DESCRIPTION
The
µ
PG2310TK is a GaAs MMIC LNA for SDARS (Satellite Digital Audio Radio Services). High Gain and Low
Distortion suit to driver stage amplifier for Satellite Radio Antenna.
FEATURES
• High gain : GP = 27.0 dB TYP.
• Low distortion : OIP3 = +28.5 dBm TYP.
• 6-pin lead-less minimold package (1.5 × 1.1 × 0.55 mm)
APPLICATION
• Satellite Radio Antenna etc.
ORDERING INFORMATION
Part Number Order Number Package Marking Supplying Form
µ
PG2310TK-E2
µ
PG2310TK-E2-A 6-pin lead-less minimold
(1511 PKG) (Pb-Free) Note G4W • Embossed tape 8 mm wide
• Pin 1, 6 face the perforation side of the tape
• Qty 5 kpcs/reel
Note With regards to terminal solder (the solder contains lead) plated products (conventionally plated), contact
your nearby sales office.
Remark To order evaluation samples, contact your nearby sales office.
Part number for sample order:
µ
PG2310TK-A
Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge.
GaAs MMIC LOW NOISE AMPLIFIER FOR SATELLITE RADIO
GaAs INTEGRATED CIRCUIT
µ
PG2310TK
Document No. PG10576EJ01V0DS (1st edition)
Date Published August 2005 CP(K)
PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM
Pin No. Pin Name
1 VCC2/OUT
2 GND
3 VCC1
4 IN
5 GND
(T op View)
1
2
34
5
6
G4W
(T op View)
1
2
34
5
6
(Bottom View)
6
5
43
2
1
6 GND
ABSOLUTE MAXIMUM RATINGS (TA = +25°C, unless otherwise specified)
Parameter Symbol Ratings Unit
Supply Voltage VCC1, VCC2 +5.0 V
Input Power Pin −10 dBm
Total Power Dissipation Ptot 300 Note mW
Operating Ambient Temperature TA −45 to +85 °C
Storage Temperature Tstg −55 to +150 °C
Note Mounted on double-sided copper-clad 50 × 50 × 1.6 mm epoxy glass PWB, TA = +85°C
RECOMMENDED OPERATING RANGE
Parameter Symbol MIN. TYP. MAX. Unit
Operating Frequency fopt 2 320 2 340 2 360 MHz
Supply Voltage VCC1, VCC2 +2.7 +3.0 +3.3 V
Operating Ambient Temperature TA −45 +25 +85 °C
Data Sheet PG10576EJ01V0DS
2
µ
PG2310TK
ELECTRICAL CHARACTERISTICS (TA = +25°C, VCC1 = VCC2 = +3.0 V, ZO = 50 Ω, unless otherwise
specified)
Parameter Symbol Test Conditions MIN. TYP. MAX. Unit
Power Gain GP f = 2 340 MHz, Pin = −30 dBm 25.0 27.0 − dB
Noise Figure NF f = 2 340 MHz − 1.8 2.0 dB
Input Return Loss RLin f = 2 340 MHz, Pin = −30 dBm − 13 − dB
Output Return Loss RLout f = 2 340 MHz, Pin = −30 dBm − 15 − dB
Output 3rd Order Distortion
Intercept Point OIP3 f1 = 2 340 MHz, f2 = 2 340.1 MHz +26.5 +28.5 − dBm
Circuit Current Note ICC f = 2 340 MHz, Pin = −30 dBm − 30 35 mA
Note Please refer to following chart.
Circuit Current I
CC
(mA)
Supply Voltage V
CC
(V)
CIRCUIT CURRENT vs. SUPPLY VOLTAGE
40
35
30
25
20
15
2.5 2.6 2.7 2.8 2.9 3 3.1 3.2 3.3 3.53.4
Remark The graph indicates nominal characteristics.
