PFS706EG - Power Integrations

PFS704-729EG

HiperPFS™ Family

www.powerint.com March 2012

High Power PFC Controller with Integrated

High-Voltage MOSFET

Key Beneﬁts

• Single chip solution for boost power factor correction (PFC)

• EN61000-3-2 Class C and D compliant

• High light load efﬁciency at 10% and 20% load

• >95% efﬁciency from 10% load to full load

• <130 mW no-load consumption at 230 VAC with output in

regulation

• <50 mW no-load consumption at 230 VAC in remote off state

• Frequency adjusted over line voltage, and line cycle

• Spread-spectrum across >60 kHz window to simplify EMI

ﬁltering requirements

• Lower boost inductance

• Provides up to 1 kW peak output power

• >1 kW peak power delivery in power limit voltage regulation

mode

• High integration allows smaller form factor, higher power density

designs

• Incorporates control, gate driver, and high-voltage power

MOSFET

• Internal current sense reduces component count and system

losses

• Protection features include: UV, OV, OTP, brown-in/out, cycle-

by-cycle current limit, and power limiting for overload protection

• Halogen free and RoHS compliant

Applications

• PC • High power adaptors

• Printer • High power LED lighting

• LCD TV • Industrial and appliance

• Video game consoles • Generic PFC converters

Figure 1. Typical Application Schematic.

Output Power Table

Product

Maximum Continuous

Output Power Rating at

90 VAC

Peak Output Power

Rating at 90 VAC

PFS704EG 110 W 120 W

PFS706EG 140 W 150 W

PFS708EG 190 W 205 W

PFS710EG 240 W 260 W

PFS712EG 300 W 320 W

PFS714EG 350 W 385 W

PFS716EG 388 W 425 W

Product

Maximum Continuous

Output Power Rating at

180 VAC

Peak Output Power

Rating at 180 VAC

PFS723EG 255 W 280 W

PFS724EG 315 W 350 W

PFS725EG 435 W 480 W

PFS726EG 540 W 600 W

PFS727EG 675 W 750 W

PFS728EG 810 W 900 W

PFS729EG 900 W 1000 W

Table 1. Output Power Table (see Notes on page 9)

PI-6021-110810

VCC

OUT

CONTROL

HiperPFS

Rev. D 03/12

PFS704-729EG

www.powerint.com

Section List

Description .................................................................................................................................................................. 3

Product Highlights ...................................................................................................................................................... 3

Pin Functional Description ......................................................................................................................................... 4

Pin Conﬁguration ...................................................................................................................................................... 4

Functional Block Diagram ........................................................................................................................................ 4

Functional Description ............................................................................................................................................... 5

Output Power Table ................................................................................................................................................. 9

Application Example ............................................................................................................................................10-11

Design, Assembly, and Layout Considerations .................................................................................................... 12

Absolute Maximum Ratings ..................................................................................................................................... 19

Parameter Table ................................................................................................................................................19-25

Typical Performance Characteristics ...................................................................................................................... 26

Package Details ........................................................................................................................................................ 27

Part Ordering Information......................................................................................................................................... 28

Part Marking Information ......................................................................................................................................... 28

Rev. D 03/12

PFS704-729EG

www.powerint.com

Description

The HiperPFS device family members incorporate a continuous

conduction mode (CCM) boost PFC controller, gate driver, and

high voltage power MOSFET in a single, low-proﬁle eSIP™

power package that is able to provide near unity input power

factor. The HiperPFS devices eliminate the PFC converter’s

need for external current sense resistors, the power loss

associated with those components, and leverages an innovative

control technique that adjusts the switching frequency over

output load, input line voltage, and even input line cycle. This

control technique is designed to maximize efﬁciency over the

entire load range of the converter, particularly at light loads.

Additionally, this control technique signiﬁcantly minimizes the

EMI ﬁltering requirements due to its wide-bandwidth spread

spectrum effect. HiperPFS includes Power Integrations’

standard set of comprehensive protection features, such as

integrated soft-start, UV, OV, brown-in/out, and hysteretic thermal

shutdown. HiperPFS also provides cycle-by-cycle current limit

for the power MOSFET, power limiting of the output for over-

load protection, and pin-to-pin short-circuit protection.

HiperPFS’s innovative variable-frequency continuous conduction

mode of operation (VF-CCM) minimizes switching losses by

maintaining a low average switching frequency, while also

varying the switching frequency in order to suppress EMI, the

traditional challenge with continuous-conduction-mode

solutions. Systems using HiperPFS typically reduce the total X

and Y capacitance requirements of the converter, the inductance

of both the boost choke and EMI noise suppression chokes,

reducing overall system size and cost. Additionally, compared

with designs that use discrete MOSFETs and controllers,

HiperPFS devices dramatically reduce component count and

board footprint while simplifying system design and enhancing

reliability. The innovative variable-frequency, continuous

conduction mode controller enables the HiperPFS to realize all

of the beneﬁts of continuous-conduction mode operation while

leveraging low-cost, small, simple EMI ﬁlters.

Many regions mandate high power factor for many electronic

products with high power requirements. These rules are

combined with numerous application-speciﬁc standards that

require high power supply efﬁciency across the entire load

range, from full load to as low as 10% load. High efﬁciency at

light load is a challenge for traditional PFC approaches in which

ﬁxed MOSFET switching frequencies cause ﬁxed switching

losses on each cycle, even at light loads. HiperPFS simpliﬁes

compliance with new and emerging energy-efﬁciency standards

over a broad market space in applications such as PCs, LCD

TVs, notebooks, appliances, pumps, motors, fans, printers, and

LED lighting.

HiperPFS advanced power packaging technology and high

efﬁciency simpliﬁes the complexity of mounting the package

and thermal management, while providing very high power

capabilities in a single compact package; these devices are

suitable for PFC applications from 75 W to 1 kW

Product Highlights

Protected Power Factor Correction Solution

• Incorporates high-voltage power MOSFET, controller, and gate

driver

• EN61000-3-2 Class D compliance

• Integrated protection features reduce external component count

• Accurate built-in brown-in/out protection

• Accurate built-in undervoltage (UV) protection

• Accurate built-in overvoltage (OV) protection

• Hysteretic thermal shutdown (OTP)

• Internal power limiting function for overload protection

• Cycle-by-cycle power switch current limit

• No external current sense required

• Provides “lossless” internal sensing via sense-FET

• Reduces component count and system losses

• Minimizes high current gate drive loop area

• Minimizes output overshoot and stresses during start-up

• Integrated power limit and frequency soft start

• Improve dynamic response

• Input line feed-forward gain adjustment for constant loop

gain across entire input voltage range

• Eliminates up to 40 discrete components for higher reliability

and lower cost

Intelligent Solution for High Efﬁciency and Low EMI

• Continuous conduction mode PFC uses novel constant volt/

amp-second control engine

• High efﬁciency across load using a UF boost diode

• Low cost EMI ﬁlter

• Universal input device (PFS704 – PFS716) utilize frequency

sliding technique for light load efﬁciency improvements

• >95% efﬁciency from 10% load to full load at low line input

voltage

• >96% efﬁciency from 10% load to full load at high line input

voltage

• High line input device (PFS723 – PFS729) maintain higher

average switching frequency to minimize boost inductance

and core size

• >94% efﬁciency from 10% load to full load

• Variable switching frequency to simplify EMI ﬁlter design

• Varies over line input voltage to maximize efﬁciency and

minimize EMI ﬁlter requirements

• Varies with input line cycle voltage by >60 kHz to maximize

spread spectrum effect

Advanced Package for High Power Applications

• Up to 1 kW peak output power capability in a highly compact

package

• Simple clip mounting to heat sink

• Can be directly connected to heat sink with insulation pad

• Provides thermal impedance equivalent to a TO-220

• Staggered pin arrangement for simple routing of board traces

and high voltage creepage requirements

• Single package solution for PFC converter reduces assembly

costs and layout size

Rev. D 03/12

PFS704-729EG

www.powerint.com

Figure 3. Functional Block Diagram.

Pin Functional Description

VOLTAGE MONITOR (V) Pin:

The V pin is tied to the rectiﬁed AC rail through an external

resistor. Internal circuitry detects the peak of the input line

voltage which resembles a full-wave rectiﬁed waveform. The

rectiﬁed high-voltage bus is connected directly to the V pin

voltage through a large resistor (4 MW for PFS70x and PFS71x;

9 MW for PFS72x) to minimize power dissipation and standby

power consumption. A small ceramic capacitor (0.1 mF for

PFS70x and PFS71x; 0.047 mF for PFS72x) is required from the

VOLTAGE MONITOR pin to SIGNAL GROUND pin to bypass

any switching noise present on the rectiﬁed bus. This pin also

features both brown-in and brown-out protection.

FEEDBACK (FB) Pin:

The FEEDBACK pin is high input-impedance reference terminal

that connects to a feedback resistor network. This pin will also

feature fast overvoltage and undervoltage detection circuitry

that will disengage the internal power MOSFET in the event of a

system fault. A 10 nF capacitor is required between the

FEEDBACK to SIGNAL GROUND pins; this capacitor must be

placed very close to the device on the PCB to bypass any

switching noise. This pin is also used for loop compensation.

BIAS POWER (VCC) Pin:

This is a 10-12 VDC bias supply used to power the IC. The bias

voltage must be externally clamped to prevent the VCC pin

from exceeding 13.4 VDC.

SIGNAL GROUND (G) Pin:

Discrete components used in the feedback circuit, including

loop compensation, decoupling capacitors for the supply (VCC)

and line-sense (V) must be referenced to the G pin. The

SIGNAL GROUND pin must not be tied to the SOURCE pin.

SOURCE (S) Pin:

This pin is the source connection of the power switch.

