CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers PRODUCT FEATURES Datasheet General Description Applications The CAP1126, which incorporates SMSC's RightTouch(R) 1 technology, is a multiple channel Capacitive Touch sensor with multiple power LED drivers. It contains six (6) individual capacitive touch sensor inputs with programmable sensitivity for use in touch sensor applications. Each sensor input automatically recalibrates to compensate for gradual environmental changes. Desktop and Notebook PCs LCD Monitors Consumer Electronics Appliances Features Six (6) Capacitive Touch Sensor Inputs -- Programmable sensitivity -- Automatic recalibration -- Individual thresholds for each button The CAP1126 also contains two (2) LED drivers that offer full-on / off, variable rate blinking, dimness controls, and breathing. Each of the LED drivers may be linked to one of the sensor inputs to be actuated when a touch is detected. As well, each LED driver may be individually controlled via a host controller. The CAP1126 includes Multiple Pattern Touch recognition that allows the user to select a specific set of buttons to be touched simultaneously. If this pattern is detected, then a status bit is set and an interrupt generated. Proximity Detection Multiple Button Pattern Detection Calibrates for Parasitic Capacitance Analog Filtering for System Noise Sources Press and Hold feature for Volume-like Applications Multiple Communication Interfaces -- -- -- -- Additionally, the CAP1126 includes circuitry and support for enhanced sensor proximity detection. The CAP1126 offers multiple power states operating at low quiescent currents. In the Standby state of operation, one or more capacitive touch sensor inputs are active and all LEDs may be used. If a touch is detected, it will wake the system using the WAKE/SPI_MOSI pin. SMBus / I2C compliant interface SMSC BC-Link interface SPI communications Pin selectable communications protocol and multiple slave addresses (SMBus / I2C only) Low Power Operation -- 5uA quiescent current in Deep Sleep -- 50uA quiescent current in Standby (1 sensor input monitored) -- Samples one or more channels in Standby Deep Sleep is the lowest power state available, drawing 5uA (typical) of current. In this state, no sensor inputs are active. Driving the WAKE/SPI_MOSI pin or communications will wake the device. Two (2) LED Driver Outputs -- Open Drain or Push-Pull -- Programmable blink, breathe, and dimness controls -- Can be linked to Capacitive Touch Sensor inputs 1. SMSC, the SMSC logo and RightTouch are registered trademarks and the RightTouch logo is a trademark of Standard Microsystems Corporation ("SMSC"). Dedicated Wake output flags touches in low power state System RESET pin Available in 16-pin 4mm x 4mm RoHS compliant QFN package Block Diagram LED1 LED2 RESET VDD GND WAKE / SPI_MOSI SPI_CS# LED Driver, Breathe, and Dimness control SMBus / BC-Link / SPI Slave Protocol Capacitive Touch Sensing Algorithm SMCLK BC_CLK / SPI_CLK SMDATA BC_DATA / SPI_MSIO / SPI_MISO ALERT# / BC_IRQ# ADDR_COMM CS1 SMSC CAP1126 CS2 CS3 CS4 CS5 CS6 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Ordering Information: ORDERING NUMBER CAP1126-1-AP-TR PACKAGE FEATURES 16-pin QFN 4mm x 4mm (Lead-free RoHS compliant) Six capacitive touch sensor inputs, Two LED drivers, Dedicated Wake, Reset, SMBus / BC-Link / SPI interfaces Reel size is 4,000 pieces This product meets the halogen maximum concentration values per IEC61249-2-21 For RoHS compliance and environmental information, please visit www.smsc.com/rohs Please contact your SMSC sales representative for additional documentation related to this product such as application notes, anomaly sheets, and design guidelines. Copyright (c) 2012 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC's website at http://www.smsc.com. SMSC is a registered trademark of Standard Microsystems Corporation ("SMSC"). Product names and company names are the trademarks of their respective holders. The Microchip name and logo, and the Microchip logo are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT; TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Revision 1.32 (01-05-12) 2 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table of Contents Chapter 1 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Chapter 2 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Chapter 3 Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1.1 SMBus (I2C) Communications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1.2 SPI Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1.3 BC-Link Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Management Bus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2.1 SMBus Start Bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2.2 SMBus Address and RD / WR Bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2.3 SMBus Data Bytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2.4 SMBus ACK and NACK Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2.5 SMBus Stop Bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2.6 SMBus Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2.7 SMBus and I2C Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SMBus Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3.1 SMBus Write Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3.2 SMBus Read Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3.3 SMBus Send Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3.4 SMBus Receive Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I2C Protocols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4.1 Block Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4.2 Block Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPI Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5.1 SPI Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5.2 SPI Bi-Directional Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5.3 SPI_CS# Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5.4 Address Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5.5 SPI Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Normal SPI Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6.1 Reset Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6.2 Set Address Pointer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6.3 Write Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6.4 Read Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bi-Directional SPI Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7.1 Reset Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7.2 Set Address Pointer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7.3 Write Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7.4 Read Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BC-Link Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 17 17 17 18 18 18 18 18 19 19 19 19 20 20 20 20 21 21 21 21 22 22 22 23 23 23 24 25 25 26 27 27 27 28 28 29 Chapter 4 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 4.1 4.2 4.3 4.4 4.5 Power States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RESET Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WAKE/SPI_MOSI Pin Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.1 Linking LEDs to Capacitive Touch Sensor Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Capacitive Touch Sensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SMSC CAP1126 3 DATASHEET 31 32 32 32 33 33 Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet 4.6 4.5.1 Sensing Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5.2 Recalibrating Sensor Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5.3 Proximity Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5.4 Multiple Touch Pattern Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5.5 Low Frequency Noise Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5.6 RF Noise Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ALERT# Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.6.1 Sensor Interrupt Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 33 34 34 34 35 35 35 Chapter 5 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.11 5.12 5.13 5.14 5.15 5.16 5.17 5.18 5.19 5.20 5.21 5.22 5.23 5.24 5.25 5.26 5.27 5.28 5.29 5.30 5.31 5.32 5.33 5.34 5.35 5.36 5.37 5.38 5.39 Main Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2.1 General Status - 02h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2.2 Sensor Input Status - 03h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2.3 LED Status - 04h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Noise Flag Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Delta Count Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensitivity Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.6.1 Configuration - 20h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.6.2 Configuration 2 - 44h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Enable Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Configuration Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Configuration 2 Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Averaging and Sampling Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Calibration Activate Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interrupt Enable Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Repeat Rate Enable Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multiple Touch Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multiple Touch Pattern Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multiple Touch Pattern Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recalibration Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Threshold Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Noise Threshold Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standby Channel Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standby Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standby Sensitivity Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standby Threshold Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Base Count Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Output Type Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input LED Linking Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Polarity Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Output Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Linked LED Transition Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Mirror Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Behavior Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Pulse 1 Period Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Pulse 2 Period Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Breathe Period Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Duty Cycle Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Direct Ramp Rates Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Off Delay Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Calibration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Revision 1.32 (01-05-12) 4 DATASHEET 41 42 42 42 43 43 44 44 46 46 47 48 48 50 51 53 53 54 54 55 56 57 59 59 60 60 62 63 63 64 64 65 66 67 68 68 70 72 73 74 75 76 77 80 SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet 5.40 5.41 5.42 Product ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Manufacturer ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Revision Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Chapter 6 Package Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 6.1 6.2 CAP1126 Package Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Package Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Appendix A Device Delta . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 A.1 Delta from CAP1026 to CAP1126 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Chapter 7 Datasheet Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 SMSC CAP1126 5 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet List of Figures Figure 1.1 Figure 3.1 Figure 3.2 Figure 3.3 Figure 3.4 Figure 3.5 Figure 3.6 Figure 3.7 Figure 3.8 Figure 3.9 Figure 3.10 Figure 3.11 Figure 3.12 Figure 4.1 Figure 4.2 Figure 4.3 Figure 5.1 Figure 5.2 Figure 5.3 Figure 5.4 Figure 5.5 Figure 5.6 Figure 5.7 Figure 5.8 Figure 6.1 Figure 6.2 Figure 6.3 Figure 6.4 CAP1126 Pin Diagram (16-Pin QFN). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SMBus Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPI Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Example SPI Bus Communication - Normal Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPI Reset Interface Command - Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPI Set Address Pointer Command - Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPI Write Command - Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPI Read Command - Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPI Read Command - Normal Mode - Full. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPI Reset Interface Command - Bi-directional Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPI Set Address Pointer Command - Bi-directional Mode . . . . . . . . . . . . . . . . . . . . . . . . . SPI Write Data Command - Bi-directional Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPI Read Data Command - Bi-directional Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Diagram for CAP1126 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Interrupt Behavior - Repeat Rate Enabled. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Interrupt Behavior - No Repeat Rate Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pulse 1 Behavior with Non-Inverted Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pulse 1 Behavior with Inverted Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pulse 2 Behavior with Non-Inverted Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pulse 2 Behavior with Inverted Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Breathe Behavior with Non-Inverted Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Breathe Behavior with Inverted Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Direct Behavior for Non-Inverted Polarity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Direct Behavior for Inverted Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-Pin QFN 4mm x 4mm Package Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-Pin QFN 4mm x 4mm Package Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-Pin QFN 4mm x 4mm PCB Footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CAP1126 Package Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Revision 1.32 (01-05-12) 6 DATASHEET 10 18 22 24 25 25 26 26 27 27 28 28 28 31 35 36 71 71 73 73 77 78 79 79 82 83 83 84 SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet SMSC CAP1126 7 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet List of Tables Table 1.1 Table 1.2 Table 2.1 Table 2.2 Table 3.1 Table 3.2 Table 3.3 Table 3.4 Table 3.5 Table 3.6 Table 3.7 Table 3.8 Table 5.1 Table 5.2 Table 5.3 Table 5.4 Table 5.5 Table 5.6 Table 5.7 Table 5.8 Table 5.9 Table 5.10 Table 5.11 Table 5.12 Table 5.13 Table 5.14 Table 5.15 Table 5.16 Table 5.17 Table 5.18 Table 5.19 Table 5.20 Table 5.21 Table 5.22 Table 5.23 Table 5.24 Table 5.25 Table 5.26 Table 5.27 Table 5.28 Table 5.29 Table 5.30 Table 5.31 Table 5.32 Table 5.33 Table 5.34 Table 5.35 Table 5.36 Table 5.37 Table 5.38 Table 5.39 Table 5.40 Pin Description for CAP1126. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute Maximum Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ADDR_COMM Pin Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Protocol Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Write Byte Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Read Byte Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Send Byte Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Receive Byte Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Block Write Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Block Read Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Register Set in Hexadecimal Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Main Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GAIN Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Noise Flag Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Delta Count Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensitivity Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DELTA_SENSE Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BASE_SHIFT Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Enable Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MAX_DUR Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RPT_RATE Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Configuration 2 Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M_PRESS Bit Decode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Averaging and Sampling Configuration Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AVG Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SAMP_TIME Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CYCLE_TIME Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Calibration Activate Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interrupt Enable Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Repeat Rate Enable Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multiple Touch Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B_MULT_T Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multiple Touch Pattern Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MTP_TH Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multiple Touch Pattern Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recalibration Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NEG_DELTA_CNT Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CAL_CFG Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Threshold Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Noise Threshold Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CSx_BN_TH Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standby Channel Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standby Configuration Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . STBY_AVG Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . STBY_SAMP_TIME Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . STBY_CY_TIME Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standby Sensitivity Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Revision 1.32 (01-05-12) 8 DATASHEET 10 12 13 13 17 19 20 20 20 20 21 21 37 41 41 42 43 44 44 45 45 46 48 48 49 49 50 50 51 51 52 52 53 53 54 54 55 55 56 56 57 58 58 59 59 60 60 60 61 61 62 62 SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 5.41 Table 5.42 Table 5.43 Table 5.44 Table 5.45 Table 5.46 Table 5.47 Table 5.48 Table 5.49 Table 5.50 Table 5.51 Table 5.52 Table 5.53 Table 5.54 Table 5.55 Table 5.56 Table 5.57 Table 5.58 Table 5.59 Table 5.60 Table 5.61 Table 5.62 Table 5.63 Table 5.64 Table 5.65 Table 5.66 Table 5.67 Table 5.68 Table 5.69 Table A.1 Table 7.1 SMSC CAP1126 STBY_SENSE Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standby Threshold Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Base Count Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Output Type Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input LED Linking Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Polarity Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Output Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Polarity Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Linked LED Transition Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Mirror Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Behavior Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LEDx_CTL Bit Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Pulse 1 Period Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Pulse / Breathe Period Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Pulse 2 Period Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Breathe Period Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Configuration Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PULSEX_CNT Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Duty Cycle Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Duty Cycle Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Direct