D WIMA MP 3-X1 Metallized Paper (MP) RFI-Capacitors Class X1 PCM 10 mm to 27.5 mm Special Features Electrical Data Particularly high reliability against active and passive flammability Excellent self-healing as well as high voltage strength High degree of interference suppression due to good attenuation and low ESR For temperatures up to +110 C According to RoHS 2011/65/EC Typical Applications Class X1 RFI applications to meet EMC regulations Capacitors connected to the mains between phase and neutral or phase and phase conductors Installation category III in accordance with IEC 60664, pulse peak voltage T 4 kV Capacitance range: 1000 pF to 0.22 mF (E12-values on request) Rated voltages: 300 VAC, 440 VAC, 500 VAC Continuous DC voltage* (general guide): 730 V for 300 VAC 850 V for 440 VAC and 500 VAC Capacitance tolerances: 20% Operating temperature range: -40) C to +110) C Climatic test category: 40/110/56/C in accordance with IEC Insulation resistance at +20+ C: 12 x 103 M Measuring voltage: 100 V/1 min. for 300 VAC and 440 VAC 500 V/1 min. for 500 VAC Dissipation factors: tan d T 13 x 10 -3 at 1 kHz and +20+ C Approvals: Country Construction Dielectric: Paper, epoxy resin impregnated Capacitor electrodes: Vacuum-deposited Internal construction: Authority Specification Test specifications: In accordance with IEC 60384-14 Maximum pulse rise time: Capacitance pF/mF 1000 2200 6800 0.047 ... ... ... ... UL Canada CSA 1500 1100 4700 500 0.033 200 0.22 100 for pulses equal to a voltage amplitude with 2 x 300 VAC = 425 V, with 2 x 440 VAC = 623 V, with 2 x 500 VAC = 707 V according to IEC 60384-14 Test voltage: 3000 VDC, 2 sec. Reliability: Operational life 300 000 hours Failure rate 1 fit (0.5 x U r and 40) C) Symbol V Germany VDE IEC 60384-14/3 D E EN 132 400 USA Pulse rise time V/msec max. operation UL 1283 C 22.2 No. 8 Approval-No. 101355 (440/500 VAC) 89748 (300 VAC) E 100438 (300 VAC) LR 93312-1 (300 VAC) Capacitor paper Vacuum-deposited electrode Metal contact layer (schoopage) Terminating wire Encapsulation: Self-extinguishing epoxy resin, UL 94 V-0, metal foil Terminations: Tinned wire. Marking: Marking: Black on Silver. Mounting Recommendation To minimize or avoid shock and/or vibration stresses to terminating wires and solder connections we recommend to fix voluminous resin-potted MP capacitors as from e.g. PCM 22.5 mm in an appropriate way since for constructional reasons they do not sit tight on the board. Packing Available taped and reeled up to and including PCM 22.5 mm. Detailed taping information and graphs at the end of the catalogue. For further details and graphs please refer to Technical Information. * If safety-approved EMI suppression capacitors are operated with a DC voltage being above the specified AC voltage rating the given approvals are no longer valid (IEC 60384-14). Furthermore the permissible pulse rise time du/dt (F max.) will be subject to a reduction according to 11.12 Fmax. = F r x 2 x UAC / UDC if the DC operating voltage UDC is higher than 2 x UAC 79 D WIMA MP 3-X1 Continuation General Data Capacitance 1000 1500 2200 3300 4700 6800 0.01 0.015 0.022 0.033 0.047 0.068 0.1 