DRAIN (D) Pin:

This is the tab and drain connection of the internal power switch.

Figure 2. Pin Conﬁguration.

PI-5333-113010

“Off-time derived with

constant Volt-Sec

Input Voltage

Emulation

VOFF is a function of the error-voltage (VE) and is used to reduce the average

operating frequency as a function of output power for increased efficiency

(PFS704-716).

(VOFF = 0.8 V for PFS723-729).

The internal derived error-voltage (VE)

regulates the output voltage

MON is the switch current

sense scale factor which

is function of peak line

voltage derived from IVIN

Fast OV

Comparator

FBOV/UV

OTP

VCC

VOLTAGE MONITOR (V)

SIGNAL GROUND (G) SOURCE (S)

BIAS POWER (VCC) DRAIN (D)

FEEDBACK (FB)

FBUV/

FBOFF

VCC+

MON

Internal

Reference

VREF

Transconductance

Error-Amplifier Driver

IOCP

Sense

FET Power

MOSFET

UV Comparator

TIMER

SUPERVISOR

INPUT

LINE INTERFACE

Peak

Detector

INTERNAL

SUPPLY

OTP

SOFT

START

6 V

CINT

MON IS

CINT

VO-VIN

IVPK

Input UV

(IUV-/IUV+)

LEB

OCP

1 kHz

Filter

7 kHz

Filter

Comparator

VOFF

Frequency

Slide

Comparator

Latch

Input UV

FBOV

PI-5334-083110

Exposed Pad

(Backside)

Internally

Connected to

DRAIN Pin

(see eSIP-7G

Package

Drawing)

Exposed Metal

(On Edge)

Internally

Connected to

DRAIN Pin

Exposed Metal (On Edge)

Internally Connected

to GROUND Pin

E Package (eSIP-7G)

1 2 3 4 5 7

VCC

7 5 4 3 2 1

VCC

Rev. D 03/12

PFS704-729EG

www.powerint.com

Functional Description

The HiperPFS is a variable switching frequency boost PFC

solution. More speciﬁcally, it employs a constant amp-second

on-time and constant volt-second off-time control algorithm.

This algorithm is used to regulate the output voltage and shape

the input current to comply with regulatory harmonic current

limits (high power factor). Integrating the switch current and

controlling it to have a constant amp-sec product over the

on-time of the switch allows the average input current to follow

the input voltage. Integrating the difference between the output

and input voltage maintains a constant volt-second balance

dictated by the electro-magnetic properties of the boost inductor

and thus regulates the output voltage and power.

More speciﬁcally, the control technique sets constant volt-

seconds for the off-time (tOFF). The off-time is controlled such

that:

(1)

Since the volt-seconds during the on-time must equal the

volt-seconds during the off-time, to maintain ﬂux equilibrium in

the PFC choke, the on-time (tON) is controlled such that:

(2)

The controller also sets a constant value of charge during each

on-cycle of the power MOSFET. The charge per cycle is varied

gradually over many switching cycles in response to load

changes so it can be regarded as substantially constant for a

half line cycle. With this constant charge (or amp-second)

control, the following relationship is therefore also true:

(3)

Substituting tON from (2) into (3) gives:

(4)

The relationship of (4) demonstrates that by controlling a constant

amp-second on-time and constant volt-second off-time, the input

current IIN is proportional to the input voltage VIN, therefore

providing the fundamental requirement of power factor correction.

This control produces a continuous mode power switch current

waveform that varies both in frequency and peak current value

across a line half-cycle to produce an input current proportional

to the input voltage.

Control Engine

The controller features a low bandwidth error-ampliﬁer which

connects its non-inverting terminal to an internal voltage

reference of 6 V. The inverting terminal of the error-ampliﬁer is

available on the external FEEDBACK pin which connects to the

external feedback resistor divider, transient load speed-up and

compensation networks to regulate the output voltage.

The internal sense-FET switch current is integrated and scaled

by the input voltage peak detector current sense gain (MON) and

compared with the error-ampliﬁer signal (VE) to determine the

cycle on-time. Internally the difference between the input and

output voltage is derived and the resultant is scaled, integrated,

and compared to a voltage reference (VOFF) to determine the

cycle off-time. Careful selection of the internal scaling factors

produce input current waveforms with very low distortion and

high power factor.

The input voltage is internally synthesized using the switch duty

cycle and a 7 kHz low pass ﬁlter. This synthesized input voltage

representation is subtracted from a ﬁxed reference voltage (6 V)

to derive a current source proportional to (VO-VIN). Please refer to

Figure 3.

Line Feed-Forward Scaling Factor (MON)

The VOLTAGE MONITOR (V) pin current is used internally to

derive the peak of the input line voltage which is used to scale

the gain of the current sense signal through the MON variable.

This contribution is required to reduce the dynamic range of the

control feedback signal as well maintain a constant loop gain

over the operating input line range. This line-sense feed-

forward gain adjustment is proportional to the square of the

peak rectiﬁed AC line voltage and is adjusted as a function of V

pin current. The line-sense feed-forward gain is also important

in providing a switch power limit over the input line range.

Besides modifying brown- in/out thresholds, the V pin resistor

also affects power limit of the device

This characteristic is optimized to maintain a relatively constant

internal error-voltage level at full load from an input line of 100

to 230 VAC input (PFS704-716).

Beyond the speciﬁed peak power rating of the device, the

internal power limit feature will regulate the output voltage

below the set regulation threshold as a function of output

overload beyond the peak power rating. Figure 5 illustrates the

typical regulation characteristic as function of load.

Soft-Start with Pin-to-Pin Short-Circuit Protection

Since the FEEDBACK pin is the interface for output voltage

regulation (resistor voltage divider to output voltage) as well as

loop compensation (series RC), the typical application circuit of

the HiperPFS requires an external transistor network to overcome

the inherently slow feedback loop response. Speciﬁcally, an

PI-5335-111610

OFF

(VOUT-VIN)dt

Latch

RESET

Latch

SET

Gate

Drive (Q)

Maximum

ON-time

Minimum

OFF-time

Timing

Supervisor

Figure 4. Idealized Converter Waveforms.

Rev. D 03/12

PFS704-729EG

www.powerint.com

Soft-Start

Check

Sequence

Start

Converter

VCC >

VCC+

Apply 0.5 µA

on FB to

Check Open FB

Apply

6 mA V pin

Current Sink

Is VFB > FBOFF

VFB > FBOFF

and

VFB < FBOV

YES

PI-5337-110910

YES

Is IV > IUV+

Remove

6 mA V pin

Current Sink

Detect Input

Voltage Peak

Slew Power-Limit

Over Soft-Start

Duration

NPN and PNP transistor are tied between the output voltage

divider resistors to limit the maximum overshoot and under-

shoot during a load transient response. To reduce switch and

output diode current stress at start-up, the HiperPFS slews the

internal error-voltage from zero to its steady-state value at

start-up. Figure 6 illustrates the relative relationship between

the application of VCC and power limit soft-start function through

the internal error-voltage.

The error-voltage has a controlled slew rate of 0.25 V/ms at

start-up, corresponding to the tSOFT time duration for a full scale

error voltage of 5 V.

The beginning of soft-start is gated by the VCC+, IUV+ and

FEEDBACK pin voltage thresholds in the sequence described

below. Once the applied VCC is above the VCC+ threshold, the

sensed V pin current is above IUV+ and the feedback pin voltage

is above FBOFF, the IC applies a ~6 mA current sink through the

VOLTAGE MONITOR pin and checks that the FEEDBACK pin

voltage is still above the FBOFF threshold. This checks to ensure

that the FEEDBACK and V pins are not shorted together. In the

event that the FEEDBACK pin voltage is below the FBOFF

PI-5336-110810

Internal Error-Voltage (VE)VCC

Voltage

tSTART-DELAY

tSOFT

VCC+

~5 V

threshold the V pin holds the 6 mA current sink indeﬁnitely until

the FEEDBACK pin is above the FBOFF. If the FEEDBACK pin

voltage is above FBOFF, the IC releases the current source and

resumes with normal soft-start and operation. Figure 7

illustrates this sequence.

Timing Supervisor and Operating Frequency Range

Since the controller is expected to operate with a variable

switching frequency over the line frequency half-cycle, typically

spanning a range of 24 – 95 kHz, the controller also features a

timing supervisor function which monitors and limits the

maximum switch on-time and off-time as well as ensures a

minimum cycle off-time. The timer supervisor limits the normal

operating frequency range for loads in excess of 10% of the

device peak power rating.

Figure 8a shows the typical half-line frequency proﬁle of the

device switching frequency as a function of input voltage at

peak load conditions. Figure 8b shows for a given line condition

the effect of EcoSmart to the switching frequency as a function

of load (PFS704-716). The switching frequency is not a function

of boost choke inductance.

EcoSmart

The PFS704-716 controllers includes an EcoSmart mode

wherein the internal error signal (VE) is used to detect the

converter output power. Since the internal error-signal is

directly proportional to the output power, this signal level is used

to set the average switching frequency as a function of output

power. The off-time integrator control reference (VOFF) is

Figure 7. Start-Up Sequence.

Figure 5. Typical Normalized Output Voltage Characteristics as Function of

Normalized Peak Load Rating

Figure 6. Power Limit Soft-Start Function.

00.2 0.4 0.6 1 1.2 1.40.8

Normalized to Peak Power Rating

Normalized to Set Output Voltage

Regulation Threshold

1.2

0.8

0.6

0.4

0.2

PI-6216-113010

Rev. D 03/12

PFS704-729EG

www.powerint.com

PI-5338-021711

OFF

~5 V

(full power)

~4.8 V

PFS704-716

VIN < 140 VAC

PFS704-716

VIN > 170 VAC

PFS723-729

~5 V

~2.5 V

~1.25 V

~0.8 V

OFF

at V

= 0 V

~170 VAC ~140 VAC

~5 V

~2.5 V

controlled with respect to the internal error-voltage level (output

power) to allow the converter to maintain output voltage

regulation and relatively ﬂat conversion efﬁciency between 10%

to 100% of rated load which is essential to meet many efﬁciency

directives.

