LM75B Digital temperature sensor and thermal watchdog Rev. 5 -- 22 January 2014 Product data sheet 1. General description The LM75B is a temperature-to-digital converter using an on-chip band gap temperature sensor and Sigma-Delta A-to-D conversion technique with an overtemperature detection output. The LM75B contains a number of data registers: Configuration register (Conf) to store the device settings such as device operation mode, OS operation mode, OS polarity and OS fault queue as described in Section 7 "Functional description"; temperature register (Temp) to store the digital temp reading, and set-point registers (Tos and Thyst) to store programmable overtemperature shutdown and hysteresis limits, that can be communicated by a controller via the 2-wire serial I2C-bus interface. The device also includes an open-drain output (OS) which becomes active when the temperature exceeds the programmed limits. There are three selectable logic address pins so that eight devices can be connected on the same bus without address conflict. The LM75B can be configured for different operation conditions. It can be set in normal mode to periodically monitor the ambient temperature, or in shutdown mode to minimize power consumption. The OS output operates in either of two selectable modes: OS comparator mode or OS interrupt mode. Its active state can be selected as either HIGH or LOW. The fault queue that defines the number of consecutive faults in order to activate the OS output is programmable as well as the set-point limits. The temperature register always stores an 11-bit two's complement data giving a temperature resolution of 0.125 C. This high temperature resolution is particularly useful in applications of measuring precisely the thermal drift or runaway. When the LM75B is accessed the conversion in process is not interrupted (that is, the I2C-bus section is totally independent of the Sigma-Delta converter section) and accessing the LM75B continuously without waiting at least one conversion time between communications will not prevent the device from updating the Temp register with a new conversion result. The new conversion result will be available immediately after the Temp register is updated. The LM75B powers up in the normal operation mode with the OS in comparator mode, temperature threshold of 80 C and hysteresis of 75 C, so that it can be used as a stand-alone thermostat with those pre-defined temperature set points. 2. Features and benefits Pin-for-pin replacement for industry standard LM75 and LM75A and offers improved temperature resolution of 0.125 C and specification of a single part over power supply range from 2.8 V to 5.5 V I2C-bus interface with up to 8 devices on the same bus Power supply range from 2.8 V to 5.5 V Temperatures range from 55 C to +125 C LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog Frequency range 20 Hz to 400 kHz with bus fault time-out to prevent hanging up the bus 11-bit ADC that offers a temperature resolution of 0.125 C Temperature accuracy of: 2 C from 25 C to +100 C 3 C from 55 C to +125 C Programmable temperature threshold and hysteresis set points Supply current of 1.0 A in shutdown mode for power conservation Stand-alone operation as thermostat at power-up ESD protection exceeds 4500 V HBM per JESD22-A114 and 2000 V CDM per JESD22-C101 Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA Small 8-pin package types: SO8, TSSOP8, 3 mm 2 mm XSON8U, and 2 mm 3 mm HWSON8 3. Applications LM75B Product data sheet System thermal management Personal computers Electronics equipment Industrial controllers All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 2 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 4. Ordering information Table 1. Ordering information Type number Topside mark Package Name Description Version LM75BD LM75BD SO8 plastic small outline package; 8 leads; body width 3.9 mm SOT96-1 LM75BDP LM75B TSSOP8 plastic thin shrink small outline package; 8 leads; body width 3 mm SOT505-1 LM75BGD[1] 75B XSON8U plastic extremely thin small outline package; no leads; 8 terminals; UTLP based; body 3 2 0.5 mm SOT996-2 LM75BTP M75 HWSON8 plastic thermal enhanced very very thin small outline package; no leads; 8 terminals, 2 3 0.8 mm [1] SOT1069-2 LM75BGD cannot be production cold temperature tested because of manufacturing process constraints. Although no LM75BGD complaints have been noted, NXP recommends consideration/use of the LM75BTP instead of the LM75BGD in operating environments of less than 0 C. 4.1 Ordering options Table 2. Ordering options Type number Orderable part number Package Packing method Minimum order quantity Temperature LM75BD LM75BD,112 SO8 Standard marking * IC's tube DSC bulk pack 2000 Tamb = 55 C to +125 C LM75BD,118 SO8 Reel 13" Q1/T1 *Standard mark SMD 2500 Tamb = 55 C to +125 C LM75BDP LM75BDP,118 TSSOP8 Reel 13" Q1/T1 *Standard mark SMD 2500 Tamb = 55 C to +125 C LM75BGD LM75BGD,125 XSON8U Reel 7" Q3/T4 *Standard mark 3000 Tamb = 55 C to +125 C LM75BTP LM75BTP,147 HWSON8 Reel 7" Q2/T3 *Standard mark 4000 Tamb = 55 C to +125 C LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 3 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 5. Block diagram VCC LM75B BIAS REFERENCE BAND GAP TEMP SENSOR POINTER REGISTER CONFIGURATION REGISTER COUNTER TEMPERATURE REGISTER TIMER TOS REGISTER COMPARATOR/ INTERRUPT THYST REGISTER 11-BIT SIGMA-DELTA A-to-D CONVERTER OSCILLATOR POWER-ON RESET OS LOGIC CONTROL AND INTERFACE 002aad453 A2 Fig 1. A1 A0 SCL SDA GND Block diagram of LM75B 6. Pinning information 6.1 Pinning SDA 1 8 VCC SCL 2 7 A0 OS 3 6 SDA 1 8 VCC SCL 2 7 A0 A1 OS 3 6 A1 A2 GND 4 5 A2 LM75BD GND 5 4 002aad455 002aad454 Fig 2. LM75BDP Pin configuration for SO8 Fig 3. SDA 1 8 VCC SCL 2 7 A0 OS 3 6 A1 GND 4 5 A2 Pin configuration for TSSOP8 terminal 1 index area LM75BGD SDA 1 SCL 2 LM75B Product data sheet A0 OS 3 6 A1 GND 4 5 A2 002aag155 Fig 5. All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 7 Transparent top view Transparent top view Pin configuration for XSON8U VCC LM75BTP 002aae234 Fig 4. 8 Pin configuration for HWSON8 (c) NXP B.V. 2014. All rights reserved. 4 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 6.2 Pin description Table 3. Pin description Symbol Pin Description SDA 1 Digital I/O. I2C-bus serial bidirectional data line; open-drain. SCL 2 Digital input. I2C-bus serial clock input. OS 3 Overtemperature Shutdown output; open-drain. GND 4 Ground. To be connected to the system ground. A2 5 Digital input. User-defined address bit 2. A1 6 Digital input. User-defined address bit 1. A0 7 Digital input. User-defined address bit 0. VCC 8 Power supply. 