0.15 0.22 pF mF mF Capacitance 6800 0.01 0.015 0.022 0.033 pF mF W 4 4 4 4 5 5 5 6 7 8 10 8 10 12 13 H 8.5 8.5 8.5 8.5 10 13 13 14 15 17 18 20 22 24 25 W 5 5 6 7 10 H 13 13 14 15 18 300 VAC * L PCM** Part number 13.5 10 MPX12W1100FA00_ _ _ _ 13.5 10 MPX12W1150FA00_ _ _ _ 13.5 10 MPX12W1220FA00_ _ _ _ 13.5 10 MPX12W1330FA00_ _ _ _ 13.5 10 MPX12W1470FB00_ _ _ _ 19 15 MPX12W1680FC00_ _ _ _ 19 15 MPX12W2100FC00_ _ _ _ 19 15 MPX12W2150FD00_ _ _ _ 19 15 MPX12W2220FE00_ _ _ _ 19 15 MPX12W2330FF00_ _ _ _ 19 15 MPX12W2470FG00_ _ _ _ 28 22.5 MPX12W2680FH00_ _ _ _ 28 22.5 MPX12W3100FI00_ _ _ _ 28 22.5 MPX12W3150FJ00_ _ _ _ 33 27.5 MPX12W3220FK00_ _ _ _ L 19 19 19 19 19 * f = 50/60 Hz Dims in mm. Rights reserved to amend design data without prior notification. Typical Graphs of the Capacitor Paper Dielectric 500 VAC * PCM** Part number 15 MPX15W1680FC00_ _ _ _ 15 MPX15W2100FC00_ _ _ _ 15 MPX15W2150FD00_ _ _ _ 15 MPX15W2220FE00_ _ _ _ 15 MPX15W2330FG00_ _ _ _ H L 5 5 6 7 10 13 13 14 15 18 19 19 19 19 19 MP 3-X2 MP 3-X1 MP 3-Y2 8 4 MP 3R-Y2 -4 -8 -20 0 20 40 PCM at the pin exi t points ( 0.5) 60 80 100 T( C) tan (x 10-3) 40 36 32 28 24 20 16 12 8 4 0 -55 -40 -20 Capacitance change versus temperature (f =1 kHz) (general guide) 104 d d = 0.6 l if PCM10 d = 0.8 l if PCMU15 C/C (%) -12 -55 -40 L H 0 valid for: MPX14W1680FC00_ _ _ _ MPX14W2100FC00_ _ _ _ MPX14W2150FD00_ _ _ _ MPX14W2220FE00_ _ _ _ MPX14W2330FG00_ _ _ _ W 6 -2 20 % = M bulk = S 6-2 = SD Taped version see page 148. 12 15 15 15 15 15 Part number ** PCM = Printed circuit module = pin spacing Upon request with long pins 35-2 mm max. Part number completion: Tolerance: Packing: Pin length: 440 VAC* PCM** W M x F(s) 0 20 40 60 80 100 T( C) Dissipation factor change versus temperature (f = 1 kHz) (general guide) 30 tan (x 10-3) 26 22 18 103 14 10 6 -20 0 20 40 60 80 100 T( C) Insulation resistance change versus temperature (general guide) 80 2 0 2 10 103 104 105 Dissipation factor change versus frequency (general guide). f/Hz 106 11.12 102 -55 -40 D Recommendation for Processing and Application of Through-Hole Capacitors Soldering Process Wave soldering T A preheating of through-hole WIMA capacitors is allowed for temperatures T max P 100 C. In practice a preheating duration of t P 5 min. has been proven to be best. 260 240 220 200 180 160 140 120 100 80 60 40 20 Single wave soldering Soldering bath temperature: T P 260 C Immersion time: t P 5 sec Double wave soldering Soldering bath temperature: T P 260 C Immersion time: 2 x t P 3 sec Due to different soldering processes and heat requirements the graphs are to be regarded as a recommendation only. 10 s [C] see detailenlargement 2s 3s t 30 60 90 120 150 180 210 240 [sec] Typical temperature/time graph for double wave soldering WIMA Quality and Environmental Philosophy ISO 9001:2008 Certification ISO 9001:2008 is an international basic standard of quality assurance systems for all branches of industry. The approval according to ISO 9001:2008 of our factories by the VDE inspectorate certifies that organisation, equipment and monitoring of quality assurance in our factories correspond to internationally recognized