47
01.19
D
Mechanical Tests
Pull test on pins:
10 N in direction of pins according to
IEC 60068-2-21
Vibration:
6 hours at 10 ... 2000 Hz and 0.75 mm
displacement amplitude or 10 g in
accordance with IEC 60068-2-6
Low air density:
1kPa = 10 mbar in accordance with
IEC 60068-2-13
Bump test:
4000 bumps at 390 m/sec2 in
accordance with IEC 60068-2-29
Packing
Available taped and reeled.
Detailed taping information and graphs
at the end of the catalogue.
For further details and graphs please
refer to Technical Information.
WIMA MKP 2
Metallized Polypropylene (PP) Capacitors in PCM 5 mm.
Capacitances from 1000 pF to 1.0 mF. Rated Voltages from 63 VDC to 1000 VDC.
Special Features Electrical Data
˜ High volume/capacitance ratio
˜ Self-healing
˜ Increased pulse duty from
250 VDC rated voltage
˜ Very low dissipation factor
˜ Negative capacitance change
versus temperature
˜ Very low dielectric absorption
˜ AEC-Q200 qualified
˜ According to RoHS 2011/65/EU
Typical Applications
For high frequency applications e.g.
˜ Sample and hold
˜ Timing
˜ Oscillating circuits
˜ High frequency coupling and
decoupling
Construction
Dielectric:
Polypropylene (PP) film
Capacitor electrodes:
Vacuum-deposited
Internal construction:
Plastic film
Vacuum-deposited
electrode
Metal contact layer
(schoopage)
Terminating wire
Encapsulation:
Solvent-resistant, flame-retardant plastic
case with epoxy resin seal, UL 94 V-0
Terminations:
Tinned wire.
Marking:
Colour: Red. Marking: Black.
Capacitance range:
1000 pF to 1.0 mF (E12-values on request)
Rated voltages:
63 VDC, 100 VDC, 250 VDC, 400 VDC,
630 VDC, 800 VDC, 1000 VDC
Capacitance tolerances:
± 20%, ±10%, ±5%
Operating temperature range:
–55+ C to +100+ C
Test specifications:
In accordance with IEC 60384-16
Climatic test category:
55/100/56 in accordance with IEC
Insulation resistance at +20+ C:
1 x 105 M¸
Measuring voltage:
Ur = 63 V: Utest = 50 V/1 min.
Ur 100 V: Utest = 100 V/1 min.
Test voltage:
1.6 Ur, 2 sec.
Maximum pulse rise time:
Capacitance max. pulse rise time V/msec
pF/mF
63 VDC 100 VDC 250 VDC 400 VDC 630 VDC 800 VDC 1000 VDC
1000 ... 2200 – – – 300 400 450 500
3300 ... 6800 – – – 300 400 450 500
0.01 ... 0.022 100 100 250 300 400 450 500
0.033 ... 0.068 100 100 250 300 400 450 –
0.1 ... 0.22 100 100 250 250 – – –
0.33 ... 0.68 100 100 250 – – – –
1.0 70 70 – – – – –
for pulses equal to the rated voltage
Dielectric absorption:
0.05 %
Dissipation factors at +20+ C: tan d
at f C0.1 mF 0.1 mF P C 1.0 mF
1 kHz 5 x 10-4 5 x 10-4
10 kHz 8 x 10-4 8 x 10-4
100 kHz 25 x 10-4 –
