PPB01CM23N - Carlo Gavazzi Group

Specifications are subject to change without notice (16.10.06) 1

Monitoring Relays

Product Description Ordering Key

Housing

Function

Type

Item number

Output

Power supply

• TRMS 3-phase over and under voltage,

phase sequence and phase loss monitoring relays

• Detect when all 3 phases are present and have the

correct phase sequence (except for N versions)

•Available versions (W4) supplied between phase and

neutral

• Detect if all the 3-phase-phase or phase-neutral volt-

ages are within the set limits

• Upper and lower limits separately adjustable

• Measure on own power supply

• Selection of measuring range by DIP-switches

• Adjustable voltage on relative scale

• Adjustable delay function (0.1 to 30 s)

• Output: 8 A SPDT relay N.E.

•For mounting on DIN-rail in accordance with

DIN/EN 50 022 (DPB01) or plug-in module (PPB01)

• 22.5 mm Euronorm housing (DPB01)

or 36 mm plug-in module (PPB01)

• LED indication for relay, alarm and power supply ON

Type Selection

Mounting Phase sequence Output Supply: Supply: Supply:

detection 208 to 240 VAC 380 to 415 VAC 380 to 480 VAC

DIN-rail yes SPDT DPB 01 C M23 DPB 01 C M48 W4 DPB 01 C M48

Plug-in yes SPDT PPB 01 C M23 PPB 01 C M48 W4

Plug-in yes SPDT PPB 01 C M48

DIN-rail no SPDT DPB 01 C M23 N DPB 01 C M48 N W4 DPB 01 C M48 N

Plug-in no SPDT PPB 01 C M23 N PPB 01 C M48 N W4

Plug-in no SPDT PPB 01 C M48 N

Input

L1, L2, L3, N DPB01: Terminals L1, L2, L3, N

PPB01: Terminals 5, 6, 7, 11

Measure on own supply

Note: Connect the neutral only

if it is intrinsically at the star

centre

Measuring ranges

208 to 240 VAC 177 to 275 VL-L AC

M23 versions

380 to 415 VAC 323 to 475 VL-L AC

PPB01CM48

PPB01CM48N

D/P PB01CM48W4

D/P PB01CM48NW4

380 to 480 VAC 323 to 550 VL-L AC

DPB01CM48

DPB01CM48N

True RMS 3-Phase, 3-Phase+N, Multi-function

Types DPB01, PPB01

Input Specifications

DPB 01 C M23

3-phase or 3-phase+neutral

line voltage monitoring relay

for phase sequence, phase

loss, over and under voltage

(separately adjustable set

points) with built-in time

delay function.

Supply ranges from 208 to

480 VAC covered by two

multivoltage relays.

DPB01 PPB01

Ranges

Upper level +2 to +22%

of the nominal voltage

Lower level -22 to -2%

of the nominal voltage

Note: The input voltage

must not exceed the maximum

rated voltage or drop below

the minumum rated voltage

reported above.

Hysteresis

Set points from 2 to 5% 1%

Set points from 5 to 22% 2%

2Specifications are subject to change without notice (16.10.06)

DPB01, PPB01

Mode of Operation

Connected to the 3 phases

(and neutral) DPB01 and

PPB01 operate when all 3

phases arepresent at the

same time, the phase

sequence is correct (not N

versions) and the phase-

phase (or phase-neutral)

voltage levels are within set

limits.

If one or morephase-phase

or phase-neutral voltages

exceeds the upper set level

or drops below the lower set

level, the red LED starts

flashing 2 Hz and the output

relay releases after the set

time period. In any case if

phase-neutral measurement

is selected both phase-

phase and phase-neutral

voltages are monitored. If

the phase sequence is

wrong or one phase is lost,

the output relay releases

immediately.

Only 200 ms delay occurs.

The failureis indicated by

the red LED flashing 5 Hz

during the alarmcondition.

Example 1

(mains network monitoring)

The relay monitors over and

under voltage, phase loss

and correct phase

sequence.

In case of N versions, the

relay monitors over and

under voltage.

Example 2

(load monitoring)

The relay releases in case of

interruption of one or more

phases, when one or more

voltages drop below the

lower set level or exceed the

upper set level.

