P2005A-08TT - Alliance Semiconductor

October 2003 P2005A/S

rev 1.0

Alliance Semiconductor

2575, Augustine Drive • Santa Clara, CA • Tel: 408.855.4900 • Fax: 408.855 .4999 • www.alsc.com

Notice: The information in this document is subject to change without notice.

Low Frequency EMI Reduction IC

Features

 FCC approved method of EMI attenuation.

 Provides up to 15dB of EMI suppression.

 Generates a 1X or ½ X low EMI spread spectrum

clock of the input frequency.

 Input frequency range: 8MHz to 32MHz.

 Internal loop filter minimizes external components

and board space.

 Frequency deviation:

o P2005A: ± 1% to ± 3%

o P2005S: ± 0.6% to ± 1.8%

 SSON# control pin for spread spectrum enable

and disable options.

 Low cycle-to-cycle jitter.

 3.3V or 5V operating voltage range.

 16mA output drives.

 TTL or CMOS compatible outputs.

 Ultra-low power CMOS design.

 Available in 8-pin SOIC and TSSOP.

Product Description

The P2005X is a versatile spread spectrum frequency

modulator designed specifically for input clock

frequencies from 8MHz to 32MHz. Refer Output

Frequency Selection T abl e. The P2005X can generate an

EMI reduced clock from crystal, ceramic resonator, or

system clock. The P2005X offers various percentage

deviations ranging form ±0.6% to ±3.0%. Refer

Frequency Deviation Selections Table. The P2005X

reduces electromagnetic interference (EMI) at the clock

source, allowing system wide reduction of EMI of down

stream clock and data dependent signals. The P2005X

allows significant system cost savings by reducing the

number of circuit board layers ferrite beads, shielding

and other passive components that are traditionally

required to pass EMI regulations.

The P2005X uses the most efficient and optimized

modulation profile approved by the FCC and is

implemented in a proprietary all digital method.

The P2005X modulates the output of a single PLL in

order to “spread” the bandwidth of a synthesized clock,

and more importantly, decreases the peak amplitudes of

its harmonics. This results in significantly lower system

EMI compared to the typical narrow band signal produced

by oscillators and most frequency generators. Lowering

EMI by increasing a signal’s bandwidth is called ‘spread

spectrum clock generation’.

Applications

The P2005X is targeted towards EMI management for

high-speed digital applications such as PC peripheral

devices, consumer electronics and embedded controller

systems.

Block Diagram

VSS

XIN

Frequency

Divider

Feedback

Divider

Modulation

Phase

Detector Loop

Filter VCO Output

Divider

MODOUT

PLL

VDD

SSON# DIV2

SR0

Crystal

Oscillator

XOUT

October 2003 P2005X

rev 1.0

General purpose EMI Reduction IC 2 of 10

Notice: The information in this document is subject to change without notice.

XOUT

4 5

P2005X

XIN /CL

VSS

SR0

SSON#

ModOUT

Pin Configuration

Pin Description

Pin# Pin

Name Type Description

1 XIN/CLK I Connect to crystal or clock.

2 XOUT O Crystal output.

3 DIV2 I

Digital logic input used to select normal output mode or divide-by-two output mode.

When this pin is HIGH, the frequency of the output clock is the same as the input

clock frequency. When it is tied low, the output frequency is half the input clock

frequency. This pin has an internal pull-up resistor.

4 VSS P Ground to entire chip. Connect to system ground.

5 SR0 I

Digital logic input used to select Spreading Range Refer Modulation Output and

Spreading Range Selection Table. This pin has an internal pull-up resistor.

6 SSON# I

Digital logic input used to enable Spread Spectrum function (Active LOW). Spread

Spectrum function enabled when LOW, disabled when HIGH. This pin has an internal

pull-low resistor.

7 ModOUT O Spread spectrum clock output.

8 VDD P Power supply for the entire chip (+3.3V or 5.0V)

Output Frequency Selections

Input Frequency 8 MHz 12 MHz 16 MHz 20 MHz 24 MHz 28 MHz 32 MHz

0 (1/2 X) 4 MHz 6 MHz 8 MHz 10 MHz 12 MHz 14 MHz 16 MHz

DIV2 1 (1X) 8 MHz 12 MHz 16 MHz 20 MHz 24 MHz 28 MHz 32 MHz

Output

Frequency

Frequency Deviation Selections as a Function of Input Frequency

Input Frequency Range

P/N SR0 8 MHz 12 MHz 16 MHz 20 MHz 24 MHz 28 MHz 32 MHz Modulation

Rate (KHz)

0 ± 3.0% ± 2.5% ± 2.0% ± 1.8% ± 1.5% ± 1.5% ± 1.3%

P2005A 1 ± 2.5% ± 2.0% ± 1.8% ± 1.5% ± 1.3% ± 1.3% ± 1.0%

0 ± 1.8% ± 1.5% ± 1.2% ± 1.1% ± 0.9% ± 0.9% ± 0.8%

P2005S

1 ± 1.5% ± 1.2% ± 1.1% ± 0.9% ± 0.8% ± 0.8% ± 0.6%

(XIN/20) * 62.5

October 2003 P2005X

rev 1.0

General purpose EMI Reduction IC 3 of 10

Notice: The information in this document is subject to change without notice.

