OFFLINE GATE DRIVE TRANSFORMERS UL and C-UL recognized, TUV approved components 3000Vrms gate to drive winding test Useful operating frequency from 50kHz to 500kHz Most popular winding configurations Electrical Specifications @ 25C -- Operating Temperature -40C to 130C Reference Data Part 4 Number Turns Ratio ET Maximum (V * sec MAX) Flux Density Primary Inductance (1-10) (H MIN) Leakage Inductance Gate to Drive (H MAX) DCR Drive (1-10) (m 20%) DCR Gates (m 20%) Drive Pri-Sec (Vrms) P0584 1:1:1 95.0 2100 450 0.5 80 72 3000 P0585 1:1:1:1:1 95.0 2100 450 3.0 330 180 3000 NOTES: 1. These gate drive transformers are meant to operate between 50 and 300kHz with a 12V, 45% bipolar waveform. 2. The peak flux density should remain below 2100 Gauss to ensure that the core does not saturate. Use the following procedure to calculate the peak flux density: A. Calculate the Volt-sec product (ET): ET = 103 * (Drive Voltage) * (Don) / (Frequency in kHz) B. Calculate the operating flux density (B): Bpk (Gauss) = 40.32 * ET/Ff where: Ff = 1 for unipolar drive applications and 2 for bipolar drive applications 3. The temperature rise of the component is calculated based on the total core loss and copper loss: A. To calculate total copper loss (W), use the following formula: Copper Loss (W) = Irms2 * (DCR_Drive + (# of Gates) * DCR_Gates) B. To calculate total core loss (W), use the following formula: Core Loss (W) = 7.5E-5 * (Frequency in kHz)1.67 * (20.16 * ET/1000)2.532 C. To calculate temperature rise, use the following formula: Temperature Rise (C) = 60.18 * (Core Loss(W) + Copper Loss (W)).833 4. To order RoHS compliant part, add the suffix "NL" to the part number (i.e. P0584 becomes P0584NL). Mechanical .810 MAX 20,57 Schematics .480 MAX 12,19 P0584 Pri P0585 Sec .750 MAX 19,05 1 4 8 P058X Date Code Country of Origin 10 7 .130 3,30 P0584 (6 pins) 1 4 10 7 10 .350 8,89 1 2 3 .700 17,78 GATE 1 8 4 DRIVE 10 GATE 5 7 GATE P0585 (10 pins) 7 10 .350 8,89 (6X) .040 .200 5,08 GATE 3 9 4 1 .700 17,78 .400 10,16 6 7 .100 2,54 (10X) .040 .200 5,08 .100 2,54 4 Weight . . . . . . . . . . . . . . . .5 grams Tray . . . . . . . . . . . . . . . . . . .20/tray Dimensions: Inches mm Unless otherwise specified, all tolerances are .010 0,25 SUGGESTED PCB HOLE PATTERN For More Information: Pulse Worldwide Headquarters Pulse Northern Europe Pulse Southern Europe Pulse Pulse North China China Headquarters Room 1503 12220 World Trade Drive San Diego, CA 92128 U.S.A. www.pulseeng.com TEL: 858 674 8100 FAX: 858 674 8262 3 Huxley Road Surrey Research Park Guildford, Surrey GU2 5RE United Kingdom TEL: 44 1483 401700 FAX: 44 1483 401701 Zone Industrielle F-39270 Orgelet France TEL: 33 3 84 35 04 04 FAX: 33 3 84 25 46 41 No. 1 Industrial District Changan, Dongguan China TEL: 86 769 85538070 FAX: 86 769 85538870 XinYin Building No. 888 YiShan Road Shanghai 200233 China TEL: 86 21 54643211/2 FAX: 86 21 54643210 Pulse South Asia Pulse North Asia 150 Kampong Ampat #07-01/02 KA Centre Singapore 368324 No. 26 Kao Ching Road Yang Mei Chen Taoyuan Hsien Taiwan, R. O. C. TEL: 886 3 4641811 FAX: 886 3 4641911 TEL: 65 6287 8998 FAX: 65 6280 0080 Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. (c) Copyright, 2006. Pulse Engineering, Inc. All rights reserved. www.pulseeng.com P515.B (3/06)