Order Now Product Folder Support & Community Tools & Software Technical Documents LM2991 SNVS099I - MAY 1999 - REVISED OCTOBER 2016 LM2991 Negative Low-Dropout Adjustable Regulator 1 Features * 1 * * * * * * * 3 Description The LM2991 is a low dropout adjustable negative regulator with a output voltage range between -3 V to -24 V. The LM2991 provides up to 1 A of load current and features a ON /OFF pin for remote shutdown capability. Output Voltage Adjustable from -3 V to -24 V, Typically -2 V to -25 V Output Current in Excess of 1 A Dropout Voltage Typically 0.6 V at 1-A Load Low Quiescent Current Internal Short Circuit Current Limit Internal Thermal Shutdown With Hysteresis TTL, CMOS Compatible ON/OFF Switch Functional Complement to the LM2941 Series The LM2991 uses new circuit design techniques to provide a low dropout voltage, low quiescent current and low temperature coefficient precision reference. The dropout voltage at 1-A load current is typically 0.6 V and an ensured worst-case maximum of 1 V over the entire operating temperature range. The quiescent current is typically 1 mA with a 1-A load current and an input-output voltage differential greater than 3 V. A unique circuit design of the internal bias supply limits the quiescent current to only 9 mA (typical) when the regulator is in the dropout mode (VOUT - VIN 3 V). 2 Applications * * * * * Post Switcher Regulator Local, On-Card, Regulation Battery Operated Equipment Industrial Instrumentation The LM2991 is short-circuit proof, and thermal shutdown includes hysteresis to enhance the reliability of the device when inadvertently overloaded for extended periods. The LM2991 is available in 5lead TO-220 and DDPAK/TO-263 packages and is rated for operation over the automotive temperature range of -40C to +125C. Mil-Aero versions are also available. Device Information(1) PART NUMBER LM2991 PACKAGE BODY SIZE (NOM) DDPAK/TO-263 (5) 10.20 mm x 9.00 mm TO-220 (5) 14.99 mm x 10.16 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. Typical Application GND R1 + + CIN* COUT** ADJ Unregulated Input IN LM2991 OUT R2 Regulated Input ON/OFF Copyright (c) 2016, Texas Instruments Incorporated VOUT = VREF (1 + R2/R1) * Required if the regulator is located further than 6 inches from the power supply filter capacitors. A 1-F solid tantalum or a 10-F aluminum electrolytic capacitor is recommended. ** Required for stability. Must be at least a 10-F aluminum electrolytic or a 1-F solid tantalum to maintain stability. May be increased without bound to maintain regulation during transients. Locate the capacitor as close as possible to the regulator. The equivalent series resistance (ESR) is critical, and should be less than 10 over the same operating temperature range as the regulator. 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LM2991 SNVS099I - MAY 1999 - REVISED OCTOBER 2016 www.ti.com Table of Contents 1 2 3 4 5 6 7 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 4 6.1 6.2 6.3 6.4 6.5 6.6 4 4 4 4 5 6 Absolute Maximum Ratings ...................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Thermal Information .................................................. Electrical Characteristics........................................... Typical Characteristics .............................................. Detailed Description .............................................. 9 7.1 7.2 7.3 7.4 Overview ................................................................... 9 Functional Block Diagram ......................................... 9 Feature Description................................................... 9 Device Functional Modes........................................ 10 8 Application and Implementation ........................ 11 8.1 Application Information............................................ 11 8.2 Typical Application ................................................. 11 9 Power Supply Recommendations...................... 15 10 Layout................................................................... 16 10.1 Layout Guidelines ................................................. 16 10.2 Layout Example .................................................... 16 11 Device and Documentation Support ................. 17 11.1 11.2 11.3 11.4 11.5 11.6 11.7 Device Support .................................................... Related Documentation ....................................... Receiving Notification of Documentation Updates Community Resources.......................