7. Functional description 7.1 General operation The LM75B uses the on-chip band gap sensor to measure the device temperature with the resolution of 0.125 C and stores the 11-bit two's complement digital data, resulted from 11-bit A-to-D conversion, into the device Temp register. This Temp register can be read at any time by a controller on the I2C-bus. Reading temperature data does not affect the conversion in progress during the read operation. The device can be set to operate in either mode: normal or shutdown. In normal operation mode, the temp-to-digital conversion is executed every 100 ms and the Temp register is updated at the end of each conversion. During each `conversion period' (Tconv) of about 100 ms the device takes only about 10 ms, called `temperature conversion time' (tconv(T)), to complete a temperature-to-data conversion and then becomes idle for the time remaining in the period. This feature is implemented to significantly reduce the device power dissipation. In shutdown mode, the device becomes idle, data conversion is disabled and the Temp register holds the latest result; however, the device I2C-bus interface is still active and register write/read operation can be performed. The device operation mode is controllable by programming bit B0 of the configuration register. The temperature conversion is initiated when the device is powered-up or put back into normal mode from shutdown. In addition, at the end of each conversion in normal mode, the temperature data (or Temp) in the Temp register is automatically compared with the overtemperature shutdown threshold data (or Tth(ots)) stored in the Tos register, and the hysteresis data (or Thys) stored in the Thyst register, in order to set the state of the device OS output accordingly. The device Tos and Thyst registers are write/read capable, and both operate with 9-bit two's complement digital data. To match with this 9-bit operation, the Temp register uses only the 9 MSB bits of its 11-bit data for the comparison. The way that the OS output responds to the comparison operation depends upon the OS operation mode selected by configuration bit B1, and the user-defined fault queue defined by configuration bits B3 and B4. LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 5 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog In OS comparator mode, the OS output behaves like a thermostat. It becomes active when the Temp exceeds the Tth(ots), and is reset when the Temp drops below the Thys. Reading the device registers or putting the device into shutdown does not change the state of the OS output. The OS output in this case can be used to control cooling fans or thermal switches. In OS interrupt mode, the OS output is used for thermal interruption. When the device is powered-up, the OS output is first activated only when the Temp exceeds the Tth(ots); then it remains active indefinitely until being reset by a read of any register. Once the OS output has been activated by crossing Tth(ots) and then reset, it can be activated again only when the Temp drops below the Thys; then again, it remains active indefinitely until being reset by a read of any register. The OS interrupt operation would be continued in this sequence: Tth(ots) trip, Reset, Thys trip, Reset, Tth(ots) trip, Reset, Thys trip, Reset, etc. Putting the device into the shutdown mode by setting the bit 0 of the configuration register also resets the OS output. In both cases, comparator mode and interrupt mode, the OS output is activated only if a number of consecutive faults, defined by the device fault queue, has been met. The fault queue is programmable and stored in the two bits, B3 and B4, of the Configuration register. Also, the OS output active state is selectable as HIGH or LOW by setting accordingly the configuration register bit B2. At power-up, the device is put into normal operation mode, the Tth(ots) is set to 80 C, the Thys is set to 75 C, the OS active state is selected LOW and the fault queue is equal to 1. The temp reading data is not available until the first conversion is completed in about 100 ms. The OS response to the temperature is illustrated in Figure 6. Tth(ots) Thys reading temperature limits OS reset OS active OS output in comparator mode OS reset (1) (1) (1) OS active OS output in interrupt mode 002aae334 (1) OS is reset by either reading register or putting the device in shutdown mode. It is assumed that the fault queue is met at each Tth(ots) and Thys crossing point. Fig 6. LM75B Product data sheet OS response to temperature All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 6 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 7.2 I2C-bus serial interface The LM75B can be connected to a compatible 2-wire serial interface I2C-bus as a slave device under the control of a controller or master device, using two device terminals, SCL and SDA. The controller must provide the SCL clock signal and write/read data to/from the device through the SDA terminal. Notice that if the I2C-bus common pull-up resistors have not been installed as required for I2C-bus, then an external pull-up resistor, about 10 k, is needed for each of these two terminals. The bus communication protocols are described in Section 7.10. 7.2.1 Bus fault time-out If the SDA line is held LOW for longer than tto (75 ms minimum / 13.3 Hz; guaranteed at 50 ms minimum / 20 Hz), the LM75B will reset to the idle state (SDA released) and wait for a new START condition. This ensures that the LM75B will never hang up the bus should there be conflict in the transmission sequence. 7.3 Slave address The LM75B slave address on the I2C-bus is partially defined by the logic applied to the device address pins A2, A1 and A0. Each of them is typically connected either to GND for logic 0, or to VCC for logic 1. These pins represent the three LSB bits of the device 7-bit address. The other four MSB bits of the address data are preset to `1001' by hard wiring inside the LM75B. Table 4 shows the device's complete address and indicates that up to 8 devices can be connected to the same bus without address conflict. Because the input pins, SCL, SDA and A2 to A0, are not internally biased, it is important that they should not be left floating in any application. Table 4. Address table 1 = HIGH; 0 = LOW. MSB 1 LSB 0 0 1 A2 A1 A0 7.4 Register list The LM75B contains four data registers beside the pointer register as listed in Table 5. The pointer value, read/write capability and default content at power-up of the registers are also shown in Table 5. LM75B Product data sheet Table 5. Register table Register name Pointer value R/W POR state Description Conf 01h