AT25SL321 32-Mbit, 1.7V Minimum SPI Serial Flash Memory with Dual I/O, Quad I/O and QPI Support Features Single 1.7V - 2.0V Supply Serial Peripheral Interface (SPI) and Quad Peripheral Interface (QPI) Compatible Supports SPI Modes 0 and 3 Supports Dual Output Read and Quad I/O Program and Read Supports QPI Program and Read 104 MHz* Maximum Operating Frequency Clock-to-Output (tV1) of 6 ns Up tp 65MB/S continuous data transfer rate Full Chip Erase Flexible, Optimized Erase Architecture for Code and Data Storage Applications 0.6 ms Typical Page Program (256 Bytes) Time 60 ms Typical 4-Kbyte Block Erase Time 200 ms Typical 32-Kbyte Block Erase Time 300 ms Typical 64-Kbyte Block Erase Time Hardware Controlled Locking of Protected Blocks via WP Pin 4K-bit secured One-Time Programmable Security Register Hardware Write Protection Serial Flash Discoverable Parameters (SFDP) Register Flexible Programming Byte/Page Program (1 to 256 Bytes) Dual or Quad Input Byte/Page Program (1 to 256 Bytes) Accelerated programming mode via 9V ACC pin Erase/Program Suspend and Resume JEDEC Standard Manufacturer and Device ID Read Methodology Low Power Dissipation 2A Deep Power-Down Current (Typical) 10A Standby current (Typical) 5mA Active Read Current (Typical) Endurance: 100,000 program/erase cycles (4KB, 32KB or 64KB blocks) Data Retention: 20 Years Industrial Temperature Range: -40C to +85C Industry Standard Green (Pb/Halide-free/RoHS Compliant) Package Options 8-lead SOIC (208-mil) 8-pad DFN (6 x 5 x 0.6 mm) 24-ball Ball Grid Array (BGA) 8 and 10-ball WLCSP, die Ball Grid Array (dBGA) 8-pad USON(3 x 4 x 0.55mm) Die in Wafer Form DS-25SL321-112F-3/2017 1. Introduction The Adesto(R) AT25SL321 is a serial interface Flash memory device designed for use in a wide variety of high-volume consumer based applications in which program code is shadowed from Flash memory into embedded or external RAM for execution. The flexible erase architecture of the AT25SL321 is ideal for data storage as well, eliminating the need for additional data storage devices. The erase block sizes of the AT25SL321 have been optimized to meet the needs of today's code and data storage applications. By optimizing the size of the erase blocks, the memory space can be used much more efficiently. Because certain code modules and data storage segments must reside by themselves in their own erase regions, the wasted and unused memory space that occurs with large block erase Flash memory devices can be greatly reduced. This increased memory space efficiency allows additional code routines and data storage segments to be added while still maintaining the same overall device density. SPI clock frequencies of up to 104MHz* are supported allowing equivalent clock rates of 266MHz for Dual Output and 532MHz for Quad Output when using the QPI and Fast Read Dual/Quad I/O instructions.The AT25SL321 array is organized into 65,536 programmable pages of 256-bytes each. Up to 256 bytes can be programmed at a time using the Page Program instructions. Pages can be erased 4KB Block, 32KB Block, 64KB Block or the entire chip. The devices operate on a single 1.7V to 1.95V power supply with current consumption as low as 5mA active and 2A for Deep Power Down. All devices offered in space-saving packages. The device supports JEDEC standard manufacturer and device identification with a 4K-bit Secured OTP. *Contact Adesto for availability of 133MHz operating frequency. AT25SL321 DS-25SL321-112F-3/2017 2 2. Pinouts and Pin Descriptions The following figures show the available package types. Figure 1-1. 8-SOIC (Top View) CS (IO1) (IO2) GND 1 2 3 4 8 7 6 5 VCC HOLD OR RESET (IO3) SCK SI (IO0) Figure 1-3. 24-dBGA (Top View) Figure 1-2. 8-UDFN (Top View) CS SO (IO1) WP (IO2) GND 1 8 2 7 3 6 4 5 VCC HOLD (IO3) SCK SI (IO0) Figure 1-4. 8-WLCSP (Bottom View) CS Vcc I/O1(SO) I/O3(HOLD) I/O2(WP) GND Figure 1-5. 10-WLCSP (Bottom View) Vcc GND I/O1(SO) I/O3(HOLD) I/O0(SI) I/O2(WP) SCK I/O0(SI) Figure 1-6. 8-pad USON (Bottom View) GND CS SCK SI (IO0) WP (IO2) SCK SO (IO1) HOLD (IO3) CS VCC *Final package outline drawing to be confirmed. AT25SL321 DS-25SL321-112F-3/2017 3 During all operations, VCC must be held stable and within the specified valid range: VCC (min) to VCC (max). All of the input and output signals must be held high or low (according to voltages of VIH, VOH, VIL or VOL. Table 1-1. Symbol Pin Descriptions Name and Function Asserted State Type Low Input - Input - Input/Output - Input/Output CHIP SELECT CS When this input signal is high, the device is deselected and serial data output pins are at high impedance. Unless an internal program, erase or write status register cycle is in progress, the device will be in the standby power mode (this is not the deep power down mode). Driving Chip Select (CS) low enables the device, placing it in the active power mode. After power-up, a falling edge on Chip Select (CS) is required prior to the start of any instruction. SERIAL CLOCK SCK This input signal provides the timing for the serial interface. Instructions, addresses, or data present at serial data input are latched on the rising edge of Serial Clock (SCK). Data are shifted out on the falling edge of the Serial Clock (SCK). SERIAL INPUT The SI pin is used to shift data into the device. The SI pin is used for all data input including command and address sequences. Data on the SI pin is always latched in on the rising edge of SCK. SI (I/O0) With the Dual-Output and Quad-Output Read commands, the SI Pin becomes an output pin (I/O0) in conjunction with other pins to allow two or four bits of data on (I/O3-0) to be clocked in on every falling edge of SCK To maintain consistency with the SPI nomenclature, the SI (I/O0) pin is referenced as the SI pin unless specifically addressing the Dual-I/O and Quad-I/O modes in which case it is referenced as I/O0. Data present on the SI pin is ignored whenever the device is deselected (CS is deasserted). SERIAL OUTPUT The SO pin is used to shift data out from the device. Data on the SO pin is always clocked out on the falling edge of SCK. SO (I/O1) With the Dual-Output Read commands, the SO Pin remains an output pin (I/O0) in conjunction with other pins to allow two bits of data on (I/O1-0) to be clocked in on every falling edge of SCK To maintain consistency with the SPI nomenclature, the SO (I/O1) pin is referenced as the SO pin unless specifically addressing the Dual-I/O modes in which case it is referenced as I/O1. The SO pin is in a high-impedance state whenever the device is deselected (CS is deasserted). AT25SL321 DS-25SL321-112F-3/2017 4 Table 1-1. Symbol Pin Descriptions (Continued) Name and Function Asserted State Type - Input/Output - Input/Output - Power - Power WRITE PROTECT WP (I/O2) The Write Protect (WP) pin can be used to protect the Status Register against data modification. The WP pin is active low. When the QE bit of Status Register-2 is set for Quad I/O, the WP pin (Hardware Write Protect) function is not available since this pin is used for IO2. See figures 1-1, 1-2, and 1-3 for the pin configuration of Quad I/O and QPI operation. ACCELERATED PROGRAMMING The device offers accelerated program operations through the ACC function. This function is primarily intended to allow faster manufacturing throughput at the factory. ACC If the system asserts VHH on this pin, the device uses the higher voltage on the pin to reduce the time required for program operations. Removing VHH from the ACC pin returns the device to normal operation. Note that the ACC pin must not be at VHH for operations other than accelerated programming, or device damage may result. In addition, the ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result. The ACC function is only available during standard SPI Mode. HOLD The HOLD pin is used to pause a serial sequence of the SPI flash memory without resetting the clocking sequence. To enable the HOLD mode, the CS must be in low state. The HOLD mode effects on with the falling edge of the HOLD signal with CLK being low. The HOLD mode ends on the rising edge of HOLD signal with SCK being low. HOLD (I/O3) In other words, HOLD mode can't be entered unless SCK is low at the falling edge of the HOLD signal. And HOLD mode can't be exited unless SCK is low at the rising edge of the HOLD signal. If CS is driven high during a HOLD condition, it resets the internal logic of the device. As long as HOLD signal is low, the memory remains in the HOLD condition. To re-work communication with the device, HOLD must go high, and CS must go low. See Figure 8.11 for HOLD timing. VCC GND DEVICE POWER SUPPLY: VCC is the supply voltage. It is the single voltage used for all device functions including read, program, and erase. The VCC pin is used to supply the source voltage to the device. Operations at invalid VCC voltages may produce spurious results and should not be attempted. GROUND: VSS is the reference for the VCC supply voltage. The ground reference for the power supply. GND should be connected to the system ground. AT25SL321 DS-25SL321-112F-3/2017 5 Block Diagram Figure 2-1 shows a block diagram of the AT25SL321 serial Flash. Figure 2-1. AT25SL321 Block Diagram Control and Protection Logic CS I/O Buffers and Latches SRAM Data Buffer SCK SI (I/O0) SO (I/O1) WP (I/O2) Interface Control And Logic Address Latch 2. Y-Decoder Y-Gating X-Decoder Flash Memory Array HOLD (I/O3) Note: I/O3-0 pin naming convention is used for Dual-I/O and Quad-I/O commands. AT25SL321 DS-25SL321-112F-3/2017 6 Memory Array To provide the greatest flexibility, the memory array of the AT25SL321 can be erased in four levels of granularity including a full chip erase. The size of the erase blocks is optimized for both code and data storage applications, allowing both code and data segments to reside in their own erase regions. The Memory Architecture Diagram illustrates the breakdown of each erase level. Figure 3-1. Memory Architecture Diagram Block Erase Detail 64KB 32KB Page Program Detail 4KB 1-256 Byte Block Address Range Block 125 Sector 62 *** Block 124 Block 1 Sector 0 Block 0 - 3FF000h - 3FE000h - 3FD000h - 3FC000h - 3FB000h - 3FA000h - 3F9000h - 3F8000h - 3F7000h - 3F6000h - 3F5000h - 3F4000h - 3F3000h - 3F2000h - 3F1000h - 3F0000h - 3EF000h - 3EE000h - 3ED000h - 3EC000h - 3EB000h - 3EA000h - 3E9000h - 3E8000h - 3E7000h - 3E6000h - 3E5000h - 3E4000h - 3E3000h - 3E2000h - 3E1000h - 3E0000h 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 00FFFFh-00F000h 00EFFFh-00E000h 00DFFFh-00D000h 00CFFFh-00C000h 00BFFFh-00B000h 00AFFFh-00A000h 009FFFh-009000h 008FFFh-008000h 007FFFh-007000h 006FFFh-006000h 005FFFh-005000h 004FFFh-004000h 003FFFh-003000h 002FFFh-002000h 001FFFh-001000h 000FFFh-000000h 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 3FFFFFh - 3FFF00h 3FFEFFh - 3FFE00h 3FFDFFh - 3FFD00h 3FFCFFh - 3FFC00h 3FFBFFh - 3FFB00h 3FFAFFh - 3FFA00h 3FF9FFh - 3FF900h 3FF8FFh - 3FF800h 3FF7FFh - 3FF700h 3FF6FFh - 3FF600h 3FF5FFh - 3FF500h 3FF4FFh - 3FF400h 3FF3FFh - 3FF300h 3FF2FFh - 3FF200h 3FF1FFh - 3FF100h 3FF0FFh - 3FF000h 3FEFFFh - 3FEF00h 3FEEFFh - 3FEE00h 3FEDFFh - 3FED00h 3FECFFh - 3FEC00h 3FEBFFh - 3FEB00h 3FEAFFh - 3FEA00h 3FE9FFh - 3FE900h 3FE8FFh - 3FE800h *** Block 126 3FFFFFh 3FEFFFh 3FDFFFh 3FCFFFh 3FBFFFh 3FAFFFh 3F9FFFh 3F8FFFh 3F7FFFh 3F6FFFh 3F5FFFh 3F4FFFh 3F3FFFh 3F2FFFh 3F1FFFh 3F0FFFh 3EFFFFh 3EEFFFh 3EDFFFh 3ECFFFh 3EBFFFh 3EAFFFh 3E9FFFh 3E8FFFh 3E7FFFh 3E6FFFh 3E5FFFh 3E4FFFh 3E3FFFh 3E2FFFh 3E1FFFh 3E0FFFh Page Address Range *** Sector 63 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB 4KB *** Block 127 *** 3. 