SL-A11 - Sunx - Product.Network

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

Sensor & Wire-saving Link System

‘T’-branch Multi-drop

System Enabling

Flexible Cable Layout

Marked

Conforming to EMC Directive

(Except some components)

Till now

‘T’-branch S-LINK saves wires throughout the layout!

(Tree architecture)

Moreover, wiring and maintenance is significantly simplified.

Cylinder

Photoelectric sensor

Fiber sensor

Lamp

Solenoid

Limit switch

Manifold electromagnetic valve

Inductive proximity sensor

From now on

Many wires, high cost, and yet miswiring.

(Point-to-point wiring)

‘T’-branch

S-LINK

‘T’-branch Multi-drop

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

Wire-saving

Three concepts of S-LINK

Quick

construc

tion

Space-effective

䢇 The use of wires is greatly

reduced and the number of

connecting terminal blocks

is minimized, resulting in

large reduction in cost, as

well as, the waste generat-

ed during wiring.

䢇

The layout of devices be-

comes flexible and the

design is easier due to the

‘T’-branch multi-drop wiring.

䢇 Since the wiring is simple,

miswiring is also sharply

decreased.

䢇

The time required for equip-

ment wiring is greatly reduced,

contributing to reduction in

electrical works cost.

Further, design and mainte-

nance personnel expenses

are also sharply decreased.

䢇 Sensors can be easily con-

nected with plug-in connec-

tion.

• Connection by plug-in unit

• Connection by connector

䢇 The addition of an I/O out-

put device is easy. Con-

struction can be done in

a short time.

䢇 The control box can be of

smaller size since connect-

ing terminal blocks are not

needed.

䢇 S-LINK devices are com-

pact. Hence, the control

box can be mounted in a

tight space.

䢇 It contributes to the minia-

turization of the machine

due to reduced wiring

space.

SL-FP3

Machinery

cost

Electrical

works

cost

Large cost

saving

Machinery

ⴐ

Electrical

works

cost

Construction

cost

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

Address

display

‘T’-branch

multi-drop

Two signal lines

Two power lines

Max. 200m

Max. 128 I/Os

No problem if the cable

breaks at any one place.

In case the cable breaks

here, the controller indi-

cates Address No.1.

Address

No.0 Address

No.1

The S-LINK system can be independently

operated without the PLC.

Checking inputs/

outputs is easy.

S-LINK Transmits 128 I/Os on Two Signal Lines and Realizes ‘T’-branch Multi-drop Wiring (Tree Architecture)

S-LINK enables transmission of 128 I/Os of sensors, switches, or actuators on two signal lines up to 200m (400m with the

booster). The S-LINK lines can be branched off in any direction, at any point, so that a flexible cable layout is possible. The

original SUNX signal processing enables highly reliable ‘T’-branch multi-drop wiring.

Caution: The connectable I/O number might decrease from 128 points depending upon the type of devices and their place of connection.

• Since the S-LINK system can operate even when the

PLC is disconnected, the system construction time can be

drastically reduced by parallel development of the soft-

ware (PLC program) and the hardware (equipment

assembly, I/O device check). Further, in case of an error,

it can be immediately found whether the error is on the

PLC side or the I/O device side.

•A handy monitor which can check I/O devices is available.

The handy monitor can be hooked up to the S-LINK sig-

nal transmission lines at any place. I/O states can be

checked in batches of 16. The handy monitor is also

incorporated with the S-LINK controller functions, so that,

for example, it can perform an I/O check on conveyor sys-

tem segments, still under assembly, even without the

S-LINK controller.

Easy Input/Output Check

•The S-LINK system automatically

turns its power off when excess

current flows through the signal

lines due to a short-circuit.

•The double code collation makes

the signal transmission secure

and reliable.

•S-LINK’s unique signal transmis-

sion, large voltage amplitude (0 -

24V) and wide pulse width (35!s)

provide high noise immunity. The

signal transmission time is 5ms

approx. for 32 points, or 11ms

approx. for 128 points.

Highly Reliable Signal Transmission

•The loop wiring maintains the sig-

nal transmission over the entire

system even if the loop may break

at any one place.

•

If the cable breaks somewhere, the

controller finds out the addresses

of all disconnected units, and dis-

plays their first address. Specify-

ing error addresses shortens the

repairing time.

S-LINK controller

SL-CU1A

Handy monitor

SL-HM1

Note: Although, SL-HM1 incorporates the functions of the SL-CU1A con-

troller, PLC I/O connectors cannot be connected.

SL-CU1A

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

Suitable for Various PLCs

• Connectable to terminal block type PLC

•Multi-core cable PLC I/O units SL-S, SL-SP, SL-P, SL-PP

are connectable to terminal block type PLCs.

• Easily connectable to different manufacturers’ PLCs

•PLC I/O connectors SL-S䡺, SL-P䡺are one-touch con-

nectable to different manufacturers’ PLC I/O modules.

Connectable PLC manufacturers

• Matsushita Electric Works • Mitsubishi Electric Corp. • Omron Corp.

• Yokogawa Electric Corp. • Sharp Corp. • Fuji Electric Works • Hitachi

• Yasukawa Electric Corp. • Toshiba Corp. • Toshiba Machine Co.

Suitable for Personal Computers

Suitable for PLC Bus

SL-CU1A

To S-LINK

system

I/O modules of different

manufacturers’ PLCs

PLC I/O connectors

I/O data

Multi-core cable PLC I/O unit

Multi-core cableSL-CU1A

I/O modules of different

manufacturers’ terminal

block type PLCs

To S-LINK system

• Direct connection to PLC bus

•S-LINK controller for direct connection to Matsushita

Electric Works’ PLC FP3/FP10SH/FP10S bus line or

Yokogawa Electric’s PLC FA-M3 series bus line, and

S-LINK control boards for direct connection to the bus line

of Matsushita Electric Works’ board type PLC, FP-C or

Sharp’s board type PLC, J-board Z-300 series, are avail-

able. Since they incorporate the S-LINK control functions

and the PLC I/O connector functions, large cost and space

savings are achieved.

For VME bus

SL-VMES2

For Sharp J-board Z-300 series

SL-Z300

For Matsushita Electric

Works PLC FP-C

SL-FPC

For Yokogawa

Electric PLC

FA-M3 series

SL-FAM3

For PC/AT

SL-PCAT For PC/FC-98 series

SL-PC98

For Matsushita

Electric Works PLC

FP3/FP10SH/FP10S

SL-FP3

• Direct connection to personal computers

•As control by personal computers has spread in recent

years, S-LINK control boards for direct connection to PCI

bus, PC/AT and compatibles (ISA bus) and to NEC

PC/FC-98 series (C bus) have been developed, in order to

enable control of the S-LINK system by a personal com-

puter. Further, S-LINK control board for direct connection

to the VME bus line is also available. Flexibility in design

has been increasingly improved.

‘T’-branch

128 I/Os can be controlled by

just two signal lines

Loop wiring is also possible

POWERCPU

IN64

OUT64

SL-SP3

S-LINK

controller

SL-FP3,

alone, is

sufficient

Module

for output

Module

for intput

PLC I/O connector

Two slots are

occupied

One slot is

occupied

This space is also

not necessary !

Construction using SL-FP3

Normal construction

In case Matsushita Electric Works PLC bus S-LINK

controller SL-FP3 is used.

POWERCPU

IN64

OUT64

IN64

OUT64

mPlease refer to P.44 for the connectable PLCs of each manufacturer.

For PCI

SL-PCI

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

SEND

SET

ADDRESS

OFF

CHK.

0 ~ 31

32~ 63

64~ 95

96~ 127

OFF

OUT

RUN

STAT.

SYS.

ADD.

ER1

ER3

SHI.

ER4

OFF

S-LINK GATEWAY CONTROLLER

SL-GU1-D

N8Q05JAPAN

SEND

SET

ADDRESS

OFF

CHK.

0 ~ 31

32~ 63

64~ 95

96~ 127

OFF

OUT

RUN

STAT.

SYS.

ADD.

ER1

ER3

SHI.

ER4

OFF

S-LINK GATEWAY CONTROLLER

SL-GU1-D

N8Q05JAPAN

Master unit made by different

PLC manufacturers

Suitable devices for different manufacturers’ fieldbus networks

Graphic panel Temperature controller etc.

S-LINK

gateway controller

Max. 128 I/O channels connectable per

S-LINK gateway controller

Sensor & wire-saving link system S-LINK

ON/OFF devices are

connected by quick

construction, wire-

saving S-LINK system

Easy connection and neat

wiring by ‘T’-branches

using hook-up connectors

High performance devices

are connected by wire-saving

fieldbus network

Compatible with Global Fieldbus Networks

Globally, fieldbus networks for FA are spreading rapidly to realize wire-saving connections between PLCs of different manu-

factures, or high performance devices, such as, temperature controllers, graphic panels etc. SUNX has developed gateway

controllers which enable connection of S-LINK to the fieldbus networks being used in different parts of the world. Hence,

wire-saving connections and other advantages of S-LINK can be realized even when using fieldbus networks.

For Device Net

SL-GU1-D For PROFIBUS-DP

SL-GU1-P For INTERBUS

SL-GU1-I For CC-link

SL-GU1-C For JPCN-1/RS-485

SL-CU1-485

JPCN-1/RS-485

Master board for

PC/FC-98 series

SL-PC98-485

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

• Seamless connection to fieldbus networks

•S-LINK can be connected seamlessly to fieldbus networks

using the S-LINK gateway controllers.

