New Product TSOP581.., TSOP583.., TSOP591.., TSOP593.., TSOP585.., TSOP595.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES * Low supply current * Photo detector and preamplifier in one package * Internal filter for PCM frequency * Improved shielding against EMI * Supply voltage: 2.5 V to 5.5 V * Suitable for short bursts: burst length 6 carrier cycles * Improved immunity against ambient light * Insensitive to supply voltage ripple and noise * Compliant to RoHS Directive 2011/65/EU and in accordance to WEEE 2002/96/EC 19026 MECHANICAL DATA Note ** Please see document "Vishay Material Category Policy": www.vishay.com/doc?99902 Pinning for TSOP581.., TSOP583.., TSOP585: 1 = OUT, 2 = GND, 3 = VS DESCRIPTION Pinning for TSOP591.., TSOP593.., TSOP595: These products are miniaturized receiversfor infrared remote control systems. A PIN diode and a preamplifier are assembled on a lead frame, the epoxy package acts as an IR filter. The demodulated output signal can be directly decoded by a microprocessor. The TSOP581.., TSOP591.. are compatible with all common IR remote control data formats. The TSOP593.., TSOP583.. are optimized to better suppress spurious pulses from energy saving fluorescent lamps. The TSOP585.., TSOP595.. have an excellent noise suppression. It is immune to dimmed LCD backlighting and any fluorescent lamps. AGC3 and AGC5 may also suppress some data signals in case of continuous transmission. This component has not been qualified according to automotive specifications. 1 = OUT, 2 = VS, 3 = GND Please see the document "Product Transition Schedule" at www.vishay.com/ir-receiver-modules/ for up-to-date info, when this product will be released. PARTS TABLE SHORT BURST AND HIGH DATA RATE (AGC1) CARRIER FREQUENCY 1 = OUT, 2 = GND, 3 = VS TSOP58130 TSOP58133 TSOP58136 TSOP58138 TSOP58140 TSOP58156 30 kHz 33 kHz 36 kHz 38 kHz 40 kHz 56 kHz 1 = OUT, 2 = VS, 3 = GND TSOP59130 TSOP59133 TSOP59136 TSOP59138 TSOP59140 TSOP59156 NOISY ENVIRONMENTS AND SHORT BURSTS (AGC3) PINNING 1 = OUT, 2 = GND, 1 = OUT, 2 = VS, 3 = VS 3 = GND TSOP58330 TSOP59330 TSOP58333 TSOP59333 TSOP58336 TSOP59336 TSOP58338 TSOP59338 TSOP58340 TSOP59340 TSOP58356 TSOP59356 BLOCK DIAGRAM 17170-10 Transmitter with TSALxxxx 3 1 AGC Band pass Demodulator R1 VS + VS C1 C OUT GND VO GND The external components R1 and C1 are optional to improve the robustness against electrical overstress (typical values are R1 = 100 , C1 = 0.1 F). 2 Rev. 1.0, 23-Feb-11 1 = OUT, 2 = VS, 3 = GND TSOP59530 TSOP59533 TSOP59536 TSOP59538 TSOP59540 TSOP59556 IR receiver Circuit 33 k PIN 1 = OUT, 2 = GND, 3 = VS TSOP58530 TSOP58533 TSOP58536 TSOP58538 TSOP58540 TSOP58556 APPLICATION CIRCUIT 16833_14 Input VERY NOISY ENVIRONMENTS AND SHORT BURSTS (AGC5) Control circuit 1 Document Number: 82462 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 New Product TSOP581.., TSOP583.., TSOP591.., TSOP593.., TSOP585.., TSOP595.. www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL VALUE Supply voltage TEST CONDITION VS - 0.3 to + 6 V Supply current IS 5 mA V Output voltage Voltage at output to supply VO - 0.3 to 5.5 VS - VO - 0.3 to (VS + 0.3) V IO 5 mA Output current Junction temperature Storage temperature range Operating temperature range Tj 100 C Tstg - 25 to + 85 C Tamb - 25 to + 85 C Tamb 85 C Ptot 10 mW t 10 s, 1 mm from case Tsd 260 C Power consumption Soldering temperature UNIT Note * Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability. ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. VS 2.5 VS = 5 V, Ev = 0 ISD 0.55 Ev = 40 klx, sunlight ISH 0.8 mA Ev = 0, IR diode TSAL6200, IF = 250 mA, test signal see fig. 1 d 40 m Output voltage low IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see fig. 1 VOSL Minimum irradiance Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 Ee min. Maximum irradiance tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 Ee max. Directivity Angle of half transmission distance 1/2 Supply voltage Supply current Transmission distance TYP. MAX. 0.7 0.2 UNIT 5.5 V 0.9 mA 100 mV 0.4 mW/m2 W/m2 50 45 deg TYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) 0.5 Optical Test Signal (IR diode TSAL6200, IF = 0.4 A, N = 6 pulses, f = f0, t = 10 ms) tpo - Output Pulse Width (ms) Ee t tpi *) T *) tpi 6/f0 is recommended for optimal function Output Signal VO 1) 2) VOH VOL 14337 3/f0 < td < 9/f0 tpi - 4/f0 < tpo < tpi + 6/f0 = 950 nm, optical test signal, Fig. 1 0.4 0.3 Output pulse width 0.2 Input burst length 0.1 0 0.1 td 1) tpo 2) t Fig. 1 - Output Active Low Rev. 1.0, 23-Feb-11 10 1000 100 000 Ee - Irradiance (mW/m2) Fig. 2 - Pulse Length and Sensitivity in Dark Ambient 2 Document Number: 82462 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 New Product TSOP581.., TSOP583.., TSOP591.., TSOP593.., TSOP585.., TSOP595.. www.vishay.com Vishay Semiconductors 600 s t 600 s t = 60 ms 94 8134 Output Signal, (see fig. 4) VO VOH VOL t on 5.0 Ee min. - Threshold Irradiance (mW/m2) Optical Test Signal Ee Correlation with Ambient Light Sources: 4.5 10 W/m2 = 1.4 kLx (Std. illum. A, T = 2855 K) 2 4.0 10 W/m = 8.2 kLx (Daylight, T = 5900 K) 3.5 2.5 2.0 1.5 1.0 0.5 0 0.01 t t off Wavelength of Ambient Illumination: = 950 nm 3.0 0.8 ton 0.6 0.5 toff 0.4 0.3 0.2 = 950 nm, optical test signal, Fig. 1 0.1 0 0.1 1 10 100 Ee - Irradiance 1000 10 100 1.0 f = f0 0.9 0.8 0.7 f = 30 kHz 0.6 0.5 f = 20 kHz 0.4 f = 10 kHz 0.3 0.2 0.1 f = 100 Hz 0 1 10 000 10 100 1000 VsRMS - AC Voltage on DC Supply Voltage (mV) (mW/m2) Fig. 4 - Output Pulse Diagram Fig. 7 - Sensitivity vs. Supply Voltage Disturbances 500 E - Max. Field Strength (V/m) 1.2 Ee min./Ee - Rel. Responsivity 1 Fig. 6 - Sensitivity in Bright Ambient Ee min. - Threshold Irradiance (mW/m2) ton, toff - Output Pulse Width (ms) Fig. 3 - Output Function 0.7 0.1 Ee - Ambient DC Irradiance (W/m2) 1.0 0.8 0.6 0.4 f = f0 5 % f (3 dB) = f0/7 0.2 450 400 350 300 250 200 150 100 50 0.0 0 0.7 16926 0.9 1.1 1.3 0 20747 f/f0 - Relative Frequency Fig. 5 - Frequency Dependence of Responsivity Rev. 1.0, 23-Feb-11 500 1000 1500 2000 2500 3000 f - EMI Frequency (MHz) Fig. 8 - Sensitivity vs. Electric Field Disturbances 3 Document Number: 82462 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 New Product TSOP581.., TSOP583.., TSOP591.., TSOP593.., TSOP585.., TSOP595.. www.vishay.com Vishay Semiconductors 0.9 0 10 20 30 Max. Envelope Duty Cycle 0.8 TSOP581.., TSOP591.. 0.7 0.6 40 1.0 0.5 TSOP583.., TSOP593.. 0.4 0.3 0.9 50 0.8 60 0.2 70 0.7 0.1 80 TSOP585.., TSOP595.. 