LTC4260IUH#TRPBF - Linear Technology Corporation

LTC4260

4260fb

TYPICAL APPLICATION

FEATURES DESCRIPTION

Positive High Voltage

Hot Swap Controller with

I2C Compatible Monitoring

The LTC

4260 Hot Swap™ controller allows a board to be

safely inserted and removed from a live backplane. Using

an external N-channel pass transistor, the board supply

voltage can be ramped up at an adjustable rate. An I2C

interface and onboard ADC allow monitoring of board

current, voltage and fault status.

The device features adjustable analog foldback current

limit with latch off or automatic restart after the LTC4260

remains in current limit beyond an adjustable time-out

delay.

The controller has additional features to interrupt the host

when a fault has occurred, notify when output power is

good, detect insertion of a load card and power-up in

either the on or off state.

APPLICATIONS

n Allows Safe Insertion into Live Backplane

n 8-Bit ADC Monitors Current and Voltage

n I2C™/SMBus Interface

n Wide Operating Voltage Range: 8.5V to 80V

n High Side Drive for External N-Channel MOSFET

n Input Overvoltage/Undervoltage Protection

n Optional Latchoff or Autoretry After Faults

n Alerts Host After Faults

n Foldback Current Limiting

n Available in 24-Lead SO, 24-Lead Narrow

SSOP and 32-Lead (5mm × 5mm) QFN Packages

n Electronic Circuit Breakers

n Live Board Insertion

n Computers, Servers

L, LT, LTC, LTM, Burst Mode, Linear Technology and the Linear logo are registered trademarks

and Hot Swap is a trademark of Linear Technology Corporation. All other trademarks are the

property of their respective owners.

Power Up Waveforms3A, 48V Card Resident Application

BACKPLANE PLUG-IN

CARD

2.67k

1.74k

49.9k

48V

SDA

SCL

ALERT

GND

VDD SENSE

LTC4260

INTVCC

100k

FDB3632

0.010Ω

10Ω

6.8nF

CL43.5k

3.57k

VOUT

48V

24k

68nF

*DIODES INC. SMBT70A

0.1μF

GATE

TIMER GND

BD_PRST

ADIN

GPIO

4260 TA01

SOURCE

SDAO

SDAI

SCL

ALERT

CONNECTOR 1

CONNECTOR 2

VIN

50V/DIV

VOUT

50V/DIV

GPIO

5V/DIV

25ms/DIV 4260 TA02

IIN

2A/DIV

CL = 1000F

LTC4260

4260fb

PIN CONFIGURATION

ABSOLUTE MAXIMUM RATINGS

(Notes 1, 2)

TOP VIEW

GN PACKAGE

24-LEAD PLASTIC SSOP

SENSE

VDD

GND

SCL

SDAI

SDAO

ALERT

TIMER

GATE

SOURCE

GPIO

INTVCC

ADR2

ADR1

ADR0

BD_PRST

ADIN

TJMAX = 125°C, θJA = 85°C/W

TOP VIEW

SW PACKAGE

24-LEAD PLASTIC SO

SENSE

VDD

GND

SCL

SDAI

SDAO

ALERT

TIMER

GATE

SOURCE

GPIO

INTVCC

ADR2

ADR1

ADR0

BD_PRST

ADIN

TJMAX = 125°C, θJA = 75°C/W

32 31 30 29 28 27 26 25

9 10 11 12

TOP VIEW

UH PACKAGE

32-LEAD (5mm × 5mm) PLASTIC QFN

13 14 15 16

1NC

GND

SCL

GPIO

INTVCC

ADR2

VDD

VDDK

SENSE

GATE

SOURCE

SDAI

SDAO

ALERT

TIMER

ADIN

BD_PRST

ADR0

ADR1

TJMAX = 125°C, θJA = 34°C/W

EXPOSED PAD (PIN 33) PCB ELECTRICAL CONNECTION OPTIONAL

ALERT, SDAO ............................................ –0.3V to 6.5V

Supply Voltage (INTVCC) .......................... –0.3V to 6.2V

Operating Temperature Range

LTC4260C ................................................ 0°C to 70°C

LTC4260I.............................................. –40°C to 85°C

Storage Temperature Range

GN, SW Packages ..............................–65°C to 150°C

UH Package ....................................... –65°C to 125°C

Lead Temperature (Soldering, 10 sec)

GN, SW Packages Only ..................................... 300°C

Supply Voltages (VDD) .............................–0.3V to 100V

Input Voltages

SENSE ..............................VDD – 10V or –0.3V to VDD

SOURCE ............................ GATE – 5V to GATE + 0.3V

BD_PRST, FB, ON, OV, UV ...................... –0.3V to 12V

ADR0-ADR2, TIMER, ADIN ........–0.3V to INTVCC + 0.3V

SCL, SDAI ............................................ –0.3V to 6.5V

Output Voltages

GPIO .................................................... –0.3V to 100V

GATE (Note 3) ..................................... –0.3V to 100V

ORDER INFORMATION

LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE

LTC4260CGN#PBF LTC4260CGN#TRPBF LTC4260CGN 24-Lead Plastic SSOP 0°C to 70°C

LTC4260IGN#PBF LTC4260IGN#TRPBF LTC4260IGN 24-Lead Plastic SSOP –40°C to 85°C

LTC4260CSW#PBF LTC4260CSW#TRPBF LTC4260CSW 24-Lead Plastic SO 0°C to 70°C

LTC4260ISW#PBF LTC4260ISW#TRPBF LTC4260ISW 24-Lead Plastic SO –40°C to 85°C

LTC4260CUH#PBF LTC4260CUH#TRPBF 4260 32-Lead (5mm × 5mm) Plastic QFN 0°C to 70°C

LTC4260IUH#PBF LTC4260IUH#TRPBF 4260 32-Lead (5mm × 5mm) Plastic QFN –40°C to 85°C

Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.

For more information on lead free part marking, go to: http://www.linear.com/leadfree/

For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/

LTC4260

4260fb

ELECTRICAL CHARACTERISTICS

SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS

General

VDD Input Supply Range l8.5 80 V

IDD Input Supply Current l25 mA

VDD(UVL) VDD Supply Undervoltage Lockout VDD Falling l7 7.45 7.9 V

INTVCC(UVL) VCC Supply Undervoltage Lockout INTVCC Falling l3.4 3.8 4.2 V

INTVCC Internal Regulator Voltage l5 5.5 6 V

Gate Drive

tDTurn-On Delay l50 100 150 ms

ΔVGATE External N-Channel Gate Drive

(VGATE – VSOURCE)

VDD = 20V to 80V

VDD = 8.5V to 20V

4.5

IGATE(UP) External N-Channel Pull-Up Current Gate Drive On, VGATE = 0V l–14 –18 –22 μA

IGATE(FST) External N-Channel Fast Pull-Down Fast Turn Off, VGATE = 48V, VSOURCE = 43V l300 600 1000 mA

IGATE(DN) External N-Channel Pull-Down Current Gate Drive Off, VGATE = 58V, VSOURCE = 48V l0.7 1 1.4 mA