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 256 Bytes 0017FFh - 001700h 0016FFh - 001600h 0015FFh - 001500h 0014FFh - 001400h 0013FFh - 001300h 0013FFh - 001300h 0013FFh - 001300h 0012FFh - 001200h 0011FFh - 001100h 0010FFh - 001000h 000FFFh - 000F00h 000CFFh - 000C00h 000BFFh - 000B00h 000AFFh - 000A00h 0009FFh - 000900h 0008FFh - 000800h 0007FFh - 000700h 0006FFh - 000600h 0005FFh - 000500h 0004FFh - 000400h 0003FFh - 000300h 0002FFh - 000200h 0001FFh - 000100h 0000FFh - 000000h AT25SL321 DS-25SL321-112F-3/2017 7 4. Device Operation 4.1 Standard SPI Operation The AT25SL321 features a serial peripheral interface on four signals: Serial Clock (SCK). Chip Select (CS), Serial Data Input (SI) and Serial Data Output (SO). Standard SPI instructions use the SI input pin to serially write instructions, addresses or data to the device on the rising edge of SCK. The SO output pin is used to read data or status from the device on the falling edge of SCK. SPI bus operation Modes 0 (0, 0) and 3 (1, 1) are supported. The primary difference between Mode 0 and Mode 3 concerns the normal state of the SCK signal when the SPI bus master is in standby and data is not being transferred to the Serial Flash. For Mode 0 the SCK signal is normally low on the falling and rising edges of CS. For Mode 3 the SCK signal is normally high on the falling and rising edges of CS. 4.2 Dual SPI Operation The AT25SL321 supports Dual SPI operation. This instruction allows data to be transferred to or from the device at two times the rate of the standard SPI. The Dual Read instruction is ideal for quickly downloading code to RAM upon powerup (code-shadowing) or for executing non-speed- critical code directly from the SPI bus (XIP). When using Dual SPI instructions the SI and SO pins become bidirectional I/0 pins; IO0 and IO1. 4.3 Quad SPI Operation The AT25SL321 supports Quad SPI operation. This instruction allows data to be transferred to or from the device at four times the rate of the standard SPI. The Quad Read instruction offers a significant improvement in continuous and random access transfer rates allowing fast code- shadowing to RAM or execution directly from the SPI bus (XIP). When using Quad SPI instruction the SI and SO pins become bidirectional IO0 and IO1, and the WP and HOLD pins become IO2 and IO3 respectively. Quad SPI instructions require the non-volatile Quad Enable bit (QE) in Status Register-2 to be set. 4.4 QPI Operation The AT25SL321 supports Quad Peripheral Interface (QPI) operation when the device is switched from Standard/ Dual/ Quad SPI mode to QPI mode using the "Enable QPI (38h)" instruction. To enable QPI mode, the non-volatile Quad Enable bit (QE) in Status Register-2 is required to be set. When using QPI instructions, the SI and SO pins become bidirectional IO0 and IO1, and the WP and HOLD pins become IO2 and IO3 respectively. The typical SPI protocol requires that the bytelong instruction code being shifted into the device only via SI pin in eight serial clocks. The QPI mode utilizes all four IO pins to input the instruction code, thus only two serial clocks are required. This can significantly reduce the SPI instruction overhead and improve system performance in an XIP environment. Standard/ Dual/ Quad SPI mode and QPI mode are exclusive. Only one mode can be active at any given time, "Enable QPI" and "Disable QPI/ Disable QPI 2" instructions are used to switch between these two modes. Upon powerup or after software reset using "Reset (99h) instruction, the default state of the device is Standard/ Dual/ Quad SPI mode. AT25SL321 DS-25SL321-112F-3/2017 8 5. Write Protection To protect inadvertent writes by the possible noise, several means of protection are applied to the Flash memory. 5.1 Write Protect Features While Power-on reset, all operations are disabled and no instruction is recognized. An internal time delay of tPUW can protect the data against inadvertent changes while the power supply is outside the operating specification. This includes the Write Enable, Page program, Block Erase, Chip Erase, Write Security Register and the Write Status Register instructions. For data changes, Write Enable instruction must be issued to set the Write Enable Latch (WEL) bit to "0". Powerup, Completion of Write Disable, Write Status Register, Page program, Block Erase and Chip Erase are subjected to this condition. Write Protect (WP) pin can control to change the Status Register under hardware control. The Deep Power Down mode provides extra protection from unexpected data changes as all instructions are ignored under this status except for Release Deep Power Down instruction. AT25SL321 DS-25SL321-112F-3/2017 9 6. Status Register The Read Status Register instruction can be used to provide status on the availability of the Flash memory array, if the device is write enabled or disabled the state of write protection and the Quad SPI setting. The Write Status Register instruction can be used to configure the devices writes protection features and Quad SPI setting. Write access to the Status Register is controlled by in some cases of the WP pin. Table 6-1. S7 S6 S5 S4 S3 S2 S1 SRP0 (R) (R) (R) (R) (R) WEL BUSY Reserved Reserved Reserved Reserved Reserved Write Enable Latch Erase or Write in Progress Status Register Protect 0 (NonVolatile) Table 6-2. 6.1 Status Register-1 S0 Status Register-2 S15 S14 S13 S12 S11 S10 S9 S8 SUS (R) (R) (R) (R) (R) QE SRP1 Suspend Status Reserved Reserved Reserved Reserved Reserved Quad Enable (Non- Volatile) Register Protect 1 (Non- Volatile) Busy BUSY is a read only bit in the status register (S0) that is set to a 1 state when the device is executing a Page Program, Erase, Write Status Register or Write Security Register instruction. During this time the device will ignore further instruction except for the Read Status Register and Erase / Program Suspend instruction (see tW, tPP, tSE, tBE1, tBE2 and tCE in AC Characteristics). When the Program, Erase, Write Status Register or Write Security Register instruction has completed, the BUSY bit will be cleared to a 0 state indicating the device is ready for further instructions. 6.2 Write Enable Latch (WEL) Write Enable Latch (WEL) is a read only bit in the status register (S1) that is set to a 1 after executing a Write Enable instruction. The WEL status bit is cleared to a 0 when device is write disabled. A write disable state occurs upon power-up or after any of the following instructions: Write Disable, Page Program, Erase and Write Status Register. 6.3 Status Register Protect (SRP1, SRP0) The Status Register Protect bits (SRP1 and SRP0) are nonvolatile read/write bits in the status register (S8 and S7). The SRP bits control the method of write protection: software protection, hardware protection, power supply lockdown or one time programmable (OTP) protection. AT25SL321 DS-25SL321-112F-3/2017 10 SRP1 SRP0 WP Status Register Description 0 0 X Software WP pin no control. The register can be written to 0 1 0 Hardware When WP pin is low the Status Register locked and can not 1 Hardware Unprotected 0 1 1 0 X Power Supply 1 1 X One Time When WP pin is high the Status register is unlocked and can be written to after a Write Enable instruction, WEL=1 Status Register is protected and cannot be written to again until the next power down, powerup cycle(1) Status Register is permanently protected and cannot be written to. Note: 1. When SRP1, SRP0=(1,0), a power down, power-up cycle will change SRP1, SRP0 to(0,0) state. 6.4 Quad Enable (QE) The Quad Enable (QE) bit is a non-volatile read/write bit in the status register (S9) that allows Quad operation. When the QE bit is set to a 0 state (factory default) the WP pin and HOLD are enabled. When the QE pin is set to a 1 the Quad IO2 and IO3 pins are enabled. WARNING : The QE bit should never be set to a 1 during standard SPI or Dual SPI operation if the WP or HOLD pins are tied directly to the power supply or ground. 6.5 Erase/Program Suspend Status (SUS) The Suspend Status bit (SUS) is a read only bit in the status register (S15) that is set to 1 after executing an Erase/Program Suspend (75h) instruction. The SUS status bit is cleared to 0 by Erase/Program Resume (7Ah) instruction as well as a power down, powerup cycle. AT25SL321 DS-25SL321-112F-3/2017 11 7. Instructions The SPI instruction set of the AT25SL321 consists of thirty eight basic instructions and the QPI instruction set of the AT25SL321 consists of thirty one basic instructions that are fully controlled through the SPI bus (see Instruction Set table). Instructions are initiated with the falling edge of Chip Select (CS). The first byte of data clocked into the input pins (SI or IO [3:0]) provides the instruction code. Data on the SI input is sampled on the rising edge of clock with most significant bit (MSB) first. Instructions are completed with the rising edge of edge CS. Clock relative timing diagrams for each instruction are included in figures 8-1 through 8-66 All read instructions can be completed after any clocked bit. However, all instructions that Write, Program or Erase must complete on a byte (CS driven high after a full 8bit have been clocked) otherwise the instruction will be terminated. This feature further protects the device from inadvertent writes. Additionally, while the memory is being programmed or erased, or when the Status Register is being written, all instructions except for Read Register will be ignored until the program or erase cycle has completed. Table 7-1. Manufacturer and Device Identification ID code Instruction Manufacturer ID Adesto 1Fh 90h, 92h, 94h, 9Fh Device ID AT25SL321 15h 90h, 92h, 94h, ABh Memory Type ID SPI / QPI 42h 9Fh Capacity Type ID 32M 16h 9Fh 7.1 Instruction Set Tables Table 7-2. Instruction Set Table 1 (SPI instruction)(1) INSTRUCTION NAME (CLOCK NUMBER) Write Enable BYTE 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6 (0 - 7) (8 - 15) (16 23) (24 31) (32 39) (40 47) 06h Write Enable For Volatile 50h Write Disable 04h Read 05h (SR7-SR0)(2) 35h (SR15SR8)(2) 01h (SR7-SR0) 31h (SR15SR8) Read Data 03h A23A16 A15A8 A7-A0 (D7D0) Fast Read Data 0Bh A23A16 A15A8 A7-A0 dummy Page Program 02h A23A16 A15A8 A7-A0 (D7D0)(3) Enable QPI 38h Block Erase(4KB) 20h A23A16 A15A8 A7-A0 Block Erase(32KB) 52h A23A16 A15A8 A7-A0 Status Register1 Read Status Register2 Write (SR15SR8) Status Register1 Write Status Register2 (D7D0) AT25SL321 DS-25SL321-112F-3/2017 12 7.1 Instruction Set Tables Table 7-2. Instruction Set Table 1 (SPI instruction)(1) Block Erase(64KB) Chip Erase D8h A23A16 A15A8 dummy dummy A7-A0 60h/C7h Erase/Program 75h Suspend Erase/Program 7Ah Resume Deep Power Down B9h Release Deep power ABh dummy (ID7-ID0)(2) down/ Device ID(4) Read Manufacturer/ 90h 00h 00h 00h or 01h Device ID(4) Read JEDEC ID 9Fh Reset Enable 66h Reset 99h Enter Secured OTP B1h Exit Secured OTP C1h Read 2Bh (MID7MID0) (D7D0) (MID7 MID0) (DID7DID0) (D7D0) (SC7-SC0) (10) Security Register Write 2Fh Security Register Read Serial Flash 5Ah A23A16 A15A8 A7-A0 dummy (D7D0) Discovery Parameter Table 7-3. Instruction Set Table 2 (Dual SPI Instruction) INSTRUCTION (CLOCK NUMBER) (0 - 7) (8 - 15) (16 23) (24 31) (32 39) (40 47) Fast Read Dual Output 3Bh A23-A16 A15-A8 A7-A0 dummy (D7D0)(6) Fast Read Dual I/O BBh A23-A8(5) A7-A0, (D7D0, ...)(6) Read Dual Manufacturer/ Device ID(4) 92h Table 7-4. 0000h (00h, xxxx) or (01h, xxxx) (MID7MID0) (DID7DID0)(6) Instruction Set Table 3 (Quad SPI Instruction) INSTRUCTION (CLOCK NUMBER) (0 - 7) (8 - 15) Fast Read Quad Output 6Bh A23-A16 Fast Read Quad I/O EBh A23A0, M7M0(7) Quad Page Program 33h A23-A0 (D7D0, ...)(8) (16 23) A15-A8 (xxx, D7-D0,...)(9) (24 31) A7-A0 (32 39) dummy (40 47) (D7D0) (8) (D7D0, ...)(8) AT25SL321 DS-25SL321-112F-3/2017 13 Table 7-4. Instruction Set Table 3 (Quad SPI Instruction) Read Quad 94h (00_0000h, xx) or (00_0001h, xx) Manufacturer /Device ID(4) Word Read Quad I/O E7h A23A0, M7M0(7) Set Burst with Wrap 77h xxxxxx, W6 W4(7) Table 7-5. (xxxx, MID7MID0) (xxxx, DID7DID0)(9) (xx, D7D0..) (D7D0)(8) Instruction Set Table 4 (QPI instruction) INSTRUCTION (CLOCK NUMBER) BYTE 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6 BYTE 7 BYTE 8 BYTE 9 (0 , 1 ) (2 , 3) (4 , 5) (6 , 7) (8 , 9) (10 , 11) (12 , 13) (14 , 15) (16 , 17) Write Enable 06h Write Enable for Volatile 50h Write Disable 04h Read Status Register1 05h (SR7 SR0) (2) Read Status Register2 35h (SR15 SR8)(2) (5) Write Status Register-1 01h (SR7 SR0) Write Status Register2 31h (SR15 (SR15 SR8) SR8) >80MHz Fast Read Data >104MHz 0Bh A23A16 A15A8 A7-A0 dummy dummy (D7D0) A23A16 A15A8 A7-A0 dummy dummy dummy Page Program 02h A23A16 A15A8 A7-A0 Block Erase(4KB) 20h A23A16 A15A8 A7-A0 Block Erase(32KB) 52h A23A16 A15A8 A7-A0 Block Erase(64KB) D8h A23A16 A15A8 A7-A0 Chip Erase 60h/ C7h Erase/Program Suspend 75h Erase/Program Resume 7Ah Deep Power Down B9h Release Deep Power Down ABh Read Manufacturer/Device ID(4) 90h Read JEDEC ID (4) 9Fh Enter Security B1h Exit Security C1h 00h (MID7 MID0) Manufacturer 00h 00h or 01h (D7D0) Memory Type (D7D0) Capacity Type (D7D0) (D7D0)(3) (MID7 MID0) (DID7 DID0) AT25SL321 DS-25SL321-112F-3/2017 14 Table 7-5. Instruction Set Table 4 (QPI instruction) Read Security Register 2Bh (SC7SC0) (10) Write Security Register 2Fh >80MHz Fast Read Quad I/O >104MHz EBh Reset Enable 66h Reset 99h Disable QPI FFh Burst Read with Wrap >80MHz >104MHz 0Ch A23A16 A15A8 A7-A0 (M7-M0) dummy (D7D0) A23A16 A15A8 A7-A0 (M7 M0) dummy dummy A23A16 A15A8 A7-A0 dummy dummy (D7D0) A23A16 A15A8 A7-A0 dummy dummy dummy A15A8 A7-A0 (D7D0) Set Read Parameter C0h P7-P0 Quad Page Program 33h A23A16 Notes: 1. on the 2. 