffer has 12 stages of drive capability with 2 mA IOL per stage VOH Output High Voltage Output buffer has 12 stages of drive capability with -2 mA IOH per stage IOH = as rated VDD = 4.5V Note: 10 Min Typ Max Units 10 A -10 -100 -15 A -10 10 A 66 mA mA -66 0.8 V 0.3 x VDD V 2.0 V 0.7 x VDD V 0.7 x VDD 4.2 V V 0.4 V V 1. This is the specification for the 3x buffer. Output short circuit current for other outputs will scale accordingly. Not more than one output shorted at a time, for a maximum of one second, is allowed. ATL60 and ATLS60 Series 0388D-ASIC-07/02 ATL60 and ATLS60 Series Table 7. 3.3-volt DC Characteristics Applicable over recommended operating range from Ta = -55C to +125C, VDD = 2.7V to 3.6V (unless otherwise noted) Symbol Parameter Test Condition Min Typ Max Units IIH Input Leakage High VIN = VDD, VDD = 3.6V 5 A IIL Input Leakage Low (no pull-up) Max R pull-up (U31) VIN = VSS, VDD = 3.6V VIN = VSS, VDD = 3.6V -5 -25 -3 IOZ Output Leakage (no pull-up) VIN = VDD or VSS, V DD = 3.6 V -5 5 IOS Output Short Circuit Current (8 x buffer)(1) VDD = 3.6 V, VOUT = VDD VDD = 3.6 V, VOUT = VSS VIL CMOS Input Low Voltage VIH CMOS Input High Voltage VT CMOS Switching Threshold VDD = 3.0V, 25C VOL Output Low Voltage Output buffer has 12 stages of drive capability with 1 mA IOL per stage. IOL = as rated VDD = 2.7V VOH Output High Voltage Output buffer has 12 stages of drive capability with -1 mA IOH per stage. IOH = as rated VDD = 2.7V A A 88 mA mA -88 0.3 x VDD V 0.7 x V DD V 1.5 V 0.4 0.7 x V DD V 4.2 V Table 8. 2.0-volt DC Characteristics Applicable over recommended operating range from Ta = 0C to +70C, VDD = 1.8V to 2.2V (unless otherwise noted) Symbol Parameter Test Condition IIH Input Leakage High VIN = VDD, VDD = 2.2V IIL Input Leakage Low (no pull-up) Max R pull-up (U31) VIN = VSS, VDD = 2.2V VIN = VSS, VDD = 2.2V IOZ Output Leakage (no pull-up) VIN = VDD or VSS, VDD = 2.2V IOS Output Short Circuit Current (8 x buffer)(1) VDD = 2.2V, VOUT = V DD VDD = 2.2V, VOUT = V SS VIL CMOS Input Low Voltage VIH CMOS Input High Voltage VT CMOS Switching Threshold VOL Output Low Voltage Output buffer has 12 stages of drive capability with 0.5 mA IOL per stage. IOL as rated VDD = 1.8V VOH Output High Voltage Output buffer has 12 stages of drive capability with -0.5 mA IOH per stage. IOH as rated VDD = 1.8V Note: Min Typ Max Units 5 A -5 -15 -2 A A -5 5 A 40 mA mA -40 0.2 x VDD 0.8 x VDD V V 0.5xVDD V 0.2 x VDD 0.8 x VDD V V This is the specification for the 8x buffer. Output short circuit current for other outputs will scale accordingly. Not more than one output shorted at a time, for a maximum of one second, is allowed. 11 0388D-ASIC-07/02 Table 9. I/O Buffer DC Characteristics Symbol Parameter Test Condition Min Typ Max Units CIN Capacitance, Input Buffer (die) 5.0V, 3.3V, 2.0V 2.4 pF COUT Capacitance, Output Buffer (die) 5.0V, 3.3V, 2.0V 5.6 pF CI/O Capacitance, Bidirectional 5.0V, 3.3V, 2.0V 6.6 pF 1.8 3.0 Schmitt Trigger V+ TTL Positive Threshold CMOS Positive Threshold 25C, 5.0V 25C, 5.0V V- TTL Negative Threshold CMOS Negative Threshold 25C, 5.0V 25C, 5.0V V TTL Hysteresis CMOS Hysteresis V+ V V 1.0 2.0 V V 25C, 5.0V 25C, 5.0V 0.8 1.0 V V CMOS Positive Threshold 25C, 3.3V 1.8 V- CMOS Negative Threshold 25C, 3.3V V CMOS Hysteresis 25C, 3.3V I/O Buffers Design for Testability 0.8 1.5 2.0 3.5 1.0 * Programmable output drive 2 to 24 mA IOL; -2 to -24 mA IOH at 5.0 volts 1 to 12 mA IOL; -1 to -12 mA IOH at 3.3 volts * Programmable slew rate control * Built-in configurable test logic 2.3 V 1.3 V 0.5 V Atmel supports a wide range of Design for Testability techniques to improve the percentage of a design that can be fully tested. By achieving a high degree of testability, a designer can reduce design and prototype debug time, minimize production test time, and improve board- and system-level test and diagnostic capability. Synopsys Test Compiler software is fully supported by Atmel. By using this system during design, the computer will create and add a set of scan chains to the design, and test vectors will be generated to provide greater than 95% fault coverage. This method requires only one or two added pins for Test Enable and Test Mode. This is the easiest and least expensive method of designing testability into an ASIC design. Ad hoc means of increasing testability of an ASIC are also available. Partitioning, memory array isolation, and test point insertion are encouraged and supported by the ATL60 Series ASICs. Atmel also encourages the inclusion of Built-In Self-Test (BIST) techniques whenever possible. Each of these methods is discussed in detail in the Atmel CMOS ASIC Design Manual. In addition to all of the above, the ATL60 Series ASICs also support the Joint Test Action Group (JTAG) boundary scan architecture and Test Access Port (TAP) requirements. The required soft and hard macros to implement IEEE 1149.1-compliant architecture are available in Atmel's cell library. Use of JTAG architecture requires an additional four to five pins for test mode, data, and clock signals. 