The degree of frequency slide is also controlled as a function of

peak input line voltage, at high input line the maximum off-time

voltage reference at zero error-voltage will be approximately 1/2

of the maximum value at low input line conditions.

The lower VOFF slope reduces the average frequency swing for

high input line operation.

Protection Modes

VOLTAGE MONITOR (V) Pin Shutdown

The VOLTAGE MONITOR pin features a shutdown protection

mode which can be used with the VOLTAGE MONITOR pin

resistor or external circuitry to cover system faults. During

start-up (1 V < VFB < 5.8 V) in the event the current through the

VOLTAGE MONITOR pin exceeds the IV(OFF) threshold for a

duration exceeding approximately (1 ms), the IC disables the

internal MOSFET for the entire duration that the V pin current is

above IV(OFF). In normal operation, if the current through the V

pin exceeds the IV(OFF) threshold for a duration exceeding tV(OFF),

the IC will reinitiate the start-up sequence.

Brown-In Protection (IUV+)

The VOLTAGE MONITOR pin features an input line undervoltage

detection to limit the minimum start-up voltage detected

through the V pin. This detection threshold will inhibit the

device from starting at very low input AC voltage.

Brown-Out Protection (IUV-)

The V pin features a brown-out protection mode wherein the

HiperPFS will turn-off when the V pin current is below the Line

UV-threshold for a period exceeding the tREFRESH time period. In

the event a single half-line cycle is missing (normal operating

line frequency is 47 to 63 Hz) the brown-out protection will not

be activated. The HiperPFS shutdown in effect gradually

reduces the internal error-voltage to zero volts at rate of 1 V/ms

Figure 8. (a) Frequency Variation Over Line Half-Cycle as a Function of Input Voltage (b) Frequency Variation Over Line Half-Cycle as a Function of Load.

Figure 9. VOFF vs. VE and VOFF vs. Input Voltage.

045 90 135 180

PI-6217-110110

120

230 VAC 180 VAC 135 VAC 115 VAC

Peak Load

90 VAC

110

100

Frequency (kHz)

Line Conduction Angle (°C)

045 90 135 180

PI-6218-102910

120

110

100

Frequency (kHz)

Line Conduction Angle (°C)

100% Peak Load

75% Peak Load

VIN = 115 VAC

25% Peak Load

50% Peak Load

Expected Frequency

Range at Peak

Rated Load

Rev. D 03/12

PFS704-729EG

www.powerint.com

PI-5470-110810

IOCP

~170 VAC

PFS704-716

VIN

~140 VAC

IV < 48 µA

IV > 59 µA

Figure 10. Line Dependant OCP.

to decay the power MOSFET on-time to zero. At peak power

(VE ~5 V) the shutdown time will be approximately 5 ms. The

internal error-voltage is held at 0 V for as long as the input peak

voltage is below the brown-in (IUV+) threshold. The internal

error-voltage controlled slew to 0 V gradually reduces the switch

on-time to zero to deplete energy stored in the boost choke as

well as input EMI ﬁlter for power-down. Once the error-voltage

reaches zero volts the controller is effectively in an off-state

(gated by 5 ms timer) and will restart once all the conditions of

soft-start are satisﬁed.

The brown-out threshold is reduced to IUV-SS during start-up until

the FEEDBACK pin exceeds approximately 5.8 V. Temporarily

reducing the brown-out threshold prevents false turn-off at high

power start-up when the voltage drop across the input bridge

rectiﬁer and ﬁlter stage may cause the rectiﬁed input to sag

below the brown-out threshold.

Fast Output Voltage Overvoltage Protection (FBOV)

The FEEDBACK pin features a means to detect an output

overvoltage condition through the FEEDBACK pin and disables

the power MOSFET until the sensed output voltage falls below

the FBOV threshold. A deglitch ﬁlter (~2 ms) is used to prevent

the controller from falsely triggering this mode. An FBOV event in

excess of the 2 ms delay will terminate the switch cycle immediately.

This detection circuit also includes some hysteresis.

Output Voltage Undervoltage Protection (FBUV)

The FEEDBACK pin features an undervoltage detection to

detect an output overload or a broken feedback loop. If the IC

detects the falling edge on the FEEDBACK pin that has fallen

below FBUV threshold, it will turn-off the internal power MOSFET

and reinitiate the start-up sequence. Similar to the FBOV

detection, this mode has a deglitch ﬁlter of approximately 100 ms.

VCC Undervoltage Protection (UVLO)

The BIAS POWER (VCC) pin has an undervoltage lock-out

protection which inhibits the IC from starting unless the applied

VCC voltage is above the VCC+ threshold. The IC initiates a

soft-start once the VCC pin voltage exceeds the VCC+ threshold.

After start-up the IC will continue to operate until the VCC pin

voltage has fallen below VCC- level. The absolute maximum

voltage of the VCC pin is 13.4 V which must be externally limited

to prevent damage to the IC.

Over-Current Protection

The device includes a cycle-by-cycle over-current-protection

(OCP) mode which protects the device in the event of a

catastrophic fault. The OCP mode in the PFS704-716 is input

line dependent as shown in Figure 10. The intention of OCP in

this device is strictly protection of the internal power MOSFET

and is not intended to protect the converter from output

short-circuit or overload fault conditions.

The PFS704-716 controller latches the high line OCP for a 1/2

line cycle and updates the OCP status after the expiration of a

5 ms block-out timer. This feature has particular beneﬁt for

hard-start after an AC line cycle drop where the peak detector

may falsely detect a low input line condition even though the

input is at high input line.

The leading edge blanking circuit inhibits the current limit

comparator for a short time (tLEB) after the power MOSFET is

turned on. This leading edge blanking time must be set so that

current spikes caused by capacitance and rectiﬁer reverse

recovery time will not cause premature termination of the

MOSFET conduction.

Safe Operating Range (SOA) Mode

Since the cycle-by-cycle OCP mechanism described above

does not prevent the possibility of inductor current “stair-

casing”, an SOA mode is required. Rapid build up of the device

current can occur in event of inductor saturation or when the

input and output voltages are equal (non or very short

inductor reset time).

The SOA mode is triggered whenever the device reaches

current limit (IOCP) and the on-time is less than tSOA.

The SOA mode forces an off-time equal to tOCP and pulls the

internal error-voltage (VE) down to approximately 1/2 of its set

value.

Open FEEDBACK Pin Protection

The FEEDBACK pin also features a static current of IFB that is

continuously sourced out of the pin to protect against a fault

related to an open FEEDBACK pin. The internal current source

introduces a static offset to the output regulation which must be

accounted for in selecting the output feedback regulation

components.

Hysteretic Thermal Shutdown

The thermal shutdown circuitry senses the controller die

temperature. The threshold is set at 118 °C typical with a 50 °C

hysteresis. When the die temperature rises above this threshold

(118 °C +8/-7 °C), the power MOSFET switching is disabled and

remains disabled until the die temperature falls by ~50 °C, at

which point the device will reinitiate a soft-start and start-up

sequence.

Rev. D 03/12

PFS704-729EG

www.powerint.com

Output Power Table1

Product

Maximum Continuous

Output Power Rating at

90 VAC2

Peak Output Power

Rating at 90 VAC5Product

Maximum Continuous

Output Power Rating at

180 VAC4

Peak Output Power

Rating at 180 VAC5

Minimum3Maximum

PFS704EG 85 W 110 W 120 W PFS723EG 255 W 280 W

PFS706EG 105 W 140 W 150 W PFS724EG 315 W 350 W

PFS708EG 140 W 190 W 205 W PFS725EG 435 W 480 W

PFS710EG 180 W 240 W 260 W PFS726EG 540 W 600 W

PFS712EG 225 W 300 W 320 W PFS727EG 675 W 750 W

PFS714EG 265 W 350 W 385 W PFS728EG 810 W 900 W

PFS716EG 295 W 388 W 425 W PFS729EG 900 W 1000 W

Table 2. Output Power Table.

Notes:

1. See Key Application considerations.

2. Maximum practical continuous power at 90 VAC in an open-frame design with adequate heat sinking, measured at 50 °C ambient.

3. Recommended lower range of maximum continuous power for best light load efﬁciency; HiperPFS will operate and perform below this level.

4. Maximum practical continuous power at 180 VAC in an open-frame design with adequate heat sinking, measured at 50 °C ambient.

5. Internal output power limit.

Rev. D 03/12

PFS704-729EG

www.powerint.com

Application Example

A High Efﬁciency, 347 W, 380 VDC Universal Input PFC

The circuit shown in Figure 11 is designed using a PFS714EG

device from the HiperPFS family of integrated PFC controllers.

This design is rated for a continuous output power of 347 W

and provides a regulated output voltage of 380 VDC nominal

maintaining a high input power factor and overall efﬁciency from

light load to full load.

Fuse F1 provides protection to the circuit and isolates it from the

AC supply in case of a fault. Diode bridge BR1 rectiﬁes the AC

input. Capacitors C3, C4, C5, C6 and C19 together with

inductors L1, L2, L3 and L4 form the EMI ﬁlter reducing the

common mode and differential mode noise. Resistors R1, R3

and CAPZero, IC U2 are required to discharge the EMI ﬁlter

capacitors once the circuit is disconnected. CAPZero

eliminates static losses in R1 and R2 by only connecting these

components across the input when AC is removed.

