TEN 30-4810WI - TRACO Power

http://www.tracopower.com

Features

◆ Ultra wide 4:1 input voltage range

◆ Single output voltage models

from 1.8 to 15 VDC

◆ Dual output voltage models

◆ Extended operating temperature range:

–40°C to 85°C

◆ Under voltage lockout

◆ Remote On/Off

◆ Shielded metal case with insulated

baseplate

◆ Optional heatsink

◆ Lead free design - RoHS compliant

◆ 3-year product warranty

DC/DC Converters

TEN 30WI Series, 30 Watt

The TEN 30WI series is a family of high performance 30W dc-dc converters fea-

turing ultra wide 4:1 input voltage ranges in a compact low proﬁle package with

industry-standard footprint. A very high efﬁciency allows operating temperatures

up to 85°C. A built-in ﬁlter for both input and output minimizes the need for external

ﬁltering. Further standard features include remote On/Off, output voltage trimming,

over voltage protection, under voltage lockout and short circuit protection.

Typical applications for these products are battery operated equipment and distrib-

uted power architectures in communication and industrial electronics, everywhere

where isolated, tightly regulated voltages are required and space is limited on the

PCB.

Order code Input voltage range Output voltage Output current max. Efﬁciency typ.

TEN 30-2408WI 1.8 VDC 8‘000 mA 80 %

TEN 30-2409WI 2.5 VDC 8’000 mA 85 %

TEN 30-2410WI 3.3 VDC 6’000 mA 87 %

TEN 30-2411WI 10 – 40 VDC 5.0 VDC 6‘000 mA 87 %

TEN 30-2412WI (nominal 24 VDC) 12 VDC 2’500 mA 87 %

TEN 30-2413WI 15 VDC 2’000 mA 88 %

TEN 30-2422WI ±12 VDC ±1’250 mA 85 %

TEN 30-2423WI ±15 VDC ±1’000 mA 86 %

TEN 30-4808WI 1.8 VDC 8‘000 mA 81 %

TEN 30-4809WI 2.5 VDC 8’000 mA 86 %

TEN 30-4810WI 3.3 VDC 6’000 mA 87 %

TEN 30-4811WI 18 – 75 VDC 5.0 VDC 6‘000 mA 88 %

TEN 30-4812WI (nominal 48 VDC) 12 VDC 2’500 mA 87 %

TEN 30-4813WI 15 VDC 2’000 mA 88 %

TEN 30-4822WI ±12 VDC ±1’250 mA 86 %

TEN 30-4823WI ±15 VDC ±1’000 mA 87 %

Models

Page 1 of 4

http://www.tracopower.com

Input Specifications

Input current at no load 1.8 Vout models: 35 / 20 mA typ.

(nominal input 24/48 Vin) 2.5/3.3 Vout models: 40 / 25 mA typ.

other models: 70 / 45 mA typ.

Input current at full load 1.8 Vout models: 760 / 380 mA typ.

(nominal input 24/48 Vin) 2.5/3.3 Vout models: 1030 / 510 mA typ.

other models: 1500 / 750 mA typ.

Input voltage variation (dv/dt) 5 V/ms, max.

(complies with ETS 300 132 part. 4.4)

Start-up voltage / under voltage lockout 24 Vin models: 10 VDC / 8 VDC (typ.)

48 Vin models: 18 VDC / 16 VDC (typ.)

Surge voltage (100 msec. max.) 24 Vin models: 50 V max.

48 Vin models: 100 V max.

Conducted noise (input) EN 55022 level A, FCC part 15, level A with

external capacitor (see note 1)

ESD (input) EN 61000-4-2, perf. criteria B

Fast transient (input) EN 61000-4-4, perf. criteria A

Surge (input) EN 61000-4-5, perf. criteria B

Output Specifications

Voltage set accuracy ±1 %

Output voltage adjustment ±10 %

Regulation – Input variation Vin min. to Vin max. ±0.5 % max.

– Load variation 10 – 100 %: single output models: ±0.5 % max.

dual output models: ±1.0 % max. (balanced load)

±5 % max. (Load cross variation 25 % / 100 %)

Temperature coefficient ±0.02 %/K

Ripple and noise (20 MHz Bandwidth): 75 mVpk-pk max.

Start up time (nominal Vin and constant resistive load) 10 ms typ.

Transient response setting time (25% load step change) 300 µs typ.

Short circuit protection indefinite (automatic recovery)

Over load protection 150 % of Iout max typ. foldback

Thermal shutdown at +115°C typ

Over voltage protection 1.8, 2.5 & 3.3 V output models: 3.9 V

5.0 V output models: 6.2 V

12 V output models: 15 V

15 V output models: 18 V

Minimum load (only for dual output models) 10% of rated max current

(operation at lower load

condition will not damage these converters, however,

they may not meet all listed specifications)

Capacitive load 1.8 / 2.5 Vout models: 65’000 µF max./ 33’000 µF max.

3.3 / 5.0 Vout models: 19’500 µF max./ 10’200 µF max.