• Advanced wire-saving connection with S-LINK and

fieldbus networks

•Wire-saving connections can be realized even when using

fieldbus networks. An efficient wire-saving network can be

implemented by connecting distributed bit level data I/O

devices, such as, sensors, switches, etc., by S-LINK.

• Personal computer can be used as master (for JPCN-1/RS-485)

•PC/AT or compatible (ISA bus), NEC PC/FC-98 series personal computer or PC/104 bus board can be used as a master

unit. Long distance and multi-point control is easily possible with a personal computer when the JPCN-1/RS-485 master

board and the S-LINK gateway controller for JPCN-1/RS-485, SL-CU1-485, are used.

•The master boards for personal computers can be used in the following two modes:

•1 S-LINK mode (using RS-485 communication)

•2 JPCN-1 mode

(Please arrange a driver software separately, when using the JPCN-1 mode.)

Advantage of using with higher level networks

• Long distance transmission

The max. transmission distance is as follows.

DeviceNet: 500m, PROFIBUS-DP and CC-Link: 1,200m,

INTERBUS: 13km, JPCN-1/RS-485: 1,000m.

S-LINK can transmit up to 400m using the booster

(SL-BS1A). Hence, a system of total 1,600m can be con-

structed with PROFIBUS-DP or CC-Link (DeviceNet:

900m, INTERBUS: 13.4km).

• Total I/O channels 8,064 Nos.

Up to 99 Nos. of S-LINK gateway controllers can be con-

nected as slaves to one PROFIBUS-DP master unit

[DeviceNet: 63 Nos., INTERBUS: 256 Nos., JPCN-1/

RS-485: 31 Nos., CC-Link: 32 Nos. (Note 2)]. Since max.

128 Nos. I/O devices can be connected to one S-LINK

gateway controller, I/O signal of total 12,672 channels

[DeviceNet: 8,064 channels, INTERBUS: 4,096 channels

(Note 3), JPCN-1/RS-485: 3,968 channels, CC-Link:

2,048 channels (Note 2)] can be transmitted.

Since the higher level networks mostly use cascade wiring with

shielded twisted pair cable, the flexibility in wiring and wiring

operations have not improved. In S-LINK, ‘T’-branch flexible lay-

out can be realized using different types of quick connecting

hook-up connectors, and distributed ON/OFF data devices, such

as, switches, sensors, etc., can be efficiently wired. In this man-

ner, an exceedingly efficient wire-saving link system can be real-

ized in combination with higher level networks.

Notes: 1) The total No. of I/O channels may be less than the maximum No.

mentioned above depending on the master unit capacity. Also, the

No. of devices connectable to the S-LINK system may be less than

128 Nos., depending on the type of devices and places connected.

Notes: 2)

In case of the S-LINK gateway controller for CC-Link, the No. of

controllable I/O channels varies with the No. of units connected to

CC-Link.

Notes: 3) For INTERBUS, one master unit can control up to 4,096 I/O chan-

nels only.

Master board for personal computer

SL-PCAT-485

SL-PC98-485

SL-PC104-485

S-LINK gateway controller

SL-CU1-485

To S-LINK

system

Communication can be easily done in S-LINK mode.

(Communication can also be done in JPCN-1 mode.)

Direct hook-up!!

Master board for

PC/104 bus

SL-PC104-485

Master board for

PC/AT

SL-PCAT-485

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

1 Channel I/O Unit SL-CH1, SL-CH1-PN

I/O Unit Selectable According to the Application

2 Channel I/O Unit SL-CH21, SL-CH21-PN, SL-CH21K

•

Different devices can be simply connected at any place

•

SL-CH1(-PN) can be used as either an input unit or an output

unit by switch selection. Hence, a sensor, limit switch, etc., is

connectable when it is used as an input unit, and a relay,

lamp, etc., is connectable when it is used as an output unit. It

can be connected by a ‘T’-branch at any place on the S-LINK

cable.

Sensor or relay

It handles either the input signal from a

sensor or the output signal to a relay.

Sensor

Relay

•Both input and output devices are connectable

•

SL-CH21(-PN) allows connection of one input and one out-

put device. It is useful for a mechanism using both input

and output devices.

•SL-CH21K, isolation type for power supply remote control

function of NEC FA personal computer FC-98/FC98-NX

series, is also now available.

ApplicationApplication

Cylinder with electromagnetic valve

It handles both the input signal from a

cylinder switch and the output signal to

an electromagnetic valve.

Electromagnetic

valve

Cylinder switch

2 Channel Input Unit SL-CH20, SL-CH20-PN

•Two input devices are connectable

•

SL-CH20(-PN) allows connection of two input devices, and

handles both signals. It contributes to cost-effectiveness if

you use several input devices.

Application

Sensor and limit switch

It handles two input signals from a sen-

sor and a limit switch, two sensors, or

two limit switches.

Limit switch

Sensor

2 Channel Output Unit SL-CH22, SL-CH22-PN

•

Two output devices are connectable: drive current 100mA max. each

•

SL-CH22(-PN) allows connection of two output devices,

and handles both signals. It can supply 100mA max. current

to each device, so that ordinary DC relays or solenoid

valves can be activated.

Beacon and relay

It handles two output signals to a bea-

con and a relay, two relays, or two sole-

noid valves.

Relay

Beacon

Application

I/O Arrayed Terminal Unit SL-TB䡺, SL-TB䡺-PN, SL-TBP䡺, SL-TBP䡺-PN, SL-TBP䡺-TY

•Screw-on terminal unit

•Depending upon the model, 4 Nos., 8 Nos. or 16 Nos. of input/output devices

(NPN/PNP type) can be connected to the terminal units.

Further, since power supply terminals for the input/output devices have been incor-

porated on all terminal units, neat wiring is possible.

•Output signal hold

•

The output arrayed terminal unit is incorporated with an output signal hold function,

which retains the output state just prior to an error on the signal transmission lines.

This limits the effect on an output device, should a failure occur.

•Separate load power supply type output terminal is now available

•

Separate load power supply type output terminal SL-TBP䡺-TY which enables forced

turning OFF of the output device connected to the output terminal without halting the

complete S-LINK system, by switching off the load power supply, in the event of the

output device failure, is now available.

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

Analog I/O Arrayed Terminal Unit SL-TBAD4, SL-TBDA1

•High resolution

•A high resolution of 1/4,000 (12 bits) can be realized.

•Fast data conversion

•They have a fast data conversion time of 1ms approx., for analog to digital, or digi-

tal to analog.

•Input range settable for each channel (SL-TBAD4)

•In case of the analog input arrayed terminal unit SL-TBAD4, it is possible to set

the input range for each input channel. As the analog input range can be 4 to

20mA, 1 to 5V, 0 to 10V orⳮ10 toⳭ10V, it can be selected according to the out-

put of the connected analog device.

Environment Resistant I/O Unit SL-TW4, SL-TW4-PN, SL-TW8, SL-TW8-PN, SL-TW2P2, SL-TW2P2-PN, SL-TWP4, SL-TWP4-PN

•Reliable design with IP67 protection

•It has IP67 (IEC 60529) protection, which

makes it safe even against water splashes.

Besides wire-saving in equipment/machin-

ery which requires waterproofing, it can be

used to simplify construction at places

where so far ‘water-resistant boxⳭcable

groundⳭterminal block’, etc., were used.

•Easy wiring with exclusive water-resistant connector

•M12 composite 4-pin connectors having IP67 protection are available for connec-

tion of the main cable, branch cables or I/O devices.

Troublesome soldering is absolutely not required, and cables of I/O devices can be

connected simply by a screwdriver. Four types of composite male connectors are

available to suit the cable diameter of different I/O devices.

Further, a branch connector which can not only branch the main cable easily, but

can also connect a set of emitter/receiver of a thru-beam type photoelectric sensor

(1 set) as 1 input channel, is available.

•‘T’-branch wiring and cascade wiring possible

•Main cable and branch cable can not only be ‘T’-branched, but can also be cas-

cade wired.

•Wide variety

•Four types of units are available:

input unit (4 or 8 inputs), I/O unit

(2 inputs and 2 outputs), or output

unit (4 outputs).

<‘T’-branch wiring><

Cascade wiring>

side IN

side

Cover for

M12 male

connector

(SL-WPK)

(Optional)

Cover for

M12 male

connector

(SL-WPK)

(Optional)

Branch connector

(SL-WY)(Optional) Branch connector

(SL-WY)(Optional)

side

OUT/

LOCAL

PWR side IN

side

OUT/

LOCAL

PWR side

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

I/O Unit Selectable According to the Application

Relay Output Terminal Unit SL-TPR4, SL-TPR8

•Output device control through

relays

•These are 4 channel and 8 channel

relay output terminal units.

The integrated relay can drive AC

actuators up to 250V 2A.

•Output signal hold

•The relay output terminal unit is incor-

porated with an output signal hold

function, which retains the output

state just before an error occurs on

the signal transmission lines.

This lim-

its the effect on an output device,

should a failure occur.

On-board I/O Module SL-M䡺, SL-MP䡺

•I/O interface for custom made PCB

•These are IC type modules with external address setting switches and indicators.

The modules are available as vertical mounting type and horizontal mounting type.

Selection can be made depending upon the custom PCB design and the compo-

nent space available.

Mounted PCB illustration

Custom made printed circuit board

To S-LINK and

I/O devices

Terminal block

Horizontal mounting type

Vertical mounting type

8 Channel Snap-connector I/O Unit SL-T8J, SL-T8J-PN, SL-TP8J, SL-TP8J-PN

•Output signal hold

•

The 8 channel snap-connector output

unit is incorporated with an output sig-

nal hold function, which retains the

output state just prior to an error on

the signal transmission lines. This lim-

its the effect on an output device,

should a failure occur.