R/W 00h Configuration register: contains a single 8-bit data byte; to set the device operating condition; default = 0. Temp 00h read only n/a Temperature register: contains two 8-bit data bytes; to store the measured Temp data. Tos 03h R/W 5000h Overtemperature shutdown threshold register: contains two 8-bit data bytes; to store the overtemperature shutdown Tth(ots) limit; default = 80 C. Thyst 02h R/W 4B00h Hysteresis register: contains two 8-bit data bytes; to store the hysteresis Thys limit; default = 75 C. All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 7 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 7.4.1 Pointer register The Pointer register contains an 8-bit data byte, of which the two LSB bits represent the pointer value of the other four registers, and the other 6 MSB bits are equal to 0, as shown in Table 6 and Table 7. The Pointer register is not accessible to the user, but is used to select the data register for write/read operation by including the pointer data byte in the bus command. Table 6. Pointer register B7 B6 B5 B4 B3 B2 B[1:0] 0 0 0 0 0 0 pointer value Table 7. Pointer value B1 B0 Selected register 0 0 Temperature register (Temp) 0 1 Configuration register (Conf) 1 0 Hysteresis register (Thyst) 1 1 Overtemperature shutdown register (Tos) Because the Pointer value is latched into the Pointer register when the bus command (which includes the pointer byte) is executed, a read from the LM75B may or may not include the pointer byte in the statement. To read again a register that has been recently read and the pointer has been preset, the pointer byte does not have to be included. To read a register that is different from the one that has been recently read, the pointer byte must be included. However, a write to the LM75B must always include the pointer byte in the statement. The bus communication protocols are described in Section 7.10. At power-up, the Pointer value is equal to 00 and the Temp register is selected; users can then read the Temp data without specifying the pointer byte. 7.4.2 Configuration register The Configuration register (Conf) is a write/read register and contains an 8-bit non-complement data byte that is used to configure the device for different operation conditions. Table 8 shows the bit assignments of this register. Table 8. Conf register Legend: * = default value. Bit Symbol Access Value Description B[7:5] reserved R/W B[4:3] OS_F_QUE[1:0] R/W B2 LM75B Product data sheet OS_POL 000* reserved for manufacturer's use; should be kept as zeroes for normal operation OS fault queue programming 00* queue value = 1 01 queue value = 2 10 queue value = 4 11 queue value = 6 R/W OS polarity selection 0* OS active LOW 1 OS active HIGH All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 8 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog Table 8. Conf register ...continued Legend: * = default value. Bit Symbol Access Value Description B1 OS_COMP_INT R/W OS operation mode selection 0* OS comparator 1 B0 SHUTDOWN OS interrupt R/W device operation mode selection 0* normal 1 shutdown 7.4.3 Temperature register The Temperature register (Temp) holds the digital result of temperature measurement or monitor at the end of each analog-to-digital conversion. This register is read-only and contains two 8-bit data bytes consisting of one Most Significant Byte (MSByte) and one Least Significant Byte (LSByte). However, only 11 bits of those two bytes are used to store the Temp data in two's complement format with the resolution of 0.125 C. Table 9 shows the bit arrangement of the Temp data in the data bytes. Table 9. Temp register MSByte LSByte 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 X X X X X When reading register Temp, all 16 bits of the two data bytes (MSByte and LSByte) are provided to the bus and must be all collected by the controller to complete the bus operation. However, only the 11 most significant bits should be used, and the 5 least significant bits of the LSByte are zero and should be ignored. One of the ways to calculate the Temp value in C from the 11-bit Temp data is: 1. If the Temp data MSByte bit D10 = 0, then the temperature is positive and Temp value (C) = +(Temp data) 0.125 C. 2. If the Temp data MSByte bit D10 = 1, then the temperature is negative and Temp value (C) = (two's complement of Temp data) 0.125 C. Examples of the Temp data and value are shown in Table 10. Table 10. LM75B Product data sheet Temp register value 11-bit binary (two's complement) Hexadecimal value Decimal value Value 011 1111 1000 3F8 1016 +127.000 C 011 1111 0111 3F7 1015 +126.875 C 011 1111 0001 3F1 1009 +126.125 C 011 1110 1000 3E8 1000 +125.000 C 000 1100 1000 0C8 200 +25.000 C 000 0000 0001 001 1 +0.125 C 000 0000 0000 000 0 0.000 C 111 1111 1111 7FF 1 0.125 C All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 9 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog Table 10. Temp register value ...continued 11-bit binary (two's complement) Hexadecimal value Decimal value Value 111 0011 1000 738 200 25.000 C 110 0100 1001 649 439 54.875 C 110 0100 1000 648 440 55.000 C For 9-bit Temp data application in replacing the industry standard LM75, just use only 9 MSB bits of the two bytes and disregard 7 LSB of the LSByte. The 9-bit Temp data with 0.5 C resolution of the LM75B is defined exactly in the same way as for the standard LM75 and it is here similar to the Tos and Thyst registers. The only MSByte of the temperature can also be read with the use of a one-byte reading command. Then the temperature resolution will be 1.00 C instead. 7.4.4 Overtemperature shutdown threshold (Tos) and hysteresis (Thyst) registers These two registers, are write/read registers, and also called set-point registers. They are used to store the user-defined temperature limits, called overtemperature shutdown threshold (Tth(ots)) and hysteresis temperature (Thys), for the device watchdog operation. At the end of each conversion the Temp data will be compared with the data stored in these two registers in order to set the state of the device OS output; see Section 7.1. Each of the set-point registers contains two 8-bit data bytes consisting of one MSByte and one LSByte the same as register Temp. However, only 9 bits of the two bytes are used to store the set-point data in two's complement format with the resolution of 0.5 C. Table 11 and Table 12 show the bit arrangement of the Tos data and Thyst data in the data bytes. Notice that because only 9-bit data are used in the set-point registers, the device uses only the 9 MSB of the Temp data for data comparison. Table 11. Tos register MSByte LSByte 