Ramp Rates Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rise / Fall Rate Decode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Off Delay Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Breathe Off Delay Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Off Delay Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Input Calibration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vendor ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Revision Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Register Delta From CAP1026 to CAP1126 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Customer Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 DATASHEET 63 63 63 64 64 65 66 67 67 68 68 70 70 72 72 73 74 74 75 75 76 76 77 78 79 80 81 81 81 85 87 Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet VDD CS1 CS2 CS3 15 14 13 8 4 ALERT# / BC_IRQ# SMCLK / BC_CLK / SPI_CLK 7 3 RESET SMDATA / BC_DATA / SPI_MSIO / SPI_MISO CAP1126 16 pin QFN 6 2 LED2 WAKE / SPI_MOSI 5 1 LED1 SPI_CS# 16 Chapter 1 Pin Description 12 CS4 11 CS5 10 CS6 9 ADDR_COMM GND Figure 1.1 CAP1126 Pin Diagram (16-Pin QFN) Table 1.1 Pin Description for CAP1126 PIN NUMBER PIN NAME PIN FUNCTION PIN TYPE 1 SPI_CS# Active low chip-select for SPI bus DI (5V) WAKE - Active high wake / interrupt output Standby power state - requires pull-down resistor DO 2 WAKE / SPI_MOSI Revision 1.32 (01-05-12) DI SPI_MOSI - SPI Master-Out-Slave-In port when used in normal mode DI (5V) 10 Connect to Ground Pull-down Resistor WAKE - Active high wake input - requires pull-down resistor Deep Sleep power state DATASHEET UNUSED CONNECTION Connect to Ground SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 1.1 Pin Description for CAP1126 (continued) PIN NUMBER 3 4 PIN NAME SMDATA / BC_DATA / SPI_MSIO / SPI_MISO SMCLK / BC_CLK / SPI_CLK 5 8 PIN TYPE SMDATA - Bi-directional, open-drain SMBus data requires pull-up resistor DIOD (5V) BC_DATA - Bi-directional, open-drain BC-Link data requires pull-up resistor DIO n/a DIO SPI_MISO - SPI Master-In-Slave-Out port when used in normal mode DO SMCLK - SMBus clock input - requires pull-up resistor DI (5V) BC_CLK - BC-Link clock input DI (5V) SPI_CLK - SPI clock input DI (5V) Open drain LED 1 driver (default) OD (5V) Connect to Ground Push-pull LED 1 driver DO leave open or connect to Ground Open drain LED 2 driver (default) OD (5V) Connect to Ground Push-pull LED 2 driver DO leave open or connect to Ground Active high soft reset for system - resets all registers to default values. If not used, connect to ground. DI (5V) Connect to Ground ALERT# - Active low alert / interrupt output for SMBus alert or SPI interrupt OD (5V) Connect to Ground ALERT# - Active high push-pull alert / interrupt output for SMBus alert or SPI interrupt DO leave open BC_IRQ# - Active low interrupt / optional for BC-Link OD (5V) Connect to Ground BC_IRQ# - Active high push-pull interrupt / optional for BC-Link DO leave open LED2 RESET ALERT# / BC_IRQ# UNUSED CONNECTION SPI_MSIO - SPI Master-Slave-In-Out bidirectional port when used in bi-directional mode LED1 6 7 PIN FUNCTION n/a 9 ADDR_COMM Address / communications select pin - pull-down resistor determines address / communications mechanism AI n/a 10 CS6 Capacitive Touch Sensor Input 6 AIO Connect to Ground 11 CS5 Capacitive Touch Sensor Input 5 AIO Connect to Ground 12 CS4 Capacitive Touch Sensor Input 4 AIO Connect to Ground 13 CS3 Capacitive Touch Sensor Input 3 AIO Connect to Ground SMSC CAP1126 11 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 1.1 Pin Description for CAP1126 (continued) PIN NUMBER PIN NAME PIN FUNCTION PIN TYPE UNUSED CONNECTION 14 CS2 Capacitive Touch Sensor Input 2 AIO Connect to Ground 15 CS1 Capacitive Touch Sensor Input 1 AIO Connect to Ground 16 VDD Positive Power supply Power n/a Bottom Pad GND Ground Power n/a APPLICATION NOTE: When the ALERT# pin is configured as an active low output, it will be open drain. When it is configured as an active high output, it will be push-pull. APPLICATION NOTE: For the 5V tolerant pins that have a pull-up resistor, the pull-up voltage must not exceed 3.6V when the CAP1126 is unpowered. APPLICATION NOTE: The SPI_CS# pin should be grounded when SMBus, I2C, or BC-Link communications are used. The pin types are described in Table 1.2. All pins labeled with (5V) are 5V tolerant. Table 1.2 Pin Types PIN TYPE Power DI AIO DESCRIPTION This pin is used to supply power or ground to the device. Digital Input - This pin is used as a digital input. This pin is 5V tolerant. Analog Input / Output -This pin is used as an I/O for analog signals. DIOD Digital Input / Open Drain Output - This pin is used as a digital I/O. When it is used as an output, it is open drain and requires a pull-up resistor. This pin is 5V tolerant. OD Open Drain Digital Output - This pin is used as a digital output. It is open drain and requires a pull-up resistor. This pin is 5V tolerant. DO Push-pull Digital Output - This pin is used as a digital output and can sink and source current. DIO Push-pull Digital Input / Output - This pin is used as an I/O for digital signals. Revision 1.32 (01-05-12) 12 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Chapter 2 Electrical Specifications Table 2.1 Absolute Maximum Ratings Voltage on 5V tolerant pins (V5VT_PIN) -0.3 to 5.5 V Voltage on 5V tolerant pins (|V5VT_PIN - VDD|) Note 2.2 0 to 3.6 V Voltage on VDD pin -0.3 to 4 V Voltage on any other pin to GND -0.3 to VDD + 0.3 V Package Power Dissipation up to TA = 85C for 16 pin QFN (see Note 2.3) 0.9 W Junction to Ambient (JA) (see Note 2.4) 58 C/W Operating Ambient Temperature Range -40 to 125 C Storage Temperature Range -55 to 150 C ESD Rating, All Pins, HBM 8000 V Note 2.1 Stresses above those listed could cause permanent damage to the device. This is a stress rating only and functional operation of the device at any other condition above those indicated in the operation sections of this specification is not implied. Note 2.2 For the 5V tolerant pins that have a pull-up resistor, the voltage difference between V5VT_PIN and VDD must never exceed 3.6V. Note 2.3 The Package Power Dissipation specification assumes a recommended thermal via design consisting of a 3x3 matrix of 0.3mm (12mil) vias at 1.0mm pitch connected to the ground plane with a 2.1mm x 2.1mm thermal landing. Note 2.4 Junction to Ambient (JA) is dependent on the design of the thermal vias. Without thermal vias and a thermal landing, the JA is approximately 60C/W including localized PCB temperature increase. Table 2.2 Electrical Specifications VDD = 3V to 3.6V, TA = 0C to 85C, all Typical values at TA = 27C unless otherwise noted. CHARACTERISTIC SYMBOL MIN TYP MAX UNIT CONDITIONS DC Power Supply Voltage SMSC CAP1126 VDD 3.0 3.3 3.6 13 DATASHEET V Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 2.2 Electrical Specifications (continued) VDD = 3V to 3.6V, TA = 0C to 85C, all Typical values at TA = 27C unless otherwise noted. CHARACTERISTIC SYMBOL MIN TYP MAX UNIT CONDITIONS uA Standby state active 1 sensor input monitored No LEDs active Default conditions (8 avg, 70ms cycle time) uA Standby state active 1 sensor input monitored No LEDs active 1 avg, 140ms cycle time, Supply Current 120 ISTBY ISTBY 170 50 IDSLEEP 5 15 uA Deep Sleep state active LEDs at 100% or 0% Duty Cycle No communications TA < 40C 3.135 < VDD < 3.465V IDD 500 600 uA Capacitive Sensing Active No LEDs active Capacitive Touch Sensor Inputs Maximum Base Capacitance CBASE Minimum Detectable Capacitive Shift CTOUCH 20 Recommended Cap Shift CTOUCH 0.1 Power Supply Rejection 50 PSR 2 3 10 pF Pad untouched fF Pad touched - default conditions (1 avg, 35ms cycle time, 1x sensitivity) pF Pad touched - Not tested counts /V Untouched Current Counts Base Capacitance 5pF - 50pF Maximum sensitivity Negative Delta Counts disabled All other parameters default Timing RESET Pin Delay tRST_DLY Time to communications ready tCOMM_DLY Time to first conversion ready tCONV_DLY 10 ms 170 15 ms 200 ms LED Drivers 0 100 % Programmable Duty Cycle DUTYLED Drive Frequency fLED Sinking Current ISINK 24 mA VOL = 0.4 Sourcing Current ISOURCE 24 mA VOH = VDD - 0.4 Revision 1.32 (01-05-12) 2 kHz 14 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 2.2 Electrical Specifications (continued) VDD = 3V to 3.6V, TA = 0C to 85C, all Typical values at TA = 27C unless otherwise noted. CHARACTERISTIC Leakage Current SYMBOL MIN TYP MAX ILEAK UNIT CONDITIONS 5 uA powered or unpowered TA < 85C pull-up voltage < 3.6V if unpowered 0.4 V ISINK_IO = 8mA ISOURCE_IO = 8mA I/O Pins Output Low Voltage VOL Output High Voltage VOH VDD 0.4 V Input High Voltage VIH 2.0 V Input Low Voltage VIL 0.8 V Leakage Current ILEAK 5 uA RESET Pin Release to conversion ready tRESET 200 ms 170 powered or unpowered TA < 85C pull-up voltage < 3.6V if unpowered SMBus Timing Input Capacitance CIN Clock Frequency fSMB Spike Suppression tSP Bus Free Time Stop to Start tBUF 1.3 us Start Setup Time tSU:STA 0.6 us Start Hold Time tHD:STA 0.6 us Stop Setup Time tSU:STO 0.6 us Data Hold Time tHD:DAT 0 us When transmitting to the master Data Hold Time tHD:DAT 0.3 us When receiving from the master Data Setup Time tSU:DAT 0.6 us Clock Low Period tLOW 1.3 us Clock High Period tHIGH 0.6 us Clock / Data Fall Time tFALL 300 ns Min = 20+0.1CLOAD ns Clock / Data Rise Time tRISE 300 ns Min = 20+0.1CLOAD ns Capacitive Load CLOAD 400 pF per bus line SMSC CAP1126 5 pF 10 400 kHz 50 ns 15 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 2.2 Electrical Specifications (continued) VDD = 3V to 3.6V, TA = 0C to 85C, all Typical values at TA = 27C unless otherwise noted. CHARACTERISTIC SYMBOL MIN TYP MAX UNIT CONDITIONS BC-Link Timing Clock Period tCLK 250 ns Data Hold Time tHD:DAT 0 ns Data Setup Time tSU:DAT 30 ns Clock Duty Cycle Duty 40 50 60 Data must be valid before clock % SPI Timing Clock Period tP 250 Clock Low Period tLOW 0.4 x tP 0.6 x tP ns Clock High Period tHIGH 0.4 x tP 0.6 x tP ns Clock Rise / Fall time tRISE / tFALL 0.1 x tP ns Data Output Delay tD:CLK 10 ns Data Setup Time tSU:DAT 20 ns Data Hold Time tHD:DAT 20 ns SPI_CS# to SPI_CLK setup time tSU:CS 0 ns Wake Time tWAKE 10 ns 20 us SPI_CS# asserted to CLK assert Note 2.5 The ALERT pin will not glitch high or low at power up if connected to VDD or another voltage. Note 2.6 The SMCLK and SMDATA pins will not glitch low at power up if connected to VDD or another voltage. Revision 1.32 (01-05-12) 16 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Chapter 3 Communications 3.1 Communications The CAP1126 communicates using the 2-wire SMBus or I2C bus, the 2-wire proprietary BC-Link, or the SPI bus. Regardless of communication mechanism, the device functionality remains unchanged. The communications mechanism as well as the SMBus (or I2C) slave address is determined by the resistor connected between the ADDR_COMM pin and ground as shown in Table 3.1. Table 3.1 ADDR_COMM Pin Decode PULL-DOWN RESISTOR (+/- 5%) PROTOCOL USED SMBUS ADDRESS GND SPI Communications using Normal 4-wire Protocol Used n/a 56k SPI Communications using BiDirectional 3-wire Protocol Used n/a 68k BC-Link Communications n/a 3.1.1 82k SMBus / I 2C 0101_100(r/w) 100k SMBus / I2C 0101_011(r/w) 120k SMBus / I2C 0101_010(r/w) 150k SMBus / I2C 0101_001(r/w) VDD I2C 0101_000(r/w) SMBus / SMBus (I2C) Communications When configured to communicate via the SMBus, the CAP1126 supports the following protocols: Send Byte, Receive Byte, Read Byte, Write Byte, Read Block, and Write Block. In addition, the device supports I2C formatting for block read and block write protocols. APPLICATION NOTE: For SMBus/I2C communications, the SPI_CS# pin is not used and should be grounded; any data presented to this pin will be ignored. See Section 3.2 and Section 3.3 for more information on the SMBus bus and protocols respectively. 3.1.2 SPI Communications When configured to communicate via the SPI bus, the CAP1126 supports both bi-directional 3-wire and normal 4-wire protocols and uses the SPI_CS# pin to enable communications. See Section 3.5 and Section 3.6 for more information on the SPI bus and protocols respectively. 3.1.3 BC-Link Communications When BC-Link communications are used, the CAP1126 supports the read byte protocol and the write byte protocol. APPLICATION NOTE: For BC-Link communications, the SPI_CS# pin is not used and should be grounded; any data presented to this pin will be ignored. SMSC CAP1126 17 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet See Section 3.8 for more information on the BC-Link Bus and protocols respectively. APPLICATION NOTE: Upon power up, the CAP1126 will not respond to any communications for up to 15ms. After this time, full functionality is available. 3.2 System Management Bus The CAP1126 communicates with a host controller, such as an SMSC SIO, through the SMBus. The SMBus is a two-wire serial communication protocol between a computer host and its peripheral devices. A detailed timing diagram is shown in Figure 3.1. Stretching of the SMCLK signal is supported; however, the CAP1126 will not stretch the clock signal. TLOW THIGH THD:STA TSU:STO TRISE SMCLK THD:STA TFALL THD:DAT TSU:STA TSU:DAT SMDATA TBUF P S S S - Start Condition P - Stop Condition P Figure 3.1 SMBus Timing Diagram 3.2.1 SMBus Start Bit The SMBus Start bit is defined as a transition of the SMBus Data line from a logic `1' state to a logic `0' state while the SMBus Clock line is in a logic `1' state. 3.2.2 SMBus Address and RD / WR Bit The SMBus Address Byte consists of the 7-bit client address followed by the RD / WR indicator bit. If this RD / WR bit is a logic `0', then the SMBus Host is writing data to the client device. If this RD / WR bit is a logic `1', then the SMBus Host is reading data from the client device. See Table 3.1 for available SMBus addresses. 3.2.3 SMBus Data Bytes All SMBus Data bytes are sent most significant bit first and composed of 8-bits of information. 3.2.4 SMBus ACK and NACK Bits The SMBus client will acknowledge all data bytes that it receives. This is done by the client device pulling the SMBus Data line low after the 8th bit of each byte that is transmitted. This applies to both the Write Byte and Block Write protocols. The Host will NACK (not acknowledge) the last data byte to be received from the client by holding the SMBus data line high after the 8th data bit has been sent. For the Block Read protocol, the Host will ACK each data byte that it receives except the last data byte. Revision 1.32 (01-05-12) 18 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet 3.2.5 SMBus Stop Bit The SMBus Stop bit is defined as a transition of the SMBus Data line from a logic `0' state to a logic `1' state while the SMBus clock line is in a logic `1' state. When the CAP1126 detects an SMBus Stop bit and it has been communicating with the SMBus protocol, it will reset its client interface and prepare to receive further communications. 3.2.6 SMBus Timeout The CAP1126 includes an SMBus timeout feature. Following a 30ms period of inactivity on the SMBus where the SMCLK pin is held low, the device will timeout and reset the SMBus interface. The timeout function defaults to disabled. It can be enabled by setting the TIMEOUT bit in the Configuration register (see Section 5.6, "Configuration Registers"). 3.2.7 SMBus and I2C Compatibility The major differences between SMBus and I2C devices are highlighted here. For more information, refer to the SMBus 2.0 and I2C specifications. For information on using the CAP1126 in an I2C system, refer to SMSC AN 14.0 SMSC Dedicated Slave Devices in I2C Systems. 1. CAP1126 supports I2C fast mode at 400kHz. This covers the SMBus max time of 100kHz. 2. Minimum frequency for SMBus communications is 10kHz. 3. The SMBus client protocol will reset if the clock is held at a logic `0' for longer than 30ms. This timeout functionality is disabled by default in the CAP1126 and can be enabled by writing to the TIMEOUT bit. I2C does not have a timeout. 4. The SMBus client protocol will reset if both the clock and data lines are held at a logic `1' for longer than 200s (idle condition). This function is disabled by default in the CAP1126 and can be enabled by writing to the TIMEOUT bit. I2C does not have an idle condition. 5. I2C devices do not support the Alert Response Address functionality (which is optional for SMBus). 6. I2C devices support block read and write differently. I2C protocol allows for unlimited number of bytes to be sent in either direction. The SMBus protocol requires that an additional data byte indicating number of bytes to read / write is transmitted. The CAP1126 supports I2C formatting only. 3.3 SMBus Protocols The CAP1126 is SMBus 2.0 compatible and supports Write Byte, Read Byte, Send Byte, and Receive Byte as valid protocols as shown below. All of the below protocols use the convention in Table 3.2. Table 3.2 Protocol Format DATA SENT TO DEVICE Data sent SMSC CAP1126 DATA SENT TO THE HOST Data sent 19 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet 3.3.1 SMBus Write Byte The Write Byte is used to write one byte of data to a specific register as shown in Table 3.3. Table 3.3 Write Byte Protocol START SLAVE ADDRESS WR ACK REGISTER ADDRESS ACK REGISTER DATA ACK STOP 1 ->0 YYYY_YYY 0 0 XXh 0 XXh 0 0 -> 1 3.3.2 SMBus Read Byte The Read Byte protocol is used to read one byte of data from the registers as shown in Table 3.4. Table 3.4 Read Byte Protocol START 1->0 SLAVE ADDRESS YYYY_YYY 3.3.3 WR ACK REGISTER ADDRESS ACK START CLIENT ADDRESS RD 0 0 XXh 0 1 ->0 YYYY_YYY 1 ACK 0 REGISTER DATA XXh NACK 1 STOP 0 -> 1 SMBus Send Byte The Send Byte protocol is used to set the internal address register pointer to the correct address location. No data is transferred during the Send Byte protocol as shown in Table 3.5. APPLICATION NOTE: The Send Byte protocol is not functional in Deep Sleep (i.e., DSLEEP bit is set). Table 3.5 Send Byte Protocol START SLAVE ADDRESS WR ACK REGISTER ADDRESS ACK STOP 1 -> 0 YYYY_YYY 0 0 XXh 0 0 -> 1 3.3.4 SMBus Receive Byte The Receive Byte protocol is used to read data from a register when the internal register address pointer is known to be at the right location (e.g., set via Send Byte). This is used for consecutive reads of the same register as shown in Table 3.6. APPLICATION NOTE: The Receive Byte protocol is not functional in Deep Sleep (i.e., DSLEEP bit is set). Table 3.6 Receive Byte Protocol START SLAVE ADDRESS RD ACK REGISTER DATA NACK STOP 1 -> 0 YYYY_YYY 1 0 XXh 1 0 -> 1 Revision 1.32 (01-05-12) 20 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet 3.4 I2C Protocols The CAP1126 supports I2C Block Write and Block Read. The protocols listed below use the convention in Table 3.2. 3.4.1 Block Write The Block Write is used to write multiple data bytes to a group of contiguous registers as shown in Table 3.7. APPLICATION NOTE: When using the Block Write protocol, the internal address pointer will be automatically incremented after every data byte is received. It will wrap from FFh to 00h. Table 3.7 Block Write Protocol START SLAVE ADDRESS WR ACK REGISTER ADDRESS ACK REGISTER DATA ACK 1 ->0 YYYY_YYY 0 0 XXh 0 XXh 0 REGISTER DATA ACK REGISTER DATA ACK ... REGISTER DATA ACK STOP XXh 0 XXh 0 ... XXh 0 0 -> 1 3.4.2 Block Read The Block Read is used to read multiple data bytes from a group of contiguous registers as shown in Table 3.8. APPLICATION NOTE: When using the Block Read protocol, the internal address pointer will be automatically incremented after every data byte is received. It will wrap from FFh to 00h. Table 3.8 Block Read Protocol START SLAVE ADDRESS WR ACK REGISTER ADDRESS ACK START SLAVE ADDRESS RD ACK REGISTER DATA 1->0 YYYY_YYY 0 0 XXh 0 1 ->0 YYYY_YYY 1 0 XXh ACK REGISTER DATA ACK REGISTER DATA ACK REGISTER DATA ACK ... REGISTER DATA NACK STOP 0 XXh 0 XXh 0 XXh 0 ... XXh 1 0 -> 1 3.5 SPI Interface The SMBus has a predefined packet structure, the SPI does not. The SPI Bus can operate in two modes of operation, normal 4-wire mode and bi-directional 3-wire mode. All SPI commands consist of 8-bit packets sent to a specific slave device (identified by the CS pin). The SPI bus will latch data on the rising edge of the clock and the clock and data both idle high. All commands are supported via both operating modes. The supported commands are: Reset Serial interface, set address pointer, write command and read command. Note that all other codes received during the command phase are ignored and have no effect on the operation of the device. SMSC CAP1126 21 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet tP tHIGH tLOW SPI_CLK tFALL tRISE tSU:DAT SPI_MSIO or SPI_MOSI or SPI_MISO tD:CLK tHD:DAT Figure 3.2 SPI Timing 3.5.1 SPI Normal Mode The SPI Bus can operate in two modes of operation, normal and bi-directional mode. In the normal mode of operation, there are dedicated input and output data lines. The host communicates by sending a command along the CAP1126 SPI_MOSI data line and reading data on the SPI_MISO data line. Both communications occur simultaneously which allows for larger throughput of data transactions. All basic transfers consist of two 8 bit transactions from the Master device while the slave device is simultaneously sending data at the current address pointer value. Data writes consist of two or more 8-bit transactions. The host sends a specific write command followed by the data to write the address pointer. Data reads consist of one or more 8-bit transactions. The host sends the specific read data command and continues clocking for as many data bytes as it wishes to receive. 