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 17 17 17 17 17 18 18 12 Mechanical, Packaging, and Orderable Information ........................................................... 18 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision H (June 2013) to Revision I Page * Added Device Information and ESD Rating tables, Feature Description, Device Functional Modes, Application and Implementation, Power Supply Recommendations, Layout, Device and Documentation Support, and Mechanical, Packaging, and Orderable Information sections; moved some curves to Application Curves section .................................. 1 * Changed footnote 4 of Abs Max table and footnote 1 to Typical Characteristics to eliminate obsolete thermal values for thetaJA; updated values are in Thermal Information ....................................................................................................... 4 * Changed Figure 14 as previous thermal values have been updated .................................................................................... 8 Changes from Revision G (April 2013) to Revision H * 2 Page Changed layout of National Semiconductor data sheet to TI format...................................................................................... 1 Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM2991 LM2991 www.ti.com SNVS099I - MAY 1999 - REVISED OCTOBER 2016 5 Pin Configuration and Functions KC and NDH Packages 5-Pin TO-220 Top View KTT Package 5-Pin DDPAK/TO-263 Top View 5 OUT Input 4 GND 3 IN Tab is input 5 OUT 4 GND 2 ON/OFF 3 IN 1 ADJ 2 ON/OFF 1 ADJ Pin Functions PIN NO. NAME I/O DESCRIPTION 1 ADJ I Feedback pin to the control loop for programming the output voltage. 2 ON/OFF I Logic high enable input 3 IN I Negative Input voltage. Internally connected directly to the thermal tab. 4 GND -- Ground 5 OUT O Regulated output voltage I Negative Input voltage. Internally connected directly to the device pin 3. The thermal tab must be connected to a copper area on the PCB at the same potential as device pin 3 (IN) to assure thermal performance, or leave the thermal tab floating. Do NOT connect the thermal tab to any potential other than the same potential at device pin 3. Do NOT connect the thermal tab to ground. -- TAB Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM2991 3 LM2991 SNVS099I - MAY 1999 - REVISED OCTOBER 2016 www.ti.com 6 Specifications 6.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (1) (2) Input voltage Power dissipation (2) (3) MAX UNIT -26 0.3 V (3) Internally limited Storage temperature, Tstg (1) MIN -65 150 C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. If Military/Aerospace specified devices are required, contact the Texas Instruments Sales Office/Distributors for availability and specifications. The maximum power dissipation is a function of TJ(MAX), RJA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) - TA)/RJA. If this dissipation is exceeded, the die temperature will rise above 125C, and the LM2991 will eventually go into thermal shutdown at a TJ of approximately 160C. Refer to Thermal Shutdown for more details. 6.2 ESD Ratings V(ESD) (1) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) VALUE UNIT 2000 V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. 6.3 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) (1) MIN Junction temperature, TJ ON/OFF pin Maximum input voltage (operational) (1) MAX UNIT -40 NOM 125 C 0 5 V -26 V Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 6.4 Thermal Information LM2991 THERMAL METRIC (1) TO-263 (KTT) TO-220 (NDH) (2) TO-220 (KC) (2) 5 PINS 5 PINS 5 PINS UNIT RJA (3) Junction-to-ambient thermal resistance, High-K 27.8 54.4 56.4 C/W RJC(top) Junction-to-case (top) thermal resistance 41.4 30.1 40.0 C/W RJB Junction-to-board thermal resistance 10.9 33.2 38.6 C/W JT Junction-to-top characterization parameter 6.0 11.6 12.8 C/W JB Junction-to-board characterization parameter 10.6 36.2 35.3 C/W RJC(bot) Junction-to-case (bottom) thermal resistance 0.7 0.5 0.6 C/W (1) (2) (3) 4 For more information about traditional and new thermal metrics, see Semiconductor and IC Package Thermal Metrics. The TO-220 package is vertically mounted in center of a JEDEC High-K test board (JESD 51-7) with no additional heat sink attached. This is a through-hole package; this is NOT a surface-mount package. Thermal resistance value RJA is based on the EIA/JEDEC High-K printed circuit board defined by JESD51-7 - High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages. Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM2991 LM2991 www.ti.com SNVS099I - MAY 1999 - REVISED OCTOBER 2016 6.5 Electrical Characteristics VIN = -10 V, VOUT = -3 V, IOUT = 1 A, COUT = 47 F, R1 = 2.7 k, TJ = 25C, unless otherwise specified. PARAMETER 5 mA IOUT 1 A Reference voltage Output voltage (VOUT) MIN TYP (1) MAX -1.234 -1.210 -1.186 V -1.15 V -3 V TEST CONDITIONS 5 mA IOUT 1 A, VOUT - 1 V VIN > -26 V -40C TJ 125C -1.27 -2 VIN = -26 V -24 Line regulation IOUT = 5 mA, VOUT -1 V > VIN > -26 V Load regulation 50 mA IOUT 1 A IOUT = 0.1 A, VOUT 100 mV Dropout voltage -25 0.04 0.04% 0.4% 0.1 0.2 IOUT = 0.1 A, VOUT 100 mV -40C TJ 125C IOUT = 1 A, VOUT 100 mV 0.6 IOUT 1 A 0.8 0.7 IOUT = 1 A, -40C TJ 125C 5 Ripple rejection Vripple = 1 VRMS, ripple = 1 kHz, IOUT = 5 mA Output noise 10 Hz to 100 kHz, IOUT = 5 mA 200 VOUT: ON 1.2 16 50 V 50 mA mA 60 VOUT: ON -40C TJ 125C dB 450 V V 0.8 VOUT: OFF 1.3 VOUT: OFF, -40C TJ 125C V 2.4 VON/OFF = 0.8 V, VOUT: ON 0.1 10 VON/OFF = 2.4 V, VOUT: OFF 40 100 60 250 Output leakage current VIN = -26 V, VON/OFF = 2.4 V, VOUT = 0 V Current limit VOUT = 0 V (1) V 1 VIN = VOUT, IOUT 1 A ON/OFF input current %/V 0.3 Dropout quiescent current ON/OFF input voltage V 0.004 IOUT = 1 A, VOUT 100 mV -40C TJ 125C Quiescent current UNIT 1.5 A A 2 A Typicals are at TJ = 25C and represent the most likely parametric norm. Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM2991 5 LM2991 SNVS099I - MAY 1999 - REVISED OCTOBER 2016 www.ti.com 6.6 Typical Characteristics 6 Figure 1. Dropout Voltage Figure 2. Normalized Output Voltage Figure 3. Output Voltage Figure 4. Output Noise Voltage Figure 5. Quiescent Current Figure 6. Maximum Output Current Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM2991 LM2991 www.ti.com SNVS099I - MAY 1999 - REVISED OCTOBER 2016 Typical Characteristics (continued) Figure 7. Maximum Output Current Figure 8. Ripple Rejection Figure 9. Output Impedance Figure 10. ON/OFF Control Voltage Figure 12. Low Voltage Behavior Figure 11. Adjust Pin Current Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM2991 7 LM2991 SNVS099I - MAY 1999 - REVISED OCTOBER 2016 www.ti.com Typical Characteristics (continued) 5 4.5 Power Dissipation (W) 4 3.5 3 2.5 2 1.5 1 0.5 0 0 Figure 13. Maximum Power Dissipation (TO-220) 8 10 20 30 40 50 60 70 80 Ambient Temperature, TA (qC) 90 100 D001 Figure 14. Maximum Power Dissipation (DDPAK/TO-263) Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM2991 LM2991 www.ti.com SNVS099I - MAY 1999 - REVISED OCTOBER 2016 7 Detailed Description 7.1 Overview The LM2991 is a five-pin, low-dropout, 1-A negative adjustable voltage regulator and negative power supply, ideally suited for a dual-supply system when using together with LM2941 series. The device may also be used as an adjustable current-sink load. 7.2 Functional Block Diagram 7.3 Feature Description 7.3.1 ON/Off Pin The LM2991 regulator can be turned off by applying a TTL or CMOS level high signal to the ON/OFF pin. The impedance of the voltage source driving the ON/OFF pin must be low enough to source the ON/OFF pin input current to meet the OFF threshold voltage level, 100 A maximum at 2.4 V. If the ON/OFF function is not needed, connect the pin to GND. The ON/OFF pin should not be left floating, as this is not an ensured operating condition. See Figure 15. 7.3.2 Forcing The Output Positive Due to an internal clamp circuit, the LM2991 can withstand positive voltages on its output. If the voltage source pulling the output positive is DC, the current must be limited to 1.5 A. A current over 1.5 A fed back into the LM2991 could damage the device. The LM2991 output can also withstand fast positive voltage transients up to 26 V, without any current limiting of the source. However, if the transients have a duration of over 1 ms, the output should be clamped with a Schottky diode to ground. 7.3.3 Thermal Shutdown The LM2991 has an internally set thermal shutdown point of typically 160C, with approximately 10C of hysteresis. This thermal shutdown temperature point is outside the specified Recommended Operating Conditions range, above the Absolute Maximum Ratings, and is intended as a safety feature for momentary fault conditions only. Avoid continuous operation near the thermal shutdown temperature as it may have a negative affect on the life of the device. Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM2991 9 LM2991 SNVS099I - MAY 1999 - REVISED OCTOBER 2016 www.ti.com 7.4 Device Functional Modes 7.4.1 Operation with VOUT(TARGET) -5 V VIN > -26 V The device operates if the input voltage is within VOUT(TARGET) -5 V to -26 V range. At input voltages beyond the VIN requirement, the devices do not operate correctly, and output voltage may not reach target value. 10 Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM2991 LM2991 www.ti.com SNVS099I - MAY 1999 - REVISED OCTOBER 2016 8 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI's customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 8.1 Application Information The LM2991 is a 1-A negative adjustable voltage regulator with an operating VIN range of -6 V to -26 V, and a regulated VOUT having 5% accuracy with a maximum rated IOUT current of 1 A. Efficiency is defined by the ratio of output voltage to input voltage because the LM2991 is a linear voltage regulator. To achieve high efficiency, the dropout voltage (VIN - VOUT) must be as small as possible, thus requiring a very low dropout LDO. Successfully implementing an LDO in an application depends on the application requirements. If the requirements are simply input voltage and output voltage, compliance specifications (such as internal power dissipation or stability) must be verified to ensure a solid design. If timing, start-up, noise, PSRR, or any other transient specification is required, the design becomes more challenging. 8.2 Typical Application Figure 15. LM2991 Typical Application With Adjustable Current Sink 8.2.1 Design Requirements For this design example, use the parameters listed in Table 1 as the input parameters. Table 1. Design Parameters DESIGN PARAMETER DESIGN REQUIREMENT Input voltage -26 V to -5 V Output voltage -2 V to -25 V (typical) Output current up to 1 A Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM2991 11 LM2991 SNVS099I - MAY 1999 - REVISED OCTOBER 2016 www.ti.com 8.2.2 Detailed Design Procedure At 400-mA loading, the dropout of the LM2991 has 1-V maximum dropout over temperature, thus an -5 V headroom is sufficient for operation over both input and output voltage accuracy. The efficiency of the LM2991 in this configuration is VOUT / VIN = 50%. To achieve the smallest form factor, the TO-263 (KTT) package is selected. Select input and output capacitors in accordance with the External Capacitors section. Aluminum capacitances of 470 F for the input and 50-F capacitors for the output are selected. With an efficiency of 50% and a 400-mA maximum load, the internal power dissipation is 2000 mW, which corresponds to 82.5C junction temperature rise for the TO-263 package. With an 25C ambient temperature, the junction temperature is at 107.5C. 8.2.2.1 External Capacitors The LM2991 regulator requires an output capacitor to maintain stability. The capacitor must be at least 10-F aluminum electrolytic or 1-F solid tantalum. The equivalent series resistance (ESR) of the output capacitor must be less than 10 , or the zero added to the regulator frequency response by the ESR could reduce the phase margin, creating oscillations. An input capacitor, of at least 1-F solid tantalum or 10-F aluminum electrolytic, is also needed if the regulator is situated more than 6 inches from the input power supply filter. 8.2.2.1.1 Input Capacitor TI recommends a solid tantalum or ceramic capacitor whose value is at least 1 F, but an aluminum electrolytic ( 10 F) may be used. However, aluminum electrolytic types should not be used in applications where the ambient temperature can drop below 0C because their internal impedance increases significantly at cold temperatures. 8.2.2.1.2 Output Capacitor The output capacitor must meet the ESR limits shown in Figure 16, which means it must have an ESR between about 25 m and 10 . Figure 16. Output Capacitor ESR Range A solid tantalum (value 1 F) is the best choice for the output capacitor. An aluminum electrolytic ( 10 F) may be used if the ESR is in the stable range. It should be noted that the ESR of a typical aluminum electrolytic will increase by as much as 50x as the temperature is reduced from 25C down to -40C, while a tantalum exhibits an ESR increase of about 2x over the same range. For this and other reasons, aluminum electrolytics should not be used in applications where low operating temperatures occur. The lower stable ESR limit of 25 m means that ceramic capacitors can not be used directly on the output of an LDO. A ceramic ( 2.2 F) can be used on the output if some external resistance is placed in series with it (1 recommended). Dielectric types X7R or X5R must be used if the temperature range of the application varies more than 25 from ambient to assure the amount of capacitance is sufficient. 