Voltage derating:
A voltage derating factor of 1.35 % per K
must be applied from +85+ C for DC
voltages and from +75+ C for AC
voltages
Reliability:
Operational life 300 000 hours
Failure rate P 2 fit (0.5 x Ur and 40+ C)
48
01.19
WIMA FKP 4
Continuation
General Data
D
Capacitance 63 VDC/40 VAC * 100 VDC/63 VAC *
W H L PCM** Part number W H L PCM** Part number
0.01 mF 3 7.5 7.2 5 MKP2C021001B00_ _ _ _ 3 7.5 7.2 5 MKP2D021001B00_ _ _ _
0.015 „ 3 7.5 7.2 5 MKP2C021501B00_ _ _ _ 3 7.5 7.2 5 MKP2D021501B00_ _ _ _
0.022 „ 3 7.5 7.2 5 MKP2C022201B00_ _ _ _ 3 7.5 7.2 5 MKP2D022201B00_ _ _ _
0.033 „ 3 7.5 7.2 5 MKP2C023301B00_ _ _ _ 3 7.5 7.2 5 MKP2D023301B00_ _ _ _
0.047 „ 3.5 8.5 7.2 5 MKP2C024701C00_ _ _ _ 3.5 8.5 7.2 5 MKP2D024701C00_ _ _ _
0.068 „ 4.5 9.5 7.2 5 MKP2C026801E00_ _ _ _ 4.5 9.5 7.2 5 MKP2D026801E00_ _ _ _
0.1 mF 5 10 7.2 5 MKP2C031001F00_ _ _ _ 5 10 7.2 5 MKP2D031001F00_ _ _ _
0.15 „ 5.5 11.5 7.2 5 MKP2C031501H00_ _ _ _ 5.5 11.5 7.2 5 MKP2D031501H00_ _ _ _
0.22 „ 7.2 13 7.2 5 MKP2C032201K00_ _ _ _ 7.2 13 7.2 5 MKP2D032201K00_ _ _ _
0.33 „ 8.5 14 7.2 5 MKP2C033301M00_ _ _ _ 8.5 14 7.2 5 MKP2D033301M00_ _ _ _
0.47 „ 8.5 14 7.2 5 MKP2C034701M00_ _ _ _ 8.5 14 7.2 5 MKP2D034701M00_ _ _ _
0.68 „ 8.5 14 7.2 5 MKP2C036801M00_ _ _ _ 8.5 14 7.2 5 MKP2D036801M00_ _ _ _
1.0 mF 11 16 7.2 5 MKP2C041001N00_ _ _ _ 11 16 7.2 5 MKP2D041001N00_ _ _ _
Capacitance 250 VDC/160 VAC* 400 VDC/200 VAC *
W H L PCM** Part number W H L PCM** Part number
1000 pF 3 7.5 7.2 5 MKP2G011001B00_ _ _ _
1500 „ 3 7.5 7.2 5 MKP2G011501B00_ _ _ _
2200 „ 3 7.5 7.2 5 MKP2G012201B00_ _ _ _
3300 „ 3 7.5 7.2 5 MKP2G013301B00_ _ _ _
4700 „ 3 7.5 7.2 5 MKP2G014701B00_ _ _ _
6800 „ 3 7.5 7.2 5 MKP2G016801B00_ _ _ _
0.01 mF 3 7.5 7.2 5 MKP2F021001B00_ _ _ _ 3.5 8.5 7.2 5 MKP2G021001C00_ _ _ _
0.015 „ 3 7.5 7.2 5 MKP2F021501B00_ _ _ _ 3.5 8.5 7.2 5 MKP2G021501C00_ _ _ _
0.022 „ 3 7.5 7.2 5 MKP2F022201B00_ _ _ _ 4.5 9.5 7.2 5 MKP2G022201E00_ _ _ _
0.033 „ 3 7.5 7.2 5 MKP2F023301B00_ _ _ _ 5.5 11.5 7.2 5 MKP2G023301H00_ _ _ _
0.047 „ 3.5 8.5 7.2 5 MKP2F024701C00_ _ _ _ 7.2 13 7.2 5 MKP2G024701K00_ _ _ _
0.068 „ 4.5 9.5 7.2 5 MKP2F026801E00_ _ _ _ 7.2 13 7.2 5 MKP2G026801K00_ _ _ _
0.1 mF 5 10 7.2 5 MKP2F031001F00_ _ _ _ 8.5 14 7.2 5 MKP2G031001M00_ _ _ _
0.15 „ 7.2 13 7.2 5 MKP2F031501K00_ _ _ _ 11 16 7.2 5 MKP2G031501N00_ _ _ _
0.22 „ 7.2 13 7.2 5 MKP2F032201K00_ _ _ _
0.33 „ 8.5 14 7.2 5 MKP2F033301M00_ _ _ _
0.47 „ 11 16 7.2 5 MKP2F034701N00_ _ _ _
Capacitance 630 VDC/250 VAC* ** PCM = Printed circuit module = pin spacing.
