TS1003 Demo Board
Page 1
© 2014 Silicon Laboratories, Inc. All rights reserved.
REVISION NOTE
The current revisions for the TS1003 Demo Boards
display the identifier TS100x Demo Board on the
top side of the evaluation board as depicted in
Figure 1. If the identifier is not printed on the top
side of the evaluation board, please contact Silicon
Labs for support at:
https://www.silabs.com/support/pages/contacttechnicalsu
pport.aspx
COMPONENT LIST
DESIGNATION QTY DESCRIPTION
C1, C2, C3, C5 4 0.1µF ± 10%
capacitors (0805)
C4, C6 2 1µF ±10%
capacitors (0805)
R2 1 665kΩ ± 1%
resistor (0805)
R7 1 500kΩ ± 1%
resistor (0805)
R5, R6, R10 3 1MΩ ± 1%
resistors (0805)
R8, R9 2 1.25MΩ ± 1%
resistors (0805)
R1, R3, R4 3 2MΩ ± 1%
resistors (0805)
U1, U2 2 TS1003
operational
amplifiers
V
DD
,V
in
,V
out
,GND 11 Test points
FEATURES
0.8V to 5.5V Single-supply operation
AC-coupled Non-Inverting and Inverting
configuration supplied
Fully Assembled and Tested
2in x 2in 2-layer demo board
DESCRIPTION
The demo board for the TS1003 is a completely
assembled and tested circuit board that can be used
for evaluating the TS1003. The TS1003 is the
industry’s first sub-1µA supply current, precision
CMOS operational amplifier fully specified to operate
over a supply voltage range from 0.8V to 5.5V. Fully
specified at 1.8V, the TS1003 is optimized for ultra-
long-life battery powered applications. The TS1003
exhibits a typical input bias current of 2pA, and rail-to-
rail input and output stages.
The TS1003 is fully specified over the industrial
temperature range (-40°C to +85°C). The TS1003
evaluation board is offered with either a PCB-space
saving 5-lead SC70 or 5-lead SOT23 p ackaging.
Product data sheets and additional documentation
can be found at www.silabs.com.
Ordering Information
Order Number Description
TS1003DB SC70 Packaging
Demo Board
TS1003DB-SOT SOT23 Packaging
Demo Board
Figure 1. TS1003 Evaluation Board Top View Figure 2. TS1003 Evaluation Board Bottom View
TS1003 Demo Board
TS1003-EVB Rev. 1.0 Page 2
Description
The TS1003 evaluation boards provide two
configurations for evaluating the TS1003 operational
amplifier in one single PCB board, namely a non-
inverting configuration located on the left-hand side of
the board and an inverting configuration located on
the right-hand side of the board. In both cases, the
input to each circuit is AC-coupled. The demo board
provides a re-biasing scheme at one-half the power
supply or VDD/2 for the inverting configuration and at
VDD/4 for the non-inverting configuration.
The TS1003 demo board provides a dedicated power
supply for the non-inverting circuit and a dedicated
power supply for the inverting circuit. This provides
the user the flexibility of evaluating one circuit at a
time or both at the same time.
In both the non-inverting and the inverting
configuration, the AC-coupling capacitor creates a
high pass filter. The resulting cut-off frequency, fC, is
given as:
fC= 1
2πRC
In the non-inverting circuit, R=R5=1MΩ and
C=C5=0.1µF. In the inverting case, R=R10=1MΩ and
C=C1=0.1µF. In both cases, these component values
generate a high-pass cut-off frequen cy of 1.6Hz.
Default Configurations
Non-Inverting configuration
In the non-inverting configuration, the circuit’s transfer
function is given by the following equation:
VOUT
VIN = 1+ R4
R3
With R4=2MΩ and R3=2MΩ the circuit signal gain is
2 with a circuit bandwidth of 2kHz. This results in an
overall circuit bandwidth range of 1.6Hz to 2kHz.
