F-PLA300-2 - COSEL - Product.Network

 2009-2012 Microchip Technology Inc. DS70616G-page 1

dsPIC33EPXXX(GP/MC/MU)806/810/814

and PIC24EPXXX(GP/GU)810/814

Operating Conditions

• 3.0V to 3.6V, -40ºC to +125ºC, DC to 60 MIPS

•3.0V to 3.6V, -40ºC to +85ºC, DC to 70 MIPS

Core: 16-Bit dsPIC33E/PIC24E CPU

• Code-Efficient (C and Assembly) architecture

• Two 40-Bit Wide Accumulators

• Single-Cycle (MAC/MPY) with Dual Data Fetch

• Single-Cycle Mixed-Sign MUL Plus Hardware Divide

• 32-Bit Multiply Support

Clock Management

• 2% Internal Oscillator

• Programmable PLLs and Oscillator Clock Sources

• Fail-Safe Clock Monitor (FSCM)

• Independent Watchdog Timer

• Fast Wake-up and Start-up

Power Management

• Low-Power Management modes (Sleep, Idle, Doze)

• Integrated Power-on Reset and Brown-out Reset

• 1.0 mA/MHz Dynamic Current (typical)

•60 µA I

PD Current (typical)

High-Speed PWM

• Up to Seven PWM Pairs with Independent Timing

• Dead Time for Rising and Falling Edges

• 8.32 ns PWM Resolution

• PWM Support for:

- DC/DC, AC/DC, Inverters, PFC, Lighting

- BLDC, PMSM, ACIM, SRM

• Programmable Fault Inputs

• Flexible Trigger Configurations for ADC Conversions

Advanced Analog Features

• Two Independent ADC modules:

- One ADC configurable as 10-bit, 1.1 Msps with four

S&H or 12-bit, 500 ksps with one S&H

- One 10-bit ADC, 1.1 Msps with four S&H

- Eight S&H using both ADC 10-bit modules

- 24 analog channels (64-pin devices) up to 32 analog

channels (100/121/144-pin devices)

• Flexible and Independent ADC Trigger Sources

• Comparators:

- Up to three Analog Comparator modules

- Programmable references with 32 voltage points

Timers/Output Compare/Input Capture

• 27 General Purpose Timers:

- Nine 16-bit and up to four 32-bit Timers/Counters

- 16 OC modules configurable as Timers/Counters

- Two 32-bit Quadrature Encoder Interface (QEI)

modules configurable as Timers/Counters

• 16 IC modules

• Peripheral Pin Select (PPS) to allow Function Remap

• Real-Time Clock and Calendar (RTCC) module

Communication Interfaces

• USB 2.0 OTG-Compliant Full-Speed Interface

• Four UART modules (15 Mbps)

- Supports LIN/J2602 protocols and IrDA®

• Four 4-Wire SPI modules (15 Mbps)

• Two ECAN™ modules (1 Mbaud) CAN 2.0B Support

•Two I

2C modules (up to 1 Mbaud) with SMBus Support

• Data Converter Interface (DCI) module with Support for

I2S and Audio Codecs

• PPS to allow Function Remap

• Parallel Master Port (PMP)

• Programmable Cyclic Redundancy Check (CRC)

Direct Memory Access (DMA)

• 15-Channel DMA with User-Selectable

Priority Arbitration

• UART, USB, SPI, ADC, ECAN™, IC, OC, Timers,

DCI/I2S, PMP

Input/Output

• Sink/Source 10 mA on All Pins

• 5V Tolerant Pins

• Selectable Open-Drain, Pull-ups and Pull-Downs

• Up to 5 mA Overvoltage Clamp Current

• External Interrupts on All I/O pins

Qualification and Class B Support

• AEC-Q100 REVG (Grade 1 -40ºC to +125ºC) Planned

• AEC-Q100 REVG (Grade 0 -40ºC to +150ºC) Planned

• Class B Safety Library, IEC 60730

Debugger Development Support

• In-Circuit and In-Application Programming

• Five Program and Three Complex Data Breakpoints

• IEEE 1149.2 Compatible (JTAG) Boundary Scan

• Trace and Run-Time Watch

16-Bit Microcontrollers and Digital Signal Controllers with

High-Speed PWM, USB and Advanced Analog

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 2  2009-2012 Microchip Technology Inc.

dsPIC33EPXXX(GP/MC/MU)806/810/814

and PIC24EPXXX(GP/GU)810/814

PRODUCT FAMILIES

The device names, pin counts, memory sizes and

peripheral availability of each device are listed in

Table 1. Their pinout diagrams appear on the following

pages.

TABLE 1: dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

CONTROLLER FAMILIES

Device

Pins

Packages

Program Flash Memory

(Kbyte)(1)

RAM (Kbyte)(2)

Remappable Peripherals

RTCC

I2C™

CRC Generator

10-Bit/12-Bit ADC(8)

USB

I/O Pins

16-Bit Timer(3,4)

Input Capture

Output Compare (with PWM)

Motor Control PWM

(Channels)(5)

QEI

UART with IrDA®

SPI

ECAN™

External Interrupts(6)

DMA Controller (Channels)

DCI

Analog Comparators/

Inputs Per Comparator(7)

Parallel Master Port

dsPIC33EP256MU806 64 QFN,

TQFP 280 28 9 16 16 8 2 4 4 2 5 15 1 3/4 1 2 1 2 ADC,

24 ch 1Y51

dsPIC33EP256MU810 100 TQFP 280 28 9 16 16 12 2 4 4 2 5 15 1 3/4 1 2 1 2 ADC,

32 ch 1Y83

121 TFBGA

dsPIC33EP256MU814 144 TQFP,

LQFP 280 28 9 16 16 14 2 4 4 2 5 15 1 3/4 1 2 1 2 ADC,

32 ch 1Y122

dsPIC33EP512GP806 64 QFN,

TQFP 536 52 9 16 16 — — 4 4 2 5 15 1 3/4 1 2 1 2 ADC,

24 ch —Y53

dsPIC33EP512MC806 64 QFN,

TQFP 536 52 9 16 16 8 2 4 4 2 5 15 1 3/4 1 2 1 2 ADC,

24 ch —Y53

dsPIC33EP512MU810 100 TQFP 536 52 9 16 16 12 2 4 4 2 5 15 1 3/4 1 2 1 2 ADC,

32 ch 1Y83

121 TFBGA

dsPIC33EP512MU814 144 TQFP,

LQFP 536 52 9 16 16 14 2 4 4 2 5 15 1 3/4 1 2 1 2 ADC,

32 ch 1Y122

PIC24EP256GU810 100 TQFP 280 28 9 16 16 0 0 4 4 2 5 15 1 3/4 1 2 1 2 ADC,

32 ch 1Y83

121 TFBGA

PIC24EP256GU814 144 TQFP,

LQFP 280 28 9 16 16 0 0 4 4 2 5 15 1 3/4 1 2 1 2 ADC,

32 ch 1Y122

PIC24EP512GP806 64 QFN,

TQFP 586 52 9 16 16 — — 4 4 2 5 15 1 3/4 1 2 1 2 ADC,

24 ch —Y53

PIC24EP512GU810 100 TQFP 536 52 9 16 16 0 0 4 4 2 5 15 1 3/4 1 2 1 2 ADC,

32 ch 1Y83

121 TFBGA

PIC24EP512GU814 144 TQFP,L

QFP 536 52 9 16 16 0 0 4 4 2 5 15 1 3/4 1 2 1 2 ADC,

32 ch 1Y122

Note 1: Flash size is inclusive of 24 Kbytes of auxiliary Flash. Auxiliary Flash supports simultaneous code execution and self-erase/programming.

Refer to Section 5. “Flash Programming” (DS70609) in the “dsPIC33E/PIC24E Family Reference Manual”.

2: RAM size is inclusive of 4 Kbytes of DMA RAM (DPSRAM) for all devices.

3: Up to eight of these timers can be combined into four 32-bit timers.

4: Eight out of nine timers are remappable.

5: PWM Faults and Sync signals are remappable.

6: Four out of five interrupts are remappable.

7: Comparator output is remappable.

8: The ADC2 module supports 10-bit mode only.

 2009-2012 Microchip Technology Inc. DS70616G-page 3

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Pin Diagrams

64-Pin QFN

Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See

Section 11.4 “Peripheral Pin Select” for available peripherals and for information on limitations.

2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0

“I/O Ports” for more information.

3: The availability of I2C™ interfaces varies by device. Selection (SDAx/SCLx or ASDAx/ASCLx) is

made using the device Configuration bits, ALTI2C1 and ALTI2C2 (FPOR<5:4>). See Section 29.0

“Special Features” for more information.