3. 4. 5. 6. 7. 7.2 (D7D0) (D7 D0) Data bytes are shifted with Most Significant Bit first. Byte fields with data in parenthesis "()" indicate data being read from the device IO pin. SR = status register, The Status Register contents and Device ID will repeat continuously until CS terminates the instruction. At least one byte of data input is required for Page Program, Quad Page Program and Program Security Register, up to 256 bytes of data input. If more than 256 bytes of data are sent to the device, the addressing will wrap to the beginning of the page and overwrite previously sent data. See Manufacturer and Device Identification table for Device ID information. Dual Input Address IO0 = A22, A20, A18, A16, A14, A12, A10, A8, A6, A4, A2, A0, M6, M4, M2, M0 IO1 = A23, A21, A19, A17, A15, A13, A11, A9, A7, A5, A3, A1, M7, M5, M3, M1 Dual Output data IO0 = (D6, D4, D2, D0) IO1 = (D7, D5, D3, D1) Quad Input Address Set Burst with Wrap Input IO0 = A20, A16, A12, A8, A4, A0, M4, M0 IO1 = A21, A17, A13, A9, A5, A1, M5, M1 IO2 = A22, A18, A14, A10, A6, A2, M6, M2 IO3 = A23, A19, A15, A11, A7, A3, M7, M3 8. Quad Input/ Output Data IO0 = (D4, D0...) IO1 = (D5, D1...) IO2 = (D6, D2...) IO3 = (D7, D3...) 9. Fast Read Quad I/O Data Output IO0 = (x, x, x, x, D4, D0...) IO1 = (x, x, x, x, D5, D1...) IO2 = (x, x, x, x, D6, D2...) IO3 = (x, x, x, x, D7, D3...) 10. SC = security register IO0 = x, x, x, x, x, x, W4, x IO1 = x, x, x, x, x, x, W5, x IO2 = x, x, x, x, x, x, W6, x IO3 = x, x, x, x, x, x, x x Write Enable (06h) Write Enable instruction is for setting the Write Enable Latch (WEL) bit in the Status Register. The WEL bit must be set prior to every Program, Erase and Write Status Register instruction. To enter the Write Enable instruction, CS goes low prior to the instruction "06h" into Data Input (SI) pin on the rising edge of SCK, and then driving CS high. AT25SL321 DS-25SL321-112F-3/2017 15 Figure 7-1. Write Enable Instruction for SPI Mode (left) and QPI Mode (right) 7.3 Write Enable for Volatile Status Register (50h) This gives more flexibility to change the system configuration and memory protection schemes quickly without waiting for the typical non-volatile bit write cycles or affecting the endurance of the Status Register non-volatile bits. To write the volatile values into the Status Register bits, the Write Enable for Volatile Status Register (50h) instruction must be issued prior to a Write Status Register (01h) instruction. Write Enable for Volatile Status Register instruction (Figure 7-2) will not set the Write Enable Latch (WEL) bit. Once Write Enable for Volatile Status Register is set, a Write Enable instruction should not have been issued prior to setting Write Status Register instruction (01h or 31h). When Write Enable for Volatile Status Register (50h) is set in QPI Mode, the SUS bit (S15) and Reserved bits (S13, S12, S11 and S10) of the Status Register-2 must be driven to high after Write Status Register instruction (01h). Once Read Status Register (05h or 31h) is issued, the read values of SUS bit (S15) and Reserved bits (S13, S12, S11 and S10) of the Status Register-2 are ignored. Figure 7-2. Write Enable for Volatile Status Register Instruction for SPI Mode (left) and QPI Mode (right) AT25SL321 DS-25SL321-112F-3/2017 16 7.4 Write Disable (04h) The Write Disable instruction is to reset the Write Enable Latch (WEL) bit in the Status Register. To enter the Write Disable instruction, CS goes low prior to the instruction "04h" into Data Input (SI) pin on the rising edge of SCK, and then driving CS high. WEL bit is automatically reset write- disable status of "0" after Powerup and upon completion of the every Program, Erase and Write Status Register instructions. Figure 7-3. Write Disable Instruction for SPI Mode (left) and QPI Mode (right) 7.5 Read Status Register-1 (05h) and Read Status Register-2 (35h) The Read Status Register instructions are to read the Status Register. The Read Status Register can be read at any time (even in program/erase/write Status Register and Write Security Register condition). It is recommended to check the BUSY bit before sending a new instruction when a Program, Erase, Write Status Register or Write Status Register operation is in progress. The instruction is entered by driving CS low and sending the instruction code "05h" for Status Register-1 or "35h" for Status Register-2 into the SI pin on the rising edge of SCK. The status register bits are then shifted out on the SO pin at the falling edge of SCK with most significant bit (MSB) first as shown in (Figure 7-4 and Figure 7-5). The Status Register can be read continuously. The instruction is completed by driving CS high. Figure 7-4. Read Status Register Instruction (SPI Mode) AT25SL321 DS-25SL321-112F-3/2017 17 Figure 7-5. Read Status Register Instruction (QPI Mode) 7.6 Write Status Register (01h) The Write Status Register instruction is to write only non-volatile Status Register-1 bits (SRP0) and Status Register2 bits (QE and SRP1). All other Status Register bit locations are read-only and will not be affected by the Write Status Register instruction. A Write Enable instruction must previously have been issued prior to setting Write Status Register Instruction (Status Register bit WEL must equal 1). Once write is enabled, the instruction is entered by driving CS low, sending the instruction code, and then writing the status register data byte as illustrated in Figure 7-6 and Figure 7-7. The CS pin must be driven high after the eighth or sixteenth bit of data that is clocked in. If this is not done the Write Status Register instruction will not be executed. If CS is driven high after the eighth clock, the CMP QE and SRP1 bits will be cleared to 0. After CS is driven high, the self- timed Write Status Register cycle will commence for a time duration of tw (See AC Characteristics). While the Write Status Register cycle is in progress, the Read Status Register instruction may still be accessed to check the status of the BUSY bit. The BUSY bit is a 1 during the Write Status Register cycle and a 0 when the cycle is finished and ready to accept other instructions again. When the BUSY bit is asserted, the Write Enable Latch (WEL) bit in Status Register will be cleared to 0. Figure 7-6. Write Status Register Instruction (SPI Mode) AT25SL321 DS-25SL321-112F-3/2017 18 Figure 7-7. Write Status Register Instruction (QPI Mode) 7.7 Write Status Register-2 (31h) The Write Status Register-2 instruction is to write only non-volatile Status Register-2 bits (CMP, QE and SRP1). A Write Enable instruction must previously have been issued prior to setting Write Status Register Instruction (Status Register bit WEL must equal 1). Once write is enabled, the instruction is entered by driving CS low, sending the instruction code, and then writing the status register data byte as illustrated in Figure 7-8 and Figure 7-9. Using Write Status Register-2 (31h) instruction, software can individually access each onebyte status registers via different instructions. Figure 7-8. Write Status Register-2 Instruction (SPI Mode) AT25SL321 DS-25SL321-112F-3/2017 19 Figure 7-9. Write Status Register-2 Instruction (QPI Mode) 7.8 Read Data (03h) The Read Data instruction is to read data out from the device. The instruction is initiated by driving the CS pin low and then sending the instruction code "03h" with following a 24bit address (A23- A0) into the SI pin. After the address is received, the data byte of the addressed memory location will be shifted out on the SO pin at the falling edge of SCK with most significant bit (MSB) first. The address is automatically incremented to the next higher address after byte of data is shifted out allowing for a continuous stream of data. This means that the entire memory can be accessed with a single instruction as long as the clock continues. The instruction is completed by driving CS high. The Read Data instruction sequence is shown in Figure 7-10. If a Read Data instruction is issued while an Erase, Program or Write Status Register cycle is in process (BUSY=1) the instruction is ignored and will not have any effects on the current cycle. The Read Data instruction allows clock rates from D.C to a maximum of fR (see AC Electrical Characteristics). Figure 7-10. Read Data Instruction 7.9 Fast Read (0Bh) The Fast Read instruction is high speed reading mode that it can operate at the highest possible frequency of FR. The address is latched on the rising edge of the SCK. After the 24bit address, this is accomplished by adding "dummy" clocks as shown in Figure 7-11. The dummy clocks means the internal circuits require time to set up the initial address. During the dummy clocks, the data value on the SO pin is a "don't care". Data of each bit shifts out on the falling edge of SCK. AT25SL321 DS-25SL321-112F-3/2017 20 Figure 7-11. Fast Read Instruction (SPI Mode) 7.10 Fast Read in QPI Mode When QPI mode is enabled, the number of dummy clock is configured by the "Set Read Parameters (C0h)" instruction to accommodate wide range applications with different needs for either maximum Fast Read frequency or minimum data access latency. Depending on the Read Parameter Bit P[4] and P[5] setting, the number of dummy clocks can be configured as either 4, or 6 or 8. The default number of dummy clocks upon power up or after a Reset instruction is 4. (Please refer to Figure 7-12, Figure 7-13 and Figure 7-13). Figure 7-12. Fast Read instruction (QPI Mode, 80MHz) AT25SL321 DS-25SL321-112F-3/2017 21 Figure 7-13. Fast Read instruction (QPI Mode, 104MHz) 7.11 Fast Read Dual Output (3Bh) By using two pins (IO0 and IO1, instead of just IO0), The Fast Read Dual Output instruction allows data to be transferred from the AT25SL321 at twice the rate of standard SPI devices. The Fast Read Dual Output instruction is ideal for quickly downloading code from Flash to RAM upon power-up or for application that cache code-segments to RAM for execution. The Fast Read Dual Output instruction can operate at the highest possible frequency of F R (see AC Electrical Characteristics). After the 24bit address, this is accomplished by adding eight "dummy" clocks as shown in Figure 7-14. The dummy clocks allow the internal circuits additional time for setting up the initial address. During the dummy clocks, the data value on the SO pin is a "don't care". However, the IO0 pin should be highimpedance prior to the falling edge of the first data out clock. Figure 7-14. Fast Read Dual Output instruction (SPI Mode) AT25SL321 DS-25SL321-112F-3/2017 22 7.12 Fast Read Quad Output (6Bh) By using four pins (IO0, IO1, IO2, and IO3), The Fast Read Quad Output instruction allows data to be transferred from the AT25SL321 at four times the rate of standard SPI devices. A Quad enable of Status Register-2 must be executed before the device will accept the Fast Read Quad Output instruction (Status Register bit QE must equal 1). The Fast Read Quad Output instruction can operate at the highest possible frequency of F R (see AC Electrical Characteristics). This is accomplished by adding eight "dummy" clocks after the 24- bit address as shown in Figure 715. The dummy clocks allow the internal circuits additional time for setting up the initial address. During the dummy clocks, the data value on the SO pin is a "don't care". However, the IO0 pin should be highimpedance prior to the falling edge of the first data out clock. Figure 7-15. Fast Read Quad Output instruction (SPI Mode) 7.13 Fast Read Dual I/O (BBh) The Fast Read Dual I/O instruction reduces cycle overhead through double