3.5.2 SPI Bi-Directional Mode In the bi-directional mode of operation, the SPI data signals are combined into the SPI_MSIO line, which is shared for data received by the device and transmitted by the device. The protocol uses a simple handshake and turn around sequence for data communications based on the number of clocks transmitted during each phase. All basic transfers consist of two 8 bit transactions. The first is an 8 bit command phase driven by the Master device. The second is by an 8 bit data phase driven by the Master for writes, and by the CAP1126 for read operations. The auto increment feature of the address pointer allows for successive reads or writes. The address pointer will return to 00h after reaching FFh. 3.5.3 SPI_CS# Pin The SPI Bus is a single master, multiple slave serial bus. Each slave has a dedicated CS pin (chip select) that the master asserts low to identify that the slave is being addressed. There are no formal addressing options. Revision 1.32 (01-05-12) 22 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet 3.5.4 Address Pointer All data writes and reads are accessed from the current address pointer. In both Bi-directional mode and Full Duplex mode, the Address pointer is automatically incremented following every read command or every write command. The address pointer will return to 00h after reaching FFh. 3.5.5 SPI Timeout The CAP1126 does not detect any timeout conditions on the SPI bus. 3.6 Normal SPI Protocols When operating in normal mode, the SPI bus internal address pointer is incremented depending upon which command has been transmitted. Multiple commands may be transmitted sequentually so long as the SPI_CS# pin is asserted low. Figure 3.3 shows an example of this operation. SMSC CAP1126 23 DATASHEET Revision 1.32 (01-05-12) Revision 1.32 (01-05-12) SPI_CS# SPI_MOSI 7Ah 7Ah 7Dh 41h 7Eh 66h 7Dh 41h 7Fh 7Fh 7Fh 7Fh 7Fh 7Fh 7Dh 40h 7Fh 7Fh SPI_MISO XXh (invalid) XXh (invalid) YYh (invalid) YYh (invalid) XXh (invalid) 45h AAh (invalid) AAh (invalid) 55h (invalid) 66h AAh AAh 55h 80h 43h 78h XXh (invalid) 56h SPI Address Pointer SPI Data output buffer Register Address / Data 41h 45h 00h XXh 40h / 56h 41h / 45h 42h / AAh 43h / 55h 44h / 80h 45h / 43h 46h / 78h 42h AAh 41h 55h 41h 66h 42h AAh 43h 55h 44h 80h 45h 43h 46h 78h 40h 80h 40h 56h 40h / 56h 41h / 45h 42h / AAh 43h / 55h 44h / 80h 45h / 43h 40h / 56h 41h / 66h 42h / AAh 43h / 55h 44h / 80h 45h / 43h 40h / 56h 41h / 66h 42h / AAh 43h / 55h 44h / 80h 45h / 43h 40h / 56h 41h / 66h 42h / AAh 43h / 55h 44h / 80h 45h / 43h 40h / 56h 41h / 66h 42h / AAh 43h / 55h 44h / 80h 45h / 43h 40h / 56h 41h / 66h 42h / AAh 43h / 55h 44h / 80h 45h / 43h 40h / 56h 41h / 66h 42h / AAh 43h / 55h 44h / 80h 45h / 43h 40h / 56h 41h / 66h 42h / AAh 43h / 55h 44h / 80h 45h / 43h 40h / 56h 41h / 66h 42h / AAh 43h / 55h 44h / 80h 45h / 43h 46h / 78h 46h / 78h 46h / 78h 46h / 78h 46h / 78h 46h /78h 46h /78h 46h / 78h 46h /78h Indicates SPI Address pointer incremented 24 DATASHEET Figure 3.3 Example SPI Bus Communication - Normal Mode 3.6.1 Reset Interface Datasheet SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Resets the Serial interface whenever two successive 7Ah codes are received. Regardless of the current phase of the transaction - command or data, the receipt of the successive reset commands resets the Serial communication interface only. All other functions are not affected by the reset operation. 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet SPI_CS# SPI_CLK `0' Master SPDOUT SPI_MOSI `1' `1' `1' `1' `0' `1' `0' `0' Reset - 7Ah `1' `1' `1' `0' `1' `0' Reset - 7Ah Invalid register data SPI_MISO `1' 00h - Internal Data buffer empty Master Drives Slave Drives Figure 3.4 SPI Reset Interface Command - Normal Mode 3.6.2 Set Address Pointer The Set Address Pointer command sets the Address pointer for subsequent reads and writes of data. The pointer is set on the rising edge of the final data bit. At the same time, the data that is to be read is fetched and loaded into the internal output buffer but is not transmitted. SPI_CS# SPI_CLK Master SPDOUT SPI_MOSI `0' `1' `1' `1' `1' `1' `0' Register Address `1' Set Address Pointer - 7Dh Unknown, Invalid Data Unknown, Invalid Data SPI_MISO Master Drives Slave Drives Address pointer set Figure 3.5 SPI Set Address Pointer Command - Normal Mode 3.6.3 Write Data The Write Data protocol updates the contents of the register referenced by the address pointer. As the command is processed, the data to be read is fetched and loaded into the internal output buffer but not transmitted. Then, the register is updated with the data to be written. Finally, the address pointer is incremented. SMSC CAP1126 25 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet SPI_CS# SPI_CLK Master SPDOUT SPI_MOSI Write Command - 7Eh SPI_MISO Unknown, Invalid Data Data to Write Old Data at Current Address Pointer Master Drives Slave Drives 1. Data written at current address pointer 2. Address pointer incremented Figure 3.6 SPI Write Command - Normal Mode 3.6.4 Read Data The Read Data protocol is used to read data from the device. During the normal mode of operation, while the device is receiving data, the CAP1126 is simultaneously transmitting data to the host. For the Set Address commands and the Write Data commands, this data may be invalid and it is recommended that the Read Data command is used. SPI_CS# SPI_CLK Master SPDOUT SPI_MOSI `0' `1' `1' `1' `1' `1' `1' `1' Invalid, Unknown Data * Master Drives `1' `1' `1' `1' `1' `1' `1' Subsequent Read Commands - 7F First Read Command - 7Fh SPI_MISO `0' Data at Current Address Pointer Address Pointer Incremented ** Slave Drives * The first read command after any other command will return invalid data for the first byte. Subsequent read commands will return the data at the Current Address Pointer ** The Address Pointer is incremented 8 clocks after the Read Command has been received. Therefore continually sending Read Commands will result in each command reporting new data. Once Read Commands have been finished, the last data byte will be read during the next 8 clocks for any command Figure 3.7 SPI Read Command - Normal Mode Revision 1.32 (01-05-12) 26 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet 1. Register Read Address updated to Current SPI Read Address pointer. 2. Register Read Address incremented = current address pointer +1 - end result = register address pointer doesn't change 1. Register Read Address incremented = current address pointer + 1 1. Register Read Address updated to Current SPI Read Address pointer SPI_CS# SPI_MISO `0' `1' `1' `1' `1' `1' `1' `1' `0' XXh Read Command - 7Fh Master SPDOUT SPI_MOSI `1' `1' `1' `1' `1' `1' `1' Subsequent Read Commands - 7Fh Data at previously set register address = current SPI_CLK address pointer Data at previously set register address = current address pointer (SPI) Master Drives 1. Output buffer transmitted = data at previous address 1. Register data loaded into pointer + 1 = current address output buffer = data at current pointer address pointer Data at previously set register address = current address pointer (SPI) Slave Drives Register Data loaded into 1. Register data loaded into Output buffer = data at current output buffer = data at current address pointer + 1 address pointer 1. SPI Read Address Incremented = new current 1. Output buffer transmitted = address pointer data at current address pointer 2. Register Read Address +1 Incremented = current address 1. Output buffer transmitted = 2. Flag set to increment SPI data at previous register pointer +1 Read Address at end of next 8 address pointer + 1 = current clocks address pointer 1. Output buffer transmitted = data at current address pointer +1 2. Flag set to increment SPI Read Address at end of next 8 clocks Figure 3.8 SPI Read Command - Normal Mode - Full 3.7 Bi-Directional SPI Protocols 3.7.1 Reset Interface Resets the Serial interface whenever two successive 7Ah codes are received. Regardless of the current phase of the transaction - command or data, the receipt of the successive reset commands resets the Serial communication interface only. All other functions are not affected by the reset operation. SPI_CS# SPI_CLK Master SPDOUT SPI_MSIO `0' `1' `1' `1' `1' `0' `1' `0' `0' `1' `1' `1' `1' `0' `1' `0' Reset - 7Ah Reset - 7Ah Figure 3.9 SPI Reset Interface Command - Bi-directional Mode 3.7.2 Set Address Pointer Sets the address pointer to the register to be accessed by a read or write command. This command overrides the auto-incrementing of the address pointer. SMSC CAP1126 27 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet SPI_CS# SPI_CLK Master SPDOUT SPI_MSIO `0' `1' `1' `1' `1' `1' `0' Register Address `1' Set Address Pointer - 7Dh Figure 3.10 SPI Set Address Pointer Command - Bi-directional Mode 3.7.3 Write Data Writes data value to the register address stored in the address pointer. Performs auto increment of address pointer after the data is loaded into the register. SPI_CS# SPI_CLK Master SPDOUT SPI_MSIO `0' `1' `1' `1' `1' `1' `1' `0' Register Write Data Write Command - 7Eh Figure 3.11 SPI Write Data Command - Bi-directional Mode 3.7.4 Read Data Reads data referenced by the address pointer. Performs auto increment of address pointer after the data is transferred to the Master. SPI_CS# SPI_CLK Master SPDOUT SPI_MSIO `0' `1' `1' `1' `1' `1' `1' Register Read Data `1' Read Command - 7Fh Master Drives Slave Drives Indeterminate Figure 3.12 SPI Read Data Command - Bi-directional Mode Revision 1.32 (01-05-12) 28 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet 3.8 BC-Link Interface The BC-Link is a proprietary bus developed to allow communication between a host controller device to a companion device. This device uses this serial bus to read and write registers and for interrupt processing. The interface uses a data port concept, where the base interface has an address register, data register and a control register, defined in the SMSC's 8051's SFR space. Refer to documentation for the BC-Link compatible host controller for details on how to access the CAP1126 via the BC-Link Interface. SMSC CAP1126 29 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Chapter 4 General Description The CAP1126 is a multiple channel Capacitive Touch sensor with multiple power LED drivers. It contains six (6) individual capacitive touch sensor inputs with programmable sensitivity for use in touch sensor applications. Each sensor input automatically recalibrates to compensate for gradual environmental changes. The CAP1126 also contains two (2) low side (or push-pull) LED drivers that offer full-on / off, variable rate blinking, dimness controls, and breathing. Each of the LED drivers may be linked to one of the sensor inputs to be actuated when a touch is detected. As well, each LED driver may be individually controlled via a host controller. Finally, the device contains a dedicated RESET pin to act as a soft reset by the system. The CAP1126 offers multiple power states. It operates at the lowest quiescent current during its Deep Sleep state. In the low power Standby state, it can monitor one or more channels and respond to communications normally. The device contains a wake pin (WAKE/SPI_MOSI) output to wake the system when a touch is detected in Standby and to wake the device from Deep Sleep. The device communicates with a host controller using the SPI bus, SMSC BC-Link bus, or via SMBus / I2C. The host controller may poll the device for updated information at any time or it may configure the device to flag an interrupt whenever a touch is detected on any sensor pad. A typical system diagram is shown in Figure 4.1. Revision 1.32 (01-05-12) 30 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet SPI_CS# RESET WAKE / SPI_MOSI ALERT# / BC_IRQ# SMCLK / BC_CLK / SPI_CLK 3.3V - 5V SMDATA / BC_DATA / SPI_MSIO / SPI_MISO Embedded Controller VDD ADDR_COMM 3.3V - 5V CAP1126 LED1 LED2 Touch Button CS1 CS2 Touch Button Touch Button CS3 CS4 Touch Button Touch Button CS5 CS6 Touch Button Figure 4.1 System Diagram for CAP1126 4.1 Power States The CAP1126 has three operating states depending on the status of the STBY and DSLEEP bits. When the device transitions between power states, previously detected touches (for inactive channels) are cleared and the status bits reset. SMSC CAP1126 31 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet 1. Fully Active - The device is fully active. It is monitoring all active capacitive sensor inputs and driving all LED channels as defined. 2. Standby - The device is in a lower power state. It will measure a programmable number of channels using the Standby Configuration controls (see Section 5.20 through Section 5.22). Interrupts will still be generated based on the active channels. The device will still respond to communications normally and can be returned to the Fully Active state of operation by clearing the STBY bit. 3. Deep Sleep - The device is in its lowest power state. It is not monitoring any capacitive sensor inputs and not driving any LEDs. All LEDs will be driven to their programmed non-actuated state and no PWM operations will be done. While in Deep Sleep, the device can be awakened by SMBus or SPI communications targeting the device. This will not cause the DSLEEP to be cleared so the device will return to Deep Sleep once all communications have stopped. If the device is not communicating via the 4-wire SPI bus, then during this state of operation, if the WAKE/SPI_MOSI pin is driven high by an external source, the device will clear the DSLEEP bit and return to Fully Active. APPLICATION NOTE: In the Deep Sleep state, the LED output will be either high or low and will not be PWM'd at the min or max duty cycle. APPLICATION NOTE: If the CAP1126 is configured to communicate using the BC-Link protocol, the device does not support Deep Sleep. 4.2 RESET Pin The RESET pin is an active high reset that is driven from an external source. While it is asserted high, all the internal blocks will be held in reset including the communications protocol used. No capacitive touch sensor inputs will be sampled and the LEDs will not be driven. All configuration settings will be reset to default states and all readings will be cleared. The device will be held in Deep Sleep that can only be removed by driving the RESET pin low. This will cause the RESET status bit to be set to a logic `1' and generate an interrupt. 4.3 WAKE/SPI_MOSI Pin Operation The WAKE / SPI_MOSI pin is a multi-function pin depending on device operation. When the device is configured to communicate using the 4-wire SPI bus, this pin is an input. However, when the CAP1126 is placed in Standby and is not communicating using the 4-wire SPI protocol, the WAKE pin is an active high output. In this condition, the device will assert the WAKE/SPI_MOSI pin when a touch is detected on one of its sampled sensor inputs. The pin will remain asserted until the INT bit has been cleared and then it will be de-asserted. When the CAP1126 is placed in Deep Sleep and it is not communicating using the 4-wire SPI protocol, the WAKE/SPI_MOSI pin is monitored by the device as an input. If the WAKE/SPI_MOSI pin is driven high by an external source, the CAP1126 will clear the DSLEEP bit causing the device to return to Fully Active. When the device is placed in Deep Sleep, this pin is a High-Z input and must have a pull-down resistor to GND for proper operation. 4.4 LED Drivers The CAP1126 contains two (2) LED drivers. Each LED driver can be linked to its respective capacitive touch sensor input or it can be controlled by the host. Each LED driver can be configured to operate in one of the following modes with either push-pull or open drain drive. Revision 1.32 (01-05-12) 32 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet 1. Direct - The LED is configured to be on or off when the corresponding input stimulus is on or off (or inverted). The brightness of the LED can be programmed from full off to full on (default). Additionally, the LED contains controls to individually configure ramping on, off, and turn-off delay. 2. Pulse 1 - The LED is configured to "Pulse" (transition ON-OFF-ON) a programmable number of times with programmable rate and min / max brightness. This behavior may be actuated when a press is detected or when a release is detected. 3. Pulse 2 - The LED is configured to "Pulse" while actuated and then "Pulse" a programmable number of times with programmable rate and min / max brightness when the sensor pad is released. 4. Breathe - The LED is configured to transition continuously ON-OFF-ON (i.e. to "Breathe") with a programmable rate and min / max brightness. When an LED is not linked to a sensor and is actuated by the host, there's an option to assert the ALERT# pin when the initiated LED behavior has completed. 4.4.1 Linking LEDs to Capacitive Touch Sensor Inputs All LEDs can be linked to the corresponding capacitive touch sensor input so that when the sensor input detects a touch, the corresponding LED will be actuated at one of the programmed responses. 4.5 Capacitive Touch Sensing The CAP1126 contains six (6) independent capacitive touch sensor inputs. Each sensor input has dynamic range to detect a change of capacitance due to a touch. Additionally, each sensor input can be configured to be automatically and routinely re-calibrated. 4.5.1 Sensing Cycle Each capacitive touch sensor input has controls to be activated and included in the sensing cycle. When the device is active, it automatically initiates a sensing cycle and repeats the cycle every time it finishes. The cycle polls through each active sensor input starting with CS1 and extending through CS6. As each capacitive touch sensor input is polled, its measurement is compared against a baseline "Not Touched" measurement. If the delta measurement is large enough, a touch is detected and an interrupt is generated. The sensing cycle time is programmable (see Section 5.10, "Averaging and Sampling Configuration Register"). 4.5.2 Recalibrating Sensor Inputs There are various options for recalibrating the capacitive touch sensor inputs. Recalibration re-sets the Base Count Registers (Section 5.24, "Sensor Input Base Count Registers") which contain the "not touched" values used for touch detection comparisons. APPLICATION NOTE: The device will recalibrate all sensor inputs that were disabled when it transitions from Standby. Likewise, the device will recalibrate all sensor inputs when waking out of Deep Sleep. 4.5.2.1 Manual Recalibration The Calibration Activate Registers (Section 5.11, "Calibration Activate Register") force recalibration of selected sensor inputs. When a bit is set, the corresponding capacitive touch sensor input will be recalibrated (both analog and digital). The bit is automatically cleared once the recalibration routine has finished. SMSC CAP1126 33 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Note: During this recalibration routine, the sensor inputs will not detect a press for up to 200ms and the Sensor Base Count Register values will be invalid. In addition, any press on the corresponding sensor pads will invalidate the recalibration. 