SG3525A Pulse Width Modulator Control Circuit The SG3525A pulse width modulator control circuit offers improved performance and lower external parts count when implemented for controlling all types of switching power supplies. The on-chip +5.1 V reference is trimmed to 1% and the error amplifier has an input common-mode voltage range that includes the reference voltage, thus eliminating the need for external divider resistors. A sync input to the oscillator enables multiple units to be slaved or a single unit to be synchronized to an external system clock. A wide range of deadtime can be programmed by a single resistor connected between the CT and Discharge pins. This device also features built-in soft-start circuitry, requiring only an external timing capacitor. A shutdown pin controls both the soft-start circuitry and the output stages, providing instantaneous turn off through the PWM latch with pulsed shutdown, as well as soft-start recycle with longer shutdown commands. The under voltage lockout inhibits the outputs and the changing of the soft-start capacitor when VCC is below nominal. The output stages are totem-pole design capable of sinking and sourcing in excess of 200 mA. The output stage of the SG3525A features NOR logic resulting in a low output for an off-state. http://onsemi.com MARKING DIAGRAMS 16 PDIP-16 N SUFFIX CASE 648 SG3525AN AWLYYWW 16 1 1 16 SOIC-16L DW SUFFIX CASE 751G 16 SG3525A AWLYYWW 1 1 Features * * * * * * * * * * A WL YY WW 8.0 V to 35 V Operation 5.1 V 1.0% Trimmed Reference 100 Hz to 400 kHz Oscillator Range Separate Oscillator Sync Pin Adjustable Deadtime Control Input Undervoltage Lockout Latching PWM to Prevent Multiple Pulses Pulse-by-Pulse Shutdown Dual Source/Sink Outputs: 400 mA Peak Pb-Free Packages are Available* = Assembly Location = Wafer Lot = Year = Work Week PIN CONNECTIONS Inv. Input 1 16 Vref Noninv. Input 2 15 VCC Sync 3 14 Output B OSC. Output 4 13 VC CT 5 12 Ground RT 6 11 Output A Discharge 7 10 Shutdown Soft-Start 8 9 Compensation (Top View) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 2 of this data sheet. *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. Semiconductor Components Industries, LLC, 2005 January, 2005 - Rev. 5 1 Publication Order Number: SG3525A/D SG3525A 16 Vref 15 Reference Regulator VCC 12 VC 13 To Internal Circuitry Under- Voltage Lockout Ground OSC Output NOR 4 3 Sync RT Output A Q 6 F/F Oscillator Q NOR 5 CT Discharge 14 Output B 7 R 9 Compensation 11 1 INV. Input 2 Noninv. Input - Error Amp + + - PWM - S Latch SG3525A Output Stage S 50A VREF 8 CSoft-Start 10 Shutdown 5.0k 5.0k Figure 1. Representative Block Diagram ORDERING INFORMATION Package Shipping SG3525AN PDIP-16 25 Units / Rail SG3525ANG PDIP-16 (Pb-Free) 25 Units / Rail SG3525ADW SOIC-16L 47 Units / Rail SG3525ADWG SOIC-16L (Pb-Free) 47 Units / Rail SG3525ADWR2 SOIC-16L 1000 Tape & Reel SG3525ADWR2G SOIC-16L (Pb-Free) 1000 Tape & Reel Device For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 2 SG3525A MAXIMUM RATINGS Symbol Value Unit Supply Voltage Rating VCC +40 Vdc Collector Supply Voltage VC +40 Vdc Logic Inputs -0.3 to +5.5 V Analog