ISOURCE SOURCE Pin Input Current SOURCE = 48V l200 400 600 μA

Input Pins

VON(TH) ON Pin Threshold Voltage VON Rising l1.19 1.235 1.27 V

ΔVON(HYST) ON Pin Hysteresis l60 130 200 mV

ION(IN) ON Pin Input Current VON = 1.2V l0±1 μA

VOV(TH) OV Pin Threshold Voltage VOV Rising l3.43 3.5 3.56 V

ΔVOV(HYST) OV Pin Hysteresis l70 90 120 mV

IOV(IN) OV Pin Input Current VOV = 3.5V l0±1 μA

VUV(TH) UV Pin Threshold Voltage VUV Rising l3.43 3.5 3.56 V

ΔVUV(HYST) UV Pin Hysteresis l310 380 440 mV

IUV(IN) UV Pin Input Current VUV = 3.5V l0±2 μA

VUV(RTH) UV Pin Reset Threshold Voltage VUV Falling l1.18 1.235 1.27 V

ΔVUV(RHYST) UV Pin Reset Threshold Hysteresis l80 160 250 mV

ΔVSENSE(TH) Current Limit Sense Voltage Threshold

(VDD – VSENSE)

VFB = 3.5V

VFB = 0V

ISENSE(IN) SENSE Pin Input Current VSENSE = 48V l70 100 130 μA

VFB Foldback Pin Power Good Threshold FB Rising l3.43 3.5 3.56 V

ΔVFB(HYST) FB Pin Power Good Hysteresis l80 100 120 mV

IFB Foldback Pin Input Current FB = 3.5V l0±2 μA

VBD_PRST(TH) BD_PRST Input Threshold VBD_PRST Rising l1.2 1.235 1.27 V

ΔVBD_PRST(HYST) BD_PRST Hysteresis l70 130 190 mV

IBD_PRST BD_PRST Pullup Current BD_PRST = 0V l–7 –10 –16 μA

VGPIO(TH) GPIO Pin Input Threshold VGPIO Rising l1.6 1.8 2 V

ΔVGPIO(HYST) GPIO Pin Hysteresis l80 mV

VGPIO(OL) GPIO Pin Output Low Voltage IGPIO = 2mA l0.25 0.5 V

IGPIO(IN) GPIO Pin Input Leakage Current VGPIO = 80V l0±10 μA

RADIN ADIN Pin Input Resistance VADIN = 1.28V l210 MΩ

IADIN ADIN Pin Input Current VADIN = 2.56V l0±1 μA

The l denotes the speciﬁ cations which apply over the full operating

temperature range, otherwise speciﬁ cations are at TA = 25°C. VDD = 48V, unless otherwise noted.

LTC4260

4260fb

ELECTRICAL CHARACTERISTICS

The l denotes the speciﬁ cations which apply over the full operating

temperature range, otherwise speciﬁ cations are at TA = 25°C. VDD = 48V, unless otherwise noted.

SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS

Timer

VTIMER(H) TIMER Pin High Threshold VTIMER Rising l1.2 1.235 1.28 V

VTIMER(L) TIMER Pin Low Threshold VTIMER Falling l0.1 0.2 0.3 V

ITIMER(UP) TIMER Pin Pull-Up Current VTIMER = 0V l–80 –100 –120 μA

ITIMER(DN) TIMER Pin Pull-Down Current VTIMER = 1.3V l1.4 2 2.6 μA

ITIMER(RATIO) TIMER Pin Current Ratio

ITIMER(DN)/ITIMER(UP)

l1.6 2 2.7 %

AC Parameters

tPLH(GATE) Input High (ON) to GATE High

Propagation Delay

CGATE = 1pF l13 μs

tPHL(GATE) Input High (OV, BD_PRST), Input Low

(ON, UV) to GATE Low Propagation Delay

CGATE = 1pF l0.5 3 μs

tPHL(SENSE) (VDD – SENSE) High to GATE Low VDD – SENSE = 200mV, CGATE = 10nF l0.4 1 μs

ADC

Resolution (No Missing Codes) (Note 4) l8 Bits

Integral Nonlinearity VDD – SENSE (Note 5)

SOURCE

ADIN

±0.5

±2

±1.25

LSB

Offset Error VDD – SENSE

SOURCE

ADIN

±1.5

±1

LSB

Full Scale Error (Note 6) l±5 LSB

Total Unadjusted Error (Note 6) l±5 LSB

Full Scale Voltage (Code 255) VDD – SENSE (Note 6)

SOURCE

ADIN

100

2.50

76.5

10.2

2.55

104

2.60

Conversion Rate 10 Hz

I2C Interface

VADR(H) ADR0 to ADR2 Input High Voltage

Threshold

INTVCC

–0.6

INTVCC

–0.45

INTVCC

–0.25

VADR(L) ADR0 to ADR2 Input Low Voltage

Threshold

0.25 0.45 0.65 V

IADR(IN) ADR0 to ADR2 Input Current ADR0 to ADR2 = 0V, 5.5V l–80 80 μA

VSDAI,SCL(TH) SDAI, SCL Input Threshold l1.6 1.8 2 V

ISDAI,SCL(IN) SDAI, SCL Input Current SCL, SDAI = 5V l0±1 μA

VSDAO(OL) SDAO Output Low Voltage ISDAO = 5mA l0.2 0.4 V

VALERT(OL) ALERT Output Low Voltage IALERT = 5mA l0.2 0.4 V

ISDAO,ALERT(IN) SDAO, ALERT Input Current SDAO, ALERT = 5V l0±1 μA

LTC4260

4260fb

ELECTRICAL CHARACTERISTICS

The l denotes the speciﬁ cations which apply over the full operating

temperature range, otherwise speciﬁ cations are at TA = 25°C. VDD = 48V, unless otherwise noted.

SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS

I2C Interface Timing (Note 4)

fSCL(MAX) Maximum SCL Clock Frequency Operates with fSCL ≤ fSCL(MAX) 400 kHz

tBUF(MIN) Minimum Bus Free Time Between

Stop/Start Condition

0.12 1.3 μs

tSU,STA(MIN) Minimum Repeated Start Condition

Set-Up Time

30 600 ns

tHD,STA(MIN) Minimum Hold Time After (Repeated)

Start Condition

140 600 ns

tSU,STO(MIN) Minimum Stop Condition Set-Up Time 30 600 ns

tSU,DAT(MIN) Minimum Data Set-Up Time Input 30 100 ns

tHD,DATI(MIN) Minimum Data Hold Time Input –100 0 ns

tHD,DATO(MIN) Minimum Data Hold Time Output 300 500 900 ns

tSP(MAX) Maximum Suppressed Spike Pulse Width 50 110 250 ns

CXSCL, SDA Input Capacitance SDAI Tied to SDAO 5 10 pF

Note 1: Stresses beyond those listed under Absolute Maximum Ratings

may cause permanent damage to the device. Exposure to any Absolute

Maximum Rating condition for extended periods may affect device

reliability and lifetime.

Note 2: All currents into pins are positive, all voltages are referenced to

GND unless otherwise specified.

Note 3:

Limits on maximum rating is defined as whichever limit occurs first.

An internal clamp limits the GATE pin to a minimum of 10V above source.

Driving this pin to voltages beyond the clamp may damage the device.

Note 4: Guaranteed by design and not subject to test.

Note 5: Integral nonlinearity is defined as the deviation of a code from a

precise analog input voltage. Maximum specifications are limited by the

LSB step size and the single shot measurement. Typical specificatons are

measured from the 1/4, 1/2 and 3/4 areas of the quantization band.

