HMC427LP3 / 427LP3E v07.0805 GaAs MMIC POSITIVE CONTROL TRANSFER SWITCH, DC* - 8 GHz Typical Applications Features The HMC427LP3 / HMC427LP3E is ideal for: High Isolation: 40 ~ 45 dB thru 6 GHz * Test Instrumentation Low Insertion Loss: 1.2 dB@ 6 GHz * Fiber Optics & Broadband Telecom Non-Reflective Design * Basestation Infrastructure 3 x 3 mm SMT Package * Microwave Radio & VSAT * Military Radios, Radar, & ECM Functional Diagram General Description The HMC427LP3 & HMC427LP3E are low loss broadband positive control transfer switches in leadless surface mount packages. Covering DC to 8 GHz, this switch offers high isolation and low insertion loss. The switch operates using a positive control voltage of 0/+5V and requires a fixed bias of +5V @ < 20 A. SWITCHES - SMT 10 * Blocking capacitors are required at ports RF1, 2, 3, & 4. Their value will determine the lowest transmission frequency. Electrical Specifi cations, TA = +25 C, With 0/+5V Control, 50 Ohm System Parameter Insertion Loss Isolation DC - 1.0 GHz DC - 2.0 GHz DC - 6.0 GHz DC - 8.0 GHz Return Loss DC - 6.0 GHz DC - 8.0 GHz Input Power for 1 dB Compression 1.0 - 8.0 GHz Input Third Order Intercept (Two-Tone Input Power= +7 dBm Each Tone, 1 MHz Tone Separation) 1.0 - 8.0 GHz Switching Characteristics tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) 10 - 256 Frequency DC - 6.0 GHz DC - 8.0 GHz Min. 42 37 33 27 Typ. Max. Units 1.2 1.6 1.6 2.1 dB dB 48 42 38 32 dB dB dB dB 17 15 dB dB 23 26 dBm 37 43 dBm 2 4 ns ns DC - 8.0 GHz For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC427LP3 / 427LP3E v07.0805 GaAs MMIC POSITIVE CONTROL TRANSFER SWITCH, DC* - 8 GHz Insertion Loss vs. Temperature Isolation 0 -10 -1 ISOLATION (dB) -2 -3 +25 C +85 C -40 C -4 RF4 to RF1 RF2 to RF3 RF4 to RF2 RF1 to RF3 -20 -30 -40 -50 -5 -60 0 1 2 3 4 5 6 7 8 9 0 1 2 3 FREQUENCY (GHz) Return Loss 5 6 7 8 9 10 0.1 and 1 dB Input Compression Point 0 INPUT COMPRESSION POINT (dBm) 30 -5 RF1 RF2 RF3 RF4 -10 -15 -20 -25 -30 28 26 24 22 20 18 16 1 dB Compression Point 0.1 dB Compression Point 14 12 10 0 1 2 3 4 5 6 7 8 9 1 2 3 4 FREQUENCY (GHz) 5 6 7 8 9 FREQUENCY (GHz) Input Third Order Intercept Point INPUT THIRD ORDER INTERCEPT POINT (dBm) RETURN LOSS (dB) 4 FREQUENCY (GHz) SWITCHES - SMT INSERTION LOSS (dB) 0 50 45 40 35 +25 C +85 C -40 C 30 25 20 1 2 3 4 5 6 7 8 9 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 257 HMC427LP3 / 427LP3E v07.0805 Absolute Maximum Ratings SWITCHES - SMT 10 10 - 258 Bias Voltage Range (Vdd) +7.0 Vdc Control Voltage Range (A & B) -0.5V to Vdd +1.0 Vdc Channel Temperature GaAs MMIC POSITIVE CONTROL TRANSFER SWITCH, DC* - 8 GHz Bias Voltage & Current Vdd Range = +5.0 Vdc 10 % 150 C Vdd (Vdc) Idd (Typ.) (A) Idd (Max.) (A) Thermal Resistance 130 C/W +5.0 5 10 Storage Temperature -65 to +150 C Operating Temperature -40 to +85 C Maximum Input Power +27 dBm State Bias Condition ESD Sensitivity (HBM) Class 1A Low 0 to +0.2 Vdc @ 5 A Typical High Vdd 0.2 Vdc @ 5 A Typical ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Note: DC blocking capacitors are required at ports RF1, 2, 3, & 4. Their value will determine the lowest transmission frequency. Control Voltages Truth Table Control Input A B Low High High Low Signal Path State RF4 to RF2 RF1 to RF3 RF4 to RF1 RF2 to RF3 On On Off Off Off Off On On For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC427LP3 / 427LP3E v07.0805 GaAs MMIC POSITIVE CONTROL TRANSFER SWITCH, DC* - 8 GHz Outline Drawing SWITCHES - SMT 10 NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC427LP3 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC427LP3E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] 427 XXXX [2] 427 XXXX [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 259 HMC427LP3 / 427LP3E v07.0805 GaAs MMIC POSITIVE CONTROL TRANSFER SWITCH, DC* - 8 GHz Pin Descriptions SWITCHES - SMT 10 10 - 260 Pin Number Function Description 1, 4, 9, 12 RF4, RF1, RF3, RF2 This pin is DC coupled and matched to 50 Ohm. Blocking capacitors are required. 2, 3, 5, 8, 10, 11, 13, 14, 16 N/C This pin should be connected to PCB RF ground to maximize isolation. GND Package bottom has exposed metal paddle that must be connected to PCB RF ground. 6 CTRLA See truth table and control voltage table. 7 CTRLB See truth table and control voltage table. 15 VDD Supply Voltage +5V 10%. Interface Schematic For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC427LP3 / 427LP3E v07.0805 GaAs MMIC POSITIVE CONTROL TRANSFER SWITCH, DC* - 8 GHz Evaluation PCB SWITCHES - SMT 10 List of Materials for Evaluation PCB 105672 [1] Item Description J1 - J4 PCB Mount SMA RF Connector J5 - J8 DC Pin C1 1000 pF Capacitor, 0603 Pkg. C2 - C5 100 pF Capacitor, 0402 Pkg. R1 - R2 100 Ohm Resistor, 0603 Pkg. U1 HMC427LP3 / HMC427LP3E Transfer Switch PCB [2] 105674 Evaluation PCB The circuit board used in the final application should be generated with proper RF circuit design techniques. Signal lines at the RF port should have 50 ohm impedance and the package ground leads and package bottom should be connected directly to the ground plane similar to that shown above. The evaluation circuit board shown above is available from Hittite Microwave Corporation upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 261