W H L PCM** Part number Dims. in mm.
1000 pF 3 7.5 7.2 5 MKP2J011001B00_ _ _ _
1500 „ 3 7.5 7.2 5 MKP2J011501B00_ _ _ _
2200 „ 3 7.5 7.2 5 MKP2J012201B00_ _ _ _
3300 „ 3 7.5 7.2 5 MKP2J013301B00_ _ _ _
4700 „ 3 7.5 7.2 5 MKP2J014701B00_ _ _ _
6800 „ 3.5 8.5 7.2 5 MKP2J016801C00_ _ _ _
0.01 mF 4.5 9.5 7.2 5 MKP2J021001E00_ _ _ _
0.015 „ 5 10 7.2 5 MKP2J021501F00_ _ _ _
0.022 „ 5.5 11.5 7.2 5 MKP2J022201H00_ _ _ _
0.033 „ 7.2 13 7.2 5 MKP2J023301K00_ _ _ _
0.047 „ 8.5 14 7.2 5 MKP2J024701M00_ _ _ _
0.068 „ 11 16 7.2 5 MKP2J026801N00_ _ _ _
* AC voltage: f 400 Hz; 1.4 x Urms + UDC Ur
Rights reserved to amend design data without prior notification.
Continuation page 49
WIMA MKP 2
5
PCM
at the pin exit
points
(0.5)±
L
W
H
d
6-2
d = 0.5 l
Part number completion:
Tolerance: 20 % = M
10 % = K
5 % = J
Packing: bulk = S
Pin length: 6-2 = SD
Taped version see page 149.
49
01.19
Continuation
General Data
D
Capacitance 800 VDC/250 VAC* 1000 VDC/250 VAC *
W H L PCM** Part number W H L PCM** Part number
1000 pF 3 7.5 7.2 5 MKP2L011001B00_ _ _ _ 3 7.5 7.2 5 MKP2O111001B00_ _ _ _
1500 „ 3 7.5 7.2 5 MKP2L011501B00_ _ _ _ 3 7.5 7.2 5 MKP2O111501B00_ _ _ _
2200 „ 3 7.5 7.2 5 MKP2L012201B00_ _ _ _ 3 7.5 7.2 5 MKP2O112201B00_ _ _ _
3300 „ 3 7.5 7.2 5 MKP2L013301B00_ _ _ _ 3.5 8.5 7.2 5 MKP2O113301C00_ _ _ _
4700 „ 3.5 8.5 7.2 5 MKP2L014701C00_ _ _ _ 4.5 9.5 7.2 5 MKP2O114701E00_ _ _ _
6800 „ 4.5 9.5 7.2 5 MKP2L016801E00_ _ _ _ 5 10 7.2 5 MKP2O116801F00_ _ _ _
0.01 mF 5 10 7.2 5 MKP2L021001F00_ _ _ _ 7.2 13 7.2 5 MKP2O121001K00_ _ _ _
0.015 „ 5.5 11.5 7.2 5 MKP2L021501H00_ _ _ _ 8.5 14 7.2 5 MKP2O121501M00_ _ _ _
0.022 „ 7.2 13 7.2 5 MKP2L022201K00_ _ _ _ 11 16 7.2 5 MKP2O122201N00_ _ _ _
0.033 „ 8.5 14 7.2 5 MKP2L023301M00_ _ _ _
0.047 „ 11 16 7.2 5 MKP2L024701N00_ _ _ _
* AC voltage: f 400 Hz; 1.4 x Urms + UDC Ur
** PCM = printed circuit module = pin spacing.
Dims. in mm.
Rights reserved to amend design data without prior notification.
5
PCM
at the pin exit
points
(0.5)±
L
W
H
d
6-2
400 VDC
f
Hz
10 2510 2510 2510
3
456
5
10
5
2
10
200
2
U
V
rms
0.022 µF
0.01 µF
4700 pF
2200 pF
1000 pF
0.047 µF
0.068 µF
630 VDC
f
Hz
10 2510 2510 2510
34
56
5
2
10
5
2
10
250
2
U
V
rms
0.01 µF
0.022 µF
0.047 µF
1000 pF
2200 pF
4700 pF
Permissible AC voltage in relation to frequency at 10) C internal temperature rise (general guide).
