Resistors Cylindrical High Power Surface Mount Metal GlazeTM CHP Metal GlazeTM thick film element fired at 1000C to solid ceramic Cylindrical High Power CHP Series Surface Mount Metal GlazeTM Up to 2 watts Up to 1000 volts 0.2 ohm to 2.2 megohm range * Up to 2 watts RoHS-compliant version available * Up to 1000 volts 150C maximum operating * 0.2 ohm to 2.2 megohm range temperature * RoHS-compliant AEC-Q200 version available * 150C maximum operating temperature OBSOLETE Metal GlazeTM thick film element fired at 1000C to solid ceramic High temperature dielectric coating Solder over High nickel barrier temperature All Pb-free parts comply with EU dielectric coating Solder over Directive 2011/65/EU amended by (EU) 2015/863 (RoHS3) nickel barrier Electrical Data IRC Type Industry Footprint CHP 1/8 CHP 1/2 CHP 1 CHP 2 1206 2010 Size Code1 Maximum Power Rating B&C 1/4W @ 70C D&E 2512 3610 1/2W @ 70C F H Working Voltage 1W @ 70C 2W @ 25C 1.33W @ 70C Maximum Voltage 200 300 350 500 Resistance Range (ohms) Product Category Tolerance (%) TCR (ppm/C) 0.1 to 0.99 Low Range 1, 2, 5 100 400 600 700 1000 See pages 2 & 3 for product dimensions, recommended solder pads, and standard packaging. 1.0 to 1.0 M Standard 1, 2, 5 50, 100 20 to 348K Tight Tolerance 0.25, 0.5 50, 100 0.1 to 0.99 Low Range 1, 2, 5 100 50, 100 1.0 to 348K Standard 1, 2, 5 0.1 to 0.99 Low Range 1, 2, 5 100 1.0 to 2.21M Standard 1, 2, 5 50, 100 20 to 348K Tight Tolerance 0.25, 0.5 50, 100 0.2 to 0.99 Low Range 1, 2, 5 100 1.0 to 2.21M Standard 1, 2, 5 50, 100 Not to exceed P x R Consult factory for tighter TCR, tolerance, or resistance values. Environmental Data Characteristics Characteristics Maximum MaximumChange Change Thermal Shock Temperature Coefficient 0.25% +.01 As specified MIL-PRF-55342H, 4.8.3 MIL-R-55342H ParMethod 3.16 (-55C 125C) / -65C) (MIL-STD-202, 107G:+ +150C Thermal Shock Operation Low Temperature 0.5% + 0.01 0.25% +.01ohm MIL-R-55342H Par 3.9 (-65C + 150C, 5 cycles) Low Temperature Operation 0.25% 0.01ohm 0.5%++.01 MIL-R-55342H Par 3.11 (-65C @ working voltage) Short Time Overload 0.5% + 0.01 ohm 1% for R>100K ohm MIL-R-55342H Par 3.12 MIL-PRF-55342H, 4.8.7 2.5 x P x R for 5 seconds High Temperature Exposure 0.5% + 0.01 ohm MIL-R-55342H Par 3.13 (-150C for 100 hours) Resistance to Bonding Moisture Resistance 0.25% + 0.01 ohm MIL-R-55342H Par 3.14.2 (Reflow soldered to board at 260C for 10 seconds) MIL-PRF-55342H, 4.8.8.2 Exposure 95% minimum coverage MIL-STD-202, Method 208 (245C for 5 seconds) Solderability 0.5% + 0.01 ohm MIL-R-55342H Par 3.18 (10 cycles, total 240 hours) Short Time Overload High Temperature Exposure Resistance to Bonding Exposure Temperature Coefficient Life Test 1% for R>100K 0.5% +.01 0.25% +.01 0.5% +.01 As specified 1% +.01 Test Method Test Method MIL-PRF-55342H, 4.8.5 (-65C) MIL-PRF-55342H, 4.8.6 (150C x 100 Hours) MIL-PRF-55342H, 4.8.8.2 (MIL-STD-202, Method 106G) MIL-PRF-55342H, 4.8.10 (MIL-STD-202, Method 304) MIL-PRF-55342H, 4.8.11 Moisture Resistance 0.5% + 0.01 ohm (MIL-STD-202, 108A: 2000 Hoursintermittent) @ 70C) MIL-R-55342H ParMethod 3.15 (2000 hours at 70C Solderability Life Test 95%+ minimum 1% 0.01 ohm coverage no mechanical damage 