Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC687LP4 / 687LP4E v04.0509 Mixers - SINGLE & DOUBLE BALANCED - SMT 10 BiCMOS MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 1.7 - 2.2 GHz Typical Applications Features The HMC687LP4(E) is Ideal for: High Input IP3: +35 dBm * Cellular/3G & LTE/WiMAX/4G 8 dB Conversion Loss @ 0 dBm LO * Basestations & Repeaters Optimized for High Side LO Input * GSM, CDMA & OFDM Upconversion & Downconversion Applications * Transmitters and Receivers Adjustable Supply Current 24 Lead 4x4mm SMT Package: 16mm2 Functional Diagram General Description The HMC687LP4(E) is a high dynamic range passive MMIC mixer with integrated LO amplifier in a 4x4 SMT QFN package covering 1.7 to 2.2 GHz. Excellent input IP3 performance of +35 dBm for down conversion is provided for 3G & 4G GSM/CDMA applications at an LO drive of 0 dBm. With an input 1 dB compression of +23 dBm, the RF port will accept a wide range of input signal levels. Conversion loss is 8 dB typical. The DC to 500 MHz IF frequency response will satisfy GSM/CDMA transmit or receive frequency plans. The HMC687LP4(E) is optimized for high side LO frequency plans and is pin for pin compatible with the HMC685LP4(E) which is a 1.7 - 2.2 GHz converter optimized for low side LO. Electrical Specifications, TA = +25 C, IF = 200 MHz, LO = 0 dBm, Vcc = Vcc1, 2, 3 = +5V, G_Bias = +2.5V* Icc = 120 mA Nominal Supply Parameter Min. Typ. Icc = 100 mA Icc = 70 mA Typ. Typ. Max. Units Frequency Range, RF 1.7 - 2.2 GHz Frequency Range, LO 1.7 - 2.4 GHz Frequency Range, IF DC - 500 Conversion Loss 8 Noise Figure (SSB) 10.5 MHz 8 8 dB 8 8 8 dB 34 dB LO to RF Isolation 22 30 32 LO to IF Isolation 22 29 29 31 dB RF to IF Isolation 31 42 42 42 dB 35 34 32 dBm IP3 (Input) 1 dB Compression (Input) LO Drive Input Level (Typical) Supply Current Icc total 23 -3 to +3 120 145 22 20 dBm -3 to +3 -3 to +3 dBm 100 70 mA * Unless otherwise noted all measurements performed as downconverter with high side LO & IF = 200 MHz. 10 - 1 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC687LP4 / 687LP4E v04.0509 BiCMOS MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 1.7 - 2.2 GHz Conversion Gain vs. Temperature Isolation 0 RF/IF LO/RF LO/IF -5 -10 +25 C +85 C -40 C -15 -20 1.6 1.7 1.8 1.9 2 -30 -40 -50 2.1 2.2 2.3 -60 1.6 2.4 1.7 1.8 RF FREQUENCY (GHz) 1.9 2 2.1 2.2 2.3 2.4 RF FREQUENCY (GHz) Conversion Gain vs. LO Drive Return Loss 0 0 -5 -5 RETURN LOSS (dB) CONVERSION GAIN (dB) 10 -20 -10 -3 dBm 0 dBm +3 dBm -15 -20 1.6 1.7 1.8 1.9 2 -10 -15 RF LO -20 -25 2.1 2.2 2.3 -30 1.2 2.4 1.4 1.6 RF FREQUENCY (GHz) 1.8 2 2.2 2.4 FREQUENCY (GHz) IF Bandwidth (LO= 2.2 GHz) Input P1dB vs. Temperature 0 30 -5 25 -15 P1dB (dBm) RESPONSE (dB) -10 -20 -25 20 -30 +25 C +85 C -40 C 15 IF Return Loss Conversion Gain -35 Mixers - SINGLE & DOUBLE BALANCED - SMT -10 ISOLATION (dB) CONVERSION GAIN (dB) 0 -40 -45 0 0.1 0.2 0.3 IF FREQUENCY (GHz) 0.4 0.5 10 