= Pins are up to 5V tolerant

dsPIC33EP256MU806

AN29/PWM3H/PMD5/RP85/RE5

AN31/PWM4H/PMD7/RP87/RE7

C1IN3-/SCK2/PMA5/RP118/RG6

C1IN1-/SDI2/PMA4/RPI119/RG7

C2IN3-/SDO2/PMA3/RP120/RG8

MCLR

C2IN1-/PMA2/RPI121/RG9

PGEC3/AN1/V

REF

-/RPI33/RB1

PGED3/AN0/V

REF

+/RPI32/RB0

AN30/PWM4L/PMD6/RPI86/RE6

PGEC2/SOSCO/C3IN1-/T1CK/RPI62/RC14

PGED2/SOSCI/C3IN3-/RPI61/RC13

INT0/DMH/RP64/RD0

PMCS1/RPI75/RD11

ASCL1/PMCS2/RPI74/RD10

ASDA1/DPLN/RPI73/RD9

RTCC/DMLN/RPI72/RD8

OSC2/CLKO/RC15

OSC1/RPI60/RC12

USBID/RP99/RF3

AN28/PWM3L/PMD4/RP84/RE4

AN27/PWM2H/PMD3/RPI83/RE3

AN26/PWM2L/PMD2/RP82/RE2

AN25/PWM1H/PMD1/RPI81/RE1

AN24/PWM1L/PMD0/RP80/RE0

VCMPST2/

RP97/RF1

CMPST

1/RP96/RF0

VCAP

C3IN1+/V

CMPST

3/RP71/RD7

C3IN2-/RP70/RD6

PMRD/RP69/RD5

PMWR/RP68/RD4

PMBE/RP67/RD3

DPH/RP66/RD2

VCPCON/RP65/RD1

PGEC1/AN6/RPI38/RB6

PGED1/AN7/RCV/RPI39/RB7

AN8/PMA6/RPI40/RB8

AN9/PMA7//RPI41/RB9

TMS/AN10/CV

REF

/PMA13/RPI42/RB10

TDO/AN11/PMA12/RPI43/RB11

VDD

TCK/AN12/PMA11/RPI44/RB12

TDI/AN13/PMA10/RPI45/RB13

AN14/PMA1/RPI46/RB14

AN15/PMA0/RPI47/RB15

SDA2/PMA9/RP100/RF4

SCL2/PMA8/RP101/RF5

D+/RG2

D-/RG3

USB

BUS

AN4/C1IN2-/USBOEN/RPI36/RB4

AN3/C2IN1+/VPIO/RPI35/RB3

AN2/C2IN2-/VMIO/RPI34/RB2

AN5/C1IN1+/VBUSON/VBUSST/RPI37/RB5

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 4  2009-2012 Microchip Technology Inc.

Pin Diagrams

64-Pin QFN

Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See

Section 11.4 “Peripheral Pin Select” for available peripherals and for information on limitations.

2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0

“I/O Ports” for more information.

3: The availability of I2C™ interfaces varies by device. Selection (SDAx/SCLx or ASDAx/ASCLx) is

made using the device Configuration bits, ALTI2C1 and ALTI2C2 (FPOR<5:4>). See Section 29.0

“Special Features” for more information.

= Pins are up to 5V tolerant

dsPIC33EP512MC806

AN29/PWM3H/PMD5/RP85/RE5

AN31/PWM4H/PMD7/RP87/RE7

C1IN3-/SCK2/PMA5/RP118/RG6

C1IN1-/SDI2/PMA4/RPI119/RG7

C2IN3-/SDO2/PMA3/RP120/RG8

MCLR

C2IN1-/PMA2/RPI121/RG9

PGEC3/AN1/V

REF

-/RPI33/RB1

PGED3/AN0/V

REF

+/RPI32/RB0

AN30/PWM4L/PMD6/RPI86/RE6

PGEC2/SOSCO/C3IN1-/T1CK/RPI62/RC14

PGED2/SOSCI/C3IN3-/RPI61/RC13

INT0/RP64/RD0

PMCS1/RPI75/RD11

ASCL1/PMCS2/RPI74/RD10

ASDA1/RPI73/RD9

RTCC/RPI72/RD8

OSC2/CLKO/RC15

OSC1/RPI60/RC12

RP99/RF3

AN28/PWM3L/PMD4/RP84/RE4

AN27/PWM2H/PMD3/RPI83/RE3

AN26/PWM2L/PMD2/RP82/RE2

AN25/PWM1H/PMD1/RPI81/RE1

AN24/PWM1L/PMD0/RP80/RE0

RP97/RF1

RP96/RF0

VCAP

C3IN1+/RP71/RD7

C3IN2-/RP70/RD6

PMRD/RP69/RD5

PMWR/RP68/RD4

PMBE/RP67/RD3

RP66/RD2

RP65/RD1

PGEC1/AN6/RPI38/RB6

PGED1/AN7/RPI39/RB7

AN8/PMA6/RPI40/RB8

AN9/PMA7//RPI41/RB9

TMS/AN10/CV

REF

/PMA13/RPI42/RB10

TDO/AN11/PMA12/RPI43/RB11

VDD

TCK/AN12/PMA11/RPI44/RB12

TDI/AN13/PMA10/RPI45/RB13

AN14/PMA1/RPI46/RB14

AN15/PMA0/RPI47/RB15

SDA2/PMA9/RP100/RF4

SCL2/PMA8/RP101/RF5

SCLI/RG2

SDA1/RG3

RP102/RF6

RP98/RF2

AN5/C1IN1+/RPI37/RB5

AN4/C1IN2-/RPI36/RB4

AN3/C2IN1+/RPI35/RB3

AN2/C2IN2-/RPI34/RB2

 2009-2012 Microchip Technology Inc. DS70616G-page 5

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Pin Diagrams

64-Pin QFN

Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See

Section 11.4 “Peripheral Pin Select” for available peripherals and for information on limitations.

2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0

“I/O Ports” for more information.

3: The availability of I2C™ interfaces varies by device. Selection (SDAx/SCLx or ASDAx/ASCLx) is

made using the device Configuration bits, ALTI2C1 and ALTI2C2 (FPOR<5:4>). See Section 29.0

“Special Features” for more information.

= Pins are up to 5V tolerant

dsPIC33EP512GP806

AN29/PMD5/RP85/RE5

AN31/PMD7/RP87/RE7

C1IN3-/SCK2/PMA5/RP118/RG6

C1IN1-/SDI2/PMA4/RPI119/RG7

C2IN3-/SDO2/PMA3/RP120/RG8

MCLR

C2IN1-/PMA2/RPI121/RG9

PGEC3/AN1/V

REF

-/RPI33/RB1

PGED3/AN0/V

REF

+/RPI32/RB0

AN30/PMD6/RPI86/RE6

PGEC2/SOSCO/C3IN1-/T1CK/RPI62/RC14

PGED2/SOSCI/C3IN3-/RPI61/RC13

INT0/RP64/RD0

PMCS1/RPI75/RD11

ASCL1/PMCS2/RPI74/RD10

ASDA1/RPI73/RD9

RTCC/RPI72/RD8

OSC2/CLKO/RC15

OSC1/RPI60/RC12

RP99/RF3

AN28/PMD4/RP84/RE4

AN27/PMD3/RPI83/RE3

AN26/PMD2/RP82/RE2

AN25/PMD1/RPI81/RE1

AN24/PMD0/RP80/RE0

RP97/RF1

RP96/RF0

VCAP

C3IN1+/RP71/RD7

C3IN2-/RP70/RD6

PMRD/RP69/RD5

PMWR/RP68/RD4

PMBE/RP67/RD3

RP66/RD2

RP65/RD1

PGEC1/AN6/RPI38/RB6

PGED1/AN7/RPI39/RB7

AN8/PMA6/RPI40/RB8

AN9/PMA7//RPI41/RB9

TMS/AN10/CV

REF

/PMA13/RPI42/RB10

TDO/AN11/PMA12/RPI43/RB11

VDD

TCK/AN12/PMA11/RPI44/RB12

TDI/AN13/PMA10/RPI45/RB13

AN14/PMA1/RPI46/RB14

AN15/PMA0/RPI47/RB15

SDA2/PMA9/RP100/RF4

SCL2/PMA8/RP101/RF5

SCLI/RG2

SDA1/RG3

RP102/RF6

RP98/RF2

AN5/C1IN1+/RPI37/RB5

AN4/C1IN2-/RPI36/RB4

AN3/C2IN1+/RPI35/RB3

AN2/C2IN2-/RPI34/RB2

PIC24EP512GP806

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 6  2009-2012 Microchip Technology Inc.

Pin Diagrams (Continued)

64-Pin TQFP

Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See

Section 11.4 “Peripheral Pin Select” for available peripherals and for information on limitations.

2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0

“I/O Ports” for more information.

3: The availability of I2C™ interfaces varies by device. Selection (SDAx/SCLx or ASDAx/ASCLx) is

made using the device Configuration bits, ALTI2C1 and ALTI2C2 (FPOR<5:4>). See Section 29.0

“Special Features” for more information.