1000 VDC
f
Hz
10 2510 2510 2510
34
56
5
2
10
5
2
10
250
2
U
V
rms
0.01 µF
1000 pF
2200 pF
4700 pF
Part number completion:
Tolerance: 20 % = M
10 % = K
5 % = J
Packing: bulk = S
Pin length: 6-2 = SD
Taped version see page 149.
WIMA MKP 2
110 100
1000
f/MHz
357357
7
5
3
7
5
3
10
1
0.1
0.01
Z
-- 1000 pF
-- 2200 pF
-- 4700 pF
-- 0.01 µF
-- 0.022 µF
-- 0.047 µF
-- 0.1 µF
-- 0.33 µF
Impedance change with frequency
(general guide).
d = 0.5 l
01.19
15
D
Recommendation for Processing
and Application of
Through-Hole Capacitors
WIMA Quality and Environmental Philosophy
ISO 9001:2015 Certification
ISO 9001:2015 is an international basic
standard of quality assurance systems
for all branches of industry. The approval
according to ISO 9001:2015 of our facto-
ries by the infaz (Institut für Auditierung und
Zertifizierung) certifies that organisation,
equipment and monitoring of quality assu-
rance in our factories correspond to inter-
nationally recognized standards.
WIMA WPCS
The WIMA Process Control System (WPCS)
is a quality surveillance and optimization
system developed by WIMA. WPCS is a
major part of the quality-oriented WIMA
production. Points of application during
production process:
” incoming material inspection
” metallization
” film inspection
” schoopage
” pre-healing
” pin attachment
” cast resin preparation/
encapsulation
” 100% final inspection
” Testing as per customer requirements
WIMA Environmental Policy
All WIMA capacitors, irrespective of
whether through-hole devices or SMD,
are made of environmentally friendly
materials. Neither during manufacture
nor in the product itself any toxic sub-
stances are used, e.g.
– Lead – PBB/PBDE
– PCB – Arsenic
– CFC – Cadmium
– Hydrocarbon chloride – Mercury
– Chromium 6+ – etc.
We merely use pure, recyclable materials
for packing our components, such as:
” carton
” cardboard
” adhesive tape made of paper
” polystyrene
We almost completely refrain from using
packing materials such as:
” adhesive tapes made of plastic
” metal clips
RoHS Compliance
According to the RoHS Directive 2011/65/EU
as amended from time to time certain hazar-
dous substances like e.g. lead, cadmium,
mercury must not be used any longer in
electronic equipment as of July 1st, 2006. For
the sake of the environment WIMA has re-
fraind from using such substances since years
already.
WIMA capacitors are lead free
in accordance with Ro
HS 2011/65/EU
WIMA Kondensatoren sind bleifrei
konform RoHS 2011/65/EU
Tape for lead-free WIMA capacitors
DIN EN ISO 14001:2004
WIMA’s environmental management has
been established in accordance with the
guidelines of DIN EN ISO 14001:2004 to
optimize the production processes with
regard to energy and resources.
Soldering Process
Internal temperature of the capacitor must
be kept as follows:
Polyester: preheating: Tmax. T 125° C
soldering: Tmax. T 135° C
Polypropylene: preheating: Tmax. T 100° C
soldering: Tmax. T 110° C
Single wave soldering
Soldering bath temperature: T P 260 ° C
Dwell time: t P 5 sec
Double wave soldering
Soldering bath temperature: T P 260 ° C
Dwell time: St P 5 sec
Due to different soldering processes and
heat requirements the graphs are to be
regarded as a recommendation only.