access using two IO pins: IO0 and IO1. Continuous read mode The Fast Read Dual I/O instruction can further reduce cycle overhead through setting the Mode bits (M7-0) after the input Address bits (A23-0). The upper nibble of the Mode (M7-4) controls the length of the next Fast Read Dual I/O instruction through the inclusion or exclusion of the first byte instruction code. The lower nibble bits of the Mode (M3-0) are don't care ("X"), However, the IO pins should be high-impedance prior to the falling edge of the first data out clock. AT25SL321 DS-25SL321-112F-3/2017 23 If the Mode bits (M70) equal "Ax" hex, then the next Fast Dual I/O instruction (after CS is raised and then lowered) does not require the instruction (BBh) code, as shown in Figure 7-16 and Figure 7-17. This reduces the instruction sequence by eight clocks and allows the address to be immediately entered after CS is asserted low. If Mode bits (M70) are any value other "Ax" hex, the next instruction (after CS is raised and then lowered) requires the first byte instruction code, thus returning to normal operation. A Mode Bit Reset can be used to reset Mode Bits (M70) before issuing normal instructions. Figure 7-16. Fast Read Dual I/O Instruction (initial instruction or previous M70 Axh) AT25SL321 DS-25SL321-112F-3/2017 24 Figure 7-17. Fast Read Dual I/O Instruction (previous M70= Axh) 7.14 Fast Read Quad I/O (EBh) The Fast Read Quad I/O instruction reduces cycle overhead through quad access using four IO pins: IO0, IO1, IO2, and IO3. The Quad Enable bit (QE) of Status Register-2 must be set to enable the Fast read Quad I/O Instruction. Continuous read mode The Fast Read Quad I/O instruction can further reduce instruction overhead through setting the Mode bits (M7-0) with following the input Address bits (A23-0), as shown in Figure 7-18. The upper nibble of the Mode (M7-4) controls the length of the next Fast Read Quad I/O instruction through the inclusion or exclusion of the first byte instruction code. The lower nibble bits of the Mode (M3-0) are don't care ("X"). However, the IO pins should be high-impedance prior to the falling edge of the first data out clock. If the Mode bits (M70) equal "Ax" hex, then the next Fast Read Quad I/O instruction (after CS is raised and then lowered) does not require the EBh instruction code, as shown in Figure 7-19. This reduces the instruction sequence by eight clocks and allows the address to be immediately entered after CS is asserted low. If the Mode bits (M70) are any value other than "Ax" hex, the next instruction (after CS is raised and then lowered) requires the first byte instruction code, thus retuning normal operation. A Mode Bit Reset can be used to reset Mode Bits (M70) before issuing normal instructions. AT25SL321 DS-25SL321-112F-3/2017 25 Figure 7-18. Fast Read Quad I/O Instruction (Initial instruction or previous M70 Axh, SPI mode) Figure 7-19. Fast Read Quad I/O Instruction (previous M70 = Axh, SPI mode) Wrap Around in SPI mode The Fast Read Quad I/O instruction can also be used to access specific portion within a page by issuing a "Set Burst with Wrap" (77h) instruction prior Fast Read Quad I/O (EBh) instruction. The "Set Burst with Wrap" (77h) instruction can either enable or disable the "Wrap Around" feature for the following Fast Read Quad I/O instruction. When "Wrap Around" is enabled, the data being accessed can be limited to an 8/16/32/64-byte section of a 256-byte page. The output data starts at the initial address specified in the instruction, once it reaches the ending boundary of the 8/16/32/64-byte section, the output will wrap around to the beginning boundary automatically until CS is pulled high to terminate the instruction. The Burst with Wrap feature allows applications that use cache to quickly fetch a critical address and then fill the cache afterwards within a fixed length (8/16/32/64-byte) of data without issuing multiple read instructions. (Please refer to Section 7.31 Set Burst with Wrap). AT25SL321 DS-25SL321-112F-3/2017 26 Fast Read Quad I/O in QPI mode When QPI mode in enabled, the number of dummy clocks is configured by the "Set Read Parameters (C0h)" instruction to accommodate a wide range applications with different needs for either maximum Fast Read frequency or minimum data access latency. Depending on the Read Parameter Bits P [4] and P [5] setting, the number of dummy clocks can be configured as either 4 or 6 or 8. The default number of dummy clocks upon power up or after a Reset (99h) instruction is 4. "Continuous Read Mode" feature is also available in QPI mode for Fast Read Quad I/O instruction. In QPI mode, the "Continuous Read Mode" bits M7-0 are also considered as dummy clocks. In the default setting, the data output will follow the Continuous Read Mode bits immediately. "Wrap Around" feature is not available in QPI mode for Fast Read Quad I/O instruction. To perform a read operation with fixed data length wrap around in QPI mode, a "Burst Read with Wrap" (0Ch) instruction must be used. (Please refer to Section 7.32 Burst Read with Wrap). Figure 7-20. Fast Read Quad I/O Instruction (Initial instruction or previous M70 Axh, QPI mode, 80MHz) Figure 7-21. Fast Read Quad I/O Instruction (Initial instruction or previous M70 Axh, QPI mode, 104MHz) AT25SL321 DS-25SL321-112F-3/2017 27 7.15 Page Program (02h) The Page Program instruction is for programming the memory to be "0". A Write Enable instruction must be issued before the device accept the Page Program Instruction (Status Register bit WEL=1). After the Write Enable (WREN) instruction has been decoded, the device sets the Write Enable Latch (WEL). The instruction is entered by driving the CS pin low and then sending the instruction code "02h" with following a 24-bits address (A23-A0) and at least one data byte, into the SI pin. The CS pin must be driven low for the entire time of the instruction while data is being sent to the device. (Please refer to Figure 7-22 and Figure 7-23). If an entire 256 byte page is to be programmed, the last address byte (the 8 least significant address bits) should be set to 0. If the last address byte is not zero, and the number of clocks exceeds the remaining page length, the addressing will wrap to the beginning of the page. In some cases, less than 256 bytes (a partial page) can be programmed without having any effect on other bytes within the same page. One condition to perform a partial page program is that the number of clocks cannot exceed the remaining page length. If more than 256 bytes are sent to the device the addressing will wrap to the beginning of the page and overwrite previously sent data The CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done the Page Program instruction will not be executed. After CS is driven high, the self-timed Page Program instruction will commence for a time duration of tPP (See AC Characteristics). While the Page Program cycle is in progress, the Read Status Register instruction may still be accessed for checking the status of the BUSY bit. The BUSY bit is a 1 during the Page Program cycle and becomes a 0 when the cycle is finished and the device is ready to accept other instructions again. When the BUSY bit is asserted, the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. Figure 7-22. Page Program Instruction (SPI Mode) AT25SL321 DS-25SL321-112F-3/2017 28 Figure 7-23. Page Program Instruction (QPI Mode) 7.16 Quad Page Program (33h) The Quad Page Program instruction is to program the memory as being "0" at previously erased memory areas. The Quad Page Program takes four pins: IO0, IO1, IO2 and IO3 as address and data input, which can improve programmer performance and the effectiveness of application of lower clock less than 5MHz. System using faster clock speed will not get more benefit for the Quad Page Program as the required internal page program time is far more than the time data clock-in. To use Quad Page Program, the Quad Enable bit must be set, A Write Enable instruction must be executed before the device will accept the Quad Page Program instruction (Status Register1, WEL=1). The instruction is initiated by driving the CS pin low then sending the instruction code "33h" with following a 24bit address (A23A0) and at least one data, into the IO pins. The CS pin must be held low for the entire length of the instruction while data is being sent to the device. All other functions of Quad Page Program are perfectly same as standard Page Program. (Please refer to Figure 724 and Figure 7-25). AT25SL321 DS-25SL321-112F-3/2017 29 Figure 7-24. Quad Page Program Instruction (SPI mode) Figure 7-25. Quad Page Program Instruction (QPI mode) AT25SL321 DS-25SL321-112F-3/2017 30 7.17 Block Erase (20h) The Block Erase instruction is to erase the data of the selected sector as being "1". The instruction is used for 4K-byte Block. Prior to the Block Erase Instruction, the Write Enable instruction must be issued. The instruction is initiated by driving the CS pin low and shifting the instruction code "20h" followed a 24-bit Block address (A23-A0). (Please refer to Figure 7-26 and Figure 7-27). The CS pin must go high after the eighth bit of the last byte has been latched in, otherwise, the Block Erase instruction will not be executed. After CS goes high, the self-timed Block Erase instruction will commence for a time duration of tSE (See AC Characteristics). While the Block Erase cycle is in progress, the Read Status Register instruction may still be accessed for checking the status of the BUSY bit. The BUSY bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is finished and the device is ready to accept other instructions again. When the BUSY bit is asserted, the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. Figure 7-26. Block Erase Instruction (SPI Mode) Figure 7-27. Block Erase Instruction (QPI Mode) AT25SL321 DS-25SL321-112F-3/2017 31 7.18 32KB Block Erase (52h) The Block Erase instruction is to erase the data of the selected block as being "1". The instruction is used for 32K-byte Block erase operation. Prior to the Block Erase Instruction, a Write Enable instruction must be issued. The instruction is initiated by driving the CS pin low and shifting the instruction code "52h" followed a 24-bit block address (A23-A0). (Please refer to Figure 7-28 and Figure 7-29). The CS pin must go high after the eighth bit of the last byte has been latched in, otherwise, the Block Erase instruction will not be executed. After CS is driven high, the self-timed Block Erase instruction will commence for a time duration of tBE1 (See AC Characteristics). While the Block Erase cycle is in progress, the Read Status Register instruction may still be read the status of the BUSY bit. The BUSY bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is finished and the device is ready to accept other instructions again. When the BUSY bit is asserted, the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. Figure 7-28. 32KB Block Erase Instruction (SPI Mode) Figure 7-29. 32KB Block Erase Instruction (QPI Mode) AT25SL321 DS-25SL321-112F-3/2017 32 7.19 64KB Block Erase (D8h) The Block Erase instruction is to erase the data of the selected block as being "1". The instruction is used for 64K-byte Block erase operation. Prior to the Block Erase Instruction, a Write Enable instruction must be issued. The instruction is initiated by driving the CS pin low and shifting the instruction code "D8h" followed a 24-bit block address (A23-A0). (Please refer to Figure 7-30 and Figure 7-31). The CS pin must go high after the eighth bit of the last byte has been latched in, otherwise, the Block Erase instruction will not be executed. After CS is driven high, the self-timed Block Erase instruction will commence for a time duration of tBE2 (See AC Characteristics). While the Block Erase cycle is in progress, the Read Status Register instruction may still be read the status of the BUSY bit. The BUSY bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is finished and the device is ready to accept other instructions again. When the BUSY bit is asserted, the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. Figure 7-30. 64KB Block Erase Instruction (SPI Mode) Figure 7-31. 