4.5.2.2 Automatic Recalibration Each sensor input is regularly recalibrated at a programmable rate (see Section 5.17, "Recalibration Configuration Register"). By default, the recalibration routine stores the average 64 previous measurements and periodically updates the base "not touched" setting for the capacitive touch sensor input. Note: Automatic recalibration only works when the delta count is below the active sensor input threshold. It is disabled when a touch is detected. 4.5.2.3 Negative Delta Count Recalibration It is possible that the device loses sensitivity to a touch. This may happen as a result of a noisy environment, an accidental recalibration during a touch, or other environmental changes. When this occurs, the base untouched sensor input may generate negative delta count values. The NEG_DELTA_CNT bits (see Section 5.17, "Recalibration Configuration Register") can be set to force a recalibration after a specified number of consecutive negative delta readings. Note: During this recalibration, the device will not respond to touches. 4.5.2.4 Delayed Recalibration It is possible that a "stuck button" occurs when something is placed on a button which causes a touch to be detected for a long period. By setting the MAX_DUR_EN bit (see Section 5.6, "Configuration Registers"), a recalibration can be forced when a touch is held on a button for longer than the duration specified in the MAX_DUR bits (see Section 5.8, "Sensor Input Configuration Register"). Note: Delayed recalibration only works when the delta count is above the active sensor input threshold. If enabled, it is invoked when a sensor pad touch is held longer than the MAX_DUR bit setting. 4.5.3 Proximity Detection Each sensor input can be configured to detect changes in capacitance due to proximity of a touch. This circuitry detects the change of capacitance that is generated as an object approaches, but does not physically touch, the enabled sensor pad(s). When a sensor input is selected to perform proximity detection, it will be sampled from 1x to 128x per sampling cycle. The larger the number of samples that are taken, the greater the range of proximity detection is available at the cost of an increased overall sampling time. 4.5.4 Multiple Touch Pattern Detection The multiple touch pattern (MTP) detection circuitry can be used to detect lid closure or other similar events. An event can be flagged based on either a minimum number of sensor inputs or on specific sensor inputs simultaneously exceeding an MTP threshold or having their Noise Flag Status Register bits set. An interrupt can also be generated. During an MTP event, all touches are blocked (see Section 5.15, "Multiple Touch Pattern Configuration Register"). 4.5.5 Low Frequency Noise Detection Each sensor input has an EMI noise detector that will sense if low frequency noise is injected onto the input with sufficient power to corrupt the readings. If this occurs, the device will reject the corrupted sample and set the corresponding bit in the Noise Status register to a logic `1'. Revision 1.32 (01-05-12) 34 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet 4.5.6 RF Noise Detection Each sensor input contains an integrated RF noise detector. This block will detect injected RF noise on the CS pin. The detector threshold is dependent upon the noise frequency. If RF noise is detected on a CS line, that sample is removed and not compared against the threshold. 4.6 ALERT# Pin The ALERT# pin is an active low (or active high when configured) output that is driven when an interrupt event is detected. Whenever an interrupt is generated, the INT bit (see Section 5.1, "Main Control Register") is set. The ALERT# pin is cleared when the INT bit is cleared by the user. Additionally, when the INT bit is cleared by the user, status bits are only cleared if no touch is detected. 4.6.1 Sensor Interrupt Behavior The sensor interrupts are generated in one of two ways: 1. An interrupt is generated when a touch is detected and, as a user selectable option, when a release is detected (by default - see Section 5.6). See Figure 4.3. 2. If the repeat rate is enabled then, so long as the touch is held, another interrupt will be generated based on the programmed repeat rate (see Figure 4.2). When the repeat rate is enabled, the device uses an additional control called MPRESS that determines whether a touch is flagged as a simple "touch" or a "press and hold". The MPRESS[3:0] bits set a minimum press timer. When the button is touched, the timer begins. If the sensor pad is released before the minimum press timer expires, it is flagged as a touch and an interrupt is generated upon release. If the sensor input detects a touch for longer than this timer value, it is flagged as a "press and hold" event. So long as the touch is held, interrupts will be generated at the programmed repeat rate and upon release (if enabled). APPLICATION NOTE: Figure 4.2 and Figure 4.3 show default operation which is to generate an interrupt upon sensor pad release and an active-low ALERT# pin. APPLICATION NOTE: The host may need to poll the device twice to determine that a release has been detected. Interrupt on Touch Touch Detected Polling Cycle (35ms) Min Press Setting (280ms) Button Repeat Rate (175ms) Button Repeat Rate (175ms) Interrupt on Release (optional) INT bit ALERT# pin (active low) Button Status Write to INT bit Figure 4.2 Sensor Interrupt Behavior - Repeat Rate Enabled SMSC CAP1126 35 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Interrupt on Touch Polling Cycle (35ms) Interrupt on Release (optional) Touch Detected INT bit ALERT# pin (active low) Button Status Write to INT bit Figure 4.3 Sensor Interrupt Behavior - No Repeat Rate Enabled Revision 1.32 (01-05-12) 36 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Chapter 5 Register Description The registers shown in Table 5.1 are accessible through the communications protocol. An entry of `-' indicates that the bit is not used and will always read `0'. Table 5.1 Register Set in Hexadecimal Order REGISTER ADDRESS R/W REGISTER NAME FUNCTION DEFAULT VALUE PAGE 00h R/W Main Control Controls general power states and power dissipation 00h Page 41 02h R General Status Stores general status bits 00h Page 42 03h R Sensor Input Status Returns the state of the sampled capacitive touch sensor inputs 00h Page 42 04h R LED Status Stores status bits for LEDs 00h Page 42 0Ah R Noise Flag Status Stores the noise flags for sensor inputs 00h Page 43 10h R Sensor Input 1 Delta Count Stores the delta count for CS1 00h Page 44 11h R Sensor Input 2 Delta Count Stores the delta count for CS2 00h Page 44 12h R Sensor Input 3 Delta Count Stores the delta count for CS3 00h Page 44 13h R Sensor Input 4 Delta Count Stores the delta count for CS4 00h Page 44 14h R Sensor Input 5 Delta Count Stores the delta count for CS5 00h Page 44 15h R Sensor Input 6 Delta Count Stores the delta count for CS6 00h Page 44 1Fh R/W Sensitivity Control Controls the sensitivity of the threshold and delta counts and data scaling of the base counts 2Fh Page 44 20h R/W Configuration Controls general functionality 20h Page 46 21h R/W Sensor Input Enable Controls whether the capacitive touch sensor inputs are sampled 3Fh Page 48 22h R/W Sensor Input Configuration Controls max duration and autorepeat delay for sensor inputs operating in the full power state A4h Page 48 23h R/W Sensor Input Configuration 2 Controls the MPRESS controls for all sensor inputs 07h Page 50 24h R/W Averaging and Sampling Config Controls averaging and sampling window 39h Page 51 26h R/W Calibration Activate Forces re-calibration for capacitive touch sensor inputs 00h Page 53 SMSC CAP1126 37 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 5.1 Register Set in Hexadecimal Order (continued) REGISTER ADDRESS R/W REGISTER NAME FUNCTION DEFAULT VALUE PAGE 27h R/W Interrupt Enable Enables Interrupts associated with capacitive touch sensor inputs 3Fh Page 53 28h R/W Repeat Rate Enable Enables repeat rate for all sensor inputs 3Fh Page 54 2Ah R/W Multiple Touch Configuration Determines the number of simultaneous touches to flag a multiple touch condition 80h Page 54 2Bh R/W Multiple Touch Pattern Configuration Determines the multiple touch pattern (MTP) configuration 00h Page 55 2Dh R/W Multiple Touch Pattern Determines the pattern or number of sensor inputs used by the MTP circuitry 3Fh Page 56 2Fh R/W Recalibration Configuration Determines re-calibration timing and sampling window 8Ah Page 57 30h R/W Sensor Input 1 Threshold Stores the delta count threshold to determine a touch for Capacitive Touch Sensor Input 1 40h Page 59 31h R/W Sensor Input 2 Threshold Stores the delta count threshold to determine a touch for Capacitive Touch Sensor Input 2 40h Page 59 32h R/W Sensor Input 3 Threshold Stores the delta count threshold to determine a touch for Capacitive Touch Sensor Input 3 40h Page 59 33h R/W Sensor Input 4 Threshold Stores the delta count threshold to determine a touch for Capacitive Touch Sensor Input 4 40h Page 59 34h R/W Sensor Input 5 Threshold Stores the delta count threshold to determine a touch for Capacitive Touch Sensor Input 5 40h Page 59 35h R/W Sensor Input 6 Threshold Stores the delta count threshold to determine a touch for Capacitive Touch Sensor Input 6 40h Page 59 38h R/W Sensor Input Noise Threshold Stores controls for selecting the noise threshold for all sensor inputs 01h Page 59 Standby Configuration Registers 40h R/W Standby Channel Controls which sensor inputs are enabled while in standby 00h Page 60 41h R/W Standby Configuration Controls averaging and cycle time while in standby 39h Page 60 42h R/W Standby Sensitivity Controls sensitivity settings used while in standby 02h Page 62 43h R/W Standby Threshold Stores the touch detection threshold for active sensor inputs in standby 40h Page 63 Revision 1.32 (01-05-12) 38 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 5.1 Register Set in Hexadecimal Order (continued) REGISTER ADDRESS R/W REGISTER NAME FUNCTION 44h R/W Configuration 2 Stores additional configuration controls for the device DEFAULT VALUE PAGE 40h Page 46 Base Count Registers 50h R Sensor Input 1 Base Count Stores the reference count value for sensor input 1 C8h Page 63 51h R Sensor Input 2 Base Count Stores the reference count value for sensor input 2 C8h Page 63 52h R Sensor Input 3 Base Count Stores the reference count value for sensor input 3 C8h Page 63 53h R Sensor Input 4 Base Count Stores the reference count value for sensor input 4 C8h Page 63 54h R Sensor Input 5 Base Count Stores the reference count value for sensor input 5 C8h Page 63 55h R Sensor Input 6 Base Count Stores the reference count value for sensor input 6 C8h Page 63 LED Controls 71h R/W LED Output Type Controls the output type for the LED outputs 00h Page 64 72h R/W Sensor Input LED Linking Controls linking of sensor inputs to LED channels 00h Page 64 73h R/W LED Polarity Controls the output polarity of LEDs 00h Page 65 74h R/W LED Output Control Controls the output state of the LEDs 00h Page 66 77h R/W LED Linked Transition Control Controls the transition when LEDs are linked to CS channels 00h Page 67 79h R/W LED Mirror Control Controls the mirroring of duty cycles for the LEDs 00h Page 68 81h R/W LED Behavior 1 Controls the behavior and response of LEDs 1 - 2 00h Page 68 84h R/W LED Pulse 1 Period Controls the period of each breathe during a pulse 20h Page 70 85h R/W LED Pulse 2 Period Controls the period of the breathing during breathe and pulse operation 14h Page 72 86h R/W LED Breathe Period Controls the period of an LED breathe operation 5Dh Page 73 88h R/W LED Config Controls LED configuration 04h Page 74 90h R/W LED Pulse 1 Duty Cycle Determines the min and max duty cycle for the pulse operation F0h Page 75 91h R/W LED Pulse 2 Duty Cycle Determines the min and max duty cycle for breathe and pulse operation F0h Page 75 SMSC CAP1126 39 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 5.1 Register Set in Hexadecimal Order (continued) REGISTER ADDRESS R/W REGISTER NAME FUNCTION DEFAULT VALUE PAGE 92h R/W LED Breathe Duty Cycle Determines the min and max duty cycle for the breathe operation F0h Page 75 93h R/W LED Direct Duty Cycle Determines the min and max duty cycle for Direct mode LED operation F0h Page 75 94h R/W LED Direct Ramp Rates Determines the rising and falling edge ramp rates of the LEDs 00h Page 76 95h R/W LED Off Delay Determines the off delay for all LED behaviors 00h Page 77 R Sensor Input 1 Calibration Stores the upper 8-bit calibration value for sensor input 1 00h Page 80 R Sensor Input 2 Calibration Stores the upper 8-bit calibration value for sensor input 2 00h Page 80 R Sensor Input 3 Calibration Stores the upper 8-bit calibration value for sensor input 3 00h Page 80 R Sensor Input 4 Calibration Stores the upper 8-bit calibration value for sensor input 4 00h Page 80 R Sensor Input 5 Calibration Stores the upper 8-bit calibration value for sensor input 5 00h Page 80 R Sensor Input 6 Calibration Stores the upper 8-bit calibration value for sensor input 6 00h Page 80 R Sensor Input Calibration LSB 1 Stores the 2 LSBs of the calibration value for sensor inputs 1 - 4 00h Page 80 R Sensor Input Calibration LSB 2 Stores the 2 LSBs of the calibration value for sensor inputs 5 - 6 00h Page 80 FDh R Product ID Stores a fixed value that identifies each product 53h Page 81 FEh R Manufacturer ID Stores a fixed value that identifies SMSC 5Dh Page 81 FFh R Revision Stores a fixed value that represents the revision number 83h Page 81 B1h B2h B3h B4h B5h B6h B9h BAh During Power-On-Reset (POR), the default values are stored in the registers. A POR is initiated when power is first applied to the part and the voltage on the VDD supply surpasses the POR level as specified in the electrical characteristics. Any reads to undefined registers will return 00h. Writes to undefined registers will not have an effect. When a bit is "set", this means that the user writes a logic `1' to it. When a bit is "cleared", this means that the user writes a logic `0' to it. Revision 1.32 (01-05-12) 40 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet 5.1 Main Control Register Table 5.2 Main Control Register ADDR R/W REGISTER 00h R/W Main Control B7 B6 GAIN[1:0] B5 B4 B3 B2 B1 B0 DEFAULT STBY DSLEEP - - - INT 00h The Main Control register controls the primary power state of the device. Bits 7 - 6 - GAIN[1:0] - Controls the gain used by the capacitive touch sensing circuitry. As the gain is increased, the effective sensitivity is likewise increased as a smaller delta capacitance is required to generate the same delta count values. The sensitivity settings may need to be adjusted along with the gain settings such that data overflow does not occur. APPLICATION NOTE: The gain settings apply to both Standby and Active states. Table 5.3 GAIN Bit Decode GAIN[1:0] 1 0 CAPACITIVE TOUCH SENSOR GAIN 0 0 1 0 1 2 1 0 4 1 1 8 Bit 5 - STBY - Enables Standby. `0' (default) - Sensor input scanning is active and LEDs are functional. `1' - Capacitive touch sensor input scanning is limited to the sensor inputs set in the Standby Channel register (see Section 5.20). The status registers will not be cleared until read. LEDs that are linked to capacitive touch sensor inputs will remain linked and active. Sensor inputs that are no longer sampled will flag a release and then remain in a non-touched state. LEDs that are manually controlled will be unaffected. Bit 4 - DSLEEP - Enables Deep Sleep by deactivating all functions. This bit will be cleared when the WAKE pin is driven high. If the CAP1126 is configured to communicate using the BC-Link protocol, this bit is ignored. `0' (default) - Sensor input scanning is active and LEDs are functional. `1' - All sensor input scanning is disabled. All LEDs are driven to their programmed non-actuated state and no PWM operations will be done. The status registers are automatically cleared and the INT bit is cleared. Bit 0 - INT - Indicates that there is an interrupt. When this bit is set, it asserts the ALERT# pin. If a channel detects a touch and its associated interrupt enable bit is not set to a logic `1', no action is taken. This bit is cleared by writing a logic `0' to it. When this bit is cleared, the ALERT# pin will be deasserted and all status registers will be cleared if the condition has been removed. If the WAKE/SPI_MOSI pin is asserted as a result of a touch detected while in Standby, it will likewise be deasserted when this bit is cleared. SMSC CAP1126 41 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Note that the WAKE / SPI_MOSI pin is not driven when communicating via the 4-wire SPI protocol. 5.2 `0' - No interrupt pending. `1' - A touch has been detected on one or more channels and the interrupt has been asserted. Status Registers Table 5.4 Status Registers ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 02h R General Status - - - LED RESET MULT MTP TOUCH 00h 03h R Sensor Input Status - - CS6 CS5 CS4 CS3 CS2 CS1 00h 04h R LED Status - - - - - - LED2_ DN LED1_ DN 00h All status bits are cleared when the device enters the Deep Sleep (DSLEEP = `1' - see Section 5.1). 5.2.1 General Status - 02h Bit 4 - LED - Indicates that one or more LEDs have finished their programmed activity. This bit is set if any bit in the LED Status register is set. Bit 3 - RESET - Indicates that the device has come out of reset. This bit is set when the device exits a POR state or when the RESET pin has been deasserted and qualified via the RESET pin filter (see Section 4.2). This bit will cause the INT bit to be set and is cleared when the INT bit is cleared. Bit 2 - MULT - Indicates that the device is blocking detected touches due to the Multiple Touch detection circuitry (see Section 5.14). This bit will not cause the INT bit to be set and hence will not cause an interrupt. Bit 1 - MTP - Indicates that the device has detected a number of sensor inputs that exceed the MTP threshold either via the pattern recognition or via the number of sensor inputs (see Section 5.15). This bit will cause the INT bit to be set if the MTP_ALERT bit is also set. This bit will not be cleared until the condition that caused it to be set has been removed. Bit 0 - TOUCH - Indicates that a touch was detected. This bit is set if any bit in the Sensor Input Status register is set. 5.2.2 Sensor Input Status - 03h The Sensor Input Status Register stores status bits that indicate a touch has been detected. A value of `0' in any bit indicates that no touch has been detected. A value of `1' in any bit indicates that a touch has been detected. All bits are cleared when the INT bit is cleared and if a touch on the respective capacitive touch sensor input is no longer present. If a touch is still detected, the bits will not be cleared (but this will not cause the interrupt to be asserted - see Section 5.6). Bit 5 - CS6 - Indicates that a touch was detected on Sensor Input 6. Bit 4 - CS5 - Indicates that a touch was detected on Sensor Input 5. Bit 3 - CS4 - Indicates that a touch was detected on Sensor Input 4. Bit 2 - CS3 - Indicates that a touch was detected on Sensor Input 3. Revision 1.32 (01-05-12) 42 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Bit 1 - CS2 - Indicates that a touch was detected on Sensor Input 2. This sensor input can be linked to LED2. Bit 0 - CS1 - Indicates that a touch was detected on Sensor Input 1. This sensor input can be linked to LED1. 