•Snap male connector

•SL-CP1, for 0.08 to 0.2mm2conduc-

tors, SL-CP2, for 0.3mm2conductors,

and SL-CP3, for 0.5mm2conductors,

clamp the inner conductors of a

cable, and establish conduction sim-

ply by pressing, so that there is no

need to strip the wire insulation.

•8 input devices or 8 output devices

are connectable

•The slim and compact snap-connec-

tor I/O unit interfaces 8 input devices

or 8 output devices with the

S-LINK system. Its connections are

very easy with the snap male connec-

tors (optional).

35mm width

DIN rail

Snap male connector (Optional)

SL-CP1, SL-CP2 or SL-CP3

I/O device cable

8 channel snap-connector input unit SL-T8J(-PN)

8 channel snap-connector output unit SL-TP8J(-PN)

SL-CP1 or SL-CP2

I/O device cable

SL-CP3

I/O device cable

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

16 Channel MIL Connector I/O Unit SL-T16C1, SL-T16C1-PN, SL-TP16C1, SL-TP16C1-PN

•

16 I/Os connectable via a MIL connector

•

The slim and compact MIL connector I/O

unit connects 16 input/output devices to the

S-LINK system by a 20-pin MIL connector.

•

Matsushita Electric Works relay ter-

minals are connectable with MIL

connector cables (SL-T䡺16C1 only)

•RT2 relay terminal (AY23), PC relay

terminal (AY11)/PC terminal (AY10),

or CT-2 connector terminal (AYC)

manufactured by Matsushita Electric

Works are directly connectable via a

MIL connector cable as the pin

arrangements match.

35mm width

DIN rail (Optional)

20-pin MIL connector (male receptacle)

MIL-C-83503 conforming

AXM220001 manufactured by

Matsushita Electric Works

AXM120415 manufactured by

Matsushita Electric Works or equivalent

()

20-pin MIL connector

(female connector)(Optional)

20-core flat cable (Optional)

16 channel MIL connector input unit SL-T16C1(-PN)

16 channel MIL connector output unit SL-TP16C1(-PN)

RT-2 relay terminal manufactured by

Matsushita Electric Works (AY23)

16 inputs

16 outputs

Snap-connector Sensor Block SL-BMJ, SL-BXJ

•Snap female connector

•

SL-CJ1, for 0.08 to 0.2mm

con-

ductors, and SL-CJ2, for 0.3mm

conductors, clamp inner conductors

of a cable, and establish conduction

simply by pressing, so that there is

no need to strip the wire insulation.

•Combination with plug-in unit sensor blocks

•

The snap-connector sensor

block (main or extension) is com-

binable with the plug-in unit sen-

sor block (main or extension).

SL-BMJ can be followed by two

SL-BXs.

SL-BM can be followed by one

SL-BXJ.

Removable cover

Suitable for DIN rail

Operation

indicators

Extension connector

It can be ‘T’-branched on

the S-LINK cable

Input device cable

Extension block

SL-BXJ

Sensor main block

SL-BMJ

Snap female connector

SL-CJ1

(for 0.08 to 0.2mm2 conductors)

SL-CJ2

(for 0.3mm2 conductors)

1Ⳮ24V

20V

3Sensing output

4Self-diagnosis output

()

•Output signal hold

•

The 16 channel MIL connector output unit is

incorporated with an output signal hold func-

tion, which retains the output state just prior

to an error on the signal transmission lines.

This limits the effect on an output device,

should a failure occur.

•Max. 16 input devices are connectable

•

The snap-connector sensor block (main or extension) interfaces maximum

16 input devices, such as, sensors or switches, to the S-LINK system. Their

connections are very easy with the snap female connectors (optional).

Plug-in Unit Sensor Block SL-BM, SL-BX

Photoelectric

sensor Inductive proximity

sensor Limit switch

•Max. 16 sensors are connectable

•One plug-in unit sensor main block can be followed by

max.

three extension blocks, so that max. 16 plug-in units are

connectable.

•Plug-in units

•The following sensor units can be

plugged in on the sensor block.

Plug-in units

●Fiber sensor

•

Digital setting (Note1)

FX-D1J (Red LED)

•Auto-setting

FX-A1J (

Red LED

)

FX-A1GJ

(

Green LED

)

•Manual setting

FX-M1J (

Red LED

)

FX-M1GJ

(Green LED)

Various input devices

are connectable

●

Input terminal unit (Note 2)

●SL-TJ1

●

Amplifier-separated

inductive proximity

sensor

GA-14J

GA-15J

●

Amplifier-separated

photoelectric sensor

SU-7J

The sensor blocks can generate

the ORed self-diagnosis output of

all the connected sensors. But, in

this case, the first channel of the

sensor main block gets occupied.

Sensor main block

(SL-BM)

Extension block (SL-BX)

Max. three extension

blocks are connectable.

( )

Notes: 1) In case the digital setting fiber sensor FX-D1J is connected to the plug-in unit sensor block, Output 2 cannot be used.

Notes: 2) PNP output type sensor cannot be connected to input terminal unit SL-TJ1.

I/O Unit Selectable According to the Application

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

S-LINK Direct Hook-up Photoelectric Sensor SL-A䡺

•Direct hook-up to S-LINK cable

•

The sensor SL-A䡺can be hooked up to the

S-LINK cable without any interface.

•No interference

•A total of 128 sensors can be connected in

one S-LINK system without any interfer-

ence.

•Note: If sensors are mounted next to each other, their

addresses should be separated by 4, or more.

Booster SL-BS1A

•Cable extension to total 400m

•

The booster extends the S-LINK cable by 200m, to a total 400m length. Loop wiring is

also possible beyond the booster.

Controller

Booster

1Total 400m in series

2200m extension from a branch point

3Satellite loops around main loop

Controller Booster

200m 200m

Controller

200m

Booster

200m

Booster

200m

Booster

200m

Notes: 1) Cable extension may not be possible depending on the type and number of I/O devices connected.

Notes: 2) A maximum of seven boosters can be connected for one S-LINK control unit. However, one

booster can never be followed by another booster in series.

S-LINK Direct Hook-up Area Sensor SL-N15

•

Direct hook-up to S-LINK cable

•The area sensor SL-N15 can

be hooked up to the S-LINK

cable without any interface.

Conventionally, NA1-5 has

been interfaced by SL-CH21

with three branch points, but

SL-N15 allows you to hook up

the emitter and the receiver to

the S-LINK cable, without any

interface.

SL-CH21

I/O

SIDE

IN :G

OUT :R

SEND

NOT

USED

ADDRESS

OFF

SUNX

SL-CH21

SL-N15

NA1-5

One-touch hook-up

at any place.

Conventional

SL-N15

•All four types are available

10m (Infrared)

30m (Infrared)

(Red, with polarizing filters)

700m (Infrared)

Thru-beam type

Retroreflective type

Diffuse reflective type

SL-A11, SL-A13

SL-A19

SL-A12

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

•Simple hook-up

•No need to connect a cable on a terminal with screws.

Wire insulation stripping, and crimp contact fitting have

been inevitable until the S-LINK hook-up connector was

introduced. Using the hook-up connector saves your time

and space, and enables a flexible cable layout.

•Cable end connector optimum for cable termination available

•When cabtyre cable is used as the main cable, the end connector can be easily connected.

•Socket-branch hook-up connector SL-JK and SL-JK1

•

By connecting the socket-branch hook-up connector SL-JK

and SL-JK1 to the S-LINK

cable and using the snap male con-

nector SL-CP䡺, S-LINK devices can be connected very easi-

ly. They can also be disconnected easily when required.

S-LINK Hook-up Connector SL-J1A, SL-JK, SL-JK1, SL-J3A, SL-JE, SL-JE-RC

S-LINK branch cable

Cover

Housing

Cover

S-LINK

main cable

Just hook-up both

covers, each

holding an S-LINK

cable, and the

housing together.

mUse exclusive S-LINK cables.

Illustration of connected S-LINK devices

SL-CP2 (Black)

()

Sensor block SL-BM

Sensor block SL-BMJ

S-LINK direct hook-up

photoelectric sensor

SL-A䡺

SL-JK1 (Blue)

(for ‘T’-branch)

for 0.3mm2

conductors

Simple Construction

S-LINK exclusive cabtyre cable

(SL-CBM100, SL-CBM200)

Junction terminal block

(commercial product)

2 channel I/O unit

SL-CH21

Cable attached

end connector

(SL-JE-RC)

I/O arrayed terminal unit (SL-TB䡺, SL-TBP䡺)

Cable attached

end connector

(SL-JE-RC)

S-LINK exclusive cabtyre cable (SL-CBM100, SL-CBM200)

•Wire clamping in a snap

•SL-CJ1, for 0.08 to 0.2mm2conductors, and SL-CJ2, for

0.3mm2conductors, are used with SL-BMJ or SL-BXJ.

SL-CP1, for 0.08 to 0.2mm2conductors, SL-CP2, for

0.3mm2conductors, and SL-CP3, for 0.5mm2conductors,

are used with SL-T8J(-PN) or SL-TP8J(-PN) I/O unit and

SL-JK or SL-JK1 hook-up connector. Further, if SL-CP3 is

used, S-LINK I/O devices can be easily connected/discon-

nected from the main/branch cable. Moreover, 2-pin type

hook-up female connectors SL-CJ12 (for 0.08 to 0.2mm2),

SL-CJ22 (for 0.3mm2) and 2-pin type hook-up male con-

nectors SL-CP12 (for 0.08 to 0.2mm2), SL-CP22 (for

0.3mm2) are also available for extension of 2-wire I/O

devices. Wire clamping is easy. Just insert wires of the

cable into the specified holes of the connector and press.