149
01.19
D
P
P1
P0
P2
F
d
P
P1
H1
H
P0
d
P2
F
t
D0
W2
Vh
W0
P1
P2
P0
P
H1
H
W
1
W
d
F
Diagram 1:
PCM2.5/5/7.5mm
Diagram3:PCM 22.5and 27.5*mm
*PCM 27.5taping possiblewithtwo feed holesbetween components
Di
agram 2: PCM10/15mm
Dimensions for Radial Taping
Designation Symbol PCM 2.5 taping PCM 5 taping PCM 7.5 taping PCM 10 taping* PCM 15 taping* PCM 22.5 taping PCM 27.5 taping
Carrier tape width W 18.0
p0.5
18.0
p0.5
18.0
p0.5
18.0
p0.5
18.0
p0.5
18.0
p0.5
18.0
p0.5
Hold-down tape width W
0
6.0 for hot-sealing 6.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing
adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape
Hole position W
1
9.0
p0.5
9.0
p0.5
9.0
p0.5
9.0
p0.5
9.0
p0.5
9.0
p0.5
9.0
p0.5
Hold-down tape position W
2
0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max.
Feed hole diameter D
0
4.0
p0.2
4.0
p0.2
4.0
p0.2
4.0
p0.2
4.0
p0.2
4.0
p0.2
4.0
p0.2
Pitch of component P 12.7
p1.0
12.7
p1.0
12.7
p1.0
25.4
p1.0
25.4
p1.0
38.1
p1.5
3
*8.1
p1.5
or 50.8
p1.5
cumulative pitch
cumulative pitch
cumulative pitch
cumulative pitch
cumulative pitch
cumulative pitch
cumulative pitch
Feed hole pitch P
0
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
Feed hole centre P
1
5.1
p0.5
3.85
p0.7
2.6
p0.7
7.7
p0.7
5.2
p0.7
7.8
p0.7
5.3
p0.7
to pin
Hole centre to P
2
6.35
p1.3
6.35
p1.3
6.35
p1.3
12.7
p1.3
12.7
p1.3
19.05
p1.3
19.05
p1.3
component centre
Feed hole centre to bottom H 16.5
p0.3
16.5
p0.3
16.5
p0.5
16.5
p0.5
16.5
p0.5
16.5
p0.5
16.5
p0.5
edge of the component 18.5
p0.5
18.5
p0.5
18.5
p0.5
18.5
p0.5
18.5
p0.5
18.5
p0.5
18.5
p0.5
Feed hole centre to top H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
edge of the component 32.25 max. 32.25 max. 24.5 to 31.5 25.0 to 31.5 26.0 to 37.0 30.0 to 43.0 35.0 to 45.0
Pin spacing at F 2.5
p0.5
5.0
+0.8
7.5
p0.8
10.0
p0.8
15
p0.8
22.5
p0.8
27.5
p0.8
upper edge of carrier tape
–0.2
Pin diameter d 0.4
p0.05
0.5
p0.05
„
0.5
p0.05
or
0.6
–0.05
„
0.5
p0.05
or
0.6
–0.05
0.8
–0.05
0.8
–0.05
0.8
–0.05
Component alignment Dh p 2.0 max. p 2.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max.
Total tape thickness t 0.6
p0.2
0.6
p0.2
0.6
p0.2
0.6
p0.2
0.6
p0.2
0.6
p0.2
0.6
p0.2
ROLL/AMMO AMMO
Package
(see also page 150)
Unit see details page 151.
Dims in mm.
„ Diameter of pins see General Data. Please clarify customer-specific deviations with the manufacturer.
* PCM 10 and PCM 15 can be crimped to PCM 7.5.
Position of components according to PCM 7.5 (sketch 1). P0 = 12.7 or 15.0 is possible
REEL
P 360 max.
B
52 p2 depending on
P 30 p1 58 p2 comp. dimensions
52 p2 54 p2 depending
REEL
P 360 max. B 58 p2
or
REEL
P 500 max. B 60 p2 on PCM and
P 30 p1 66 p2 P 25 p1 68 p2 component dimensions
+0.06 +0,06 +0,08 +0,08 +0.08
Typical Dimensions for
Taping Configuration
150
01.19
D
˜ ROLL Packaging ˜ AMMO Packaging ˜ REEL Packaging
Labelling of package units in
plain text and with
alphanumerical Bar Code
Scanner decoding of
„ WIMA supplier number
„ Customer‘s P/O number
„ Customer‘s part number
„ WIMA confirmation number
„ WIMA part number
„ Lot number
„ Date code
„ Quantity
In addition part description of
– article
– capacitance value
– rated voltage
– dimensions
– capacitance tolerance
– packing
as well as gross weight and customer‘s
name are indicated in plain text.