64KB Block Erase Instruction (QPI Mode) AT25SL321 DS-25SL321-112F-3/2017 33 7.20 Chip Erase (C7h / 60h) The Chip Erase instruction clears all bits in the device to be FFh (all 1s). Prior to the Chip Erase Instruction, a Write Enable instruction must be issued. The instruction is initiated by driving the CS pin low and shifting the instruction code "C7h" or "60h". (Please refer to Figure 7-32). The CS pin must go high after the eighth bit of the last byte has been latched in, otherwise, the Chip Erase instruction will not be executed. After CS is driven high, the self-timed Chip Erase instruction will commence for a duration of tCE (See AC Characteristics). While the Chip Erase cycle is in progress, the Read Status Register instruction may still be accessed to check the status of the BUSY bit. The BUSY bit is a 1 during the Chip Erase cycle and becomes a 0 when the cycle is finished and the device is ready to accept other instructions again. When the BUSY bit is asserted, the Write Enable Latch (W EL) bit in the Status Register is cleared to 0. Figure 7-32. Chip Erase Instruction for SPI Mode (left) and QPI Mode (right) 7.21 Erase / Program Suspend (75h) The Erase/Program Suspend instruction allows the system to interrupt a Block Erase operation or a Page Program, Quad Data Input Page Program, Quad Page Program operation. Erase Suspend is valid only during the Block erase operation. The Write Status Register-1 (01h), Write Status Register2 (31h) instruction and Erase instructions (20h, 52h, D8h, C7h, 60h) are not allowed during Erase Suspend. During the Chip Erase operation, the Erase Suspend instruction is ignored. Program Suspend is valid only during the Page Program, Quad Data Input Page Program or Quad Page Program operation. The Write Status Register-1(01h), Write Status Register-2 (31h) instruction, Program instructions (02h and 33h) and Erase Instructions (20h, 52h, D8h, C7h, 60h) are not allowed during Program Suspend. The Erase/Program Suspend instruction "75h" will be accepted by the device only if the SUS bit in the Status Register equals to 0 and the BUSY bit equals to 1 while a Block Erase or a Page Program operation is on-going. If the SUS bit equals to 1 or the BUSY bit equals to 0, the Suspend instruction will be ignored by the device. A maximum of time of "tSUS" (See AC Characteristics) is required to suspend the erase or program operation. After Erase/Program Suspend, the SUS bit in the Status Register will be set from 0 to 1 immediately and The BUSY bit in the Status Register will be cleared from 1 to 0 within "tSUS". For a previously resumed Erase/Program operation, it is also required that the Suspend instruction "75h" is not issued earlier than a minimum of time of "tSUS" following the preceding Resume instruction "7Ah". AT25SL321 DS-25SL321-112F-3/2017 34 Unexpected power off during the Erase/Program suspend state will reset the device and release the suspend state. SUS bit in the Status Register will also reset to 0. The data within the page or block that was being suspended may become corrupted. It is recommended for the user to implement system design techniques against the accidental power interruption and preserve data integrity during erase/program suspend state. (Please refer to Figure 7-33 and Figure 7-34). Figure 7-33. Erase Suspend instruction (SPI Mode) Figure 7-34. Erase Suspend instruction (QPI Mode) 7.22 Erase / Program Resume (7Ah) The Erase/Program Resume instruction "7Ah" is to restart the Block Erase operation or the Page Program operation upon an Erase/Program Suspend. The Resume instruction "7Ah" will be accepted by the device only if the SUS bit in the Status Register equals to 1 and the BUSYbit equals to 0. After issued, the SUS bit will be cleared from 1 to 0 immediately, the BUSY bit will be set from 0 to 1 within 200ns and the Block will complete the erase operation or the page will complete the program operation. If the SUS bit equals to 0 or the BUSY bit equals to 1, the Resume instruction "7Ah" will be ignored by the device. AT25SL321 DS-25SL321-112F-3/2017 35 Resume instruction cannot be accepted if the previous Erase/Program Suspend operation was interrupted by unexpected power off. It is also required that a subsequent Erase/Program Suspend instruction not to be issued within a minimum of time of "tSUS" following a previous Resume instruction. (Please refer to Figure 7-35 and Figure 7-36). Figure 7-35. Erase / Program Resume instruction (SPI Mode) Figure 7-36. Erase / Program Resume instruction (QPI Mode) 7.23 Deep Power Down (B9h) Executing the Deep Power Down instruction is the best way to put the device in the lowest power consumption. The Deep Power Down instruction reduces the standby current (from ICC1 to ICC2, as specified in AC characteristics). The instruction is entered by driving the CS pin low with following the instruction code "B9h". (Please refer to Figure 7-37 and Figure 7-38). The CS pin must go high exactly at the byte boundary (the latest eighth bit of instruction code been latchedin); otherwise, the Deep Power Down instruction is not executed. After CS goes high, it requires a delay of tDP and the Deep Power Down mode is entered. While in the Release Deep Power Down / Device ID instruction, which restores the device to normal operation, will be recognized. All other instructions are ignored including the Read Status Register instruction, which is always available during normal operation. Deep Power Down Mode automatically stops at Power-Down, and the device always Powerup in the Standby Mode. AT25SL321 DS-25SL321-112F-3/2017 36 Figure 7-37. Deep Power Down Instruction (SPI Mode) Figure 7-38. Deep Power Down Instruction (QPI Mode) 7.24 Release Deep Power Down / Device ID (ABh) The Release Deep Power Down / Device ID instruction is a multi-purpose instruction. It can be used to release the device from the Deep Power Down state or obtain the device identification (ID). The instruction is issued by driving the CS pin low, sending the instruction code "ABh" and driving CS high as shown in figure Figure 7-39 and Figure 7-40. Release from Deep Power Down require the time duration of tRES1 (See AC Characteristics) for re-work a normal operation and accepting other instructions. The CS pin must keep high during the tRES1 time duration. The Device ID can be read during SPI mode only. In other words, Device ID feature is not available in QPI mode for Release Deep Power Down/Device ID instruction. To obtain the Device ID in SPI mode, instruction is initiated by driving the CS pin low and sending the instruction code "ABh" with following 3dummy bytes. The Device ID bits are then shifted on the falling edge of SCK with most significant bit (MSB) first as shown in Figure 7-41. After CS is driven high it must keep high for a time duration of tRES2 (See AC Characteristics). The Device ID can be read continuously. The instruction is completed by driving CS high. If the Release from Deep Power Down /Device ID instruction is issued while an Erase, Program or Write cycle is in process (when BUSY equals 1) the instruction is ignored and will not have any effects on the current cycle. AT25SL321 DS-25SL321-112F-3/2017 37 Figure 7-39. Release Power Down Instruction (SPI Mode) Figure 7-40. Release Power Down Instruction (QPI Mode) Figure 7-41. Release Power Down / Device ID Instruction (SPI Mode) AT25SL321 DS-25SL321-112F-3/2017 38 7.25 Read Manufacturer / Device ID Dual I/O (90h) The Read Manufacturer/ Device ID Dual I/O instruction provides both the JEDEC assigned manufacturer ID and the specific device ID. The Read Manufacturer/ Device ID instruction is very similar to the Fast Read Dual I/O instruction. The instruction is initiated by driving the CS pin low and shifting the instruction code "90h" followed by a 24bit address (A23-A0) of 000000h. After which, the Manufacturer ID for Adesto (1Fh) and the Device ID(15h) are shifted out on the falling edge of SCK with most significant bit (MSB) first as shown in Figure 7-42 and Figure 7-43. If the 24bit address is initially set to 000001h the Device ID will be read first and then followed by the Manufacturer ID. The Manufacturer and Device ID can be read continuously, alternating from one to the other. The instruction is completed by driving CS high. Figure 7-42. Read Manufacturer/ Device ID instruction (SPI Mode) AT25SL321 DS-25SL321-112F-3/2017 39 Figure 7-43. Read Manufacturer/ Device ID instruction (QPI Mode) 7.26 Read Manufacturer / Device ID Dual I/O (92h) The Read Manufacturer/ Device ID Dual I/O instruction provides both the JEDEC assigned manufacturer ID and the specific device ID. The Read Manufacturer/ Device ID instruction is very similar to the Fast Read Dual I/O instruction. The instruction is initiated by driving the CS pin low and shifting the instruction code "92h" followed by a 24bit address (A23-A0) of 000000h. After which, the Manufacturer ID for Adesto (1Fh) and the Device ID(15h) are shifted out on the falling edge of SCK with most significant bit (MSB) first as shown in Figure 7-44. If the 24bit address is initially set to 000001h the Device ID will be read first and then followed by the Manufacturer ID. The Manufacturer and Device ID can be read continuously, alternating from one to the other. The instruction is completed by driving CS high. Figure 7-44. Read Dual Manufacturer/ Device ID Dual I/O instruction (SPI Mode) AT25SL321 DS-25SL321-112F-3/2017 40 7.27 Read Manufacturer / Device ID Quad I/O (94h) The Read Manufacturer/ Device ID Quad I/O instruction provides both the JEDEC assigned manufacturer ID and the specific device ID. The Read Manufacturer/ Device ID instruction is very similar to the Fast Read Quad I/O instruction. The instruction is initiated by driving the CS pin low and shifting the instruction code "94h" followed by a 24bit address (A23-A0) of 000000h. After which, the Manufacturer ID for Adesto (1Fh) and the Device ID(15h) are shifted out on the falling edge of SCK with most significant bit (MSB) first as shown in Figure 7-45. If the 24bit address is initially set to 000001h the Device ID will be read first and then followed by the Manufacturer ID. The Manufacturer and Device ID can be read continuously, alternating from one to the other. The instruction is completed by driving CS high. Figure 7-45. Read Quad Manufacturer/ Device ID Quad I/O instruction (SPI Mode) JEDEC ID (9Fh) For compatibility reasons, the AT25SL321 provides several instructions to electronically determine the identity of the device. The Read JEDEC ID instruction is congruous with the JEDEC standard for SPI compatible serial flash memories that was adopted in 2003. The instruction is entered by driving the CS pin low with following the instruction code "9Fh". JEDEC assigned Manufacturer ID byte for Adesto (1Fh) and two Device ID bytes, Memory Type (ID-15-ID8) and Capacity (ID7-ID0) are then shifted out on the falling edge of SCK with most significant bit (MSB) first shown in Figure 7-46 and Figure 7-47. For memory type and capacity values refer to Manufacturer and Device Identification table. The JEDEC ID can be read continuously. The instruction is terminated by driving CS high. AT25SL321 DS-25SL321-112F-3/2017 41 Figure 7-46. Read JEDEC ID instruction (SPI Mode) Figure 7-47. Read JEDEC ID instruction (QPI Mode) 7.28 Enable QPI (38h) The AT25SL321 support both Standard/Dual/Quad Serial Peripheral interface (SPI) and Quad Peripheral Interface (QPI). However, SPI mode and QPI mode cannot be used at the same time. Enable QPI instruction is the only way to switch the device from SPI mode to QPI mode. AT25SL321 DS-25SL321-112F-3/2017 42 In order to switch the device to QPI mode, the Quad Enable (QE) bit in Status Register 2 must be set to 1 first, and an Enable QPI instruction must be issued. If the Quad Enable (QE) bit is 0, the Enable QPI instruction will be ignored and the device will remain in SPI mode. After power-up, the default state of the device is SPI mode. See the instruction Set Table 7.1 for all the commands supported in SPI mode and the instruction Set Table 7-5 for all the instructions supported in QPI mode. When the device is switched from SPI mode to QPI mode, the existing Write Enable and Program/Erase Suspend status, and the Wrap Length setting will remain unchanged. Figure 7-48. Enable