1-5650090-2 - Tyco Electronics

Product

Specification 108-14034

02Jun08 Rev C

Connector, Card Edge, . 050 Centerline

Harrisburg, PA

All International Rights Reserved.

* Trademark

| Indi cates change For latest revision, visi t ou r website at www.t ycoel ectronics.com\documents.

For Regional Customer Service, visit our website at www.tycoelectronics.com 1 of 6

LOC B

1. SCOPE

1.1. Content

This specification covers performance, tests and quality requirements for Tyco Electronics .050|center line card edge connector. This connector is a mul ti-contact edge board type having contacts for

sol der applicati ons.

1.2. Qualification

When test s are performed on subject pr oduct line, procedures specified in Figure 1 shal l be used. All|i nspections shall be per formed using applicable inspection pl an and product draw ing.

2. APPLI CABLE DOCUMENTS

The follow ing documents form a part of this specification to the extent specified herein. Unless otherwi se

speci fied, latest edition of the document applies. In the event of conflict betw een requirements of this

speci fication and product drawi ng, product drawing shall take precedence. In the event of conf lict

between requirements of this specification and referenced documents, this specif ication shall take

precedence.

2.1. Tyco Electronics Documents|

109-1: General Requirements for Test Speci fications

109 Series: Test Specifications as indicated in Figure 1

114-13148: Application Specification (.050 Series Standard Edge Peripheral Computer|Int erconnect (PCI) Surface Mount Connector Assemblies)|

114-26012: Application Specification (C ard Edge Connectors with Contacts on .050 Inch Centers)|

501-203: Qual ification Test Report (Connector, Card Edge, .050 Series)|

3. REQUIREMENTS

3.1. Desi gn and Construction

Product shall be of design, construction and physi cal dimensions specified on appl icable product

drawing.

3.2. Materials

Contact : Phosphor bronze, gold or gold flash/palladium nickel over nickel plati ng

Housi ng: PPS or PCT

3.3. Ratings

Vol tage: 203 volts AC

Curr ent: Signal application only

Temperature: -55 to 85

Flammability: UL94V-0|

108-14034

Rev C 2 of 6

3.4. Perf ormance and Test Description

Product is designed to meet electrical, mechanical and environmental perfor mance requirements

speci fied in Figur e 1. Unless otherwi se specified, all tests shall be performed at ambient environmental

condi tions per Test Speci fication 109-1.|

3.5. Test Requirements and Procedures Summary

Test Description Requi rement Procedur e

Examination of product. Meets requirements of product

drawing and Application|Speci fications 114-13148 and 114-|26012.

Vi sual, dimensional and functional

per applicable quality inspection

plan.

ELECTRICAL

Termination resistance. 20 milliohms maximum initial.

)

R 10 milliohms maximum final. AMP 109-6-1.

Subject mated contacts assembled

i n housing to 50 mv maximum open

ci rcuit at 100 ma maximum.

See Fi gure 4.

Insulati on resistance. 1000 megohms minimum. AMP Spec 109-28-4.

Test between adjacent contacts of

unmated samples.

Di electric withstanding voltage. 500 volts AC at sea level. AMP Spec 109-29-1.

Test between adjacent contacts of

unmated samples.

MECHANICAL

Vi bration, random. No discontinuities of 1 microsecond

or longer durat ion.

See Note.

AMP Spec 109-21-7, Condition A.

Subject mated samples to 5 to 500

Hz. Fifteen minutes in each of 3|mutual ly per pendicular planes.

Physical shock. No di scontinuiti es of 1 mi crosecond

or longer durat ion.

See Note.

AMP Spec 109-26-9.

Subject mated samples to 100 G's

sawtooth shock pulses of 6

milliseconds duration. T hree shocks|i n each direction appl ied along 3

mutual ly per pendicular planes, 18

tot al shocks.

Durability. See Note. AMP Spec 109-27.

Mate and unmate sampl es for 100

cycles at maximum rate of 500

cycles per hour.

Mating force. 8 ounces maximum per contact

pair. AMP Spec 109-35.

Measure force necessary to mate

printed ci rcuit board to samples

usi ng free floating fix tures at

maximum rate of .5 inch per minute.

Fi gure 1 (continued)

108-14034

Test Description Requi rement Procedur e

Rev C 3 of 6

Unmati ng force. 0.5 ounce mi nimum per cont act

pair. AMP Spec 109-35.

Measure force necessary to unmate

printed ci rcuit board from samples

at maximum rate of .5 inch per

minute.

ENVIRONMENTAL

Thermal shock. See Note. AMP Spec 109-22.

Subject unmated samples to 5

cycles between -55 and 85

Humidity/temperature cycling. See Note. AMP Spec 109-23-3,

Condi tion B.

Subject unmated samples to 10

cycles between 25 and 65

C at 95%

RH.

Temperature life. See Note. AMP Spec 109-43.

Subject mated samples to

temperat ure life at 85

C for 1000

hours.

Mixed f lowing gas. See Note. AMP Spec 109-85-2.

Subject mated samples to

environmental cl ass II for 14 days.

Shall meet visual requirements, show no physical damage and shall meet requirements of

NOTE

additional tests as specified in Test Sequence in Figur e 2.

Fi gure 1 (end)

108-14034

Rev C 4 of 6

3.6. Product Qualification and Requalification Test Sequence

Test or Exami nation Test Group (a)

1234

Test Sequence (b)

Examination of product 1,9 1,5 1,5 1,8

Termination resistance 3,7 2,4 2,4

Insulation resistance 2,6

Di electric withstanding voltage 3,7

Vibration 5

Physical shock 6

Durability 4

Mating force 2

Unmating force 8

Thermal shock 4

Humidity/temperature cycling 5

Temperature life 3(c)

Mixed f lowing gas 3(c)

(a) See paragraph 4.1.A.

NOTE

(b) Numbers indicate sequence in which tests ar e performed.

Fi gure 2

108-14034

Rev C 5 of 6

4. QUALI TY ASSURANCE PROVISIONS

4.1. Qual ification Testi ng

A. Sample Selection

Samples shall be prepared in accordance wi th applicable Instruction Sheets and shall be selected

at r andom from current production. All test groups shall consist of 5 sampl es each.

B. Test Sequence

Qual ification inspection shall be verifi ed by testing samples as specified in Figure 2.

4.2. Requal ification Testi ng

If changes significantly affecting form, fit or function are made to product or manufacturing process,

product assurance shall coordinate requalification testing, consisting of all or part of original testing

sequence as deter mined by development/product, quality and reliability engineering.

4.3. Acceptance

Acceptance is based on verifi cation that product meets requirements of Figure 1. Failures attributed to

equi pment, test setup or operator def ici encies shall not disqualify pr oduct. When product failure occurs,

corr ective action shall be taken and samples resubmitted for qualification. Testing to confirm corrective

action is r equired before resubmittal.

4.4. Qual ity Conformance Inspection

Applicable quality inspection plan will specify sampling acceptable quality level to be used. Dimensional

and funct ional requirements shall be in accordance w ith applicable product drawing and this

specification.

108-14034

Rev C 6 of 6

Fi gure 3

Test Board

Fi gure 4

Termination Resistance Measurement Points