BARCODE „Code 39”
BAR CODE (Labelling)
50 max.
70 max.
340 max.
490 max.
340 max.
370 max.
30 1±
25 1±
360 max.
500 max.
B
340 max.
340 max.
50 max.
Types of Tape Packaging of
Capacitors for Automatic
Radial Insertion
151
01.19
D
Packing Quantities for Capacitors with
Radial Pins in PCM 2.5 mm to 22.5 mm
* TPS (Tray-Packing-System). Plate versions may have different packing units. Moulded versions. Rights reserved to amend design data without prior notification.
Samples and pre-production needs on request.
PCM Size
pcs. per packing unit
bulk
ROLL REEL AMMO
P 360 P 500 340 x 340 490 x 370
H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5
W H L Codes S N O F I H J A C B D
2.5 mm
2.5 7 4.6 0B 5000 2200 2500 –2800 –
3 7.5 4.6 0C 5000 2000 2300 –2300 –
3.8 8.5 4.6 0D 5000 1500 1800 –1800 –
4.6 9 4.6 0E 5000 1200 1500 –1500 –
5.5 10 4.6 0F 5000 900 1200 –1200 –
5 mm
2.5 6.5 7.2 1A 5000 2200 2500 –2800 –
3 7.5 7.2 1B 5000 2000 2300 –2300 –
3.5 8.5 7.2 1C 5000 1600 2000 –2000 –
4.5 6 7.2 1D 6000 1300 1500 –1500 –
4.5 9.5 7.2 1E 4000 1300 1500 –1500 –
5 10 7.2 1F 3500 1100 1400 –1400 –
5.5 7 7.2 1G 4000 1000 1200 –1200 –
5.5 11.5 7.2 1H 2500 1000 1200 –1200 –
6.5 8 7.2 1I 2500 800 1000 –1000 –
7.2 8.5 7.2 1J 2500 700 1000 –1000 –
7.2 13 7.2 1K 2000 700 950 –1000 –
8.5 10 7.2 1L 2000 600 800 – 800 –
8.5 14 7.2 1M 1500 600 800 – 800 –
11 16 7.2 1N 1000 500 600 – 640 –
7.5 mm
2.5 7 10 2A 5000 –2500 4400 2500 –
3 8.5 10 2B 5000 –2200 4300 2300 4150
4 9 10 2C 4000 –1700 3200 1700 3100
4.5 9.5 10.3 2D 3500 –1500 2900 1400 2700
5 10.5 10.3 2E 3000 –1300 2500 1300 –
5.7 12.5 10.3 2F 2000 –1000 2200 1100 –
7.2 12.5 10.3 2G 1500 – 900 1800 1000 –
10 mm
3 9 13 3A 3000 –1100 2200 –1900
4 8.5 13.5 FA 3000 – 900 1600 –1450
4 9 13 3C 3000 – 900 1600 –1450
4 9.5 13 3D 3000 – 900 1600 –1400
5 10 13.5 FB 2000 – 700 1300 –1200
5 11 13 3F 3000 – 700 1300 –1200
6 12 13 3G 2400 – 550 1100 –1000
6 12.5 13 3H 2400 – 550 1100 –1000
8 12 13 3I 2000 – 400 800 – 740
15 mm
5 11 18 4B 2400 – 600 1200 –1150
5 13 19 FC 1000 – 600 1200 –1200
6 12.5 18 4C 2000 – 500 1000 –1000
6 14 19 FD 1000 – 500 1000 –1000
7 14 18 4D 1600 – 450 900 – 850
7 15 19 FE 1000 – 450 900 – 850
8 15 18 4F 1200 – 400 800 – 740
8 17 19 FF 500 – 400 800 – 740
9 14 18 4H 1200 – 350 700 – 650
9 16 18 4J 900 – 350 700 – 650
10 18 19 FG 500 – 300 650 – 590
11 14 18 4M 1000 – 300 600 – 540
22.5 mm
5 14 26.5 5A 1200 – – 800 – 770
6 15 26.5 5B 1000 – – 700 – 640
7 16.5 26.5 5D 760 – – 600 – 550
8 20 28 FH 500 – – 500 – 480
8.5 18.5 26.5 5F 500 – – 480 – 450
10 22 28 FI 570*– – 420 – 380
10.5 19 26.5 5G 594*– – 400 – 360
10.5 20.5 26.5 5H 594*– – 400 – 360
11 21 26.5 5I 561*– – 380 – 350
12 24 28 FJ 480*– – 350 – 310
152
01.19
D
* for 2-inch transport pitches. Moulded versions. Rights reserved to amend design data without prior notification.