The boost converter stage consists of inductor L5, diode rectiﬁer

D2 and the HiperPFS IC U1. This converter stage works as a

boost converter and controls the input current of the power

supply while simultaneously regulating the output DC voltage.

Diode D1 prevents a resonant build up of output voltage at start-

up by bypassing inductor L5 while simultaneously charging

output capacitor C15. Thermistor RT1 limits the inrush input

current of the circuit at start-up and prevents saturation of L5.

In most high-performance designs, a relay will be used to

bypass the thermistor after start-up to improve power supply

efﬁciency. Therefore efﬁciency measurement, that represents

the high performance conﬁguration, the thermistors should be

shorted. Capacitors C14 and C21 are used for reducing the

loop length and area of the output circuit to reduce EMI and

overshoot of voltage across the drain and source of the

MOSFET inside U1 at each switching instant.

The PFS714EG IC requires a regulated supply of 12 V for

operation and must not exceed 13.4 V. Resistors R6, R16, R17,

Zener diode VR1, and transistor Q3 form a shunt regulator that

prevents the supply voltage to IC U1 from exceeding 12 V.

Capacitors C8, C18 and C20 ﬁlter the supply voltage and

provide decoupling to ensure reliable operation of IC U1. Diode

D5 prevents destruction of U1 if the auxiliary input is inadvertently

connected reverse polarity.

The rectiﬁed AC input voltage of the power supply is sensed by

IC U1 using resistors R4, R5 and R19. The capacitor C12 ﬁlters

any noise on this signal.

Divider network comprising of resistors R9, R10, R11, R12, R13,

and R14 are used to scale the output voltage and provide

feedback to IC U1. The circuit comprising of diode D4,

transistor Q1, Q2 and the resistors R12 and R13 form a non-

linear feedback circuit which improves the load transient

response by improving the response time of the PFC circuit.

Resistor R7, R8, R15, and capacitors C13 and C17 are required

for shaping the loop response of the feedback network. The

combination of resistor R8 and capacitor C13 provide a low

frequency zero and the resistor R15 and capacitor C13 form a

low frequency pole.

PI-6197-111110

220 kΩ

RT1

10 Ω

100 Ω

47 µF

50 V

DL4001

VR1

BZX84C12LT1G

MMBT4401LT1G

R16

100 Ω

R17

3.01 kΩ

220 kΩ

R18

10 Ω

2 W

Ferrite Bead

1.5 MΩ

R19

1.5 MΩ

1 MΩ

1.38 mH

BR1

GBU806

600 V

1N5408

1N4148

BAV116

130 V

STTH8S06D

14 mH

100 nF

275 VAC

C19

1 µF

310 V

680 pF

250 VAC

1 µF

400 V

R13

2.21 kΩ

2 kΩ

R12

2.21 kΩ

R10

1.6 MΩ

R11

732 kΩ

1.5 MΩ

R15

160 kΩ

C17

470 pF

100 V

C21

10 nF

1 kV

C14

10 nF

1 kV

680 pF

250 VAC

680 nF

275 VAC

6.3 A

RV1

320 VAC

VCCV

OUT

380 VDC

Auxiliary

Power

Supply

CONTROL

HiperPFS

PFS714EG

C11

10 nF

50 V

C12

100 nF

50 V C18

1 µF

25 V

C13

4.7 µF

25 V

C20

100 nF

50 V

MMBT4401

CAPZero

CAP006DG

100 µH

C16

100 nF

200 V

R14

57.6 kΩ

MMBT4403

100

C15

270 µF

450 V

*Optional Component

3.01 kΩ

Figure 11. 347 W PFC using PFS714EG.

Rev. D 03/12

PFS704-729EG

www.powerint.com

Figure 12. 180 W PFC using PFS708EG.

Figure 13. 900 W PFC using PFS729EG.

PI-6229-110210

750 kΩ

RT1

10 Ω

750 kΩ

1.5 MΩ

R19

1.5 MΩ

1 MΩ

1.7 mH

BR1

3KBP06M

600 V

1N5408

1N4148

BAV116

130 V

STTH3R06U

10 mH C19

220 nF

275 VAC

100 pF

250 VAC

470 nF

400 V

R13

2.21 kΩ

2 kΩ

R12

2.21 kΩ

R10

1.6 MΩ

R11

732 kΩ

1.5 MΩ

R15

160 kΩ

C17

470 pF

100 V

C14

10 nF

1 kV

100 pF

250 VAC

220 nF

275 VAC

3.15 A

RV1

320 VAC

VCCV

OUT

12 V

Auxiliary

Power

Supply

CONTROL

HiperPFS

PFS708EG

C11

10 nF

50 V

C12

100 nF

50 V C18

1 µF

25 V

C13

4.7 µF

25 V

C20

47 µF

25 V

MMBT4401

CAPZero

CAP002DG

100 µH

C16

100 nF

200 V

R14

57.6 kΩ

MMBT4403

C15

150 µF

450 V

3.01 kΩ

PI-6230-111110

220 kΩ

RT1

10 Ω

220 kΩ

R18

10 Ω

2 W

3 MΩ

R19

3 MΩ

2.04 mH

BR1

GBU10J

600 V

1N5408

1N4148

BAV116

130 V

STTH12R06

14 mH C19

1 µF

275 VAC

680 pF

250 VAC

1.5 µF

400 V

R13

2.21 kΩ

2 kΩ

R12

2.21 kΩ

R10

1.6 MΩ

R11

732 kΩ

1.5 MΩ

R15

160 kΩ

C17

470 pF

100 V

C21

10 nF

1 kV

C14

10 nF

1 kV

680 pF

250 VAC

680 nF

275 VAC

8 A

RV1

320 VAC

VCCV

OUT

Ferrite Bead

100 µH

CONTROL

HiperPFS

PFS729EG

C11

10 nF

50 V

C12

47 nF

50 V C18

1 µF

25 V

100 nF

275 VAC

C13

4.7 µF

25 V

C20

100 nF

25 V

MMBT4401

CAPZero

CAP006DG

100 µH

C16

100 nF

200 V

R14

57.6 kΩ

MMBT4403

C15

820 µF

450 V

3.01 kΩ

100 Ω

47 µF

50 V

DL4001

VR1

BZX84C12LT1G

MMBT4401LT1G

R16

100 Ω

R17

3.01 kΩ

15 V

Auxiliary

Power

Supply

Rev. D 03/12

PFS704-729EG

www.powerint.com

Design, Assembly, and Layout Considerations

Power Table

The data sheet power table as shown in Table 2 represents the

maximum practical continuous output power based on the

following conditions:

For the universal input devices (PFS704-716):

1. An input voltage range of 90 VAC to 264 VAC

2. Overall efﬁciency of at least 93% at the lowest operating

voltage

3. Use of ultrafast recovery diode or high performance diode for

PFC output.

4. Sufﬁcient heat sinking to keep device temperature ≤100 ºC

5. 380 V to 385 V nominal output

For the 230 V only devices (PFS723-729):

1. An input voltage range of 180 VAC to 264 VAC

2. Overall efﬁciency of at least 96% at the lowest operating

voltage

3. Use of ultrafast recovery diode or high performance diode

for PFC output.

4. Sufﬁcient heat sinking to keep device temperature ≤100 ºC

5. 380 V to 385 V nominal output

Operation beyond the limits stated above will require derating.

Use of a nominal output voltage higher than 390 V is not

recommended for HiperPFS based designs. Operation at

voltages higher than 390 V can result in higher than expected

drain-source voltage during line and load transients.

HiperPFS Selection

Selection of the optimum HiperPFS part depends on required

maximum output power, PFC efﬁciency and overall system

efﬁciency (when used with a second stage DC-DC converter),

heat sinking constraints, system requirements and cost goals.

The HiperPFS part used in a design can be easily replaced with

the next higher or lower part in the power table to optimize

performance, improve efﬁciency or for applications where there

are thermal design constraints. Minor adjustments to the

inductance value and EMI ﬁlter components may be necessary

in some designs when the next higher or the next lower

HiperPFS part is used in an existing design for performance

optimization.

Every HiperPFS family part has an optimal load level where it

offers the most value. Operating frequency of a part will change

depending on load level. Change of frequency will result in

change in peak to peak current ripple in the inductance used.

Change in current ripple will affect input PF and total harmonic

distortion of input current.

Input Fuse and Protection Circuit

The input fuse should be rated for a continuous current above

the input current at which the PFC turns-off due to input under

voltage. This voltage is referred to as the brown-out voltage.

The fuse should also have sufﬁcient I2t rating in order to avoid

nuisance failures during start-up. At start a large current is

drawn from the input as the output capacitor charges to the

peak of the applied voltage. The charging current is only limited

by any inrush limiting thermistors, impedance of the EMI ﬁlter

inductors and the forward resistance of the input rectiﬁer

diodes.

A MOV will typically be required to protect the PFC from line

surges. Selection of the MOV rating will depend on the energy

level (EN1000-4-5 Class level) to which the PFC is required to

withstand.

Input EMI Filter

The variable switching frequency of the HiperPFS effectively

modulates the switching frequency and reduces conducted EMI

peaks associated with the harmonics of the fundamental

switching frequency. This is particularly beneﬁcial for the

average detection mode used in EMI measurements.

The PFC is a switching converter and will need an EMI ﬁlter at

the input in order to meet the requirements of most safety

agency standards for conducted and radiated EMI. Typically a

common mode ﬁlter with X capacitors connected across the

line will provide the required attenuation of high frequency

components of input current to an acceptable level. The

leakage reactance of the common mode ﬁlter inductor and the

X capacitors form a low pass ﬁlter. In some designs, additional

differential ﬁlter inductors may have to be used to supplement

the differential inductance of the common mode choke.