12 Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM2991 LM2991 www.ti.com SNVS099I - MAY 1999 - REVISED OCTOBER 2016 8.2.2.2 Ceramic Bypass Capacitors Many designers place distributed ceramic capacitors whose value is in the range of 1000 pF to 0.1 F at the power input pins of the IC's across a circuit board. These can cause reduced phase margin or oscillations in LDO regulators. The advent of multi-layer boards with dedicated power and ground planes has removed the trace inductance that (previously) provided the necessary "de-coupling" to shield the output of the LDO from the effects of bypass capacitors. Avoid these capacitors, if possible; if ceramic bypass capacitors are used, keep them as far away from the LDO output as is practical. 8.2.2.3 Minimum Load A minimum load current of 500 A is required for proper operation. The external resistor divider can provide the minimum load, with the resistor from the adjust pin to ground set to 2.4 k. 8.2.2.4 Setting The Output Voltage The output voltage of the LM2991 is set externally by a resistor divider using Equation 1: VOUT = VREF x (1 + R2/R1) - (IADJ x R2) where * VREF = -1.21 V (1) The output voltage can be programmed within the range of -3 V to -24 V, typically an even greater range of -2 V to -25 V. The adjust pin current is about 60 nA, causing a slight error in the output voltage. However, using resistors lower than 100 k makes the error due to the adjust pin current negligible. For example, neglecting the adjust pin current, and setting R2 to 100 k and VOUT to -5 V, results in an output voltage error of only 0.16%. 8.2.2.5 Power Dissipation Knowing the device power dissipation and proper sizing of the thermal plane connected to the thermal tab is critical to ensuring reliable operation. Device power dissipation depends on input voltage, output voltage, and load conditions and can be calculated with Equation 2. PD(MAX) = (VIN(MAX) - VOUT) x IOUT (2) Power dissipation can be minimized, and greater efficiency can be achieved, by using the lowest available voltage drop option that would still be greater than the dropout voltage (VDO). However, keep in mind that higher voltage drops result in better dynamic (that is, PSRR and transient) performance. Power dissipation and junction temperature are most often related by the junction-to-ambient thermal resistance (RJA) of the combined PCB and device package and the temperature of the ambient air (TA), according to Equation 3 or Equation 4: TJ(MAX) = TA(MAX) + (RJA x PD(MAX)) PD(MAX) = (TJ(MAX) - TA(MAX)) / RJA (3) (4) Unfortunately, this RJA is highly dependent on the heat-spreading capability of the particular PCB design, and therefore varies according to the total copper area, copper weight, and location of the planes. The RJA recorded in Thermal Information is determined by the specific EIA/JEDEC JESD51-7 standard for PCB and copperspreading area, and is to be used only as a relative measure of package thermal performance. For a welldesigned thermal layout, RJA is actually the sum of the package junction-to-case (bottom) thermal resistance (RJCbot) plus the thermal resistance contribution by the PCB copper area acting as a heat sink. Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM2991 13 LM2991 SNVS099I - MAY 1999 - REVISED OCTOBER 2016 www.ti.com 8.2.2.6 Estimating Junction Temperature The EIA/JEDEC standard recommends the use of psi () thermal characteristics to estimate the junction temperatures of surface mount devices on a typical PCB board application. These characteristics are not true thermal resistance values, but rather package specific thermal characteristics that offer practical and relative means of estimating junction temperatures. These psi metrics are determined to be significantly independent of copper-spreading area. The key thermal characteristics (JT and JB) are given in Thermal Information and are used in accordance with Equation 5 or Equation 6. TJ(MAX) = TTOP + (JT x PD(MAX)) where * * PD(MAX) is explained in Equation 4 TTOP is the temperature measured at the center-top of