standards. WIMA WPCS The WIMA Process Control System (WPCS) is a quality surveillance and optimization system developed by WIMA. WPCS is a major part of the quality-oriented WIMA production. Points of application of WPCS during production process: incoming material inspection metallization film inspection schoopage pre-healing pin attachment cast resin preparation/ encapsulation " 100% final inspection " AQL check All WIMA capacitors, irrespective of whether through-hole devices or SMD, are made of environmentally friendly materials. Neither during manufacture nor in the product itself any toxic substances are used, e.g. - - - - - Lead PCB CFC Hydrocarbon chloride Chromium 6+ - - - - - PBB/PBDE Arsenic Cadmium Mercury etc. We merely use pure, recyclable materials for packing our components, such as: " " " " carton cardboard adhesive tape made of paper polystyrene We almost completely refrain from using packing materials such as: " foamed polystyrene (Styropor(R)) " adhesive tapes made of plastic " metal clips RoHS Compliance According to the RoHS Directive 2011/65/EC certain hazardous substances like e.g. lead, cadmium, mercury must not be used any longer in electronic equipment as of July 1st, 2006. For the sake of the environment WIMA has refraind from using such substances since years already. WIMA Kondensatoren sind bleifrei konform RoHS 2011/65/EC WIMA capacitors are lead free in accordance with RoHS 2011/65/EC Tape for lead-free WIMA capacitors DIN EN ISO 14001:2004 WIMA's environmental management has been established in accordance with the guidelines of DIN EN ISO 14001:2004 to optimize the production processes with regard to energy and resources. 11.12 " " " " " " " WIMA Environmental Policy 14 D Typical Dimensions for Taping Configuration Vh P P2 Diagram 1: PCM 2.5/5/7.5mm W W1 W0 H H1 W2 P1 D0 d P t F P0 H1 P P1 H P1 d d P0 P2 F Diagram 2: PCM 10/15 mm Diagram 3: PCM 22.5 and 27.5*mm *PCM 27.5 taping possible with two feed holes between components Designation Carrier tape width Dimensions for Radial Taping Symbol PCM 2.5 taping W P0 P2 F 18.0 p0.5 PCM 5 taping PCM 7.5 taping PCM 10 taping* PCM 15 taping* PCM 22.5 taping PCM 27.5 taping 18.0 p0.5 18.0 p0.5 18.0 p0.5 18.0 p0.5 18.0 p0.5 18.0 p0.5 for hot-sealing for hot-sealing for hot-sealing for hot-sealing for hot-sealing for hot-sealing for hot-sealing Hold-down tape width W0 6.0 6.0 12.0 12.0 12.0 12.0 12.0 adhesive tapeadhesive tapeadhesive tapeadhesive tapeadhesive tapeadhesive tapeadhesive tape Hole position W1 9.0 p0.5 9.0 p0.5 9.0 p0.5 9.0 p0.5 9.0 p0.5 9.0 p0.5 9.0 p0.5 Hold-down tape position W2 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. Feed hole diameter D0 4.0 p0.2 4.0 p0.2 4.0 p0.2 4.0 p0.2 4.0 p0.2 4.0 p0.2 12.7 p1.0 12.7 p1.0 12.7 p1.0 25.4 p1.0 25.4 p1.0 38.1 p1.5 4.0 p0.2 3*8.1 p1.5 or 50.8 p1.5 Pitch of component P Feed hole pitch P0 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch Feed hole centre to pin P1 5.1 p0.5 3.85 p0.7 2.6 p0.7 7.7 p0.7 5.2 p0.7 7.8 p0.7 5.3 p0.7 Hole centre to component centre P2 6.35 p1.3 6.35 p1.3 6.35 p1.3 12.7 p1.3 12.7 p1.3 19.05 p1.3 19.05 p1.3 Feed hole centre to bottom H edge