= Pins are up to 5V tolerant

dsPIC33EP256MU806

AN29/PWM3H/PMD5/RP85/RE5

AN31/PWM4H/PMD7/RP87/RE7

C1IN3-/SCK2/PMA5/RP118/RG6

C1IN1-/SDI2/PMA4/RPI119/RG7

C2IN3-/SDO2/PMA3/RP120/RG8

MCLR

C2IN1-/PMA2/RPI121/RG9

AN5/C1IN1+/V

BUSON

BUSST

/RPI37/RB5

AN4/C1IN2-/USBOEN/RPI36/RB4

AN3/C2IN1+/VPIO/RPI35/RB3

AN2/C2IN2-/VMIO/RPI34/RB2

PGEC3/AN1/V

REF

-/RPI33/RB1

PGED3/AN0/V

REF

+/RPI32/RB0

AN30/PWM4L/PMD6/RPI86/RE6

PGEC2/SOSCO/C3IN1-/T1CK/RPI62/RC14

PGED2/SOSCI/C3IN3-/RPI61/RC13

INT0/DMH/RP64/RD0

PMCS1/RPI75/RD11

ASCL1/PMCS2/RPI74/RD10

ASDA1/DPLN/RPI73/RD9

RTCC/DMLN/RPI72/RD8

OSC2/CLKO/RC15

OSC1/RPI60/RC12

USBID/RP99/RF3

AN28/PWM3L/PMD4/RP84/RE4

AN27/PWM2H/PMD3/RPI83/RE3

AN26/PWM2L/PMD2/RP82/RE2

AN25/PWM1H/PMD1/RPI81/RE1

AN24/PWM1L/PMD0/RP80/RE0

CMPST

2/RP97/RF1

CMPST

1/RP96/RF0

CAP

C3IN1+/V

CMPST

3/RP71/RD7

C3IN2-/RP70/RD6

PMRD/RP69/RD5

PMWR/RP68/RD4

PMBE/RP67/RD3

DPH/RP66/RD2

CPCON

/RP65/RD1

PGEC1/AN6/RPI38/RB6

PGED1/AN7/RCV/RPI39/RB7

AN8/PMA6/RPI40/RB8

AN9/PMA7//RPI41/RB9

TMS/AN10/CV

REF

/PMA13/RPI42/RB10

TDO/AN11/PMA12/RPI43/RB11

TCK/AN12/PMA11/RPI44/RB12

TDI/AN13/PMA10/RPI45/RB13

AN14/PMA1/RPI46/RB14

AN15/PMA0/RPI47/RB15

SDA2/PMA9/RP100/RF4

SCL2/PMA8/RP101/RF5

D+/RG2

D-/RG3

USB

BUS

 2009-2012 Microchip Technology Inc. DS70616G-page 7

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Pin Diagrams (Continued)

64-Pin TQFP

Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See

Section 11.4 “Peripheral Pin Select” for available peripherals and for information on limitations.

2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0

“I/O Ports” for more information.

3: The availability of I2C™ interfaces varies by device. Selection (SDAx/SCLx or ASDAx/ASCLx) is

made using the device Configuration bits, ALTI2C1 and ALTI2C2 (FPOR<5:4>). See Section 29.0

“Special Features” for more information.

= Pins are up to 5V tolerant

dsPIC33EP512GP806

AN29/PMD5/RP85/RE5

AN31/PMD7/RP87/RE7

C1IN3-/SCK2/PMA5/RP118/RG6

C1IN1-/SDI2/PMA4/RPI119/RG7

C2IN3-/SDO2/PMA3/RP120/RG8

MCLR

C2IN1-/PMA2/RPI121/RG9

AN5/C1IN1+/RPI37/RB5

AN4/C1IN2-/RPI36/RB4

AN3/C2IN1+/RPI35/RB3

AN2/C2IN2-/RPI34/RB2

PGEC3/AN1/V

REF

-/RPI33/RB1

PGED3/AN0/V

REF

+/RPI32/RB0

AN30/PMD6/RPI86/RE6

PGEC2/SOSCO/C3IN1-/T1CK/RPI62/RC14

PGED2/SOSCI/C3IN3-/RPI61/RC13

INT0/RP64/RD0

PMCS1/RPI75/RD11

ASCL1/PMCS2/RPI74/RD10

ASDA1/RPI73/RD9

RTCC/RPI72/RD8

OSC2/CLKO/RC15

OSC1/RPI60/RC12

RP99/RF3

AN28/PMD4/RP84/RE4

AN27/PMD3/RPI83/RE3

AN26/PMD2/RP82/RE2

AN25/PMD1/RPI81/RE1

AN24/PMD0/RP80/RE0

RP97/RF1

RP96/RF0

CAP

C3IN1+/RP71/RD7

C3IN2-/RP70/RD6

PMRD/RP69/RD5

PMWR/RP68/RD4

PMBE/RP67/RD3

RP66/RD2

RP65/RD1

PGEC1/AN6/RPI38/RB6

PGED1/AN7/RPI39/RB7

AN8/PMA6/RPI40/RB8

AN9/PMA7//RPI41/RB9

TMS/AN10/CV

REF

/PMA13/RPI42/RB10

TDO/AN11/PMA12/RPI43/RB11

TCK/AN12/PMA11/RPI44/RB12

TDI/AN13/PMA10/RPI45/RB13

AN14/PMA1/RPI46/RB14

AN15/PMA0/RPI47/RB15

SDA2/PMA9/RP100/RF4

SCL2/PMA8/RP101/RF5

SCL1/RG2

SDA1/RG3

RP102/RF6

RP98/RF2

PIC24EP512GP806

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 8  2009-2012 Microchip Technology Inc.

Pin Diagrams (Continued)

64-Pin TQFP

Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See

Section 11.4 “Peripheral Pin Select” for available peripherals and for information on limitations.

2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0

“I/O Ports” for more information.

3: The availability of I2C™ interfaces varies by device. Selection (SDAx/SCLx or ASDAx/ASCLx) is

made using the device Configuration bits, ALTI2C1 and ALTI2C2 (FPOR<5:4>). See Section 29.0

“Special Features” for more information.

= Pins are up to 5V tolerant

dsPIC33EP512MC806

AN29/PWM3H/PMD5/RP85/RE5

AN31/PWM4H/PMD7/RP87/RE7

C1IN3-/SCK2/PMA5/RP118/RG6

C1IN1-/SDI2/PMA4/RPI119/RG7

C2IN3-/SDO2/PMA3/RP120/RG8

MCLR

C2IN1-/PMA2/RPI121/RG9

AN5/C1IN1+/RPI37/RB5

AN4/C1IN2-/RPI36/RB4

AN3/C2IN1+/RPI35/RB3

AN2/C2IN2-/RPI34/RB2

PGEC3/AN1/V

REF

-/RPI33/RB1

PGED3/AN0/V

REF

+/RPI32/RB0

AN30/PWM4L/PMD6/RPI86/RE6

PGEC2/SOSCO/C3IN1-/T1CK/RPI62/RC14

PGED2/SOSCI/C3IN3-/RPI61/RC13

INT0/RP64/RD0

PMCS1/RPI75/RD11

ASCL1/PMCS2/RPI74/RD10

ASDA1/RPI73/RD9

RTCC/RPI72/RD8

OSC2/CLKO/RC15

OSC1/RPI60/RC12

RP99/RF3

AN28/PWM3L/PMD4/RP84/RE4

AN27/PWM2H/PMD3/RPI83/RE3

AN26/PWM2L/PMD2/RP82/RE2

AN25/PWM1H/PMD1/RPI81/RE1

AN24/PWM1L/PMD0/RP80/RE0

RP97/RF1

RP96/RF0

CAP

C3IN1+/RP71/RD7

C3IN2-/RP70/RD6

PMRD/RP69/RD5

PMWR/RP68/RD4

PMBE/RP67/RD3

RP66/RD2

RP65/RD1

PGEC1/AN6/RPI38/RB6

PGED1/AN7/RPI39/RB7

AN8/PMA6/RPI40/RB8

AN9/PMA7//RPI41/RB9

TMS/AN10/CV

REF

/PMA13/RPI42/RB10

TDO/AN11/PMA12/RPI43/RB11

TCK/AN12/PMA11/RPI44/RB12

TDI/AN13/PMA10/RPI45/RB13

AN14/PMA1/RPI46/RB14

AN15/PMA0/RPI47/RB15

SDA2/PMA9/RP100/RF4

SCL2/PMA8/RP101/RF5

SCL1/RG2

SDA1/RG3

RP102/RF6

RP98/RF2

 2009-2012 Microchip Technology Inc. DS70616G-page 9

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Pin Diagrams (Continued)

100-Pin TQFP

Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See

Section 11.4 “Peripheral Pin Select” for available peripherals and for information on limitations.

2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0

“I/O Ports” for more information.

3: The availability of I2C™ interfaces varies by device. Selection (SDAx/SCLx or ASDAx/ASCLx) is

made using the device Configuration bits, ALTI2C1 and ALTI2C2 (FPOR<5:4>). See Section 29.0

“Special Features” for more information.