12 ATL60 and ATLS60 Series 0388D-ASIC-07/02 ATL60 and ATLS60 Series Advanced Packaging The ATL60 Series ASICs are offered in a wide variety of standard packages, including plastic and ceramic quad flatpacks, thin quad flatpacks, ceramic pin grid arrays and ball grid arrays. High-volume on-shore and off-shore contractors provide assembly and test for commercial product, with prototype capability in Colorado Springs. Custom package designs are also available as required to meet a customer's specific needs and are supported through Atmel's package design center. When a standard package cannot meet a customer's need, a package can be designed to precisely fit the application and to maintain the performance obtained in silicon. Atmel has delivered custom-designed packages in a wide variety of configurations. Table 10. Package Options (Partial List) Package Type Pin Count PQFP 44, 52, 64, 80, 100, 120, 128, 132, 144, 160, 184, 208, 240, 304 Power Quad 144, 160, 208, 240, 304 L/TQFP 32, 44, 48, 64, 80, 100, 120, 128, 144, 160, 176, 216 PLCC 20, 28, 32, 44, 52, 68, 84 CPGA 64, 68, 84, 100, 124, 144, 155, 180, 223, 224, 299, 391 CQFP 64, 68, 84, 100, 120, 132, 144, 160, 224, 340 PBGA 121, 169, 208, 217, 225, 240, 256, 272, 300, 304, 313, 316, 329, 352, 388, 420, 456 Super BGA 168, 204, 240, 256, 304, 352, 432, 560, 600 Low-profile Mini BGA 40, 48, 49, 56, 60, 64, 80, 81, 84, 96, 100, 108, 128, 132, 144, 160, 176, 192, 208, 224, 228 Chip-scale BGA 32, 36, 40, 48, 49, 56, 64, 81, 84, 100, 108, 121, 128, 144, 160, 169, 176, 192, 208, 224, 256, 288, 324 Flex-tape BGA 48, 49, 64, 80, 81, 84, 96, 100, 112, 132, 144, 156, 160, 180, 192, 196, 204, 208, 220, 225, 228, 256, 280 FCBGA* 416, 480, 564, 672, 788, 896, 960, 1032, 1152, 1157, 1292, 1357, 1413, 1500, 1517, 1557, 1677, 1728, 1932 Note: * These packages require a custom design substrate. 13 0388D-ASIC-07/02 Atmel Headquarters Atmel Operations Corporate Headquarters Memory 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 487-2600 Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland TEL (41) 26-426-5555 FAX (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimhatsui East Kowloon Hong Kong TEL (852) 2721-9778 FAX (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan TEL (81) 3-3523-3551 FAX (81) 3-3523-7581 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany TEL (49) 71-31-67-0 FAX (49) 71-31-67-2340 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France TEL (33) 2-40-18-18-18 FAX (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France TEL (33) 4-76-58-30-00 FAX (33) 4-76-58-34-80 Zone Industrielle 13106 Rousset Cedex, France TEL (33) 4-42-53-60-00 FAX (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland TEL (44) 1355-803-000 FAX (44) 1355-242-743 e-mail literature@atmel.com Web Site http://www.atmel.com (c) Atmel Corporation 2002. Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company's standard warranty which is detailed in Atmel's Terms and Conditions located on the Company's web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel's products are not authorized for use as critical components in life support devices or systems. Atmel(R) is a registered trademark and DoubleCheck TM is a trademark of Atmel. Cadence(R) is a registered trademark and Opus TM, NC Verilog TM, PearlTM , Verilog-XL TM and BuildGatesTM are trademarks of Cadence Design Systems, Inc.; Mentor Graphics (R) and ModelSim (R) are registered trademarks and Leonardo Spectrum TM is a trademark of Mentor Graphics; Design Compiler TM, PrimeTimeTM , VCS TM and Floorplan Manager TM are trademarks and Synopsys (R) and TetraMax (R) are registered trademarks of Synopsys; Debussy (R) is a registered trademark of Novas Software, Inc.; Silicon Perspective (R) and First Encounter (R) are registered trademarks of Silicon Perspective. Other terms and product names may be the trademarks of others. Printed on recycled paper. 0388D-ASIC-07/02