TC4051,4052,4053BP/BF/BFT
2016-01-15
1
TOS HIB A CMO S Digit a l Int egr at ed Cir c uit Silicon M on o lith ic
TC4051BP, TC4051BF, TC4051BFT
TC4052BP, TC4052BF, TC4052BFT
TC4053BP, TC4053BF, TC4053BFT
TC4051B
Single 8-Channel Multiplexer/Demultiplexer
TC4052B
Differential 4-Channel
Multiplexer/Demultiplexer
TC4053B
Triple 2-Channel Multiplexer/Demultiplexer
TC4051B, TC4052B and TC4053B are multiplexers with
capabilities of selection and mixture of analog signal and digital
signal. TC4051B has 8 channels configuration. TC4052B has 4
channel × 2 configuration and TC4053B has 2 channel × 3
configuration. The digital signal to the control terminal turns
“ON” the corresponding switch of each channel, with large
amplitude (VDD − VEE) can be switched by the control signal
with small logical amplitude (VDD − VSS). For example, in the
case of VDD = 5 V VSS = 0 V and VEE = −5 V, signals between −5
V and +5 V can be switched from the logical circuit with single
power supply of 5 volts. As the ON-resistance of each switch is
low, these can be connected to the circuits with low input
impedance.
TC4051BP, TC4052BP, TC4053BP
TC4051BF, TC4052BF, TC4053BF
TC4051BFT, TC4052BFT, TC4053BFT
Weight
DIP16
-P-300-2.54A : 1.00 g (typ.)
SOP16
-P-300-1.27A : 0.18 g (typ.)
TSSOP16-P-0044-0.65A : 0.06 g (typ.)
Start of commercial production
1978-04
TC4051,4052,4053BP/BF/BFT
2016-01-15
2
Pin Assignment (top view)
Truth Table
Control Inputs “ON” Channel
Inhibit C∆ B A TC4051B TC4052B TC4053B
L L L L 0 0X, 0Y 0X, 0Y, 0Z
L L L H 1 1 X, 1Y 1X, 0Y, 0Z
L L H L 2 2X, 2Y 0X, 1Y, 0Z
L L H H 3 3 X, 3Y 1X, 1Y, 0Z
L H L L 4 ― 0X, 0Y, 1Z
L H L H 5 ― 1X, 0Y, 1Z
L H H L 6 ― 0X, 1Y, 1Z
L H H H 7 ― 1X, 1Y, 1Z
H X X X None None None
X: Don’t care
Δ: Except TC4052B
VDD
16
2
1
0
15
14
13
12
11
10
1
2
3
4
5
6
7
3
8
9
A
B
TC4051B
4
C
VDD
16
2X
1X
X-COM
15
14
13
12
11
10
1
2
3
4
5
6
7
3Y
1Y
INH
VEE
VSS
0X
8
9
3X
A
2Y
Y-COM
0Y
TC4052B
B
VDD
16
Y-COM
X-COM
1X
15
14
13
12
11
10
1
2
3
4
5
6
7
Z-COM
0Z
INH
VEE
VSS
0X
8
9
A
B
0Y
1Z
TC4053B
1Y
C
TC4051,4052,4053BP/BF/BFT
2016-01-15
3
Logic Diagram
TC4051B
TC4052B
A
B
INH
C
Logic Level Converter
OUT
IN
c
COMMON
OUT
IN
c
OUT
IN
c
OUT
IN
c
OUT
IN
c
OUT
IN
c
OUT
IN
c
OUT
IN
c
0
3
5
1
2
4
6
7
11
10
9
6
7
VEE
8
VDD
12
11
A
5
B
INH
14
15
1
2
4
Logic Level Converter
OUT
IN
c
Y-COMMON
OUT
IN
c
OUT
IN
c
OUT
IN
c
OUT
IN
c
OUT
IN
c
OUT
IN
c
OUT
IN
c
0X
3X
1Y
1X
2X
0Y
2Y
3Y
3
10
9
6
7
VEE
8
VSS
16
VDD
X-COMMON
13
TC4051,4052,4053BP/BF/BFT
2016-01-15
4
TC4053B
Truth Table
Control
C
Impedance between
IN-OUT (Note)
H
L
0.5 to 5 × 102 Ω
>109 Ω
Note: See electrical characteristics
Absolute Maximum Ratings (Note)
Characteristics Symbol Rating Unit
DC supply voltage VDD-VSS −0.5 to 20 V
DC supply voltage VDD-VEE −0.5 to 20 V
Control input voltage VCIN VSS − 0.5 to VDD + 0.5 V
Swi tch I/O voltage VI/VO VEE − 0.5 to VDD + 0.5 V
Control input current ICIN ±10 mA
Potenti al difference across I/O during ON
VI-VO −0.5 to 0.5 V
Power dissipation PD 300 (DIP)/180 (SOP/TSSOP) mW
Operating temperature range Topr −40 to 85 °C
Storage temperature range Tstg −65 to 150 °C
Note: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or
even destruction.
Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly
even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute
maximum ratings and the operating ranges.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test
report and estima ted failure rate, etc).
OUT
IN
c
14
2
A
5
B
INH
C
12
13
1
3
Logic Level Converter
Z-COMMON
OUT
IN
c
OUT
IN
c
OUT
IN
c
OUT
IN
c
OUT
IN
c
OUT
IN
c
X-COMMON
0Y
0Z
0X
1X
1Y
1Z
4
11
10
9
6
7
VEE
8
VSS
16
VDD
Y-COMMON
15
TC4051,4052,4053BP/BF/BFT
2016-01-15
5
Operating Ranges (Note)
Characteristics Symbol Test Conditi on Min Typ. Max Unit
DC supply voltage VDD-VSS ― 3 ― 18 V
VDD-VEE ― 3 ― 18
Control input voltage VIN ― VSS ― VDD V
Input/output voltage VIN/VOUT ― VEE ― VDD V
Note: The operating ranges must be main tai ned to ensure the normal operation of the device.
Unused Control inputs must be tied to either VDD or VSS.
Static Electrical Characteristics
Characteristics Symbol Test Condition −40°C 25°C 85°C Unit
V
SS
(V)
V
EE
(V)
V
DD
(V)
Min Max Min Typ. Max Min Max
Control input high
voltage VIH
VIS = VDD
thru 1 kΩ
VEE = VSS
RL = 1 kΩ
to VSS
IIS < 2 μA
on all OFF
channels
5
10
15
3.5
7.0
11.0
―
―
―
3.5
7.0
11.0
2.75
5.50
8.25
―
―
―
3.5
7.0
11.0
―
―
―
V
Control input low
voltage VIL
5
10
15
―
―
―
1.5
3.0
4.0
―
―
―
2.25
4.5
6.75
1.5
3.0
4.0
―
―
―
1.5
3.0
4.0
V
On-state
resistance RON 0 ≤ VIS ≤ VDD
RL = 10 kΩ
0
0
0
0
0
0
5
10
15
―
―
―
850
210
140
―
―
―
240
110
80
950
250
160
―
―
―
1200
300
200
Ω
ΔOn-state
resistance
between any 2
switches RON∆ ―
0
0
0
0
0
0
5
10
15
―
―
―
―
―
―
―
―
―
10
6
4
―
―
―
―
―
―
―
―
―
Ω
Input/output
leakage current IOFF VIN = 18 V, VOUT = 0 V
VIN = 0 V, VOUT = 18 V
18
18
―
―
±100
±100
―
―
±0.01
±0.01
±100
±100
―
―
±1000
±1000
nA
Quiescent supply
current IDD VIN = VSS, VDD (Note)
5
10
15
―
―
―
5.0
10
20
―
―
―
0.005
0.010
0.015
5.0
10
20
―
―
―
150
300
600
μA
Input current IIN VIH = 18 V
VIL = 0 V
18
18
―
―
0.1
−0.1
―
―
10−5
−10−5
0.1
−0.1
―
―
1.0
−1.0 μA
Input capacitance CIN ― ― ― ― ― 5 7.5 ― ― pF
Switch input
capacitance CIN ― ― ― ― ― 10 ― ― ― pF
Output
capacitance COUT
TC4051B
TC4052B
TC4053B
10
10
10
―
―
―
―
―
―
―
―
―
58
30
17
―
―
―
―
―
―
―
―
―
pF
Feedthrough
capacitance CIN-
C-OUT
TC4051B
TC4052B
TC4053B
10
10
10
―
―
―
―
―
―
―
―
―
0.2
0.2
0.2
―
―
―
―
―
―
―
―
―
pF
Note: All valid input combinations.