Note 6: For the VDD-sense channel, full-scale is at code 255 but codes

above 200 may be discarded by offset cancellation. Full scale error and

total unadjusted error are evaluated over the 0-200 code range. Full scale

voltage corresponds to the theorectical code 255, and is extrapolated from

a code 200 measurement.

LTC4260

4260fb

TYPICAL PERFORMANCE CHARACTERISTICS

TA = 25°C, VDD = 48V unless otherwise noted.

IDD vs VDD

UV Low-High Threshold

vs Temperature

UV Hysteresis vs Temperature

ON, BDPRST Low-High

Threshold vs Temperature

ON, BDPRST Hysteresis

vs Temperature

INTVCC vs ILOAD

Current Limit Sense Voltage

vs FB Voltage

Current Limit Propagation Delay

vs Sense Voltage

TIMER Pull-Up Current

vs Temperature

VDD (V)

IDD (mA)

2.0

85°C 25°C

2.5

4260 G01

1.5

1.0 20 40 60 100

3.0

–40°C

TEMPERATURE (°C)

–50

3.46

UV LOW-HIGH THRESHOLD (V)

3.48

3.50

3.52

3.54

–25 0 25 50

4260 G02

75 100

TEMPERATURE (°C)

–50

0.34

UV HYSTERESIS (V)

0.35

0.36

0.37

0.38

0.39

–25 02550

4260 G03

75 100

TEMPERATURE (°C)

–50

1.220

ON, BD_PRST LOW-HIGH THRESHOLD (V)

1.225

1.230

1.235

1.240

1.245

–25 02550

4260 G04

75 100

TEMPERATURE (°C)

–50

0.10

ON, BD_PRST HYSTERESIS (V)

0.11

0.12

0.13

0.14

0.16

–25 02550

4260 G05

75 100

0.15

TEMPERATURE (°C)

–50

–90

TIMER PULL-UP CURRENT (μA)

–95

–100

–105

–110

–25 0 25 50

4260 G06

75 100

FB VOLTAGE (V)

CURRENT LIMIT SENSE VOLTAGE (VDD – VSENSE) (mV)

12 34

4260 G07

0.5 1.5 2.5 3.5

CURRENT LIMIT SENSE VOLTAGE (VDD – VSENSE) (mV)

0.1

CURRENT LIMIT PROPAGATION DELAY (μs)

100

1000

50 100 150 200

4260 G08

250 300 350

ILOAD (mA)

0 –2–4–6–8–10

INTVCC (V)

4260 G18

6VDD = 48V

VDD = 12V

MAX ILOAD = 4.5 mA

CAUTION: DRAWING CURRENT

FROM INTVCC INCREASES POWER

DISSIPATION AND TJ

LTC4260

4260fb

TYPICAL PERFORMANCE CHARACTERISTICS

TA = 25°C, VDD = 48V unless otherwise noted.

IGATE Pull Up vs Temperature Gate Drive vs IGATE

Gate Drive vs Temperature

Gate Drive vs VDD

ADC Total Unadjusted Error

vs Code (ADIN Pin)

GPIO VOUT Low vs ILOAD

ADC INL vs Code (ADIN Pin) ADC DNL vs Code (ADIN Pin)

ADC Full-Scale Error

vs Temperature (ADIN Pin)

TEMPERATURE (°C)

–50

–10

IGATE PULL UP (μA)

–15

–20

–25

–25 0 25 50

4260 G09

75 100

IGATE (μA)

GATE DRIVE (VGATE – VSOURCE) (V)

–20

4260 G10

0–5 –10 –15

VDD = 80V

VDD = 48V

VDD = 12V

VDD (V)

GATE DRIVE (VGATE – VSOURCE) (V)

20 30

4260 G11

10 15 25 35

85°C

25°C

–40°C

TEMPERATURE (°C)

–50

GATE DRIVE (VGATE – VSOURCE) (V)

–25 02550

4260 G12

75 100

ILOAD (mA)

030 50

4260 G13

10 20 40 60

GPIO VOUT LOW (V)

CODE

ADC TOTAL UNADJUSTED ERROR (LSB)

256

4260 G14

–1

–2 64 128 192

TEMPERATURE (°C)

–50

–2

ADC FULL-SCALE ERROR (LSB)

–1

–25 0 25 50

3708 G15

75 100

CODE

ADC INL (LSB)

0.25

256

4260 G16

–0.25

–0.50 64 128 192

0.50

CODE

ADC DNL (LSB)

0.25

256

4260 G17

–0.25

–0.50 64 128 192

0.50

LTC4260

4260fb

PIN FUNCTIONS

ADIN: ADC Input. A voltage between 0V and 2.56V applied

to this pin can be measured by the onboard ADC. Tie to

ground if unused.

ADR0 to ADR2: Serial Bus Address Inputs. Tying these

pins to ground, open or INTVCC configures one of 27 pos-

sible addresses. See Table 1 in Applications Information.

ALERT: Fault Alert Output. Open-drain logic output that can

be pulled to ground when a fault occurs to alert the host

controller. A fault alert is enabled by the ALERT register.

This device is compatible with SMBus alert protocol. See

Applications Information. Tie to ground if unused.

BD_PRST: Board Present Input. Ground this pin to en-

able the N-channel FET to turn on after 100ms debounce

delay. When this pin is high, the FET is off. An internal

10μA current source pulls up this pin. Transitions on this

pin will be recorded in the FAULT register. A high-to-low

transition activates the logic to read the state of the ON

pin and clear Faults. See Applications Information.

Exposed Pad (Pin 33, UH Package): Exposed Pad may

be left open or connected to device ground.

FB: Foldback and Power Good Input. A resistive divider

from the output voltage is tied to this pin. When the

voltage at this pin drops below 3.41V, the output power

is considered bad and the current limit is reduced. The

power bad condition can be indicated with the GPIO pin

and a power bad fault can be logged in this condition. See

Applications Information.

GATE: Gate Drive for External N-Channel FET. An internal

18μA current source charges the gate of the external

N-channel MOSFET. A resistor and capacitor network from

this pin to ground sets the turn-on rate and compensates

the active current limit. During turn-off there is a 1mA

pull-down current. During a short circuit or undervoltage

lockout (VDD or INTVCC), a 600mA pull-down current

source between GATE and SOURCE is activated.

GND: Device Ground.

GPIO: General Purpose Input/Output. Open-drain logic

output and logic input. Defaults to pull low to indicate

power is bad. Configure according to Table 3.

NC: No Connect. Unconnected pins. These pins provide

extra distance between high and low voltage pins.

ON: On Control Input. A rising edge turns on the external

N-channel FET and a falling edge turns it off. This pin is

also used to configure the state of the FET ON bit (and

hence the external FET) at power up. For example if the

ON pin is tied high, then the FET ON control bit (A3) will

go high 100ms after power-up. Likewise if the ON pin is

tied low then the part will remain off after power-up until

the FET ON control bit is set high using the I2C bus. A

high-to-low transition on this pin will clear faults.

OV (GN/UH Packages): Overvoltage Comparator Input.

Connect this pin to an external resistive divider from VDD.

If the voltage at this pin rises above 3.5V, an overvoltage

fault is detected and the switch turns off. Tie to GND if

unused.

SCL: Serial Bus Clock Input. Data at the SDA pin is shifted

in or out on rising edges of SCL. This is a high impedance

pin that is generally driven by an open-collector output

from a master controller. An external pull-up resistor or

current source is required.

SDAI: Serial Bus Data Input. A high impedance input used

for shifting in address, command or data bits. Normally

tied to SDAO to form the SDA line.