A ﬁlter capacitor with low ESR and high ripple current capability

should be connected at the output of the input bridge rectiﬁer.

This capacitor reduces the generation of the switching frequency

components of the input current ripple and simpliﬁes EMI ﬁlter

design. Typically, 0.33 mF per 100 W should be used for

universal input designs and 0.15 mF per 100 W of output power

should be used for 230 VAC only designs.

It is often possible to use a higher value of capacitance after the

bridge rectiﬁer and reduce the X capacitance in the EMI ﬁlter.

Regulatory requirements require use of a discharge resistor to

be connected across the input (X) capacitance on the AC side

of the bridge rectiﬁer. This is to ensure that residual charge is

dissipated after the input voltage is removed when the

capacitance is higher than 0.1 mF. Use of CAPZero integrated

circuits from Power Integrations, helps eliminate the steady

state losses associated with the use of discharge resistors

connected permanently across the X capacitors.

Inductor Design

It is recommended that the inductor be designed with the

maximum operating ﬂux density less than 0.3 T and a peak ﬂux

density less than 0.42 T at maximum current limit when a ferrite

core is used. If a core made from Sendust or MPP is used, the

ﬂux density should not exceed 1 T. A powder core inductor will

have a signiﬁcant drop in inductance when the ﬂux density

approaches 1 T.

For high-line only designs, the value of KP (the ratio of peak to

ripple current) of the drain current at the peak of the input

voltage waveform should be kept below 0.5 for ferrite core and

Rev. D 03/12

PFS704-729EG

www.powerint.com

0.675 for powder core designs respectively. For universal input

designs, KP should be kept below 0.25 for ferrite core and 0.675

for powder core respectively. For high performance designs,

use of Litz wire is recommended to reduce copper loss due to

skin effect and proximity effect. For toroidal inductors the

numbers of layers should be less than 3 and for bobbin wound

inductors, inter layer insulation should be used to minimize inter

layer capacitance.

Output Diode

For a 385 V nominal PFC output voltage, use of a diode with

600 V or higher PIV rating is recommended. CCM operation

with hard switching demands that diodes with low reverse

recovery time and reverse recovery charge should be used. The

variable frequency CCM operation of HiperPFS reduces diode

switching losses as compared to ﬁxed frequency solutions and

enables use of easily available high frequency diodes such as

the Turbo-2 series from STMicroelectronics. Diodes with soft

recovery characteristics that result in a reduced EMI are available

from a number of manufacturers. For highly demanding

applications such as 80 PLUS Gold power supplies, use of

Silicon Carbide diodes may be considered. These uses will

typically provide further full load improvement in efﬁciency.

The diodes will be required to have a forward continuous current

rating of at least 1.2 A to 1.5 A for every 100 W of output power.

Output Capacitor

For a 385 V nominal PFC, use of a electrolytic capacitor with

450 V or higher continuous rating is recommended. The

capacitance required is dependent on the acceptable level of

output ripple and any hold up time requirements. The equations

below provide an easy way to determine the required capacitance

in order to meet the hold up time requirement and also to meet

the output ripple requirements. The higher of the two values

would be required to be used:

Capacitance required for meeting the hold up requirement is

calculated using the equation:

CVV

Pt2

()

OUTOUT MIN

OUTHOLDUP

CO PFC output capacitance in F.

PO PFC output power in watts.

tHOLD-UP Hold-up time speciﬁcation for the power supply

in seconds.

VOUT Lowest nominal output voltage of the PFC in volts.

VOUT(MIN) Lowest permissible output voltage of the PFC at

the end of hold-up time in volts.

Capacitance required for meeting the low frequency ripple

speciﬁcation is calculated using the equation:

CfV

()

LOPFC

OMAX

####

fL Input frequency in Hz

ΔVO Peak-peak output voltage ripple in volts

ηPFC PFC operating efﬁciency

IO(MAX) Maximum output current in amps

Capacitance calculated using the above method should be

appropriately increased to account for ageing and tolerances.

Power Supply for the IC

A 12 V regulated supply should be used for the HiperPFS. If the

VCC exceeds 13.4 V, the HiperPFS may be damaged. In most

applications a simple series pass linear regulator made using an

NPN transistor and Zener diode is adequate since the HiperPFS

only requires approximately 3.4 mA maximum for its operation.

It is recommended that a 1 mF or higher, low ESR ceramic

capacitor be used to decouple the VCC supply. This capacitor

should be placed directly at the IC on the circuit board.

Line-Sense Network

The line-sense network connected to the V pin provides input

voltage information to the HiperPFS. The value of this resistance

sets the brown-in and brown-out threshold for the part. A value

of 4 MW is recommended for use with the universal input parts

and a value of 9 MW is recommended for the 230 VAC only

parts. Only 1% tolerance resistors are recommended. This

resistance value may be modiﬁed to adjust the brown-in

threshold if required however change of this value will affect the

maximum power delivered by the part.

A decoupling capacitor of 0.1 mF is required to be connected

from the VOLTAGE MONITOR pin to the GROUND pin of the

HiperPFS for the universal input parts and a decoupling

capacitor of 0.047 mF is required for the 230 VAC only parts.

This capacitor should be placed directly at the part on the

circuit board.

Feedback Network

A resistor divider network that provides 6 V at the feedback pin

at the rated output voltage should be used. The compensation

elements are included with the feedback divider network since

the HiperPFS does not have a separate pin for compensation.

The HiperPFS based PFC has two loops in its feedback. It has

an inner current loop and a low bandwidth outer voltage loop

which ensures high input power factor. The compensation RC

circuit included with the feedback network reduces the response

time of the HiperPFS to fast changes in output voltage resulting

from transient loads. The feedback circuit recommended for

use with the HiperPFS includes a pair of transistors that are

biased in a way that the transistors are in cutoff during normal

operation. When a rapid change occurs in the output voltage,

these transistors conduct momentarily to correct the feedback

pin voltage rapidly thereby helping the HiperPFS to respond to

the changes in output voltage without the delay associated with

a low bandwidth feedback loop.

The recommended circuit and the associated component

values are shown in Figure 14.

Resistors, R1 to R5 comprise of the main output voltage divider

network. The sum of resistors R1, R2 and R3 is the upper

divider resistor and the lower feedback resistor is comprised of

the sum of resistors R4 and R5. Capacitor C1 is a soft-ﬁnish

capacitor that reduces output voltage overshoot at start-up.

Resistor R8 and capacitor C3 form a low pass ﬁlter to ﬁlter any

switching noise from coupling into the FEEDBACK pin. Resistor

Rev. D 03/12

PFS704-729EG

www.powerint.com

PI-6228-111110

VCCV

CONTROL

HiperPFS

C3 C2

B+

VCC

R7 and capacitor C2 is the loop compensation network which

introduces a low frequency zero required to tailor the loop

response to ensure low cross-over frequency and sufﬁcient

phase margin. Resistor R6 isolates the fast portion (resistor

voltage divider network comprising of resistors R1 to R5) and

the slow feedback loop compensator circuit (resistor R7 and

capacitor C2). Transistors Q1 and Q2, biased with resistors R3

and R4 respectively, detect output voltage transient conditions

and provide the FEEDBACK pin with “fast” information to

increase the loop response of the system. Diode D1 is included

to cover a single point fault condition wherein capacitor C2 is

shorted. In the event C2 is short-circuited, the FEEDBACK pin

is forced below the FBOFF threshold through diode D1 and

subsequently turns the HiperPFS off. Only a standard recovery

diode should be used for D1. Use of ultrafast or fast recovery

diode is not recommended including small signal diodes (e.g.

1N4148) which are typically also fast recovery.

The recommended values for the components used are as

follows:

R5 = 57.6 kW

R3, R4 = 2.2 kW

R2 = 732 kW

C1 = 0.1 mF, 100 V X7R/NPO

R6 = 160 kW

R7 = 3 kW

R8 = 2 kW

C2 = 4.7 mF

C3 = 10 nF (For layouts that result in excessive noise on the

feedback signal, a 20 nF capacitor may be used).

D1 = BAV116 W or 1N4007 (A general purpose standard

recovery diode should only be used).

Q1, Q2 = Small signal transistors equivalent to 2N4401 and

2N4403.

Figure 14. Recommended Feedback Circuit.

When the above component values are used, the value of

resistor R1 can be calculated using the equation below:

10010

Since the total voltage across resistor R1 is approximately

301 V, resistor R1 may have to be divided into two or more

resistors to distribute the voltage stress below the voltage

ratings of the resistor used.

The value of resistor R7 will have to be adjusted in some

designs and as a guideline the value from the following

calculation can be used:

RR VC

X==

PO Maximum continuous output power in watts

VO Nominal PFC output voltage in volts

CO PFC output capacitance in farads

Improvement in low frequency phase margin can be achieved by

increasing the value of the capacitor C2 however increase in value

of capacitor C2 will result in some increase in overshoot at the

output of the PFC during transient loading and should be veriﬁed.

Diode D2 connected in series with the collector of the NPN

transistor Q1 is to prevent loading of the feedback circuit when

the VCC is absent. Presence of this diode ensures that there is

no start-up delay when the VCC is applied to the HiperPFS, the

feedback circuit, and transistor.

Heat Sinking and Thermal Design

The exposed pad on the HiperPFS eSIP package is internally

connected to the drain of the MOSFET. Due to the signiﬁcant

amount of power dissipated in the part, the HiperPFS should be

mounted on a rectangular heat spreader made of thermally

conductive material such as Aluminum or Copper. Figure 15

shows an example of the recommended assembly for the

HiperPFS. In this assembly shown, a 0.76 mm thick aluminum

heat spreader is used. A thermally conductive sil pad should be

used to separate the heat spreader from the heat sink. A thin

ﬁlm of thermally conductive silicone grease should be applied to

the rear surface of the HiperPFS to ensure low thermal

resistance contact between the package of the HiperPFS and

the heat spreader.