= Pins are up to 5V tolerant

100

dsPIC33EP512MU810

PGEC1/AN6/RPI38/RB6

PGED1/AN7/RCV/RPI39/RB7

REF

-/RA9

REF

+/RA10

AN8/PMA6/RPI40/RB8

AN9/PMA7//RPI41/RB9

AN10/CV

REF

/PMA13/RPI42/RB10

AN11/PMA12/RPI43/RB11

TCK/RPI17/RA1

RP109/RF13

RP108/RF12

AN12/PMA11/RPI44/RB12

AN13/PMA10/RPI45/RB13

AN14/PMA1/RPI46/RB14

AN15/PMA0/RPI47/RB15

RPI78/RD14

RP79/RD15

SDA2/PMA9/RP100/RF4

SCL2/PMA8/RP101/RF5

PGEC2/SOSCO/C3IN1-/T1CK/RPI62/RC14

PGED2/SOSCI/C3IN3-/RPI61/RC13

INT0/DMH/RP64/RD0

PMCS1/RPI75/RD11

ASCL1/PMCS2/RPI74/RD10

ASDA1/DPLN/RPI73/RD9

RTCC/DMLN/RPI72/RD8

RPI31/RA15

RPI30/RA14

OSC2/CLKO/RC15

OSC1/RPI60/RC12

TDO/RPI21/RA5

TDI/RPI20/RA4

ASDA2/RPI19/RA3

ASCL2/RPI18/RA2

RP98/RF2

USBID/RP99/RF3

AN28/PWM3L/PMD4/RP84/RE4

AN27/PWM2H/PMD3/RPI83/RE3

AN26/PWM2L/PMD2/RP82/RE2

RP125/RG13

RPI124/RG12

RP126/RG14

AN25/PWM1H/PMD1/RPI81/RE1

AN24/PWM1L/PMD0/RP80/RE0

AN23/RPI23/RA7

AN22/RPI22/RA6

RP112/RG0

RP113/RG1

CMPST

2/RP97/RF1

CMPST

1/RP96/RF0

CAP

C3IN1+/V

CMPST

3/RP71/RD7

C3IN2-/RP70/RD6

PMRD/RP69/RD5

PMWR/RP68/RD4

RPI77/RD13

RPI76/RD12

PMBE/RP67/RD3

DPH/RP66/RD2

CPCON

/RP65/RD1

D+/RG2

D-/RG3

USB

BUS

dsPIC33EP256MU810

AN29/PWM3H/PMD5/RP85/RE5

AN31/PWM4H/PMD7/RP87/RE7

C1IN3-/SCK2/PMA5/RP118/RG6

C1IN1-/SDI2/PMA4/RPI119/RG7

C2IN3-/SDO2/PMA3/RP120/RG8

MCLR

C2IN1-/PMA2/RPI121/RG9

AN2/C2IN2-/VMIO/RPI34/RB2

PGEC3/AN1/RPI33/RB1

PGED3/AN0/RPI32/RB0

AN30/PWM4L/PMD6/RPI86/RE6

TMS/RPI16/RA0

AN20/RPI88/RE8

AN21/RPI89/RE9

RP127/RG15

AN16/PWM5L/RPI49/RC1

AN17/PWM5H/RPI50/RC2

AN18/PWM6L/RPI51/RC3

AN19/PWM6H/RPI52/RC4

RP104/RF8

AN5/C1IN1+/VBUSON//VBUSST/RPI37/RB5

AN4/C1IN2-/USBOEN/RPI36/RB4

AN3/C2IN1+/VPIO/RPI35/RB3

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 10  2009-2012 Microchip Technology Inc.

Pin Diagrams (Continued)

100-Pin TQFP

Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See

Section 11.4 “Peripheral Pin Select” for available peripherals and for information on limitations.

2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0

“I/O Ports” for more information.

3: The availability of I2C™ interfaces varies by device. Selection (SDAx/SCLx or ASDAx/ASCLx) is

made using the device Configuration bits, ALTI2C1 and ALTI2C2 (FPOR<5:4>). See Section 29.0

“Special Features” for more information.

= Pins are up to 5V tolerant

100

PGEC1/AN6/RPI38/RB6

PGED1/AN7/RCV/RPI39/RB7

REF

-/RA9

REF

+/RA10

AN8/PMA6/RPI40/RB8

AN9/PMA7//RPI41/RB9

AN10/CV

REF

/PMA13/RPI42/RB10

AN11/PMA12/RPI43/RB11

TCK/RPI17/RA1

RP109/RF13

RP108/RF12

AN12/PMA11/RPI44/RB12

AN13/PMA10/RPI45/RB13

AN14/PMA1/RPI46/RB14

AN15/PMA0/RPI47/RB15

RPI78/RD14

RP79/RD15

SDA2/PMA9/RP100/RF4

SCL2/PMA8/RP101/RF5

PGEC2/SOSCO/C3IN1-/T1CK/RPI62/RC14

PGED2/SOSCI/C3IN3-/RPI61/RC13

INT0/DMH/RP64/RD0

PMCS1/RPI75/RD11

ASCL1/PMCS2/RPI74/RD10

ASDA1/DPLN/RPI73/RD9

RTCC/DMLN/RPI72/RD8

RPI31/RA15

RPI30/RA14

OSC2/CLKO/RC15

OSC1/RPI60/RC12

TDO/RPI21/RA5

TDI/RPI20/RA4

ASDA2/RPI19/RA3

ASCL2/RPI18/RA2

RP98/RF2

USBID/RP99/RF3

AN28/PMD4/RP84/RE4

AN27/PMD3/RPI83/RE3

AN26/PMD2/RP82/RE2

RP125/RG13

RPI124/RG12

RP126/RG14

AN25/PMD1/RPI81/RE1

AN24/PMD0/RP80/RE0

AN23/RPI23/RA7

AN22/RPI22/RA6

RP112/RG0

RP113/RG1

CMPST

2/RP97/RF1

CMPST

1/RP96/RF0

CAP

C3IN1+/V

CMPST

3/RP71/RD7

C3IN2-/RP70/RD6

PMRD/RP69/RD5

PMWR/RP68/RD4

RPI77/RD13

RPI76/RD12

PMBE/RP67/RD3

DPH/RP66/RD2

CPCON

/RP65/RD1

D+/RG2

D-/RG3

USB

BUS

AN29/PMD5/RP85/RE5

AN31/PMD7/RP87/RE7

C1IN3-/SCK2/PMA5/RP118/RG6

C1IN1-/SDI2/PMA4/RPI119/RG7

C2IN3-/SDO2/PMA3/RP120/RG8

MCLR

C2IN1-/PMA2/RPI121/RG9

AN5/C1IN1+/

BUSON

BUSST

/RPI37/RB5

AN4/C1IN2-/USBOEN/RPI36/RB4

AN3/C2IN1+/VPIO/RPI35/RB3

AN2/C2IN2-/VMIO/RPI34/RB2

PGEC3/AN1/RPI33/RB1

PGED3/AN0/RPI32/RB0

AN30/PMD6/RPI86/RE6

TMS/RPI16/RA0

AN20/RPI88/RE8

AN21/RPI89/RE9

RP127/RG15

AN16/RPI49/RC1

AN17/RPI50/RC2

AN18/RPI51/RC3

AN19/RPI52/RC4

PIC24EP512GU810

PIC24EP256GU810

RP104/RF8

 2009-2012 Microchip Technology Inc. DS70616G-page 11

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Pin Diagrams (Continued)

121-Pin TFBGA(1)

1234567891011

RE4 RE3 RG13 RE0 RG0 RF1 VDD NC RD12 RD2 RD1

BNC RG15 RE2 RE1 RA7 RF0 VCAP RD5 RD3 VSS RC14

RE6 VDD RG12 RG14 RA6 NC RD7 RD4 NC RC13 RD11

RC1 RE7 RE5 NC NC NC RD6 RD13 RD0 NC RD10

RC4 RC3 RG6 RC2 NC RG1 NC RA15 RD8 RD9 RA14

MCLR RG8 RG9 RG7 VSS NC NC VDD RC12 VSS RC15

RE8 RE9 RA0 NC VDD VSS VSS NC RA5 RA3 RA4

RB5 RB4 NC NC NC VDD NC VBUS VUSB3V3 RG2 RA2

RB3 RB2 RB7 AVDD RB11 RA1 RB12 NC NC RF8 RG3

RB1 RB0 RA10 RB8 NC RF12 RB14 VDD RD15 RF3 RF2

RB6 RA9 AVSS RB9 RB10 RF13 RB13 RB15 RD14 RF4 RF5

dsPIC33EP256MU810

Note 1: Refer to Table 2 for full pin names.

= Pins are up to 5V tolerant

dsPIC33EP512MU810

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 12  2009-2012 Microchip Technology Inc.

TABLE 2: PIN NAMES: dsPIC33EP256MU810 AND dsPIC33EP512MU810

DEVICES(1,2)

Number Full Pin Name Pin

Number Full Pin Name

A1 AN28/PWM3L/PMD4/RP84/RE4 E8 RPI31/RA15

A2 AN27/PWM2H/PMD3/RPI83/RE3 E9 RTCC/DMLN/RPI72/RD8

A3 RP125/RG13 E10 ASDA1(3)/DPLN/RPI73/RD9

A4 AN24/PWM1L/PMD0/RP80/RE0 E11 RPI30/RA14

A5 RP112/RG0 F1 MCLR

A6 VCMPST2/RP97/RF1 F2 C2IN3-/SDO2/PMA3/RP120/RG8

A7 VDD F3 C2IN1-/PMA2/RPI121/RG9

A8 No Connect F4 C1IN1-/SDI2/PMA4/RPI119/RG7

A9 RPI76/RD12 F5 VSS

A10 DPH/RP66/RD2 F6 No Connect

A11 VCPCON/RP65/RD1 F7 No Connect

B1 No Connect F8 VDD

B2 RP127/RG15 F9 OSC1/RPI60/RC12

B3 AN26/PWM2L/PMD2/RP82/RE2 F10 VSS

B4 AN25/PWM1H/PMD1/RPI81/RE1 F11 OSC2/CLKO/RC15

B5 AN23/RPI23/RA7 G1 AN20/RPI88/RE8

B6 VCMPST1/RP96/RF0 G2 AN21/RPI89/RE9

B7 VCAP G3 TMS/RPI16/RA0

B8 PMRD/RP69/RD5 G4 No Connect

B9 PMBE/RP67/RD3 G5 VDD

B10 VSS G6 VSS

B11 PGEC2/SOSCO/C3IN1-/T1CK/RPI62/RC14 G7 VSS

C1 AN30/PWM4L/PMD6/RPI86/RE6 G8 No Connect

C2 VDD G9 TDO/RPI21/RA5

C3 RPI124/RG12 G10 ASDA2(3)/RPI19/RA3

C4 RP126/RG14 G11 TDI/RPI20/RA4

C5 AN22/RPI22/RA6 H1 AN5/C1IN1+/VBUSON/VBUSST/RPI37/RB5

C6 No Connect H2 AN4/C1IN2-/USBOEN/RPI36/RB4

C7 C3IN1+/VCMPST3/RP71/RD7 H3 No Connect

C8 PMWR/RP68/RD4 H4 No Connect

C9 No Connect H5 No Connect

C10 PGED2/SOSCI/C3IN3-/RPI61/RC13 H6 VDD

C11 PMCS1/RPI75/RD11 H7 No Connect

D1 AN16/PWM5L/RPI49/RC1 H8 VBUS

D2 AN31/PWM4H/PMD7/RP87/RE7 H9 VUSB3V3

D3 AN29/PWM3H/PMD5/RP85/RE5 H10 D+/RG2(4)