SDAO: Serial Bus Data Output. Open-drain output used for

sending data back to the master controller or acknowledg-

ing a write operation. Normally tied to SDAI to form the

SDA line. An external pull-up resistor or current source

is required.

LTC4260

4260fb

PIN FUNCTIONS

SENSE: Current Sense Input. Connect this pin to the out-

put of the current sense resistor. The current limit circuit

controls the GATE pin to limit the sense voltage between

the VDD and SENSE pins to 50mV or less depending on

the voltage at the FB pin. This pin is used as an input to

the 8-bit ADC.

SOURCE: N-Channel MOSFET Source Connection and

ADC Input. Connect this pin to the source of the external

N-channel MOSFET switch. This pin also serves as the

ADC input to monitor output voltage. The pin provides a

return for the gate pull-down circuit and as a supply for

the charge pump circuit.

TIMER:

Timer Input. Connect a capacitor between this pin

and ground to set a 12ms/μF duration for current limit

before the switch is turned off. The duration of the off

time is 518ms/μF when autoretry during current limit is

enabled. A minimum value of 0.1nF must be connected

to this pin.

UV: Undervoltage Comparator Input. Connect this pin

to an external resistive divider from VDD. If the voltage

at this pin falls below 3.12V, an undervoltage fault is

detected and the switch turns off. Pulling this pin below

1.2V resets all faults and allows the switch to turn back

on. Tie to INTVCC if unused.

VDD: Supply Voltage and Current Sense Input. This pin

has an undervoltage lockout threshold of 7.45V.

INTVCC: Internal Low Voltage Supply Decoupling Output.

Connect a 0.1μF capacitor from this pin to ground. This

pin can be used to drive the other pins to logic high and

has an undervoltage lockout threshold of 3.8V.

VDDK (UH Package): Same as VDD. Connect this pin to

VDD. VDDK tied to VDD internally with 18Ω.

LTC4260

4260fb

FUNCTIONAL DIAGRAM

–

3.5V

UVS

OVS

RESET

ONS

VDD UVLO

3.5V

1.235V

INTVCC

1.235V

7.45V

SOURCE

I2C

VDD – SENSE

I2C ADDR

–

3.5V –

PWRGD FET ON

–

RST

–

BOARD

PRESENT

–

1.235V –

0.2V

LOGIC

TM2

UVLO2

–

UVLO1

GN/UH ONLY

BD_PRST

10μA

SDAI

SDAO

SCL

ALERT

ADR0 ADR1 ADR2 GND

UH ONLY

EXPOSED

PAD

VDD

ADIN

1 OF 27

3.8V

VCC UVLO

4260 BD

INTVCC

TIMER

GPIO

INTVCC

VDD

100μA

1.8V

2μA

A/D CONVERTER

5.5V

GEN

TM1

SOURCE

GATE

–

VDDK

VDD

18Ω

SENSE

UH ONLY

INTERNAL

POWER CHARGE

PUMP

AND

GATE

DRIVER

FOLDBACK

20mV TO

50mV

+–

LTC4260

4260fb

TIMING DIAGRAM

OPERATION

The Functional Diagram displays the main functional areas

of this device. The LTC4260 is designed to turn a board’s

supply voltage on and off in a controlled manner, allowing

the board to be safely inserted or removed from a live

backplane. During normal operation, the charge pump

and gate driver turn on the external N-channel pass FET’s

gate to pass power to the load. The gate driver uses a

charge pump that derives its power from the SOURCE pin.

When the SOURCE pin is at ground, the charge pump is

powered from an internal 12V supply derived from VDD.

This results in a 200μA current load on the SOURCE pin

when the gate is up. Also included in the gate driver is an

internal 15V gate-to-source clamp.

The current sense (CS) amplifier monitors the load cur-

rent using the difference between the VDD and SENSE pin

voltage. The CS amplifier limits the current in the load by

reducing the GATE-to-SOURCE voltage in an active control

loop. The CS amplifier requires 100μA input bias current

from both the VDD and the SENSE pins.

A short circuit on the output to ground causes significant

power dissipation during active current limiting. To limit

this power, the foldback amplifier reduces the current limit

value from 50mV to 20mV (referred to the VDD minus

SENSE voltage) in a linear manner as the FB pin drops

below 2V (see Typical Performance curves).

If an overcurrent condition persists, the TIMER pin ramps

up with a 100μA current source until the pin voltage

exceeds 1.2V (comparator TM2). This indicates to the

logic that it is time to turn off the pass FET to prevent

overheating. At this point the TIMER pin ramps down us-

ing the 2μA current source until the voltage drops below

tSU, DAT

tSU, STO

tSU, STA tBUF

tHD, STA

tSP

tHD, DATO,

tHD, DATI

tHD, STA

START

CONDITION

STOP

CONDITION

REPEATED START

CONDITION

START

CONDITION

4260 TD01

SDAI/SDAO

SCL

0.2V (comparator TM1) which tells the logic that the pass

transistor has cooled and it is safe to turn it on again.

The output voltage is monitored using the FB pin and the

PG comparator to determine if the power is available for

the load. The power good condition is signalled by the

GPIO pin using an open-drain pull-down transistor. The

GPIO pin can also be used as a general purpose input (GP

comparator) or output pin.

The Functional Diagram shows the monitoring blocks of

the LTC4260. The group of comparators on the left side

includes the UV, OV, RST, BP and ON comparators. These

comparators are used to determine if the external condi-

tions are valid prior to turning on the FET. But first the

two undervoltage lockout circuits UVLO1 and UVLO2 must

validate the input supply and the internally generated 5.5V

supply (INTVCC) and generate the power up initialization

to the logic circuits.

Included in the LTC4260 is an 8-bit A/D converter. The

converter has a 3-input mux to select between the ADIN

pin, the SOURCE pin and the VDD – SENSE voltage.

An I2C interface is provided to read the A/D registers. It also

allows the host to poll the device and determine if faults

have occurred. If the ALERT line is used as an interrupt,

the host can respond to a fault in real time. The typical SDA

line is divided into an SDAI (input) and SDAO (output).

This simplifies applications using an optoisolator driven

directly from the SDAO output. The I2C device address is

decoded using the ADR0, ADR1 and ADR2 pins. These

inputs have three states each that decode into a total of

27 device addresses.

LTC4260

4260fb

The typical LTC4260 application is in a high availability

system that uses a positive voltage supply to distribute

power to individual cards. The device measures card

voltages and currents and records past and present fault

conditions. The system queries each LTC4260 over the

I2C periodically and reads the stored information.

The basic LTC4260 application circuit is shown in Figure 1.

External component selection is discussed in detail in the

Design Example section.

Turn-On Sequence

The power supply on a board is controlled by placing

an external N-channel pass transistor (Q1) in the power

path. Note that sense resistor (RS) detects current and

capacitor C1 controls the GATE slew rate. Resistor R6

compensates the current control loop while R5 prevents

high frequency oscillations in Q1. Resistors R1, R2 and

R3 provide undervoltage and overvoltage sensing.