For universal input applications up to 150 W and 230 VAC only

applications up to 300 W, the heat spreader is not essential.

Use of heat spreader in these applications will help reduce

temperature of the part and heat spreaders can be used if

necessary. Figure 17 shows an example of the recommended

assembly for lower power designs that do not need a heat

spreader.

The HiperPFS is electrically connected to the heat spreader and

the heat sink is required to be connected to the source in order

to reduce EMI. The voltage between the heat spreader and

heat sink can easily exceed 400 V during transient conditions.

Attention should be placed on creepage and clearance based

on applicable safety speciﬁcation.

Rev. D 03/12

PFS704-729EG

www.powerint.com

Figure 15. Heat Sink Assembly Example – High Power Designs.

Figure 16. Heat Sink Assembly – High Power Designs.

1. SCREW

2. SHOULDER WASHER

3. EDGE CLIP

4. HiperPFS

5. THERMALLY CONDUCTIVE

SILICONE GREASE

6. FIBER WASHER

7. CUSTOM ALUMINUM

HEATSPREADER

8. KAPTON SILPAD INSULATOR

TO-247

9. HEAT SINK

10. FLAT WASHER

11. LOCK WASHER

12. NUT

Rev. D 03/12

PFS704-729EG

www.powerint.com

Figure 17. Heat Sink Assembly Example – Low Power Designs.

Figure 18. Heat Sink Assembly – Low Power Designs.

1. SCREW

2. EDGE CLIP

3. HiperPFS

4. KAPTON SILPAD

INSU L ATO R

5. HEAT SINK

6. FLAT WASHER

7. LOCK WASHER

8. NUT

Rev. D 03/12

PFS704-729EG

www.powerint.com

PCB Design Guidelines and Design Example

The line-sense network and the feedback circuit use large

resistance values in order to minimize power dissipation in the

feedback network and the line-sense network. Care should be

taken to place the feedback circuit and the line-sense network

components away from the high voltage and high current nodes

to minimize any interference. Any noise injected in the feedback

network or the line-sense network will typically manifest as

degradation of power factor. Excessive noise injection can lead

to waveform instability or dissymmetry.

The EMI ﬁlter components should be clustered together to

improve ﬁlter effectiveness. The placement of the EMI ﬁlter

components on the circuit board should be such that the input

circuit is located away from the drain node of the HiperPFS, the

output diode of the PFC or the PFC inductor.

A ﬁlter or decoupling capacitor should be placed at the output

of the bridge rectiﬁer. This capacitor together with the

X capacitance in the EMI ﬁlter and the differential inductance of

the EMI ﬁlter section and the source impedance, works as a

ﬁlter to reduce the switching frequency current ripple in the

input current. This capacitor also helps to minimize the loop

Figure 19. PCB Layout Example for System Power Supply consisting of a PFC and a Second Stage Converter.

area of the switching frequency current loop thereby reducing

EMI.

The connection between the HiperPFS drain node, output

diode drain terminal and the PFC inductor should be kept as

small as possible.

A low loss ceramic dielectric capacitor should be connected

between the cathode of the PFC output diode and the source

terminal of the HiperPFS. This ensures that the loop area of the

loop carrying high frequency currents at the transition of

switch-off of the MOSFET small and helps to reduce radiated

EMI due to high frequency pulsating nature of the diode current

traversing through the loop.

During placement of components on the board, it is best to

place the VOLTAGE MONITOR pin, FEEDBACK pin and VCC

pin decoupling capacitors close to the HiperPFS before the

other components are placed and routed. Power supply return

trace from the GROUND pin should be separate from the trace

connecting the feedback circuit components to the GROUND pin.

PFC

Output

EMI Filter

Thermistor

Shorting Relay

Bridge

Rectifier

PFC

Inductor

HiperPFS

Auxiliary Supply for PFC –

from Standby Power Supply

Second Stage

Converter

Input

Capacitor

(CIN)

PFC Output

Capacitor

PI-6238-012611

AC Input

Rev. D 03/12

PFS704-729EG

www.powerint.com

To minimize effect of trace impedance affecting regulation,

output feedback should be taken directly from the output

capacitor positive terminal. The upper end of the line-sense

resistors should be connected to the high frequency ﬁlter

capacitor connected at the output of the bridge rectiﬁer.

Quick Design Checklist

As with any power supply design, all HiperPFS designs should

be veriﬁed on the bench to make sure that component

speciﬁcations are not exceeded under worst-case conditions.

The following minimum set of tests is strongly recommended:

1. Maximum drain voltage – verify that peak VDS does not

exceed 530 V at lowest input voltage and maximum overload

output power. Maximum overload output power occurs

when the output is overloaded to a level just above the

highest rated load or before the power supply output voltage

starts falling out of regulation. Additional external snubbers

should be used if this voltage is exceeded. In most designs,

addition of a ceramic capacitor in the range of 33 pF and

100 pF connected across the PFC output diode will reduce

the maximum drain-source voltage to a level below the BVDSS

rating. When measuring drain-source voltage of the MOSFET,

a high voltage probe should be used. When the probe tip is

removed, a silver ring in the vicinity of the probe tip can be

seen. This ring is at ground potential and the best ground

connection point for making noise free measurements.

Wrapping stiff wire around the ground ring and then

connecting that ground wire into the circuit with the shortest

possible wire length, and connecting the probe tip to the

point being measured, ensures error free measurement.

2. Maximum drain current – at maximum ambient temperature,

minimum input voltage and maximum output load, verify

drain current waveforms at start-up for any signs of inductor

saturation and excessive leading edge current spikes.

HiperPFS has a leading edge blanking time of 220 ns to

prevent premature termination of the ON-cycle. Verify that

the leading edge current spike is below the allowed current

limit for the drain current waveform at the end of the 220 ns

blanking period. If a wire loop is inserted in series with the

drain, it forms a small stray inductance in series with the

drain. This stray inductance will add to the leading edge

voltage spike on the drain source waveform. The drain-

source voltage waveform should therefore never be measured

with this loop. An alternate measurement that can provide

drain current level and information regarding slope of the

inductor current can be obtained by monitoring the inductor

current instead. A wire loop can be added in series with the

PFC inductor connection that connects the inductor to the

input rectiﬁer for the purpose of measurement.

3. Thermal check – at maximum output power, minimum input

voltage and maximum ambient temperature; verify that

temperature speciﬁcations are not exceeded for the HiperPFS,

PFC inductor, output diodes and output capacitors. Enough

thermal margin should be allowed for the part-to-part

variation of the RDS(ON) of HiperPFS, as speciﬁed in the data

sheet. A maximum package temperature of 100 °C is

recommended to allow for these variations.

4. Input PF should improve with load, if performance is found to

progressively deteriorate with loading then that is a sign of

possible noise pickup by the VOLTAGE MONITOR pin circuit

or the feedback divider network and the compensation

circuit.

Rev. D 03/12

PFS704-729EG

www.powerint.com

Parameter Symbol

Conditions

SOURCE = 0 V, VCC = 12 V,

TC = -40 °C to 125 °C

(Note D) (Unless Otherwise Speciﬁed)

Min Typ Max Units

Control Functions

Maximum Operating

ON-time tON(MAX) 0 °C < TC < 100 °C 30 40 50

Minimum Operating

ON-time tON(MIN)

See Note A

0 °C < TC < 100 °C 0 1

Maximum Operating

OFF-time tOFF(MAX) 0 °C < TC < 100 °C 30 40 50

Minimum Operating

OFF-time tOFF(MIN) 0 °C < TC < 100 °C 1 3

Internal Feedback

Voltage Reference VREF

TC = 25 °C

See Note A 5.955 6.00 6.045 V

FEEDBACK Pin

Voltage VFB

0 °C < TC < 100 °C

(In Regulation) 5.82 6.00 6.18 V

FEEDBACK Pin

Current IFB TC = 25 °C 340 500 640 nA

Soft-Start Time tSOFT TC = 25 °C 12 ms

Internal Compensation

Frequency fCOMP

See Note A

Pole (fp) 1 kHz

Error-Ampliﬁer Gain AvSee Note A 100 -

Absolute Maximum Ratings(2)

DRAIN Pin Peak Current: PFS704 ................................... .........7.5 A

PFS706 ......................................9.0 A

PFS708 .................................... 11.3 A

PFS710 ....................................13.5 A

PFS712 ....................................15.8 A

PFS714 ....................................18.0 A

PFS716 ....................................21.0 A

PFS723 ...................................... 7.5 A

PFS724 ......................................9.0 A

PFS725 .................................... 11.3 A

PFS726 ....................................13.5 A

PFS727 ....................................15.8 A

PFS728 ....................................18.0 A

PFS729 .................................... 21.0 A

DRAIN Pin Voltage ..................................... ...............-0.3 V to 530 V

VCC Pin Voltage ...................... ............................ -0.3 V to 13.4 V

VCC Pin Current .............................................................. 25 mA

VOLTAGE MONITOR Pin Voltage ................................-0.3 V to 9 V

FEEDBACK Pin Voltage .......................................... -0.3 V to 9 V

Storage Temperature ...................................... ..... -65 °C to 150 °C

Operating Junction Temperature(3) ....................-40 °C to 150 °C

Lead Temperature(4) ........................................................260 °C

Notes:

1. All voltages referenced to SOURCE, TA = 25 °C.

2. Maximum ratings speciﬁed may be applied one at a time

without causing permanent damage to the product. Expo-

sure to Absolute Maximum Rating conditions for extended

periods of time may affect product reliability.

3. Normally limited by internal circuitry.

4. 1/16 in. from case for 5 seconds.