D4 No Connect H11 ASCL2(3)/RPI18/RA2

D5 No Connect J1 AN3/C2IN1+/VPIO/RPI35/RB3

D6 No Connect J2 AN2/C2IN2-/VMIO/RPI34/RB2

D7 C3IN2-/RP70/RD6 J3 PGED1/AN7/RCV/RPI39/RB7

D8 RPI77/RD13 J4 AVDD

D9 INT0/DMH/RP64/RD0 J5 AN11/PMA12/RPI43/RB11

D10 No Connect J6 TCK/RPI17/RA1

D11 ASCL1(3)/PMCS2/RPI74/RD10 J7 AN12/PMA11/RPI44/RB12

Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See Section 11.4 “Peripheral Pin Select” for

available peripherals and for information on limitations.

2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0 “I/O Ports” for more information.

3: The availability of I2C™ interfaces varies by device. Selection (SDAx/SCLx or ASDAx/ASCLx) is made using the device Configuration bits,

ALTI2C1 and ALTI2C2 (FPOR<5:4>). See Section 29.0 “Special Features” for more information.

4: The pin name is SCL1/RG2 for the dsPIC33EP512(GP/MC)806 and PIC24EP512GP806 devices.

5: The pin name is SDA1/RG3 for the dsPIC33EP512(GP/MC)806 and PIC24EP512GP806 devices.

 2009-2012 Microchip Technology Inc. DS70616G-page 13

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

E1 AN19/PWM6H/RPI52/RC4 J8 No Connect

E2 AN18/PWM6L/RPI51/RC3 J9 No Connect

E3 C1IN3-/SCK2/PMA5/RP118/RG6 J10 RP104/RF8

E4 AN17/PWM5H/RPI50/RC2 J11 D-/RG3(5)

E5 No Connect K1 PGEC3/AN1/RPI33/RB1

E6 RP113/RG1 K2 PGED3/AN0/RPI32/RB0

E7 No Connect K3 VREF+/RA10

K4 AN8/PMA6/RPI40/RB8 L3 AVSS

K5 No Connect L4 AN9/PMA7//RPI41/RB9

K6 RP108/RF12 L5 AN10/CVREF/PMA13/RPI42/RB10

K7 AN14/PMA1/RPI46/RB14 L6 RP109/RF13

K8 VDD L7 AN13/PMA10/RPI45/RB13

K9 RP79/RD15 L8 AN15/PMA0/RPI47/RB15

K10 USBID/RP99/RF3 L9 RPI78/RD14

K11 RP98/RF2 L10 SDA2(3)/PMA9/RP100/RF4

L1 PGEC1/AN6/RPI38/RB6 L11 SCL2(3)/PMA8/RP101/RF5

L2 VREF-/RA9

TABLE 2: PIN NAMES: dsPIC33EP256MU810 AND dsPIC33EP512MU810

DEVICES(1,2) (CONTINUED)

Number Full Pin Name Pin

Number Full Pin Name

Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See Section 11.4 “Peripheral Pin Select” for

available peripherals and for information on limitations.

2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0 “I/O Ports” for more information.

3: The availability of I2C™ interfaces varies by device. Selection (SDAx/SCLx or ASDAx/ASCLx) is made using the device Configuration bits,

ALTI2C1 and ALTI2C2 (FPOR<5:4>). See Section 29.0 “Special Features” for more information.

4: The pin name is SCL1/RG2 for the dsPIC33EP512(GP/MC)806 and PIC24EP512GP806 devices.

5: The pin name is SDA1/RG3 for the dsPIC33EP512(GP/MC)806 and PIC24EP512GP806 devices.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 14  2009-2012 Microchip Technology Inc.

Pin Diagrams (Continued)

121-Pin TFBGA(1)

1234567891011

RE4 RE3 RG13 RE0 RG0 RF1 VDD NC RD12 RD2 RD1

BNC RG15 RE2 RE1 RA7 RF0 VCAP RD5 RD3 VSS RC14

RE6 VDD RG12 RG14 RA6 NC RD7 RD4 NC RC13 RD11

RC1 RE7 RE5 NC NC NC RD6 RD13 RD0 NC RD10

RC4 RC3 RG6 RC2 NC RG1 NC RA15 RD8 RD9 RA14

MCLR RG8 RG9 RG7 VSS NC NC VDD RC12 VSS RC15

RE8 RE9 RA0 NC VDD VSS VSS NC RA5 RA3 RA4

RB5 RB4 NC NC NC VDD NC VBUS VUSB3V3 RG2 RA2

RB3 RB2 RB7 AVDD RB11 RA1 RB12 NC NC RF8 RG3

RB1 RB0 RA10 RB8 NC RF12 RB14 VDD RD15 RF3 RF2

RB6 RA9 AVSS RB9 RB10 RF13 RB13 RB15 RD14 RF4 RF5

Note 1: Refer to Table 3 for full pin names.

= Pins are up to 5V tolerant

PIC24EP512GU810

PIC24EP256GU810

 2009-2012 Microchip Technology Inc. DS70616G-page 15

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 3: PIN NAMES: PIC24EP256GU810 AND PIC24EP512GU810

DEVICES(1,2)

Number Full Pin Name Pin

Number Full Pin Name

A1 AN28/PMD4/RP84/RE4 E8 RPI31/RA15

A2 AN27/PMD3/RPI83/RE3 E9 RTCC/DMLN/RPI72/RD8

A3 RP125/RG13 E10 ASDA1(3)/DPLN/RPI73/RD9

A4 AN24/PMD0/RP80/RE0 E11 RPI30/RA14

A5 RP112/RG0 F1 MCLR

A6 VCMPST2/RP97/RF1 F2 C2IN3-/SDO2/PMA3/RP120/RG8

A7 VDD F3 C2IN1-/PMA2/RPI121/RG9

A8 No Connect F4 C1IN1-/SDI2/PMA4/RPI119/RG7

A9 RPI76/RD12 F5 VSS

A10 DPH/RP66/RD2 F6 No Connect

A11 VCPCON/RP65/RD1 F7 No Connect

B1 No Connect F8 VDD

B2 RP127/RG15 F9 OSC1/RPI60/RC12

B3 AN26/PMD2/RP82/RE2 F10 VSS

B4 AN25/PMD1/RPI81/RE1 F11 OSC2/CLKO/RC15

B5 AN23/RPI23/RA7 G1 AN20/RPI88/RE8

B6 VCMPST1/RP96/RF0 G2 AN21/RPI89/RE9

B7 VCAP G3 TMS/RPI16/RA0

B8 PMRD/RP69/RD5 G4 No Connect

B9 PMBE/RP67/RD3 G5 VDD

B10 VSS G6 VSS

B11 PGEC2/SOSCO/C3IN1-/T1CK/RPI62/RC14 G7 VSS

C1 AN30/PMD6/RPI86/RE6 G8 No Connect

C2 VDD G9 TDO/RPI21/RA5

C3 RPI124/RG12 G10 ASDA2(3)/RPI19/RA3

C4 RP126/RG14 G11 TDI/RPI20/RA4

C5 AN22/RPI22/RA6 H1 AN5/C1IN1+/VBUSON/VBUSST/RPI37/RB5

C6 No Connect H2 AN4/C1IN2-/USBOEN/RPI36/RB4

C7 C3IN1+/VCMPST3/RP71/RD7 H3 No Connect

C8 PMWR/RP68/RD4 H4 No Connect

C9 No Connect H5 No Connect

C10 PGED2/SOSCI/C3IN3-/RPI61/RC13 H6 VDD

C11 PMCS1/RPI75/RD11 H7 No Connect

D1 AN16/RPI49/RC1 H8 VBUS

D2 AN31/PMD7/RP87/RE7 H9 VUSB3V3

D3 AN29/PMD5/RP85/RE5 H10 D+/RG2(4)

D4 No Connect H11 ASCL2(3)/RPI18/RA2

D5 No Connect J1 AN3/C2IN1+/VPIO/RPI35/RB3

D6 No Connect J2 AN2/C2IN2-/VMIO/RPI34/RB2

D7 C3IN2-/RP70/RD6 J3 PGED1/AN7/RCV/RPI39/RB7

D8 RPI77/RD13 J4 AVDD

D9 INT0/DMH/RP64/RD0 J5 AN11/PMA12/RPI43/RB11

D10 No Connect J6 TCK/RPI17/RA1

D11 ASCL1(3)/PMCS2/RPI74/RD10 J7 AN12/PMA11/RPI44/RB12

Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See Section 11.4 “Peripheral Pin Select” for

available peripherals and for information on limitations.