Inverting configuration
In an inverting configuration, the circuit’s transfer
function is given by the following equation:
VOUT
VIN = -R6
R10
In this case, R6=1MΩ and R10=1MΩ. This results in
a signal gain of -1 with a circuit bandwidth of 2kHz
and an overall circuit bandwidth range of 1.6Hz to
2kHz.
Quick Start Procedures
Required Equipment
TS1003 demo board
DC Power Supply, Single or Dual Output
Function Generator
4-channel Oscilloscope
Two 1MΩ oscilloscope probes
Non-Inverting Configuration
In order to evaluate the TS1003 operational amplifier
in the non-inverting configuration, the following steps
are to be performed:
1) Before connecting the DC power supply to the
demo board power test points, turn on the power
supply and set the DC voltage to 5.5V and then
turn it off.
2) Set the function generator frequency to 500Hz
and output level with a VOH = 2.35V and a VOL =
2.15V. This sets the input signal swing to
200mVPP, centered at 2.25V.
3) In order to monitor the input and output signal,
select two channels on the oscilloscope and set
the vertical voltage scale and the vertical position
on each channel to 100mV/DIV and -2.25V,
respectively. Set the horizontal time scale to
500µs/DIV.
4) Connect the positive terminal of the DC power
supply to VDD and the ground terminal to GND.
TS1003 Demo Board
TS1003-EVB Rev. 1.0 Page 3
5) Connect the signal output of the function
generator to V
in
and the ground terminal to GND.
6) To monitor the input, connect the signal terminal
of one of the oscilloscope probes to V
in
and the
ground terminal to GND. To monitor the output,
use the second probe to connect the signal
terminal to V
OUT
and the ground terminal to GND.
7) Turn on the power supply and check that the
power supply current is approximately 3.6µA.
8) Turn on the function generator.
9) Observe the input and output signal. The output
signal is an amplified version of the input signal
with an output swing of approximately 400mV
PP
,
corresponding to a signal gain of two.
Inverting Configuration
In order to evaluate the TS1003 operational amplifier
in the inverting configuration, the following steps are
to be performed:
1) Before connecting the DC power supply to the
demo board, turn on the power supply and set
the DC voltage to 5.5V and then turn it off.
2) Set the function generator output frequency to
500Hz and output level with a V
OH
= 2.35V and a
V
OL
= 2.15V. This sets the input swing to
200mV
PP
, centered at 2.25V.
3) In order to monitor the input and output signal,
select two channels on the oscilloscope and set
the vertical voltage scale and the vertical position
on each channel to 100mV/DIV and -2.25V,
respectively. Set the horizontal time scale to
500µs/DIV.
4) Connect the positive terminal of the DC power
supply to VDD and the ground terminal to GND.
5) Connect the signal output of the function
generator to V
in
and the ground terminal to GND.
6) To monitor the input, connect the signal terminal
of one of the oscilloscope probes to V
in
and the
ground terminal to GND. To monitor the output,
use the second probe to connect the signal
terminal to V
OUT
and the ground terminal to GND.
7) Turn on the power supply and check that the
power supply current is approximately 3.0µA.
8) Turn on the function generator.
9) Observe the input and output signal. The output
signal is an inverted version of the input signal
and the swing should be 200mV
PP
.
Figure 4. Inverting Configuration
Figure 3. Non-Inverting Configuration
TS1003 Demo Board
Silicon Laboratories, Inc. Page 4
400 West Cesar Chavez, Austin, TX 78701 TS1003-EVB Rev. 1.0
+1 (512) 416–8500 ▪ www.silabs.com
Figure 5. TS1003 Demo Board
Top Layer #1
Figure 6. TS1003 Demo Board
Top Layer #2
Figure 7. TS1003 Demo Board
Bottom Layer (GND) #1
Figure 8. TS1003 Demo Board
B
otto
m L
aye
r
(G
ND
)
#
2
Disclaimer
Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers
using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific
device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories
reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy
or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply
or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific
written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected
to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no
circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations
thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®,
USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of
ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders.
http://www.silabs.com
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
Smart.
Connected.
Energy-Friendly
Products
www.silabs.com/products Quality
www.silabs.com/quality Support and Community
community.silabs.com
