Effective February 2013
Supersedes September 2008
Technical Data TD07002001E
Toggle switch accessories
Table 1. Indicating Plates for 15/32-Inch Bushing-Mounted Switches
Keyway Location
Marking
Material Finish Part NumberOpposite Keyway Keyway Side
Keyway on bottom
OFF
ON
1
32 11
32
5 Dia.
8
15 Dia.
32 1
1
16
ON OFF 0.032 inch steel Plain 30-5632
0.032 inch steel Statuary bronze 30-5632-3
0.032 inch steel Burnished nickel 30-5632-4
0.032 inch brass Black cupric oxide a30-2899-3
RAD PHO 0.032 inch steel Statuary bronze 30-5632-7
0.032 inch steel Burnished nickel 30-5632-6
RUN START 0.032 inch steel Burnished nickel 30-5632-11
HOT COLD 0.032 inch steel Burnished nickel 30-5632-15
HI LOW 0.032 inch steel Burnished nickel 30-5632-16
ON STOP 0.032 inch steel Burnished nickel 30-5632-17
FOR REV 0.032 inch steel Burnished nickel 30-2899-2
AUTO TEST 0.032 inch steel Burnished nickel 30-2899-6
PUSH START 0.032 inch steel Burnished nickel 30-2899-7
RUN TEST 0.032 inch steel Burnished nickel 30-2899-9
BLANK BLANK 0.032 inch steel Plain 30-5632-5
0.032 inch steel Burnished nickel 30-5632-8
0.032 inch brass Brushed 30-5632-9
Keyway on side
ON
OFF
O
F
F
O
N
ON
OFF
I
O
ON OFF 0.032 inch steel Burnished nickel 30-5632-13
OFF ON 0.032 inch steel Burnished nickel 30-2899-8
Keyway on top
ON
OFF
O
F
F
O
N
ON
OFF
I
O
T B 0.032 inch steel Burnished nickel 30-5632-12
OFF ON 0.032 inch steel Burnished nickel 30-5632-14
SET RUN 0.032 inch steel Burnished nickel 30-2899-10
BLANK RESET 0.032 inch steel Burnished nickel 30-2899-12
Keyway on top
ON
OFF
O
F
F
O
N
ON
OFF
I
O
O I 0.032 inch steel Burnished nickel 30-5632-23
I O 0.032 inch steel Burnished nickel 30-5632-19
a White lettering.
2
Technical Data TD07002001E
Effective February 2013
Toggle switch accessories
EATON CORPORATION www.eaton.com
Table 2. Switch Guards a
Switch
Positions Keyway
Location Mounting Catalog
Number
2Opposite hinged end OHM E10TA104
a Red phenolic lever material.
Switch
(Ref.)
Red-Molded
Plastic
Closed
Steel
Open 1.547 (39.29)
Rad.
1.093
(27.76)
Max.
0.032
(0.81)
15/32-32 UN-2A
Thread to Within
0.060 (1.52)
of Shoulder
0.240 (6.10)
Dia.
33°
0.840
(21.34)
0.468
(11.89)
0.688
(17.48)
Rivet
0.688
(17.48)
Max.
0.062
(1.57)
0.031
(0.79)
1.062
(26.97)
0.475
(12.07)
Dia.
1.635 (41.53) Max.
1.830 (46.48) Max.
0.750
(19.05)
Max.
Figure 1. Switch Guard—Approximate Dimensions in Inches (mm)
Table 3. Mounting Hardware for One-Hole Mounting Switches—Dimensions in mm (Inches) ab
Size Description Material Thickness
(Dim. A)
Inside
Diameter
(Dim. B)
O.D. or Dim.