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 D8 D7 D6 D5 D4 D3 D2 D1 D0 X X X X X X X Table 12. Thyst register MSByte LSByte 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 D8 D7 D6 D5 D4 D3 D2 D1 D0 X X X X X X X When a set-point register is read, all 16 bits are provided to the bus and must be collected by the controller to complete the bus operation. However, only the 9 most significant bits should be used and the 7 LSB of the LSByte are equal to zero and should be ignored. Table 13 shows examples of the limit data and value. LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 10 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog Table 13. Tos and Thyst limit data and value 11-bit binary (two's complement) Hexadecimal value Decimal value Value 0 1111 1010 0FA 250 +125.0 C 0 0011 0010 032 50 +25.0 C 0 0000 0001 001 1 +0.5 C 0 0000 0000 000 0 0.0 C 1 1111 1111 1FF 1 0.5 C 1 1100 1110 1CE 50 25.0 C 1 1001 0010 192 110 55.0 C 7.5 OS output and polarity The OS output is an open-drain output and its state represents results of the device watchdog operation as described in Section 7.1. In order to observe this output state, an external pull-up resistor is needed. The resistor should be as large as possible, up to 200 k, to minimize the Temp reading error due to internal heating by the high OS sinking current. The OS output active state can be selected as HIGH or LOW by programming bit B2 (OS_POL) of register Conf: setting bit OS_POL to logic 1 selects OS active HIGH and setting bit B2 to logic 0 sets OS active LOW. At power-up, bit OS_POL is equal to logic 0 and the OS active state is LOW. 7.6 OS comparator and interrupt modes As described in Section 7.1, the device OS output responds to the result of the comparison between register Temp data and the programmed limits, in registers Tos and Thyst, in different ways depending on the selected OS mode: OS comparator or OS interrupt. The OS mode is selected by programming bit B1 (OS_COMP_INT) of register Conf: setting bit OS_COMP_INT to logic 1 selects the OS interrupt mode, and setting to logic 0 selects the OS comparator mode. At power-up, bit OS_COMP_INT is equal to logic 0 and the OS comparator is selected. The main difference between the two modes is that in OS comparator mode, the OS output becomes active when Temp has exceeded Tth(ots) and reset when Temp has dropped below Thys, reading a register or putting the device into shutdown mode does not change the state of the OS output; while in OS interrupt mode, once it has been activated either by exceeding Tth(ots) or dropping below Thys, the OS output will remain active indefinitely until reading a register, then the OS output is reset. Temperature limits Tth(ots) and Thys must be selected so that Tth(ots) > Thys. Otherwise, the OS output state will be undefined. LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 11 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 7.7 OS fault queue Fault queue is defined as the number of faults that must occur consecutively to activate the OS output. It is provided to avoid false tripping due to noise. Because faults are determined at the end of data conversions, fault queue is also defined as the number of consecutive conversions returning a temperature trip. The value of fault queue is selectable by programming the two bits B4 and B3 (OS_F_QUE[1:0]) in register Conf. Notice that the programmed data and the fault queue value are not the same. Table 14 shows the one-to-one relationship between them. At power-up, fault queue data = 0 and fault queue value = 1. Table 14. Fault queue table Fault queue data Fault queue value OS_F_QUE[1] OS_F_QUE[0] Decimal 0 0 1 0 1 2 1 0 4 1 1 6 7.8 Shutdown mode The device operation mode is selected by programming bit B0 (SHUTDOWN) of register Conf. Setting bit SHUTDOWN to logic 1 will put the device into shutdown mode. Resetting bit SHUTDOWN to logic 0 will return the device to normal mode. In shutdown mode, the device draws a small current of approximately 1.0 A and the power dissipation is minimized; the temperature conversion stops, but the I2C-bus interface remains active and register write/read operation can be performed. When the shutdown is set, the OS output will be unchanged in comparator mode and reset in interrupt mode. 7.9 Power-up default and power-on reset The LM75B always powers-up in its default state with: * * * * * * Normal operation mode OS comparator mode Tth(ots) = 80 C Thys = 75 C OS output active state is LOW Pointer value is logic 00 (Temp) When the power supply voltage is dropped below the device power-on reset level of approximately 1.0 V (POR) for over 2 s and then rises up again, the device will be reset to its default condition as listed above. LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 12 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 7.10 Protocols for writing and reading the registers The communication between the host and the LM75B must strictly follow the rules as defined by the I2C-bus management. The protocols for LM75B register read/write operations are illustrated in Figure 7 to Figure 12 together with the following definitions: 1. Before a communication, the I2C-bus must be free or not busy. It means that the SCL and SDA lines must both be released by all devices on the bus, and they become HIGH by the bus pull-up resistors. 2. The host must provide SCL clock pulses necessary for the communication. Data is transferred in a sequence of 9 SCL clock pulses for every 8-bit data byte followed by 1-bit status of the acknowledgement. 3. During data transfer, except the START and STOP signals, the SDA signal must be stable while the SCL signal is HIGH. It means that the SDA signal can be changed only during the LOW duration of the SCL line. 4. S: START signal, initiated by the host to start a communication, the SDA goes from HIGH to LOW while the SCL is HIGH. 5. RS: RE-START signal, same as the START signal, to start a read command that follows a write command. 6. P: STOP signal, generated by the host to stop a communication, the SDA goes from LOW to HIGH while the SCL is HIGH. The bus becomes free thereafter. 7. W: write bit, when the write/read bit = LOW in a write command. 8. R: read bit, when the write/read bit = HIGH in a read command. 9. A: device acknowledge bit, returned by the LM75B. It is LOW if the device works properly and HIGH if not. The host must release the SDA line during this period in order to give the device the control on the SDA line. 10. A': master acknowledge bit, not returned by the device, but set by the master or host in reading 2-byte data. During this clock period, the host must set the SDA line to LOW in order to notify the device that the first byte has been read for the device to provide the second byte onto the bus. 11. NA: Not Acknowledge bit. During this clock period, both the device and host release the SDA line at the end of a data transfer, the host is then enabled to generate the STOP signal. 