GaAs INTEGRATED CIRCUIT PG2164T5N DPDT SWITCH FOR 2.4 GHz AND 6 GHz DUAL-BAND WIRELESS LAN DESCRIPTION The PG2164T5N is a GaAs MMIC DPDT (Double Pole Double Throw) switch which was developed for 2.4 GHz and 6 GHz dual-band wireless LAN. This device can operate frequency from 2.4 GHz band and 6 GHz band, having the low insertion loss and high isolation. This device is housed in a 6-pin plastic TSON (Thin Small Out-line Non-leaded) package. And this package is able to high-density surface mounting. FEATURES * Operating frequency : f = 2.4 to 2.5 GHz and 4.9 to 6.0 GHz * Switch control voltage : Vcont (H) = 2.8 to 5.0 V (3.0 V TYP.) : Vcont (L) = 0.3 to 0.3 V (0 V TYP.) * Low insertion loss : Lins1 = 0.50 dB TYP. @ f = 2.4 to 2.5 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : Lins2 = 0.70 dB TYP. @ f = 4.9 to 6.0 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V * High isolation : ISL1 = 25 dB TYP. @ f = 2.4 to 2.5 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : ISL2 = 17 dB TYP. @ f = 4.9 to 6.0 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V * Handling power : Pin (1 dB) = +31.0 dBm TYP. @ f = 2.5 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : Pin (1 dB) = +29.0 dBm TYP. @ f = 6.0 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V * High-density surface mounting : 6-pin plastic TSON package (1.5 1.5 0.37 mm) APPLICATION * Dual-band wireless LAN (IEEE802.11a + b/g) ORDERING INFORMATION Part Number Order Number PG2164T5N-E2 PG2164T5N-E2-A Package 6-pin plastic TSON (Pb-Free) Marking G5B Supplying Form Embossed tape 8 mm wide Pin 1, 6 face the perforation side of the tape Qty 3 kpcs/reel Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: PG2164T5N-A Caution: Observe precautions when handling because these devices are sensitive to electrostatic discharge Document No. PG10636EJ02V0DS (2nd edition) Date Published February 2008 NS The mark <R> shows major revised points. The revised points can be easily searched by copying an "<R>" in the PDF file and specifying it in the "Find what:" field. PG2164T5N PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM Pin No. Pin Name 1 ANT2 2 Vcont2 3 OUT2 (RX) 4 OUT1 (TX) 5 Vcont1 6 ANT1 Remark Exposed pad : GND TRUTH TABLE Vcont1 Vcont2 ANT1OUT1 (TX) ANT1 OUT2 (RX) ANT2 OUT1 (TX) ANT2OUT2 (RX) High Low OFF ON ON OFF Low High ON OFF OFF ON ABSOLUTE MAXIMUM RATINGS (T A = +25C, unless otherwise specified) Parameter Symbol Ratings Unit Vcont 6.0 to +6.0 V Input Power Pin +32 dBm Operating Ambient Temperature TA 45 to +85 C Storage Temperature Tstg 55 to +135 C Switch Control Voltage RECOMMENDED OPERATING RANGE (T A = +25C, unless otherwise specified) Parameter Symbol MIN. TYP. MAX. Unit Switch Control Voltage (H) Vcont (H) 2.8 3.0 5.0 V Switch Control Voltage (L) Vcont (L) 0.3 0 0.3 V Operating Frequency 1 f1 2.4 2.5 GHz Operating Frequency 2 f2 4.9 6.0 GHz 2 Data Sheet PG10636EJ02V0DS PG2164T5N ELECTRICAL CHARACTERISTICS (T A = +25C, Vcont (H) = 3.0 V, Vcont otherwise specified) Parameter Symbol (L) = 0 V, Z0 = 50 , DC blocking capacitors = 4 pF, unless Test Conditions MIN. TYP. MAX. Unit Insertion Loss 1 Lins1 f = 2.4 to 2.5 GHz 0.50 0.75 dB Insertion Loss 2 Lins2 f = 4.9 to 6.0 GHz 0.70 1.00 dB Isolation 1 (ANT to OUT) ISL1 f = 2.4 to 2.5 GHz 22 25 dB Isolation 2 (ANT to OUT) ISL2 f = 4.9 to 6.0 GHz 14 17 dB Isolation 3 (ANT1 to ANT2, TX to RX) ISL3 f = 2.4 to 2.5 GHz 22 25 dB Isolation 4 (ANT1 to ANT2, TX to RX) ISL4 f = 4.9 to 6.0 GHz 15 17 dB Input Return Loss 1 RLin1 f = 2.4 to 2.5 GHz 15 dB Input Return Loss 2 RLin2 f = 4.9 to 6.0 GHz 15 dB Output Return Loss 1 RLout1 f = 2.4 to 2.5 GHz 15 dB Output Return Loss 2 RLout2 f = 4.9 to 6.0 GHz 15 dB 1 dB Loss Compression Note Input Power 1 Pin (1 dB) 1 f = 2.4 to 2.5 GHz +31.0 dBm 1 dB Loss Compression Note Input Power 2 Pin (1 dB) 2 f = 4.9 to 6.0 GHz +29.0 dBm +50 dBm 0.1 1.0 A 50 ns Input 3rd Order Intercept Point IIP3 f1 = 2 500 MHz, f2 = 2 501 MHz, Pin (1 tone) = +20 dBm Switch Control Current Icont Switch Control Speed tSW 50% CTL to 90/10% Note Pin (1 dB) is measured the input power level when the insertion loss increases more 1 dB than that of linear range. Caution This device is used it is necessary to use DC blocking capacitors. Data Sheet PG10636EJ02V0DS 3 PG2164T5N EVALUATION CIRCUIT The application circuits and their parameters are for reference only and are not intended for use in actual design-ins. 4 Data Sheet PG10636EJ02V0DS PG2164T5N MOUNTING PAD AND SOLDER MASK LAYOUT DIMENSIONS 6-PIN PLASTIC TSON (UNIT: mm) Remark The mounting pad and solder mask layouts in this document are for reference only. Data Sheet PG10636EJ02V0DS 5 PG2164T5N <R> PACKAGE DIMENSIONS 6-PIN PLASTIC TSON (UNIT: mm) 6 Data Sheet PG10636EJ02V0DS PG2164T5N RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. For soldering methods and conditions other than those recommended below, contact your nearby sales office. Soldering Method Infrared Reflow Wave Soldering Partial Heating Soldering Conditions Condition Symbol Peak temperature (package surface temperature) : 260C or below Time at peak temperature : 10 seconds or less Time at temperature of 220C or higher : 60 seconds or less Preheating time at 120 to 180C : 12030 seconds Maximum number of reflow processes : 3 times Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below Peak temperature (molten solder temperature) : 260C or below Time at peak temperature : 10 seconds or less Preheating temperature (package surface temperature) : 120C or below Maximum number of flow processes : 1 time Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below Peak temperature (terminal temperature) : 350C or below Soldering time (per side of device) : 3 seconds or less Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below IR260 WS260 HS350 Caution Do not use different soldering methods together (except for partial heating). Data Sheet PG10636EJ02V0DS 7 PG2164T5N Caution GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. * Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. * Do not burn, destroy, cut, crush, or chemically dissolve the product. * Do not lick the product or in any way allow it to enter the mouth. 8 Data Sheet PG10636EJ02V0DS