Across Flats
(Dim. C)
Dim. Across
Corners
(Dim. D) Catalog
Number
Mounting Nuts
15/32-32 Hexagon locknut Zinc-chromate treated 1.91 (0.075) —15.88 (0.625) —15-192
Bright nickel–plated brass 1.98 (0.078) —13.87 (0.546) 15.88 (0.625) 15-2525-58
Nickel-plated brass 1.98 (0.078) —13.87 (0.546) 15.88 (0.625) 15-2525-59
Zinc-chromate treated 4.76 (0.188) 19.89 (0.783) 25.80 (1.125) —15-2528-2
Hexagon facenut Nickel-plated brass 1.98 (0.078) —14.27 (0.562) 16.66 (0.656) 15-966-2
Semi-lustre nickel–plated brass 1.98 (0.078) —14.27 (0.562) 16.66 (0.656) 19-966-6
Knurled facenut Bright nickel–plated brass 1.68 (0.066) 14.27 (0.562) 14.27 (0.562) —15-124F1
Black cupric oxide–plated brass 1.68 (0.066) 14.27 (0.562) 14.27 (0.562) —15-124F5
Nickel-plated brass 2.77 (0.109) 15.88 (0.625) 15.88 (0.625) —15-90
Chamfered dress nut Bright nickel–plated brass 3.84 (0.151) 7.92 (0.312) 17.45 (0.687) —15-994-2
Standard knurl nut with shoulder Nickel-plated brass 2.77 (0.109) —15.06 (0.593) —15-2534-14
Dress nut Satin chrome–plated brass 3.18 (0.125) —14.27 (0.562) —15-2523-4
Black nylon 4.75 (0.187) 9.91 (0.390) 16.26 (0.640) —15-1048-3
Knurled dress nut Chrome-plated brass 4.75 (0.187) 7.92 (0.312) 16.26 (0.640) —15-189-5
Mounting Washers and Locking Ring
For 15/32
bushing
Plain washer Cadmium-plated steel 0.79 (0.031) 12.29 (0.484) 19.05 (0.750) —16-1382
Internal tooth lockwasher Trivalent zinc–plated steel 0.53 (0.021) 11.96 (0.471) 15.06 (0.593) —16-3557
Locking ring Zinc-plated steel 1.02 (0.040) 12.07 (0.475) 18.24 (0.718) —29-761-5
a Hardware items are sold for use with Eaton switches only. Minimum ordering quantity on all items is 100. All bushing-mounted switches are furnished with two mounting nuts. One nut is mounted behind the
panel to prevent the bushing sleeve from being distorted if the front panel is overtightened. Eaton accepts no responsibility for damage to switches mounted without the backup nuts.
b Refer to Table 4 for dimensional diagrams.
3
Technical Data TD07002001E
Effective February 2013
Toggle switch accessories
EATON CORPORATION www.eaton.com
Table 4. Dimensions—Approximate in mm (Inches)
Hexagon Locknuts
or Facenuts
Knurled Dress Nut
Catalog Number 15-1048-3
Knurled Facenut Dress Nut
Catalog Number 15-2523-4
Knurled Nut with Shoulder Plain Washer
Chamfered Dress Nut
Catalog Number 15-994-2
Internal Tooth Lockwasher
Knurled Dress Nut
Catalog Number 15-189-5
Locking Ring
Panel seal
• Prevents moisture and contaminants from entering
panel enclosure
• Behind panel mounting
• Stainless steel cup washer ensures proper seating of
silicone rubber seal
• Seal withstands 20 psi water pressure
• Catalog Number 32-341
0.072
0.082
0.427
0.432
0.467
0.472 Dia.
1/16-Inch Lettering (located on angular surface)
Silicone
Rubber
0.670
0.650 Dia. Thickness of
brushing seal is
reduced to 0.080
when mounted to panel.
Cupwasher
Stainless Steel
0.105
0.120
Figure 2. Panel Seal—Dimensions in Inches
Figure 3. Two-Pole Base Connector, Catalog Number 28-3426—
Dimensions in mm (Inches)
Eaton Corporation
Electrical Sector
1111 Superior Avenue
Cleveland, OH 44114 USA
Eaton.com
© 2013 Eaton Corporation
All Rights Reserved
Printed in USA
Publication No. TD07002001E / Z13275
February 2013
Eaton is a registered trademark
of Eaton Corporation.
All other trademarks are property
of their respective owners.
Technical Data TD07002001E
Effective February 2013
Toggle switch accessories