1200 gram push from underside (MIL-STD-202, Method 208H)of mounted chip for 60 seconds no mechanical damage exert pull on chip contacts for 5 seconds Terminal Adhesion Strength MIL-PRF-55342H, 4.8.12 1% +.01 IRC - defined Terminal Adhesion Strength (push) 1% + 0.01 ohm Chip mounted in center of 90mm long board, deflected 1mm so as to (no mechanical damage) 1200 gram push from underside of mounted device for 60 sec 1% +.01 General Note Terminal Adhesion Strength (flex) IRC reserves the right to make changes in product specification(no withoutmechanical notice or liability. damage) All information is subject to IRC's own data and is considered accurate at time of going to print. IRC-defined Device mounted in center of 90mm long board, deflected 1 mm to exert pull on contacts for 5 seconds (c) IRC Wire and Film Technologies Division * 4222 South Staples Street * Corpus Christi Texas 78411 USA General Note Telephone: 361 992 7900 * Facsimile: 361 992 3377 * Website: www.irctt.com TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics' own data and is considered accurate at time of going to print. A subsidiary of TT electronics plc CHP Series Issue MarchWelwyn 2011 Sheet 1 of 3 BI Technologies IRC www.ttelectronics.com/resistors (c) TT Electronics plc 03.19 CHP Cylindrical High Power Surface Mount Metal GlazeTM Cylindrical High Power OBSOLETE Surface Mount Metal GlazeTM CHP Series Physical Data L C W Dimensions (Inches and (mm)) IRC Type Size Code Industry Footprint CHP 1/8 B 1206 0.128 0.007 (3.25 0.18) CHP 1/2 D 2010 0.200 0.010 0.079 (nom.) -0.006 / +0.011 (2.01 (nom.) -0.15 / +0.28) (5.08 0.25) 0.030 0.010 (0.761 0.25) CHP 1 F 2512 0.251 0.010 (6.38 0.25) 0.079 (nom.) -0.006 / +0.011 (2.01 (nom.) -0.15 / +0.28) 0.040 0.010 (1.02 0.25) CHP 2 H 3610 0.367 0.010 0.105 (nom.) -0.006 / +0.011 (2.67 (nom.) -0.15 / +0.28) (9.32 0.25) 0.050 0.010 (1.27 0.25) Actual Size L W C 0.057 0.006 (1.45 0.15) 0.020 0.010 (0.51 0.25) Recommended Solder Pad Dimensions (Reflow): F A C A B E D Size Code Industry Footprint B&C Dimensions (Inches and mm)) A B C D E F 1206 0.076 (1.93) 0.093 (2.36) 0.058 (1.47) 0.098 (2.49) 0.032 (0.81) 0.211 (5.36) D 2010 0.111 (2.82) 0.126 (3.20) 0.096 (2.44) 0.152 (3.86) 0.040 (1.02) 0.318 (8.08) E 2010 0.170 (4.32) 0.160 (4.06) 0.072 (1.83) 0.132 (3.35) 0.044 (1.12) 0.412 (10.46) F 2512 0.121 (3.07) 0.126 (3.20) 0.127 (3.23) 0.183 (4.65) 0.040 (1.02) 0.369 (9.37) H 3610 0.170 (4.32) 0.160 (4.06) 0.213 (5.41) 0.273 (6.93) 0.044 (1.12) 0.553 (14.05) (c) IRC Wire and Film Technologies Division * 4222 South Staples Street * Corpus Christi Texas 78411 USA Telephone: 361 992 7900 * Facsimile: 361 992 3377 * Website: www.irctt.com General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics' own data and is considered accurate at time of going to print. CHP Series Issue March 2011 Sheet 2 of 3 BI Technologies IRC Welwyn www.ttelectronics.com/resistors (c) TT Electronics plc 03.19 CHP Cylindrical High Power Surface Mount Metal GlazeTM Cylindrical High Power OBSOLETE Surface Mount Metal GlazeTM CHP Series Standard Reel Packaging per EIA-481: IRC Type Size Code Industry Footprint CHP 1/8 MRC 1/2 B C 1206 CHP 1/2 MRC 1 D E 2010 CHP 1 F 