There is no need to strip the wire insulation.

Snap female connector

Snap male connector

•Fastening of hook-up connector is simple and reliable

•

The S-LINK exclusive pliers make wiring with hook-up con-

nectors simple and reliable.

The spring slide-back mechanism improves the productivi-

ty. Ratchet mechanism type SL-JPD is also available.

Snap Connector SL-CJ1, SL-CJ2, SL-CJ12, SL-CJ22, SL-CP1, SL-CP2, SL-CP3, SL-CP12, SL-CP22

S-LINK Exclusive Pliers SL-JPS, SL-JPD, SL-JPE, SL-JPC

<4-pin type><4-pin type>

<2-pin type><2-pin type>

SL-CJ1 or SL-CJ2

I/O device

cable

SL-CP1 or SL-CP2

I/O device

cable

SL-CP3

I/O device

cable

SL-CJ12 or SL-CJ22

I/O device

cable

SL-CP12 or SL-CP22

I/O device

cable

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

•Easy wiring with exclusive water-resistant connector

•M12 composite 4-pin connectors having IP67 protection

are available for connection of the main cable, branch

cables or I/O devices.

Troublesome soldering is absolutely not required, and

cables of I/O devices can be connected simply by a

screwdriver. Four types of composite male connectors are

available to suit the cable diameter of different I/O

devices.

Further, a branch connector which can not only branch the

main cable easily, but can also connect a set of

emitter/receiver of a thru-beam type photoelectric sensor

(1 set) as 1 input channel, is available.

Water-resistant Connector SL-WP4, SL-WP5, SL-WP6, SL-WP8, SL-WJ8, SL-WY, SL-WE

•Easy input/output check

•A handy monitor which can check I/O devices is available.

The handy monitor can be hooked up to the S-LINK sig-

nal transmission lines at any place. I/O states can be

checked in batches of 16. The handy monitor is also

incorporated with the S-LINK controller functions, so that,

for example, it can perform an I/O check on conveyor sys-

tem segments, still under assembly, even without the

S-LINK controller.

Handy Monitor SL-HM1

Simple Construction

SL-WP4:

Suitable cable diameter

"3 to "4mm

SL-WP5:

Suitable cable diameter

"4 to "5mm

SL-WP6:

Suitable cable diameter

"5 to "6mm

•Branching of main/branch cable possible

•A branch connector which can be used to branch the

main/branch cable is available. Moreover, it can connect a

set of emitter/receiver of a thru-beam type photoelectric

sensor as 1 channel.

SL-WY

•Environment resistant end connector available

•

It is used when the environment resistant I/O unit SL-TW䡺

is connected at the end of the main cable.

SL-WE

IP67 4-pin

SL-WJ8:

Suitable cable diameter

"6 to "8mm

SL-WP8:

Suitable cable diameter

"6 to "8mm

Note: Although SL-HM1 incorporates the functions of the SL-CU1A con-

troller, PLC I/O connectors cannot be connected.

IP67 4-pin

No. of control points: S-LINK 128 pointsⴐNormal wiring 96 points

On the S-LINK side 64 inputs and 64 outputs (fixed), a total

of 128 points can be controlled and, by adding 3 Nos. of I/O

modules, a max. of 96 points can be controlled by normal

wiring.

•FP0-SL1 manufactured by Matsushita Electric Works

Extremely small, large cost reduction

The CPU unit of the PLC (programmable logic controller),

I/O module, PLC I/O connector and the S-LINK controller

functions are incorporated in an extremely small body of

W30⳯H90⳯D60mm. The space required is greatly

reduced and compactness can be achieved.

Further, large cost reduction can also be realized.

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

Manifold Electromagnetic Valves Suitable for S-LINK

•

‘T’-branch connection manifold electromagnetic valves

•Manifold electromagnetic valves capable of direct ‘T’-

branch connection to the S-LINK cable are available from

Koganei Corp., SMC Pneumatics and CKD Corp.

•Please contact Koganei Corp. (Humphry Products Company in

U.S.A. and Canada), SMC Pneumatics or CKD Corp. for details.

Controllers Suitable for S-LINK

• Controllers for S-LINK released by other companies!!

•Matsushita Electric Works, Mitsubishi Electric Corp., and

Toyoda Machine Works have released controllers incorpo-

rating S-LINK controller functions so that the S-LINK sys-

tem can be controlled without a separate S-LINK con-

troller.

Limit Switches Suitable for S-LINK

•Direct connection of limit switches to S-LINK system!!

•

Limit

switches which can be directly connected to the

S-LINK system transmission line by ‘T’-branch connection

are available from Matsushita Electric Works.

•Please contact Matsushita Electric Works for details.

Matsushita

Electric Works Mitsubishi

Electric Corp. Toyoda

Machine Works

Koganei Corp. CKD Corp. SMC Pneumatics

•Please contact Matsushita Electric Works, Mitsubishi Electric

Corp., and Toyoda Machine Works for details.

Matsushita Electric Works

S-LINK Family Products: Launched One After Another

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

Use of flexible cable for moving equipment

Extremely effective in

wire-saving with movable

equipment.

Sensor

Personal computer

Distributed Installation

Booster

S-LINK direct hook-up

photoelectric sensor Booster

PLC

S-LINK

controller

2 channel

input unit

S-LINK

hook-up

connector

Manifold

electromagnetic

valves suitable for

S-LINK

1 channel

I/O unit

(output usage)

24V DC

power supply

2 channel I/O unit

PLC I/O connectors

In a product transportation equip-

ment, there are many input and

output devices spread over various

places. Although wire-saving has

always been desired to reduce the

cost and shorten the time of instal-

lation, long distance transmission

and product reliability are essential.

S-LINK allows a cable length of

200m, normally, and 400m along with

a booster. The double code collation

check plus high noise immunity

enable signal transmission reliability.

Furthermore, the S-LINK tree wiring

architecture enables you to branch off

sub-trunk lines or branch lines and

hook-up input and output devices,

anywhere you like. Test and installa-

tion block-by-block, and layout change

after installation are quite simple jobs.

Parking garage AGV

The S-LINK system is very suitable to wire up car detection

sensors in a large parking garage.

It reduces wires and installation time.

The signal transmission to AGV from a stationary controller has been very difficult.

As the S-LINK system allows use of commercial cables in the system, the AGV

equipped with the sensors and actuators can be linked with the stationary controller

via one flexible cable. Besides, the S-LINK alarm capability, that generates an error

output for a cable break, enables quick repair and ensures the system reliability.

Conveyor

Easy hook-up

APPLICATIONS

This product does not possess control functions

needed for accident prevention or safety mainte-

nance. Handle safety related or emergency stop sig-

nals without passing them through the S-LINK sys-

tem due to fail-safe considerations.

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

PLC 1 channel

I/O unit (input usage)

S-LINK

hook-up

connector

Sensor blocks

with fiber sensors

Snap-connector

sensor blocks

Output arrayed terminal unit

S-LINK controller

Manifold

electromagnetic valves

suitable for S-LINK

24V DC

power supply

PLC I/O connector

2 channel I/O unit

Input arrayed terminal unit

2 channel

output unit

APPLICATIONS

Automatic assembly machine

In an automatic assembly machine,

there are many input and output

devices distributed in various tight

spaces. As the machine becomes

more complex, the task of reducing

the cable volume becomes more dif-

ficult. Wire-saving is the primary

requirement, but reliability of signal

transmission is also indispensable.

In the S-LINK loop wiring, the system

maintains signal transmission even

when the loop may break at any one

place. In the S-LINK standard wiring,

the controller reveals disconnected

device addresses when the signal

transmission line may break. Further,

even if excess current may flow by a

short-circuit between the signal

transmission lines, the controller

shuts down the entire system.

Plug-in connection

Parts delivery systemHandler

An IC handler uses many sensors. The S-LINK system

contributes in reducing wires in order to miniaturize the

machine.

In a parts-taking verification system, the parts shelves are

equipped with a number of area sensors at the front. The

inputs equal the number of shelves and if job indicators are

used, there are an equal number of outputs.

The S-LINK system wires up all the area sensors with

effective space and wire saving.

Integrated Installation

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

䢇Others

‘T’-branch multi-drop

wiring system

is the trademark of S-LINK.

Custom PCB

I/O modules

SL-CP䡺

SL-CJ䡺

SL-J1A

SL-JE-RC

SL-JE

SL-CP3

SL-J3A

SL-JK䡺

1234

3216

11248

163264

891011121314

01234567

SEND

ER1ER3ER4

DEC.(0l127)

HEX.(0l7F)

ADDRESS

UNIT COUNT

DISP.SELECT

SETINCREMENT

ADDRESS

TOP ADDRESS

OUTPUT MONITORDATA ON/OFF

DISABLE(OFF)

INPUT

OUTPUT

0V24V24V

8910111213141515

HANDY MONITOR

SL-HM1

ADDRESS

I/O TEST

(BK)(WH)(BU)(BN)

CONTROL

I/O CHECK

䢇Plug-in to PLC I/O modules

Use multi-core cable PLC I/O connectors when terminal

block type PLC is used for control.