of the component 16.5 p0.3 18.5 p0.5 16.5 p0.3 18.5 p0.5 16.5 p0.5 18.5 p0.5 16.5 p0.5 18.5 p0.5 16.5 p0.5 18.5 p0.5 16.5 p0.5 18.5 p0.5 16.5 p0.5 18.5 p0.5 Feed hole centre to top H edge of the component1 H+Hcomponent < H1 32.25 max. H+Hcomponent < H1 32.25 max. H+Hcomponent < H1 24.5 to 31.5 H+Hcomponent < H1 25.0 to 31.5 H+Hcomponent < H1 26.0 to 37.0 H+Hcomponent < H1 30.0 to 43.0 H+Hcomponent < H1 35.0 to 45.0 Pin spacing at +0.8 F 2.5 p0.5 5.0 upper edge of carrier tape -0.2 7.5 p0.8 10.0 p0.8 15 p0.8 22.5 p0.8 27.5 p0.8 Pin diameter d 0.4 p0.05 Component alignment Dh p 2.0 max. p 2.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max. 0.7 p0.2 0.7 p0.2 0.7 p0.2 0.7 p0.2 0.7 p0.2 0.7 p0.2 0.7 p0.2 Total tape thickness t Package (see also page 149) REEL 0.5 p0.05 0.5 +0.06 p0.05 or 0.6 -0.05 0.5 +0,06 p0.05 or 0.6 -0.05 ROLL/AMMO P 360 max. 52 p2 P 30 p1B 58 p2 depending on comp. dimensions Unit 0.8 +0,08 -0.05 0.8 +0,08 -0.05 +0.08 0.8 -0.05 AMMO 52 p2 54 p2 max. P 500 max. B 58 p2 or REEL B 60 p2 REEL PP 360 30 p1 P 25 p1 66 p2 68 p2 depending on PCM and component dimensions see details page 150. Dims in mm. Diameter of pins see General Data. * PCM 10 and PCM 15 can be crimped to PCM 7.5. Position of components according to PCM 7.5 (sketch 1). P 0 = 12.7 or 15.0 is possible 148 Please clarify customer-specific deviations with the manufacturer. 11.12 D Types of Tape Packaging of Capacitors for Automatic Radial Insertion REEL Packaging 340 max. 301 251 360 max. 500 max. AMMO Packaging 340 max. 370 max. ROLL Packaging 34 0m ax. 50 max. 50 max. 70 max. . ax 0 m ax. 34 0 m 49 B BAR CODE (Labelling) Labelling of package units in plain text and with alphanumerical Bar Code BARCODE Code 39" Scanner decoding of WIMA supplier number Customer`s P/O number Customer`s part number WIMA confirmation number WIMA part number Lot number Date code Quantity In addition part description of - - - - - - article capacitance value rated voltage dimensions capacitance tolerance packing 11.12 as well as gross weight and customer`s name are indicated in plain text. 149 D Packing Quantities for Capacitors with Radial Pins in PCM 2.5 mm to 22.5 mm Size PCM 2.5 mm 5 mm 7.5 mm 10 mm 15 mm 22.5 mm W 2.5 3 3.8 4.6 5.5 2.5 3 3.5 4.5 4.5 5 5.5 5.5 6.5 7.2 7.2 8.5 8.5 11 2.5 3 4 4.5 5 5.7 7.2 3 4 4 4 5 5 6 6 8 5 5 6 6 7 7 8 8 9 9 10 11 5 6 7 8 8.5 10 10.5 10.5 11 12 H 7 7.5 8.5 9 10 6.5 7.5 8.5 6 9.5 10 7 11.5 8 8.5 13 10 14 16 7 8.5 9 9.5 10.5 12.5 12.5 9 8.5 9 9.5 10 11 12 12.5 12 11 13 12.5 14 14 15 15 17 14 16 18 14 14 15 16.5 20 18.5 22 19 20.5 21 24 bulk L 4.6 4.6 4.6 4.6 4.6 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 10 10 10 10.3 10.3 10.3 10.3 13 13.5 13 13 13.5 13 13 13 13 18 19 18 19 18 19 18 19 18 18 19 18 26.5 26.5 26.5 28 26.5 28 26.5 26.5 26.5 28 Codes 0B 0C 0D 0E 0F 1A 1B 1C 1D 1E 1F 1G 1H 1I 1J 1K 1L 1M 1N 2A 2B 2C 2D 2E 2F 2G 3A FA 3C 3D FB 3F 3G 3H 3I 4B FC 4C FD 4D FE 4F FF 4H 4J FG 4M 5A 5B 5D FH 5F FI 5G 5H 5I FJ S 5000 5000 5000 5000 5000 5000 5000 5000 6000 4000 3500 4000 2500 2500 2500 2000 2000 1500 1000 5000 5000 4000 3500 3000 2000 1500 3000 3000 3000 3000 2000 3000 2400 2400 2000 2400 1000 2000 1000 1600 1000 1200 500 1200 900 500 1000 1200 1000 760 500 500 540* 680* 680* 680* 450* Moulded versions. Rights reserved to amend design data without prior notification. 