0 0 20 40 60 80 100 120 140 0.6 Burst Length (number of cycles/burst) 0.4 19258 0.2 0 drel - Relative Transmission Distance Fig. 9 - Max. Envelope Duty Cycle vs. Burst Length Fig. 12 - Horizontal Directivity 0.40 0 10 20 30 Ee min. - Sensitivity (mW/m2) 0.35 0.30 40 0.25 1.0 0.20 0.9 50 0.8 60 0.15 0.10 70 0.7 0.05 80 0 - 30 - 10 10 30 50 70 90 0.6 Tamb - Ambient Temperature (C) 0.4 0.8 1.2 1.0 0.8 0.6 0.4 0.2 94 8408 850 950 1050 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 1.5 1150 - Wavelength (nm) 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VS - Supply Voltage (V) Fig. 11 - Relative Spectral Sensitivity vs. Wavelength Rev. 1.0, 23-Feb-11 0 Fig. 13 - Vertical Directivity Ee min. - Sensitivity (mW/m2) S ()rel - Relative Spectral Sensitivity Fig. 10 - Sensitivity vs. Ambient Temperature 0 750 0.2 d rel - Relative Transmission Distance 19259 Fig. 14 - Sensitivity vs. Supply Voltage 4 Document Number: 82462 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 New Product TSOP581.., TSOP583.., TSOP591.., TSOP593.., TSOP585.., TSOP595.. www.vishay.com Vishay Semiconductors SUITABLE DATA FORMAT IR Signal These products are designed to suppress spurious output pulses due to noise or disturbance signals. Data and disturbance signals can be distinguished by the devices according to carrier frequency, burst length and envelope duty cycle. The data signal should be close to the band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. When a data signal is applied to the IR receiver in the presence of a disturbance signal, the sensitivity of the receiver is reduced to insure that no spurious pulses are present at the output. Some examples of disturbance signals which are suppressed are: * DC light (e.g. from tungsten bulb or sunlight) 0 10 5 15 20 Time (ms) 16920 * Continuous signals at any frequency Fig. 15 - IR Signal from Fluorescent Lamp with Low Modulation IR Signal * Modulated IR signals from common fluorescent lamps (example of noise pattern is shown in fig. 15 or fig. 16) 0 5 10 15 20 Time (ms) 16921 Fig. 16 - IR Signal from Fluorescent Lamp with High Modulation TSOP581.., TSOP591.. TSOP583.., TSOP593.. TSOP585.., TSOP595.. Minimum burst length 6 cycles/burst 6 cycles/burst 6 cycles/burst After each burst of length a minimum gap time is required of 6 to 70 cycles 10 cycles 6 to 35 cycles 10 cycles 6 to 24 cycles 10 cycles For bursts greater than a minimum gap time in the data stream is needed of 70 cycles > 1.1 x burst length 35 cycles > 6 x burst length 24 cycles > 25 ms Maximum number of continuous short bursts/second 2000 2000 2000 Recommended for NEC code yes yes yes Recommended for RC5/RC6 code yes yes yes Recommended for Sony code yes no no Recommended for RECS-80 code yes yes yes Recommended for RCMM code yes yes yes Recommended for r-step code yes yes yes Recommended for XMP code yes yes yes Common disturbance signals are supressed (example: signal pattern of fig. 14) Internference signals from lamps with high modulation are suppressed (examples: signal pattern of fig. 14 and fig. 15) Even critical disturbance signals like dimmed LCD backlighting are suppressed Suppression of interference from fluorescent lamps Note * For data formats with long bursts (more than 10 carrier cycles) please see the datasheet for TSOP582.., TSOP592.., TSOP584.., TSOP594.. Rev. 1.0, 23-Feb-11 5 Document Number: 82462 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 New Product TSOP581.., TSOP583.., TSOP591.., TSOP593.., TSOP585.., TSOP595.. www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 5 4.8 (4) 2.8 (5.55) 6.95 0.3 8.25 0.3 R2 0.9 1.1 30.5 0.5 (1.54) 0.85 max. 0.7 max. 2.54 nom. 2.54 nom. 0.5 max. 1.2 0.2 Marking area technical drawings according to DIN specifications Not indicated to lerances 0.2 Drawing-No.: 6.550-5263.01-4 Issue: 12; 16.04.10 19009 Rev. 1.0, 23-Feb-11 R2 6 Document Number: 82462 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Revision: 12-Mar-12 1 Document Number: 91000