Several conditions must be present before the external

switch can be turned on. First the external supply VDD must

exceed its undervoltage lockout level. Next the internally

generated supply INTVCC must cross its 4.5V undervoltage

threshold. This generates a 60μs to 120μs power-on-reset

pulse. During reset the fault registers are cleared and the

APPLICATIONS INFORMATION

control registers are set or cleared as described in the

After the power-on-reset pulse, the LTC4260 will go

through the following turn-on sequence. First, the UV and

OV pins must indicate that the input power is within the

acceptable range and the BD⎯PRST pin must be pulled

low. All of these conditions must be satisfied for dura-

tion of 100ms to ensure that any contact bounce during

insertion has ended.

When these initial conditions are satisfied, the ON pin is

checked. If it is high, the external switch turns on. If it

is low, the external switch turns on when the ON pin is

brought high or if a serial bus turn-on command is received.

The switch is turned on by charging up the GATE with a

18μA current source (Figure 2). The voltage at the GATE

pin rises with a slope equal to 18μA/C1 and the supply

inrush current is set at:

IINRUSH =CL

C1 •18μA

When the GATE voltage reaches the FET threshold volt-

age, the switch begins to turn on and the SOURCE voltage

follows the GATE voltage as it increases.

2.67k

1.74k

42 1 24 23

49.9k

Z1*

SMBT70A

VDD SENSE

LTC4260GN

100k

FDB3632

0.010Ω

VIN

48V

10Ω

6.8nF

330μF

43.5k

VOUT

48V

3.57k

100k

0.1μF

GATE

INTVCC ADR0 ADR1

ADR2 GND

BD_PRST

TIMER

ADIN

GPIO

4260 F01

SOURCE

SDAI

SDA0

SCL

ALERT

19 15

0.1μF

17 6

68nF

*DIODES, INC

BACKPLANE PLUG-IN

CARD

SDA

SCL

LERT

GND

CONNECTOR 1

CONNECTOR 2

Figure 1. 5A, 48V Card Resident Application

LTC4260

4260fb

APPLICATIONS INFORMATION

As the SOURCE voltage rises, so will the FB pin which

is monitoring it. If the voltage across the current sense

resistor RS gets too high, the inrush current will then be

limited by the internal current limit circuitry. Once the FB

pin crosses its 3.5V threshold, the GPIO pin, in its default

configuration, will cease to pull low and indicate that the

power is now good.

Turn-Off Sequence

The switch can be turned off by a variety of conditions.

A normal turn-off is initiated by the ON pin going low or

a serial bus turn-off command. Additionally, several fault

conditions will turn off the switch. These include an input

overvoltage (OV pin), input undervoltage (UV pin), over-

current circuit breaker (SENSE pin) or BD⎯PRST going

high. Writing a logic one into the UV, OV or overcurrent

fault bits will also turn off the switch if their autoretry bits

are set to false.

Normally the switch is turned off with a 1mA current pulling

down the GATE pin to ground. With the switch turned off,

the SOURCE voltage drops and when the FB pin crosses

below its threshold, GPIO pulls low to indicate that the

output power is no longer good.

If the VDD pin falls below 7.5V for greater than 5μs or INTVCC

drops below 3.8V for greater than 1μs, a fast shutdown of

the switch is initiated. The GATE pin is pulled down with

a 600mA current to the SOURCE pin.

VDD + 13V

VDD

4260 F02

t1t2

GATE

VOUT

SLOPE = 18μA/C1

Figure 2. Supply Turn-On

Overcurrent Fault

The LTC4260 features an adjustable current limit with fold-

back that protects against short circuits or excessive load

current. To protect against excessive power dissipation in

the switch during active current limit, the available current

is reduced as a function of the output voltage sensed by

the FB pin. The device also features a variable overcurrent

response time. A graph in the Typical Performance curves

shows the delay from a voltage step at the SENSE pin until

the GATE voltage starts falling, as a function of overdrive.

An overcurrent fault occurs when the current limit circuitry

has been engaged for longer than the time-out delay set by

the TIMER pin. Current limiting begins when the current

sense voltage between the VDD and SENSE pins reaches

20mV to 50mV (depending on the foldback). The GATE

pin is then brought down with a 600mA GATE-to-SOURCE

current. The voltage on the GATE is regulated in order

to limit the current sense voltage to less than 50mV. At

this point, a circuit breaker time delay starts by charging

the external timing capacitor from the TIMER pin with a

100μA pull-up current. If the TIMER pin reaches its 1.2V

threshold, the external switch turns off (with a 1mA cur-

rent from GATE to ground). The overcurrent present bit,

C2, and the overcurrent fault bit, D2, are set at this time.

The circuit breaker time delay is given by:

CB = CT • 12 [ms/μF]

After the switch is turned off, the TIMER pin begins

discharging the timing capacitor with a 2μA pull-down

current. When the TIMER pin reaches its 0.2V threshold,

the overcurrent present bit, C2, is cleared, and the switch

will be allowed to turn on again if the overcurrent fault has

been cleared. However, if the overcurrent autoretry bit, A2,

has been set then the switch turns on again automatically

(without resetting the overcurrent fault). Use a minimum

value of 0.1nF for CT.

The waveform in Figure 3 shows how the output latches

off following a short circuit. The drop across the sense

resistor is held at 20mV as the timer ramps up.

LTC4260

4260fb

During a short circuit, if the current limit sense voltage

exceeds 150mV, the active current limit enters a high cur-

rent protection mode that immediately turns off the output

transistor by pulling the GATE-to-SOURCE voltage to zero.

Current in the output transistor drops from tens of amps

to zero in a few hundred nanoseconds. The input voltage

will drop during the high current and then spike upwards

due to parasitic inductances when the FET shuts off (see

Supply Transients). Following this event, the part may turn

on again after a delay (typically the 100ms normal turn-on

delay if the input voltage drops below the UVLO threshold)

and enters active current limit before shutting off.

Overvoltage Fault

An overvoltage fault occurs when the OV pin rises above

its 3.5V threshold. This shuts off the switch immediately

(with a 1mA current from GATE to ground) and sets the

overvoltage present bit, C0, and the overvoltage fault

bit D0. If the OV pin subsequently falls back below the

threshold for 100ms, the switch will be allowed to turn on

again unless the overvoltage autoretry has been disabled

by clearing bit A0.

Undervoltage Fault

An undervoltage fault occurs when the UV pin falls below

its 3.12V threshold. This turns off the switch immediately

(with a 1mA current from GATE to ground) and sets the

undervoltage present bit, C1, and the undervoltage fault

bit D1. If the UV pin subsequently rises above the thresh-

old for 100ms, the switch will turn on again unless the

APPLICATIONS INFORMATION

VOUT

50V/DIV

IOUT

5A/DIV

ΔVGATE

10V/DIV

TIMER

2V/DIV

100μs/DIV 4260 F03

Figure 3. Short-Circuit Waveforms

undervoltage autoretry has been disabled by clearing bit

A1. When power is applied to the device, if UV is below its

3.12V threshold after INTVCC crosses its 4.5V undervoltage

lockout threshold, an undervoltage fault will be logged in

the fault register.

Board Present Change of State

Whenever the BD⎯PRST pin toggles, bit D4 is set to

indicate a change of state. When the BD⎯PRST pin goes

high, indicating board removal, the switch turns off im-

mediately (with a 1mA current from GATE to ground) and

clears the board present bit, C4. If the BD⎯PRST pin is

pulled low, indicating a board insertion, all fault bits except

D4 will be cleared and the board present bit, C4, is set. If

the BD⎯PRST pin remains low for 100ms the state of the

ON pin will be captured in the FET On Control bit A3. This

turns the switch on if the ON pin is tied high. There is an

internal 10μA pull-up current source on the BD⎯PRST pin.

