Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC582LP5 / 582LP5E v03.0811 MMIC VCO w/ HALF FREQUENCY OUTPUT & DIVIDE-BY-4, 11.1 - 12.4 GHz Typical Applications Features Low noise MMIC VCO w/Half Frequency, Divide-by-4 Outputs for: Triple Output: Fo = 11.1 - 12.4 GHz Fo/2 = 5.55 - 6.2 GHz Fo/4 = 2.78 - 3.1 GHz * Point to Point/Multipoint Radio * Test Equipment & Industrial Controls Pout: +9 dBm Phase Noise: -110 dBc/Hz @100 kHz Typ. * SATCOM * Military End-Use No External Resonator Needed 32 Lead 5x5mm SMT Package: 25mm Functional Diagram The HMC582LP5 & HMC582LP5E are GaAs InGaP Heterojunction Bipolar Transistor (HBT) MMIC VCOs. The HMC582LP5 & HMC582LP5E integrate resonators, negative resistance devices, varactor diodes and feature half frequency and divide-by-4 outputs. The VCO's phase noise performance is excellent over temperature, shock, and process due to the oscillator's monolithic structure. Power output is +9 dBm typical from a +5V supply voltage. The prescaler and RF/2 functions can be disabled to conserve current if not required. The voltage controlled oscillator is packaged in a leadless QFN 5x5 mm surface mount package, and requires no external matching components. VCOS with Fo/2 OUTPUT - SMT 8 Electrical Specifications, TA = +25 C, Vcc (Dig), Vcc (Amp), Vcc (RF) = +5V Parameter Frequency Range Power Output Min. Fo Fo/2 RFOUT RFOUT/2 RFOUT/4 Tune Voltage Supply Current Typ. +5 +8 -9 -110 Vtune Icc(Dig) + Icc(Amp) + Icc(RF) 2 290 350 Output Return Loss 1/2 2nd 3rd Units GHz GHz +12 +14 -3 Tune Port Leakage Current (Vtune= 13V) Harmonics/Subharmonics Max. 11.1 - 12.4 5.55 - 6.2 SSB Phase Noise @ 100 kHz Offset, Vtune= +5V @ RFOUT Pulling (into a 2.0:1 VSWR) 8-1 General Description dBm dBm dBm dBc/Hz 12 V 390 mA 10 A 2 dB 32 25 30 dBc dBc dBc 5 MHz pp Pushing @ Vtune= 5V 30 MHz/V Frequency Drift Rate 1.2 MHz/C For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC582LP5 / 582LP5E v03.0811 MMIC VCO w/ HALF FREQUENCY OUTPUT & DIVIDE-BY-4, 11.1 - 12.4 GHz Frequency vs. Tuning Voltage, Vcc = +5V Frequency vs. Tuning Voltage, T= 25C 13.8 OUTPUT FREQUENCY (GHz) 12.8 12 +25C +85C -40C 11.2 10.4 13 12.2 11.4 Vcc= 4.75V Vcc= 5.00V Vcc= 5.25V 10.6 9.8 9.6 0 1 2 3 4 5 6 7 8 9 10 11 12 0 13 1 2 3 TUNING VOLTAGE (Volts) Sensitivity vs. Tuning Voltage, Vcc = +5V 6 7 8 9 10 11 12 13 16 8 14 OUTPUT POWER (dBm) 600 SENSITIVITY (MHz/Volt) 5 Output Power vs. Tuning Voltage, Vcc = +5V 700 +25C +85C -40C 500 400 300 200 100 12 10 8 6 4 +25C +85C -40C 2 0 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 0 1 2 3 TUNING VOLTAGE (Volts) 4 5 6 7 8 9 10 11 12 13 TUNING VOLTAGE (Volts) SSB Phase Noise vs. Tuning Voltage SSB Phase Noise @ Vtune = +5V -75 0 SSB PHASE NOISE (dBc/Hz) SSB PHASE NOISE (dBc/Hz) 4 TUNING VOLTAGE (Volts) -85 -95 10khz 100khz -105 -115 -125 0 1 2 3 4 5 6 7 8 9 TUNING VOLTAGE (VOLTS) 10 11 12 13 -30 +25C +85C -40C -60 -90 -120 -150 -180 2 10 3 10 4 10 5 10 6 10 VCOS with Fo/2 OUTPUT - SMT OUTPUT FREQUENCY (GHz) 13.6 7 10 TUNING VOLTAGE (VOLTS) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 8-2 HMC582LP5 / 582LP5E v03.0811 MMIC VCO w/ HALF FREQUENCY OUTPUT & DIVIDE-BY-4, 11.1 - 12.4 GHz RFOUT/2 Output Power vs. Tuning Voltage, Vcc = +5V 6.6 16 6.4 14 6.2 OUTPUT POWER (dBm) OUTPUT FREQUENCY (GHz) RFOUT/2 Frequency vs. Tuning Voltage, Vcc = +5V 6 5.8 5.6 5.4 +25C +85C -40C 5.2 6 +25C +85C -40C 4 1 2 3 4 5 6 7 8 9 10 11 12 13 0 1 2 3 4 5 6 7 8 9 TUNING VOTLAGE (Volts) TUNING VOLTAGE (Volts) Divide-by-4 Frequency vs. Tuning Voltage, Vcc = +5V Divide-by-4 Output Power vs. Tuning Voltage, Vcc = +5V 3.3 0 3.2 -1 