Data Sheet PG10576EJ01V0DS 3
µ
PG2310TK
TEST CIRCUIT
IN
GND
V
CC
1
OUT
L1
2.2 nH
4
5
6
3
2
1
GND
GND
V
CC
2
L3
68 nH
C1
5.0 pF L2
3.3 nH
C3
0.1 F
µ
C2
0.1 F
µ
The application circuits and their parameters are for reference only and are not intended for use in actual design-ins.
Data Sheet PG10576EJ01V0DS
4
µ
PG2310TK
TYPICAL CHARACTERISTICS (TA = +25°C, unless otherwise specified)
40
30
20
10
0
–10
–20
–30
–40
–50
–60
–70
39
38
37
36
35
34
33
32
31
30
29
28
–30 –20 –10 0 10
Input Power (2 tones) P
in
(dBm)
OUTPUT POWER (2 tones), IM
3
(2 tones),
I
CC
vs. INPUT POWER (2 tones)
IM3
ICC VCC1 = VCC2 = +3.0 V
f1 = 2 340 MHz
f2 = 2 340.1 MHz
Pout
Circuit Current I
CC
(mA)
Output Power (2 tones) P
out
(dBm)
3rd Order Intermodulation Distortion (2 tones) IM
3
(dBm)
Remark The graph indicates nominal characteristics.
Data Sheet PG10576EJ01V0DS 5
µ
PG2310TK
PACKAGE DIMENSIONS
6-PIN LEAD-LESS MINIMOLD (1511 PKG) (UNIT: mm)
0.48±0.050.48±0.05
1.5±0.1
1.3±0.05
1.1±0.1
0.55±0.03
0.11
+0.1
–0.05
0.16±0.05
0.9±0.10.2±0.1
(Bottom View)
(Top View)
Data Sheet PG10576EJ01V0DS
6
µ
PG2310TK
RECOMMENDED SOLDERING CONDITIONS
This product should be soldered and mounted under the following recommended conditions. For soldering
methods and conditions other than those recommended below, contact your nearby sales office.
Soldering Method Soldering Conditions Condition Symbol
Infrared Reflow Peak temperature (package surface temperature) : 260°C or below
Time at peak temperature : 10 seconds or less
Time at temperature of 220°C or higher : 60 seconds or less
Preheating time at 120 to 180°C : 120±30 seconds
Maximum number of reflow processes : 3 times
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
IR260
Wave Soldering Peak temperature (molten solder temperature) : 260°C or below
Time at peak temperature : 10 seconds or less
Preheating temperature (package surface temperature) : 120°C or below
Maximum number of flow processes : 1 time
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
WS260
Partial Heating Peak temperature (terminal temperature) : 350°C or below
Soldering time (per side of device) : 3 seconds or less
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
HS350
Caution Do not use different soldering methods together (except for partial heating).
Data Sheet PG10576EJ01V0DS 7
µ
PG2310TK
4590 Patrick Henry Drive
Santa Clara, CA 95054-1817
Telephone: (408) 919-2500
Facsimile:
(
408
)
988-0279
Subject: Compliance with EU Directives
CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant
with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous
Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive
2003/11/EC Restriction on Penta and Octa BDE.
CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates
that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are
exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals.
All devices with these suffixes meet the requirements of the RoHS directive.
This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that
go into its products as of the date of disclosure of this information.
Restricted Substance
per RoHS Concentration Limit per RoHS
(values are not yet fixed) Concentration contained
in CEL devices
-A -AZ
Lead (Pb) < 1000 PPM Not Detected (*)
Mercury < 1000 PPM Not Detected
Cadmium < 100 PPM Not Detected
Hexavalent Chromium < 1000 PPM Not Detected
PBB < 1000 PPM Not Detected
PBDE < 1000 PPM Not Detected
If you should have any additional questions regarding our devices and compliance to environmental
standards, please do not hesitate to contact your local representative.
Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance
content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information
provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better
integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate
information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL
suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for
release.
In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to
customer on an annual basis.
See CEL Terms and Conditions for additional clarification of warranties and liability.