Multi-core cable

PLC input unit

SL-S

Multi-core cable

PLC output unit

SL-P

Multi-core cable PLC

input unit (PNP)

SL-SP

Multi-core cable PLC

output unit (PNP)

SL-PP

PLC input connector

SL-S䡺

S-LINK controller

SL-CU1A

PLC output connector

SL-P䡺

䢇

Slot-in to MEW FP3/FP10S(H) series

FP3, FP10S, FP10SH series

Matsushita Electric

Works PLC bus

S-LINK controller

SL-FP3

Yokogawa Electric

PLC bus S-LINK

controller

SL-FAM3

S-LINK suitable controllers

FP0-SL1, FP2-SL2, FP2-C1SL

Supplied by Matsushita

Electric Works.

Matsushita Electric

Works PLC bus

S-LINK control board

SL-FPC

PC/AT S-LINK

control board

SL-PCAT

PCI bus S-LINK

control board

SL-PCI

NEC PC/FC-98

series S-LINK

control board

SL-PC98

VME bus S-LINK

control board

SL-VMES2

䢇

Transmission distance

extended from 200m to 400m

Booster

SL-BS1A

Further

200m

S-LINK direct

hook-up area sensor

SL-N15

S-LINK direct hook-up

photoelectric sensor

SL-A䡺

Power supply

24V DC

Ⳳ10%

S-LINK exclusive

flat cable

S-LINK exclusive cabtyre cable

SL-RCM100䡺/RCM200

4-core flat cable which can be easily

‘T’-branched.

SL-CBM100/CBM200

Connectors

Various S-LINK connectors

for simple cable connections.

I/O modules

SL-M8(F) (8 inputs)

SL-M16(F) (16 inputs)

SL-MP8(F) (8 outputs)

SL-MP16(F) (16 outputs)

SL-M4P4(F)

(4 inputs and 4 outputs)

I/O modules mountable

on your custom PCB.

Handy monitor

SL-HM1

S-LINK handy monitor performs

I/O check by connecting to any

point on the main/branch cable.

Further, it is also equipped with

S-LINK controller functions.

Local power supply

䡵 S-LINK control unit

䡵 S-LINK input devices

䡵 S-LINK output devices

Sharp PLC bus

S-LINK control board

SL-Z300

䡵 Direct hook-up sensors

䡵 Cables 䡵 Other S-LINK devices

OUTOUT

8 inputs are connectable.

IN IN IN IN

OUT OUT OUT OUT

8 outputs are connectable

OUT OUT OUT OUT

16 outputs are connectable

8 channel snap-

connector output unit

SL-TP8J

SL-TP8J-PN

16 channel MIL

connector output unit

SL-TP16C1

SL-TP16C1-PN

2 channel

output unit

SL-CH22

SL-CH22-PN

OUT OUT

2 outputs are

connectable

Supplied by Koganei Corp.,

SMC Corp. and CKD Corp.

S-LINK direct hook-up manifold

electromagnetic valves

Relay output terminal unit

SL-TPR4

SL-TPR8

Environment resistant I/O unit

Output arrayed terminal unit

SL-TBP䡺

SL-TBP䡺-PN

SL-TBP䡺-TY

4 outputs, 8 outputs, 16 outputs

Selectable from 4, 8 or

16 output models.

1 channel

I/O unit

SL-CH1

SL-CH1-PN

OUT

2 outputs

2 inputs

OUT

IN IN

2 inputs are connectable

Maximum 16

inputs can be

plugged in.

Plug-in unit

sensor main block

SL-BM

Fiber sensor

Amplifier-separated

photoelectric sensor

Amplifier-separated

inductive proximity sensor

Input terminal unit

䢇Plug-in units (4 units per block)

SL-TJ1

GA-14J, GA-15J

SU-7JFX-䡺J

Plug-in unit

extension block

SL-BX

8 inputs are connectable.

IN IN IN IN

Snap-connector

extension block

SL-BXJ

S-LINK direct hook-

up limit switch

Supplied by Matsushita

Electric Works.

IN IN IN IN

16 inputs are connectable

16 channel MIL

connector input unit

SL-T16C1

SL-T16C1-PN

8 channel snap-

connector input unit

SL-T8J

SL-T8J-PN

8 inputs are connectable.

IN IN IN IN

Maximum 16 inputs

can be connected.

Snap-connector

sensor main block

SL-BMJ

2 channel

I/O unit

SL-CH21

SL-CH21-PN

SL-CH21K

Environment resistant output unit

Analog output arrayed

terminal unit

SL-TBDA1

4 outputs, 8 outputs

Selectable from 4 or

8 output models.

Analog input arrayed

terminal unit

SL-TBAD4

Input arrayed

terminal unit

SL-TB䡺

SL-TB䡺-P

OUT

4 outputs

OUT

1 output

2 channel

input unit

SL-CH20

SL-CH20-PN

IN 4 inputs

4 inputs, 8 inputs, 16 inputs

Selectable from 4, 8

or 16

put models.

Either 1 output

or 1 input is

connectable

1 output and 1 input,

total 2 I/Os are

connectable.

SL-TWP4, SL-TWP4-PN

SL-TW2P2, SL-TW2P2-PN

Maximum 3 plug-in unit

extension blocks can

follow 1 plug-in unit

sensor main block.

( )

Environment resistant input unit

SL-TW4, SL-TW4-PN

SL-TW8, SL-TW8-PN

IN 4 inputs, 8 inputs

Selectable from 4 or 8

put models.

OUT

Indicates an

input device

Indicates an

output device

()

The number of and shows the number of

connections that can be made to that device.

Note: Please refer to P. 30, 31 for products compatible

with fieldbus networks

OUT

S-LINK is a wire-saving system which

allows connection to max. 128 I/O

devices by using one controller.

S-LINK SYSTEM CONFIGURATION EXAMPLE

Limit switch, photoelectric

sensor, inductive proximity

sensor, push-button switch,

cylinder switch, etc.

Lamp, buzzer, relay, electro-

magnetic valve, solenoid, etc.

SL-E

SL-F70

SL-F150

SL-F250

SL-F1000

SL-C1000

SL-C2000

SL-C5000

SL-C2000F

SL-S1

SL-S2

SL-S3

SL-S4

SL-S5

SL-S6

SL-S7

SL-P1

SL-P2

SL-P3

SL-P4

SL-P5

SL-P6

PLC

PLC I/O connectors

End

connector

Cascade cable

Control

cable

()

Max. four PLC I/O

connectors can be

cascaded with one

S-LINK controller.

PLC input connectors

PLC output connectors

(same shape)

The listed PLC I/O mod-

ules (NPN only) allow the

mating PLC I/O connec-

tor to be plugged on

them for signal transmis-

sion between the PLC

and the S-LINK con-

troller.

The PLC I/O connec-

tor converts I/O data

from serial to parallel,

and vice versa.

I/O points: 32 points

per connector

Matsushita

Electric Works

Toshiba

Machine Co.

Fuji Electric Co.

Mitsubishi

Electric

Corp.

Sharp Corp.

Omron Corp.

Yokogawa

Electric Corp.

Toshiba Corp.

Yasukawa Electric

Corp.

Hitachi

Yasukawa Electric

Corp.

FP3, FP10S

FP10SH

TC200

NS series

F55

F70

F80H,

F120H

F120S

F140S, F15XS

AnS

AnN, AnA, AnU

QnA, QnAs

A2CJ

JW20, JW20H

JW30H

JW50H

CVM1,CV,C500

C1000H,C2000H

C200H series

CQM1

FA500

FA-M3

GL20,GL40S,GL60S

GL60H,GL70H

H series

GL20,GL40S,GL60S

GL60H,GL70H

AFP33027

TC64DI

NS-X64-1

NS-XY64-1 (X side)

NV1X3204

NV1X3204-W

NV1X3206

NC1X3204

NC1X3204-3

NC1X3206

NC1X6404

NC1X6406

NC1W6406T(X side)

FTU125A

FTU126A

FTU127C

FTU612A (X side)

A1SX41

A1SX42

A1SH42 (X side)

AX42

AH42 (X side)

AJ35TC1-32D

JW-234N

JW-264N

JW-34NC

JW-64NC

C500-ID219

C200H-ID216

C200H-ID217

CQM1-ID213

XD64-6N

WD64-6N (X side)

F3XD32-3N

F3XD64-3N

DI-335

DI-335H

XDC24D2H

B2605

AFP33487

TC64DON

NS-Y64-T1

NS-XY64-1 (Y side)

NV1Y32T05P1

NC1Y32T05P1

NC1Y64T05P1-1

NC1W6406T(Y side)

FTU222A

FTU227C

FTU612A (Y side)

A1SY41

A1SY42

A1SH42 (Y side)

AY42

AH42 (Y side)

AJ35TC1-32T

JW-232S

JW-262S

JW-32SC

JW-62SC

C500-OD213

C200H-OD218

C200H-OD219

CQM1-OD213

YD64-1A

WD64-6N (Y side)

F3YD32-1A

F3YD64-1A

DO-335

B2604

YTR24DH

Designation Appearance (Note1) Model No. Description

For input For output Manufacturer PLC

PLC input PLC output

module (Note 4) module (Note 4)

It must be connected at the end of the last PLC

I/O connector.

It links two PLC I/O con-

nectors.

It links the S-LINK con-

troller and the first PLC

I/O connector.

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

ORDER GUIDE

PLC related units

Control cable

Cascade

cable

End connector

Length: 70mm

Length: 150mm

Length: 250mm

Length: 1,000mm

Length: 1m

Length: 2m

Length: 5m

Length: 2m

Notes: 1) Components with ‘ ’ mark conform to the CE marking EMC Directive.

However, note that for the PLC I/O connectors to conform to CE marking EMC Directive, it is necessary to use cascade cable SL-F70, SL-F150 or

SL-F250 and control cable SL-C2000F.