the device package. TJ(MAX) = TBOARD + (JB x PD(MAX)) (5) where * * PD(MAX) is explained in Equation 4 TBOARD is the PCB surface temperature measured 1-mm from the device package and centered on the package edge. (6) For more information about the thermal characteristics JT and JB, see Semiconductor and IC Package Thermal Metrics; for more information about measuring TTOP and TBOARD, see Using New Thermal Metrics; and for more information about the EIA/JEDEC JESD51 PCB used for validating RJA, see Thermal Characteristics of Linear and Logic Packages Using JEDEC PCB Designs. These application notes are available at www.ti.com.. 8.2.3 Application Curves Figure 17. Line Transient Response 14 Submit Documentation Feedback Figure 18. Load Transient Response Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM2991 LM2991 www.ti.com SNVS099I - MAY 1999 - REVISED OCTOBER 2016 8.2.4 Additional Application Circuits Figure 19. Fully Isolated Post-Switcher Regulator 9 Power Supply Recommendations The LM2991 is designed to operate from an input voltage supply range between -6 V and -26 V. The input voltage range must provide adequate headroom in order for the device to have a regulated output. This input supply must be well regulated. Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM2991 15 LM2991 SNVS099I - MAY 1999 - REVISED OCTOBER 2016 www.ti.com 10 Layout 10.1 Layout Guidelines The dynamic performance of the LM2991 is dependent on the layout of the PCB. PCB layout practices that are adequate for typical LDOs may degrade the PSRR, noise, or transient performance of the device. Best performance is achieved by placing CIN and COUT on the same side of the PCB as the LM2991, and as close as is practical to the package. The ground connections for CIN and COUT must be back to the LM2991 GND pin using as wide and short of a copper trace as is practical. Good PC layout practices must be used or instability can be induced because of ground loops and voltage drops. The input and output capacitors must be directly connected to the IN, OUT, and GND pins of the LM2991 using traces which do not have other currents flowing in them (Kelvin connect). The best way to do this is to lay out CIN and COUT near the device with short traces to the IN, OUT, and GND pins. The regulator ground pin must be connected to the external circuit ground so that the regulator and its capacitors have a single-point ground. Stability problems have been seen in applications where vias to an internal ground plane were used at the ground points of the LM2991 device and the input and output capacitors. This was caused by varying ground potentials at these nodes resulting from current flowing through the ground plane. Using a single point ground technique for the regulator and its capacitors fixed the problem. Because high current flows through the traces going into the IN pin and coming from the OUT pin, Kelvin connect the capacitor leads to these pins so there is no voltage drop in series with the input and output capacitors. 10.2 Layout Example Thermal Vias R1 ADJ ON/OFF IN GND OUT VIN 1 2 3 4 5 CIN R2 COUT VOUT ON/OFF GND GND Figure 20. LM2991 TO-263 Board Layout 16 Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM2991 LM2991 www.ti.com SNVS099I - MAY 1999 - REVISED OCTOBER 2016 11 Device and Documentation Support 11.1 Device Support 11.1.1 Device Nomenclature Dropout Voltage: The input-output voltage differential at which the circuit ceases to regulate against further reduction in input voltage. Measured when the output voltage has dropped 100 mV from the nominal value obtained at (VOUT + 5 V) input, dropout voltage is dependent upon load current and junction temperature. Input Voltage: The DC voltage applied to the input terminals with respect to ground. Input-Output Differential: The voltage difference between the unregulated input voltage and the regulated output voltage for which the regulator will operate. Line Regulation: The change in output voltage for a change in the input voltage. The measurement is made under conditions of low dissipation or by using pulse techniques such that the average chip temperature is not significantly affected. Load Regulation: The change in output voltage for a change in load current at constant chip temperature. Long Term Stability: Output voltage stability under accelerated life-test conditions after 1000 hours with maximum rated voltage and junction temperature. Output Noise Voltage: The rms AC voltage at the output, with constant load and no input ripple, measured over a specified frequency range. Quiescent Current: That part of the positive input current that does not contribute to the positive load current. The regulator ground lead current. Ripple Rejection: The ratio of the peak-to-peak input ripple voltage to the peak-to-peak output ripple voltage. Temperature Stability of VOUT: The percentage change in output voltage for a thermal variation from room temperature to either temperature extreme. 