VDE JE-X RELAYS COMPACT ECONOMICAL POWER RELAYS 22 .866 FEATURES 14 .551 * Compact size - Height Max. 18.7 mm .736 inch lower than JY relay (22.5 mm) (.886 inch) * High contact capacity -- 5A 125 V AC * Safety-oriented between coil and contact terminals * All plastic materials: UL flame retardance 94V-0 * VDE, TUV also approved 18.7 .736 mm inch TERMINAL LAYOUT Distance of 9.16 mm .360 inch between common and coil terminals and 8.9 mm .350 inch between contacts give room to the land diameter width when the relay is mounted on PC board, and allow design of patterns with insulation distances of 6 mm .236 inch between common and coil and 5.9 mm .232 inch between contacts. * 3 mm .118 inch or more insulation distance for close mounting can be kept easily with JE-X relays. 0.9 .035 R1 3 dia. .118 dia. Coil 9.16 .361 6.16 .243 8.9 .350 3 dia. .118 dia. N.O. 4.45 3 dia. .175 .118 dia. 5.9 .233 4.45 N.C. COM .175 In case of 3 mm .118 inch land diameter N.C. R2 3 .118 N.O. 8.9 .350 N.C. N.O. 1.3 dia. .051 dia. Coil mm inch mm inch SPECIFICATIONS Contact Arrangement Initial contact resistance, max. (By voltage drop 6 V DC 1A) Contact material Nominal switching capacity Rating Max. switching power (resistive load) Max. switching voltage Max. switching current Mechanical (at 180 cpm) Expected life (min. Electrical (at 20 cpm) operations) (at rated load) Characteristics 1 Form A 1 Form C 100 m Silver alloy 5 A 30 V DC, 5 A 125 V AC, 3A 250 V AC 750 VA, 150 W 250 V AC, 30 V DC 5A 5x106 105 Max. operating speed Initial insulation resistance*1 Between open contacts Between contacts and coil Surge voltage between coil and contact*3 Operate time*4 (at nominal voltage) Release time (without diode)*4 (at nominal voltage) Initial breakdown voltage*2 Temperature rise (at 70C) Coil Minimum operating power Nominal operating power 196 mW 400 mW Remarks * Specifications will vary with foreign standards certification ratings. *1 Measurement at same location as "Initial breakdown voltage" section *2 Detection current: 10 mA *3 Wave is standard shock voltage of 1.2 x 50s according to JEC-212-1981 *4 Excluding contact bounce time *5 Half-wave pulse of sine wave: 6ms; detection time: 10s *6 Half-wave pulse of sine wave: 6ms *7 Detection time: 10s *8 Refer to 6. Conditions for operation, transport and storage mentioned in AMBIENT ENVIRONMENT. Shock resistance Functional*5 Destructive*6 Functional*7 Vibration resistance Destructive Conditions for operation, Ambient transport and storage*8 temp. (Not freezing and condensHumidity ing at low temperature) Unit weight All Rights Reserved (c) COPYRIGHT Matsushita Electric Works, Ltd. 20 cpm (at 70C) Min. 100 M (at 500 V DC) 750 Vrms 1,500 Vrms Min. 5,000 V Approx. 10 ms Approx. 2 ms Max. 45C with nominal coil voltage and at nominal switching capacity Min. 98 m/s2 {10 G} Min. 980 m/s2 {100 G} 98 m/s2 {10 G}, 10 to 55 Hz at double amplitude of 1.6 mm 117.6 m/s2 {12 G}, 10 to 55 Hz at double amplitude of 2.0 mm -40C to +70C -40F to +158F 5 to 85% R.H. Approx. 9.2g .32 oz JE-X TYPICAL APPLICATIONS ORDERING INFORMATION Ex. JE * Home appliances Oven, range, dryer, heater, Air conditioner etc. * Automotive * Garage door opener * Personal computer * Programmable controller 1 X N DC12V Contact arrangement Pick-up voltage 1a: 1 Form A 1:1 Form C N:70% of nominal voltage H Protective construction Coil voltage DC 5, 6, 9, H: Flux-resistant type 12, 24, 48 V (Note) Standard packing: Carton 100 pcs. Case 500 pcs. UL/CSA, VDE approved type is standard. TYPES Contact arrangement Pick-up 70% V type Flux-resistant type JE1aXN-DC5V-H JE1aXN-DC6V-H JE1aXN-DC9V-H JE1aXN-DC12V-H JE1aXN-DC24V-H JE1aXN-DC48V-H JE1XN-DC5V-H JE1XN-DC6V-H JE1XN-DC9V-H JE1XN-DC12V-H JE1XN-DC24V-H JE1XN-DC48V-H Coil voltage 5 V DC 6 V DC 9 V DC 12 V DC 24 V DC 48 V DC 5 V DC 6 V DC 9 V DC 12 V DC 24 V DC 48 V DC 1 Form A 1 Form C COIL DATA (at 20C 68F) Nominal voltage, V DC Pick-up voltage, V DC (max.) Drop-out voltage, V DC (min.) 5 6 9 12 24 48 3.5 4.2 6.3 8.4 16.8 33.6 0.5 0.6 0.9 1.2 2.4 4.8 Nominal operating currrent, mA (10%) 80 67 44 33 17 8.3 Nominal operating power, mW 400 400 400 400 400 400 Coil resistance, (10%) 62.5 90 202 360 1,440 5,760 Maximum allowable voltage, V DC (at 70C) 6.5 7.8 11.7 15.6 31.2 62.4 DIMENSIONS mm inch PC board pattern (Bottom view) 14 .551 5-1.3 dia. 5-.051 dia. 22 .866 7.62 .300 4.45 .175 4.45 .175 10.16 .400 Tolerance: 0.1 .004 Max. 18.2 .717 Schematic (Bottom view) 0.5 .020 3.9 .154 0.8 .031 3.9 .154 1 10.16 .400 0.3 .012 7.62 .300 COM 3 2 1.1 .043 0.4 .016 7.62 .300 1 COM 3 0.8 .031 7.62 .300 N.O. 4 1.2 .047 N.C. 5 2 4.45 .175 4.45 .175 N.O. 4 5 N.C. Note: The above shows 1 Form C type, and No. 5 terminal is eliminated on the 1 Form A type. Dimension: Max. 1mm .039 inch: 1 to 5mm .039 to .197 inch: Min. 5mm .197 inch: All Rights Reserved (c) COPYRIGHT Matsushita Electric Works, Ltd. General tolerance 0.2 .008 0.3 .012 0.4 .016 JE-X REFERENCE DATA 1. Max. switching power 3. Coil temperature rise (at 30C 86F) 2. Operate and release time Operate & release time, ms Contact current, A 3 AC resistive load DC resistive load 1 0.5 10 Operate time Max. Min. 5 Release time 30 50 100 0 200250 80 100 Voltage, V 50 40 30 20 120 100 100 30C 40C 60C 50 Life, x104 60 125V AC resistive load 10 250V AC resistive load 40 30 100 110 130 150 Coil applied voltage, %V 1 0 1 2 3 4 5 110 130 150 Coil applied voltage, %V 5. Life curve 70 5A 3A 1.5A 0A 60 Coil applied voltage, %V 4. Coil temperature rise (Contact carrying current: 5 A) Temperature rise, C Max. Min. Temperature rise, C 15 5 6 Contact current, A NOTE Soldering should be carried out within 3 s at 350C 662F or within 5 s at 250C 482F. For Cautions for Use, see Relay Technical Information. All Rights Reserved (c) COPYRIGHT Matsushita Electric Works, Ltd.