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 2.4 RF FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 10 - 2 HMC687LP4 / 687LP4E v04.0509 BiCMOS MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 1.7 - 2.2 GHz Input IP3 vs. Temperature [1] 40 35 35 IP3 (dBm) 40 30 -3 dBm 0 dBm +3 dBm 25 20 1.6 1.7 1.8 1.9 2 +25 C +85 C -40 C 25 2.1 2.2 2.3 20 1.6 2.4 1.7 1.8 2.1 2.2 2.3 2.4 90 -2RF+2LO RESPONSE (dBc) -2RF +2LO RESPONSE (dBc) 2 -2RF +2LO Response vs. LO Drive [2] 90 +25 C +85 C -40 C 80 70 60 50 40 1.6 1.9 RF FREQUENCY (GHz) -2RF +2LO Response vs. Temperature [2] 1.7 1.8 1.9 2 2.1 2.2 2.3 70 60 50 40 1.6 2.4 -3 dBm 0 dBm +3 dBm 80 1.7 1.8 RF FREQUENCY (GHz) 1.9 2 2.1 2.2 2.3 2.4 RF FREQUENCY (GHz) -3RF +3LO Response vs. Temperature [2] -3RF +3LO Response vs. LO Drive [2] 90 -3RF+3LO RESPONSE (dBc) 90 85 80 75 +25 C +85 C -40 C 70 65 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 2.4 RF FREQUENCY (GHz) [1] Two-tone input power = +9 dBm each tone, 1 MHz spacing. 10 - 3 30 RF FREQUENCY (GHz) -3RF+3LO RESPONSE (dBc) Mixers - SINGLE & DOUBLE BALANCED - SMT 10 IP3 (dBm) Input IP3 vs. LO Drive [1] 85 80 75 -3 dBm 0 dBm +3 dBm 70 65 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 2.4 RF FREQUENCY (GHz) [2] Referenced to RF Input power at 0 dBm For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC687LP4 / 687LP4E v04.0509 BiCMOS MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 1.7 - 2.2 GHz Low Power Consumption Performance Input IP3 vs. G_Bias Voltage [1] -6 32 -7 30 -8 28 Vcc1, 2, 3 = 3.3 V R9 = 270 Ohms -10 -12 1.6 1.8 1.9 1V 1.5 V 2V 2.5 V 24 1V 1.5 V 2V 2.5 V 1.7 26 Vcc1, 2, 3 = 3.3 V R9 = 270 Ohms Icc = 67 mA 2 2.1 2.2 22 2.3 20 1.6 2.4 1.7 1.8 RF FREQUENCY (GHz) -6 36 -7 34 -8 32 -9 -11 -12 1.6 1.7 1.8 1.9 Vcc1, 2, 3 = 5.0 V R9 = 270 Ohms Icc = 120 mA 2 2.1 2.1 2.3 2.4 30 1.5 V 2V 2.5 V 3V 3.5 V 2.2 26 2.3 24 1.6 2.4 1.7 1.8 RF FREQUENCY (GHz) 1.9 2 2.1 2.2 2.3 2.4 RF FREQUENCY (GHz) Conversion Gain vs. Icc Input IP3 vs. Icc [1] -7 36 Vcc1, 2, 3 = 5.0 V G_Bias = 2.5 V 34 -8 IP3 (dBm) 32 -9 120 mA 110 mA 100 mA 90 mA 80 mA 70 mA -10 -11 1.6 2.2 Vcc1, 2, 3 = 5.0 V R9 = 270 Ohms Icc = 120 mA 28 1.5 V 2V 2.5 V 3V 3.5 V 2 Input IP3 vs. G_Bias Voltage [1] IP3 (dBm) CONVERSION GAIN (dB) Conversion Gain vs. G_Bias Voltage -10 1.9 RF FREQUENCY (GHz) 1.7 1.8 1.9 30 28 120 mA 110 mA 100 mA 90 mA 80 mA 70 mA 26 Vcc1, 2, 3 = 5.0 V G_Bias = 2.5 V 2 2.1 2.2 2.3 24 2.4 RF FREQUENCY (GHz) 22 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 Mixers - SINGLE & DOUBLE BALANCED - SMT -9 -11 CONVERSION GAIN (dB) 10 Icc = 67 mA IP3 (dBm) CONVERSION GAIN (dB) Conversion Gain vs. G_Bias Voltage 2.4 RF FREQUENCY (GHz) [1] Two-tone input power = +9 dBm each tone, 1 MHz spacing For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 10 - 4 HMC687LP4 / 687LP4E v04.0509 BiCMOS MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 1.7 - 2.2 GHz Low Power Consumption Performance Conversion Gain