Inputs -0.3 to VCC V 500 mA 50 mA 5.0 mA Output Current, Source or Sink IO Reference Output Current Iref Oscillator Charging Current Power Dissipation TA = +25C (Note 1) TC = +25C (Note 2) PD mW 1000 2000 Thermal Resistance, Junction-to-Air RJA 100 C/W Thermal Resistance, Junction-to-Case RJC 60 C/W TJ +150 C Tstg -55 to +125 C TSolder +300 C Operating Junction Temperature Storage Temperature Range Lead Temperature (Soldering, 10 seconds) Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. 1. Derate at 10 mW/C for ambient temperatures above +50C. 2. Derate at 16 mW/C for case temperatures above +25C. RECOMMENDED OPERATING CONDITIONS Characteristics Symbol Min Max Unit Supply Voltage VCC 8.0 35 Vdc Collector Supply Voltage VC 4.5 35 Vdc Output Sink/Source Current (Steady State) (Peak) IO 0 0 100 400 mA Reference Load Current Iref 0 20 mA Oscillator Frequency Range fosc 0.1 400 kHz Oscillator Timing Resistor RT 2.0 150 k Oscillator Timing Capacitor CT 0.001 0.2 F Deadtime Resistor Range RD 0 500 Operating Ambient Temperature Range TA 0 +70 C APPLICATION INFORMATION Shutdown Options (See Block Diagram, page 2) latch is immediately set providing the fastest turn-off signal to the outputs; and a 150 A current sink begins to discharge the external soft-start capacitor. If the shutdown command is short, the PWM signal is terminated without significant discharge of the soft-start capacitor, thus, allowing, for example, a convenient implementation of pulse-by-pulse current limiting. Holding Pin 10 high for a longer duration, however, will ultimately discharge this external capacitor, recycling slow turn-on upon release. Pin 10 should not be left floating as noise pickup could conceivably interrupt normal operation. Since both the compensation and soft-start terminals (Pins 9 and 8) have current source pull-ups, either can readily accept a pull-down signal which only has to sink a maximum of 100 A to turn off the outputs. This is subject to the added requirement of discharging whatever external capacitance may be attached to these pins. An alternate approach is the use of the shutdown circuitry of Pin 10 which has been improved to enhance the available shutdown options. Activating this circuit by applying a positive signal on Pin 10 performs two functions: the PWM http://onsemi.com 3 SG3525A ELECTRICAL CHARACTERISTICS (VCC = +20 Vdc, TA = Tlow to Thigh [Note 3], unless otherwise noted.) Characteristics Symbol Min Typ Max Unit Reference Output Voltage (TJ = +25C) Vref 5.00 5.10 5.20 Vdc Line Regulation (+8.0 V VCC +35 V) Regline - 10 20 mV Load Regulation (0 mA IL 20 mA) Regload - 20 50 mV Temperature Stability Vref/T - 20 - mV Vref 4.95 - 5.25 Vdc Short Circuit Current (Vref = 0 V, TJ = +25C) ISC - 80 100 mA Output Noise Voltage (10 Hz f 10 kHz, TJ = +25C) Vn - 40 200 Vrms Long Term Stability (TJ = +125C) (Note 4) S - 20 50 mV/khr - 2.0 6.0 % REFERENCE SECTION Total Output Variation Includes Line and Load Regulation over Temperature OSCILLATOR SECTION (Note 5, unless otherwise noted.) Initial Accuracy (TJ = +25C) Frequency Stability with Voltage (+8.0 V VCC +35 V) fosc DVCC - 1.0 2.0 % Frequency