11.2 Related Documentation For additional information, see the following: * Semiconductor and IC Package Thermal Metrics * Using New Thermal Metrics * Thermal Characteristics of Linear and Logic Packages Using JEDEC PCB Designs 11.3 Receiving Notification of Documentation Updates To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper right corner, click on Alert me to register and receive a weekly digest of any product information that has changed. For change details, review the revision history included in any revised document. 11.4 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2ETM Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 11.5 Trademarks E2E is a trademark of Texas Instruments. Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM2991 17 LM2991 SNVS099I - MAY 1999 - REVISED OCTOBER 2016 www.ti.com 11.5 Trademarks (continued) All other trademarks are the property of their respective owners. 11.6 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 11.7 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 12 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. 18 Submit Documentation Feedback Copyright (c) 1999-2016, Texas Instruments Incorporated Product Folder Links: LM2991 PACKAGE OPTION ADDENDUM www.ti.com 25-Apr-2017 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LM2991S NRND DDPAK/ TO-263 KTT 5 45 TBD Call TI Call TI -40 to 125 LM2991S P+ LM2991S/NOPB ACTIVE DDPAK/ TO-263 KTT 5 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LM2991S P+ LM2991SX NRND DDPAK/ TO-263 KTT 5 500 TBD Call TI Call TI -40 to 125 LM2991S P+ LM2991SX/NOPB ACTIVE DDPAK/ TO-263 KTT 5 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LM2991S P+ LM2991T NRND TO-220 KC 5 45 TBD Call TI Call TI -40 to 125 LM2991T P+ LM2991T/LB03 NRND TO-220 NDH 5 45 TBD Call TI Call TI LM2991T P+ LM2991T/LF03 ACTIVE TO-220 NDH 5 45 Pb-Free (RoHS Exempt) CU SN Level-1-NA-UNLIM LM2991T P+ LM2991T/NOPB ACTIVE TO-220 KC 5 45 Pb-Free (RoHS Exempt) CU SN Level-1-NA-UNLIM -40 to 125 LM2991T P+ (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com (4) 25-Apr-2017 There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 29-Jul-2016 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) LM2991SX DDPAK/ TO-263 KTT 5 500 330.0 24.4 LM2991SX/NOPB DDPAK/ TO-263 KTT 5 500 330.0 24.4 Pack Materials-Page 1 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 10.75 14.85 5.0 16.0 24.0 Q2 10.75 14.85 5.0 16.0 24.0 Q2 PACKAGE MATERIALS INFORMATION www.ti.com 29-Jul-2016 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM2991SX DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0 LM2991SX/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0 Pack Materials-Page 2 PACKAGE OUTLINE KC0005A TO-220 - 16.51 mm max height SCALE 0.850 TO-220 4.83 4.06 10.67 9.65 3.05 2.54 B 1.40 1.14 A 6.86 5.69 3.71-3.96 8.89 6.86 (6.275) 12.88 10.08 OPTIONAL CHAMFER 16.51 MAX 2X (R1) OPTIONAL 9.25 7.67 C (4.25) PIN 1 ID (OPTIONAL) NOTE 3 14.73 12.29 1 5X 0.25 5 0.61 0.30 1.02 0.64 C A B 3.05 2.03 4X 1.7 6.8 1 5 4215009/A 01/2017 NOTES: 1. All controlling linear dimensions are in inches. Dimensions in brackets are in millimeters. Any dimension in brackets or parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Shape may vary per different assembly sites. www.ti.com EXAMPLE BOARD LAYOUT KC0005A TO-220 - 16.51 mm max height TO-220 4X (1.45) PKG 0.07 MAX ALL AROUND 0.07 MAX ALL AROUND METAL TYP (1.45) PKG (2) 4X (2) 1 (R0.05) TYP 5X ( 1.2) SOLDER MASK OPENING, TYP (1.7) TYP 5 FULL R TYP (6.8) LAND PATTERN NON-SOLDER MASK DEFINED SCALE:12X 4215009/A 01/2017 www.ti.com MECHANICAL DATA NDH0005D www.ti.com MECHANICAL DATA KTT0005B TS5B (Rev D) BOTTOM SIDE OF PACKAGE www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2017, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LM2991S LM2991S/NOPB LM2991SX LM2991SX/NOPB LM2991T LM2991T/LB03 LM2991T/LF03 LM2991T/NOPB LM2991 MWC LM2991 MD8