Spread Spectrum

The Output Frequency Selection Table and the Frequency Deviations Selections Table illustrate the two

possible spread spectrum options. The optimal setting should minimize system EMI to the fullest without

affecting system performance. The spreading is described as a percentage deviation of the center frequency

(Note: The center frequency is the frequency of the external reference input on CLKIN, Pin1).

Example:

The P2005X is designed for communications, digital video and imaging applications. It is not only optimized for

operation in the 8MHz – 32MHz range, but its output frequency can be extended down to one half of the input

clock frequency using the divide-by-two feature. This feature extends low frequency as low as to 4MHz. Setting

Pin 3 low (DIV2 = 0; Divide-by-two mode) sets the output frequency (ModOUT) to half the frequency of the input

clock (CLKIN). This is a simple way to generate a spread spectrum modulated low frequency clock when only a

higher frequency signal is available. If you want the output frequency to be the same as the input, you can either

set DIV2=1 or leave it unconnected.

Selecting the P2005X’s spread options is a matter of either setting SR0=1 or SR0=0. Setting SR0=0 set as a

lower modulation spread, while setting it to 1 introduces a wider spectral spread in the output clock. Refer

Modulation output and Spreading Selections Tables. The example given in the figure below shows the device

set to the divide-by-two mode (DIV2=0) with a lower spectrum range (SR0=0). The versatility provided by

allowing both clock division and spread spectrum on one chip is already proving to be a popular solution among

leading system manufacturers.

P2005X Application Schematic

CLKIN

XOUT

DIV2

VSS

MODOUT

SR0

SSON#

VDD

8.832MHz Cr

stal

Modulated 4.416MHz is

connected to CLK input

pin of the system

+3.3V

0.1µF

P2005X

October 2003 P2005X

rev 1.0

General purpose EMI Reduction IC 4 of 10

Notice: The information in this document is subject to change without notice.

EMC Software Simulation

By using Alliance’s proprietary EMC simulation software – EMI-Lator®, radiated system level EMI analysis can

be made easier, allowing quantitative measure on the benefits of Alliance’s EMI reduction products. The

simulation engine of this EMC software has already been characterized to correlate with the electrical

characteristics of Alliance EMI reduction ICs. The figure below is an illustration of this simulation result.

Please visit our website at www.alsc.com for information on how to obtain a free copy and demonstration of

EMI-Lator ®.

Simulation results From EMI-Lator®

October 2003 P2005X

rev 1.0

General purpose EMI Reduction IC 5 of 10

Notice: The information in this document is subject to change without notice.

Absolute Maximum Ratings

Symbol Parameter Rating Unit

VDD, VIN Voltage on any pin with respect to GND -0.5 to + 7.0 V

TSTG Storage temperature -65 to +125 °C

TA Operating temperature 0 to 70 °C

Note: These are stress ratings only and functional operation is not implied. Exposure to absolute maximum

ratings for extended periods may affect device reliability.

DC Electrical Characteris tics

Symbol Parameter Min Typ Max Unit

VIL Input low voltage GND – 0.3 - 0.8 V

VIH Input high voltage 2.0 - VDD + 0.3 V

IIL Input low current (pull-up resistors on inputs SR0, SR1,

CP0 and CP1) - - -35 µA

IIH Input high current (pull-down resistor on input SSON#) - - 35 µA

IXOL XOUT Output Low Current (@ 0.4V, VDD = 3.3V) - 3 - mA

IXOH XOUT Output High Current (@ 2.5V, VDD = 3.3V) 3

VOL Output low voltage (VDD = 3.3V, IOL = 20mA) - - 0.4 V

VOH Output high voltage (VDD = 3.3V, IOH = 20mA) 2.5 - - V

ICC Dynamic supply current normal mode (3.3V, and 15pF

loading) 6.0 7.0 8.3 mA

IDD Static supply current standby mode - 0.6 - mA

VDD Operating voltage 3.1 3.3 5.5 V

tON Power up time (first locked clock cycle after power up) - 0.18 - mS

ZOUT Clock output impedance - 50 - Ω

October 2003 P2005X

rev 1.0

General purpose EMI Reduction IC 6 of 10

Notice: The information in this document is subject to change without notice.