11.12 * TPS (Tray-Packing-System). Plate versions may have different packing units. Samples and pre-production needs on request. pcs. per packing unit REEL AMMO P 360 P 500 340 x 340 490 x 370 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 N O F I H J A C B D 2200 2500 - 2800 - 2000 2300 - 2300 - 1500 1800 - 1800 - 1200 1500 - 1500 - 900 1200 - 1200 - 2200 2500 - 2800 - 2000 2300 - 2300 - 1600 2000 - 2000 - 1300 1500 - 1500 - 1300 1500 - 1500 - 1100 1400 - 1400 - 1000 1200 - 1200 - 1000 1200 - 1200 - 800 1000 - 1000 - 700 1000 - 1000 - 700 950 - 1000 - 600 800 - 800 - 600 800 - 800 - 500 600 - 400 - - 2500 4400 2500 - - 2200 4300 2300 4150 - 1700 3200 1700 3100 - 1500 2900 1400 2800 - 1300 2500 1300 - - 1000 2200 1100 - - 900 1800 1000 - - 1100 2200 - 1900 - 900 1600 - 1450 - 900 1600 - 1450 - 900 1600 - 1400 - 700 1300 - 1200 - 700 1300 - 1200 - 550 1100 - 1000 - 550 1100 - 1000 - 400 800 - 740 - 600 1200 - 1150 - 600 1200 - 1200 - 500 1000 - 1000 - 500 1000 - 1000 - 450 900 - 850 - 450 900 - 850 - 400 800 - 740 - 400 800 - 740 - 350 700 - 650 - 350 700 - 650 - 300 650 - 590 - 300 600 - 540 - - 800 - 770 - - 700 - 640 - - 600 - 550 - - 500 - 480 - - 480 - 450 - - 420 - 380 - - 400 - 360 - - 400 - 360 - - 380 - 350 - - 350 - 310 ROLL 150 D Packing Quantities for Capacitors with Radial Pins in PCM 27.5 mm to 52.5 mm Size PCM pcs. per packing unit REEL AMMO P 360 P 500 340 x 340 490 x 370 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 N O F I H J A C B D - - 460/340* - 420 - - 380/280* - 350 - - 300 - 290 - - - - - 270 - 250 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ROLL bulk W 9 11 13 13 15 15 17 17 19 20 20 H 19 21 24 25 26 26 29 34.5 30 32 39.5 L 31.5 31.5 31.5 33 31.5 33 31.5 31.5 31.5 33 31.5 Codes 6A 6B 6D FK 6F FL 6G 6I 6L FM 6J S 640* 544* 448* 336* 384* 288* 176* 176* 50* 216* 144* 37.5 mm 9 11 13 15 17 19 20 24 31 35 40 19 22 24 26 29 32 39.5 45.5 46 50 55 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 7A 7B 7C 7D 7E 7F 7G 7H 7I 7J 7K 480* 408* 252* 144* 132* 108* 108* 84* 72* 35* 28* - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 48.5 mm 19 23 27 33 37 31 34 37.5 48 54 56 56 56 56 56 8D 8E 8H 8J 8L 50* 72* 60* 48* 25* - - - - - - - - - - - - - - - - - - - - - - - - - 52.5 mm 35 45 45 50 55 65 57 57 57 9F 9H 9J 25* 20* 20* - - - - - - - - - - - - - - - 27.5 mm Moulded versions. Rights reserved to amend design data without prior notification. 11.12 * for 2-inch transport pitches. * TPS (Tray-Packing-System). Plate versions may have different packing units. Samples and pre-production needs on request. 