12. In a write protocol, data is sent from the host to the device and the host controls the SDA line, except during the clock period when the device sends the device acknowledgement signal to the bus. 13. In a read protocol, data is sent to the bus by the device and the host must release the SDA line during the time that the device is providing data onto the bus and controlling the SDA line, except during the clock period when the master sends the master acknowledgement signal to the bus. LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 13 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 1 2 3 4 1 0 0 1 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 0 0 0 0 0 0 0 1 A 0 0 0 4 5 6 7 8 9 SCL SDA S A2 A1 A0 W A device address START pointer byte write P configuration data byte device acknowledge device acknowledge Fig 7. D4 D3 D2 D1 D0 A device acknowledge STOP 001aad624 Write configuration register (1-byte data) 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 (next) SCL SDA S 1 0 0 1 A2 A1 A0 W 0 A 0 0 device address 0 0 0 0 1 A RS (next) pointer byte START device acknowledge 1 2 3 4 5 6 7 1 0 0 1 A2 A1 RE-START device acknowledge write 8 9 A0 R A 1 2 3 4 5 6 7 8 9 SCL (cont.) SDA (cont.) D7 D6 D5 D4 D3 D2 D1 D0 NA device address data byte from device STOP master not acknowledged read device acknowledge Fig 8. P 001aad625 Read configuration register including pointer byte (1-byte data) 1 2 3 4 5 6 7 1 0 0 1 A2 A1 8 9 A0 R A 1 2 3 4 5 6 7 8 9 SCL SDA S device address START D7 D6 D5 D4 D3 D2 D1 D0 NA data byte from device read device acknowledge Fig 9. P master not acknowledged STOP 001aad626 Read configuration or temp register with preset pointer (1-byte data) LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 14 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 SCL (next) SDA S 1 0 0 1 A2 A1 A0 W A 0 0 0 device address 0 0 device acknowledge 3 4 P0 (next) A device acknowledge write 2 P1 pointer byte START 1 0 5 6 7 8 9 1 2 3 4 5 6 7 8 9 SCL (cont.) SDA (cont.) D7 D6 D5 D4 D3 D2 D1 D0 A D7 D6 D5 D4 D3 D2 D1 D0 MSByte data A P LSByte data STOP device acknowledge device acknowledge 002aad036 Fig 10. Write Tos or Thyst register (2-byte data) 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 0 SCL SDA (next) S 1 0 0 1 A2 A1 A0 W A 0 0 device address START 0 0 0 0 P1 P0 A RS (next) pointer byte 1 2 3 4 device acknowledge 5 6 7 8 1 0 0 1 A2 A1 A0 R RE-START device acknowledge write 9 A 1 2 3 4 5 6 7 8 1 9 2 3 4 5 6 7 8 9 SCL (cont) SDA (cont) D7 D6 D5 D4 D3 D2 D1 D0 A' device address D7 D6 D5 D4 D3 D2 D1 D0 NA MSByte from device LSByte from device master acknowledge read device acknowledge P STOP master not acknowledged 002aad037 Fig 11. Read Temp, Tos or Thyst register including pointer byte (2-byte data) 1 2 3 4 1 0 0 1 5 6 7 8 9 A2 A1 A0 R A 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 SCL SDA S device address START D7 D6 D5 D4 D3 D2 D1 D0 A' D7 D6 D5 D4 D3 D2 D1 D0 NA MSByte from device read device acknowledge master acknowledge P LSByte from device master not acknowledged STOP 002aad038 Fig 12. Read Temp, Tos or Thyst register with preset pointer (2-byte data) LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 15 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 8. Application design-in information 8.1 Typical application power supply 0.1 F BUS 10 k PULL-UP RESISTORS 10 k SCL I2C-BUS SDA A2 DIGITAL LOGIC 10 k VCC A1 A0 8 2 1 LM75B 3 OS DETECTOR OR INTERRUPT LINE 5 6 7 4 GND 002aad457 Fig 13. Typical application 8.2 LM75A and LM75B comparison Table 15. LM75A and LM75B comparison Description LM75A availability of the XSON8U (3 mm 2 mm) package type no yes OS output auto-reset when SHUTDOWN bit is set in interrupt mode[1] no yes support single-byte reading of the Temp registers without bus lockup[2] no yes no yes bus fault time-out (75 ms, 200 ms)[3] (tHD;DAT)[4] LM75B 10 ns 0 ns ratio of conversion time / conversion period (typical)[5] 100 ms / 100 ms 10 ms / 100 ms supply current in shutdown mode (typical value) 3.5 A 0.2 A HBM ESD protection level (minimum) >2000 V >4500 V minimum data hold time MM ESD protection level (minimum) >200 V >450 V CDM ESD protection level (minimum) >1000 V >2000 V [1] This option is updated to be compatible with the competitive parts. When the OS output has been activated in the interrupt mode due to a temp limit violation, if the Configuration Shutdown bit B0 is set (to the LM75A), then the OS output activated status remains unchanged, while (to the LM75B) the OS will be reset. The latter is compatible with the operation condition of the competitive parts. [2] The LM75 series is intentionally designed to provide two successive temperature data bytes (MSByte and LSByte) for the 11-bit data resolution and both bytes should be read in a typical application. In some specific applications, when only the MSByte is read using a single-byte read command, it often happens that if bit D7 of the LSByte is zero, then the device will hold the SDA bus in a LOW state forever, resulting in a bus hang-up problem, and the bus cannot be released until the device power is reset. This condition exists for the LM75A but not for the LM75B. For the LM75B the temperature can be read either one byte or two bytes without a hang-up problem. [3] The bus time-out is included for releasing the LM75B device operation whenever the SDA input is kept at a LOW state for too long (longer than the LM75B time-out duration) due to a fault from the host. The trade-off for this option is the limitation of the I2C-bus low frequency operation to be limited to 20 Hz. This option is compatible with some of the latest versions of the competitive parts. [4] The data hold time is improved to increase the timing margin in I2C-bus operation. LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 16 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog [5] The LM75B performs the temperature-to-data conversions with a much higher speed than the LM75A. While the LM75A takes almost the whole of conversion period (Tconv) time of about 100 ms to complete a conversion, the LM75B takes only about 110 of the period, or about 10 ms. Therefore, the conversion period (Tconv) is the same, but the temperature conversion time (tconv(T)) is different between the two parts. A shorter conversion time is applied to significantly reduce the device's average power dissipation. During each conversion period, when the conversion is completed, the LM75B becomes idled and the power is reduced, resulting in a lesser average power consumption. 