TVS Diodes Surface Mount - 600W > SMA6J series SMA6J Series Pb e3 RoHS Uni-directional Description The SMA6J series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Bi-directional Features Agency Approvals AGENCY AGENCY FILE NUMBER E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit PPPM 600 W Power Dissipation on Infinite Heat Sink at TL=50OC PD 3.3 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 60 A Maximum Instantaneous Forward Voltage at 25A for Unidirectional Only VF 3.5 V Operating Temperature Range TJ -65 to 150 C Storage Temperature Range TSTG -65 to 175 C Typical Thermal Resistance Junction to Lead RJL 30 C/W Typical Thermal Resistance Junction to Ambient RJA 120 C/W Peak Pulse Power Dissipation by 10/1000s Waveform (Fig.2) (Note 1), (Note 2) Notes: 1. Non-repetitive current pulse, per Fig.4 and derated above TJ (initial) =25C per Fig. 3. 2. Mounted on 5.0x5.0mm copper pad to each terminal. * Small DO-214AC SMT footprint for minimal board space requirement * Typical failure mode is a short circuit condition for current events exceeding component rating * Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c * IEC 61000-4-2 ESD 30kV(Air), 30kV (Contact) * ESD protection of data lines in accordance with IEC 61000-4-2 * Built-in strain relief * Glass passivated junction * Low inductance * Excellent clamping capability * 600W peak pulsepower capability at 10/1000s waveform, repetition rate (duty cycle): 0.01% *F ast response time: typically less than 1.0ps from 0 Volts to VBR min * Typical IR < 1A when VBR min > 12 V * High temperature reflow soldering guaranteed: 260C/40sec * VBR @ TJ= VBR@25C x (1+T x (TJ - 25)) (T:Temperature Coefficient, typical value is 0.1%) * UL Recognized compound meeting flammability rating V-0 * Meet MSL level1, per J-STD-020, lead-frame maximun peak of 260C * Matte tin lead-free plated * Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/ JEDEC J-STD-609A.01) Applications TVS components are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Functional Diagram 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional component only. Bi-directional Cathode Anode Uni-directional (c) 2018 Littelfuse, Inc. Revised: 05/08/18 Specifications are subject to change without notice. littelfuse.com TVS Diodes Surface Mount - 600W > SMA6J series Electrical Characteristics (T =25C unless otherwise noted) A Maximum Clamping Voltage VC @ Ipp (V) Maximum Peak Pulse Current Ipp (A) Maximum Reverse Leakage IR @ VR (A) Agency Recognition 10 9.2 66.0 800 X 10 10.3 61.0 800 X 10 11.2 56.0 500 X 8.60 10 12.0 50.0 200 X 8.33 9.21 1 12.9 46.5 100 X 8 8.89 9.83 1 13.6 44.1 50 X 6WT 8.5 9.44 10.40 1 14.4 41.7 20 X 6AV 6WV 9 10.0 11.1 1 15.4 39.0 10 X SMA6J10CA 6AX 6WX 10 11.1 12.3 1 17.0 37.0 5 X SMA6J11CA 6AZ 6WZ 11 12.2 13.5 1 18.2 33.0 1 X X Reverse Stand off Voltage VR (Volts) Breakdown Voltage VBR (Volts) @ IT Part Number (Uni) Part Number (Bi) UNI BI MIN MAX SMA6J5.0A SMA6J5.0CA 6BA 6WE 5 6.40 7.00 SMA6J6.0A SMA6J6.0CA 6AG 6WG 6 6.67 7.37 SMA6J6.5A SMA6J6.5CA 6AK 6WK 6.5 7.22 7.98 SMA6J7.0A SMA6J7.0CA 6AM 6WM 7 7.78 SMA6J7.5A SMA6J7.5CA 6AP 6WP 7.5 SMA6J8.0A