2
+SENSE (8)
TRIM (7)
- SENSE (6)
TRIM UP
TR IM D OWN
+SENSE (8)
TRIM (7)
- SENSE (6)
10K ohm s
TRIMPOT
SPECIFICATIONS
All Specifications Typical At Nominal Line, Full Load, and 25℃ Unless Otherwise Noted
INPUT SPECIFICATIONS: GENRAL SPECIFICATIONS:
Input Voltage Range ....…………….......... 12V ..................... 9-18V Efficiency .................…..................................……..........…....... See Table
24V ....................... 18-36V Isolation Voltage .................... Input/Output ....………...….. 1500VDC min.
48V ........……........ 36-75V Input/Case .………..…….….. 1500VDC min.
Input Surge Voltage (100ms max.) …….….… 12V …........... 25Vdc max. Output/Case ………………… 1500VDC min.
24V ............… 50Vdc max. Isolation Resistance .............................…......... ...... ......…….... 1 07 ohm min.
48V ..….……. 100Vdc max Isolation Capacitance …………………..…………………....…… 1000pF Typ.
Undervoltage lockout : Switching Frequency ....... (12/24)Vin .………….............. 400KHz, Typ.
12Vin ….………… power up ---->8.8V, power down ----->8V 48Vin ........................................ 300KHz, Typ.
24Vin …………… power up ---->17V, power down ----->16V Operating Case Temperature …………………………….. -40℃ to 100℃
48Vin ….……… power up ---->34V, power down ----->32.5V Storage Temperature ………………....…....……............ -55℃ to +105℃
Positive Logic Remote ON/OFF ( see note 3 & 4 ) Thermal Shutdown, Case Temp. .…….………….……..……. 100℃ Typ.
Input Filter …………………………………………..…………... PI Type Humidity .................................................... 95% RH max. Non condensing
OUTPUT SPECIFICATIONS: MTBF ………. MIL-STD-217F, GB, 25℃, Full Load ………… 1000khrs Typ.
Voltage Accuracy: ...........................................……….......... ±1.0% max. Dimensions ................…….. 2.28×2.40x0.50 inches (57.9x61.0×12.7 mm)
Transient Response:25% Step Load Change .…………….… <500 u sec. Case Material ................…................………….……………….. Aluminum
External Trim Adj. Range ………………..……………………….. ±10 % Weight …………………………………………………………………….. 92g
Ripple & Noise, 20MHz BW(see note 5) NOTE:
2.5 & 3.3V & 5V ……….….... 20mV RMS, max. 1. Measured From High Line to Low Line
75mV pk-pk, max. 2. Measured From Full Load to Zero Load
12V & 15V ……………..……. 30mV RMS, max. 3. Logic Compatibility …….. Open Collector ref to -Input
100mV pk-pk, max Module ON ……………………………………………. Ope n Circuit
24V ………………….……… 100mV RMS, max. Module OFF …………………………………………..…... < 0.8Vdc
240mV pk-pk, max. 4. Suffix "N" to the Model Number with Negative Logic Remote ON/OFF
Temperature Coefficient ....................……….. ................…..... ±0.03%/°C 5. Output Ripple and Noise measured with 10uF tantalum and 1uF ceramic
Short Circuit Protection .........………………........................... Continuous capacitor across output
Line Regulation (see note 1) ……....................................…. ±0.2% max. 6. Suffix “-C” to the Model Numbe r with Clear Mounting Insert (3.2mm DIA.)
Load Regulation (see note 2) ……............……….................. ±0.2% max.
Over Voltage Protection trip Range, % Vo nom. ..................... 115-140%
Current Limit ...................……………….... 110% ~150% Nominal Output
Start up time ……………………………….……… …………..…... 5 ms Typ.
6Trim
+Sense
+Vout
9
7
8
BOTTOM VIEW
M3*0.5 Through 4pl.
Function
ON/OFF
CASE
-Vin
-Vout
-Sense
+Vin
3
4
5
Pin
1
2
Mounting Inserts
Millimeters: X.X= ±0.5 , X.XX=±0.25
All Dimensions In Inches(mm)
CASE HB
Tolerances Inches: X.XX= ±0.02 , X.XXX= ±0.010
REMOTE ON/OFF CONTROL EXTERNAL OUTPUT TRIM
ON/OFF (2)
-VIN (4)
HIGH SIGNAL HERE
D ISABLE OUTPUT