QPI instruction (SPI Mode only) 7.29 Disable QPI (FFh) By issuing Disable QPI (FFh) instruction, the device is reset SPI mode. When the device is switched from QPI mode to SPI mode, the existing Write Enable Latch (WEL) and Program/Erase Suspend status, and the Wrap Length setting will remain unchanged. Figure 7-49. Disable QPI instruction for QPI mode AT25SL321 DS-25SL321-112F-3/2017 43 7.30 Word Read Quad I/O (E7h) The Quad I/O dramatically reduces instruction overhead allowing faster random access for code execution (XIP) directly from the Quad SPI. The Quad Enable bit (QE) of Status Register-2 must be set to enable the Word Read Quad I/O instruction. The lowest Address bit (A0) must equal 0 and only two dummy clocks are required prior to the data output. Continuous Read Mode The Word Read Quad I/O instruction can further reduce instruction overhead through setting the "Continuous Read Mode" bits (M7-0) after the input Address bits (A23-0), as shown in Figure 7-50. The upper nibble of the (M7-4) controls the length of the next Word Read Quad I/O instruction through the inclusion or exclusion of the first byte instruction code. The lower nibble bits of the (M[3:0]) are don't care ("X"). However, the IO pins should be highimpedance prior to the falling edge of the first data out clock. If the "Continuous Read Mode" bits M[7-4]= Ah, then the next Fast Read Quad I/O instruction (after CS is raised and then lowered) does not require the E7h instruction code, as shown in Figure 7-51. This reduces the instruction sequence by eight clocks and allows the Read address to be immediately entered after CS is asserted low. If the "Continuous Read Mode" bits M[7:4] do not equal to Ah(1,0,1,0) the next instruction (after CS is raised and then lowered) requires the first byte instruction code, thus returning to normal operation. Figure 7-50. Word Read Quad I/O instruction (Initial instruction or previous set M70 Axh, SPI Mode) Figure 7-51. Word Read Quad I/O instruction (Previous instruction set M70= Axh, SPI Mode) AT25SL321 DS-25SL321-112F-3/2017 44 Wrap Around in SPI mode The Word Read Quad I/O instruction can also be used to access a specific portion within a page by issuing a "Set Burst with Wrap" (77h) instruction prior to E7h. The "Set Burst with Wrap" (77h) instruction can either enable or disable the "Wrap Around" feature for the following E7h commands. When "Wrap Around" is enabled, the output data starts at the initial address specified in the instruction, once it reaches the ending boundary of the 8/16/32/64-byte section, the output will wrap around to the beginning boundary automatically until CS is pulled high to terminate the instruction. The Burst with Wrap feature allows applications that use cache to quickly fetch a critical address and then fill the cache afterwards within a fixed length (8/16/32/64-byte) of data without issuing read instructions. The "Set Burst with Wrap" instruction allows three "Wrap Bits", W64 to be set. The W4 bit is used to enable or disable the "Wrap Around" operation while W6-5 is used to specify the length of the wrap around section within a page. See 10.35 for detail descriptions. 7.31 Set Burst with Wrap (77h) The Set Burst with Wrap (77h) instruction is used in conjunction with "Fast Read Quad I/O" and "Word Read Quad I/O" instructions to access a fixed length of 8/16/32/64-byte section within a 256-byte page. Certain applications can benefit from this feature and improve the overall system code execution performance. Before the device will accept the Set Burst with Wrap instruction, a Quad enable of Status Register-2 must be executed (Status Register bit QE must equal 1). The Set Burst with Wrap instruction is initiated by driving the CS pin low and then shifting the instruction code "77h" followed by 24 dummy bits and 8 "Wrap Bits", W7-0. The instruction sequence is shown in Set Burst with Wrap Instruction Sequence. Wrap bit W7 and W30 are not used. W4 = 0 W6, W5 Wrap Around W4 = 1(Default) Wrap Length 8-byte Wrap Around Wrap Length 00 Yes No N/A 01 Yes 16-byte No N/A 10 Yes 32-byte No N/A 11 Yes 64-byte No N/A Once W6-4 is set by a Set Burst with Wrap instruction, all the following "Fast Read Quad I/O" and Word Read Quad I/O instructions will use the W6-4 setting to access the 8/16/32/64byte section within any page. To exit the "Wrap Around" function and return to normal read operation, another Set Burst with Wrap instruction should be issued to set W4 = 1. The default value of W4 upon power on is 1. In the case of a system Reset while W4 = 0, it is recommended that the controller issues a Set Burst with Wrap instruction or Reset (99h) instruction to reset W4 = 1 prior to any normal Read instructions since AT25SL321 does not have a hardware Reset Pin. AT25SL321 DS-25SL321-112F-3/2017 45 Figure 7-52. Set Burst with Wrap Instruction Sequence 7.32 Burst Read with Wrap (0Ch) The "Burst Read with Wrap (0Ch)" instruction provides an alternative way to perform the read operation with "Wrap Around" in QPI mode. The instruction is similar to the "Fast Read (0Bh)" instruction in QPI mode, except the addressing of the read operation will "Wrap Around" to the beginning boundary of the "Wrap Length" once the ending boundary is reached. The "Wrap Length" and the number of dummy of clocks can be configured by the "Set Read Parameters (C0h)" instruction. Figure 7-53. Burst Read with Wrap instruction (QPI Mode, 80MHz) AT25SL321 DS-25SL321-112F-3/2017 46 Figure 7-54. Burst Read with Wrap instruction (QPI Mode, 104MHz) 7.33 Set Read Parameters (C0h) In QPI mode, to accommodate a wide range of applications with different needs for either maximum read frequency or minimum data access latency, "Set Read Parameters (C0h)" instruction can be used to configure the number of dummy clocks for "Fast Read (0Bh)", "Fast Read Quad I/O (EBh)" & "Burst Read with Wrap (0Ch)" instructions, and to configure the number of bytes of "Wrap Length" for the "Burst Read with Wrap (0Ch)" instruction. In Standard SPI mode, the "Set Read Parameters (C0h)" instruction is not accepted. The dummy clocks for various Fast Read instructions in Standard/Dual/Quad SPI mode are fixed, please refer to the instruction. and for details Table 7.1, Table 7-3, Table 7-4, and Table 7-5. The "Wrap Length" is set by W6-5 bit in the "Set Burst with Wrap (77h)" instruction. This setting will remain unchanged when the device is switched from Standard SPI mode to QPI mode. The default "Wrap Length" after a power up or a Reset instruction is 8 bytes, the default number of dummy clocks is 4. Dummy Clocks P4 Maximum Read Freq. 0 0 4 80MHz 1 1 8 104MHz* P1, P0 Wrap Length 0 0 8-byte 0 1 16-byte 1 0 32-byte 1 1 64-byte AT25SL321 DS-25SL321-112F-3/2017 47 Figure 7-55. Set Read Parameters instruction (QPI Mode) 7.34 Enable Reset (66h) and Reset (99h) Because of the small package and the limitation on the number of pins, the AT25SL321 provide a software Reset instruction instead of a dedicated RESET pin. Once the Reset instruction is accepted, any on-going internal operations will be terminated and the device will return to its default power-on state and lose all the current volatile settings, such as Volatile Status Register bits, Write Enable Latch (WEL) status, Program/Erase Suspend status, Continuous Read Mode bit setting, Read parameter setting and Wrap bit setting. "Enable Reset (66h)" and "Reset (99h)" instructions can be issued in either SPI mode or QPI mode. To avoid accidental reset, both instructions must be issued in sequence. Any other instructions other than "Reset (99h)" after the "Enable (66h)" instruction will disable the "Reset Enable" state. A new sequence of "Enable Reset (66h)" and "Reset (99h)" is needed to reset the device. Once the Reset instruction is accepted by the device will take approximately tRST= 30us to reset. During this period, no instruction will be accepted. Data corruption may happen if there is an on-going or suspended internal Erase or Program operation when Reset instruction sequence is accepted by device. It is recommended to check the BUSY bit and the SUS bit in Status Register before issuing the Reset instruction sequence. AT25SL321 DS-25SL321-112F-3/2017 48 Figure 7-56. Enable Reset and Reset Instruction (SPI Mode) Figure 7-57. Enable Reset and Reset Instruction (QPI Mode) 7.35 Read Serial Flash Discovery Parameter (5Ah) The Read Serial Flash Discovery Parameter (SFDP) instruction allows reading the Serial Flash Discovery Parameter area (SFDP). This SFDP area is composed of 2048 readonly bytes containing operating characteristics and vendor specific information. The SFDP area is factory programmed. If the SFDP area is blank, the device is shipped with all the SFDP bytes at FFh. If only a portion of the SFDP area is written to, the portion not used is shipped with bytes in erased state (FFh). The instruction sequence for the read SFDP has the same structure as that of a Fast Read instruction. First, the device is selected by driving Chip Select (CS) Low. Next, the 8bit instruction code (5Ah) and the 24bit address are shifted in, followed by 8 dummy clock cycles. The bytes of SFDP content are shifted out on the Serial Data Output (SO) starting from the specified address. Each bit is shifted out during the falling edge of Serial Clock (SCK). The instruction sequence is shown here. The Read SFDP instruction is terminated by driving Chip Select (CS) High at any time during data output. AT25SL321 DS-25SL321-112F-3/2017 49 Figure 7-58. Read SFDP Register Instruction Table 7-6. SFDP Signature and Headers Description Comment SFDP Signature Address (h) Byte Address (Bit) Data (b) (Bit) Data (h) (Byte) 00h 07:00 0101 0011 53h 01h 15:08 0100 0110 46h 02h 23:16 0100 0100 44h 03h 31:24 0101 0110 50h SFDP Minor Revision Start from 00h 04h 07:00 0000 0110 06h SFDP Major Revision Start from 01h 05h 15:08 0000 0001 01h Number of Parameters Headers Start from 00h 06h 23:16 0000 0001 01h Reserved FFh 07h 31:24 1111 1111 FFh JEDEC Parameter ID (LSB) JEDEC Parameter ID (LSB) = 00H 08h 07:00 0000 0000 00h Parameter Table Minor Revision Start from 00H 09h 15:08 0000 0110 06h Parameter Table Major Revision Start from 01H 0Ah 23:16 0000 0001 01h 0Bh 31:24 0001 0000 10h Parameter Table Length (double words) How many DWORDs in the parameter table AT25SL321 DS-25SL321-112F-3/2017 50 Description Parameter Table Pointer Comment Address of Adesto Parameter Table Address (h) Byte Address (Bit) Data (b) (Bit) Data (h) (Byte) 0Ch 07:00 0011 0000 30h 0Dh 15:08 0000 0000 00h 0Eh 23:16 0000 0000 00h JEDEC Parameter ID (MSB) JEDEC Parameter ID (MSB):FFH 0Fh 31:24 1111 1111 FFh JEDEC Parameter ID (LSB) Adesto Manufacturer ID 10h 07:00 0001 1111 1Fh Parameter Table Minor Revision Start from 00H 11h 15:08 0000 0000 00h Parameter Table Major Revision Start from 01H 12h 23:16 0000 0001 01h 13h 31:24 0000 0010 02h 14h 07:00 1000 0000 80h 15h 15:08 0000 0000 00h 16h 23:16 0000 0000 00h 17h 31:24 0000 0001 01h Parameter Table Length (double words) How many DWORDs in the parameter table Parameter Table Pointer (PTP) Address of Adesto Parameter Table Reserved Table 7-7. FFh SFDP Parameters Table 1 Description Erase Granularity Comment Address (h) Byte 01:4KB available 11:4KB not available Write Granularity 0:1Byte, 1:64 bytes or larger Volatile Status Register Block Protect Bits 0: Nonvolatile status bit Volatile Status Register Write Enable Opcode 0:50H Opcode to enable, if bit-3 = 1 1: Volatile status bit 30h Reserved 4KB Erase Opccde Opcode or FFh 31h Address (Bit) Data (b) (Bit) 01:00 01 02 1 03 0 04 0 07:05 111 15:08 0010 0000 Data (h) (Byte) E5h 20h AT25SL321 DS-25SL321-112F-3/2017 51 Description Comment Fast Dual Read Output (1 -1 -2) 0=Not supported, 1=Supported Number of Address Bytes Address (h) Byte Address (Bit) Data (b) (Bit) 16 1 18:17 00 19 0 Data (h) (Byte) 00:3 Byte only 01:3 or 4 Byte 10:4 Byte only 11:Reserved Double Transfer Rate (DTR) Clocking 0=Not supported, 1=Supported Fast Dual I/O Read (1-2- 2) 0=Not supported, 1=Supported 20 1 Fast Quad I/O Read (1-4-4) 0=Not supported, 1=Supported 21 1 Fast Quad Output Read (1-1-4) 0=Not supported, 1=Supported 22 1 23 1 33h 31:24 1111 1111 FFh 34h 07:00 1111 1111 FFh 35h 15:08 1111 1111 FFh 36h 23:16 1111 1111 FFh 37h 31:24 0000 0001 01h 