If the system shuts down due to a fault, it may be desirable

to restart the system simply by removing and reinserting

a load card. In cases where the LTC4260 and the switch

reside on a backplane or midplane and the load resides

on a plug-in card, the BD⎯PRST pin can be used to detect

when the plug-in card is removed (see Figure 4). Once

the plug-in card is reinserted the fault register is cleared

(except for D4). After 100ms the state of the ON pin is

latched into bit A3 of the control register. At this point the

system will start up again.

If a connection sense on the plug-in card is driving the

BD⎯PRST

pin, the insertion or removal of the card may

cause the pin voltage to bounce. This will result in clear-

ing the fault register when the card is removed. The pin

can be debounced using a filter capacitor, C

BD⎯PRST

, on

the

BD⎯PRST

pin as shown in Figure 4. The filter time

is given by:

FILTER =

BD⎯PRST • 123 [ms/μF]

FET Short Fault

A FET short fault will be reported if the data converter

measures a current sense voltage greater than or equal

to 2mV while the FET is turned off. This condition sets the

FET short present bit, C5, and the FET short fault bit D5.

LTC4260

4260fb

APPLICATIONS INFORMATION

Power Bad Fault

A power bad fault will be reported if the FB pin drops be-

low its 3.41V threshold while the FET is on. This pulls the

GPIO pin low immediately, when configured as PWRGD,

and sets the power bad present bit, C3, and the power

bad fault bit D3. A circuit will prevent a power bad fault

if the GATE-to-SOURCE voltage is low, eliminating false

power bad faults during power-up or power-down. If the

FB pin subsequently rises back above the threshold, the

GPIO pin will return to a high impedance state and bit C3

will be cleared.

Fault Alerts

When any of the fault bits in FAULT register D are set,

an optional I2C bus alert can be generated by setting the

appropriate bit in the ALERT register B. This allows only

selected faults to generate alerts. At power-up the default

state is to not alert on faults. If an alert is enabled, the cor-

responding fault will cause the ALERT pin to pull low. After

the bus master controller broadcasts the Alert Response

Address, the LTC4260 responds with its address on the

SDA line and releases ALERT as shown in Figure 11. If

there is a collision between two LTC4260s responding

with their addresses simultaneously, then the device with

the lower address wins arbitration and responds first. The

ALERT line will also be released if the device is addressed

by the bus master.

–

1.235V

GND

MOTHERBOARD CONNECTOR PLUG-IN

CARD

SOURCE

OUT

LTC4260

10μA

BD_PRST 14

CBD_PRST

LOAD

4260 F04

Figure 4. Plug-In Card Insertion/Removal

Once the ALERT signal has been released for one fault,

it will not be pulled low again until the FAULT register

indicates a different fault has occurred or the original

fault is cleared and it occurs again. Note that this means

repeated or continuing faults will not generate alerts until

the associated FAULT register bit has been cleared.

Resetting Faults

Faults are reset with any of the following conditions. First,

a serial bus command writing zeros to the FAULT register

D will clear the associated faults. Second, the entire FAULT

the ON pin or bit A3 going from high to low, or if the UV

pin is brought below its 1.23V reset threshold, or if INTVCC

falls below its 3.8V undervoltage lockout threshold. Finally,

when BD⎯PRST is brought from high to low, only FAULT

bits D0-D3 and D5 are cleared, the bit D4 that indicates a

BD⎯PRST change of state will be set. Faults that are still

present (as indicated in the STATUS Register C) cannot

be cleared.

The FAULT register will not be cleared when autoretrying.

When autoretry is disabled the existence of a D0, D1 or D2

fault keeps the switch off. As soon as the fault is cleared,

the switch will turn on. If autoretry is enabled, then a high

value in C0, C1 or C2 will hold the switch off and the FAULT

C2 bits are cleared, the switch is allowed to turn on again.

Data Converter

The LTC4260 incorporates an 8-bit data converter that con-

tinuously monitors three different voltages. The SOURCE

pin uses a 1/40 resistive divider to monitor a full-scale

voltage of 102.4V with 0.4V resolution (divider converts

102.4V to 2.56V). The ADIN pin is monitored with a 2.56V

full scale and 10mV resolution, and the voltage between

the VDD and SENSE pins is monitored with a 76.8mV full

scale and 300μV resolution.

The results from each conversion are stored in registers

E, F and G and are updated 10 times per second. Setting

CONTROL register bit A5 invokes a test mode that halts

the data converter updates so that registers E, F and G

can be written to and read from for software testing.

LTC4260

4260fb

APPLICATIONS INFORMATION

Gate Pin Voltage

A curve of gate drive vs VDD is shown in the Typical Per-

formance curves. At the minimum input supply voltage

of 8.5V, the minimum gate drive voltage is 4.5V. When

the input supply voltage is higher than 20V, the gate

drive is at least 10V and a regular N-FET can be used. In

applications over a 8.5V to 20V range, a logic level N-FET

must be used to maintain adequate gate enhancement.

The GATE pin is clamped at a typical value of 15V above

the SOURCE pin.

Configuring the GPIO Pin

Table 3 describes the possible states of the GPIO pin us-

ing the control register bits A6 and A7. At power-up, the

default state is for the GPIO pin to go high impedance

when power is good (FB pin greater than 3.5V). Other uses

for the GPIO pin are to pull down when power is good,

a general purpose output and a general purpose input.

Compensating the Active Current Loop

The active current limit circuit is compensated using the

resistor R6 and the slew rate capacitor C1. The value for

C1 is calculated to limit the inrush current. The suggested

value for R6 is 100k. This value should work for most pass

FETs (Q1). If the gate capacitance of Q1 is very small then

the best method to compensate the loop is to add a ≈10nF

capacitor between the GATE and SOURCE terminals.The

addition of 10Ω resistor (R5) prevents self-oscillation in

Q1 by isolating trace capacitance from the FET's GATE

Terminal. Locate the gate resistor at, or close to, the body

of the MOSFET.

Supply Transients

The LTC4260 is designed to ride through supply transients

caused by load steps. If there is a shorted load and the

parasitic inductance back to the supply is greater than

0.5μH, there is a chance that the supply could collapse

before the active current limit circuit brings down the

GATE pin. In this case the undervoltage monitors turn

off the pass FET. The undervoltage lockout circuit has a

5μs filter time after VDD drops below 7.5V. The UV pin

reacts in 2μs to shut the GATE off, but it is recommended

to add a filter capacitor CF to prevent unwanted shutdown

caused by short transient. Eventually either the UV pin or

the undervoltage lockout responds to bring the current

under control before the supply completely collapses.

Supply Transient Protection

The LTC4260 is 100% tested and guaranteed to be safe from

damage with supply voltages up to 100V. However, spikes

above 100V may damage the part. During a short-circuit

condition, the large change in currents flowing through the

power supply traces can cause inductive voltage spikes

which could exceed 100V. To minimize the spikes, the

power trace inductance should be minimized by using

wider traces or heavier trace plating. Adding a snubber

circuit will dampen the voltage spikes. It is built using a

100Ω resistor in series with a 0.1μF capacitor between

VDD and GND. A surge suppressor, Z1 in Figure 1, at the

input will clamp the voltage spikes.