151 D WIMA Part Number System A WIMA part number consists of 18 digits and is composed as follows: Field 1 - 4: Type description Field 5 - 6: Rated voltage Field 7 - 10: Capacitance Field 11 - 12: Size and PCM Field 13 - 14: Version code (e.g. Snubber versions) Field 15: Capacitance tolerance Field 16: Packing Field 17 - 18: Lead length (untaped) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 M K S 2 C 0 2 1 0 0 1 A 0 0 M S S D 20 % bulk Type description: SMD-PET = SMD-PPS = FKP 02 = MKS 02 = FKS 2 = FKP 2 = MKS 2 = MKP 2 = FKS 3 = FKP 3 = MKS 4 = MKP 4 = MKP 10 = FKP 4 = FKP 1 = MKP-X2 = MKP-X2 R = MKP-Y2 = MP 3-X2 = MP 3-X1 = MP 3-Y2 = MP 3R-Y2 = Snubber MKP = Snubber FKP = GTO MKP = DC-LINK MKP 3 = DC-LINK MKP 4 = DC-LINK MKP 4S = DC-LINK MKP 5 = DC-LINK MKP 6 = DC-LINK HC = DC-LINK HY = SuperCap C = SuperCap MC = SuperCap C60 = SuperCap R = SuperCap MR = 63 VDC SMDT SMDI FKP0 MKS0 FKS2 FKP2 MKS2 MKP2 FKS3 FKP3 MKS4 MKP4 MKP1 FKP4 FKP1 MKX2 MKXR MKY2 MPX2 MPX1 MPY2 MPRY SNMP SNFP GTOM DCP3 DCP4 DCPS DCP5 DCP6 DCH_ DCHY SCSC MC_ _ SCSC SCSR MRPP Rated voltage: 2.5 VDC = A1 4 VDC = A2 14 VDC = A3 28 VDC = A4 40 VDC = A5 5 VDC = A6 50 VDC = B0 63 VDC = C0 100 VDC = D0 160 VDC = E0 250 VDC = F0 400 VDC = G0 450 VDC = H0 600 VDC = I0 630 VDC = J0 700 VDC = K0 800 VDC = L0 850 VDC = M0 900 VDC = N0 1000 VDC = O1 1100 VDC = P0 1200 VDC = Q0 1250 VDC = R0 1500 VDC = S0 1600 VDC = T0 2000 VDC = U0 2500 VDC = V0 3000 VDC = W0 4000 VDC = X0 6000 VDC = Y0 250 VAC = 0W 275 VAC = 1W 300 VAC = 2W 400 VAC = 3W 440 VAC = 4W 500 VAC = 5W ... 0.01 mF Capacitance: 22 pF = 0022 47 pF = 0047 100 pF = 0100 150 pF = 0150 220 pF = 0220 330 pF = 0330 470 pF = 0470 680 pF = 0680 1000 pF = 1100 1500 pF = 1150 2200 pF = 1220 3300 pF = 1330 4700 pF = 1470 6800 pF = 1680 0.01 mF = 2100 0.022 mF = 2220 0.047 mF = 2470 0.1 mF = 3100 0.22 mF = 3220 0.47 mF = 3470 = 4100 1 mF 2.2 mF = 4220 4.7 mF = 4470 = 5100 10 mF = 5220 22 mF = 5470 47 mF 100 mF = 6100 220 mF = 6220 1F = A010 2.5 F = A025 50 F = A500 100 F = B100 110 F = B110 600 F = B600 1200 F = C120 ... - 2.5 x 6.5 x 7.2 Size: 4.8 x 3.3 x 3 Size 1812 4.8 x 3.3 x 4 Size 1812 5.7 x 5.1 x 3.5 Size 2220 5.7 x 5.1 x 4.5 Size 2220 7.2 x 6.1 x 3 Size 2824 7.2 x 6.1 x 5 Size 2824 10.2 x 7.6 x 5 Size 4030 12.7 x 10.2 x 6 Size 5040 15.3 x 13.7 x 7 Size 6054 2.5 x 7 x 4.6 PCM 2.5 3 x 7.5 x 4.6 PCM 2.5 2.5 x 6.5 x 7.2 PCM 5 3 x 7.5 x 7.2 PCM 5 2.5 x 7 x 10 PCM 7.5 3 x 8.5 x 10 PCM 7.5 3 x 9 x 13 PCM 10 4 x 9 x 13 PCM 10 5 x 11 x 18 PCM 15 6 x 12.5 x 18 PCM 15 5 x 14 x 26.5 PCM 22.5 6 x 15 x 26.5 PCM 22.5 9 x 19 x 31.5 PCM 27.5 11 x21 x 31.5 PCM 27.5 9 x 19 x 41.5 PCM 37.5 11 x 22 x 41.5 PCM 37.5 94 x 49 x 182 DCH_ 94 x 77 x 182 DCH_ ... Version code: Standard = Version A1 = Version A1.1.1 = Version A2 = ... 00 1A 1B 2A = = = = = = = = = = = = = = = = = = = = = = = = = = = KA KB QA QB TA TB VA XA YA 0B 0C 1A 1B 2A 2B 3A 3C 4B 4C 5A 5B 6A 6B 7A 7B H0 H1 Tolerance: 20 % = 10 % = 5% = 2.5 % = 1% = ... 6 -2 M K J H E Packing: AMMO H16.5 340 x 340 AMMO H16.5 490 x 370 AMMO H18.5 340 x 340 AMMO H18.5 490 x 370 REEL H16.5 360 REEL H16.5 500 REEL H18.5 360 REEL H18.5 500 ROLL H16.5 ROLL H18.5 BLISTER W12 180 BLISTER W12 330 BLISTER W16 330 BLISTER W24 330 Bulk/TPS Standard ... A B C D F H I J N O P Q R T S Lead length (untaped) 3.5 0.5 = C9 6 -2 = SD 16 1 = P1 ... The data on this page is not complete and serves only to explain the part number system. Part number information is listed on the pages of the respective WIMA range. 146 = = = = = = = = = = = = = = = 11.12 MKS 2