5.2.3 LED Status - 04h The LED Status Registers indicate when an LED has completed its configured behavior (see Section 5.31, "LED Behavior Register") after being actuated by the host (see Section 5.28, "LED Output Control Register"). These bits are ignored when the LED is linked to a capacitive sensor input. All LED Status bits are cleared when the INT bit is cleared. Bit 1 - LED2_DN - Indicates that LED2 has finished its behavior after being actuated by the host. Bit 0 - LED1_DN - Indicates that LED1 has finished its behavior after being actuated by the host. 5.3 Noise Flag Status Registers Table 5.5 Noise Flag Status Registers ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 0Ah R Noise Flag Status - - CS6_ NOISE CS5_ NOISE CS4_ NOISE CS3_ NOISE CS2_ NOISE CS1_ NOISE 00h The Noise Flag Status registers store status bits that are generated from the analog block if the detected noise is above the operating region of the analog detector or the RF noise detector. These bits indicate that the most recently received data from the sensor input is invalid and should not be used for touch detection. So long as the bit is set for a particular channel, the delta count value is reset to 00h and thus no touch is detected. These bits are not sticky and will be cleared automatically if the analog block does not report a noise error. APPLICATION NOTE: If the MTP detection circuitry is enabled, these bits count as sensor inputs above the MTP threshold (see Section 4.5.4, "Multiple Touch Pattern Detection") even if the corresponding delta count is not. If the corresponding delta count also exceeds the MTP threshold, it is not counted twice. APPLICATION NOTE: Regardless of the state of the Noise Status bits, if low frequency noise is detected on a sensor input, that sample will be discarded unless the DIS_ANA_NOISE bit is set. As well, if RF noise is detected on a sensor input, that sample will be discarded unless the DIS_RF_NOISE bit is set. SMSC CAP1126 43 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet 5.4 Sensor Input Delta Count Registers Table 5.6 Sensor Input Delta Count Registers ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 10h R Sensor Input 1 Delta Count Sign 64 32 16 8 4 2 1 00h 11h R Sensor Input 2 Delta Count Sign 64 32 16 8 4 2 1 00h 12h R Sensor Input 3 Delta Count Sign 64 32 16 8 4 2 1 00h 13h R Sensor Input 4 Delta Count Sign 64 32 16 8 4 2 1 00h 14h R Sensor Input 5 Delta Count Sign 64 32 16 8 4 2 1 00h 15h R Sensor Input 6 Delta Count Sign 64 32 16 8 4 2 1 00h The Sensor Input Delta Count registers store the delta count that is compared against the threshold used to determine if a touch has been detected. The count value represents a change in input due to the capacitance associated with a touch on one of the sensor inputs and is referenced to a calibrated base "Not Touched" count value. The delta is an instantaneous change and is updated once per sensor input per sensing cycle (see Section 4.5.1, "Sensing Cycle"). The value presented is a standard 2's complement number. In addition, the value is capped at a value of 7Fh. A reading of 7Fh indicates that the sensitivity settings are too high and should be adjusted accordingly (see Section 5.5). The value is also capped at a negative value of 80h for negative delta counts which may result upon a release. 5.5 Sensitivity Control Register Table 5.7 Sensitivity Control Register ADDR R/W REGISTER B7 1Fh R/W Sensitivity Control - B6 B5 B4 DELTA_SENSE[2:0] B3 B2 B1 B0 DEFAULT BASE_SHIFT[3:0] The Sensitivity Control register controls the sensitivity of a touch detection. Bits 6-4 DELTA_SENSE[2:0] - Controls the sensitivity of a touch detection. The sensitivity settings act to scale the relative delta count value higher or lower based on the system parameters. A setting of 000b is the most sensitive while a setting of 111b is the least sensitive. At the more sensitive settings, touches are detected for a smaller delta capacitance corresponding to a "lighter" touch. These settings are more sensitive to noise, however, and a noisy environment may flag more false touches with higher sensitivity levels. APPLICATION NOTE: A value of 128x is the most sensitive setting available. At the most sensitivity settings, the MSB of the Delta Count register represents 64 out of ~25,000 which corresponds to a touch of approximately 0.25% of the base capacitance (or a C of 25fF from a 10pF base Revision 1.32 (01-05-12) 44 DATASHEET SMSC CAP1126 2Fh 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet capacitance). Conversely, a value of 1x is the least sensitive setting available. At these settings, the MSB of the Delta Count register corresponds to a delta count of 8192 counts out of ~25,000 which corresponds to a touch of approximately 33% of the base capacitance (or a C of 3.33pF from a 10pF base capacitance). Table 5.8 DELTA_SENSE Bit Decode DELTA_SENSE[2:0] 2 1 0 SENSITIVITY MULTIPLIER 0 0 0 128x (most sensitive) 0 0 1 64x 0 1 0 32x (default) 0 1 1 16x 1 0 0 8x 1 0 1 4x 1 1 0 2x 1 1 1 1x - (least sensitive) Bits 3 - 0 - BASE_SHIFT[3:0] - Controls the scaling and data presentation of the Base Count registers. The higher the value of these bits, the larger the range and the lower the resolution of the data presented. The scale factor represents the multiplier to the bit-weighting presented in these register descriptions. APPLICATION NOTE: The BASE_SHIFT[3:0] bits normally do not need to be updated. These settings will not affect touch detection or sensitivity. These bits are sometimes helpful in analyzing the Cap Sensing board performance and stability. Table 5.9 BASE_SHIFT Bit Decode BASE_SHIFT[3:0] 3 2 1 0 DATA SCALING FACTOR 0 0 0 0 1x 0 0 0 1 2x 0 0 1 0 4x 0 0 1 1 8x 0 1 0 0 16x 0 1 0 1 32x 0 1 1 0 64x 0 1 1 1 128x SMSC CAP1126 45 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 5.9 BASE_SHIFT Bit Decode (continued) BASE_SHIFT[3:0] 3 2 1 0 DATA SCALING FACTOR 1 0 0 0 256x 256x (default = 1111b) All others 5.6 Configuration Registers Table 5.10 Configuration Registers ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 20h R/W Configuration TIMEOUT WAKE_ CFG DIS_ DIG_ NOISE DIS_ ANA_ NOISE MAX_ DUR_EN - - - A0h (rev B) 20h (rev C) 44h R/W Configuration 2 INV_LINK_ TRAN ALT_ POL BLK_PWR_ CTRL BLK_POL_ MIR SHOW_ RF_ NOISE DIS_ RF_ NOISE - INT_ REL_n 40h The Configuration registers control general global functionality that affects the entire device. 5.6.1 Configuration - 20h Bit 7 - TIMEOUT - Enables the timeout and idle functionality of the SMBus protocol. `0' (default for Functional Revision C) - The SMBus timeout and idle functionality are disabled. The SMBus interface will not time out if the clock line is held low. Likewise, it will not reset if both the data and clock lines are held high for longer than 200us. This is used for I2C compliance. `1' (default for Functional Revision B) - The SMBus timeout and idle functionality are enabled. The SMBus interface will time out if the clock line is held low for longer than 30ms. Likewise, it will reset if both the data and clock lines are held high for longer than 200us. Bit 6 - WAKE_CFG - Configures the operation of the WAKE pin. `0' (default) - The WAKE pin is not asserted when a touch is detected while the device is in Standby. It will still be used to wake the device from Deep Sleep when driven high. `1' - The WAKE pin will be asserted high when a touch is detected while the device is in Standby. It will also be used to wake the device from Deep Sleep when driven high. Bit 5 - DIS_DIG_NOISE - Determines whether the digital noise threshold (see Section 5.19, "Sensor Input Noise Threshold Register") is used by the device. Setting this bit disables the feature. `0' - The digital noise threshold is used. If a delta count value exceeds the noise threshold but does not exceed the touch threshold, the sample is discarded and not used for the automatic recalibration routine. `1' (default) - The noise threshold is disabled. Any delta count that is less than the touch threshold is used for the automatic re-calibration routine. Revision 1.32 (01-05-12) 46 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Bit 4 - DIS_ANA_NOISE - Determines whether the analog noise filter is enabled. Setting this bit disables the feature. `0' (default) - If low frequency noise is detected by the analog block, the delta count on the corresponding channel is set to 0. Note that this does not require that Noise Status bits be set. `1' - A touch is not blocked even if low frequency noise is detected. Bit 3 - MAX_DUR_EN - Determines whether the maximum duration recalibration is enabled. 5.6.2 `0' (default) - The maximum duration recalibration functionality is disabled. A touch may be held indefinitely and no re-calibration will be performed on any sensor input. `1' - The maximum duration recalibration functionality is enabled. If a touch is held for longer than the MAX_DUR bit settings, then the re-calibration routine will be restarted (see Section 5.8). Configuration 2 - 44h Bit 7 - INV_LINK_TRAN - Determines the behavior of the Linked LED Transition controls (see Section 5.29). `0' (default) - The Linked LED Transition controls set the min duty cycle equal to the max duty cycle. `1' - The Linked LED Transition controls will invert the touch signal. For example, a touch signal will be inverted to a non-touched signal. Bit 6 - ALT_POL - Determines the ALERT# pin polarity and behavior. `0' - The ALERT# pin is active high and push-pull. `1' (default) - The ALERT# pin is active low and open drain. Bit 5 - BLK_PWR_CTRL - Determines whether the device will reduce power consumption while waiting between conversion time completion and the end of the polling cycle. `0' (default) - The device will always power down as much as possible during the time between the end of the last conversion and the end of the polling cycle. `1' - The device will not power down the Cap Sensor during the time between the end of the last conversion and the end of the polling cycle. Bit 4 - BLK_POL_MIR - Determines whether the LED Mirror Control register bits are linked to the LED Polarity bits. Setting this bit blocks the normal behavior which is to automatically set and clear the LED Mirror Control bits when the LED Polarity bits are set or cleared. `0' (default) - When the LED Polarity controls are set, the corresponding LED Mirror control is automatically set. Likewise, when the LED Polarity controls are cleared, the corresponding LED Mirror control is also cleared. `1' - When the LED Polarity controls are set, the corresponding LED Mirror control is not automatically set. Bit 3 - SHOW_RF_NOISE - Determines whether the Noise Status bits will show RF Noise as the only input source. `0' (default) - The Noise Status registers will show both RF noise and low frequency EMI noise if either is detected on a capacitive touch sensor input. `1' - The Noise Status registers will only show RF noise if it is detected on a capacitive touch sensor input. EMI noise will still be detected and touches will be blocked normally; however, the status bits will not be updated. Bit 2 - DIS_RF_NOISE - Determines whether the RF noise filter is enabled. Setting this bit disables the feature. `0' (default) - If RF noise is detected by the analog block, the delta count on the corresponding channel is set to 0. Note that this does not require that Noise Status bits be set. `1' - A touch is not blocked even if RF noise is detected. SMSC CAP1126 47 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Bit 0 - INT_REL_n - Controls the interrupt behavior when a release is detected on a button. 5.7 `0' (default) - An interrupt is generated when a press is detected and again when a release is detected and at the repeat rate (if enabled - see Section 5.13). `1' - An interrupt is generated when a press is detected and at the repeat rate but not when a release is detected. Sensor Input Enable Registers Table 5.11 Sensor Input Enable Registers ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 21h R/W Sensor Input Enable - - CS6_EN CS5_EN CS4_EN CS3_EN CS2_EN CS1_EN 3Fh The Sensor Input Enable registers determine whether a capacitive touch sensor input is included in the sampling cycle. The length of the sampling cycle is not affected by the number of sensor inputs measured. Bit 5 - CS6_EN - Enables the CS6 input to be included during the sampling cycle. `0' - The CS6 input is not included in the sampling cycle. `1' (default) - The CS6 input is included in the sampling cycle. Bit 4 - CS5_EN - Enables the CS5 input to be included during the sampling cycle. Bit 3 - CS4_EN - Enables the CS4 input to be included during the sampling cycle. Bit 2 - CS3_EN - Enables the CS3 input to be included during the sampling cycle. Bit 1 - CS2_EN - Enables the CS2 input to be included during the sampling cycle. Bit 0 - CS1_EN - Enables the CS1 input to be included during the sampling cycle. 5.8 Sensor Input Configuration Register Table 5.12 Sensor Input Configuration Register ADDR R/W REGISTER 22h R/W Sensor Input Configuration B7 B6 B5 B4 MAX_DUR[3:0] B3 B2 B1 RPT_RATE[3:0] B0 DEFAULT A4h The Sensor Input Configuration Register controls timings associated with the Capacitive sensor inputs 1 - 6. Bits 7 - 4 - MAX_DUR[3:0] - (default 1010b) - Determines the maximum time that a sensor pad is allowed to be touched until the capacitive touch sensor input is recalibrated, as shown in Table 5.13. Revision 1.32 (01-05-12) 48 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 5.13 MAX_DUR Bit Decode MAX_DUR[3:0] 3 2 1 0 TIME BEFORE RECALIBRATION 0 0 0 0 560ms 0 0 0 1 840ms 0 0 1 0 1120ms 0 0 1 1 1400ms 0 1 0 0 1680ms 0 1 0 1 2240ms 0 1 1 0 2800ms 1 1 1 3360ms 1 0 0 0 3920ms 1 0 0 1 4480ms 1 0 1 0 5600ms (default) 1 0 1 1 6720ms 1 1 0 0 7840ms 1 1 0 1 8906ms 1 1 1 0 10080ms 1 1 1 1 11200ms Bits 3 - 0 - RPT_RATE[3:0] - (default 0100b) Determines the time duration between interrupt assertions when auto repeat is enabled. The resolution is 35ms the range is from 35ms to 560ms as shown in Table 5.14. Table 5.14 RPT_RATE Bit Decode RPT_RATE[3:0] 3 2 1 0 INTERRUPT REPEAT RATE 0 0 0 0 35ms 0 0 0 1 70ms 0 0 1 0 105ms 0 0 1 1 140ms 0 1 0 0 175ms (default) 0 1 0 1 210ms 0 1 1 0 245ms SMSC CAP1126 49 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 5.14 RPT_RATE Bit Decode (continued) RPT_RATE[3:0] 3 2 1 0 INTERRUPT REPEAT RATE 0 1 1 1 280ms 1 0 0 0 315ms 1 0 0 1 350ms 1 0 1 0 385ms 1 0 1 1 420ms 1 1 0 0 455ms 1 1 0 1 490ms 1 1 1 0 525ms 1 1 1 1 560ms 5.9 Sensor Input Configuration 2 Register Table 5.15 Sensor Input Configuration 2 Register ADDR R/W REGISTER B7 B6 B5 B4 23h R/W Sensor Input Configuration 2 - - - - B3 B2 B1 B0 M_PRESS[3:0] DEFAULT 07h Bits 3 - 0 - M_PRESS[3:0] - (default 0111b) - Determines the minimum amount of time that sensor inputs configured to use auto repeat must detect a sensor pad touch to detect a "press and hold" event. If the sensor input detects a touch for longer than the M_PRESS[3:0] settings, a "press and hold" event is detected. If a sensor input detects a touch for less than or equal to the M_PRESS[3:0] settings, a touch event is detected. The resolution is 35ms the range is from 35ms to 560ms as shown in Table 5.16. Table 5.16 M_PRESS Bit Decode M_PRESS[3:0] 3 2 1 0 M_PRESS SETTINGS 0 0 0 0 35ms 0 0 0 1 70ms 0 0 1 0 105ms 0 0 1 1 140ms 0 1 0 0 175ms 0 1 0 1 210ms Revision 1.32 (01-05-12) 50 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 5.16 M_PRESS Bit Decode (continued) M_PRESS[3:0] 3 2 1 0 M_PRESS SETTINGS 0 1 1 0 245ms 0 1 1 1 280ms (default) 1 0 0 0 315ms 1 0 0 1 350ms 1 0 1 0 385ms 1 0 1 1 420ms 1 1 0 0 455ms 1 1 0 1 490ms 1 1 1 0 525ms 1 1 1 1 560ms 5.10 Averaging and Sampling Configuration Register Table 5.17 Averaging and Sampling Configuration Register ADDR R/W REGISTER 24h R/W Averaging and Sampling Config B7 B6 B5 B4 AVG[2:0] B3 B2 SAMP_TIME[1:0] B1 B0 DEFAULT CYCLE_TIME [1:0] 39h The Averaging and Sampling Configuration register controls the number of samples taken and the total sensor input cycle time for all active sensor inputs while the device is functioning in Active state. Bits 6 - 4 - AVG[2:0] - Determines the number of samples that are taken for all active channels during the sensor cycle as shown in Table 5.18. All samples are taken consecutively on the same channel before the next channel is sampled and the result is averaged over the number of samples measured before updating the measured results. For example, if CS1, CS2, and CS3 are sampled during the sensor cycle, and the AVG[2:0] bits are set to take 4 samples per channel, then the full sensor cycle will be: CS1, CS1, CS1, CS1, CS2, CS2, CS2, CS2, CS3, CS3, CS3, CS3. Table 5.18 AVG Bit Decode AVG[2:0] 2 1 0 NUMBER OF SAMPLES TAKEN PER MEASUREMENT 0 0 0 1 0 0 1 2 SMSC CAP1126 51 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 5.18 AVG Bit Decode (continued) AVG[2:0] 2 1 0 NUMBER OF SAMPLES TAKEN PER MEASUREMENT 0 1 0 4 0 1 1 8 (default) 1 0 0 16 1 0 1 32 1 1 0 64 1 1 1 128 Bits 3 - 2 - SAMP_TIME[1:0] - Determines the time to take a single sample as shown in Table 5.19. Table 5.19 SAMP_TIME Bit Decode SAMP_TIME[1:0] 1 0 SAMPLE TIME 0 0 320us 0 1 640us 1 0 1.28ms (default) 1 1 2.56ms Bits 1 - 0 - CYCLE_TIME[1:0] - Determines the overall cycle time for all measured channels during normal operation as shown in Table 5.20. All measured channels are sampled at the beginning of the cycle time. If additional time is remaining, then the device is placed into a lower power state for the remaining duration of the cycle. Table 5.20 CYCLE_TIME Bit Decode CYCLE_TIME[1:0] 1 0 OVERALL CYCLE TIME 0 0 35ms 0 1 70ms (default) 1 0 105ms 1 1 140ms APPLICATION NOTE: The programmed cycle time is only maintained if the total averaging time for all samples is less than the programmed cycle. The AVG[2:0] bits will take priority so that if more samples are required than would normally be allowed during the cycle time, the cycle time will be extended as necessary to accommodate the number of samples to be measured. Revision 1.32 (01-05-12) 52 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet 5.11 Calibration Activate Register Table 5.21 Calibration Activate Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 26h R/W Calibration Activate - - CS6_ CAL CS5_ CAL CS4_ CAL CS3_ CAL CS2_ CAL CS1_ CAL 00h The Calibration Activate register forces the respective sensor inputs to be re-calibrated affecting both the analog and digital blocks. During the re-calibration routine, the sensor inputs will not detect a press for up to 600ms and the Sensor Input Base Count register values will be invalid. During this time, any press on the corresponding sensor pads will invalidate the re-calibration. When finished, the CALX[9:0] bits will be updated (see Section 5.39). When the corresponding bit is set, the device will perform the calibration and the bit will be automatically cleared once the re-calibration routine has finished. Bit 5 - CS6_CAL - When set, the CS6 input is re-calibrated. This bit is automatically cleared once the sensor input has been re-calibrated successfully. Bit 4 - CS5_CAL - When set, the CS5 input is re-calibrated. This bit is automatically cleared once the sensor input has been re-calibrated successfully. Bit 3 - CS4_CAL - When set, the CS4 input is re-calibrated. This bit is automatically cleared once the sensor input has been re-calibrated successfully. Bit 2 - CS3_CAL - When set, the CS3 input is re-calibrated. This bit is automatically cleared once the sensor input has been re-calibrated successfully. Bit 1 - CS2_CAL - When set, the CS2 input is re-calibrated. This bit is automatically cleared once the sensor input has been re-calibrated successfully. Bit 0 - CS1_CAL - When set, the CS1 input is re-calibrated. This bit is automatically cleared once the sensor input has been re-calibrated successfully. 5.12 Interrupt Enable Register Table 5.22 Interrupt Enable Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 27h R/W Interrupt Enable - - CS6_ INT_EN CS5_ INT_EN CS4_ INT_EN CS3_ INT_EN CS2_ INT_EN CS1_ INT_EN 3Fh The Interrupt Enable register determines whether a sensor pad touch or release (if enabled) causes the interrupt pin to be asserted. Bit 5 - CS6_INT_EN - Enables the interrupt pin to be asserted if a touch is detected on CS6 (associated with the CS6 status bit). `0' - The interrupt pin will not be asserted if a touch is detected on CS6 (associated with the CS6 status bit). `1' (default) - The interrupt pin will be asserted if a touch is detected on CS6 (associated with the CS6 status bit). SMSC CAP1126 53 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Bit 4 - CS5_INT_EN - Enables the interrupt pin to be asserted if a touch is detected on CS5 (associated with the CS5 status bit). Bit 3 - CS4_INT_EN - Enables the interrupt pin to be asserted if a touch is detected on CS4 (associated with the CS4 status bit). Bit 2 - CS3_INT_EN - Enables the interrupt pin to be asserted if a touch is detected on CS3 (associated with the CS3 status bit). Bit 1 - CS2_INT_EN - Enables the interrupt pin to be asserted if a touch is detected on CS2 (associated with the CS2 status bit). Bit 0 - CS1_INT_EN - Enables the interrupt pin to be asserted if a touch is detected on CS1 (associated with the CS1 status bit). 