2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0 “I/O Ports” for more information.

3: The availability of I2C™ interfaces varies by device. Selection (SDAx/SCLx or ASDAx/ASCLx) is made using the device Configuration bits,

ALTI2C1 and ALTI2C2 (FPOR<5:4>). See Section 29.0 “Special Features” for more information.

4: The pin name is SCL1/RG2 for the dsPIC33EP512(GP/MC)806 and PIC24EP512GP806 devices.

5: The pin name is SDA1/RG3 for the dsPIC33EP512(GP/MC)806 and PIC24EP512GP806 devices.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 16  2009-2012 Microchip Technology Inc.

E1 AN19/RPI52/RC4 J8 No Connect

E2 AN18/RPI51/RC3 J9 No Connect

E3 C1IN3-/SCK2/PMA5/RP118/RG6 J10 RP104/RF8

E4 AN17/RPI50/RC2 J11 D-/RG3(5)

E5 No Connect K1 PGEC3/AN1/RPI33/RB1

E6 RP113/RG1 K2 PGED3/AN0/RPI32/RB0

E7 No Connect K3 VREF+/RA10

K4 AN8/PMA6/RPI40/RB8 L3 AVSS

K5 No Connect L4 AN9/PMA7/RPI41/RB9

K6 RP108/RF12 L5 AN10/CVREF/PMA13/RPI42/RB10

K7 AN14/PMA1/RPI46/RB14 L6 RP109/RF13

K8 VDD L7 AN13/PMA10/RPI45/RB13

K9 RP79/RD15 L8 AN15/PMA0/RPI47/RB15

K10 USBID/RP99/RF3 L9 RPI78/RD14

K11 RP98/RF2 L10 SDA2(3)/PMA9/RP100/RF4

L1 PGEC1/AN6/RPI38/RB6 L11 SCL2(3)/PMA8/RP101/RF5

L2 VREF-/RA9

TABLE 3: PIN NAMES: PIC24EP256GU810 AND PIC24EP512GU810

DEVICES(1,2) (CONTINUED)

Number Full Pin Name Pin

Number Full Pin Name

Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See Section 11.4 “Peripheral Pin Select” for

available peripherals and for information on limitations.

2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0 “I/O Ports” for more information.

3: The availability of I2C™ interfaces varies by device. Selection (SDAx/SCLx or ASDAx/ASCLx) is made using the device Configuration bits,

ALTI2C1 and ALTI2C2 (FPOR<5:4>). See Section 29.0 “Special Features” for more information.

4: The pin name is SCL1/RG2 for the dsPIC33EP512(GP/MC)806 and PIC24EP512GP806 devices.

5: The pin name is SDA1/RG3 for the dsPIC33EP512(GP/MC)806 and PIC24EP512GP806 devices.

 2009-2012 Microchip Technology Inc. DS70616G-page 17

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Pin Diagrams (Continued)

144-Pin TQFP, 144-pin LQFP

Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See

Section 11.4 “Peripheral Pin Select” for available peripherals and for information on limitations.

2: Every I/O port pin (RAx-RKx) can be used as change notification (CNAx-CNKx). See Section 11.0

“I/O Ports” for more information.

3: The availability of I2C interfaces varies by device. Selection (SDAx/SCLx or ASDAx/ASCLx) is made

using the device Configuration bits, ALTI2C1 and ALTI2C2 (FPOR<5:4>). See Section 29.0

“Special Features” for more information.

= Pins are up to 5V tolerant

108

139

dsPIC33EP512MU814

107

106

105

104

103

102

101

100

138

137

136

135

134

133

132

131

130

129

128

127

126

125

124

123

122

121

120

119

118

117

116

115

144

143

142

141

140

114

113

112

111

110

109

AN29/PWM3H/RP85/RE5

AN31/PWM4H/RP87/RE7

C1IN3-/SCK2/RP118/RG6

C1IN1-/SDI2/RPI119/RG7

C2IN3-/SDO2/RP120/RG8

MCLR

C2IN1-/RPI121/RG9

AN5/C1IN1+/V

BUSON

BUSST

/RPI37/RB5

AN4/C1IN2-/USBOEN/RPI36/RB4

AN3/C2IN1+/VPIO/RPI35/RB3

AN2/C2IN2-/VMIO/RPI34/RB2

PGEC3/AN1/RPI33/RB1

PGED3/AN0/RPI32/RB0

AN30/PWM4L/RPI86/RE6

TMS/RPI16/RA0

AN20/RPI88/RE8

AN21/RPI89/RE9

RK0

RK1

RJ14

RJ15

RP127/RG15

PWM7L/PMA8/RJ8

PWM7H/PMA9/RJ9

PMA10/RJ10

PMA11/RJ11

AN16/PWM5L/RPI49/RC1

AN17/PWM5H/RPI50/RC2

AN18/PWM6L/RPI51/RC3

AN19/PWM6H/RPI52/RC4

PMA12/RJ12

PMA13/RJ13

AN28/PWM3L/RP84/RE4

AN27/PWM2H/RPI83/RE3

AN26/PWM2L/RP82/RE2

RP125/RG13

RPI124/RG12

RP126/RG14

AN25/PWM1H/RPI81/RE1

AN24/PWM1L/RP80/RE0

PMA7/RJ7

PMA6/RJ6

PMA5/RJ5

PMA4/RJ4

AN23/RPI23/RA7

AN22/RPI22/RA6

RP112/RG0

RP113/RG1

CMPST

2/RP97/RF1

CMPST

1/RP96/RF0

CAP

C3IN1+/V

CMPST

3/RP71/RD7

C3IN2-/RP70/RD6

RP69/RD5

RP68/RD4

PMA3/RJ3

PMA2/RJ2

PMA1/RJ1

PMA0/RJ0

RPI77/RD13

RPI76/RD12

RP67/RD3

DPH/RP66/RD2

CPCON

/RP65/RD1

PGEC2/SOSCO/C3IN1-/T1CK/RPI62/RC14

PGED2/SOSCI/C3IN3-/RPI61/RC13

INT0/DMH/RP64/RD0

RH15

RH14

RH13

RH12

RPI75/RD11

ASCL1/RPI74/RD10

ASDA1/DPLN/RPI73/RD9

RTCC/DMLN/RPI72/RD8

RPI31/RA15

RPI30/RA14

PMCS1/RK11

PMCS2/RK12

OSC2/CLKO/RC15

OSC1/RPI60/RC12

TDO/RPI21/RA5

TDI/RPI20/RA4

ASDA2/RPI19/RA3

ASCL2/RPI18/RA2

RH11

RH10

RH9

RH8

RP104/RF8

RP98/RF2

USBID/RP99/RF3

PGEC1/AN6/RPI38/RB6

PGED1/AN7/RCV/RPI39/RB7

REF

-/RA9

REF

+/RA10

PMD0/RH0

PMD1/RH1

PMD2/RH2

PMD3/RH3

AN8/RPI40/RB8

AN9/RPI41/RB9

AN10/CV

REF

/RPI42/RB10

AN11/RPI43/RB11

PMRD/RK15

PMWR/RK14

PMBE/RK13

TCK/RPI17/RA1

RP109/RF13

RP108/RF12

AN12/RPI44/RB12

AN13/RPI45/RB13

AN14/RPI46/RB14

AN15/RPI47/RB15

PMD4/RH4

PMD5/RH5

PMD6/RH6

PMD7/RH7

RPI78/RD14

RP79/RD15

SDA2/RP100/RF4

SCL2/RP101/RF5

D+/RG2

D-/RG3

USB

BUS

dsPIC33EP256MU814

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 18  2009-2012 Microchip Technology Inc.

Pin Diagrams (Continued)

144-Pin TQFP, 144-pin LQFP

Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See Section 11.4

“Peripheral Pin Select” for available peripherals and for information on limitations.

2: Every I/O port pin (RAx-RKx) can be used as change notification (CNAx-CNKx). See Section 11.0 “I/O

Ports” for more information.

3: The availability of I2C interfaces varies by device. Selection (SDAx/SCLx or ASDAx/ASCLx) is made

using the device Configuration bits, ALTI2C1 and ALTI2C2 (FPOR<5:4>). See Section 29.0 “Special

Features” for more information.