04:00 00100 Reserved FFh Reserved FFh Flash Memory Density Fast Quad I/O (1-4-4) Number of dummy clocks 32h number of dummy clocks F1h 38h Fast Quad I/O (1-4-4) Number of mode bits number of mode bits Fast Quad I/O (1-4-4) Read Opcode Opcode or FFh Fast Quad Output (1-1-4) Number of dummy clocks number of dummy clocks Fast Quad Output (1-1-4) Number of mode bits number of mode bits Fast Quad Output (1-1-4) Read Opcode Opcode or FFh Fast Dual Output (1-1-2) Number of dummy clocks number of dummy clocks Fast Dual Output (1-1-2) Number of mode bits number of mode bits Fast Dual Output (1-1-2) Read Opcode Opcode or FFh 39h 44h 07:05 010 15:08 1110 1011 20:16 01000 3Ah 3Bh 08h 23:21 000 31:24 0110 1011 04:00 01000 3Ch 3Dh EBh 6Bh 08h 07:05 000 15:08 0011 1011 3Bh AT25SL321 DS-25SL321-112F-3/2017 52 Description Fast Dual I/O (1-2-2) Number of dummy clocks Comment number of dummy clocks number of mode bits Fast Dual I/O (1-2-2) Read Opcode Opcode or FFh Fast Dual DPI (2-2-2) 0=Not supported, 1=Supported Fast Quad QPI (4-4-4) Address (Bit) Data (b) (Bit) 20:16 00000 3Eh Fast Dual I/O (1-2-2) Number of mode bits Reserved Address (h) Byte FFh 0=Not supported, 1=Supported 3Fh 40h Data (h) (Byte) 80h 23:21 100 31:24 1011 1011 0 0 03:01 111 04 1 07:05 111 BBh FEh Reserved FFh Reserved FFh 41h 15:08 1111 1111 FFh Reserved FFh 42h 23:16 1111 1111 FFh Reserved FFh 43h 31:24 1111 1111 FFh Reserved FFh 44h 07:00 1111 1111 FFh Reserved FFh 45h 15:08 1111 1111 FFh 20:16 0 0000 Fast Dual DPI (2-2-2) Number of dummy clocks number of dummy clocks 46h Fast Dual DPI (2-2-2) Number of mode bits number of mode bits Fast Dual DPI(2-2-2) Read Opcode Opcode or FFh Reserved Reserved Fast Quad QPI (4-4-4) Number of dummy clocks 23:21 000 47h 31:24 1111 1111 FFh FFh 48h 07:00 1111 1111 FFh FFh 49h 15:08 1111 1111 FFh 20:16 00010 number of dummy clocks 4Ah Fast Quadl QPI (4-4-4) Number of mode bits number of mode bits Fast Quad QPI(4-4-4) Read Opcode Opcode or FFh 4Bh 4KB=2^0Ch, 32KB=2^0Fh,64KB=2^10h; (2^Nbyte) 4Ch Opcode or FFh 4Dh 4KB=2^0Ch, 32KB=2^0Fh,64KB=2^10h; (2^Nbyte) Opcode or FFh Erase type-1 Size Erase type-1 Opcode Erase type-2 Size Erase type-2 Opcode 00h 42h 23:21 010 31:24 1110 1011 EBh 0000 1100 0Ch 15:08 0010 0000 20h 4Eh 23:16 0000 1111 0Fh 4Fh 31:24 0101 0010 52h 07:00 AT25SL321 DS-25SL321-112F-3/2017 53 Description Erase Type-3 Size Erase Type-3 Opcode Erase Type-4 Size Erase Type-4 Opcode Comment Address (h) Byte Address (Bit) Data (b) (Bit) Data (h) (Byte) 0001 0000 10h 4KB=2^0Ch, 32KB=2^0Fh,64KB=2^10h; (2^Nbyte) 50h Opcode or FFh 51h 15:08 1101 1000 D8h 4KB=2^0Ch, 32KB=2^0Fh,64KB=2^10h; (2^Nbyte) 52h 23:16 0000 0000 00h Opcode or FFh 53h 31:24 1111 1111 FFh 07:00 Erase Maximum/Typical Ratio Maximum = 2 * (COUNT + 1) * Typical 03:00 0011 Erase type-1 Typical time Count or 00h 08:04 0 0011 10:09 01 15:11 0110 0 17:16 01 00b: 1ms Erase type-1 Typical units 01b: 16ms 10b: 128ms 11b: 1s Erase type-2 Typical time Count or 00h 00b: 1ms Erase type-2 Typical units Erase type-3 Typical time 01b: 16ms 54h 10b: 128ms 55h 11b: 1s 56h Count or 00h 57h 33h 62h D5h 22:18 101 01 24:23 01 29:25 00 000 31:30 00 03:00 0100 07:04 1000 00h 00b: 1ms Erase type-3 Typical units 01b: 16ms 10b: 128ms 11b: 1s Erase type-4 Typical time Count or 00h 00b: 1ms Erase type-4 Typical units 01b: 16ms 10b: 128ms 11b: 1s Program Maximum/Typical Ratio Page Size Maximum = 2 * (COUNT + 1) * Typical 2^N bytes 58h 84h AT25SL321 DS-25SL321-112F-3/2017 54 Address (Bit) Data (b) (Bit) 12:08 0 1001 13 1 17:14 01 00 18 0 22:19 000 0 23 0 28:24 0 0100 30:29 10 1h 31 1 Prohibited Op during Program Suspend see datasheet 03:00 11010 Prohibited Op during Erase Suspend see datasheet Description Program Page Typical time Program Page Typical units Program Byte Typical time, 1st byte Program Byte Typical units, 1st byte Program Additional Byte Typical time Comment Address (h) Byte Count or 00h 0: 8us, 1: 64us Count or 00h 0: 1us, 1: 8us 59h Count or 00h Program Additional Byte Typical units 0: 1us, Erase Chip Typical time Count or 00h 5Ah 5Bh 1: 8us Data (h) (Byte) 29h 01h C4h 00b: 16ms Erase Chip Typical units 01b: 256ms 10b: 4s 11b: 64s Reserved 5Ch ECh 07:04 1110 AT25SL321 DS-25SL321-112F-3/2017 55 Address (Bit) Data (b) (Bit) 1h 08 1 Program Resume to Suspend time Count of 64us 12:09 0 000 Program Suspend Maximum time Count or 00h 17:13 11 101 19:18 01 Description Reserved Comment Address (h) Byte Data (h) (Byte) 00b: 128ns, Program Suspend Maximum units 01b: 1us, 10b: 8us, 11b: 64us Erase Resume to Suspend time Count of 64us Erase Suspend Maximum time Count or 00h 5Dh 5Eh 5Fh A1h 23:20 0000 28:24 1 1101 30:29 01 31 0 07h 3Dh 00b: 128ns, Erase Suspend Maximum units 01b: 1us, 10b: 8us, 11b: 64us Suspend / Resume supported 0: Program and Erase suspend supported 1: not supported Program Resume Opcode Opcode or FFh 60h 7:0 0111 1010 7Ah Program Suspend Opcode Opcode or FFh 61h 15:8 0111 0101 75h Resume Opcode Opcode or FFh 62h 23:16 0111 1010 7Ah Suspend Opcode Opcode or FFh 63h 31:24 0111 0101 75h 01:00 11 07:02 1111 01 Reserved 11b xxxxx1b: Opcode = 05h, bit-0 = 1 Busy, Status Register Busy Polling xxxx1xb: Opcode = 70h, bit-7 = 0 Busy, 64h F7h others: reserved AT25SL321 DS-25SL321-112F-3/2017 56 Description Exit Deep Powerdown time Comment Address (h) Byte Count or 00h Address (Bit) Data (b) (Bit) 12:08 0 0010 14:13 01 Data (h) (Byte) 00b: 128ns, Exit Deep Powerdown units 01b: 1us, 10b: 8us, 11b: 64us Exit Deep Powerdown Opcode Opcode or FFh Enter Deep Powerdown Opcode Opcode or FFh 65h 66h A2h 22:15 101 0101 1 67h 5Ch 30:23 101 1100 1 31 0 Disable 4-4-4 Read Mode 03:00 1001 Enable 4-4-4 Read Mode 08:04 0 0001 09 1 15:10 1111 01 19:16 1100 22:20 001 23 0 31;24 1111 1111 06:00 110 1000 07 1 Deep Powerdown Supported Fast Quad I/O Continuous (0-4-4) supported D5h 0: Deep Powerdown supported, 1: not supported 0: not supported, 1: Quad I/O 0-4-4 supported Fast Quad I/O Continuous (0-4-4) Exit 68h 19h 69h Fast Quad I/O Continuous (0-4-4) Enter 6Ah Quad Enable Requirements (QER) F6h 1Ch 0: not supported, HOLD or RESET Disable Reserved 1: use Configuration Register bit-4 FFh Status Register Opcode Reserved 1h 6Bh 6Ch FFh E8h Soft Reset Opcodes 6Dh 13:08 01 0000 4Byte Address Exit 6Eh 23:14 1100 0000 00 10h C0h 4Byte Address Enter 6Fh 31:24 1000 0000 80h AT25SL321 DS-25SL321-112F-3/2017 57 Table 7-8. SFDP Parameters Table 2 Description Comment Address (h) Byte Address (Bit) Data (b) (Bit) Data (h) (Byte) 0000 0000 00h 17h 1650h: 1.65V, 1700h: 1.70V, VCC Minimum Voltage 2300h: 2.30V, 2500h: 2.50V, 80h 81h 15:0 0001 0111 2700h: 2.70V 1950h: 1.95V, VCC Maximum Voltage 3600h: 3.60V, 82h 4000h: 4.00V, 83h 31:16 0000 0000 0010 0000 00h 20h 4400h: 4.40V Array Protection Method Power up Protection default 10b: use non-volatile status register 0: power up unprotected, 1: power up protected Protection Disable Opcodes 011b: use status register Protection Enable Opcodes 011b: use status register Protection Read Opcodes 011b: use status register Protection Register Erase Opcode Protection Register Program Opcode 84h 85h 01:00 00 02 0 05:03 00 0 08:06 0 00 11:09 000 13:12 00 15:14 00 00h 00h 00b: not supported, 01b: Opcodes 3Dh,2Ah,7Fh,CFh, 00b: not supported, 01b: Opcodes 3Dh,2Ah,7Fh,FCh Reserved FFh 86h 23:16 1111 1111 FFh Reserved FFh 87h 31:24 1111 1111 FFh Reserved FFh 88h-FFh 7.36 Reserved Enter Secured OTP (B1h) The Enter Secured OTP instruction is for entering the additional 4K-bit secured OTP mode. The additional 4K-bit secured OTP is independent from main array, which may be used to store unique serial number for system identifier. After entering the Secured OTP mode, and then follow standard read or program, procedure to read out the data or update data. The Secured OTP data cannot be updated again once it is lock-down Please note that Write Status Register-1, Write Status Register-2 and Write Security Register instructions are not acceptable during the access of secure OTP region. Once security OTP is lock down, only commands related with read are valid. The Enter Secured OTP instruction sequence is shown in Figure 7-59. AT25SL321 DS-25SL321-112F-3/2017 58 Figure 7-59. Enter Secured OTP instruction for SPI Mode (left) and QPI Mode (right) 7.37 Exit Secured OTP (C1h) The Exit Secured OTP instruction is for exiting the additional 4Kbit secured OTP mode. (Please refer to Figure 7-60). Figure 7-60. Exit Secured OTP instruction for SPI Mode (left) and QPI Mode (right) 7.38 Read Security Register (2Bh) The Read Security Register can be read the value of Security Register bits at any time (even in program/erase/write status register-1 and write status register-2 condition) and continuously. Secured OTP Indicator bit. The Secured OTP indicator bit shows the chip is locked by factory before ex-factory or not. When it is "0", it indicates non-factory lock, "1" indicates factory-lock. Lock-down Secured OTP (LDSO) bit. By writing Write Security Register instruction, the LDSO bit may be set to "1" for customer lockdown purpose. However, once the bit it set to "1" (Lockdown), the LDSO bit and the 4Kbit Secured OTP area cannot be updated any more. While it is in 4Kbit Secured OTP mode, array access is not allowed to write. AT25SL321 DS-25SL321-112F-3/2017 59 Table 7-9. Bit7 x Security Register Definition Bit6 x Bit5 x Bit4 x Bit3 x Bit2 x Reserved Reserved Reserved Reserved Reserved Reserved Volatile bit Volatile bit Volatile bit Volatile bit Volatile bit Volatile bit Bit1 Bit0 LDSO (indicate if lock- down) Secured OTP indicator bit 0 = not lockdown 1 = lockdown (cannot program/ erase OTP) 0 = non factory lock 1 = factory lock Non Non Volatile bit Volatile bit Figure 7-61. Read Security Register instruction (SPI Mode) Figure 7-62. Read Security Register instruction (QPI Mode) AT25SL321 DS-25SL321-112F-3/2017 60 7.39 Write Security Register (2Fh) The Write Security Register instruction is for changing the values of Security Register bits. Unlike Write Status Register, the Write Enable instruction is not required before writing Write Security Register instruction. The Write Security Register instruction may change the value of bit1 (LDSO bit) for customer to lock-down the 4K-bit Secured OTP area. Once the LDSO bit is set to "1", the Secured OTP area cannot be updated any more. The CS must go high exactly at the boundary; otherwise, the instruction will be rejected and not executed. Figure 7-63. Write Security Register instruction for SPI Mode (left) and QPI Mode (right) 7.40 4K-bit Secured OTP It's for unique identifier to provide 4K-bit one-time-program area for setting device unique serial number which may be set by factory or system customer. Please refer to table of "4K-bit secured OTP definition". - Security register bit 0 indicates whether the chip is locked by factory or not. - To program the 4K-bit secured OTP by entering 4K-bit secured OTP mode (with ENSO command) and going through normal program procedure, and then exiting 4K-bit secured OTP mode by writing EXSO command - Customer may lock-down bit1 as "1". Please refer to "table of security register definition" for security register bit definition and table of "4K-bit secured OTP definition" for address range definition. Note. Once lockdown whatever by factory or customer, it cannot be changed any more. While in 4K-bit secured OTP mode, array access is not allowed to write. Address Range Size 000000 ~ 00000F 128-bit 000010 ~ 0001FF 3968-bit Standard Factory Lock ESN (Electrical Serial Number) Customer Lock Determined by customer N/A AT25SL321 DS-25SL321-112F-3/2017 61 8. Electrical Characteristics 8.1 Absolute Maximum Ratings(1) PARAMETERS SYMBOL CONDITIONS RANGE UNIT Supply Voltage VCC Voltage Applied to Any Pin VIO Transient Voltage on any Pin VIOT Storage Temperature TSTG 65 Lead Temperature TLEAD See Note(2) C Electrostatic Discharge Voltage VESD 2000 to +2000 V 0.6 to VCC+0.4 V Relative to Ground -0.6 to VCC +0.4 V <20nS Transient Relative to Ground 1.0V to VCC +1.0V V to +150 C Human Body Model(3) Notes: 1. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. The "Absolute Maximum Ratings" are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Voltage extremes referenced in the "Absolute Maximum Ratings" are intended to accommodate short duration undershoot/overshoot conditions and does not imply or guarantee functional device operation at these levels for any extended period of time. 2. Compliant with JEDEC Standard J-STD-20C for small body Sn-Pb or Pb-free (Green) assembly and the European directive on restrictions on hazardous substances (RoHS) 2002/95/EU. 3. JEDEC Std JESD22-A114A (C1=100pF, R1=1500 ohms, R2=500 ohms). 8.2 Operating Ranges PARAMETER SYMBOL Erase/Program Cycles VCC Ambient Operating Temperature 8.3 CONDITIONS MIN MAX FR = 104MHz (Single/Dual/Quad SPI) fR = 50MHz (Read Data 03h) 1.7 2.0 V 40 +85 C TA Industrial UNIT Endurance and Data Retention PARAMETER CONDITIONS Erase/Program Cycles 4KB Block, 32/64KB block or full chip. Data Retention Full Temperature Range MIN MAX UNIT Cycles 100,000 20 years AT25SL321 DS-25SL321-112F-3/2017 62 8.4 Power-up Timing and Write Inhibit Threshold SPEC PARAMETER SYMBOL MIN MAX UNIT VCC(min) to CS Low tVSL(1) 10 s Time Delay Before Write Instruction tPUW (1) 1 10 ms Write Inhibit Threshold Voltage VWI(1) 1.0 1.4 V Note: 1. These parameters are characterized at -10C & +85C only Figure 8-1. Powerup Timing and Voltage Levels 8.5 Program Acceleration via ACC Pin The program acceleration function requires applying VHH to the ACC input, and then waiting a period of tWC. Minimum tVHH (rise & fall times) is required for ACC to change to VHH from VIL or VIH. Removing VHH from the ACC pin returns the device to normal operation after a period of tWC. Only Read Status Register and Page Program operation are allowed when ACC is at (VHH). The start address must be entered by the multiples of 4byte (for example xxxxx0, xxxxx4, xxxxx8, xxxxxC). Also the data must be entered with a minimum of 4byte and multiples of 4byte unit when Program Acceleration via ACC Pin. AT25SL321 DS-25SL321-112F-3/2017 63 SPEC PARAMETER SYMBOL MIN MAX UNIT 9.5 V WP pin High Voltage VHH(1) 8.5 WP pin Voltage rise and fall time tVHH 2.2 s WP at VHH and VIL or VIH to first instruction tWC(1) 5 s (1) Note: 1. These parameters are characterized only. Figure 8-2. ACC Program acceleration Timing and Voltage Levels 8.6 DC Electrical Characteristics SPEC PARAMETER SYMBOL Input Capacitance CIN(1) Output Capacitance COUT Input Leakage I/O Leakage TYP MAX UNIT 6 pF 8 pF ILI 2 A ILO 2 A VOUT=0V (2) ICC1 CS=VCC VIN=GND or VCC 10 50 A ICC2 CS=VCC VIN=GND or VCC 2 20 A 7 mA Power Down Current Current Read Data/ Dual/Quad 1MHz MIN VIN=0V(2) (1) Standby Current (2) CONDITION C=0.1 VCC / 0.9VCC ICC3 AT25SL321 DS-25SL321-112F-3/2017 64 Current Read Data/ Dual/Quad 50MHz(2) C=0.1 VCC / 0.9VCC ICC3 Current Read Data/ Dual/Quad 80MHz(2) 15 mA 18 mA 20 mA C=0.1 VCC / 0.9VCC ICC3 Current Read Data/ C=0.1 VCC / 0.9VCC Dual/Quad 104MHz2) ICC3 Current Write Status Register ICC4 CS=VCC 10 20 mA Current page Program ICC5 CS=VCC 15 25 mA Current Block Erase ICC6 CS=VCC 15 25 mA Current Chip Erase ICC7 CS=VCC 15 25 mA Input Low Voltages VIL Input High Voltages VIH Output Low Voltages VOL IOL= 100A Output High Voltages VOH IOH=100A 0.5 VCC x0.8 VCC x0.2 V VCC +0.4 V 0.2 V V VCC -0.2 Notes: 1. Tested on sample basis and specified through design and characterization data, TA = 25C, VCC = 1.8V. 2. Checked Board Pattern. 8.7 AC Measurement Conditions SPEC PARAMETER SYMBOL Load Capacitance Input Rise and Fall Times MIN MAX UNIT CL 30 pF TR, TF 5 ns Input Pulse Voltages VIN 0.2 VCC to 0.8 VCC V Input Timing Reference Voltages IN 0.3 VCC to 0.7 VCC V OUT 0.5 VCC to 0.5 VCC V Output Timing Reference Voltages Note: 1. Output Hi-Z is defined as the point where data out is no longer driven AT25SL321 DS-25SL321-112F-3/2017 65 Figure 8-3. AC Measurement I/O Waveform 8.8 AC Electrical Characteristics SPEC DESCRIPTION SYMBOL ALT MIN TYP MAX UNIT Clock frequency For all instructions, except Read Data (03h) FR Clock freq. Read Data instruction (03h) fR fc D.C. 104(6) D.C. 50 MHz MHz tCLH, tCLL(1) 4.5 ns Clock High, Low Time for Read Data (03h) tCRLH, tCRLL(1) 8 ns Clock Rise Time peak to peak tCLCH(2) 0.1 V/ns Clock Fall Time peak to peak tCHCL(2) 0.1 V/ns Clock High, Low Time except Read Data (03h) CS Active Setup Time relative to Clock tSLCH CS Not Active Hold Time relative to Clock tCHSL Data In Setup Time tDVCH Data In Hold Time tCHDX CS Active Hold Time relative to Clock 5 ns 5 ns tDSU 2 ns tDH 5 ns tCHSH 5 ns CS Not Active Setup Time relative to Clock tSHCH 5 ns CS Deselect Time (for Read instructions/ Write, Erase and Program instructions) tSHSL tCSH 100 ns tSHQZ(2) tDIS 7 ns Clock Low to Output Valid tCLQV tV1 7 ns Clock Low to Output Valid ( Except Main Read ) (3) tCLQV tV2 8 ns Output Disable Time tCSS AT25SL321 DS-25SL321-112F-3/2017 66 Output Hold Time tCLQX tHO 1.5 ns HOLD Active Setup Time relative to Clock tHLCH 5 ns HOLD Active Hold Time relative to Clock tCHHH 5 ns HOLD Not Active Setup Time relative to Clock tHHCH 5 ns HOLD Not Active Hold Time relative to Clock tCHHL 5 ns HOLD to Output Low-Z tHHQX(2) HOLD to Output High-Z tHLQZ(2) Write Protect Setup Time Before CS Low tWHSL(4) 20 ns Write Protect Setup Time After CS High tSHWL(4) 100 ns CS High to Power Down Mode tLZ tHZ 7 ns 12 ns tDP(2) 3 s CS High to Standby Mode without Electronic Signature Read tRES1 (2) 3 s CS High to Standby Mode with Electronic Signature Read tRES2(2) 1.8 s CS High to next Instruction after Suspend tSUS(2) 30 s CS High to next Instruction after Reset tRST(2) 30 s Write Status Register Time tw 10 15 ms Byte Program Time tBP 10 150 s Page Program Time tPP 0.6 5 ms Page Program Time (ACC = 9V) tEP 0.3 3 ms Block Erase Time(4KB) tSE 0.06 0.4 s Block Erase Time(32KB) tBE1 0.20 1.5 s Block Erase Time(64KB) tBE2 0.35 2 s Chip Erase Time tCE 20 80 s Notes: 1. Clock high + Clock low must be less than or equal to 1/fc. 2. Value guaranteed by design and/or characterization, not 100% tested in production. 3. Contains: Read Status Register-1,2/ Read Manufacturer/Device ID, Dual, Quad/ Read JEDEC ID/ Read Security Register/ Read Serial Flash Discovery Parameter. 4. Only applicable as a constraint for a Write Status Register instruction when Sector Protect Bit is set to 1. 5. Commercial temperature only applies to Fast Read (FR). Industrial temperature applies to all other parameters. AT25SL321 DS-25SL321-112F-3/2017 67 8.9 Input Timing 8.10 Output Timing 8.11 Hold Timing AT25SL321 DS-25SL321-112F-3/2017 68 9. Ordering Information 9.1 Ordering Code Detail AT 2 5 S L 3 2 1 - SUE - T Designator Shipping Carrier Option T = Tape and reel Product Family Operating Voltage E = 1.7V to 2.0V Device Grade U = Green, Matte Sn or Sn alloy, Industrial temperature range (-40C to +85C) H = NiPdAu lead-frame Industrial Temp range (-40C+85C) Device Density 321 = 32-megabit Package Option M = 8-pad, 5 x 6 x 0.6 mm UDFN MB = 8-pad, 3 x 4 x 0.55 mm USON S = 8-lead, 0.208" wide SOIC CC = 1 mm pitch BGA U = 8-ball 0.5mm pitch dBGA UA = 10-ball 0.35mm pitch dBGA DWF = Die in Wafer Form Ordering Code (1) Package Lead Finish AT25SL321-MHE-T 8MA1 NiPdAu AT25SL321-MBUE-T 8MA2 AT25SL321-SUE-T 8S4 AT25SL321-CCUE-T 24CC AT25SL321-UUE-T (3) AT25SL321-UAUE-T (3) AT25SL321-DWF (3) 8-WLCSP Operating Voltage Max. Freq. (MHz) 1.7V-2.0V 104 MHz (2) SnAgCu 10-WLCSP Operation Range -40 to 85 (Industrial Temperature Range) DWF 1. The shipping carrier option code is not marked on the devices. 2. Contact Adesto for availability of 133MHz operating frequency. 3. Contact Adesto for mechanical drawing or sales information. Package Type 8S4 8-lead, 0.208" Wide, Plastic Gull Wing Small Outline Package (EIAJ SOIC) 8MA1 8-pad (5 x 6 x 0.6 mm body), Thermally Enhanced Plastic Ultra-Thin Dual Flat No-lead (UDFN) 8MA2 8-pad (3 x 4 x 0.55 mm body), Thermally Enhanced Plastic Ultra-Thin Small Outline No-lead (USON) AT25SL321 DS-25SL321-112F-3/2017 69 Package Type 24CC 24-ball, 1 mm pitch, Ball Grid Array (BGA) 8-WLCSP 8-ball, 0.5mm pitch, die Ball Grid Array (dBGA) 10-WLCSP 10-ball, 0.35mm pitch, die Ball Grid Array (dBGA) DWF Die in Wafer Form AT25SL321 DS-25SL321-112F-3/2017 70 10. Packaging Information- 10.1 8S4 - 8-lead, .208" EIAJ SOIC SYMBOL MILLIMETERS INCHES MIN NOM MAX MIN NOM MAX A 1.75 1.95 2.16 0.069 0.077 0.085 A1 0.05 0.15 0.25 0.002 0.006 0.010 A2 1.70 1.80 1.91 0.067 0.071 0.075 B 0.35 0.42 0.48 0.014 0.017 0.019 C 0.19 0.20 0.25 0.007 0.008 0.010 D 5.18 5.28 5.38 0.204 0.208 0.212 E 7.70 7.90 8.10 0.303 0.311 0.319 E1 5.18 5.28 5.38 0.204 0.208 0.212 e 1.27 BSC 0.050 BSC L 0.50 0.65 0.80 0.020 0.026 0.031 0 - 8 0 - 8 Y - - 0.10 - - 0.004 (R) Package Drawing Contact: contact@adestotech.com TITLE 8S4, 8-lead, 0.208" Body, Plastic Small Outline Package (EIAJ) GPC DRAWING NO. STN 8S4 6/13/17 REV. AT25SL321 DS-25SL321-112F-3/2017 B 71 10.2 8MA1 - UDFN E C Pin 1 ID SIDE VIEW D y TOP VIEW A1 A K E2 0.45 8 Option A Pin #1 Cham fer (C 0.35) 1 Pin #1 Notch (0.20 R) (Option B) 7 e 6 MIN NOM MAX A 0.45 0.55 0.60 A1 0.00 0.02 0.05 b 0.35 0.40 0.48 SYMBOL 2 D2 COMMON DIMENSIONS (Unit of Measure = mm) 3 C 5 4 b BOTTOM VIEW L NOT E 0.152 REF D 4.90 5.00 5.10 D2 3.80 4.00 4.20 E 5.90 6.00 6.10 E2 3.20 3.40 3.60 e 1.27 L 0.50 0.60 0.75 y 0.00 - 0.08 K 0.20 - - 4/15/08 TITLE (R) Package Drawing Contact: contact@adestotech.com 8MA1, 8-pad (5 x 6 x 0.6 mm Body), Thermally Enhanced Plastic Ultra Thin Dual Flat No Lead Package (UDFN) GPC YFG DRAWING NO. 8MA1 REV. D AT25SL321 DS-25SL321-112F-3/2017 72 10.3 8MA2 - USON SIDE VIEW TOP VIEW 0.45 COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM MAX A 0.50 0.55 0.60 A1 0.00 0.02 0.05 A2 - 0.15 - A3 0.35 0.40 0.45 b 0.25 0.30 0.35 D 2.90 3.00 3.10 SYMBOL D1 0.10 0.20 0.30 L 0.55 0.60 0.65 e BOTTOM VIEW NOT E 0.80 BSC E 3.90 4.00 4.10 E1 0.70 0.80 0.90 10/25/16 TITLE (R) Package Drawing Contact: contact@adestotech.com 8MA2, 8-pad (3 x 4 x 0.55 mm Body), Thermally Enhanced Plastic Ultra Thin Small Outline No Lead Package (USON) GPC YFG DRAWING NO. 8MA2 AT25SL321 DS-25SL321-112F-3/2017 REV. A 73 10.4 24CC -- 24-ball BGA 5/5/16 Package Drawing Contact: contact@adestotech.com TITLE GPC DRAWING NO. REV. 24CC, 24-ball, 6 x 8 x 1.2mm Body, 1.0mm ball pitch (4x6 Array), Ball Grid Array Package(BGA) CAA 24CC A AT25SL321 DS-25SL321-112F-3/2017 74 8-WLCSP -- die Ball Grid Array 1 2 1 2 A A 5 10.5 B B C C D D 5 ALL DIMENSIONS ARE IN MM Pin Assignment Matrix A B 1 V CC I/O3(HOLD) 2 CS I/O1(SO) C D I/O0(SI) SCK I/O2(WP) GND 1/4/2017 (R) TITLE 8WLCSP, 8-ball, die Ball Grid Array Package Drawing Contact: contact@adestotech.com GPC DRAWING NO. REV. 8WLCSP-A C AT25SL321 DS-25SL321-112F-3/2017 75 10.6 10-WLCSP -- die Ball Grid Array Package Drawing TBC (To Be Confirmed - Contact Adesto for more information) Bottom View Side View 1.596 mm 3 0.2 mm 0.2 mm 0.2 mm 0.2 mm 0.2 mm 1 CS 0.2 mm 0.8 mm 2 Vcc GND I/O1(SO) I/O3(HOLD) I/O0(SI) I/O2(WP) SCK A B C D E F G 2.329 mm 0.35 mm max 0.35 mm 0.35 mm 0.7 mm Unmarked balls are NC Final package outline drawing to be confirmed AT25SL321 DS-25SL321-112F-3/2017 76 11. Revision History Revision Level - Release Date History A - June 2016 Initial release of AT25SL321A datasheet. B - August 2016 Updated 8-WLCSP package outline drawing. Added 10-WLCSP package. Updated voltage range. Removed Sector and Block Protect descriptions. Removed Status Register Memory Protection tables. Updated tCSH specification. C - October 2016 Updated UDFN package drawing and dimensions. Added USON package drawing and dimensions. Updated command description for 50h. Updated SFDP tables. D - November 2016 Updated SFDP tables (to version 1.6). E - February 2017 Updated Note 1 on Table 8.1. F - March 2017 Updated document status from Advanced to Complete. AT25SL321 DS-25SL321-112F-3/2017 77 Corporate Office California | USA Adesto Headquarters 3600 Peterson Way Santa Clara, CA 95054 Phone: (+1) 408.400.0578 Email: contact@adestotech.com (c) 2017 Adesto Technologies. All rights reserved. / Rev.: DS-25SL321-112F-3/2017 Disclaimer: Adesto Technologies Corporation makes no warranty for the use of its products, other than those expressly contained in the Company's standard warranty which is detailed in Adesto's Terms and Conditions located on the Company's web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Adesto are granted by the Company in connection with the sale of Adesto products, expressly or by implication. Adesto's products are not authorized for use as critical components in life support devices or systems.