5.13 Repeat Rate Enable Register Table 5.23 Repeat Rate Enable Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 28h R/W Repeat Rate Enable - - CS6_ RPT_EN CS5_ RPT_EN CS4_ RPT_EN CS3_ RPT_EN CS2_ RPT_EN CS1_ RPT_EN 3Fh The Repeat Rate Enable register enables the repeat rate of the sensor inputs as described in Section 4.6.1. Bit 5 - CS6_RPT_EN - Enables the repeat rate for capacitive touch sensor input 6. `0' - The repeat rate for CS6 is disabled. It will only generate an interrupt when a touch is detected and when a release is detected no matter how long the touch is held for. `1' (default) - The repeat rate for CS6 is enabled. In the case of a "touch" event, it will generate an interrupt when a touch is detected and a release is detected (as determined by the INT_REL_n bit - see Section 5.6). In the case of a "press and hold" event, it will generate an interrupt when a touch is detected and at the repeat rate so long as the touch is held. Bit 4 - CS5_RPT_EN - Enables the repeat rate for capacitive touch sensor input 5. Bit 3 - CS4_RPT_EN - Enables the repeat rate for capacitive touch sensor input 4. Bit 2 - CS3_RPT_EN - Enables the repeat rate for capacitive touch sensor input 3. Bit 1 - CS2_RPT_EN - Enables the repeat rate for capacitive touch sensor input 2. Bit 0 - CS1_RPT_EN - Enables the repeat rate for capacitive touch sensor input 1. 5.14 Multiple Touch Configuration Register Table 5.24 Multiple Touch Configuration ADDR R/W REGISTER B7 B6 B5 B4 2Ah R/W Multiple Touch Config MULT_ BLK_ EN - - - Revision 1.32 (01-05-12) 54 DATASHEET B3 B2 B_MULT_T[1:0] B1 B0 DEFAULT - - 80h SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet The Multiple Touch Configuration register controls the settings for the multiple touch detection circuitry. These settings determine the number of simultaneous buttons that may be pressed before additional buttons are blocked and the MULT status bit is set. Bit 7 - MULT_BLK_EN - Enables the multiple button blocking circuitry. `0' - The multiple touch circuitry is disabled. The device will not block multiple touches. `1' (default) - The multiple touch circuitry is enabled. The device will flag the number of touches equal to programmed multiple touch threshold and block all others. It will remember which sensor inputs are valid and block all others until that sensor pad has been released. Once a sensor pad has been released, the N detected touches (determined via the cycle order of CS1 - CS6) will be flagged and all others blocked. Bits 3 - 2 - B_MULT_T[1:0] - Determines the number of simultaneous touches on all sensor pads before a Multiple Touch Event is detected and sensor inputs are blocked. The bit decode is given by Table 5.25. Table 5.25 B_MULT_T Bit Decode B_MULT_T[1:0] 5.15 1 0 NUMBER OF SIMULTANEOUS TOUCHES 0 0 1 (default) 0 1 2 1 0 3 1 1 4 Multiple Touch Pattern Configuration Register Table 5.26 Multiple Touch Pattern Configuration ADDR R/W REGISTER B7 B6 B5 2Bh R/W Multiple Touch Pattern Config MTP_ EN - - B4 B3 B2 MTP_TH[1:0] B1 B0 DEFAULT COMP_ PTRN MTP_ ALERT 00h The Multiple Touch Pattern Configuration register controls the settings for the multiple touch pattern detection circuitry. This circuitry works like the multiple touch detection circuitry with the following differences: 1. The detection threshold is a percentage of the touch detection threshold as defined by the MTP_TH[1:0] bits whereas the multiple touch circuitry uses the touch detection threshold. 2. The MTP detection circuitry either will detect a specific pattern of sensor inputs as determined by the Multiple Touch Pattern register settings or it will use the Multiple Touch Pattern register settings to determine a minimum number of sensor inputs that will cause the MTP circuitry to flag an event. When using pattern recognition mode, if all of the sensor inputs set by the Multiple Touch Pattern register have a delta count greater than the MTP threshold or have their corresponding Noise Flag Status bits set, the MTP bit will be set. When using the absolute number mode, if the number of sensor inputs with thresholds above the MTP threshold or with Noise Flag Status bits set is equal to or greater than this number, the MTP bit will be set. 3. When an MTP event occurs, all touches are blocked and an interrupt is generated. SMSC CAP1126 55 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet 4. All sensor inputs will remain blocked so long as the requisite number of sensor inputs are above the MTP threshold or have Noise Flag Status bits set. Once this condition is removed, touch detection will be restored. Note that the MTP status bit is only cleared by writing a `0' to the INT bit once the condition has been removed. Bit 7 - MTP_EN - Enables the multiple touch pattern detection circuitry. `0' (default) - The MTP detection circuitry is disabled. `1' - The MTP detection circuitry is enabled. Bits 3-2 - MTP_TH[1:0] - Determine the MTP threshold, as shown in Table 5.27. This threshold is a percentage of sensor input threshold (see Section 5.18, "Sensor Input Threshold Registers") when the device is in the Fully Active state or of the standby threshold (see Section 5.23, "Standby Threshold Register") when the device is in the Standby state. Table 5.27 MTP_TH Bit Decode MTP_TH[1:0] 1 0 THRESHOLD DIVIDE SETTING 0 0 12.5% (default) 0 1 25% 1 0 37.5% 1 1 100% Bit 1 - COMP_PTRN - Determines whether the MTP detection circuitry will use the Multiple Touch Pattern register as a specific pattern of sensor inputs or as an absolute number of sensor inputs. `0' (default) - The MTP detection circuitry will use the Multiple Touch Pattern register bit settings as an absolute minimum number of sensor inputs that must be above the threshold or have Noise Flag Status bits set. The number will be equal to the number of bits set in the register. `1' - The MTP detection circuitry will use pattern recognition. Each bit set in the Multiple Touch Pattern register indicates a specific sensor input that must have a delta count greater than the MTP threshold or have a Noise Flag Status bit set. If the criteria are met, the MTP status bit will be set. Bit 0 - MTP_ALERT - Enables an interrupt if an MTP event occurs. In either condition, the MTP status bit will be set. 5.16 `0' (default) - If an MTP event occurs, the ALERT# pin is not asserted. `1' - If an MTP event occurs, the ALERT# pin will be asserted. Multiple Touch Pattern Register Table 5.28 Multiple Touch Pattern Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 2Dh R/W Multiple Touch Pattern - - CS6_ PTRN CS5_ PTRN CS4_ PTRN CS3_ PTRN CS2_ PTRN CS1_ PTRN 3Fh The Multiple Touch Pattern register acts as a pattern to identify an expected sensor input profile for diagnostics or other significant events. There are two methods for how the Multiple Touch Pattern Revision 1.32 (01-05-12) 56 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet register is used: as specific sensor inputs or number of sensor input that must exceed the MTP threshold or have Noise Flag Status bits set. Which method is used is based on the COMP_PTRN bit (see Section 5.15). The methods are described below. 1. Specific Sensor Inputs: If, during a single polling cycle, the specific sensor inputs above the MTP threshold or with Noise Flag Status bits set match those bits set in the Multiple Touch Pattern register, an MTP event is flagged. 2. Number of Sensor Inputs: If, during a single polling cycle, the number of sensor inputs with a delta count above the MTP threshold or with Noise Flag Status bits set is equal to or greater than the number of pattern bits set, an MTP event is flagged. Bit 5 - CS6_PTRN - Determines whether CS6 is considered as part of the Multiple Touch Pattern. `0' - CS6 is not considered a part of the pattern. `1' - CS6 is considered a part of the pattern or the absolute number of sensor inputs that must have a delta count greater than the MTP threshold or have the Noise Flag Status bit set is increased by 1. Bit 4 - CS5_PTRN - Determines whether CS5 is considered as part of the Multiple Touch Pattern. Bit 3 - CS4_PTRN - Determines whether CS4 is considered as part of the Multiple Touch Pattern. Bit 2 - CS3_PTRN - Determines whether CS3 is considered as part of the Multiple Touch Pattern. Bit 1 - CS2_PTRN - Determines whether CS2 is considered as part of the Multiple Touch Pattern. Bit 0 - CS1_PTRN - Determines whether CS1 is considered as part of the Multiple Touch Pattern. 5.17 Recalibration Configuration Register Table 5.29 Recalibration Configuration Registers ADDR R/W REGISTER B7 B6 B5 2Fh R/W Recalibration Configuration BUT_ LD_TH NO_ CLR_ INTD NO_ CLR_ NEG B4 B3 B2 NEG_DELTA_ CNT[1:0] B1 B0 CAL_CFG[2:0] DEFAULT 8Ah The Recalibration Configuration register controls the automatic re-calibration routine settings as well as advanced controls to program the Sensor Input Threshold register settings. Bit 7 - BUT_LD_TH - Enables setting all Sensor Input Threshold registers by writing to the Sensor Input 1 Threshold register. `0' - Each Sensor Input X Threshold register is updated individually. `1' (default) - Writing the Sensor Input 1 Threshold register will automatically overwrite the Sensor Input Threshold registers for all sensor inputs (Sensor Input Threshold 1 through Sensor Input Threshold 6). The individual Sensor Input X Threshold registers (Sensor Input 2 Threshold through Sensor Input 6 Threshold) can be individually updated at any time. Bit 6 - NO_CLR_INTD - Controls whether the accumulation of intermediate data is cleared if the noise status bit is set. `0' (default) - The accumulation of intermediate data is cleared if the noise status bit is set. `1' - The accumulation of intermediate data is not cleared if the noise status bit is set. APPLICATION NOTE: Bits 5 and 6 should both be set to the same value. Either both should be set to `0' or both should be set to `1'. SMSC CAP1126 57 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Bit 5 - NO_CLR_NEG - Controls whether the consecutive negative delta counts counter is cleared if the noise status bit is set. `0' (default) - The consecutive negative delta counts counter is cleared if the noise status bit is set. `1' - The consecutive negative delta counts counter is not cleared if the noise status bit is set. Bits 4 - 3 - NEG_DELTA_CNT[1:0] - Determines the number of negative delta counts necessary to trigger a digital re-calibration as shown in Table 5.30. Table 5.30 NEG_DELTA_CNT Bit Decode NEG_DELTA_CNT[1:0] 1 0 NUMBER OF CONSECUTIVE NEGATIVE DELTA COUNT VALUES 0 0 8 0 1 16 (default) 1 0 32 1 1 None (disabled) Bits 2 - 0 - CAL_CFG[2:0] - Determines the update time and number of samples of the automatic recalibration routine. The settings apply to all sensor inputs universally (though individual sensor inputs can be configured to support re-calibration - see Section 5.11). Table 5.31 CAL_CFG Bit Decode CAL_CFG[2:0] 2 1 0 RECALIBRATION SAMPLES (SEE Note 5.1) 0 0 0 16 16 0 0 1 32 32 0 1 0 64 64 (default) 0 1 1 128 128 1 0 0 256 256 1 0 1 256 1024 1 1 0 256 2048 1 1 1 256 4096 UPDATE TIME (SEE Note 5.2) Note 5.1 Recalibration Samples refers to the number of samples that are measured and averaged before the Base Count is updated however does not control the base count update period. Note 5.2 Update Time refers to the amount of time (in polling cycle periods) that elapses before the Base Count is updated. The time will depend upon the number of channels active, the averaging setting, and the programmed cycle time. Revision 1.32 (01-05-12) 58 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet 5.18 Sensor Input Threshold Registers Table 5.32 Sensor Input Threshold Registers ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 30h R/W Sensor Input 1 Threshold - 64 32 16 8 4 2 1 40h 31h R/W Sensor Input 2 Threshold - 64 32 16 8 4 2 1 40h 32h R/W Sensor Input 3 Threshold - 64 32 16 8 4 2 1 40h 33h R/W Sensor Input 4 Threshold - 64 32 16 8 4 2 1 40h 34h R/W Sensor Input 5 Threshold - 64 32 16 8 4 2 1 40h 35h R/W Sensor Input 6 Threshold - 64 32 16 8 4 2 1 40h The Sensor Input Threshold registers store the delta threshold that is used to determine if a touch has been detected. When a touch occurs, the input signal of the corresponding sensor pad changes due to the capacitance associated with a touch. If the sensor input change exceeds the threshold settings, a touch is detected. When the BUT_LD_TH bit is set (see Section 5.17 - bit 7), writing data to the Sensor Input 1 Threshold register will update all of the sensor input threshold registers (31h - 35h inclusive). 5.19 Sensor Input Noise Threshold Register Table 5.33 Sensor Input Noise Threshold Register ADDR R/W REGISTER 38h R/W Sensor Input Noise Threshold B7 B6 B5 B4 B3 B2 B1 B0 CS_BN_TH [1:0] DEFAULT 01h The Sensor Input Noise Threshold register controls the value of a secondary internal threshold to detect noise and improve the automatic recalibration routine. If a capacitive touch sensor input exceeds the Sensor Input Noise Threshold but does not exceed the sensor input threshold, it is determined to be caused by a noise spike. That sample is not used by the automatic re-calibration routine. This feature can be disabled by setting the DIS_DIG_NOISE bit. Bits 1-0 - CS1_BN_TH[1:0] - Controls the noise threshold for all capacitive touch sensor inputs, as shown in Table 5.34. The threshold is proportional to the threshold setting. SMSC CAP1126 59 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 5.34 CSx_BN_TH Bit Decode CS_BN_TH[1:0] 5.20 1 0 PERCENT THRESHOLD SETTING 0 0 25% 0 1 37.5% (default) 1 0 50% 1 1 62.5% Standby Channel Register Table 5.35 Standby Channel Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 40h R/W Standby Channel - - CS6_ STBY CS5_ STBY CS4_ STBY CS3_ STBY CS2_ STBY CS1_ STBY 00h The Standby Channel register controls which (if any) capacitive touch sensor inputs are active during Standby. Bit 5 - CS6_STBY - Controls whether the CS6 channel is active in Standby. `0' (default) - The CS6 channel not be sampled during Standby mode. `1' - The CS6 channel will be sampled during Standby Mode. It will use the Standby threshold setting, and the standby averaging and sensitivity settings. Bit 4 - CS5_STBY - Controls whether the CS5 channel is active in Standby. Bit 3 - CS4_STBY - Controls whether the CS4 channel is active in Standby. Bit 2 - CS3_STBY - Controls whether the CS3 channel is active in Standby. Bit 1 - CS2_STBY - Controls whether the CS2 channel is active in Standby. Bit 0 - CS1_STBY - Controls whether the CS1 channel is active in Standby. 5.21 Standby Configuration Register Table 5.36 Standby Configuration Register ADDR R/W REGISTER B7 41h R/W Standby Configuration AVG_ SUM B6 B5 B4 STBY_AVG[2:0] B3 B2 STBY_SAMP_ TIME[1:0] B1 B0 STBY_CY_TIME [1:0] DEFAULT 39h The Standby Configuration register controls averaging and cycle time for those sensor inputs that are active in Standby. This register is useful for detecting proximity on a small number of sensor inputs as Revision 1.32 (01-05-12) 60 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet it allows the user to change averaging and sample times on a limited number of sensor inputs and still maintain normal functionality in the fully active state. Bit 7 - AVG_SUM - Determines whether the active sensor inputs will average the programmed number of samples or whether they will accumulate for the programmed number of samples. `0' - (default) - The active sensor input delta count values will be based on the average of the programmed number of samples when compared against the threshold. `1' - The active sensor input delta count values will be based on the summation of the programmed number of samples when compared against the threshold. This bit should only be set when performing proximity detection as a physical touch will overflow the delta count registers and may result in false readings. Bits 6 - 4 - STBY_AVG[2:0] - Determines the number of samples that are taken for all active channels during the sensor cycle as shown in Table 5.37. All samples are taken consecutively on the same channel before the next channel is sampled and the result is averaged over the number of samples measured before updating the measured results. Table 5.37 STBY_AVG Bit Decode STBY_AVG[2:0] 2 1 0 NUMBER OF SAMPLES TAKEN PER MEASUREMENT 0 0 0 1 0 0 1 2 0 1 0 4 0 1 1 8 (default) 1 0 0 16 1 0 1 32 1 1 0 64 1 1 1 128 Bit 3-2 - STBY SAMP_TIME[1:0] - Determines the time to take a single sample when the device is in Standby as shown in Table 5.38. Table 5.38 STBY_SAMP_TIME Bit Decode STBY_SAMP_TIME[1:0] 1 0 SAMPLING TIME 0 0 320us 0 1 640us 1 0 1.28ms (default) 1 1 2.56ms Bits 1 - 0 - STBY_CY_TIME[2:0] - Determines the overall cycle time for all measured channels during standby operation as shown in Table 5.39. All measured channels are sampled at the beginning of the SMSC CAP1126 61 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet cycle time. If additional time is remaining, the device is placed into a lower power state for the remaining duration of the cycle. Table 5.39 STBY_CY_TIME Bit Decode STBY_CY_TIME[1:0] 1 0 OVERALL CYCLE TIME 0 0 35ms 0 1 70ms (default) 1 0 105ms 1 1 140ms APPLICATION NOTE: The programmed cycle time is only maintained if the total averaging time for all samples is less than the programmed cycle. The STBY_AVG[2:0] bits will take priority so that if more samples are required than would normally be allowed during the cycle time, the cycle time will be extended as necessary to accommodate the number of samples to be measured. 5.22 Standby Sensitivity Register Table 5.40 Standby Sensitivity Register ADDR R/W REGISTER B7 B6 B5 B4 B3 42h R/W Standby Sensitivity - - - - - B2 B1 B0 DEFAULT STBY_SENSE[2:0] 02h The Standby Sensitivity register controls the sensitivity for sensor inputs that are active in Standby. Bits 2 - 0 - STBY_SENSE[2:0] - Controls the sensitivity for sensor inputs that are active in Standby. The sensitivity settings act to scale the relative delta count value higher or lower based on the system parameters. A setting of 000b is the most sensitive while a setting of 111b is the least sensitive. At the more sensitive settings, touches are detected for a smaller delta C corresponding to a "lighter" touch. These settings are more sensitive to noise however and a noisy environment may flag more false touches than higher sensitivity levels. APPLICATION NOTE: A value of 128x is the most sensitive setting available. At the most sensitivity settings, the MSB of the Delta Count register represents 64 out of ~25,000 which corresponds to a touch of approximately 0.25% of the base capacitance (or a C of 25fF from a 10pF base capacitance). Conversely a value of 1x is the least sensitive setting available. At these settings, the MSB of the Delta Count register corresponds to a delta count of 8192 counts out of ~25,000 which corresponds to a touch of approximately 33% of the base capacitance (or a C of 3.33pF from a 10pF base capacitance). Revision 1.32 (01-05-12) 62 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 5.41 STBY_SENSE Bit Decode STBY_SENSE[2:0] 5.23 2 1 0 SENSITIVITY MULTIPLIER 0 0 0 128x (most sensitive) 0 0 1 64x 0 1 0 32x (default) 0 1 1 16x 1 0 0 8x 1 0 1 4x 1 1 0 2x 1 1 1 1x - (least sensitive) Standby Threshold Register Table 5.42 Standby Threshold Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 43h R/W Standby Threshold - 64 32 16 8 4 2 1 40h The Standby Threshold register stores the delta threshold that is used to determine if a touch has been detected. When a touch occurs, the input signal of the corresponding sensor pad changes due to the capacitance associated with a touch. If the sensor input change exceeds the threshold settings, a touch is detected. 5.24 Sensor Input Base Count Registers Table 5.43 Sensor Input Base Count Registers ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 50h R Sensor Input 1 Base Count 128 64 32 16 8 4 2 1 C8h 51h R Sensor Input 2 Base Count 128 64 32 16 8 4 2 1 C8h 52h R Sensor Input 3 Base Count 128 64 32 16 8 4 2 1 C8h 53h R Sensor Input 4 Base Count 128 64 32 16 8 4 2 1 C8h SMSC CAP1126 63 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 5.43 Sensor Input Base Count Registers (continued) ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 54h R Sensor Input 5 Base Count 128 64 32 16 8 4 2 1 C8h 55h R Sensor Input 6 Base Count 128 64 32 16 8 4 2 1 C8h The Sensor Input Base Count registers store the calibrated "Not Touched" input value from the capacitive touch sensor inputs. These registers are periodically updated by the re-calibration routine. The routine uses an internal adder to add the current count value for each reading to the sum of the previous readings until sample size has been reached. At this point, the upper 16 bits are taken and used as the Sensor Input Base Count. The internal adder is then reset and the re-calibration routine continues. The data presented is determined by the BASE_SHIFT[3:0] bits (see Section 5.5). 