12 / 15 Vout models: 3’300 µF max./ 1’100 µF max.

±12 / ±15 Vout models: ±1’000 µF max./ ±680 µF max. (per output)

DC/DC Converters

TEN 30WI 30 Watt

All speciﬁcations valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.

Page 2 of 4

http://www.tracopower.com

DC/DC Converters

TEN 30WI 30 Watt

General Specifications

Temperature ranges – Operating –40°C to +85°C (with derating)

– Case temperature +100°C max.

– Storage –55°C to +105°C

Thermal impedance – with heat-sink TEN-HS2 8.24 K/Watt

– without heat-sink 10 K/Watt

Humidity (non condensing) 95 % rel H max.

Reliability, calculated MTBF (MIL-HDBK-217F, at +25°C, ground benign) >750’000 h

Isolation voltage (60sec.) – Input / Output 1‘500 VDC

Isolation resistance – Input / Output >1‘000 M Ohm

Isolation capacitance – Input / Output 1000 pF max.

Remote On/Off – On: 3.5 ... 12 VDC or open circuit.

– Off: 0 ... 1.2 VDC or short circuit pin 3 and pin 2

– Off idle current: 3 mA typ.

Switching frequency 300 kHz typ. (pulse width modulation PWM)

Vibration 10–55 Hz, 2G, 30 minutes along X,Y,Z

Safety approvals UL 60950, IEC/EN 60950, compliance

up to 60 VDC input voltage (SELV limit)

– Certification documents www.tracopower.com/overview/ten30wi

Environmental compliance – Reach www.tracopower.com/info/reach-declaration.pdf

– RoHS RoHS directive 20011/65/EU

Output Voltage Adjustment

Trim

+Vout

Trim

Vout

Trim up

Ru [kohm]*

output 1.8V 2.5V 3.3V 5.0V

+5% 1.2 4.3 6.8 4.7

+10% 0.068 0.82 1.5 0.56

output 12V 15V ±12V ±15V

+5% 47 47 27 33

+10% 8.2 6.8 2.2 2.7

Trim down

Ru [kohm]*

output 1.8V 2.5V 3.3V 5.0V

–5% 1.8 6.8 8.2 5.6

–10% 0.1 0.82 0.68 0.68

output 12V 15V ±12V ±15V

–5% 56 56 33 39

–10% 5.6 2.2 2.7 3.3

All speciﬁcations valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.

Page 3 of 4

Note 1:

In order to meet conducted emissions EN55022-A and EN55011-A a capacitor between +Vin and -Vin has to be installed. The capacitor

should be capable to handle 1 A ripple current. A suggestion is KMF Series of Nippon chemi-con, 220µF/100V, ESR 90mOhm.

*approximate values

Supporting documents: www.tracopower.com/overview/ten30wi

Speciﬁcations can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com

www.tracopower.com

Outline Dimensions

Pin Single Dual

1+Vin (Vcc) +Vin (Vcc)

2–Vin (GND) –Vin (GND)

3Remote On/Off

4No pin +Vout

5+Vout Common

6–Vout –Vout

7Trim

Pin-Out

Rev. July 13, 2018

Physical Specifications

Casing material copper, nickel plated

Baseplate material none conductive FR4

Potting material epoxy (UL 94V-0 -rated)

Weight 48 g (1.69 oz)

Soldering temperature max. 265°C / 10 sec.

Heat-sink TEN-HS2

56.0

(2.2)

max.

23.0 (0.9)

17.2 (0.68)

max.

Converter

Heat-sink

Thermal pad

Clamp

5.6 10.2

40.6

10.16 10.16 10.16

5.08

50.8

Bottom

view

45.72

(2.0)

(0.22)

(1.6)

(0.4)

(0.4) (0.4)

(0.2)

(1.8)

12.7

(0.5)

5.1

(0.2)

10.16

(0.4)

Page 4 of 4

DC/DC Converters

TEN 30WI 30 Watt

Dimensions in [mm], () = Inch

Pin diameter: 1.0 ±0.05 (0.02 ±0.002)

Pin pitch tolerances: ±0.35 (±0.014)

Case tolerances: ±0.5 (±0.02)

Note:

The product label on converter has to be removed before

mounting the heat-sink. For volume orders converters will

be supplied with heat-sinks already mounted. Please con-

tact factory for quotation. Separate heat-sinks are only

available for prototypes and small quantity orders.

Order code: TEN-HS2

(cont.: heat-sink, thermal pad, 2 clamps)

Material: Aluminum

Finish: Anodic treatment (black)

Weight: 19 g (0.67oz) (without converter)

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

TRACO Power:

TEN 30-4811WI TEN 30-2412WI TEN 30-2410WI TEN 30-2413WI TEN 30-2411WI TEN 30-4810WI TEN 30-

4808WI TEN 30-4822WI TEN 30-2423WI TEN 30-4823WI TEN 30-2422WI TEN 30-4812WI TEN 30-2409WI TEN

30-4809WI TEN 30-2408WI TEN 30-4813WI