Hall Effect Sensors Flange Mount > 55100 55100 Miniature Flange Mounting Proximity Sensor Description The 55100 is a miniature flange mounting hall effect sensor 25.5mm (1.004") x 11.00m (0.433") and only 3.00mm (0.118") high with a choice of digital or programmable analogue outputs. It is available as three-wire (voltage output) or two-wire (current output) versions. It's case design enables screw or adhesive mounting and capable of switching up to 28Vdc and 20mA. It comes with a range of sensitivity, cable length and connector options. Features * Magnetically operated position sensor * Digital or programmable analog types available * Medium, high or programmable sensitivities * Three-wire (voltage output) or twowire (current output) versions Dimensions Dimensions in mm (inch) 11.00 (.433) 3.00 (.118) Excluding encapsulant Benefits 300 (11.81) 25.50 (1.004) * High switching speed up to 10kHz * Long life - up to 20 billion operations * Unaffected by harsh environments 6.35 NOM. (.250) 7.50 (.295) 16.60 (.654) Center of Sensitivity 3.30x4.20 TYP. SLOT (.130X.165) 1.50 (.059) * Open Drain Output * Reverse/Over voltage protection * Built in temperature compensation * Vibration 50g max. @ 50-2,000Hz * Shock 150g max. @ 11ms 1/2 Sine * Operates in static or dynamic magnetic field * Customer selection of cable length and connector type Applications (2.00) * Position and limit sensing * RPM measurement * Flow metering Note: Two-wire version illustrated. * Commutaion of brushless dc motors * Angle sensing * Magnetic encoders Block Diagram Two-wire Version VDD Pin 1 (Red) Cn Hall Plate Switch Comparator Current Source Clock GND Pin 2 (Black) Three-wire Version VDD Pin 1 (Red) Cn VDD Hall Plate Switch Comparator Clock GND Pin 2 (Black) Output Rpu OUT Pin 3 (Blue) Notes: 1. Add capcitor Cn as shown, close to the sensor , for transient suppression if required. 2. Add pull-up resistor Rpu as shown for sinking output. The Rpu value should be calculated using your supply voltage while keeping the ON state current at a level below the maximum. Rpu = VDD/Io; Rpu = 12Vdc/10mA = 1.2kOhm (c) 2015 Littelfuse Revised: 11/02/15 Specifications are subject to change without notice. littelfuse.com Hall Effect Sensors Flange Mount > 55100 55100 Miniature Flange Mounting Proximity Sensor Electrical Ratings Digital Switch Three-Wire (Voltage Output) Digital Switch Two-Wire (Current Output) Vdc Vdc Vdc - max. -15 to +28 +3.8 to +24 32 -15 to +28 +3.75 to +24 32 8.5 4.5 - 5.5 19.5 Output High Voltage Vdc - min. Sinking output N/A 4.65 Output Low Voltage Vdc - max. 0.4 @ 20mA N/A 0.35 Output Current (continuously on) mA - max. 20 N/A -1.0 to +1.0 mA - min. mA - max. 1.6 - 5.2 1.6 - 5.2 5.0 - 6.9 12.0 - 17.0 2.0 - 10.0 2.0 - 10.0 kHz - max 10 10 2 C -40 to +100 -40 to +100 -40 to +100 Hall Type Supply Voltage 1 Absolute Ratings Operate Overvoltage Protection Current Consumption Over Temperature Range Low High Switching Speed Temperature Operating A - Analogue (Programmable Only) 2 Notes: 1. As long as Tj (Junction Temperature) is not exceeded. It is recommended to operate within the normal Operate Supply Voltage of +24Vdc maximum. Operating beyond Absolute Ratings may cause permanent damage to the Hall IC. 2. Preprogrammed by Littelfuse or Customer pending agreement. 3. For custom modifications to the wire length or size, or adding a special connector, please contact Littelfuse. Hall Options Select Option Hall Type Sensitivity Gauss (typ.) Activate - D mm (inch) 2M 2 Wire Switch 120 13.5 (.531) 2H 2 Wire Switch 57 18.5 (.728) 3M 3 Wire Switch 130 12.5 (.492) 3H 3 Wire Switch 59 18.0 (709) AP Analog Programmable Consult Littelfuse D N S Note: Active distances are approximate using NEFEB Magnet 21 x 7 x 4.7 (.827l x .276W x .185H) LITTELFUSE P/N H-58 (c) 2015 Littelfuse Revised: 11/02/15 Specifications are subject to change without notice. littelfuse.com Hall Effect Sensors Flange Mount > 55100 55100 Miniature Flange Mounting Proximity Sensor Termination Specification Cable Length Specification Cable Type: 24 AWG 7/32 PVC 105C UL1430/UL1569 Termination Options Select Option Cable Length mm (inch) Select Option 02 300 (11.81) A Tinned leads (6.40.76)mm F Untinned leads (6.40.76)mm E JST type XHP 2.5mm pitch Part Numbering System Description (Two-wire versions illustrated) 55100 - XX - XX - X Series Hall Option 2M, 2H, 3M, 3H, or AP Cable Length 02 Termination A, E, or F Packaging Packaging Option Packaging Specification Bulk (c) 2015 Littelfuse Revised: 11/02/15 Specifications are subject to change without notice. Bulk Quantity 500 Quantity & Packaging Code N/A Taping Width N/A littelfuse.com