Design Example

As a design example, take the following specifications:

VIN = 48V, IMAX = 5A, IINRUSH = 1A, CL= 330μF, VUVON

= 43V, VUVOFF = 38.5V, VOVOFF = 70V, VPWRGDUP = 46V,

VPWRGDDN = 45V and I2CADDRESS = 1010011. The selec-

tion of the sense resistor, RS, is set by the overcurrent

threshold of 50mV:

RS=50mV

IMAX

=50mV

5A =0.010Ω

The FET should be sized to handle the power dissipation

during the inrush charging of the output capacitor COUT.

The method used to determine the power is the principle:

C = Energy in CL= Energy in Q1

Thus:

C = 1/2 CV2 = 1/2(0.33mF)(48V)2 = 0.38J

Calculate the time it takes to charge up COUT:

tCHARGUP =CL•V

IINRUSH

=330μF • 48V

1A =16ms

The average power dissipated in the FET:

LTC4260

4260fb

APPLICATIONS INFORMATION

DISS =EC

tCHARGUP

=0.38J

16ms ≅24W

The SOA (safe operating area) curves of candidate FETs

must be evaluated to ensure that the heat capacity of the

package can stand 24W for 16ms. The SOA curves of the

Fairchild FDB3632 provide for 1A at 50V (50W) for 10ms,

satisfying the requirement.

The inrush current is set to 1A using C1:

C1=CL

IGATE(UP)

IINRUSH

=0.33mF 18μA

1A =5.9nF

Default values of R5 = 10Ω and R6 = 100k are chosen as

discussed previously.

The power dissipated in the FET during overcurrent must

be limited. The active current limit uses a timer to prevent

excessive energy dissipation in the FET. The worst-case

power occurs when the voltage versus current profile of

the foldback current limit is at the maximum. This occurs

when the current is 5A and the voltage is 1/2 of the 48V

or 24V. See the Current Limit Sense Voltage vs FB Voltage

in the Typical Performance curves to view this profile. In

order to survive 120W, the FET SOA curve dictates the

maximum time at this power level. This particular FET

allows 300W at 1ms or less. Therefore, it is acceptable

to set the current limit timeout using CT to be 0.81ms:

CT=0.81ms

12 ms/μF

[]

=68nF

Note the minimum value for CT is 0.1nF.

Choose R1, R2, R3, R7 and R8 for the UV, OV and PG

threshold voltages:

VOVRISING = 71.2V, VOVFALLING = 69.44V (using VOV(TH) =

3.5V rising and 3.41V falling)

VUVRISING = 43V, VUVFALLING = 38.5V, (using VUV(TH) =

3.5V rising and 3.12V falling)

VPGRISING = 46.14V, VPGFALLING = 45V, (using VFB = 3.5V

rising and 3.411V falling)

In addition a 0.1μF ceramic bypass capacitor is placed on

the INTVCC pin. The complete circuit is shown in Figure 1.

Layout Considerations

To achieve accurate current sensing, a Kelvin connection

is recommended. The minimum trace width for 1oz cop-

per foil is 0.02” per amp to make sure the trace stays at

a reasonable temperature. Using 0.03” per amp or wider

is recommended. Note that 1oz copper exhibits a sheet

resistance of about 530μΩ/square. Small resistances add

up quickly in high current applications. To improve noise

immunity, put the resistive divider to the UV, OV and FB

pins close to the device and keep traces to VDD and GND

short. It is also important to put C3, the bypass capacitor

for the INTVCC pin, as close as possible between INTVCC

and GND. A 0.1μF capacitor from the UV pin (and OV pin

through resistor R2) to GND also helps reject supply noise.

Figure 5 shows a layout that addresses these issues. Note

that a surge suppressor, Z1, is placed between supply and

ground using wide traces.

SENSE

LTC4260

VDD

SENSE RESISTOR RS

ILOAD

VIN

GND ILOAD

4260 F05

GND INTVCC

Figure 5. Recommended Layout for

R1, R2, R3, R8, CF, C3, Z1 and RS

LTC4260

4260fb

Digital Interface

The LTC4260 communicates with a bus master using

a 2-wire interface compatible with the I2C bus and the

SMBus, an I2C extension for low power devices.

The LTC4260 is a read-write slave device and supports

SMBus bus Read Byte, Write Byte, Read Word and Write

Word commands. The second word in a Read Word com-

mand will be identical to the first word. The second word

in a Write Word command is ignored. The data formats

for these commands are shown in Figures 6 to10.

Using Optoisolators with SDA

The LTC4260 separates the SDA line into SDAI and SDAO.

If optoisolators are not used then tie SDAI and SDAO

together to construct a normal SDA line. When using

optoisolators connect the SDAI to the output of the incom-

ing opto and connect the SDAO to the input of the out-

going opto (see Figure 13).

START and STOP Conditions

When the bus is idle, both SCL and SDA must be high

(Figure 6). A bus master signals the beginning of a

transmission with a START condition by transitioning SDA

from high to low while SCL is high. When the master has

finished communicating with the slave, it issues a STOP

condition by transitioning SDA from low to high while SCL

is high. The bus is then free for another transmission.

I2C Device Addressing

Twenty-seven distinct bus address are configurable us-

ing the three-state ADR0-ADR2 pins. Table 1 shows the

correspondence between pin states and addresses. Note

that address bits B7 and B6 are internally configured to

10. In addition, the LTC4260 will respond to two special

addresses. Address (1011 111)b is a mass write used to

write to all LTC4260, regardless of their individual address

settings. The mass write can be masked by setting register

bit A4 to zero. Address (0001 100)b is the SMBus Alert

Response Address. If the LTC4260 is pulling low on the

ALERT pin, it will acknowledge this address using the

SMBus Alert Response Protocol.

APPLICATIONS INFORMATION

Acknowledge

The acknowledge signal is used for handshaking between

the transmitter and the receiver to indicate that the last byte

of data was received. The transmitter always releases the

SDA line during the acknowledge clock pulse. When the

slave is the receiver, it must pull down the SDA line so that

it remains LOW during this pulse to acknowledge receipt

of the data. If the slave fails to acknowledge by leaving

SDA HIGH, then the master can abort the transmission by

generating a STOP condition. When the master is receiving

data from the slave, the master must pull down the SDA

line during the clock pulse to indicate receipt of the data.

After the last byte has been received the master will leave

the SDA line HIGH (not acknowledge) and issue a STOP

condition to terminate the transmission.

Write Protocol

The master begins communication with a START condition

followed by the seven bit slave address and the R/W bit set

to zero (Figure 7). The addressed LTC4260 acknowledges

this and then the master sends a command byte which

indicates which internal register the master wishes to write.

The LTC4260 acknowledges this and then latches the lower

three bits of the command byte into its internal Register

Address pointer. The master then delivers the data byte

and the LTC4260 acknowledges once more and latches the

data into its internal register. The transmission is ended

when the master sends a STOP condition. If the master

continues sending a second data byte, as in a Write Word

command, the second data byte will be acknowledged by

the LTC4260 but ignored (Figure 8).

Read Protocol

The master begins a read operation with a START condition

followed by the seven bit slave address and the R/W bit set

to zero (Figure 9). The addressed LTC4260 acknowledges

this and then the master sends a command byte that in-

dicates which internal register the master wishes to read.

The LTC4260 acknowledges this and then latches the lower

three bits of the command byte into its internal Register

Address pointer. The master then sends a repeated START

condition followed by the same seven bit address with the

LTC4260

4260fb

APPLICATIONS INFORMATION

R/W bit now set to one. The LTC4260 acknowledges and

sends the contents of the requested register. The transmis-

sion is ended when the master sends a STOP condition.