8.3 Temperature accuracy Because the local channel of the temperature sensor measures its own die temperature that is transferred from its body, the temperature of the device body must be stabilized and saturated for it to provide the stable readings. Because the LM75B operates at a low power level, the thermal gradient of the device package has a minor effect on the measurement. The accuracy of the measurement is more dependent upon the definition of the environment temperature, which is affected by different factors: the printed-circuit board on which the device is mounted; the air flow contacting the device body (if the ambient air temperature and the printed-circuit board temperature are much different, then the measurement may not be stable because of the different thermal paths between the die and the environment). The stabilized temperature liquid of a thermal bath will provide the best temperature environment when the device is completely dipped into it. A thermal probe with the device mounted inside a sealed-end metal tube located in consistent temperature air also provides a good method of temperature measurement. If you would like to calculate the effect of self-heating, use Equation 1 below: Equation 1 is the formula to calculate the effect of self-heating: T = R th j-a V DD I DD AV + V OL SDA I OL sin k SDA + V OL EVENT I OL sin k EVENT (1) where: T = Tj Tamb Tj = junction temperature Tamb = ambient temperature Rth(j-a) = package thermal resistance VDD = supply voltage IDD(AV) = average supply current VOL(SDA) = LOW-level output voltage on pin SDA VOL(EVENT) = LOW-level output voltage on pin EVENT IOL(sink)(SDA) = SDA output current LOW IOL(sink)EVENT = EVENT output current LOW Calculation example: Tamb (typical temperature inside the notebook) = 50 C IDD(AV) = 400 A VDD = 3.6 V Maximum VOL(SDA) = 0.4 V IOL(sink)(SDA) = 1 mA LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 17 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog VOL(EVENT) = 0.4 V IOL(sink)EVENT = 3 mA Rth(j-a) = 56 C/W Self heating due to power dissipation is: T = 56 3.6 0.4 + 0.4 3 + 0.4 1 = 56 C W 3.04 mW = 0.17 C (2) 8.4 Noise effect The LM75B device design includes the implementation of basic features for a good noise immunity: * The low-pass filter on both the bus pins SCL and SDA; * The hysteresis of the threshold voltages to the bus input signals SCL and SDA, about 500 mV minimum; * All pins have ESD protection circuitry to prevent damage during electrical surges. The ESD protection on the address, OS, SCL and SDA pins it to ground. The latch-back based device breakdown voltage of address/OS is typically 11 V and SCL/SDA is typically 9.5 V at any supply voltage but will vary over process and temperature. Since there are no protection diodes from SCL or SDA to VCC, the LM75B will not hold the I2C lines LOW when VCC is not supplied and therefore allow continued I2C-bus operation if the LM75B is de-powered. However, good layout practices and extra noise filters are recommended when the device is used in a very noisy environment: * * * * LM75B Product data sheet Use decoupling capacitors at VCC pin. Keep the digital traces away from switching power supplies. Apply proper terminations for the long board traces. Add capacitors to the SCL and SDA lines to increase the low-pass filter characteristics. All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 18 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 9. Limiting values Table 16. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Conditions Min Max Unit VCC supply voltage 0.3 +6.0 V VI input voltage at input pins 0.3 +6.0 V II input current at input pins 5.0 +5.0 mA IO(sink) output sink current on pin OS - 10.0 mA VO output voltage on pin OS 0.3 +6.0 V Tstg storage temperature 65 +150 C Tj junction temperature - 150 C 10. Recommended operating conditions LM75B Product data sheet Table 17. Recommended operating characteristics Symbol Parameter VCC Tamb Conditions Min Typ Max Unit supply voltage 2.8 - 5.5 V ambient temperature 55 - +125 C All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 19 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 11. Static characteristics Table 18. Static characteristics VCC = 2.8 V to 5.5 V; Tamb = 55 C to +125 C; unless otherwise specified. Symbol Parameter Conditions Min Typ[1] Max Unit Tacc temperature accuracy Tamb = 25 C to +100 C 2 - +2 C Tamb = 55 C to +125 C 3 - +3 C Tres temperature resolution 11-bit digital temp data - 0.125 - C tconv(T) temperature conversion time normal mode - 10 - ms Tconv conversion period normal mode - 100 - ms IDD(AV) average supply current normal mode: I2C-bus inactive - 100 200 A - - 300 A I2C-bus normal mode: fSCL = 400 kHz active; shutdown mode - 0.2 1.0 A VIH HIGH-level input voltage digital pins (SCL, SDA, A2 to A0) 0.7 VCC - VCC + 0.3 V VIL LOW-level input voltage digital pins 0.3 - 0.3 VCC V VI(hys) hysteresis of input voltage SCL and SDA pins - 300 - mV A2, A1, A0 pins - 150 - mV IIH HIGH-level input current digital pins; VI = VCC 1.0 - +1.0 A IIL LOW-level input current digital pins; VI = 0 V 1.0 - +1.0 A VOL LOW-level output voltage SDA and OS pins; IOL = 3 mA - - 0.4 V IOL = 4 mA - - 0.8 V ILO output leakage current SDA and OS pins; VOH = VCC - - 10 A Nfault number of faults programmable; conversions in overtemperature-shutdown fault queue 1 - 6 Tth(ots) overtemperature shutdown threshold temperature default value - 80 - C Thys hysteresis temperature default value - 75 - C Ci input capacitance digital pins - 20 - pF [1] Typical values are at VCC = 3.3 V and Tamb = 25 C. LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 20 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 002aae198 300 IDD(AV) (A) 200 IDD(AV) (A) VCC = 5.5 V 4.5 V 3.3 V 2.8 V 100 0 -75 -25 25 75 002aae200 0.5 IDD(sd) (A) 0.4 VCC = 5.5 V 4.5 V 3.3 V 2.8 V 0.3 0 -75 125 Tamb (C) Fig 14. Average supply current versus temperature; I2C-bus inactive 0.3 0.1 0.1 -25 25 75 0 -75 125 Tamb (C) Fig 16. Shutdown mode supply current versus temperature 25 75 125 Tamb (C) 002aae201 0.5 VOL(OS) (V) 0.4 0.2 0 -75 -25 Fig 15. Average supply current versus temperature; I2C-bus active 0.2 0.3 VCC = 5.5 V 4.5 V 3.3 V 2.8 V 200 100 0.5 VOL(SDA) (V) 0.4 002aae199 300 VCC = 5.5 V 4.5 V 3.3 V 2.8 V -25 25 75 125 Tamb (C) Fig 17. LOW-level output voltage on pin OS versus temperature; IOL = 4 mA 002aae202 002aae203 2.0 Tacc (C) VCC = 5.5 V 4.5 V 3.3 V 2.8 V 1.0 0 0.2 -1.0 0.1 0 -75 -25 25 75 125 Tamb (C) Fig 18. LOW-level output voltage on pin SDA versus temperature; IOL = 4 mA LM75B Product data sheet -2.0 -75 -25 25 75 125 Tamb (C) Fig 19. Typical temperature accuracy versus temperature; VCC = 3.3 V All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 21 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 12. Dynamic characteristics Table 19. I2C-bus interface dynamic characteristics[1] VCC = 2.8 V to 5.5 V; Tamb = 55 C to +125 C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit fSCL SCL clock frequency see Figure 20 0.02 - 400 kHz tHIGH HIGH period of the SCL clock 0.6 - - s tLOW LOW period of the SCL clock 1.3 - - s tHD;STA hold time (repeated) START condition 100 - - ns tSU;DAT data set-up time 100 - - ns tHD;DAT data hold time 0 - - ns tSU;STO set-up time for STOP condition 100 - - ns tf fall time - 250 - ns tto time-out time 75 - 200 ms SDA and OS outputs; CL = 400 pF; IOL = 3 mA [2][3] [1] These specifications are guaranteed by design and not tested in production. [2] This is the SDA time LOW for reset of serial interface. [3] Holding the SDA line LOW for a time greater than tto will cause the LM75B to reset SDA to the idle state of the serial bus communication (SDA set HIGH). 0.7 x VDD 0.3 x VDD SDA tLOW tf tSU;DAT tr tHD;STA tSP tf tBUF tr 0.7 x VDD 0.3 x VDD SCL tHD;STA S tHIGH tHD;DAT tSU;STA tSU;STO Sr P S 002aab271 Fig 20. Timing diagram LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 22 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 13. Package outline SO8: plastic small outline package; 8 leads; body width 3.9 mm SOT96-1 D E A X c y HE v M A Z 5 8 Q A2 A (A 3) A1 pin 1 index Lp 1 L 4 e detail X w M bp 0 2.5 5 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z (1) mm 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 5.0 4.8 4.0 3.8 1.27 6.2 5.8 1.05 1.0 0.4 0.7 0.6 0.25 0.25 0.1 0.7 0.3 inches 0.069 0.010 0.057 0.004 0.049 0.01 0.019 0.0100 0.014 0.0075 0.20 0.19 0.16 0.15 0.05 0.01 0.01 0.004 0.028 0.012 0.244 0.039 0.028 0.041 0.228 0.016 0.024 8o o 0 Notes 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT96-1 076E03 MS-012 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-18 Fig 21. Package outline SOT96-1 (SO8) LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 23 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog TSSOP8: plastic thin shrink small outline package; 8 leads; body width 3 mm D E SOT505-1 A X c y HE v M A Z 5 8 A2 pin 1 index (A3) A1 A Lp L 1 4 detail X e w M bp 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D(1) E(2) e HE L Lp v w y Z(1) mm 1.1 0.15 0.05 0.95 0.80 0.25 0.45 0.25 0.28 0.15 3.1 2.9 3.1 2.9 0.65 5.1 4.7 0.94 0.7 0.4 0.1 0.1 0.1 0.70 0.35 6 0 Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 99-04-09 03-02-18 SOT505-1 Fig 22. Package outline SOT505-1 (TSSOP8) LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 24 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog XSON8: plastic extremely thin small outline package; no leads; 8 terminals; body 3 x 2 x 0.5 mm B D SOT996-2 A E A A1 detail X terminal 1 index area e1 1 4 8 5 C C A B C v w b e L1 y y1 C L2 L X 0 1 2 mm scale Dimensions (mm are the original dimensions) Unit(1) mm max nom min A A1 b 0.05 0.35 D E 2.1 3.1 0.5 0.00 0.15 1.9 e e1 0.5 1.5 2.9 L L1 L2 0.5 0.15 0.6 0.3 0.05 0.4 v 0.1 w y 0.05 0.05 y1 0.1 sot996-2_po Outline version References IEC JEDEC JEITA European projection Issue date 07-12-21 12-11-20 SOT996-2 Fig 23. Package outline SOT996-2 (XSON8U) LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 25 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog HWSON8: plastic thermal enhanced very very thin small outline package; no leads; 8 terminals; body 2 x 3 x 0.75 mm SOT1069-2 X B D A A2 A E A1 A3 terminal 1 index area detail X e1 terminal 1 index area e 1 4 C C A B C v w b y y1 C L K E2 8 5 D2 0 1 scale Dimensions Unit mm 2 mm A(1) A1 A2 max 0.80 0.05 0.65 nom 0.75 0.02 0.55 min 0.70 0.00 0.45 A3 b D(1) D2 E(1) E2 0.2 0.30 0.25 0.18 2.1 2.0 1.9 1.6 1.5 1.4 3.1 3.0 2.9 1.6 1.5 1.4 e 0.5 e1 1.5 K L 0.40 0.45 0.35 0.40 0.30 0.35 v 0.1 w y y1 0.05 0.05 0.05 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. References Outline version IEC JEDEC JEITA SOT1069-2 --- MO-229 --- sot1069-2_po European projection Issue date 09-11-18 12-04-18 Fig 24. Package outline SOT1069-2 (HWSON8) LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 26 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 14. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 "Surface mount reflow soldering description". 14.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 14.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: * Through-hole components * Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: * * * * * * Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 14.3 Wave soldering Key characteristics in wave soldering are: * Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave * Solder bath specifications, including temperature and impurities LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 27 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 14.4 Reflow soldering Key characteristics in reflow soldering are: * Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 25) than a SnPb process, thus reducing the process window * Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board * Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 20 and 21 Table 20. SnPb eutectic process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 < 2.5 235 220 2.5 220 220 Table 21. Lead-free process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 25. LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 28 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog temperature maximum peak temperature = MSL limit, damage level minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 25. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 "Surface mount reflow soldering description". LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 29 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 15. Soldering: PCB footprints 5.50 0.60 (8x) 1.30 4.00 6.60 7.00 1.27 (6x) solder lands occupied area placement accuracy 0.25 Dimensions in mm sot096-1_fr Fig 26. PCB footprint for SOT96-1 (SO8); reflow soldering 1.20 (2x) 0.60 (6x) enlarged solder land 0.3 (2x) 1.30 4.00 6.60 7.00 1.27 (6x) 5.50 board direction solder lands occupied area solder resist placement accurracy 0.25 Dimensions in mm sot096-1_fw Fig 27. PCB footprint for SOT96-1 (SO8); wave soldering LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 30 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 3.600 2.950 0.125 0.725 0.125 5.750 3.200 3.600 5.500 1.150 0.600 0.450 0.650 solder lands occupied area Dimensions in mm sot505-1_fr Fig 28. PCB footprint for SOT505-1 (TSSOP8); reflow soldering LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 31 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 2.400 pa + oa 2.000 0.500 0.500 0.250 0.025 0.025 4.250 3.400 pa + oa 2.000 4.000 0.900 solder lands placement area solder paste occupied area Dimensions in mm sot996-2_fr Fig 29. PCB footprint for SOT996-2 (XSON8U); reflow soldering LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 32 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog )RRWSULQWLQIRUPDWLRQIRUUHIORZVROGHULQJRI+:621SDFNDJH 627 *[ ' 3 & Q63[ +\ 63\ *\ 6/\ %\ $\ Q63\ 63[ 6/[ VROGHUODQG VROGHUSDVWHGHSRVLW VROGHUODQGSOXVVROGHUSDVWH RFFXSLHGDUHD ',0(16,216LQPP 3 $\ %\ & ' 6/[ 6/\ 63[ 63\ *[ *\ +\ Q63[ Q63\ ,VVXHGDWH VRWBIU Fig 30. PCB footprint for SOT1069-2 (HWSON8); reflow soldering LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 33 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 16. Abbreviations Table 22. Abbreviations Acronym Description A-to-D Analog-to-Digital CDM Charged-Device Model ESD ElectroStatic Discharge HBM Human Body Model I2C-bus Inter-Integrated Circuit bus I/O Input/Output LSB Lease Significant Bit LSByte Least Significant Byte MSB Most Significant Bit MSByte Most Significant Byte POR Power-On Reset 17. Revision history Table 23. Revision history Document ID Release date Data sheet status Change notice Supersedes LM75B v.5 20140122 Product data sheet - LM75B v.4 Modifications: * Table 1 "Ordering information": added Table note [1] and its reference at LM75BGD. LM75B v.4 20130207 Product data sheet - LM75B v.3 LM75B v.3 20111227 Product data sheet - LM75B v.2 LM75B v.2 20081209 Product data sheet - LM75B v.1 LM75B v.1 20081204 Product data sheet - - LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 34 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 18. Legal information 18.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term `short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 18.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification -- The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 18.3 Disclaimers Limited warranty and liability -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors' aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. LM75B Product data sheet Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer's sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer's applications and products planned, as well as for the planned application and use of customer's third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer's applications or products, or the application or use by customer's third party customer(s). Customer is responsible for doing all necessary testing for the customer's applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer's third party customer(s). NXP does not accept any liability in this respect. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer's general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 35 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog Export control -- This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products -- Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors' warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors' specifications such use shall be solely at customer's own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors' standard warranty and NXP Semiconductors' product specifications. Translations -- A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. 18.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus -- logo is a trademark of NXP B.V. 19. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com LM75B Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 22 January 2014 (c) NXP B.V. 2014. All rights reserved. 36 of 37 LM75B NXP Semiconductors Digital temperature sensor and thermal watchdog 20. Contents 1 2 3 4 4.1 5 6 6.1 6.2 7 7.1 7.2 7.2.1 7.3 7.4 7.4.1 7.4.2 7.4.3 7.4.4 7.5 7.6 7.7 7.8 7.9 7.10 8 8.1 8.2 8.3 8.4 9 10 11 12 13 14 14.1 14.2 14.3 14.4 15 16 17 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 3 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 3 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5 Functional description . . . . . . . . . . . . . . . . . . . 5 General operation . . . . . . . . . . . . . . . . . . . . . . . 5 I2C-bus serial interface . . . . . . . . . . . . . . . . . . . 7 Bus fault time-out . . . . . . . . . . . . . . . . . . . . . . . 7 Slave address . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Register list . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Pointer register . . . . . . . . . . . . . . . . . . . . . . . . . 8 Configuration register . . . . . . . . . . . . . . . . . . . . 8 Temperature register . . . . . . . . . . . . . . . . . . . . 9 Overtemperature shutdown threshold (Tos) and hysteresis (Thyst) registers. . . . . . . 10 OS output and polarity . . . . . . . . . . . . . . . . . . 11 OS comparator and interrupt modes . . . . . . . 11 OS fault queue . . . . . . . . . . . . . . . . . . . . . . . . 12 Shutdown mode . . . . . . . . . . . . . . . . . . . . . . . 12 Power-up default and power-on reset . . . . . . 12 Protocols for writing and reading the registers 13 Application design-in information . . . . . . . . . 16 Typical application . . . . . . . . . . . . . . . . . . . . . 16 LM75A and LM75B comparison . . . . . . . . . . . 16 Temperature accuracy . . . . . . . . . . . . . . . . . . 17 Noise effect. . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 19 Recommended operating conditions. . . . . . . 19 Static characteristics. . . . . . . . . . . . . . . . . . . . 20 Dynamic characteristics . . . . . . . . . . . . . . . . . 22 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 23 Soldering of SMD packages . . . . . . . . . . . . . . 27 Introduction to soldering . . . . . . . . . . . . . . . . . 27 Wave and reflow soldering . . . . . . . . . . . . . . . 27 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 27 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 28 Soldering: PCB footprints. . . . . . . . . . . . . . . . 30 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 34 18 18.1 18.2 18.3 18.4 19 20 Legal information . . . . . . . . . . . . . . . . . . . . . . Data sheet status . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 35 35 35 36 36 37 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'. (c) NXP B.V. 2014. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 22 January 2014 Document identifier: LM75B