5.25 LED Output Type Register Table 5.44 LED Output Type Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 71h R/W LED Output Type - - - - - - LED2_ OT LED1_ OT 00h The LED Output Type register controls the type of output for the LED pins. Each pin is controlled by a single bit. Refer to application note 21.4 CAP1188 Family LED Configuration Options for more information about implementing LEDs. Bit 1 - LED2_OT - Determines the output type of the LED2 pin. `0' (default) - The LED2 pin is an open-drain output with an external pull-up resistor. When the appropriate pin is set to the "active" state (logic `1'), the pin will be driven low. Conversely, when the pin is set to the "inactive" state (logic `0'), then the pin will be left in a High Z state and pulled high via an external pull-up resistor. `1' - The LED2 pin is a push-pull output. When driving a logic `1', the pin is driven high. When driving a logic `0', the pin is driven low. Bit 0 - LED1_OT - Determines the output type of the LED1 pin. 5.26 Sensor Input LED Linking Register Table 5.45 Sensor Input LED Linking Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 72h R/W Sensor Input LED Linking - - - - - - CS2_ LED2 CS1_ LED1 00h Revision 1.32 (01-05-12) 64 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet The Sensor Input LED Linking register controls whether a capacitive touch sensor input is linked to an LED output. If the corresponding bit is set, then the appropriate LED output will change states defined by the LED Behavior controls (see Section 5.31) in response to the capacitive touch sensor input. Bit 1 - CS2_LED2 - Links the LED2 output to a detected touch on the CS2 sensor input. When a touch is detected, the LED is actuated and will behave as determined by the LED Behavior controls. `0' (default) - The LED 2 output is not associated with the CS2 input. If a touch is detected on the CS2 input, the LED will not automatically be actuated. The LED is enabled and controlled via the LED Output Control register (see Section 5.28) and the LED Behavior registers (see Section 5.31). `1' - The LED 2 output is associated with the CS2 input. If a touch is detected on the CS2 input, the LED will be actuated and behave as defined in Table 5.52. Bit 0 - CS1_LED1 - Links the LED1 output to a detected touch on the CS1 sensor input. When a touch is detected, the LED is actuated and will behave as determined by the LED Behavior controls. 5.27 LED Polarity Register Table 5.46 LED Polarity Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 73h R/W LED Polarity - - - - - - LED2_ POL LED1_ POL 00h The LED Polarity register controls the logical polarity of the LED outputs. When these bits are set or cleared, the corresponding LED Mirror controls are also set or cleared (unless the BLK_POL_MIR bit is set - see Section 5.6, "Configuration Registers"). Table 5.48, "LED Polarity Behavior" shows the interaction between the polarity controls, output controls, and relative brightness. APPLICATION NOTE: The polarity controls determine the final LED pin drive. A touch on a linked capacitive touch sensor input is treated in the same way as the LED Output Control bit being set to a logic `1'. APPLICATION NOTE: The LED drive assumes that the LEDs are configured such that if the LED pin is driven to a logic `0' then the LED will be on and that the CAP1126 LED pin is sinking the LED current. Conversely, if the LED pin is driven to a logic `1', the LED will be off and there is no current flow. See Figure 4.1, "System Diagram for CAP1126". APPLICATION NOTE: This application note applies when the LED polarity is inverted (LEDx_POL = `0'). For LED operation, the duty cycle settings determine the % of time that the LED pin will be driven to a logic `0' state in. The Max Duty Cycle settings define the maximum % of time that the LED pin will be driven low (i.e. maximum % of time that the LED is on) while the Min Duty Cycle settings determine the minimum % of time that the LED pin will be driven low (i.e. minimum % of time that the LED is on). When there is no touch detected or the LED Output Control register bit is at a logic `0', the LED output will be driven at the minimum duty cycle setting. Breathe operations will ramp the duty cycle from the minimum duty cycle to the maximum duty cycle. APPLICATION NOTE: This application note applies when the LED polarity is non-inverted (LEDx_POL = `1'). For LED operation, the duty cycle settings determine the % of time that the LED pin will be driven to a logic `1' state. The Max Duty Cycle settings define the maximum % of time that the LED pin will be driven high (i.e. maximum % of time that the LED is off) while the Min Duty Cycle settings determine the minimum % of time that the LED pin will be driven high (i.e. minimum % of time that the LED is off). When there is no touch detected or the LED Output Control register bit is at a logic `0', the LED output will be driven at 100 minus the minimum duty cycle setting. Breathe operations will ramp the duty cycle from 100 minus the minimum duty cycle to 100 minus the maximum duty cycle. SMSC CAP1126 65 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet APPLICATION NOTE: The LED Mirror controls (see Section 5.30, "LED Mirror Control Register") work with the polarity controls with respect to LED brightness but will not have a direct effect on the output pin drive. Bit 1 - LED2_POL - Determines the polarity of the LED2 output. `0' (default) - The LED2 output is inverted. For example, a setting of `1' in the LED Output Control register will cause the LED pin output to be driven to a logic `0'. `1' - The LED2 output is non-inverted. For example, a setting of `1' in the LED Output Control register will cause the LED pin output to be driven to a logic `1' or left in the high-z state as determined by its output type. Bit 0 - LED1_POL - Determines the polarity of the LED1 output. 5.28 LED Output Control Register Table 5.47 LED Output Control Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 74h R/W LED Output Control - - - - - - LED2_ DR LED1_ DR 00h The LED Output Control Register controls the output state of the LED pins that are not linked to sensor inputs. Note: If an LED is linked to a sensor input in the Sensor Input LED Linking Register (Section 5.26, "Sensor Input LED Linking Register"), the corresponding bit in the LED Output Control Register is ignored (i.e. a linked LED cannot be host controlled). The LED Polarity Control Register will determine the non actuated state of the LED pins. The actuated LED behavior is determined by the LED behavior controls (see Section 5.31, "LED Behavior Register"). Table 5.48 shows the interaction between the polarity controls, output controls, and relative brightness. Bit 1 - LED2_DR - Determines whether LED2 output is driven high or low. `0' (default) - The LED2 output is driven at the minimum duty cycle or not actuated. `1' - The LED2 output is High Z or driven at the maximum duty cycle or actuated. Bit 0 - LED1_DR - Determines whether LED1 output is driven high or low. Revision 1.32 (01-05-12) 66 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 5.48 LED Polarity Behavior LED OUTPUT CONTROL REGISTER OR TOUCH POLARITY MAX DUTY MIN DUTY BRIGHTNESS LED APPEARANCE inverted (`0') not used minimum % of time that the LED is on (logic 0) maximum brightness at min duty cycle on at min duty cycle 1 inverted (`0') maximum % of time that the LED is on (logic 0) minimum % of time that the LED is on (logic 0) maximum brightness at max duty cycle. Brightness ramps from min duty cycle to max duty cycle according to LED behavior 0 noninverted (`1') not used minimum % of time that the LED is off (logic 1) maximum brightness at 100 minus min duty cycle. on at 100 - min duty cycle minimum % of time that the LED is off (logic 1) For Direct behavior, maximum brightness is 100 minus max duty cycle. When breathing, max brightness is 100 minus min duty cycle. Brightness ramps from 100 - min duty cycle to 100 - max duty cycle. according to LED behavior 0 noninverted (`1') 1 5.29 maximum % of time that the LED is off (logic 1) Linked LED Transition Control Register Table 5.49 Linked LED Transition Control Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 77h R/W Linked LED Transition Control - - - - - - LED2_ LTRAN LED1_ LTRAN 00h The Linked LED Transition Control register controls the LED drive when the LED is linked to a capacitive touch sensor input. These controls work in conjunction with the INV_LINK_TRAN bit (see Section 5.6.2, "Configuration 2 - 44h") to create smooth transitions from host control to linked LEDs. Bit 1 - LED2_LTRAN - Determines the transition effect when LED2 is linked to CS2. `0' (default) - When the LED output control bit for CS2 is `1', and then CS2 is linked to LED2 and no touch is detected, the LED will change states. `1' - If the INV_LINK_TRAN bit is `1', when the LED output control bit for CS2 is `1', and then CS2 is linked to LED2 and no touch is detected, the LED will not change states. In addition, the LED state will change when the sensor pad is touched. If the INV_LINK_TRAN bit is `0', when the LED output control bit for CS2 is `1', and then CS2 is linked to LED2 and no touch is detected, the LED will not change states. However, the LED state will not change when the sensor pad is touched. SMSC CAP1126 67 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet APPLICATION NOTE: If the LED behavior is not "Direct" and the INV_LINK_TRAN bit it `0', the LED will not perform as expected when the LED2_LTRAN bit is set to `1'. Therefore, if breathe and pulse behaviors are used, set the INV_LINK_TRAN bit to `1'. Bit 0 - LED1_LTRAN - Determines the transition effect when LED1 is linked to CS1. 5.30 LED Mirror Control Register Table 5.50 LED Mirror Control Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 79h R/W LED Mirror Control - - - - - - LED2_ MIR _ EN LED1_ MIR _ EN 00h The LED Mirror Control Registers determine the meaning of duty cycle settings when polarity is noninverted for each LED channel. When the polarity bit is set to `1' (non-inverted), to obtain correct steps for LED ramping, pulse, and breathe behaviors, the min and max duty cycles need to be relative to 100%, rather than the default, which is relative to 0%. APPLICATION NOTE: The LED drive assumes that the LEDs are configured such that if the LED pin is driven to a logic `0', the LED will be on and the CAP1126 LED pin is sinking the LED current. When the polarity bit is set to `1', it is considered non-inverted. For systems using the opposite LED configuration, mirror controls would apply when the polarity bit is `0'. These bits are changed automatically if the corresponding LED Polarity bit is changed (unless the BLK_POL_MIR bit is set - see Section 5.6). Bit 1 - LED2_MIR_EN - Determines whether the duty cycle settings are "biased" relative to 0% or 100% duty cycle. `0' (default) - The duty cycle settings are determined relative to 0% and are determined directly with the settings. `1' - The duty cycle settings are determined relative to 100%. Bit 0 - LED1_MIR_EN - Determines whether the duty cycle settings are "biased" relative to 0% or 100% duty cycle. 5.31 LED Behavior Register Table 5.51 LED Behavior Register ADDR R/W REGISTER B7 B6 B5 B4 81h R/W LED Behavior 1 - - - - B3 B2 LED2_CTL[1:0] B1 B0 LED1_CTL[1:0] DEFAULT 00h The LED Behavior register controls the operation of LEDs. Each LED pin is controlled by a 2-bit field and the behavior is determined by whether the LED is linked to a capacitive touch sensor input or not. If the corresponding LED output is linked to a capacitive touch sensor input, the appropriate behavior will be enabled / disabled based on touches and releases. If the LED output is not associated with a capacitive touch sensor input, the appropriate behavior will be enabled / disabled by the LED Output Control register. If the respective LEDx_DR bit is set to a Revision 1.32 (01-05-12) 68 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet logic `1', this will be associated as a "touch", and if the LEDx_DR bit is set to a logic `0', this will be associated as a "release". Table 5.52, "LEDx_CTL Bit Decode" shows the behavior triggers. The defined behavior will activate when the Start Trigger is met and will stop when the Stop Trigger is met. Note the behavior of the Breathe Hold and Pulse Release option. The LED Polarity Control register will determine the non actuated state of the LED outputs (see Section 5.27, "LED Polarity Register"). APPLICATION NOTE: If an LED is not linked to a capacitive touch sensor input and is breathing (via the Breathe or Pulse behaviors), it must be unactuated and then re-actuated before changes to behavior are processed. For example, if the LED output is breathing and the Maximum duty cycle is changed, this change will not take effect until the LED output control register is set to `0' and then re-set to `1'. APPLICATION NOTE: If an LED is not linked to the capacitive touch sensor input and configured to operate using Pulse 1 Behavior, then the circuitry will only be actuated when the corresponding output control bit is set. It will not check the bit condition until the Pulse 1 behavior is finished. The device will not remember if the bit was cleared and reset while it was actuated. APPLICATION NOTE: If an LED is actuated and not linked and the desired LED behavior is changed, this new behavior will take effect immediately; however, the first instance of the changed behavior may act incorrectly (e.g. if changed from Direct to Pulse 1, the LED output may `breathe' 4 times and then end at minimum duty cycle). LED Behaviors will operate normally once the LED has been un-actuated and then re-actuated. APPLICATION NOTE: If an LED is actuated and it is switched from linked to a capacitive touch sensor input to unlinked (or vice versa), the LED will respond to the new command source immediately if the behavior was Direct or Breathe. For Pulse behaviors, it will complete the behavior already in progress. For example, if a linked LED was actuated by a touch and the control is changed so that it is unlinked, it will check the status of the corresponding LED Output Control bit. If that bit is `0', then the LED will behave as if a release was detected. Likewise, if an unlinked LED was actuated by the LED Output Control register and the control is changed so that it is linked and no touch is detected, then the LED will behave as if a release was detected. Bits 3 - 2 - LED2_CTL[1:0] - Determines the behavior of LED2 as shown in Table 5.52. Bits 1 - 0 - LED1_CTL[1:0] - Determines the behavior of LED1 as shown in Table 5.52. SMSC CAP1126 69 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 5.52 LEDx_CTL Bit Decode LEDX_CTL [1:0] 1 0 0 1 1 0 OPERATION 0 1 START TRIGGER STOP TRIGGER Release Detected or LED Output Control bit cleared Direct The LED is driven to the programmed state (active or inactive). See Figure 5.7 Touch Detected or LED Output Control bit set Pulse 1 The LED will "Pulse" a programmed number of times. During each "Pulse" the LED will breathe up to the maximum brightness and back down to the minimum brightness so that the total "Pulse" period matches the programmed value. Touch or Release Detected or LED Output Control bit set or cleared (see Section 5.32) n/a Pulse 2 The LED will "Pulse" when the start trigger is detected. When the stop trigger is detected, it will "Pulse" a programmable number of times then return to its minimum brightness. Touch Detected or LED Output Control bit set Release Detected or LED Output Control bit cleared Breathe The LED will breathe. It will be driven with a duty cycle that ramps up from the programmed minimum duty cycle (default 0%) to the programmed maximum duty cycle duty cycle (default 100%) and then back down. Each ramp takes up 50% of the programmed period. The total period of each "breath" is determined by the LED Breathe Period controls - see Section 5.34. Touch Detected or LED Output Control bit set Release Detected or LED Output Control bit cleared 0 1 DESCRIPTION APPLICATION NOTE: The PWM frequency is determined based on the selected LED behavior, the programmed breathe period, and the programmed min and max duty cycles. For the Direct behavior mode, the PWM frequency is calculated based on the programmed Rise and Fall times. If these are set at 0, then the maximum PWM frequency will be used based on the programmed duty cycle settings. 5.32 LED Pulse 1 Period Register Table 5.53 LED Pulse 1 Period Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 84h R/W LED Pulse 1 Period ST_ TRIG P1_ PER6 P1_ PER5 P1_ PER4 P1_ PER3 P1_ PER2 P1_ PER1 P1_ PER0 20h The LED Pulse Period 1 register determines the overall period of a pulse operation as determined by the LED_CTL registers (see Table 5.52 - setting 01b). The LSB represents 32ms so that a setting of 18h (24d) would represent a period of 768ms (24 x 32ms = 768ms). The total range is from 32ms to 4.064 seconds as shown in Table 5.54 with the default being 1024ms. Revision 1.32 (01-05-12) 70 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet APPLICATION NOTE: Due to constraints on the LED Drive PWM operation, any Breathe Period less than 160ms (05h) may not be achievable. The device will breathe at the minimum period possible as determined by the period and min / max duty cycle settings. Bit 7 - ST_TRIG - Determines the start trigger for the LED Pulse behavior. `0' (default) - The LED will Pulse when a touch is detected or the drive bit is set. `1' - The LED will Pulse when a release is detected or the drive bit is cleared. The Pulse 1 operation is shown in Figure 5.1 when the LED output is configured for non-inverted polarity (LEDx_POL = 1) and in Figure 5.2 for inverted polarity (LEDx_POL = 0). . Touch Detected or Release Detected X pulses after touch or after release Normal - untouched operation (100% - Pulse 1 Min Duty Cycle) * Brightness Normal - untouched operation LED Brightness (100% - Pulse 1 Max Duty Cycle) * Brightness Pulse 1 Period (P1_PER) Figure 5.1 Pulse 1 Behavior with Non-Inverted Polarity Touch Detected or Release Detected X pulses after touch or after release Pulse 1 Max Duty Cycle * Brightness LED Brightness Normal - untouched operation Normal - untouched operation Pulse 1 Min Duty Cycle * Brightness Pulse Period (P1_PER) Figure 5.2 Pulse 1 Behavior with Inverted Polarity SMSC CAP1126 71 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 5.54 LED Pulse / Breathe Period Example 5.33 SETTING (HEX) SETTING (DECIMAL) TOTAL BREATHE / PULSE PERIOD (MS) 00h 0 32 01h 1 32 02h 2 64 03h 3 96 ... ... ... 