Notes: 2) The PLC I/O connectors use Fujitsu connectors. However, SL-S1, SL-P1, SL-S6 and SL-P6 connectors use MIL connectors.

Notes: 3) PLC I/O connectors are connectable to S-LINK controller SL-CU1A only.

Notes: 4) X side and Y side indicate the input and the output connectors, respectively, of the compound input/output module.

PLC input

connector

PLC output

connector

(Note 2, 3)

Fujitsu con-

nector specs. MIL connec-

tor specs.

Designation Appearance (Note) Model No. Description

Multi-core

cable PLC

I/O unit

NPN typePNP type

Multi-core

cable

For input For output

SL-S SL-P

SL-SP SL-PP

SL-L2000F

The multi-core cable PLC I/O unit, connectable with

any type of screw-on terminal type PLC I/O module via

the multi-core cable, interfaces I/O data between the

S-LINK controller and PLC.

It includes the I/O data conversion circuit for serial to

parallel or parallel to serial conversion.

I/O points: 32 points per unit

Connection to screw-on terminal type PLC is by an

optional multi-core cable attached with an MIL connec-

tor on one end.

The multi-core cable attached with an MIL

connector on one end links the multi-core

cable PLC I/O unit to a screw-on terminal

type PLC I/O module.

Length: 2m

Multi-core

cable

Multi-core cable

PLC I/O unit

PLCPLC

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

ORDER GUIDE

PLC related units

Note: Components with ‘ ’ mark conform to the CE marking EMC Directive.

However, note that for the multi-core cable PLC I/O units to conform to CE marking EMC Directive, it is necessary to use cascade cable SL-F70, SL-F150

or SL-F250, control cable SL-C2000F and multi-core cable SL-L2000F.

S-LINK control units

Designation Appearance (Note) Model No. Description

SL-CU1A

SL-VMES2

SL-PCI

SL-PCAT

SL-PC98

SL-FP3

SL-FAM3

SL-FPC

SL-Z300

It supplies the synchronization signal to the complete system to send and

receive I/O data from external devices correctly. It also monitors the signal

transmission line, and specifies the addresses of the disconnected devices if

the line breaks, etc.

S-LINK controller

VME bus S-LINK

control board

PCI bus S-LINK

control board

NEC PC/FC-98

series S-LINK

control board

PC/AT S-LINK

control board

Matsushita Electric

Works PLC bus

S-LINK controller

Sharp PLC bus

S-LINK control

board

Matsushita Electric

Works PLC bus

S-LINK control board

Yokogawa Electric

PLC bus S-LINK

master unit

It can be fitted into the expansion slot (ISA bus) of PC/AT series or compatible

to control the S-LINK system

By using this control board, the SL-CU1A controller, the PLC I/O connec-

tors, and their link cables are not required.

( )

It can be directly connected to the bus line of the FP3, FP10S or FP10SH series

PLCs manufactured by Matsushita Electric Works to control the S-LINK system.

By using this controller, not only the SL-CU1A controller, the PLC I/O

connectors, and their link cables, but also the PLC I/O modules are not

required.

(

It can be directly connected to the VME bus line to control the S-LINK sys-

tem. It provides two S-LINK ports, each allowing 128 I/O points maximum,

so that a total of 256 I/O points can be controlled.

By using this control board, the SL-CU1A controller, the PLC I/O connec-

tors, and their link cables are not required.

It can be directly connected to the bus line of the FA-M3 PLC manufactured

by Yokogawa Electric to control the S-LINK system.

By using this master unit, not only the SL-CU1A controller, the PLC I/O

connectors, and their link cables, but also the PLC I/O modules are not

required.

( )

It can be fitted into the expansion slot (PCI bus) of a personal computer

control the S-LINK system

By using this control board, the SL-CU1A controller, the PLC I/O connec-

tors, and their link cables are not required.

( )

It can be fitted into the expansion slot (C bus) of NEC PC/FC-98 series to

control the S-LINK system.

By using this control board, the SL-CU1A controller, the PLC I/O connec-

tors, and their link cables are not required.

( )

It can be directly connected to the bus line of the FP-C PLC manufactured by

Matsushita Electric Works to control the S-LINK system.

By using this control board, not only the SL-CU1A controller, the PLC I/O

connectors, and their link cables, but also the PLC I/O modules are not

required.

( )

)

( )

It can be directly connected to the bus line of the J-board Z-300 series PLC

manufactured by Sharp to control the S-LINK system.

By using this control board, not only the SL-CU1A controller, the PLC I/O

connectors, and their link cables, but also the PLC I/O modules are not

required.

( )

Note: Components with ‘ ’ mark conform to the CE marking EMC Directive.

S-LINK I/O devices

SL-GU1-D

SL-GU1-P

SL-GU1-I

SL-GU1-C

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

ORDER GUIDE

Products for fieldbus network

S-LINK gateway

controller for

DeviceNet

S-LINK gateway

controller for

PROFIBUS-DP

S-LINK gateway

controller for

INTERBUS

S-LINK gateway

controller for

CC-Link

S-LINK gateway

controller for

JPCN-1/

RS-485

JPCN-1/RS-485

master board for

PC/AT

JPCN-1/RS-485

master board for

PC/FC-98 series

JPCN-1/RS-485

master board for

PC/104 bus

SL-CU1-485

SL-PCAT-485

SL-PC98-485

SL-PC104-485

S-LINK gateway controller for connection to open network DeviceNet, widely

used in the United States.

S-LINK gateway controller for connection to open network PROFIBUS-DP,

widely used in Europe.

S-LINK gateway controller for connection to open network INTERBUS,

widely used in Europe.

S-LINK gateway controller for connection to fieldbus network CC-Link, pro-

moted by Mitsubishi Electric Corp.

S-LINK gateway controller for connection to open network JPCN-1, widely

used in Japan. It incorporates S-LINK system control functions and slave

functions conforming to JPCN-1 or RS-485 so that it can connect an S-LINK

system to a JPCN-1 or RS-485 communication system.

It can be installed in the extension slot (ISA bus) of a PC/AT or compatible so that the personal

computer can be used as a JPCN-1 master.

It incorporates the S-LINK mode (for RS-485 communication) which enables easy control of the

S-LINK system and the JPCN-1 mode which enables control of JPCN-1 conforming devices.

It can be installed in the extension slot (C bus) of an NEC PC/FC-98 series so that the personal

computer can be used as a JPCN-1 master.

It incorporates the S-LINK mode (for RS-485 communication) which enables easy control of the

S-LINK system and the JPCN-1 mode which enables control of JPCN-1 conforming devices.

It can be installed in the personal computer or board computer of a PC/104 bus so that the per-

sonal computer or board computer can be used as a JPCN-1 master.

It incorporates the S-LINK mode (for RS-485 communication) which enables easy control of the

S-LINK system and the JPCN-1 mode which enables control of JPCN-1 conforming devices.

1 channel I/O unit

2 channel I/O unit

2 channel input unit

2 channel output unit

8 channel snap-

connector input

unit

8 channel snap-

connector out-

put unit

16 channel MIL

connector input

unit

16 channel MIL

connector out-

put unit

Connector I/O unit

SL-CH1

SL-CH1-PN

SL-CH21

SL-CH21-PN

SL-CH21K

SL-CH20

SL-CH20-PN

SL-CH22

SL-CH22-PN

SL-T8J

SL-T8J-PN

SL-TP8J

SL-TP8J-PN

SL-T16C1

SL-T16C1-PN

SL-TP16C1

SL-TP16C1-PN

NPN type

PNP type

NPN type

PNP type

Photocoupler

isolation

(NPN) type

NPN type

PNP type

NPN type

PNP type

NPN type

PNP type

NPN type

PNP type

NPN type

PNP type

NPN type

PNP type

It can be used as either an input unit or an output unit by

switch selection. Hence, a sensor, limit switch, etc., is con-

nectable when it is used as an input, and a relay, lamp,

etc., is connectable when it is used as an output.

1 input and 1 output device are connectable.

It is suitable for power supply remote control func-

tion of NEC FA personal computer FC-98/FC98-NX

series.

2 input devices are connectable.

2 output devices are connectable.

8 input or 8 output devices are connectable with snap

male connectors.

The output unit is incorporated with an output signal hold

function, which retains the output state just prior to an

error on the signal transmission line.

Since connection can be made with an MIL connector, 16

input or 16 output devices can be connected to this slim

I/O unit.

The output unit is incorporated with an output signal hold

function, which retains the output state just prior to an

error on the signal transmission line.

Designation Appearance (Note) Model No. Description

Note: Components with ‘ ’ mark conform to the CE marking EMC Directive.

(Excluding SL-CH21K)

4 NPN inputs

4 PNP inputs

8 NPN inputs

8 PNP inputs

4 NPN outputs

4 PNP outputs

SL-TW4

SL-TW4-PN

SL-TW8

SL-TW8-PN

SL-TW2P2

SL-TW2P2-PN

SL-TWP4

SL-TWP4-PN

2 NPN inputs and

2 NPN outputs

2 PNP inputs and

2 PNP outputs

SL-TB4

SL-TB4-PN

SL-TB8

SL-TB8-PN

SL-TB16

SL-TB16-PN

SL-TBP4

SL-TBP4-PN

SL-TBP8

SL-TBP8-PN

SL-TBP16

SL-TBP16-PN

SL-TBP4-TY

SL-TBP8-TY

SL-TBP16-TY

4 NPN inputs

4 PNP inputs

8 NPN inputs

8 PNP inputs

16 NPN inputs

16 PNP inputs

4 NPN outputs

4 PNP outputs

8 NPN outputs

8 PNP outputs

16 NPN outputs

16 PNP outputs

4 NPN oututs

8 NPN outputs

16 NPN outputs

They are screw-on terminal units to which 4, 8 or 16 input

devices are connectable. Since power supply terminals

have been provided for each input channel, neat wiring is

possible.