Thermal Resistance

Thermal Resistance: e Package:

(qJA)(1) ....................................................103 °C/W

(qJC).................................................. (see Figure 20)

Notes:

1. MOSFET only – controller junction temperature (TC) may be

less than the power MOSFET junction temperature (TM).

Rev. D 03/12

PFS704-729EG

www.powerint.com

Parameter Symbol

Conditions

SOURCE = 0 V, VCC = 12 V,

TC = -40 °C to 125 °C

(Note D) (Unless Otherwise Speciﬁed)

Min Typ Max Units

Line-Sense/Peak Detector

Brown-In

Threshold Current IUV+ 0 °C < TC < 100 °C 27.50 28.88 mA

Brown-Out

Threshold Current IUV- 0 °C < TC < 100 °C 22.52 24.50 mA

Brown-In/Out

Hysteresis IUV(HYST) TC = 25 °C 1 5.5 mA

Soft-Start Brown-Out

Threshold Current IUV-SS TC = 25 °C 20.5 22.5 24.5 mA

VOLTAGE MONITOR

Pin Voltage Threshold VV(THR)

0 °C < TC < 100 °C

IV = IUV+

2.3 V

VOLTAGE MONITOR

Pin Short-Circuit

Current

IV(SC)

0 °C < TC < 100 °C

VV = 6 V 350 mA

VOLTAGE MONITOR

Pin Pre-Soft-Start

Current

IV(SS)

0 °C < TC < 100 °C

VV = 3 V 6 mA

Maximum Line Sample

Refresh Period TREFRESH TC = 25 °C 30 60 ms

VOLTAGE MONITOR

Pin Shutdown Current

Threshold

IV(OFF) 0 °C < TC < 100 °C 200 mA

VOLTAGE MONITOR

Pin Shutdown Delay tV(OFF) TC = 25 °C 65 110 135 ms

Rev. D 03/12

PFS704-729EG

www.powerint.com

Parameter Symbol

Conditions

SOURCE = 0 V, VCC = 12 V,

TC = -40 °C to 125 °C

(Note D) (Unless Otherwise Speciﬁed)

Min Typ Max Units

Current Limit/Circuit Protection

Over-Current

Protection IOCP

PFS704

di/dt = 250 mA/ms

TC = 25 °C

IV < 48 mA 3.8 4.1 4.3

IV > 59 mA 2.5 2.7 2.8

PFS706

di/dt = 300 mA/ms

TC = 25 °C

IV < 48 mA 4.5 4.8 5.1

IV > 59 mA 3.0 3.2 3.4

PFS708

di/dt = 400 mA/ms

TC = 25 °C

IV < 48 mA 5.5 5.9 6.2

IV > 59 mA 3.7 4.0 4.2

PFS710

di/dt = 500 mA/ms

TC = 25 °C

IV < 48 mA 6.8 7.2 7.5

IV > 59 mA 4.6 4.9 5.1

PFS712

di/dt = 650 mA/ms

TC = 25 °C

IV < 48 mA 8.0 8.4 8.8

IV > 59 mA 5.4 5.7 6.0

PFS714

di/dt = 800 mA/ms

TC = 25 °C

IV < 48 mA 9.0 9.5 9.9

IV > 59 mA 6.0 6.3 6.6

PFS716

di/dt = 920 mA/ms

TC = 25 °C

IV < 48 mA 9.5 10.0 10.5

IV > 59 mA 6.3 6.7 7.0

PFS723

di/dt = 250 mA/ms

TC = 25 °C

3.8 4.1 4.3

PFS724

di/dt = 300 mA/ms

TC = 25 °C

4.5 4.8 5.1

PFS725

di/dt = 400 mA/ms

TC = 25 °C

5.5 5.9 6.2

PFS726

di/dt = 500 mA/ms

TC = 25 °C

6.8 7.2 7.5

PFS727

di/dt = 650 mA/ms

TC = 25 °C

8.0 8.4 8.8

PFS728

di/dt = 800 mA/ms

TC = 25 °C

9.0 9.5 9.9

PFS729

di/dt = 920 mA/ms

TC = 25 °C

9.7 10.2 10.7

Rev. D 03/12

PFS704-729EG

www.powerint.com

Parameter Symbol

Conditions

SOURCE = 0 V, VCC = 12 V,

TC = -40 °C to 125 °C

(Note D) (Unless Otherwise Speciﬁed)

Min Typ Max Units

Current Limit/Circuit Protection (cont.)

SOA Protection

Time-out tOCP TC = 25 °C 200 280 360 ms

SOA On-time tSOA See Note A 1 ms

Leading Edge

Blanking Time tLEB See Note A 220 ns

Current Limit Delay tIL(D) See Note A 100 ns

LEB + ILD + Driver Delay tLEB + tIL(D) +

tDRIVER

TC = 25 °C 370 470 570 ns

Thermal Shutdown

Temperature TSHUT See Note A 111 118 126 °C

Thermal Shutdown

Hysteresis THYST See Note A 50 °C

FEEDBACK Pin

Undervoltage FBUV TC = 25 °C 3 3.5 4 V

FEEDBACK Pin

Undervoltage Delay tFB(UV) TC = 25 °C 65 110 135 ms

FEEDBACK Pin

Overvoltage Threshold

and Hysteresis

FBOV

0 °C < TC < 100 °C

Threshold

VFB

+40 mV

VFB

+90 mV

VFB

+160 mV V

0 °C < TC < 100 °C

Hysteresis 75 mV

FEEDBACK Pin

Overvoltage Delay tFB(OV) TC = 25 °C 1 2 3 ms

FEEDBACK Pin

Start-Up Threshold FBOFF 0 °C < TC < 100 °C 0.5 1.2 1.65 V

FEEDBACK Pin

OFF Delay tFB(OFF) 0 °C < TC < 100 °C 0.5 2 4 ms

Start-Up VCC

(Rising Edge) VCC+ TC = 25 °C 9.5 10.2 V

Shutdown VCC

(Falling Edge) VCC- TC = 25 °C 9.0 9.5 V

VCC Hysteresis VCC(HYST) TC = 25 °C 0.2 0.5 0.8 V

Supply Current

Characteristics

ICD1

0 °C < TC < 100 °C

Switching 3.5

ICD2

0 °C < TC < 100 °C

Not Switching 1.5

VCC Power-Up

Reset Threshold VCC(POR) TC = 25 °C 2.85 3.6 4.25 V

VCC Power-Up

Reset Current IVCC(POR) TC = 25 °C 1.5 mA

Rev. D 03/12

PFS704-729EG

www.powerint.com

Parameter Symbol

Conditions

SOURCE = 0 V, VCC = 12 V,

TC = -40 °C to 125 °C

(Note D) (Unless Otherwise Speciﬁed)

Min Typ Max Units

Power MOSFET

ON-State Resistance RDS(ON)

PFS704

ID = IOCP × 0.5

See Note E

TM = 25 °C 0.61 0.72

TM = 100 °C 1.16

PFS706

TM = 25 °C 0.52 0.61

TM = 100 °C 0.97

PFS708

TM = 25 °C 0.41 0.48

TM = 100 °C 0.77

PFS710

TM = 25 °C 0.35 0.41

TM = 100 °C 0.65

PFS712

TM = 25 °C 0.30 0.35

TM = 100 °C 0.55

PFS714

TM = 25 °C 0.26 0.31

TM = 100 °C 0.48

PFS716

TM = 25 °C 0.22 0.26

TM = 100 °C 0.42

PFS723

TM = 25 °C 0.58 0.69

TM = 100 °C 1.10

PFS724

TM = 25 °C 0.49 0.58

TM = 100 °C 0.92

PFS725

TM = 25 °C 0.39 0.46

TM = 100 °C 0.73

PFS726

TM = 25 °C 0.33 0.39

TM = 100 °C 0.62

PFS727

TM = 25 °C 0.28 0.33

TM = 100 °C 0.52

PFS728

TM = 25 °C 0.25 0.29

TM = 100 °C 0.46

PFS729

TM = 25 °C 0.21 0.25

TM = 100 °C 0.40

Rev. D 03/12

PFS704-729EG

www.powerint.com

Parameter Symbol

Conditions

SOURCE = 0 V, VCC = 12 V,

TC = -40 °C to 125 °C

(Note D) (Unless Otherwise Speciﬁed)

Min Typ Max Units

Power MOSFET (cont.)

Effective Output

Capacitance COSS

TC = 25 °C,

VGS = 0 V,

VDS = 0 to 80%

VDSS

See Note A

PFS704 176

PFS706 210

PFS708 265

PFS710 312

PFS712 320

PFS714 420

PFS716 487

PFS723 185

PFS724 221

PFS725 278

PFS726 328

PFS727 389

PFS728 441

PFS729 511

Breakdown Voltage BVDSS

TM = 25 °C, VCC = 12 V

ID = 250 mA, VFB = VV = 0 V 530 V

Breakdown Voltage

Temperature

Coefﬁcient

BVDSS(TC) 1.2 %/25°C

Rev. D 03/12

PFS704-729EG

www.powerint.com

NOTES:

A. Not a tested parameter. Guaranteed by design.

B. Tested in typical boost PFC application circuit with 0.1 mF capacitor between the V pin and G pin and a 4 MW resistor from

rectiﬁed line to the V pin for PFS70x and PFS71x.

C. Tested in typical boost PFC application circuit with 0.047 mF capacitor between the V pin and G pin and a 9 MW resistor from

rectiﬁed line to the V pin for PFS72x.

D. Normally limited by internal circuitry.

E. Refer to IOCP with IV <48 mA for PFS704-716.

Parameter Symbol

Conditions

SOURCE = 0 V, VCC = 12 V,

TC = -40 °C to 125 °C

(Note D) (Unless Otherwise Speciﬁed)

Min Typ Max Units

Power MOSFET (cont.)