SMA6J8.0CA 6AR 6WR SMA6J8.5A SMA6J8.5CA 6AT SMA6J9.0A SMA6J9.0CA SMA6J10A SMA6J11A Marking Test Current IT (mA) SMA6J12A SMA6J12CA 6BE 6XE 12 13.3 14.7 1 19.9 31.0 1 SMA6J13A SMA6J13CA 6BG 6XG 13 14.4 15.9 1 21.5 29.0 1 X SMA6J14A SMA6J14CA 6BK 6XK 14 15.6 17.2 1 23.2 25.8 1 X SMA6J15A SMA6J15CA 6BM 6XM 15 16.7 18.5 1 24.4 25.1 1 X SMA6J16A SMA6J16CA 6BP 6XP 16 17.8 19.7 1 26.0 23.1 1 X SMA6J17A SMA6J17CA 6BR 6XR 17 18.9 20.9 1 27.6 22.6 1 X SMA6J18A SMA6J18CA 6BT 6XT 18 20.0 22.1 1 29.2 21.5 1 X SMA6J20A SMA6J20CA 6BV 6XV 20 22.2 24.5 1 32.4 19.4 1 X SMA6J22A SMA6J22CA 6BX 6XX 22 24.4 26.9 1 35.5 17.0 1 X SMA6J24A SMA6J24CA 6BZ 6XZ 24 26.7 29.5 1 38.9 16.0 1 X SMA6J26A SMA6J26CA 6CE 6YE 26 28.9 31.9 1 42.1 14.9 1 X SMA6J28A SMA6J28CA 6CG 6YG 28 31.1 34.4 1 45.4 13.8 1 X SMA6J30A SMA6J30CA 6CK 6YK 30 33.3 36.8 1 48.4 12.5 1 X SMA6J33A SMA6J33CA 6CM 6YM 33 36.7 40.6 1 53.3 11.8 1 X SMA6J36A SMA6J36CA 6CP 6YP 36 40.0 44.2 1 58.1 10.4 1 X SMA6J40A SMA6J40CA 6CR 6YR 40 44.4 49.1 1 64.5 9.7 1 X SMA6J43A SMA6J43CA 6CT 6YT 43 47.8 52.8 1 69.4 8.7 1 X SMA6J45A SMA6J45CA 6CV 6YV 45 50.0 55.3 1 72.7 8.3 1 X SMA6J48A SMA6J48CA 6CX 6YX 48 53.3 58.9 1 77.4 8.1 1 X SMA6J51A SMA6J51CA 6CZ 6YZ 51 56.7 62.7 1 82.4 7.4 1 X SMA6J54A SMA6J54CA 6RE 6ZE 54 60.0 66.3 1 87.1 6.9 1 X SMA6J58A SMA6J58CA 6RG 6ZG 58 64.4 71.2 1 93.6 6.7 1 X SMA6J60A SMA6J60CA 6RK 6ZK 60 66.7 73.7 1 96.8 6.2 1 X SMA6J64A SMA6J64CA 6RM 6ZM 64 71.1 78.6 1 103 5.9 1 X SMA6J70A SMA6J70CA 6RP 6ZP 70 77.8 86.0 1 113 5.5 1 X SMA6J75A SMA6J75CA 6RR 6ZR 75 83.3 92.1 1 121 5.0 1 X SMA6J78A SMA6J78CA 6RT 6ZT 78 86.7 95.8 1 126 4.8 1 X SMA6J85A SMA6J85CA 6RV 6ZV 85 94.4 104 1 137 4.6 1 X X SMA6J90A SMA6J90CA 6RX 6ZX 90 100 111 1 146 4.2 1 SMA6J100A - 6RZ - 100 111 123 1 162 3.8 1 X SMA6J110A - 6SE - 110 122 135 1 177 3.5 1 X SMA6J120A - 6SG - 120 133 147 1 193 3.2 1 X SMA6J130A - 6SK - 130 144 159 1 209 2.9 1 X For bidirectional type having VR of 10 volts and less, the IR limit is double. (c) 2018 Littelfuse, Inc. Revised: 05/08/18 Specifications are subject to change without notice. littelfuse.com TVS Diodes Surface Mount - 600W > SMA6J series I-V Curve Characteristics Uni-directional I I Bi-directional Ipp Vc VBR VR Vc VBR VR V IR VF IT IR IT VR VBR Vc V Ipp Ipp PPPM VR VBR VC IR VF IT IR Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the TVS at a specified IPPM (peak impulse current @ 10/1000) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Curve 100 PPPM-Peak Pulse Power (kW) Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS 10 1 0.2x0.2" (5.0x5.0mm) Copper Pad Area 0.1 Time 0.001 0.01 0.1 1 td-Pulse Width (ms.) continues on next page. (c) 2018 Littelfuse, Inc. Revised: 05/08/18 Specifications are subject to change without notice. littelfuse.com TVS Diodes Surface Mount - 600W > SMA6J series Ratings and Characteristic Curves (T =25C unless otherwise noted) (Continued) A Figure 3 - Peak Pulse Power Derating Curve Figure 4 - Pulse Waveform 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 100 80 60 40 20 0 0 25 50 75 100 125 150 TJ - Initial Junction Temperature (C) TJ=25C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Peak