If the master acknowledges the transmitted data byte, as

in a Read Word command (Figure 12), the LTC4260 will

repeat the requested register as the second data byte.

Note that the Register Address pointer is not cleared at

the end of the transaction. Thus the Receive Byte protocol

can be used to repeatedly read a specific register.

Alert Response Protocol

The LTC4260 implements the SMBus Alert Response Pro-

tocol as shown in Figure 11. If enabled to do so through

the ALERT register B, the LTC4260 will respond to faults

by pulling the ALERT pin low. Multiple LTC4260s can

share a common ALERT line and the protocol allows a

master to determine which LTC4260s are pulling the line

low. The master begins by sending a START bit followed

by the special Alert Response Address (0001 100)b with

the R/W bit set to one. Any LTC4260 that is pulling its

ALERT pin low will acknowledge and begin sending back

its individual slave address.

An arbitration scheme ensures that the LTC4260 with the

lowest address will have priority; all others will abort their

response. The successful responder will then release its

ALERT pin while any others will continue to hold their

ALERT pins low. Polling may also be used to search for

any LTC4260 that have detected faults. Any LTC4260 pull-

ing its ALERT pin low will also release it if it is individually

addressed during a read or write transaction.

The ALERT signal will not be pulled low again until the

FAULT register indicates a different fault has occurred or the

original fault is cleared and it occurs again. Note that this

means repeated or continuing faults will not generate alerts

until the associated FAULT register bit has been cleared.

SCL

SDA

START

CONDITION

STOP

CONDITION

ADDRESS R/WACK DATA ACK DATA ACK

1 - 7 8 9

4260 F06

a6 - a0 b7 - b0 b7 - b0

1 - 7 8 9 1 - 7 8 9

Figure 6. Data Transfer Over I2C or SMBus

LTC4260

4260fb

APPLICATIONS INFORMATION

Figure 7. LTC4260 Serial Bus SDA Write Byte Protocol

Figure 8. LTC4260 Serial Bus SDA Write Word Protocol

Figure 9. LTC4260 Serial Bus SDA Read Byte Protocol

Figure 10. LTC4260 Serial Bus SDA Read Word Protocol

Figure 11. LTC4260 Serial Bus SDA Alert Response Protocol

S ADDRESS

1 0 a4:a0

4260 F07

FROM MASTER TO SLAVE

FROM SLAVE TO MASTER

A: ACKNOWLEDGE (LOW)

A: NOT ACKNOWLEDGE (HIGH)

R: READ BIT (HIGH)

W: WRITE BIT (LOW)

S: START CONDITION

P: STOP CONDITION

COMMAND DATA

X X X X X b2:b00

000b7:b0

A A AP

S ADDRESS

1 0 a4:a0

COMMAND DATA DATA

X X X X X b2:b00

000 0

4260 F08

X X X X X X X Xb7:b0

AA A AP

S ADDRESS

1 0 a4:a0 1 0 a4:a0 1 0

COMMAND S ADDRESS R A

b7:b0 1

DATA

X X X X X b2:b00

4260 F09

A A AP

S ADDRESS

1 0 a4:a0 1 0 a4:a0 1 0

COMMAND S ADDRESS R A

b7:b0 1

DATA

X X X X X b2:b00

4260 F10

b7:b0

DATA

AAP

ALERT

RESPONSE

ADDRESS

0 0 0 1 1 0 0

DEVICE

ADDRESS

1 0 a4:a00 11

4260 F11

AAP

LTC4260

4260fb

APPLICATIONS INFORMATION

Table 1. LTC4260 I2C Device Addressing

DESCRIPTION

HEX DEVICE

ADDRESS BINARY DEVICE ADDRESS

LTC4260

ADDRESS PINS

h 6543210R/WADR2 ADR1 ADR0

Mass Write BE 1 0 111110 X X X

Alert Response 19 0 0 011001 X X X

0 80 1000000X L NC L

1 82 1000001X L H NC

2 84 1000010X L NC NC

3 86 1000011X L NC H

4 88 1000100X L L L

5 8A 1000101X L H H

6 8C 1000110X L L NC

7 8E 1000111X L L H

8 90 1001000XNC NC L

9 92 1001001XNC H NC

10 94 1001010XNC NC NC

11 96 1001011XNC NC H

12 98 1001100XNC L L

13 9A 1001101XNC H H

14 9C 1001110XNC L NC

15 9E 1001111XNC L H

16 A0 1010000X H NC L

17 A2 1010001X H H NC

18 A4 1010010X H NC NC

19 A6 1010011X H NC H

20 A8 1010100X H L L

21 AA 1010101X H H H

22 AC 1010110X H L NC

23 AE 1010111X H L H

24 B0 1011000X L H L

25 B2 1011001XNC H L

26 B4 1011010X H H L

LTC4260

4260fb

APPLICATIONS INFORMATION

Table 2. LTC4260 Register Addresses and Contents

ADDRESS*

NAME READ/WRITE DESCRIPTION

00h CONTROL (A) R/W Controls Whether the Part Retries After Faults, Set the Switch State

01h ALERT (B) R/W Controls Whether the ALERT Pin is Pulled Low After a Fault is Logged in the Fault Register

02h STATUS (C) R System Status Information

03h FAULT (D) R/W Fault Log

04h SENSE (E) R/W** ADC Current Sense Voltage Data

05h SOURCE (F) R/W** ADC SOURCE Voltage Data

06h, 07h ADIN (G) R/W** ADC ADIN Voltage Data

*Register address MSBs b7-b3 are ignored.

**Writable if bit A5 set.

Table 3. CONTROL Register A (00h)—Read/Write

BIT NAME OPERATION

A7:6 GPIO Configure Configures Behavior of GPIO Pin

FUNCTION A6 A7 GPIO PIN

Power Good (Default) 0 0 GPIO = C3

Power Bad 0 1 GPIO = C3

General Purpose Output 1 0 GPIO = B6

General Purpose Input 1 1 GPIO = Hi-Z

A5 Test Mode Enable Test Mode Halts ADC Operation and Enables Writes to ADC Registers

1 = Enable Test Mode, 0 = Disable Test Mode (Default)

A4 Mass Write Enable Enables Mass Write Using Address (1011 111)b

1 = Enable Mass Write (Default), 0 = Disable Mass Write

A3 FET On Control Turns FET On and Off

1 = Turn FET On, 0 = Turn FET Off. Defaults to ON Pin State at End of Debounce Delay

A2 Overcurrent Autoretry Enables Autoretry After an Overcurrent Fault

1 = Retry Enabled, 0 = Retry Disabled (Default)

A1 Undervoltage Autoretry Enables Autoretry After an Undervoltage Fault

1 = Retry Enabled (Default), 0 = Retry Disabled

A0 Overvoltage Autoretry Enables Autoretry After an Overvoltage Fault

1 = Retry Enabled (Default), 0 = Retry Disabled

LTC4260

4260fb

APPLICATIONS INFORMATION

Table 4. ALERT Register B (01h)—Read/Write

BIT NAME OPERATION

B7 Reserved Not Used

B6 GPIO Output Output Data Bit to GPIO Pin When Configured as Output. Defaults to 0

B5 FET Short Alert Enables Alert for FET Short Condition