= Pins are up to 5V tolerant

108

139

107

106

105

104

103

102

101

100

138

137

136

135

134

133

132

131

130

129

128

127

126

125

124

123

122

121

120

119

118

117

116

115

144

143

142

141

140

114

113

112

111

110

109

AN29/RP85/RE5

AN31/RP87/RE7

C1IN3-/SCK2/RP118/RG6

C1IN1-/SDI2/RPI119/RG7

C2IN3-/SDO2/RP120/RG8

MCLR

C2IN1-/RPI121/RG9

AN5/C1IN1+/V

BUSON

BUSST

/RPI37/RB5

AN4/C1IN2-/USBOEN/RPI36/RB4

AN3/C2IN1+/VPIO/RPI35/RB3

AN2/C2IN2-/VMIO/RPI34/RB2

PGEC3/AN1/RPI33/RB1

PGED3/AN0/RPI32/RB0

AN30/RPI86/RE6

TMS/RPI16/RA0

AN20/RPI88/RE8

AN21/RPI89/RE9

RK0

RK1

RJ14

RJ15

RP127/RG15

PMA8/RJ8

PMA9/RJ9

PMA10/RJ10

PMA11/RJ11

AN16/RPI49/RC1

AN17/RPI50/RC2

AN18/RPI51/RC3

AN19/RPI52/RC4

PMA12/RJ12

PMA13/RJ13

AN28/RP84/RE4

AN27/RPI83/RE3

AN26/RP82/RE2

RP125/RG13

RPI124/RG12

RP126/RG14

AN25/RPI81/RE1

AN24/RP80/RE0

PMA7/RJ7

PMA6/RJ6

PMA5/RJ5

PMA4/RJ4

AN23/RPI23/RA7

AN22/RPI22/RA6

RP112/RG0

RP113/RG1

CMPST

2/RP97/RF1

CMPST

1/RP96/RF0

CAP

C3IN1+/V

CMPST

3/RP71/RD7

C3IN2-/RP70/RD6

RP69/RD5

RP68/RD4

PMA3/RJ3

PMA2/RJ2

PMA1/RJ1

PMA0/RJ0

RPI77/RD13

RPI76/RD12

RP67/RD3

DPH/RP66/RD2

CPCON

/RP65/RD1

PGEC2/SOSCO/C3IN1-/T1CK/RPI62/RC14

PGED2/SOSCI/C3IN3-/RPI61/RC13

INT0/DMH/RP64/RD0

RH15

RH14

RH13

RH12

RPI75/RD11

ASCL1/RPI74/RD10

ASDA1/DPLN/RPI73/RD9

RTCC/DMLN/RPI72/RD8

RPI31/RA15

RPI30/RA14

PMCS1/RK11

PMCS2/RK12

OSC2/CLKO/RC15

OSC1/RPI60/RC12

TDO/RPI21/RA5

TDI/RPI20/RA4

ASDA2/RPI19/RA3

ASCL2/RPI18/RA2

RH11

RH10

RH9

RH8

RP104/RF8

RP98/RF2

USBID/RP99/RF3

PGEC1/AN6/RPI38/RB6

PGED1/AN7/RCV/RPI39/RB7

REF

-/RA9

REF

+/RA10

PMD0/RH0

PMD1/RH1

PMD2/RH2

PMD3/RH3

AN8/RPI40/RB8

AN9/RPI41/RB9

AN10/CV

REF

/RPI42/RB10

AN11/RPI43/RB11

PMRD/RK15

PMWR/RK14

PMBE/RK13

TCK/RPI17/RA1

RP109/RF13

RP108/RF12

AN12/RPI44/RB12

AN13/RPI45/RB13

AN14/RPI46/RB14

AN15/RPI47/RB15

PMD4/RH4

PMD5/RH5

PMD6/RH6

PMD7/RH7

RPI78/RD14

RP79/RD15

SDA2/RP100/RF4

SCL2/RP101/RF5

D+/RG2

D-/RG3

USB

BUS

PIC24EP512GU814

PIC24EP256GU814

 2009-2012 Microchip Technology Inc. DS70616G-page 19

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Table of Contents

1.0 Device Overview ........................................................................................................................................................................ 23

2.0 Guidelines for Getting Started with 16-Bit Digital Signal Controllers and Microcontrollers ........................................................ 31

3.0 CPU............................................................................................................................................................................................ 37

4.0 Memory Organization................................................................................................................................................................. 47

5.0 Flash Program Memory............................................................................................................................................................ 135

6.0 Resets ..................................................................................................................................................................................... 141

7.0 Interrupt Controller ................................................................................................................................................................... 145

8.0 Direct Memory Access (DMA).................................................................................................................................................. 159

9.0 Oscillator Configuration............................................................................................................................................................ 177

10.0 Power-Saving Features............................................................................................................................................................ 191

11.0 I/O Ports ................................................................................................................................................................................... 207

12.0 Timer1 ...................................................................................................................................................................................... 271

13.0 Timer2/3, Timer4/5, Timer6/7 and Timer8/9 ............................................................................................................................ 275

14.0 Input Capture............................................................................................................................................................................ 281

15.0 Output Compare....................................................................................................................................................................... 287

16.0 High-Speed PWM Module (dsPIC33EPXXX(MC/MU)8XX Devices Only) ............................................................................... 293

17.0 Quadrature Encoder Interface (QEI) Module (dsPIC33EPXXX(MC/MU)8XX Devices Only)................................................... 321

18.0 Serial Peripheral Interface (SPI)............................................................................................................................................... 337

19.0 Inter-Integrated Circuit™ (I2C™).............................................................................................................................................. 345

20.0 Universal Asynchronous Receiver Transmitter (UART) ........................................................................................................... 353

21.0 Enhanced CAN (ECAN™) Module........................................................................................................................................... 359

22.0 USB On-The-Go (OTG) Module (dsPIC33EPXXXMU8XX and PIC24EPGU8XX Devices Only) ............................................ 385

23.0 10-Bit/12-Bit Analog-to-Digital Converter (ADC) ...................................................................................................................... 413

24.0 Data Converter Interface (DCI) Module.................................................................................................................................... 429

25.0 Comparator Module.................................................................................................................................................................. 437

26.0 Real-Time Clock and Calendar (RTCC) .................................................................................................................................. 449

27.0 Programmable Cyclic Redundancy Check (CRC) Generator .................................................................................................. 461

28.0 Parallel Master Port (PMP)....................................................................................................................................................... 467

29.0 Special Features ...................................................................................................................................................................... 477

30.0 Instruction Set Summary .......................................................................................................................................................... 485

31.0 Development Support............................................................................................................................................................... 495

32.0 Electrical Characteristics .......................................................................................................................................................... 499

33.0 DC and AC Device Characteristics Graphs.............................................................................................................................. 573

34.0 Packaging Information.............................................................................................................................................................. 577

Appendix A: Revision History............................................................................................................................................................. 597

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 20  2009-2012 Microchip Technology Inc.

TO OUR VALUED CUSTOMERS

It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip

products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and

enhanced as new volumes and updates are introduced.

If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via

E-mail at docerrors@microchip.com or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We

welcome your feedback.

Most Current Data Sheet

To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at:

http://www.microchip.com

You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page.

The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000).

Errata

An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current

devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of

silicon and revision of document to which it applies.

To determine if an errata sheet exists for a particular device, please check with one of the following:

• Microchip’s Worldwide Web site; http://www.microchip.com

• Your local Microchip sales office (see last page)

When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are

using.

Customer Notification System

 2009-2012 Microchip Technology Inc. DS70616G-page 21

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Referenced Sources

This device data sheet is based on the following

individual chapters of the “dsPIC33E/PIC24E Family

Reference Manual”. These documents should be

considered as the general reference for the operation

of a particular module or device feature.

• Section 1. “Introduction” (DS70573)

• Section 2. “CPU” (DS70359)

• Section 3. “Data Memory” (DS70595)

• Section 4. “Program Memory” (DS70613)

• Section 5. “Flash Programming” (DS70609)

• Section 6. “Interrupts” (DS70600)

• Section 7. “Oscillator” (DS70580)

• Section 8. “Reset” (DS70602)

• Section 9. “Watchdog Timer and Power-Saving Modes” (DS70615)

• Section 10. “I/O Ports” (DS70598)

• Section 11. “Timers” (DS70362)

• Section 12. “Input Capture” (DS70352)

• Section 13. “Output Compare” (DS70358)

• Section 14. “High-Speed PWM” (DS70645)

• Section 15. “Quadrature Encoder Interface (QEI)” (DS70601)

• Section 16. “Analog-to-Digital Converter (ADC)” (DS70621)

• Section 17. “UART” (DS70582)

• Section 18. “Serial Peripheral Interface (SPI)” (DS70569)

• Section 19. “Inter-Integrated Circuit™ (I2C™)” (DS70330)

• Section 20. “Data Converter Interface (DCI)” (DS70356)

• Section 21. “Enhanced Controller Area Network (ECAN™)” (DS70353)

• Section 22. “Direct Memory Access (DMA)” (DS70348)

• Section 23. “CodeGuard™ Security” (DS70634)

• Section 24. “Programming and Diagnostics” (DS70608)

• Section 25. “USB On-The-Go (OTG)” (DS70571)

• Section 26. “Op Amp/Comparator” (DS70357)

• Section 27. “Programmable Cyclic Redundancy Check (CRC)” (DS70346)

• Section 28. “Parallel Master Port (PMP)” (DS70576)

• Section 29. “Real-Time Clock and Calendar (RTCC)” (DS70584)

• Section 30. “Device Configuration” (DS70618)

Note: To access the documents listed below,

browse to the documentation section

of the dsPIC33EP512MU814 product

page on the Microchip web site

(www.microchip.com).

In the event you are not able to access

the product page using the link above,

enter this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310#1

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 22  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 23

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

1.0 DEVICE OVERVIEW This document contains device-specific information

for the dsPIC33EPXXX(GP/MC/MU)806/810/814

and PIC24EPXXX(GP/GU)810/814 Digital Signal

Controller (DSC) and Microcontroller (MCU) devices.