Stability with Temperature fosc DT - 0.3 - % Minimum Frequency (RT = 150 k, CT = 0.2 F) fmin - 50 - Hz Maximum Frequency (RT = 2.0 k, CT = 1.0 nF) fmax 400 - - kHz Current Mirror (IRT = 2.0 mA) 1.7 2.0 2.2 mA Clock Amplitude 3.0 3.5 - V Clock Width (TJ = +25C) 0.3 0.5 1.0 s Sync Threshold 1.2 2.0 2.8 V - 1.0 2.5 mA Sync Input Current (Sync Voltage = +3.5 V) ERROR AMPLIFIER SECTION (VCM = +5.1 V) Input Offset Voltage VIO - 2.0 10 mV Input Bias Current IIB - 1.0 10 A Input Offset Current IIO - - 1.0 A DC Open Loop Gain (RL 10 M) AVOL 60 75 - dB Low Level Output Voltage VOL - 0.2 0.5 V High Level Output Voltage VOH 3.8 5.6 - V Common Mode Rejection Ratio (+1.5 V VCM +5.2 V) CMRR 60 75 - dB Power Supply Rejection Ratio (+8.0 V VCC +35 V) PSRR 50 60 - dB Minimum Duty Cycle DCmin - - 0 % Maximum Duty Cycle DCmax 45 49 - % Input Threshold, Zero Duty Cycle (Note 5) Vth 0.6 0.9 - V Input Threshold, Maximum Duty Cycle (Note 5) Vth - 3.3 3.6 V Input Bias Current IIB - 0.05 1.0 A PWM COMPARATOR SECTION 3. Tlow = 0 Thigh = +70C 4. Since long term stability cannot be measured on each device before shipment, this specification is an engineering estimate of average stability from lot to lot. 5. Tested at fosc = 40 kHz (RT = 3.6 k, CT = 0.01 F, RD = 0 ). http://onsemi.com 4 SG3525A ELECTRICAL CHARACTERISTICS (continued) Characteristics Symbol Min Typ Max Unit Soft-Start Current (Vshutdown = 0 V) 25 50 80 A Soft-Start Voltage (Vshutdown = 2.0 V) - 0.4 0.6 V Shutdown Input Current (Vshutdown = 2.5 V) - 0.4 1.0 mA - - 0.2 1.0 0.4 2.0 18 17 19 18 - - 7.0 8.0 V SOFT-START SECTION OUTPUT DRIVERS (Each Output, VCC = +20 V) Output Low Level (Isink = 20 mA) (Isink = 100 mA) VOL Output High Level (Isource = 20 mA) (Isource = 100 mA) VOH Under Voltage Lockout (V8 and V9 = High) VUL 6.0 V V IC(leak) - - 200 A Rise Time (CL = 1.0 nF, TJ = 25C) tr - 100 600 ns Fall Time (CL = 1.0 nF, TJ = 25C) tf - 50 300 ns Shutdown Delay (VDS = +3.0 V, CS = 0, TJ = +25C) tds - 0.2 0.5 s Supply Current (VCC = +35 V) ICC - 14 20 mA Collector Leakage, VC = +35 V (Note 6) 6. Applies to SG3525A only, due to polarity of output pulses. Vref 16 4 PWM ADJ. 13 Flip/ Flop 3 O s c i l l a t o r RT 6 Deadtime 1.5k 7 Ramp 0.009 100 5 Out A 11 A 1.0k, 1.0W (2) 14 B 0.001 0.1 VC 0.1 Sync 1.0k VCC 0.1 0.1 Clock 3.0k 15 Reference Regulator Out B Comp 10k 1 = VIO 2 = 1(+) 3 = 1(-) 1 2 - V/I Meter + 12 PWM GND 0.01 50A + 2 1 3 2 5.0F - 5.0k E/A 5.0k + 1 2 3 Softstart 8 1 3 1 2 3 9 10 Vref 2.0k DUT Shutdown Figure 2. Lab Test Fixture http://onsemi.com 5 SG3525A 200 R D , DEAD TIME RESISTOR () 500 RT, TIMING RESISTOR (k ) 100 50 * RD = 0 20 10 5 6 5.0 RD * RT 7 300 200 100 CT 2.0 0 2.0 5.0 10 20 50 100 200 500 1000 2000 5000 10,000 0.2 0.5 1.0 1 - 50 100 200 2 + 9 CP RZ RZ = 20 k 40 20 0 -20 1.0 10 100 1.0 k 10 k 100 k 1.0 M 4.0 3.5 2.5 2.0 1.5 Source Sat, (VC-VOH) 1.0 Sink Sat, (VOL) 0.5 0 0.01 10 M VCC = +20 V TJ = +25C 3.0 f, FREQUENCY (Hz) 0.02 0.03 0.05 0.07 0.1 0.2 0.3 0.5 0.7 1.0 IO, OUTPUT SOURCE OR SINK CURRENT (A) Figure 5. Error Amplifier Open Loop Frequency Response Figure 6. Output Saturation Characteristics 15 16 VCC Q5 Q1 Q8 7.4k Q6 5 3 Sync 7 