Value IPPM 100 Half Value IPPM IPPM ( ) 2 50 0 175 10/1000sec. Waveform as defined by R.E.A td 0 1.0 2.0 3.0 4.0 t-Time (ms) Figure 6 - Peak Forward Voltage Drop vs Peak Forward Current (typical values) Figure 5 - Typical Transient Thermal Impedance 1000 100 100 I F - Peak Forward Current(A) Transient Thermal Impedance ( C/W) tr=10sec 10 1 0.1 0.001 0.01 0.1 1 10 100 1000 TP - Pulse Duration (s) 10 1 0.1 0.01 0 1 2 3 4 5 VF - Peak Forward Voltage(V) Figure 7 - Maximum Non-Repetitive Forward Surge Current Uni-Directional Only IFSM - Peak Forward Surve Current(A) 80 70 60 50 40 30 20 10 0 1 10 100 Number of Cycles at 60 Hz (c) 2018 Littelfuse, Inc. Revised: 05/08/18 Specifications are subject to change without notice. littelfuse.com 6 TVS Diodes Surface Mount - 600W > SMA6J series Soldering Parameters Pre Heat Lead-free assembly - Temperature Min (Ts(min)) 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 180 secs Average ramp up rate (Liquidus Temp (TA) to peak 3C/second max TS(max) to TA - Ramp-up Rate 3C/second max Reflow - Temperature (TA) (Liquidus) 217C - Time (min to max) (ts) 60 - 150 seconds Peak Temperature (TP) 260+0/-5 C Time within 5C of actual peak Temperature (tp) 20 - 40 seconds Ramp-down Rate 6C/second max Time 25C to peak Temperature (TP) 8 minutes Max. Do not exceed 260C Physical Specifications Weight 0.002 ounce, 0.061 gram Case JEDEC DO-214AC Molded Plastic over glass passivated junction Polarity Color band denotes cathode except Bipolar Terminal Matte Tin-plated leads, Solderable per JESD22-B102 tp TP Ramp-up TL Temperature (T) Reflow Condition tL Critical Zone TL to TP Ts(max) Ramp-down Ts(min) ts Preheat 25C t 25C to Peak Time (t) Environmental Specifications High Temp. Storage JESD22-A103 HTRB JESD22-A108 Temperature Cycling JESD22-A104 MSL JEDEC-J-STD-020, Level 1 H3TRB JESD22-A101 RSH JESD22-A111 Dimensions DO-214AC (SMA) Dimensions Cathode Band C A B H D F E G J K L I Inches Millimeters Min Max Min Max A 0.049 0.065 1.250 1.650 B 0.157 0.181 3.990 4.600 C 0.095 0.110 2.400 2.790 D 0.075 0.090 1.900 2.290 E 0.030 0.060 0.780 1.520 F - 0.008 - 0.203 G 0.189 0.208 4.800 5.280 H 0.006 0.012 0.152 0.305 I 0.070 - 1.800 - J 0.082 - 2.100 - K - 0.090 - 2.300 L 0.082 - 2.100 - Solder Pads (all dimensions in mm) (c) 2018 Littelfuse, Inc. Revised: 05/08/18 Specifications are subject to change without notice. littelfuse.com TVS Diodes Surface Mount - 600W > SMA6J series Part Numbering System Part Marking System SMA6J xx C A 5% VBR VOLTAGE TOLERANCE Cathode Band F BI-DIRECTIONAL VR VOLTAGE Littelfuse Logo SERIES XX YMXXX Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code Packaging Component Package Part number SMA6JxxXX DO-214AC Quantity 5000 Packaging Option Tape & Reel - 12mm tape/13" reel Packaging Specification EIA RS-481 Tape and Reel Specification 0.157 (4.0) Cathode 0.47 (12.0) 0.157 (4.0) 0.059 DIA (1.5) Cover tape 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.49 (12.5) (c) 2018 Littelfuse, Inc. Revised: 05/08/18 Specifications are subject to change without notice. Dimensions are in inches (and millimeters). Direction of Feed littelfuse.com