* TPS (Tray-Packing-System). Plate versions may have different packing units.
Samples and pre-production needs on request.
Updated data on www.wima.com
Packing Quantities for Capacitors with
Radial Pins in PCM 27.5 mm to 52.5 mm
PCM Size
pcs. per packing unit
bulk
ROLL REEL AMMO
P 360 P 500 340 x 340 490 x 370
H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5
W H L Codes S N O F I H J A C B D
27.5 mm
9 19 31.5 6A 567*– – 460/340* – 420
11 21 31.5 6B 459*– – 380/280* – 350
13 24 31.5 6D 378*– – 300 – 290
13 25 33 FK 405*–––––
15 26 31.5 6F 324*– – 270 – 250
15 26 33 FL 324*–––––
17 29 31.5 6G 198*–––––
17 34.5 31.5 6I 198*–––––
20 32 33 FM 162*–––––
20 39.5 31.5 6J 162*–––––
37.5 mm
9 19 41.5 7A 441*–––––
11 22 41.5 7B 357*–––––
13 24 41.5 7C 294*–––––
15 26 41.5 7D 252*–––––
17 29 41.5 7E 154*–––––
19 32 41.5 7F 140*–––––
20 39.5 41.5 7G 126*–––––
24 45.5 41.5 7H 112*–––––
31 46 41.5 7I 84*–––––
35 50 41.5 7J 35*–––––
40 55 41.5 7K 28*–––––
48.5 mm
19 31 56 8D 120*–––––
23 34 56 8E 80*–––––
27 37.5 56 8H 84*–––––
33 48 56 8J 25*–––––
37 54 56 8L 25*–––––
52.5 mm
25 45 57 9D 70*–––––
30 45 57 9E 60*
35 50 57 9F 25*
45 55 57 9H 20*–––––
45 65 57 9J 20*–––––
147
01.19
D
A WIMA part number consists of 18 digits and is composed as follows:
Field 1 - 4: Type description
Field 5 - 6: Rated voltage
Field 7 - 10: Capacitance
Field 11 - 12: Size and PCM
Field 13 - 14: Version code (e.g. Snubber versions)
Field 15: Capacitance tolerance
Field 16: Packing
Field 17 - 18: Pin length (untaped)
12345678910 11 12 13 14 15 16 17 18
M K S 2 C 0 2 1 0 0 1 A 0 0 M S S D
MKS 2 63 VDC 0.01 mF2.5 x 6.5 x 7.2 -20 %bulk 6 -2
WIMA Part Number System
The data on this page is not complete and serves only to explain the part number system. Part number information is listed on the
pages of the respective WIMA range.
Type description: Rated voltage: Capacitance: Size: Tolerance:
SMD-PET = SMDT 50 VDC = B0 22 pF = 0022 4.8 x 3.3 x 3 Size 1812 = KA ±20 % = M
SMD-PEN = SMDN 63 VDC = C0 47 pF = 0047 4.8 x 3.3 x 4 Size 1812 = KB ±10 % = K
SMD-PPS = SMDI 100 VDC = D0 100 pF = 0100 5.7 x 5.1 x 3.5 Size 2220 = QA ±5 % = J
FKP 02 = FKP0 250 VDC = F0 150 pF = 0150 5.7 x 5.1 x 4.5 Size 2220 = QB ±2.5 % = H
MKS 02 = MKS0 400 VDC = G0 220 pF = 0220 7.2 x 6.1 x 3 Size 2824 = TA ±1 % = E
FKS 2 = FKS2 450 VDC = H0 330 pF = 0330 7.2 x 6.1 x 5 Size 2824 = TB ...