3.1 -2 OUTPUT POWER (dBm) OUTPUT FREQUENCY (GHz) VCOS with Fo/2 OUTPUT - SMT 8 0 0 8-3 10 2 5 4.8 8 12 3 2.9 2.8 2.7 +25C +85C -40C 2.6 4 5 6 7 8 9 10 11 12 13 13 -7 -8 0 1 2 3 TUNING VOLTAGE (Volts) Absolute Maximum Ratings 11 12 -6 -9 3 10 -5 -10 2 13 -4 2.4 1 11 12 +25C +85C -40C -3 2.5 0 10 4 5 6 7 8 9 TUNING VOLTAGE (Volts) Typical Supply Current vs. Vcc Vcc(Dig), Vcc(Amp), Vcc(RF) +5.5 Vdc Vcc (V) Icc (mA) Vtune 0 to +15V 4.75 320 Junction Temperature 135 C 5.00 350 Continuous Pdiss (T=85 C) (derate 43.5 mW/C above 85 C 2.17 W 5.25 380 Thermal Resistance (junction to ground paddle) 23 C/W Storage Temperature -65 to +150 C Operating Temperature -40 to +85 C ESD Sensitivity (HBM) Class 1A Note: VCO will operate over full voltage range shown above. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC582LP5 / 582LP5E v03.0811 MMIC VCO w/ HALF FREQUENCY OUTPUT & DIVIDE-BY-4, 11.1 - 12.4 GHz Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 8 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. Package Information 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Part Number Package Body Material Lead Finish MSL Rating HMC582LP5 Low Stress Injection Molded Plastic Sn/Pb Solder MSL3 [1] HMC582LP5E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL3 [2] Package Marking [3] H582 XXXX H582 XXXX [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX Pin Descriptions Function Description 1 - 3, 8 - 10, 13 - 18, 20, 22 - 28, 30 - 32 Pin Number N/C No Connection. These pins may be connected to RF/ DC ground. Performance will not be affected. 4 RFOUT/4 Divide-by-4 output. DC block required. 6 Vcc (Dig) Supply voltage for prescaler. If prescaler is not required, this pin may be left open to conserve approximately 65 mA of current. Interface Schematic For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com VCOS with Fo/2 OUTPUT - SMT PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 8-4 HMC582LP5 / 582LP5E v03.0811 MMIC VCO w/ HALF FREQUENCY OUTPUT & DIVIDE-BY-4, 11.1 - 12.4 GHz Pin Descriptions VCOS with Fo/2 OUTPUT - SMT 8 8-5 Pin Number Function Description 7 Vcc (Amp) Supply voltage for RFOUT/2 output. If RFOUT/2 is not required, this pin may be left open to conserve approximately 30 mA of current. 12 RFOUT/2 Half frequency output (AC coupled). 19 RF OUT RF output (AC coupled). 21 Vcc (RF) Supply Voltage, +5V 29 VTUNE Control voltage and modulation input. Modulation bandwidth dependent on drive source impedance. See "Determining the FM Bandwidth of a Wideband Varactor Tuned VCO" application note. 5, 11, Paddle GND Package bottom has an exposed metal paddle that must be connected to RF/DC ground. Interface Schematic Typical Application Circuit For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC582LP5 / 582LP5E v03.0811 MMIC VCO w/ HALF FREQUENCY OUTPUT & DIVIDE-BY-4, 11.1 - 12.4 GHz Evaluation PCB List of Materials for Evaluation PCB 110227 [1] Item Description J1 - J4 PCB Mount SMA RF Connector J5 - J6 2 mm DC Header C1 - C3 100 pF Capacitor, 0402 Pkg. C4 1,000 pF Capacitor, 0402 Pkg. C5 - C7 2.2 F Tantalum Capacitor U1 HMC582LP5 / HMC582LP5E VCO PCB [2] 110225 Eval Board [1] Reference this number when ordering complete evaluation PCB The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and backside ground paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [2] Circuit Board Material: Rogers 4350 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com VCOS with Fo/2 OUTPUT - SMT 8 8-6 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: HMC582LP5E HMC582LP5 HMC582LP5ETR HMC582LP5TR 110227-HMC582LP5