7Dh 125 4000 7Eh 126 4032 7Fh 127 4064 LED Pulse 2 Period Register Table 5.55 LED Pulse 2 Period Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 85h R/W LED Pulse 2 Period - P2_ PER6 P2_ PER5 P2_ PER4 P2_ PER3 P2_ PER2 P2_ PER1 P2_ PER0 14h The LED Pulse 2 Period register determines the overall period of a pulse operation as determined by the LED_CTL registers (see Table 5.52 - setting 10b). The LSB represents 32ms so that a setting of 18h (24d) would represent a period of 768ms. The total range is from 32ms to 4.064 seconds (see Table 5.54) with a default of 640ms. APPLICATION NOTE: Due to constraints on the LED Drive PWM operation, any Breathe Period less than 160ms (05h) may not be achievable. The device will breathe at the minimum period possible as determined by the period and min / max duty cycle settings. The Pulse 2 Behavior is shown in Figure 5.3 for non-inverted polarity (LEDx_POL = 1) and in Figure 5.4 for inverted polarity (LEDx_POL = 0). Revision 1.32 (01-05-12) 72 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Normal - untouched operation Release Detected Touch Detected Normal - untouched operation X additional pulses after release (100% - Pulse 2 Min Duty Cycle) * Brightness LED Brightness ... (100% - Pulse 2 Max Duty Cycle) * Brightness Pulse Period (P2_PER) Figure 5.3 Pulse 2 Behavior with Non-Inverted Polarity Normal - untouched operation Release Detected Touch Detected Normal - untouched operation X additional pulses after release Pulse 2 Max Duty Cycle * Brightness LED Brightness ... Pulse 2 Min Duty Cycle * Brightness Pulse Period (P2_PER) Figure 5.4 Pulse 2 Behavior with Inverted Polarity 5.34 LED Breathe Period Register Table 5.56 LED Breathe Period Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 86h R/W LED Breathe Period - BR_ PER6 BR_ PER5 BR_ PER4 BR_ PER3 BR_ PER2 BR_ PER1 BR_ PER0 5Dh The LED Breathe Period register determines the overall period of a breathe operation as determined by the LED_CTL registers (see Table 5.52 - setting 11b). The LSB represents 32ms so that a setting of 18h (24d) would represent a period of 768ms. The total range is from 32ms to 4.064 seconds (see Table 5.54) with a default of 2976ms. APPLICATION NOTE: Due to constraints on the LED Drive PWM operation, any Breathe Period less than 160ms (05h) may not be achievable. The device will breathe at the minimum period possible as determined by the period and min / max duty cycle settings. SMSC CAP1126 73 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet 5.35 LED Configuration Register Table 5.57 LED Configuration Register ADDR R/W REGISTER B7 B6 B5 88h R/W LED Config - RAMP_ ALERT B4 B3 PULSE2_CNT[2:0] B2 B1 B0 DEFAULT PULSE1_CNT[2:0] The LED Configuration register controls general LED behavior as well as the number of pulses that are sent for the PULSE LED output behavior. Bit 6 - RAMP_ALERT - Determines whether the device will assert the ALERT# pin when LEDs actuated by the LED Output Control register bits have finished their respective behaviors. Interrupts will only be generated if the LED activity is generated by writing the LED Output Control registers. Any LED activity associated with touch detection will not cause an interrupt to be generated when the LED behavior has been finished. `0' (default) - The ALERT# pin will not be asserted when LEDs actuated by the LED Output Control register have finished their programmed behaviors. `1' - The ALERT# pin will be asserted whenever any LED that is actuated by the LED Output Control register has finished its programmed behavior. Bits 5 - 3 - PULSE2_CNT[2:0] - Determines the number of pulses used for the Pulse 2 behavior as shown in Table 5.58. Bits 2 - 0 - PULSE1_CNT[2:0] - Determines the number of pulses used for the Pulse 1 behavior as shown in Table 5.58. Table 5.58 PULSEX_CNT Decode PULSEX_CNT[2:0] 2 1 0 NUMBER OF BREATHS 0 0 0 1 (default - Pulse 2) 0 0 1 2 0 1 0 3 0 1 1 4 1 0 0 5 (default - Pulse 1) 1 0 1 6 1 1 0 7 1 1 1 8 Revision 1.32 (01-05-12) 74 DATASHEET SMSC CAP1126 04h 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet 5.36 LED Duty Cycle Registers Table 5.59 LED Duty Cycle Registers ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT 90h R/W LED Pulse 1 Duty Cycle P1_MAX_DUTY[3:0] P1_MIN_DUTY[3:0] F0h 91h R/W LED Pulse 2 Duty Cycle P2_MAX_DUTY[3:0] P2_MIN_DUTY[3:0] F0h 92h R/W LED Breathe Duty Cycle BR_MAX_DUTY[3:0] BR_MIN_DUTY[3:0] F0h 93h R/W Direct Duty Cycle DR_MAX_DUTY[3:0] DR_MIN_DUTY[3:0] F0h The LED Duty Cycle registers determine the minimum and maximum duty cycle settings used for the LED for each LED behavior. These settings affect the brightness of the LED when it is fully off and fully on. The LED driver duty cycle will ramp up from the minimum duty cycle to the maximum duty cycle and back down again. APPLICATION NOTE: When operating in Direct behavior mode, changes to the Duty Cycle settings will be applied immediately. When operating in Breathe, Pulse 1, or Pulse 2 modes, the LED must be unactuated and then re-actuated before changes to behavior are processed. Bits 7 - 4 - X_MAX_DUTY[3:0] - Determines the maximum PWM duty cycle for the LED drivers as shown in Table 5.60. Bits 3 - 0 - X_MIN_DUTY[3:0] - Determines the minimum PWM duty cycle for the LED drivers as shown in Table 5.60. Table 5.60 LED Duty Cycle Decode X_MAX/MIN_DUTY [3:0] 3 2 1 0 MAXIMUM DUTY CYCLE MINIMUM DUTY CYCLE 0 0 0 0 7% 0% 0 0 0 1 9% 7% 0 0 1 0 11% 9% 0 0 1 1 14% 11% 0 1 0 0 17% 14% 0 1 0 1 20% 17% 0 1 1 0 23% 20% 0 1 1 1 26% 23% 1 0 0 0 30% 26% 1 0 0 1 35% 30% SMSC CAP1126 75 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 5.60 LED Duty Cycle Decode (continued) X_MAX/MIN_DUTY [3:0] 3 2 1 0 MAXIMUM DUTY CYCLE MINIMUM DUTY CYCLE 1 0 1 0 40% 35% 1 0 1 1 46% 40% 1 1 0 0 53% 46% 1 1 0 1 63% 53% 1 1 1 0 77% 63% 1 1 1 1 100% 77% 5.37 LED Direct Ramp Rates Register Table 5.61 LED Direct Ramp Rates Register ADDR R/W REGISTER B7 B6 94h R/W LED Direct Ramp Rates - - B5 B4 B3 RISE_RATE[2:0] B2 B1 B0 FALL_RATE[2:0] DEFAULT 00h The LED Direct Ramp Rates register control the rising and falling edge time of an LED that is configured to operate in Direct behavior mode. The rising edge time corresponds to the amount of time the LED takes to transition from its minimum duty cycle to its maximum duty cycle. Conversely, the falling edge time corresponds to the amount of time that the LED takes to transition from its maximum duty cycle to its minimum duty cycle. Bits 5 - 3 - RISE_RATE[2:0] - Determines the rising edge time of an LED when it transitions from its minimum drive state to its maximum drive state as shown in Table 5.62. Bits 2 - 0 - FALL_RATE[2:0] - Determines the falling edge time of an LED when it transitions from its maximum drive state to its minimum drive state as shown in Table 5.62. Table 5.62 Rise / Fall Rate Decode RISE_RATE/ FALL_RATE/ BIT DECODE 2 1 0 RISE / FALL TIME (TRISE / TFALL)) 0 0 0 0 0 0 1 250ms 0 1 0 500ms 0 1 1 750ms 1 0 0 1s 1 0 1 1.25s Revision 1.32 (01-05-12) 76 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 5.62 Rise / Fall Rate Decode (continued) RISE_RATE/ FALL_RATE/ BIT DECODE 2 1 0 RISE / FALL TIME (TRISE / TFALL)) 1 1 0 1.5s 1 1 1 2s 5.38 LED Off Delay Register Table 5.63 LED Off Delay Register ADDR R/W REGISTER B7 95h R/W LED Off Delay Register - B6 B5 B4 BR_OFF_DLY[2:0] B3 B2 B1 B0 DIR_OFF_DLY[3:0] DEFAULT 00h The LED Off Delay register determines the amount of time that an LED remains at its maximum duty cycle (or minimum as determined by the polarity controls) before it starts to ramp down. If the LED is operating in Breathe mode, this delay is applied at the top of each "breath". If the LED is operating in the Direct mode, this delay is applied when the LED is unactuated. Bits 6 - 4 - BR_OFF_DLY[2:0] - Determines the Breathe behavior mode off delay, which is the amount of time an LED in Breathe behavior mode remains inactive after it finishes a breathe pulse (ramp on and ramp off), as shown in Figure 5.5 (non-inverted polarity LEDx_POL = 1) and Figure 5.6 (inverted polarity LEDx_POL = 0). Available settings are shown in Table 5.64. LED Actuated LED Unactuated 100% - Breathe Max Min Cycle * Brightness LED Brightness Breathe Period (BR_PER) 100% - Breathe Min Duty Cycle * Brightness Breathe Off Delay (BR_OFF_DLY) Figure 5.5 Breathe Behavior with Non-Inverted Polarity SMSC CAP1126 77 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet LED Actuated LED Unactuated Breathe Max Duty Cycle * Brightness LED Brightness Breathe Min Duty Cycle * Brightness Breathe Period (BR_PER) Breathe Off Delay (BR_OFF_DLY) Figure 5.6 Breathe Behavior with Inverted Polarity Table 5.64 Breathe Off Delay Settings BR_OFF_DLY [2:0] 2 1 0 OFF DELAY 0 0 0 0 (default) 0 0 1 0.25s 0 1 0 0.5s 0 1 1 0.75s 1 0 0 1.0s 1 0 1 1.25s 1 1 0 1.5s 1 1 1 2.0s Bits 3 - 0 - DIR_OFF_DLY[3:0] - Determines the turn-off delay, as shown in Table 5.65, for all LEDs that are configured to operate in Direct behavior mode. The Direct behavior operation is determined by the combination of programmed Rise Time, Fall Time, Min and Max Duty cycles, Off Delay, and polarity. Figure 5.7 shows the behavior for non-inverted polarity (LEDx_POL = 1) while Figure 5.8 shows the behavior for inverted polarity (LEDx_POL = 0). Revision 1.32 (01-05-12) 78 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet N orm al - untouched operation R elease D etected Touch D etected N orm al - untouched operation (100% - M in D uty C ycle) * B rightness LE D B rightness R IS E _R A TE S etting (t R IS E ) (100% - M ax D uty C ycle) * B rightness O ff D elay (t O FF _D LY ) FA LL_R A TE S etting (t FA LL ) Figure 5.7 Direct Behavior for Non-Inverted Polarity Release Detected Touch Detected M ax Duty Cycle * Brightness LED Brightness Norm al - untouched operation M in Duty Cycle * Brightness Norm al - untouched operation RISE_RATE Setting (t R ISE ) O ff Delay (t OFF_DLY ) FALL_RATE Setting (t FALL ) Figure 5.8 Direct Behavior for Inverted Polarity Table 5.65 Off Delay Decode OFF DELAY[3:0] BIT DECODE 3 2 1 0 OFF DELAY (TOFF_DLY) 0 0 0 0 0 0 0 0 1 250ms 0 0 1 0 500ms 0 0 1 1 750ms 0 1 0 0 1s 0 1 0 1 1.25s 0 1 1 0 1.5s 0 1 1 1 2s 1 0 0 0 2.5s 79 Revision 1.32 (01-05-12) SMSC CAP1126 DATASHEET 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 5.65 Off Delay Decode (continued) OFF DELAY[3:0] BIT DECODE 3 2 1 0 OFF DELAY (TOFF_DLY) 1 0 0 1 3.0s 1 0 1 0 3.5s 1 0 1 1 4.0s 1 1 0 0 4.5s All others 5.39 5.0s Sensor Input Calibration Registers Table 5.66 Sensor Input Calibration Registers ADDR REGISTER R/W B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT B1h Sensor Input 1 Calibration R CAL1_9 CAL1_8 CAL1_7 CAL1_6 CAL1_5 CAL1_4 CAL1_3 CAL1_2 00h B2h Sensor Input 2 Calibration R CAL2_9 CAL2_8 CAL2_7 CAL2_6 CAL2_5 CAL2_4 CAL2_3 CAL2_2 00h B3h Sensor Input 3 Calibration R CAL3_9 CAL3_8 CAL3_7 CAL3_6 CAL3_5 CAL3_4 CAL3_3 CAL3_2 00h B4h Sensor Input 4 Calibration R CAL4_9 CAL4_8 CAL4_7 CAL4_6 CAL4_5 CAL4_4 CAL4_3 CAL4_2 00h B5h Sensor Input 5 Calibration R CAL5_9 CAL5_8 CAL5_7 CAL5_6 CAL5_5 CAL5_4 CAL5_3 CAL5_2 00h B6h Sensor Input 6 Calibration R CAL6_9 CAL6_8 CAL6_7 CAL6_6 CAL6_5 CAL6_4 CAL6_3 CAL6_2 00h B9h Sensor Input Calibration LSB 1 R CAL4_1 CAL4_0 CAL3_1 CAL3_0 CAL2_1 CAL2_0 CAL1_1 CAL1_0 00h BAh Sensor Input Calibration LSB 2 R - - - - CAL6_1 CAL6_0 CAL5_1 CAL5_0 00h The Sensor Input Calibration registers hold the 10-bit value that represents the last calibration value. Revision 1.32 (01-05-12) 80 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet 5.40 Product ID Register Table 5.67 Product ID Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT FDh R Product ID 0 1 0 1 0 0 1 1 53h The Product ID register stores a unique 8-bit value that identifies the device. 5.41 Manufacturer ID Register Table 5.68 Vendor ID Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT FEh R Manufacturer ID 0 1 0 1 1 1 0 1 5Dh The Vendor ID register stores an 8-bit value that represents SMSC. 5.42 Revision Register Table 5.69 Revision Register ADDR R/W REGISTER B7 B6 B5 B4 B3 B2 B1 B0 DEFAULT FFh R Revision 1 0 0 0 0 0 1 1 83h The Revision register stores an 8-bit value that represents the part revision. SMSC CAP1126 81 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Chapter 6 Package Information 6.1 CAP1126 Package Drawings Figure 6.1 16-Pin QFN 4mm x 4mm Package Drawing Revision 1.32 (01-05-12) 82 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Figure 6.2 16-Pin QFN 4mm x 4mm Package Dimensions Figure 6.3 16-Pin QFN 4mm x 4mm PCB Footprint SMSC CAP1126 83 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet 6.2 Package Marking TOP 0.41 LINE: 1 - SMSC Logo without circled (R) symbol LINE: 2 - Device ID, Version LINE: 3 - Last 7 digits of Lot Number LINE: 4 - Revision and Country Code (RCC) 3x 0.56 C 1 1 2 6 - 1 1 2 3 4 5 6 a R C C e3 PB-FREE/GREEN SYMBOL (Matte Sn) PIN 1 LINES 1 to 3: CENTER HORIZONTAL ALIGNMENT LINE 4: LEFT HORIZONTAL ALIGNMENT BOTTOM BOTTOM MARKING NOT ALLOWED Figure 6.4 CAP1126 Package Markings Revision 1.32 (01-05-12) 84 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Appendix A Device Delta A.1 Delta from CAP1026 to CAP1126 1. Updated circuitry to improve power supply rejection. 2. Updated LED driver duty cycle decode values to have more distribution at lower values - closer to a logarithmic curve. See Table 5.60, "LED Duty Cycle Decode". 3. Updated bug that breathe periods were not correct above 2.6s. This includes rise / fall time decodes above 1.5s. 4. Added filtering on RESET pin to prevent errant resets. 5. Updated controls so that the RESET pin assertion places the device into the lowest power state available and causes an interrupt when released. See Section 4.2, "RESET Pin". 6. Added 1 bit to the LED Off Delay register (see Section 5.38, "LED Off Delay Register") to extend times from 2s to 5s in 0.5s intervals. 7. Breathe behavior modified. A breathe off delay control was added to the LED Off Delay Register (see Section 5.38, "LED Off Delay Register") so the LEDs can be configured to remain inactive between breathes. 8. Added controls for the LED transition effects when linking LEDs to capacitive sensor inputs. See Section 5.29, "Linked LED Transition Control Register". 9. Added controls to "mirror" the LED duty cycle outputs so that when polarity changes, the LED brightness levels look right. These bits are automatically set when polarity is set. Added control to break this auto-set behavior. See Section 5.30, "LED Mirror Control Register". 10. Added Multiple Touch Pattern detection circuitry. See Section 5.15, "Multiple Touch Pattern Configuration Register". 11. Added General Status register to flag Multiple touches, Multiple Touch Pattern issues and general touch detections. See Section 5.2, "Status Registers". 12. Added bits 6 and 5 to the Recalibration Configuration register (2Dh - see Section 5.17, "Recalibration Configuration Register"). These bits control whether the accumulation of intermediate data and the consecutive negative delta counts counter are cleared when the noise status bit is set. 13. Added Configuration 2 register for LED linking controls, noise detection controls, and control to interrupt on press but not on release. Added control to change alert pin polarity. See Section 5.6, "Configuration Registers". 14. Updated Deep Sleep behavior so that device does not clear DSLEEP bit on received communications but will wake to communicate. 15. Changed PWM frequency for LED drivers. The PWM frequency was derived from the programmed breathe period and duty cycle settings and it ranged from ~4Hz to ~8000 Hz. The PWM frequency has been updated to be a fixed value of ~2000Hz. 16. Register delta: Table A.1 Register Delta From CAP1026 to CAP1126 ADDRESS REGISTER DELTA DELTA DEFAULT 00h Page 41 Changed - Main Status / Control added bits 7-6 to control gain 00h 02h Page 42 New - General Status new register to store MTP, MULT, LED, RESET, and general TOUCH bits 00h SMSC CAP1126 85 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table A.1 Register Delta From CAP1026 to CAP1126 (continued) ADDRESS REGISTER DELTA DELTA DEFAULT 44h Page 46 New - Configuration 2 new register to control alert polarity, LED touch linking behavior, LED output behavior, and noise detection, and interrupt on release 40h 24h Page 51 Changed - Averaging Control updated register bits - moved SAMP_AVG[2:0] bits and added SAMP_TIME bit 1. Default changed 39h 2Bh Page 55 New - Multiple Touch Pattern Configuration new register for Multiple Touch Pattern configuration - enable and threshold settings 80h 2Dh Page 56 New - Multiple Touch Pattern Register new register for Multiple Touch Pattern detection circuitry - pattern or number of sensor inputs 3Fh 2Fh Page 57 Changed Recalibration Configuration updated register - updated CAL_CFG bit decode to add a 128 averages setting and removed highest time setting. Default changed. Added bit 6 NO_CLR_INTD and bit 5 NO_CLR_NEG. 8Ah 38h Page 59 Changed - Sensor Input Noise Threshold updated register bits - removed bits 7 - 3 and consolidated all controls into bits 1 0. These bits will set the noise threshold for all channels. Default changed 01h 39h Removed - Noise Threshold Register 2 removed register n/a 41h Page 60 Changed - Standby Configuration updated register bits - moved STBY_AVG[2:0] bits and added STBY_TIME bit 1. Default changed 39h 77h Page 67 New - Linked LED Transition Control new register to control transition effect when LED linked to sensor inputs 00h 79h Page 68 New - LED Mirror Control new register to control LED output mirroring for brightness control when polarity changed 00h 90h Page 75 Changed - LED Pulse 1 Duty Cycle changed bit decode to be more logarithmic F0h 91h Page 75 Changed - LED Pulse 2 Duty Cycle changed bit decode to be more logarithmic F0h 92h Page 75 Changed - LED Breathe Duty Cycle changed bit decode to be more logarithmic F0h 93h Page 75 Changed - LED Direct Duty Cycle changed bit decode to be more logarithmic F0h 95h Added controls - LED Off Delay Added bits 6-4 BR_OFF_DLY[2:0] Added bit 3 DIR_OFF_DLY[3] 00h FDh Page 81 Changed - Product ID Changed bit decode for CAP1126 53h Revision 1.32 (01-05-12) 86 DATASHEET SMSC CAP1126 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Chapter 7 Datasheet Revision History Table 7.1 Customer Revision History REVISION LEVEL & DATE Rev. 1.32 (01-05-12) SECTION/FIGURE/ENTRY CORRECTION Table 2.2, "Electrical Specifications" Added conditions for tHD:DAT. Section 3.2.7, "SMBus and I2C Compatibility" Renamed from "SMBus and I2C Compliance." First paragraph, added last sentence: "For information on using the CAP1126 in an I2C system, refer to SMSC AN 14.0 SMSC Dedicated Slave Devices in I2C Systems." Added: CAP1126 supports I2C fast mode at 400kHz. This covers the SMBus max time of 100kHz. Section 5.4, "Sensor Input Delta Count Registers" Changed negative value cap from FFh to 80h. Section 3.3.3, "SMBus Send Byte" Added an application note: The Send Byte protocol is not functional in Deep Sleep (i.e., DSLEEP bit is set). Section 3.3.4, "SMBus Receive Byte" Added an application note: The Receive Byte protocol is not functional in Deep Sleep (i.e., DSLEEP bit is set). Rev. 1.3 (05-18-11) Section 5.42, "Revision Register" Updated revision ID from 82h to 83h. Rev. 1.2 (02-10-11) Section A.8, "Delta from Rev B (Mask B0) to Rev C (Mask B1)" Added. Cover Corrected block diagram. ALERT#/BC_IRQ# is an output, not an input. Table 1.1, "Pin Description for CAP1126" Changed value in "Unused Connection" column for the ADDR_COMM pin from "Connect to Ground" to "n/a". Table 2.2, "Electrical Specifications" PSR improvements made in functional revision B. Changed PSR spec from 100 typ and 200 max counts / V to 3 and 10 counts / V. Conditions updated. Section 4.5.2, "Recalibrating Sensor Inputs" Added more detail with subheadings for each type of recalibration. Section 5.6, "Configuration Registers" Added bit 5 BLK_PWR_CTRL to the Configuration 2 Register 44h. The TIMEOUT bit is set to `1' by default for functional revision B and is set to `0' by default for functional revision C. Section 5.42, "Revision Register" Updated revision ID in register FFh from 81h to 82h. Document Updated for functional revision B. See Section A.7, "Delta from Rev A (Mask A0) to Rev B (Mask B0)". Rev. 1.31 (08-18-11) Rev. 1.1 (11-17-10) SMSC CAP1126 87 DATASHEET Revision 1.32 (01-05-12) 6 Channel Capacitive Touch Sensor with 2 LED Drivers Datasheet Table 7.1 Customer Revision History (continued) REVISION LEVEL & DATE SECTION/FIGURE/ENTRY Cover CORRECTION Added to General Description: "includes circuitry and support for enhanced sensor proximity detection." Added the following Features: Rev. 1.0 (06-14-10) Revision 1.32 (01-05-12) Calibrates for Parasitic Capacitance Analog Filtering for System Noise Sources Press and Hold feature for Volume-like Applications Table 2.2, "Electrical Specifications" Conditions for Power Supply Rejection modified adding the following: Sampling time = 2.56ms Averaging = 1 Negative Delta Counts = Disabled All other parameters default Section 5.11, "Calibration Activate Register" Updated register description to indicate which recalibration routine is used. Section 5.14, "Multiple Touch Configuration Register" Updated register description to indicate what will happen. Table 5.34, "CSx_BN_TH Bit Decode" Table heading changed from "Threshold Divide Setting" to "Percent Threshold Setting". Initial release 88 DATASHEET SMSC CAP1126 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Microchip: CAP1126-1-AP-TR