AC Electrical Characteris tics

Symbol Parameter Min Typ Max Unit

fIN Input frequency 8 - 32 MHz

fOUT Output frequency 4 - 32 MHz

tLH* Output rise time (measured at 0.8V to 2.0V) 0.7 0.9 1.1 ns

tHL* Output fall time (measured at 2.0V to 0.8V) 0.6 0.8 1.0 ns

tJC Jitter (cycle to cycle) - - 360 ps

tD Output duty cycle 45 50 55 %

*tLH and tHL are measured into a capacitive load of 15pF

October 2003 P2005X

rev 1.0

General purpose EMI Reduction IC 7 of 10

Notice: The information in this document is subject to change without notice.

Package Information

8-Pin SOIC

Symbol Dimensions in inches Dimensions in millimeters

Min Max Min Max

A 0.057 0.071 1.45 1.80

A1 0.004 0.010 0.10 0.25

A2 0.053 0.069 1.35 1.75

B 0.012 0.020 0.31 0.51

C 0.004 0.01 0.10 0.25

D 0.186 0.202 4.72 5.12

E 0.148 0.164 3.75 4.15

e 0.050 BSC 1.27 BSC

H 0.224 0.248 5.70 6.30

L 0.012 0.028 0.30 0.70

θ 0° 8° 0° 8°

October 2003 P2005X

rev 1.0

General purpose EMI Reduction IC 8 of 10

Notice: The information in this document is subject to change without notice.

8-Pin TSSOP

Dimensions in inches Dimensions in millimeters

Symbol Min Max Min Max

A 0.047

1.10

A1 0.002 0.006 0.05 0.15

A2 0.031 0.041 0.80 1.05

B 0.007 0.012 0.19 0.30

C 0.004 0.008 0.09 0.20

D 0.114 0.122 2.90 3.10

E 0.169 0.177 4.30 4.50

e 0.026 BSC 0.65 BSC

H 0.244 0.260 6.20 6.60

L 0.018 0.030 0.45 0.75

θ 0° 8° 0° 8°

October 2003 P2005X

rev 1.0

General purpose EMI Reduction IC 9 of 10

Notice: The information in this document is subject to change without notice.

Ordering Codes

Part Number Marking Package type Qty/reel Temperature

P2005X-08ST P2005X 8 PIN SOIC, TUBE 0°C To 70°C

P2005X-08SR P2005X 8-PIN SOIC, TAPE AND REEL 2,500 0°C To 70°C

P2005X-08TT P2005X 8-PIN TSSOP, TUBE 0°C To 70°C

P2005X-08TR P2005X 8-PIN TSSOP, TAPE AND REEL 2,500 0°C To 70°C

October 2003 P2005X

rev 1.0

General purpose EMI Reduction IC 10 of 10

Notice: The information in this document is subject to change without notice.

Licensed under U.S Patent Nos 5,488,627 and 5,631,921

trademarks or registered trademarks of Alliance. All other brand and product names may be the trademarks of their

respective companies. Alliance reserves the right to make changes to this document and its products at any time without

notice. Alliance assumes no responsibility for any errors that may appear in this document. The data contained herein

represents Alliance's best data and/or estimates at the time of issuance. Alliance reserves the right to change or correct this

data at any time, without notice. If the product described herein is under development, significant changes to these

specifications are possible. The information in this product data sheet is intended to be general descriptive information for

potential customers and users, and is not intended to operate as, or provide, any guarantee or warrantee to any user or

customer. Alliance does not assume any responsibility or liability arising out of the application or use of any product

described herein, and disclaims any express or implied warranties related to the sale and/or use of Alliance products

including liability or warranties related to fitness for a particular purpose, merchantability, or infringement of any intellectual

property rights, except as express agreed to in Alliance's Terms and Conditions of Sale (which are available from Alliance).

All sales of Alliance products are made exclusively according to Alliance's Terms and Conditions of Sale. The purchase of

products from Alliance does not convey a license under any patent rights, copyrights; mask works rights, trademarks, or any

other intellectual property rights of Alliance or third parties. Alliance does not authorize its products for use as critical

components in life-supporting systems where a malfunction or failure may reasonably be expected to result in significant

injury to the user, and the inclusion of Alliance products in such life-supporting systems implies that the manufacturer

assumes all risk of such use and agrees to indemnify Alliance against all claims arising from such use.

Alliance Semiconductor Corporation

2595, Augustine Drive,

Santa Clara, CA 95054

Tel# 408-855-4900

Fax: 408-855-4999

www.alsc.com

Preliminary Information

Part Number: P2005X

Document Version: v1.0