OFF-State Drain

Current Leakage IDSS

TM = 100 °C

VDS = 80% BVDSS

VCC = 12 V

VFB = VV = 0

PFS704 80

PFS706 100

PFS708 120

PFS710 150

PFS712 170

PFS714 200

PFS716 235

PFS723 84

PFS724 105

PFS725 126

PFS726 158

PFS727 179

PFS728 210

PFS729 247

Turn-Off Voltage

Rise Time tR

See Note A, B, C

Turn-On Voltage

Fall Time tF100

Start-up Time Delay tSTART-DELAY

0 °C < TC < 100 °C

See Note A, B, C 2 6 10 ms

Rev. D 03/12

PFS704-729EG

www.powerint.com

Typical Performance Characteristics

0PFS704

PFS723

PFS706

PFS724

PFS708

PFS725

PFS710

PFS726

PFS712

PFS727

PFS714

PFS728

PFS716

PFS729

Thermal Resistance θJC (°C/W)

2.5

1.5

0.5

PI-6234-110510

Figure 20. Thermal Resistance (qJC ).

Figure 21. Typical Characteristic: VOLTAGE MONITOR Pin Voltage vs. Current.

Figure 22. Typical Characteristic: FEEDBACK Pin Current vs. Voltage.

0 50 100 150 200 250 300

VOLTAGE MONITOR Pin Voltage (V)

VOLTAGE MONITOR Pin Current (µA)

PI-6239-111010

0 321 4 5 76 8 9 10 11 12 13 14

FEEDBACK Pin Current (µA)

FEEDBACK Pin Voltage (V)

-5

PI-6240-110810

Rev. D 03/12

PFS704-729EG

www.powerint.com

Typical Performance Characteristics (cont.)

Figure 23. Typical Characteristic: VCC Pin Current vs. Voltage (Device not Switching).

0 321 4 5 76 8 9 10 11 12 13 14

VCC Pin Current (mA)

VCC Pin Voltage (V)

1.2

0.6

0.4

0.8

0.2

-5

PI-6241-111010

Rev. D 03/12

PFS704-729EG

www.powerint.com

PI-5711-110810

Notes:

1. Dimensioning and tolerancing per ASME Y14.5M-1994.

2. Dimensions noted are determined at the outermost extremes of the plastic body exclusive of mold

flash, tie bar burrs, gate burrs, and interlead flash, but including any mismatch between the top

and bottom of the plastic body. Maximum mold protrusion is 0.007 (0.18) per side.

3. Dimensions noted are inclusive of plating thickness.

4. Does not include interlead flash or protrusions.

5. Controlling dimensions in inches (mm).

eSIP-7G (E Package)

0.378 (9.60)

Ref.

0.019 (0.48) Ref.

0.027 (0.70)

0.023 (0.58)

0.020 (0.50)

0.060 (1.52)

Ref.

10° Ref.

All Around

0.016 (0.41)

Ref.

0.290 (7.37)

Ref.

Detail A

0.047 (1.19)

0.050 (1.27) 0.070 (1.78) Ref.

Pin 1 I.D.

0.118 (3.00)

FRONT VIEW SIDE VIEW BACK VIEW

Detail AEND VIEW

0.140 (3.56)

0.120 (3.05)

0.081 (2.06)

0.077 (1.96)

6×

0.016 (0.41)

0.011 (0.28)

0.020 M 0.51 M C

0.403 (10.24)

0.397 (10.08)

0.021 (0.53)

0.019 (0.48)

0.048 (1.22)

0.046 (1.17)

0.325 (8.25)

0.320 (8.13)

0.221 (5.61)

Ref.

0.519 (13.18)

Ref.

0.100 (2.54)

0.211 (5.36)

Ref.

0.207 (5.26)

0.187 (4.75)

6×

0.033 (0.84)

0.028 (0.71)

0.010 M 0.25 M C A B

A A 3

MOUNTING HOLE PATTERN (not to scale)

PIN 7

PIN 1

0.100 (2.54) 0.100 (2.54)

0.059 (1.50)

0.050 (1.27)

0.100 (2.54)

0.155 (3.93)

Rev. D 03/12

PFS704-729EG

www.powerint.com

Part Marking Information

• HiperPFS Product Family

• PFS Series Number

• Package Identier

E Plastic eSIP-7G

• Pin Finish

G Halogen Free and RoHS Compliant

Part Ordering Information

Part Number Option Quantity

PFS704EG Tube 48

PFS706EG Tube 48

PFS708EG Tube 48

PFS710EG Tube 48

PFS712EG Tube 48

PFS714EG Tube 48

PFS716EG Tube 48

PFS723EG Tube 48

PFS724EG Tube 48

PFS725EG Tube 48

PFS726EG Tube 48

PFS727EG Tube 48

PFS728EG Tube 48

PFS729EG Tube 48

PFS 704 E G

Revision Notes Date

A Initial Release. 11/09/10

B Updated Figure 9 and deleted sentence on page 7. 02/11

C Updated FEEDBACK pin voltage rating in Absolute Maximum Rating table. 02/11

D Updated Inductor Design paragraph on page 12. Updated KP number on page 13. 12/11

D Updated Parameter Table text. 03/21/12

For the latest updates, visit our website: www.powerint.com

Power Integrations reserves the right to make changes to its products at any time to improve reliability or manufacturability. Power

Integrations does not assume any liability arising from the use of any device or circuit described herein. POWER INTEGRATIONS MAKES

NO WARRANTY HEREIN AND SPECIFICALLY DISCLAIMS ALL WARRANTIES INCLUDING, WITHOUT LIMITATION, THE IMPLIED

WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS.

Patent Information

The products and applications illustrated herein (including transformer construction and circuits external to the products) may be covered

by one or more U.S. and foreign patents, or potentially by pending U.S. and foreign patent applications assigned to Power Integrations. A

complete list of Power Integrations patents may be found at www.powerint.com. Power Integrations grants its customers a license under

certain patent rights as set forth at http://www.powerint.com/ip.htm.

Life Support Policy

POWER INTEGRATIONS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR

SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF POWER INTEGRATIONS. As used herein:

1. A Life support device or system is one which, (i) is intended for surgical implant into the body, or (ii) supports or sustains life, and (iii)

whose failure to perform, when properly used in accordance with instructions for use, can be reasonably expected to result in signiﬁcant

injury or death to the user.

2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause

the failure of the life support device or system, or to affect its safety or effectiveness.

The PI logo, TOPSwitch, TinySwitch, LinkSwitch, DPA-Switch, PeakSwitch, CAPZero, SENZero, LinkZero, HiperPFS, HiperTFS, HiperLCS,

Qspeed, EcoSmart, Clampless, E-Shield, Filterfuse, StakFET, PI Expert and PI FACTS are trademarks of Power Integrations, Inc. Other

Power Integrations Worldwide Sales Support Locations

World Headquarters

5245 Hellyer Avenue

San Jose, CA 95138, USA.

Main: +1-408-414-9200

Customer Service:

Phone: +1-408-414-9665

Fax: +1-408-414-9765

e-mail: usasales@powerint.com

China (Shanghai)

Rm 1601/1610, Tower 1,

Kerry Everbright City

No. 218 Tianmu Road West,

Shanghai, P.R.C. 200070

Phone: +86-21-6354-6323

Fax: +86-21-6354-6325

e-mail: chinasales@powerint.com

China (ShenZhen)

3rd Floor, Block A,

Zhongtou International Business

Center, No. 1061, Xiang Mei Rd,

FuTian District, ShenZhen,

China, 518040

Phone: +86-755-8379-3243

Fax: +86-755-8379-5828

e-mail: chinasales@powerint.com

Germany

Lindwurmstrasse 114

80337 Munich

Germany

Phone: +49-895-527-39110

Fax: +49-895-527-39200

e-mail: eurosales@powerint.com

India

#1, 14th Main Road

Vasanthanagar

Bangalore-560052 India

Phone: +91-80-4113-8020

Fax: +91-80-4113-8023

e-mail: indiasales@powerint.com

Italy

Via Milanese 20, 3rd. Fl.

20099 Sesto San Giovanni (MI)

Italy

Phone: +39-024-550-8701

Fax: +39-028-928-6009

e-mail: eurosales@powerint.com

Japan

Kosei Dai-3 Bldg.

2-12-11, Shin-Yokomana,

Kohoku-ku

Yokohama-shi Kanagwan

222-0033 Japan

Phone: +81-45-471-1021

Fax: +81-45-471-3717

e-mail: japansales@powerint.com

Korea

RM 602, 6FL

Korea City Air Terminal B/D, 159-6

Samsung-Dong, Kangnam-Gu,

Seoul, 135-728, Korea

Phone: +82-2-2016-6610

Fax: +82-2-2016-6630

e-mail: koreasales@powerint.com

Singapore

51 Newton Road

#15-08/10 Goldhill Plaza

Singapore, 308900

Phone: +65-6358-2160

Fax: +65-6358-2015

e-mail: singaporesales@powerint.com

Taiwan

5F, No. 318, Nei Hu Rd., Sec. 1

Nei Hu Dist.

Taipei, Taiwan 114, R.O.C.

Phone: +886-2-2659-4570

Fax: +886-2-2659-4550

e-mail: taiwansales@powerint.com

Europe HQ

1st Floor, St. James’s House

East Street, Farnham

Surrey GU9 7TJ

United Kingdom

Phone: +44 (0) 1252-730-141

Fax: +44 (0) 1252-727-689

e-mail: eurosales@powerint.com

Applications Hotline

World Wide +1-408-414-9660

Applications Fax

World Wide +1-408-414-9760