FKP 2 = FKP2 520 VDC = H2 470 pF = 0470 10.2 x 7.6 x 5 Size 4030 = VA
FKS 3 = FKS3 600 VDC = I0 680 pF = 0680 12.7 x 10.2 x 6 Size 5040 = XA
FKP 3 = FKP 3 630 VDC = J0 1000 pF = 1100 15.3 x 13.7 x 7 Size 6054 = YA Packing:
MKS 2 = MKS2 700 VDC = K0 1500 pF = 1150 2.5 x 7 x 4.6 PCM 2.5 = 0B AMMO H16.5 340 x 340 = A
MKP 2 = MKP2 800 VDC = L0 2200 pF = 1220 3 x 7.5 x 4.6 PCM 2.5 = 0C AMMO H16.5 490 x 370 = B
MKS 4 = MKS4 850 VDC = M0 3300 pF = 1330 2.5 x 6.5 x 7.2 PCM 5 = 1A AMMO H18.5 340 x 340 = C
MKP 4C = MKPC 900 VDC = N0 4700 pF = 1470 3 x 7.5 x 7.2 PCM 5 = 1B AMMO H18.5 490 x 370 = D
MKP 4 = MKP4 1000 VDC = O1 6800 pF = 1680 2.5 x 7 x 10 PCM 7.5 = 2A REEL H16.5 360 = F
MKP 10 = MKP1 1100 VDC = P0 0.01 mF= 2100 3 x 8.5 x 10 PCM 7.5 = 2B REEL H16.5 500 = H
FKP 1 = FKP1 1200 VDC = Q0 0.022 mF= 2220 3 x 9 x 13 PCM 10 = 3A REEL H18.5 360 = I
MKP-X2 = MKX2 1250 VDC = R0 0.047 mF= 2470 4 x 9 x 13 PCM 10 = 3C REEL H18.5 500 = J
MKP-X1 R = MKX1 1500 VDC = S0 0.1 mF= 3100 5 x 11 x 18 PCM 15 = 4B ROLL H16.5 = N
MKP-Y2 = MKY2 1600 VDC = T0 0.22 mF= 3220 6 x 12.5 x 18 PCM 15 = 4C ROLL H18.5 = O
MP 3-X2 = MPX2 2000 VDC = U0 0.47 mF= 3470 5 x 14 x 26.5 PCM 22.5 = 5A BLISTER W12 180 = P
MP 3-X1 = MPX1 2500 VDC = V0 1 mF= 4100 6 x 15 x 26.5 PCM 22.5 = 5B BLISTER W12 330 = Q
MP 3-Y2 = MPY2 3000 VDC = W0 2.2 mF= 4220 9 x 19 x 31.5 PCM 27.5 = 6A BLISTER W16 330 = R
MP 3R-Y2 = MPRY 4000 VDC = X0 4.7 mF= 4470 11 x21 x 31.5 PCM 27.5 = 6B BLISTER W24 330 = T
MKP 4F = MKPF 6000 VDC = Y0 10 mF= 5100 9 x 19 x 41.5 PCM 37.5 = 7A Bulk/TPS Standard = S
Snubber MKP = SNMP 250 VAC = 0W 22 mF= 5220 11 x 22 x 41.5 PCM 37.5 = 7B ...
Snubber FKP = SNFP 275 VAC = 1W 47 mF= 5470 19 x 31 x 56 PCM 48.5 = 8D
GTO MKP = GTOM 300 VAC = 2W 100 mF= 6100 25 x 45 x 57 PCM 52.5 = 9D
DC-LINK MKP 3 = DCP3 305 VAC = AW 220 mF= 6220 ...
DC-LINK MKP 4 = DCP4 350 VAC = BW 1000 mF= 7100
DC-LINK MKP 4S = DCPS 440 VAC = 4W 1500 mF= 7150
DC-LINK MKP 5 = DCP5 500 VAC = 5W ... Version code: Pin length (untaped)
DC-LINK MKP 6 = DCP6 ... Standard = 00 3.5 ±0.5 = C9
DC-LINK HC = DCHC Version A1 = 1A 6 -2 = SD
DC-LINK HY = DCHY Version A1.1.1 = 1B 16 ±1 = P1
Version A2 = 2A ...
... Pin length (taped)
none = 00