They are screw-on terminal units to which 4, 8 or 16

output devices are connectable. The output unit is

incorporated with an output signal hold function, which

retains the output state just prior to an error on the signal

transmission line.

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

ORDER GUIDE

S-LINK I/O devices

I/O arrayed terminal unit

Analog I/O arrayed terminal unit

Environment resistant I/O unit

Designation Appearance (Note) Model No. Description

Output terminal

Input terminal

Output terminal

Input unit

I/O unit

Output unit

They enable forced turning OFF of the output

device connected to the output terminal without

halting the complete S-LINK system, by

switching off the load power supply.

This is an analog input terminal unit which can connect

4 devices having an analog output.

This is an analog output terminal unit which can connect

one device requiring an analog input. It is incorporated

with an output signal hold function, which retains the

output state just prior to an error on the signal

transmission line.

These are units which can connect 4 or 8 input devices.

They feature IP67 (IEC 60529) protection, which can

withstand water splashes. The input devices can be easily

connected by using optional composite connectors.

These are units which can connect 2 inputs and 2 outputs.

They feature IP67 (IEC 60529) protection, which can

withstand water splashes.

They are incorporated with an output signal hold function,

which retains the output state just prior to an error on the

signal transmission line.

These can connect 4 output devices.

They feature IP67 (IEC 60529) protection, which can

withstand water splashes.

They are incorporated with an output signal hold function,

which retains the output state just prior to an error on the

signal transmission line.

SL-TBAD4 4 inputs

1 output

SL-TBDA1

Input terminal

Separate

load power

supply type

Note: Components with ‘ ’ mark conform to the CE marking EMC Directive.

Sensor

main block

They are terminal units to which 4 or 8 output devices can

be connected by slim socket relays that can be easily

replaced. They are incorporated with an output signal hold

function which retains the output state just prior to an error

on the signal transmission line.

4 outputs

(Note 2)

8 outputs

(Note 2)

Plug-in unit

Auto-setting

fiber sensor

Manual setting

fiber sensor

Amplifier-

separated

photoelectric

sensor

Amplifier-

separated

inductive

proximity

sensor

One-touch

clamping type

Screw

tightening

type

Input terminal

unit

Designation Appearance (Note1) Model No. Description

Its thickness is merely 10mm. The incident light intensity

and the threshold value can be seen at a glance from the

backlit LCD. Further, threshold value setting is simple by

using the industry’s first jog switch.

(For details, refer to P.64lfor the FX-D1 series.)

Its thickness is merely 10mm. The sensitivity setting is

simple by using the industry’s first jog switch. Level

indicators, comprising of 10 LEDs, which enable

confirmation of the set sensitivity at a glance, have been

incorporated.

(For details, refer to P.64lfor the FX-A1 series.)

Its thickness is merely 10mm. Since the sensitivity setting

is done by a 12-turn potentiometer, fine setting is possible.

(For details, refer to P.64lfor the FX-M1 series.)

Red LED

Green LED

Red LED

Green LED

FX-A1J

FX-A1GJ

FX-M1J

FX-M1GJ

FX-D1J

SL-TJ1

SU-7J

GA-14J

GA-15J

Its thickness is merely 10mm. The sensitivity is automatically set with ease.

12 kinds of sensor heads are suitable with it.

(For details, refer to P.350lfor the SU-7 series.)

Its thickness is merely 10mm. The sensitivity is so precisely set with the 18-

turn adjuster that the sensor is suitable for sophisticated applications with a

high repeatability of 1!m or less.

(For details, refer to P.686lfor the GA-10 series.)

It allows connection of 1 No. of various kinds of input devices, such as, a

photoelectric sensor, an inductive proximity sensor or a limit switch.

SL-TPR4

SL-TPR8

SL-BMJ

SL-BXJ

SL-BM

SL-BX

It allows connection of various kinds of input devices, such as, photoelectric

sensors, inductive proximity sensors, limit switches, and push buttons with

the snap female connectors. One SL-BMJ can be extended by one SL-BXJ

or two SL-BXs, up to 16 input points.

It can generate the ORed self-diagnosis output of all the connected

devices. In this case, the first channel gets occupied.

Sensor

main block

4 relay output

8 relay output

Extension

block

Snap-connector

For plug-in unit

Sensor block Relay output

terminal unit

It can follow either main block, and allows connection of 8 input devices.

It allows connection of various kinds of plug-in units of fiber sensors,

amplifier-separated photoelectric sensors, amplifier-separated inductive

proximity sensors and input terminal units. One SL-BM can be extended by

three SL-BXs or one SL-BX plus one SL-BXJ, up to 16 input points.

It can generate the ORed self-diagnosis output of all connected units. In

this case the first channel gets occupied.

It can follow either main block, and allows connection of four plug-in units.

( )

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

ORDER GUIDE

S-LINK I/O devices

Notes: 1) Components with ‘ ’ mark conform to the CE marking EMC Directive.

Notes: 2) Relay output is

‘

Contact a’ only. Further, when replacing the relay, use PA relay (APA 3312) made by Matsushita Electric Works.

Notes: 3) Output 2 cannot be used when connection is made to the plug-in unit sensor block.

Extension

block

Digital setting

fiber sensor

(Note 3)

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

ORDER GUIDE

S-LINK I/O devices

8 inputs

16 inputs

4 inputs and

4 outputs

These are IC type modules which enable external

connection of address setting switches and operation

indicators. They increase the design flexibility.

8 outputs

16 outputs

4 inputs and

4 outputs

8 inputs

16 inputs

8 outputs

16 outputs

SL-M8

SL-M16

SL-MP8F

SL-MP16F

SL-M4P4F

SL-MP8

SL-MP16

SL-M8F

SL-M16F

SL-M4P4

Input

module

I/O mixed

module

Output

module

Input

module

I/O mixed

module

Output

module

I/O module

Vertical typeHorizontal type

Designation Appearance Model No. Description

S-LINK direct hook-

up photoelectric

sensor

Thru-beam type 10m

Thru-beam type 30m

Retroreflective type with

polarizing filters 0.1 to 5m

Diffuse reflective type

700mm

These can be hooked up to the S-LINK cable, at

any place, without any interface.

Sensing range: 0.2 to 3m

0.05 to 1m when the

switch is set to SHORT

•Beam pitch: 25mm

•Sensing height: 100mm

•Sensing object:

"35mm or more

opaque object

It is a parts-taking verification sensor with five

sensing beams and can be hooked up to the

S-LINK cable without any interface.

Both the emitter and the receiver are incor-

porated with bright orange LED job indicators

that are easily visible to the operator.

SL-A11

SL-A13

SL-A19

SL-A12

SL-N15

S-LINK direct hook-

up area sensor

Retroreflective type with

polarizing filters

Thru-beam type

Diffuse reflective type

()

SL-CJ12 (White)

(1 set: 10 Nos.)

SL-JK1

(Blue)

(1 set: 10 Nos.)

Designation Appearance Model No. Description

Hook-up connector

Cable extension

hook-up connector

End hook-up

connector

Cable attached end

connector

Cable end socket-

branch hook-up

connector

Socket-branch hook-

up connector

4-pin type snap

female connector

2-pin type snap

female connector

2-pin type snap

male connector

SL-J1A

(Gray)

(1 set: 10 Nos.)

SL-J3A

(Black)

(1 set: 10 Nos.)

SL-JE

(Gray)

(1 set: 5 Nos.)

SL-JE-RC

(Gray)

(1 set: 1 No.)

SL-JK

(Light blue)

(1 set: 10 Nos.)

SL-CJ1 (White)

(1 set: 10 Nos.)

SL-CJ2 (Black)

(1 set: 10 Nos.)

SL-CP1 (White)

(1 set: 10 Nos.)

SL-CP2 (Black)

(1 set: 10 Nos.)

SL-CP12 (White)

(1 set: 10 Nos.)

SL-CP22 (Black)

(1 set: 10 Nos.)

It creates a ‘T’-branch connection between two S-LINK exclusive flat cables.

For 0.5mm2flat cable to 0.5mm2flat cable connection

It can extend the S-LINK exclusive flat cable.

For 0.5mm2flat cable to 0.5mm2flat cable connection

It must be connected at the end of the main cable.

For 0.5mm2flat cable

When cabtyre cable is used as the main cable, the end connector can be

easily connected.

It enables one I/O device to be connected at the S-LINK exclusive flat cable

end with the snap male connector SL-CP1, SL-CP2 or SL-CP3.

For 0.5mm2flat cable

It enables one I/O device to be branched off in the middle of the S-LINK

exclusive flat cable with the snap male connector SL-CP1, SL-CP2 or SL-CP3.

For 0.5mm2flat cable

It can be plugged into the socket of SL-BMJ or SL-BXJ to

connect an input device, or into the snap male connector

SL-CP1, SL-CP2 or SL-CP3 to extend the cable length.

It can be used for cable extension of 2-wire I/O devices by

combining with a snap male connector SL-CP12 or

SL-CP22.

It can used for cable extension of 2-wire I/O devices by

combining with a snap female connector SL-CJ12 or

SL-CJ22.