Power supply Overvoltage cat. III

Rated operational voltage (IEC 60664, IEC 60038)

through terminals:

L1, L2, L3, N (DPB01)

5, 6, 7, 11 (PPB01)

D/P PB01CM23, 208 to 240 VL-L AC ±15%

D/P PB01CM23N 45 to 65 Hz

D/P PB01CM48W4, 380 to 415 VL-L AC ±15%

D/P PB01CM48NW4, (220 to 240 VL-N AC ±15%)

PPB01CM48, PPB01CM48N 45 to 65 Hz

DPB01CM48, DPB01CM48N 380 to 480 VL-L AC ±15%

(220 to 277 VL-N AC ±15%)

45 to 65 Hz

Rated operational power

DPB01CM23x, PPB01CM23x 13 VA @ 230 ∆VAC, 50 Hz

DPB01CM48x, PPB01CM48x 13 VA@400 ∆VAC, 50 Hz

Supplied by L1 and L2

DPB01CM48xW4

DPB01CM48xW4 13 VA@400 ∆VAC, 50 Hz

Supplied by L1 and N

Supply Specifications

Power ON delay 1 s ± 0.5 s or 6 s ± 0.5 s

Reaction time

Incorrect phase sequence or

total phase loss < 200 ms

Voltage level (input signal variation from

-20% to +20% or from

+20% to -20% of set value)

Alarm ON delay < 200 ms (delay < 0.1 s)

Alarm OFF delay < 200 ms (delay < 0.1 s)

Accuracy (15 min warm-up time)

Temperature drift ± 1000 ppm/°C

Delay ON alarm ± 10% on set value ± 50 ms

Repeatability ± 0.5% on full-scale

Indication for

Power supply ON LED, green

Alarm ON LED, red (flashing 2 Hz

during delay time)

Output relay ON LED, yellow

Environment

Degree of protection IP 20

Pollution degree 3 (DPB01), 2 (PPB01)

Operating temperature

@Max. voltage, 50 Hz -20 to 60°C, R.H. < 95%

@Max. voltage, 60 Hz -20 to 50°C, R.H. < 95%

Storage temperature -30 to 80°C, R.H. < 95%

Housing

Dimensions DPB01 22.5 x 80 x 99.5 mm

PPB01 36 x 80 x 94 mm

Weight Approx. 120 g

Screw terminals

Tightening torque Max. 0.5 Nm

according to IEC 60947

Approvals UL, CSA

(except for W4 versions)

CE Marking Y

EMC Electromagnetic Compatibility

Immunity According to EN 61000-6-2

Emissions According to EN 61000-6-3

General Specifications

Output SPDT relay

Rated insulation voltage 250 VAC

Contact ratings (AgSnO2)µ

Resistive loads AC 1 8 A @ 250 VAC

DC12 5 A @ 24 VDC

Small inductive loads AC 15 2.5 A @ 250 VAC

DC 13 2.5 A @ 24 VDC

Mechanical life ≥30x106operations

Electrical life ≥105operations

(at 8 A, 250 V, cos ϕ=1)

Operating frequency ≤7200 operations/h

Dielectric strength

Dielectric voltage 2 kVAC (rms)

Rated impulse withstand volt. 4 kV (1.2/50 µs)

Output Specifications

Specifications are subject to change without notice (16.10.06) 3

DPB01, PPB01

Adjust the input range set-

ting the DIP switches 3 and

4 as shown below.

Select the desired function

setting the DIP switches 1

and 2 as shown below.

To access the DIP swiches

open the grey plastic cover

as shown below

Selection of level and time

delay:

Upper knob:

Setting of lower level on rel-

ative scale.

Centre knob:

Setting of upper level on rel-

ative scale.

Lower knob:

Setting of delay on alarm

time on absolute scale (0.1

to30 s).

Function/Range/Level and Time Delay Setting

Power ON delay

ON: 6 s ± 0.5 s

OFF: 1 s ± 0.5 s

Monitored voltage

ON: Phase-Neutral

OFF: Phase-Phase

Measuring range

SW3 ON ON OFF OFF

SW4 ON OFF ON OFF

M23 Ph-Ph 208 VAC 220 VAC 230 VAC 240 VAC

Voltage

M48 Ph-Ph 380 VAC 400 VAC 415 VAC 480 VAC

Voltage DPB01CM48,

DPB01CM48N

only

M48 Ph-N 220 VAC 230 VAC 240 VAC 277 VAC

Voltage DPB01CM48,

DPB01CM48N

only

Operation Diagrams

4Specifications are subject to change without notice (16.10.06)

Operation Diagrams (cont.)

(*) Nversions don’t detect incorrect phase sequence.

DPB01, PPB01

(*)

Wiring Diagrams

DPB01 PPB01

Specifications are subject to change without notice (16.10.06) 5

Dimensions

22.5

83.5

99.5

28.5

DIN-rail

Note

When DPB01 or PPB01 is used with phase indicator lamps (see examples in the following diagrams), the lamp H1 or H2

might be dimly lit when there is a phase loss in L1 or L2. This might happen if the lamps used are the typical low power indi-

cator lamps, and there are no other loads present.

This fact can be avoided by using W4 models. Note that the neutral must be always connected to the device.

L2 L3L1

m<3

16 18

UH1H2H3

DPB01

m<3

H1H2H3

PPB01

28.5

Plug-in

DPB01, PPB01