2512 CHP 2 H 3610 Reel Diameter* Quantity Per Reel 7 2,500 max. 13 10,000 max. 7 1,500 max. 13 5,000 max. 7 1,500 max. 13 5,000 max. 13 1,500 max. Carrier Tape Width Component Pitch 8mm 4mm 12mm 4mm 12mm 4mm 24mm 4mm *The 13 reel is considered standard and will be supplied unless otherwise specified. Repetitive Surge Curve Power Derating Curve 100 1000 80 Peak Power (watts) % of Rated Power CHP 1/8, 1/2, 1 60 CHP 2 40 20 0 30 40 50 60 70 80 CHP 2 CHP 1 100 10 CHP 1/8 CHP 1/2 90 100 110 120 130 140 150 1 0.0001 Ambient Temperature (C) .1msec 0.0010 1msec 0.0100 10msec 0.1000 100msec 1.0000 10000msec Surge or Pulse Duration (seconds) Note: Use for repetitive pulses where the average power dissipation is not to exceed the component rating at 70C. Surge handling capacity for low-repetitive surges may be significantly greater than shown above. Contact factory for recommendations. Ordering Data Sample Part No. CHP 1 - 100 2203 F 13 LF IRC Type (CHP 1/8, CHP 1/2, CHP 1, or CHP 2) Temperature Coefficient (50 ppm, 100 ppm) Resistance Value (100 ohms and greater - First 3 significant digits plus 4th digit multiplier) Example: 100 ohms = 1000, 1000 ohms = 1001, 150,000 ohms = 1503 (Less than 100 ohms - "R" is used to designate decimal) Example: 51 ohms = 51R0, 1 ohm = 1R00, 0.25 ohms = R250 Tolerance (C = 0.25%, D = 0.5%, F = 1.0%; G = 2.0%; J = 5.0%) Packaging Code* (BLK = Bulk, 7 = 7" Reel, 13 = 13" Reel) Lead Free Construction (c) IRC Wire and Film Technologies Division * 4222 South Staples Street * Corpus Christi Texas 78411 USA Telephone: 361 992 7900 * Facsimile: 361 992 3377 * Website: www.irctt.com General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics' own data and is considered accurate at time of going to print. CHP Series Issue March 2011 Sheet 3 of 3 BI Technologies IRC Welwyn www.ttelectronics.com/resistors (c) TT Electronics plc 03.19 Cylindrical High Power Surface Mount Metal GlazeTM OBSOLETE CHP Series Ordering Procedure This product has two valid part numbers: European (Welwyn) Part Number: CHP1-220KFI (CHP1 with TCR 100ppm/C at 220 kilohms 1%, Pbfree) C H P 1 - 1 2 2 2 0 K 3 F I 4 5 1 2 3 4 5 Type TCR (ppm/C) Value Tolerance CHP1/8 CHP1/2 CHP1 CHP2 Omit for 100 -50 = 50 E24 = 3/4 characters C = 0.25% E96 = 4/5 characters D = 0.5% F = 1% R = ohms K = kilohms G = 2% M = megohms J = 5% Termination & Packing I = Pb-free, standard pack PB = SnPb, standard pack CHP1/8 2500/7" reel Tape CHP1/2, 1 1500/7" reel CHP2 1500/13" reel T5 = Pb-free, 5K pack option CHP1/8, 1/2 & 1 Tape 5000/13" reel USA (IRC) Part Number: CHP11002203FLF (CHP1 with TCR 100ppm/C at 220 kilohms 1%, Pb-free) C H P 1 1 1 0 0 2 2 2 0 3 3 F L 4 F 5 1 2 3 4 5 Type TCR Value Tolerance Termination & Packing CHP1/8 CHP1/2 CHP1 CHP2 50 = 50 3 digits + multiplier C = 0.25% Omit for SnPb, Standard pack 100 = 100 D = 0.5% LF = Pb-free, Standard pack R = ohms for values <100 ohms F = 1% CHP1/8 2500/7" reel G = 2% CHP1/2 & 1 1500/7" reel CHP2 1500/13" reel J = 5% General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics' own data and is considered accurate at time of going to print. BI Technologies IRC Welwyn www.ttelectronics.com/resistors (c) TT Electronics plc 03.19