TC4051,4052,4053BP/BF/BFT
2016-01-15
6
Switching Characteristics (Ta = 25°C, CL = 50 pF)
Characteristics Symbol Test Conditi on Min Typ. Max Unit
V
SS
(V)
V
EE
(V)
V
DD
(V)
Phase difference between
input to output φI-O ―
0
0
0
0
0
0
5
10
15
―
―
―
15
8
6
45
20
15
ns
Propagation delay time
(A, B, C, -OUT)
tpZL
tpZH
tpLZ
tpHZ
RL = 1 kΩ
0
0
0
0
0
0
0
0
−5
−7.5
5
10
15
5
7.5
―
―
―
―
―
170
90
70
100
80
550
240
160
240
160
ns
Propagation delay time
(INH-OUT)
tpZL
tpZH RL = 1 kΩ
0
0
0
0
0
0
0
0
−5
−7.5
5
10
15
5
7.5
―
―
―
―
―
120
60
50
80
60
380
200
160
200
160
ns
Propagation delay time
(INH-OUT)
tpLZ
tpHZ RL = 1 kΩ
0
0
0
0
0
0
0
0
−5
−7.5
5
10
15
5
7.5
―
―
―
―
―
170
90
70
100
80
450
210
160
210
160
ns
−3dB cutoff frequency
TC4051B
TC4052B
TC4053B
fmax (I-O) RL = 1 kΩ (Note 1)
−5
−5
−5
−5
−5
−5
5
5
5
―
―
―
20
30
40
―
―
―
MHz
Total harmonic distortion ― RL = 10 kΩ
f = 1 kHz (Note 2)
−2.5
−5
−7.5
−2.5
−5
−7.5
2.5
5
7.5
―
―
―
0.15
0.03
0.02
―
―
―
%
−50dB feedthrough
(switch off) ― RL = 1 kΩ (Note 3)
−5 −5 5 ― 500 ― kHz
Crosstalk ― RL = 1 kΩ (Note 4)
−5 −5 5 ― 1.5 ― MHz
Crosstalk
(control-OUT) ―
RIN = 1 kΩ
ROUT = 10 kΩ
CL = 15 pF
0
0
0
0
0
0
5
10
15
―
―
―
200
400
600
―
―
―
mV
Note 1: Sine wave of ±2.5 Vp-p shall be used for Vis and the frequency of 20 log 10
is
OS
V
V
= −3dB shall be fmax.
Note 2: Vis shall be sine wave of
−
±4VV
EEDD
p-p.
Note 3: Sine wave of ±2.5 Vp-p shall be used for Vis and the frequency of 20 log 10
is
OS
V
V
= −50dB shall be
feed-through.
Note 4: Sine wave of ±2.5 Vp-p shall be used for Vis and the frequency of 20 log 10
is
OS
V
V
= −50dB shall be
crosstalk.
TC4051,4052,4053BP/BF/BFT
2016-01-15
7
Package Dimensions
Weight: 1.00 g (typ.)
TC4051,4052,4053BP/BF/BFT
2016-01-15
8
Package Dimensions
Weight: 0.18 g (typ.)
TC4051,4052,4053BP/BF/BFT
2016-01-15
9
Package Dimensions
Weight: 0.06 g (typ.)
TC4051,4052,4053BP/BF/BFT
2016-01-15
10
RESTRICTIONS ON PRODUCT USE
• Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information
in this document, and related hardware, software and systems (collect i vel y "Product" ) without not ice.
• This document and any information herein may not be reproduced without pri or written permission from TOSHIBA. Even with
TOSHIBA's written permission, reproduct i on is permiss i bl e only if reproduction is without alteration/omission.
• Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfuncti on or fail. Cust omers are
responsibl e for compl ying with safety standards and for providing adequate designs and safeguards for their hardware, software and
systems which minimi ze risk and avoid situations in which a malfunction or fail ure of Product could cause loss of human life, bodily
injury or damage to property, including data loss or corruption. Before cust om ers use the Product, create designs including the
Product, or incorporat e the Product into thei r own applicati ons, c ustomers must also refer to and comply with (a) the latest vers io ns of
all relevant TOSHIBA i nformation, including without limitation, this document, the specific at i ons , the data sheets and application notes
for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the
instruct i ons for the applicati on with which the Product will be used with or for. Customers are solely responsible for all aspects of their
own product design or applications, includi ng but not limit ed to (a) determini ng the appropriateness of the use of this Product in such
design or applications; (b) evaluat ing and determ i ni ng the applic ability of any i nformation contained in this document, or in charts,
diagrams, programs, al gorithms , sample application circuits, or any other referenced documents; and (c) validating all operating
parameters for such designs and applications. TOSHIBA AS SUM ES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR
APPLICATIONS.
• PRODUCT IS NEI THE R INTENDE D NO R WARRANTED FOR USE I N EQUIPM ENTS OR SYSTEMS THAT REQUIRE
EXTRAORDINARILY HIGH LEVELS OF QU ALITY AND/OR RELIABILITY, AND/OR A MALFUNCTIO N O R FAILURE OF WHICH
MAY CAUSE LOSS OF HUMAN LIFE, BO DILY INJURY, SERIOUS PROPERTY DAM AGE AND/OR SERIOUS PUBLIC IMPACT
("UNINTENDED USE"). E xcept for s peci fic applic at i ons as expressl y stated in this document, Unintended Use i ncludes, without
limitation, equipment used in nuclear fac iliti es, equi pm ent used in the aerospace industry, medical equipment, equipment used for
automobiles, trai ns, ships and other transportation, traffic signaling equipment, equipment us ed to control combustions or explosions,
safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. IF YOU USE
PRODUCT FOR UNINTE NDE D USE, TOSHI BA ASSUMES NO LI ABILITY FOR PRODUCT. For details, please contact your
TOSHIBA sales representative.
• Do not disassemble, anal yze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.
• Product shall not be used for or incorporated int o any products or systems whose manufacture, use, or sale is prohibited under any
applicable laws or regulati ons.
• The information contained herein is presented only as guidance for Product use. No responsi bility is assumed by TOSHIBA for any
infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to
any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.
• ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
FOR PRODUCT, AND TO THE MAXIMUM EXTE NT AL L OWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY
WH ATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQ UENTIAL, SPECIAL, OR INCI DE NTAL DAMAGES OR
LOSS, INCL UDING WITHOUT LIMITATION, L O SS OF PROFITS, LOS S OF OPP ORTUNI TI E S, BUSINESS INTERRUPTION AND
LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITI O NS RELATED TO
SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARR ANTIES OR CONDITI ONS OF MERCHANTABILITY, FITNES S
FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NO NINFRINGEME NT.
• Do not use or otherwise make available Product or related software or technology for any military purposes, including without
limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biologic al weapons or missile
technology products (mass destruct i on weapons). Product and related software and technology may be controlled under the
applicable export laws and regulat ions i ncludi ng, without l imitation, t he Japanese Foreign Exchange and Foreign Trade Law and the
U.S. Export Adm i nistrat i on Regulati ons. Export and re-export of Product or relat ed software or technology are strictly prohibi ted
except in compliance with all applicable export laws and regulat i ons.
• Please contact your TO S HIB A s ales representative for details as to environmental matters such as the RoHS compatibility of Product.
Please use Product in compliance with all applicabl e l aws and regulations t hat regulate the inclusion or use of controlled substances,
including without limi tation, the EU RoHS Directive. TOSHIBA A SSUMES NO LIABILITY FOR DAMAGES OR LOSSES
OCCURRING AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGUL AT I O NS.