For 0.08 to 0.2mm

Wire dia.: "0.7 to "1.2mm

For 0.3mm

Wire dia.: "1.1 to "1.6mm

For 0.08 to 0.2mm

Wire dia:

0.7 to

1.2mm

For 0.3mm

Wire dia:

1.1 to

1.6mm

For 0.5mm

Wire dia.:

1.7 to

2.5mm

4-pin type snap

male connector

1234

It can be plugged into the socket of SL-T8J or SL-TP8J to

connect an I/O device, or into the socket-branch hook-up

connector SL-JK or SL-JK1 to connect an S-LINK direct

hook-up sensor.

Using SL-CP3, S-LINK I/O devices (with 0.5mm2cable)

can be easily connected/ disconnected from the

main/branch cable.

For 0.08 to 0.2 mm

Wire dia.: "0.7 to "1.2mm

For 0.3mm

Wire dia.: "1.1 to "1.6mm

SL-CJ22 (Black)

(1 set: 10 Nos.)

SL-CP3

(Greenish blue)

(1 set : 10 Nos.)

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

ORDER GUIDE

Connectors

1234

For 0.08 to 0.2mm

Wire dia.:

0.7 to

1.2mm

For 0.3mm

Wire dia.:

1.1 to

1.6mm

NOTE

The connectors are supplied in sets of 10 Nos. (SL-JE: 5 Nos., SL-JE-RC: 1 No.)

Please order in units of 10 Nos. (SL-JE: 5 Nos., SL-JE-RC: 1 No.)

(e.g.) In case 30 Nos. of SL-J1A are required, order SL-J1A⳯3 (sets).

For 0.18 to 0.75mm

Wire dia.: "3 to "4mm

For 0.18 to 0.75mm

Wire dia.: "4 to "5mm

For 0.18 to 0.75mm

Wire dia.: "5 to "6mm

For 0.3 to 0.75mm

Wire dia.: "6 to "8mm

For 0.3 to 0.75mm

Wire dia.: "6 to "8mm

This is a connector for branching of the main/branch cable and for connection

of the thru-beam type photoelectric sensor to the environment resistant I/O

unit SL-TW䡺.

It is connected when the environment resistant I/O unit SL-TW䡺is used at

the end of the main cable.

These are composite male connectors for connection of

input or output devices to the environment resistant I/O unit

SL-TW䡺, and for connection to the branch connector

SL-WY or the composite female connector SL-WJ8.

These are composite female connectors for connection to

the main cable side of the environment resistant I/O unit

SL-TW䡺, and for connection to the branch connector

SL-WY or the composite male connector SL-WP䡺.

Designation Appearance Model No. Description

Water resistant connector

Composite

male connector

Composite

female connector

Branch

connector

Environment

resistant end

connector

SL-WP4

(1 set: 10 Nos.)

SL-WP5

(1 set: 10 Nos.)

SL-WP6

(1 set: 10 Nos.)

SL-WP8

(1 set: 10 Nos.)

SL-WJ8

(1 set: 10 Nos.)

SL-WY

(1 set: 5 Nos.)

SL-WE

(1 set: 1 No.)

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

ORDER GUIDE

Connectors

NOTE

The connectors are supplied in sets of 10 Nos. (SL-WY: 5 Nos., SL-WE: 1 No.)

Please order in units of 10 Nos. (SL-WY: 5 Nos., SL-WE: 1 No.)

(e.g.) In case 30 Nos. of SL-WP4 are required, order SL-WP4⳯3 (sets)

Optional units

Designation Appearance (Note) Model No. Description

Booster

Handy monitor

Note: Components with ‘ ’ mark conform to the CE marking EMC Directive.

SL-BS1A

SL-HM1

It can extend the signal transmission distance by 200m.

A maximum of seven boosters can be connected for one S-LINK control unit.

However, one booster can never be followed by another booster in series.

It can be connected at any place on the signal transmission line and the I/O

states can be checked in batches of 16.

The handy monitor is also incorporated with the S-LINK control functions, so

that, for example, it can perform an I/O check on conveyor system

segments, still under assembly, even without the S-LINK controller.

MS-SLH

(1 set: 5 Nos.)

SL-MA2

(1 set: 20 Nos.)

SL-WJK

(1 set: 10 Nos.)

SL-WPK

(1 set: 10 Nos.)

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

Others

Designation Appearance Model No. Description

S-LINK exclusive

flat cable

S-LINK exclusive

cabtyre cable

S-LINK exclusive

pliers

S-LINK exclusive

ratchet pliers

SL-CP3 exclusive

pliers

SL-CJ1/2/12/22 and

SL-CP1/2/12/22

exclusive pliers

Cover for M12

male connector

Cover for M12

female connector

Marking plate

Address label

Length: 100m

Length: 200m

S-LINK exclusive flat cable (4-core)

•Conductor cross-section area: 0.5mm2

•Outer diameter: "2.5mm⳯4

SL-RCM100

SL-RCM100-PK

SL-RCM100-GN

SL-RCM100-GY

SL-RCM200

SL-CBM100

SL-CBM200

Length: 100m

Length: 200m

D line: White

with pink stripe

D line: White

with green stripe

D line: White

with gray stripe

S-LINK exclusive cabtyre cable (4-core)

•Conductor cross-section area: 0.5mm2

•Outer diameter: "7.4mm

SL-JPS

SL-JPD

SL-JPE

SL-JPC

Hook-up connector (SL-J䡺) can be connected in one grip.

Because of the ratchet mechanism, hook-up connector (SL-J䡺) can be

simply connected in one grip.

Snap male connector (SL-CP3) can be connected in one grip.

Hook-up connector (SL-CJ1/2/12/22, SL-CP1/2/12/22) can be connected in

one grip.

Make sure to put it on the unused main cable side connectors of the

environment resistant I/O unit SL-TW䡺.

Make sure to put it on the unused I/O side connectors of the environment

resistant I/O unit SL-TW䡺.

It is used to write the I/O device No., address No., etc., on the environment

resistant I/O unit SL-TW䡺.

It is used to mount the SL-CH䡺unit.

By sticking the labels on the respective S-LINK devices, the set addresses

can be confirmed at one glance.

SL-MA1-SET is available in white, pink, green and gray colors, as a 4-sheet

set, and is convenient when used by matching the color with that of the

S-LINK exclusive flat cable (100m type).

I/O unit holder for

SL-CH䡺

NOTE

The connectors are supplied in sets of 10 Nos., the marking plate in sets of 20 Nos., the I/O unit holder

for SL-CH䡺in sets of 5 Nos. and t

he address seal in sets of 4 sheets.

Please order in units of 10 Nos., 20 Nos., 5 Nos. or 4 sheets, respectively.

(e.g.) In case 10 Nos. of MS-SLH are required, order MS-SLH⳯2 (sets).

In case 8 sheets of SL-MA1-SET are required, order SL-MA1-SET⳯2 (sets).

SL-MA1-SET

(1 set: 4 sheets)

ORDER GUIDE

NOTE

The slit mask for SL-N15 is supplied in sets of 10 sheets.

Please order in units of 10 sheets.

(e.g.) In case 20 sheets of OS-NA1-5 are required, order

OS-NA1-5⳯2 (sets).

S-LINK

WIRE-SAVING SYSTEMS

SL-BMW/BW

Simple Wiring

S-LINK

‘T’-branch Multi-drop

OPTION

Designation Model No. Description

Sensor mounting

bracket for SL-A䡺

Sensor mounting

bracket for SL-N15

Sensor protec-

tion bracket for

SL-N15

Reflector mount-

ing bracket

Slit mask for

SL-N15

Connector I/O unit

mounting bracket

MS-NX5-1

MS-NX5-2

MS-NX5-3

MS-NA1-1

MS-NA2-1

MS-NA3

MS-RF23

OS-NA1-5

(1 set: 10 sheets)

MS-DIN-3

Foot angled mounting bracket

(The thru-beam type sensor needs two brackets.)

Foot biangled mounting bracket (sensor protection bracket)

(The thru-beam type sensor needs two brackets.)

Back angled mounting bracket

(The thru-beam type sensor needs two brackets.)

Four bracket set

Four M4 (length 15mm) screws with

washers, eight nuts, four hooks, four

spacers and eight M4 (length

18mm) screws with washers are

attached.

(Spacers are not attached with MS-NA1-1.)

It protects the sensor body.

Two bracket set

Four M4 (length 15mm) screws with

washers, and four nuts are attached.

For RF-230

The seal type slit mask restrains the

amount of beam emitted or received.

It is a DIN rail mounting bracket which

can be fitted on the mounting base of

SL-T8J(-PN), SL-TP8J(-PN), SL-T16C1(-PN)

and SL-TP16C1(-PN).

MS-NA1

M4 screws with washers, nuts

and hooks are attached.

M4 screws with washers, nuts,

hooks and spacers are attached.

MS-NA2

M4 screws with washers and, nuts are attached.

Two M4 (length 10mm)

screws with washers

are attached.

Sensor protection bracket

for SL-N15 Reflector mounting bracket

Slit mask for SL-N15 Connector I/O unit

mounting bracket

Sensor mounting bracket for SL-N15

•MS-NA1-1 •MS-NA2-1

Sensor mounting bracket for SL-A䡺

•MS-NX5-1 •MS-NX5-2 •MS-NX5-3

Since the slit mask is seal

type, it can be used by stick-

ing it to the detection surface.

Take care that the sensing

range will be reduced when

the slit mask is used.

Please contact our office for

details.

Two M4 (length 25mm)

screws with washers

and two M4 nuts are

attached.

Two M4 (length 25mm)

screws with washers

and two M4 nuts are

attached.

Two M4 (length 25mm)

screws with washers

and two M4 nuts are

attached.

Please refer to the S-LINK Design Manual for the specifications and dimensions of the S-LINK

devices.