vs. Temperature, Icc = 70 mA Input IP3 vs. Temperature, Icc = 70 mA [1] 36 34 -7 32 -8 IP3 (dBm) 30 -9 -10 -12 1.6 28 26 24 1.7 1.8 1.9 2 +25 C +85 C -40 C 22 +25 C +85 C -40 C -11 20 2.1 2.2 2.3 18 1.6 2.4 1.7 1.8 RF FREQUENCY (GHz) 1.9 2 2.1 2.2 2.3 2.4 2.2 2.3 2.4 RF FREQUENCY (GHz) Icc vs. R9 130 120 Icc (mA) 110 Vcc1, 2, 3 = 5.0 V 100 90 80 70 60 250 300 350 400 450 500 550 600 R9 (Ohms) Typical Upconverter Performance Conversion Gain vs. LO Drive Input IP3 vs. LO Drive [1] 0 35 -5 30 IP3 (dBm) CONVERSION GAIN (dB) Mixers - SINGLE & DOUBLE BALANCED - SMT 10 CONVERSION GAIN (dB) -6 -10 -3 dBm 0 dBm +3 dBm -15 -20 1.6 1.7 1.8 1.9 2 2.1 25 -3 dBm 0 dBm +3 dBm 20 2.2 2.3 2.4 RF FREQUENCY (GHz) 15 1.6 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) [1] Two-tone input power = +9 dBm each tone, 1 MHz spacing. 10 - 5 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC687LP4 / 687LP4E v04.0509 BiCMOS MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 1.7 - 2.2 GHz Absolute Maximum Ratings MxN Spurious @ IF Port RF / IF Input (Vcc1, 2, 3 = +5V) +23 dBm LO Drive (Vcc1, 2, 3 = +5V) +10 dBm mRF 0 1 2 3 4 Vcc1,2,3 +5.5V 0 xx 20 27 54 28 Channel Temperature 125 C 1 43 0 39 31 57 2 64 60 59 68 87 3 110 81 102 77 96 4 115 129 115 115 112 0.83 mW Thermal Resistance (channel to ground paddle) 48.33 C/W Storage Temperature -65 to 150 C Operating Temperature -40 to +85 C RF Freq. = 1.9 GHz @ 0 dBm LO Freq. = 2.1 GHz @ 0 dBm All values in dBc below IF power level (-1RF + 1LO). ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Typical Supply Current vs. Vcc Vcc1, 2, 3 (V) Harmonics of LO Icc total (mA) nLO Spur @ RF Port 4.75 113 LO Freq. (GHz) 1 2 3 4 5.00 120 1.6 37 25 46 42 5.25 127 1.7 35 24 44 41 Downconverter will operate over full voltage range shown above. 1.8 33 23 43 42 1.9 30 22 36 36 2.0 29 23 40 28 2.1 29 24 44 27 2.2 32 24 42 31 2.3 34 24 42 38 LO = 0 dBm All values in dBc below input LO level measured at RF port. 10 Mixers - SINGLE & DOUBLE BALANCED - SMT Continuous Pdiss (T = 85C) (derate 20.69 mW/C above 85C) nLO [1] Two-tone input power = +9 dBm each tone, 1 MHz spacing. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 10 - 6 HMC687LP4 / 687LP4E v04.0509 BiCMOS MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 1.7 - 2.2 GHz Outline Drawing Mixers - SINGLE & DOUBLE BALANCED - SMT 10 10 - 7 NOTES: 1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED PLASTIC SILICA AND SILICON IMPREGNATED. 2. LEAD AND GROUND PADDLE MATERIAL: COPPER ALLOY. 3. LEAD AND GROUND PADDLE PLATING: 100% MATTE TIN. 4. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 5. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 6. PAD BURR LENGTH SHALL BE 0.15mm MAX. PAD BURR HEIGHT SHALL BE 0.25mm MAX. 7. PACKAGE WARP SHALL NOT EXCEED 0.05mm 8. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 9. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC687LP4 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 [1] HMC687LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 [2] Package Marking [3] H687 XXXX H687 XXXX [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC687LP4 / 687LP4E v04.0509 BiCMOS MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 1.7 - 2.2 GHz Pin Descriptions Pin Number Description N/C No connection. These pins may be connected to RF ground. Performance will not be affected. 2, 5, 15, 17 GND Package bottom must be connected to RF/DC ground. 3 RF This pin is matched single-ended 50 Ohm and DC shorted to ground through a balun. 4 TAP Center tap of secondary side of the internal RF balun. Short to ground with a zero ohm close to the IC. 8, 10, 24 Vcc1, Vcc2, Vcc3 Power supply voltage. See application circuit for required external components. 9 LO_BIAS LO buffer current adjustment pin. Adjust the LO buffer current through the external resistor R9 shown in the application circuit (connect 270 Ohms for nominal operation). This adjustment allows for a trade-off between power dissipation and linearity performance of the converter. 16 LO This pin is matched single-ended 50 Ohm and DC shorted to ground through a balun. 19 G_BIAS External bias. See application circuit for recommended external components. Apply +2.5V for nominal operation at 5V supply voltage. G_Bias can be set to between 0 and 5Vdc. The G_bias pin has an internal 15K ohm resistance to ground. This adjustment allows for a trade off between conversion loss and linearity performance of the converter (see figures CG, IP3 vs. G-Bias). 21, 22 IFN, IFP Differential IF input / output pins matched to differential 50 Ohms. For applications not requiring operation to DC an off chip DC blocking capacitor should be used. Interface Schematic For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 10 Mixers - SINGLE & DOUBLE BALANCED - SMT Function 1, 6, 7, 11 - 14, 18, 20, 23 10 - 8 HMC687LP4 / 687LP4E v04.0509 BiCMOS MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 1.7 - 2.2 GHz Evaluation PCB Mixers - SINGLE & DOUBLE BALANCED - SMT 10 List of Materials for Evaluation PCB 119935 [1] Item Description J1 - J3 SMA Connector J4 - J7 DC Pin C19 22 pF Capacitor, 0402 Pkg. C7, C8 10 nF Capacitor, 0402 Pkg. C10, C12, C16, C18 1 nF Capacitor, 0402 Pkg. C11, C15, C17, C21 0.1 F Capacitor, 0402 Pkg. C20 4.7 F Case A, Tantulum R2 - R4, R7, R8 0 Ohm Resistor, 0402 Pkg. R9 270 Ohm Resistor, 0603 Pkg. T1 1:1 Transformer - Tyco MABA CT0039 U1 HMC687LP4(E) Downconverter PCB [2] 118162 Evaluation PCB The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25R, FR4 10 - 9 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC687LP4 / 687LP4E v04.0509 BiCMOS MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 1.7 - 2.2 GHz Application Circuit Mixers - SINGLE & DOUBLE BALANCED - SMT 10 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 10 - 10 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: HMC687LP4E HMC687LP4ETR 119935-HMC687LP4