Discharge Q2 Q3 Q3 6 12 GND 20 Figure 4. Oscillator Discharge Time versus RD 60 CT 10 Figure 3. Oscillator Charge Time versus RT 80 RT 5.0 DISCHARGE TIME (s) 100 Vref 2.0 CHARGE TIME (s) V sat , SATURATION VOLTAGE (V) A VOL, VOLTAGE GAIN (dB) 400 2.0k Q9 2.0k Ramp To PWM 14k Q11 Q10 25k 5.0pF Blanking Q14 To Output 400A Q4 23k Q7 1.0k 1.0k Q12 Q13 3.0k Inverting Q1 Input 1 Noninverting Input 2 200A 250 Q4 Q2 To PWM Comparator 100A 5.8V 30 9 Compensation 4 OSC Output Figure 7. Oscillator Schematic Figure 8. Error Amplifier Schematic http://onsemi.com 6 SG3525A 13 VCC VC Q7 Q5 Q9 Q10 Q4 5.0k Vref 11, 14 Q11 Output Q8 Q6 2.0k Q1 Q2 5.0k Clock 10k Q3 Q6 Omitted in SG3527A 10k F/F PWM Figure 9. Output Circuit (1/2 Circuit Shown) Q1 +Vsupply To Output Filter +Vsupply R1 R1 R2 VC A 13 VC A SG3525A 11 GND Q2 R3 In conventional push-pull bipolar designs, forward base drive is controlled by R1-R3. Rapid turn-off times for the power devices are achieved with speed-up capacitors C1 and C2. For single-ended supplies, the driver outputs are grounded. The VC terminal is switched to ground by the totem-pole source transistors on alternate oscillator cycles. Figure 10. Single-Ended Supply Figure 11. Push-Pull Configuration +Vsupply R1 Q1 11 Q1 14 C1 T1 T1 13 11 VC A SG3525A SG3525A GND B B 12 12 VC A T1 Q1 R2 C2 14 14 GND 13 11 SG3525A B +Vsupply C1 13 Q2 GND B 12 12 R1 T2 Q2 14 C2 R2 The low source impedance of the output drivers provides rapid charging of power FET input capacitance while minimizing external components. Low power transformers can be driven directly by the SG3525A. Automatic reset occurs during deadtime, when both ends of the primary winding are switched to ground. Figure 12. Driving Power FETS Figure 13. Driving Transformers in a Half-Bridge Configuration http://onsemi.com 7 SG3525A PACKAGE DIMENSIONS PDIP-16 N SUFFIX CASE 648-08 ISSUE T NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. -A- 16 9 1 8 B F C L S -T- SEATING PLANE K H G D M J 16 PL 0.25 (0.010) M T A M http://onsemi.com 8 DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0 10 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0 10 0.51 1.01 SG3525A PACKAGE DIMENSIONS SOIC-16L DW SUFFIX CASE 751G-03 ISSUE C A D 9 h X 45 E 0.25 1 16X M 14X e T A S B S L A 0.25 B B NOTES: 1. DIMENSIONS ARE IN MILLIMETERS. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 3. DIMENSIONS D AND E DO NOT INLCUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.13 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION. MILLIMETERS DIM MIN MAX A 2.35 2.65 A1 0.10 0.25 B 0.35 0.49 C 0.23 0.32 D 10.15 10.45 E 7.40 7.60 e 1.27 BSC H 10.05 10.55 h 0.25 0.75 L 0.50 0.90 q 0 7 8 A1 H 8X M B M 16 SEATING PLANE T C http://onsemi.com 9 SG3525A ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 61312, Phoenix, Arizona 85082-1312 USA Phone: 480-829-7710 or 800-344-3860 Toll Free USA/Canada Fax: 480-829-7709 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder Japan: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Phone: 81-3-5773-3850 http://onsemi.com 10 For additional information, please contact your local Sales Representative. SG3525A/D