HTFS 200-P/SP2 - LEM - Product.Network

Current Transducer HTFS 200..800-P/SP2

For the electronic measurement of currents : DC, AC, pulsed, mixed,

with a galvanic isolation between the primary circuit (high power)

and the secondary circuit (electronic circuit).

All Data are given with a RL = 10 kΩ

Electrical data

Primary nominal Primary current Type RoHS since

current rms measuring range date code

IPN (A) IPM (A)

200 ± 300 HTFS 200-P/SP2 45326

400 ± 600 HTFS 400-P/SP2 45060

800 ± 1200 HTFS 800-P/SP2 45060

VOUT Output voltage (Analog) @ IPVREF ± (1.25·IP/IPN)V

IP = 0 VREF ± 0.025 V

VREF Reference voltage 1) - Output voltage 1/2VC ± 0.025 V

VREF Output impedance typ. 200 Ω

VREF Load impedance ≥ 200 kΩ

R L Load resistance ≥ 2 kΩ

ROUT Output internal resistance < 10 Ω

C L Capacitive loading < 1µF

VCSupply voltage (± 5 %) 5V

ICCurrent consumption @ VC = 5 V 22 mA

Accuracy - Dynamic performance data

XAccuracy 2) @ IPN , TA = 25°C ≤ ± 1 % of IPN

εLLinearity error 0 .. 1.5 x IPN ≤ ± 0.5 % of IPN

TCVOE Temperature coefficient of VOE @ IP = 0 ≤ ± 0.3 mV/K

TCVREF Temperature coefficient of VREF ≤ ± 0.01 %/K

TCVOUT / VREF Temperature coefficient of VOUT / VREF @ IP = 0 ≤ ± 0.2 mV/K

TCVOUT Temperature coefficient of VOUT ≤ ± 0.05% of reading/K

VOM Magnetic offset voltage @ IP = 0,

after an overload of 3 x IPN DC < ± 0.5 % of IPN

tra Reaction time @ 10 % of IPN < 3 µs

trResponse time to 90 % of IPN step < 7 µs

di/dt di/dt accurately followed > 100 A/µs

Vno Output voltage noise (DC ..10 kHz) < 15 mVpp

(DC .. 1 MHz) < 40 mVpp

BW Frequency bandwidth (-3 dB) 3) DC .. 20 kHz

General data

TAAmbient operating temperature - 40 .. + 105 °C

TSAmbient storage temperature - 40 .. + 105 °C

mMass 60 g

Standards EN 50178: 1997

Features

•Hall effect measuring principle

•Galvanic isolation between primary

and secondary circuit

•Low power consumption

•Single power supply +5V

•Ratiometric offset

•TA = -40..+105 °C

•PCB fixation by 4 Ø1 pins

•Insulated plastic case recognized

according to UL 94-V0

Advantages

•Small size and space saving

•Only one design for wide current

ratings range

•High immunity to external

interference.

•VREF. IN/OUT

Applications

•Forklift drives

•AC variable speed drives

•Static converters for DC motor drives

•Battery supplied applications

•Uninterruptible Power Supplies

(UPS)

•Switched Mode Power Supplies

(SMPS)

•Power supplies for welding

applications.

Application domain

•Industrial

IPN = 200 - 400 - 800A

070827/4 www.lem.com

LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice.

Page 1/3

Notes :1) It is possible to overdrive VREF with an external reference voltage

between 2 - 2.8 V providing its ability to sink or source approx. 2.5 mA.

2)Excluding offset.

3)Small signal only to avoid excessive heatings of the magnetic core.

070827/4 www.lem.com

LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice.

Page 2/3

Current Transducer HTFS 200..800-P/SP2

Isolation characteristics

VbRated isolation voltage rms 150 V

with IEC 61010-1 standards and following conditions

-Single insulation

-Over voltage category III

-Pollution degree 2

-Heterogeneous field

VbRated isolation voltage rms 150 V

with EN 50178 standards and following conditions

-Reinforced insulation

-Over voltage category III

-Pollution degree 2

-Heterogeneous field

VdRms voltage for AC isolation test, 50 Hz, 1 min 2.5 kV

VePartial discharge extinction voltage rms @ 10pC > 1 kV

VwImpulse withstand voltage 1.2/50 µs4 kV

dCp Creepage distance > 4 mm

dCl Clearance distance > 4 mm

CTI Comparative tracking index (Group IIIa) > 220

If insulated cable is used for the primary circuit, the

voltage category could be improved with the following table :

Cable insulation (primary) Category

HAR 03 300V CAT III

HAR 05 400V CAT III

HAR 07 500V CAT III

Safety

This transducer must be used in electric/electronic equipment with respect to

applicable standards and safety requirements in accordance with the following

manufacturer's operating instructions.

Caution, risk of electrical shock

When operating the transducer, certain parts of the module can carry hazardous

voltage (eg. primary busbar, power supply).

Ignoring this warning can lead to injury and/or cause serious damage.

This transducer is a built-in device, whose conducting parts must be inaccessible

after installation.

A protective housing or additional shield could be used.

Main supply must be able to be disconnected.

3-P=2.54

Terminal Pin

+5V

Output

47nF

47nFOutput

+5V

1...+5V

2...0V

3...Output

4.5

4...Vref(IN/OUT)

4-0.25x0.5

16.5

Vref(IN/OUT)

HTFS

20.3

0.5

3.5+/-1

d22

Vref(IN/OUT)

4.7nF

4-d=1.0

Mechanical characteristics

•General tolerance ± 0.2 mm

•Fixation 4 pins x Ø 1.0

•Recommended PCB hole Ø 1.2 mm

•Fastening & connection of secondary 4 pins 0.5 x 0.25

Recommended PCB hole Ø 0.7 mm

Remarks

•VOUT is positive when IP flows in the direction of the arrow.

•Temperature of the primary conductor should not exceed

120°C.

Ip 0V

Vref.(IN/OUT)

Vout

+Vc

Required Connection Circuit

Operation Principle

070827/4 www.lem.com

LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice.

Page 3/3

Dimensions HTFS 200..800-P/SP2 (in mm. 1 mm = 0.0394 inch)