The dsPIC33EPXXX(GP/MC/MU)806/810/814 devices

contain extensive Digital Signal Processor (DSP)

functionality with a high-performance 16-bit MCU

architecture.

Figure 1-1 illustrates a general block diagram

of the core and peripheral modules in

the dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 families of devices.

Table 1-1 lists the functions of the various pins shown

in the pinout diagrams.

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive resource. To com-

plement the information in this data

sheet, refer to the related section of the

“dsPIC33E/PIC24E Family Reference

Manual”, which is available from the

Microchip web site (www.microchip.com)

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 24  2009-2012 Microchip Technology Inc.

FIGURE 1-1: dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

BLOCK DIAGRAM

PORTA

PORTB

PORTD

PORTC

Power-up

Timer

Oscillator

Start-up Timer

Instruction

Decode and

Control

OSC1/CLKI

MCLR

VDD, VSS

UART1-

Timing

Generation

ECAN1,

PCH

Program Counter

16-Bit ALU

X Data Bus

I2C1,

DCI

PCU

ADC1,

Timers

Input

Capture

Output

Compare

16 16

Divide

Support

Engine(1)

DSP

ROM Latch

Y Data Bus(1)

EA MUX

X RAGU

X WAGU

Y AGU

(1)

AVDD, AVSS

UART4

SPI4

Interrupt

Controller PSV and Table

Data Access

Control Block

Stack

Control

Logic

Loop

Control

Logic

Data LatchData Latch

Y Data

RAM(1) X Data

RAM

Address

Latch

Address

Latch

Control Signals

to Various Blocks

SPI1-

Data Latch

X Address Bus

Y Address Bus

Literal Data

ADC2

Program Memory

Watchdog

Timer

POR/BOR

Address Latch

PMP

Comparator

CRC

RTCC

USB

I2C2

ECAN2

QEI1(1),

PWM(1)

QEI2(1)

(3-Channel)

PORTE

PORTF

PORTG

PORTH

PORTJ

PORTK

Remappable

Pins

Note 1: This feature or peripheral is only available on dsPIC33EPXXX(MC/MU)806/810/814 devices.

2: This feature or peripheral is only available on dsPIC33EPXXXMU806/810/814 and PIC24EPXXXGU806/810/814 devices.

OTG(2)

PCL

16 x 16

W Reg Array

 2009-2012 Microchip Technology Inc. DS70616G-page 25

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 1-1: PINOUT I/O DESCRIPTIONS

Pin Name Pin

Type

Buffer

Type PPS Description

AN0-AN31 I Analog No Analog input channels.

CLKI

CLKO

ST/

CMOS

—

External clock source input. Always associated with OSC1 pin function.

Oscillator crystal output. Connects to crystal or resonator in Crystal

Oscillator mode. Optionally functions as CLKO in RC and EC modes.

Always associated with OSC2 pin function.

OSC1

OSC2

I/O

ST/

CMOS

—

Oscillator crystal input. ST buffer when configured in RC mode; CMOS

otherwise.

Oscillator crystal output. Connects to crystal or resonator in Crystal

Oscillator mode. Optionally functions as CLKO in RC and EC modes.

SOSCI

SOSCO

ST/

CMOS

—

32.768 kHz low-power oscillator crystal input; CMOS otherwise.

32.768 kHz low-power oscillator crystal output.

IC1-IC16 I ST Yes Capture Inputs 1 through 16.

OCFA

OCFB

OCFC

OC1-OC16

—

Yes

Compare Fault A input (for Compare channels).

Compare Fault B input (for Compare channels).

Compare Fault C input (for Compare channels).

Compare Outputs 1 through 16.

INT0

INT1

INT2

INT3

INT4

Yes

External Interrupt 0.

External Interrupt 1.

External Interrupt 2.

External Interrupt 3.

External Interrupt 4.

RA0-RA7, RA9,

RA10, RA14, RA15

I/O ST No PORTA is a bidirectional I/O port.

RB0-RB15 I/O ST No PORTB is a bidirectional I/O port.

RC1-RC4,

RC12-RC15

I/O ST No PORTC is a bidirectional I/O port.

RD0-RD15 I/O ST No PORTD is a bidirectional I/O port.

RE0-RE9 I/O ST No PORTE is a bidirectional I/O port.

RF0-RF6, RF8

RF12, RF13

I/O ST No PORTF is a bidirectional I/O port.

RG0, RG1

RG2, RG3(3)

RG6-RG9,

RG12-RG15

I/O

PORTG is a bidirectional I/O port.

RH0-RH15 I/O ST No PORTH is a bidirectional I/O port.

RJ0-RJ15 I/O ST No PORTJ is a bidirectional I/O port.

RK0-RK1,

RK11-RK15

I/O ST No PORTK is a bidirectional I/O port.

Legend: CMOS = CMOS compatible input or output Analog = Analog input P = Power

ST = Schmitt Trigger input with CMOS levels O = Output I = Input

PPS = Peripheral Pin Select TTL = TTL input buffer

Note 1: This pin is available on dsPIC33EPXXX(MC/MU)806/810/814 devices only.

2: AVDD must be connected at all times.

3: These pins are input only on dsPIC33EPXXXMU8XX and PIC24EPXXXGU8XX devices.

4: These pins are only available on dsPIC33EPXXXMU8XX and PIC24EPXXXGU8XX devices.

5: The availability of I2C™ interfaces varies by device. Refer to the “Pin Diagrams” section for availability.

Selection (SDAx/SCLx or ASDAx/ASCLx) is made using the device Configuration bits, ALTI2C1 and

ALTI2C2 (FPOR<5:4>). See Section 29.0 “Special Features” for more information.

6: Analog functionality is activated by enabling the USB module and is not controlled by the ANSEL register.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 26  2009-2012 Microchip Technology Inc.

T1CK

T2CK

T3CK

T4CK

T5CK

T6CK

T7CK

T8CK

T9CK

Yes

Timer1 external clock input.

Timer2 external clock input.

Timer3 external clock input.

Timer4 external clock input.

Timer5 external clock input.

Timer6 external clock input.

Timer7 external clock input.

Timer8 external clock input.

Timer9 external clock input.

U1CTS

U1RTS

U1RX

U1TX

—

Yes

UART1 Clear-to-Send.

UART1 Ready-to-Send.

UART1 receive.

UART1 transmit.

U2CTS

U2RTS

U2RX

U2TX

—

Yes

UART2 Clear-to-Send.

UART2 Ready-to-Send.

UART2 receive.

UART2 transmit.

U3CTS

U3RTS

U3RX

U3TX

—

Yes

UART3 Clear-to-Send.

UART3 Ready-to-Send.

UART3 receive.

UART3 transmit.

U4CTS

U4RTS

U4RX

U4TX

—

Yes

UART4 Clear-to-Send.

UART4 Ready-to-Send.

UART4 receive.

UART4 transmit.

SCK1

SDI1

SDO1

SS1

I/O

—

Yes

Synchronous serial clock input/output for SPI1.

SPI1 data in.

SPI1 data out.

SPI1 slave synchronization or frame pulse I/O.

SCK2

SDI2

SDO2

SS2

I/O

—

Yes

Synchronous serial clock input/output for SPI2.

SPI2 data in.

SPI2 data out.

SPI2 slave synchronization or frame pulse I/O.

SCK3

SDI3

SDO3

SS3

I/O

—

Yes

Synchronous serial clock input/output for SPI3.

SPI3 data in.

SPI3 data out.

SPI3 slave synchronization or frame pulse I/O.

SCK4

SDI4

SDO4

SS4

I/O

—

Yes

Synchronous serial clock input/output for SPI4.

SPI4 data in.

SPI4 data out.

SPI4 slave synchronization or frame pulse I/O.

TABLE 1-1: PINOUT I/O DESCRIPTIONS (CONTINUED)

Pin Name Pin

Type

Buffer

Type PPS Description

Legend: CMOS = CMOS compatible input or output Analog = Analog input P = Power

ST = Schmitt Trigger input with CMOS levels O = Output I = Input

PPS = Peripheral Pin Select TTL = TTL input buffer

Note 1: This pin is available on dsPIC33EPXXX(MC/MU)806/810/814 devices only.

2: AVDD must be connected at all times.

3: These pins are input only on dsPIC33EPXXXMU8XX and PIC24EPXXXGU8XX devices.

4: These pins are only available on dsPIC33EPXXXMU8XX and PIC24EPXXXGU8XX devices.

5: The availability of I2C™ interfaces varies by device. Refer to the “Pin Diagrams” section for availability.

Selection (SDAx/SCLx or ASDAx/ASCLx) is made using the device Configuration bits, ALTI2C1 and

ALTI2C2 (FPOR<5:4>). See Section 29.0 “Special Features” for more information.

6: Analog functionality is activated by enabling the USB module and is not controlled by the ANSEL register.

 2009-2012 Microchip Technology Inc. DS70616G-page 27

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

SCL1(5)

SDA1(5)

ASCL1(5)

ASDA1(5)

I/O

Synchronous serial clock input/output for I2C1.

Synchronous serial data input/output for I2C1.

Alternate synchronous serial clock input/output for I2C1.

Alternate synchronous serial data input/output for I2C1.

SCL2(5)

SDA2(5)

ASCL2(5)

ASDA2(5)

I/O

Synchronous serial clock input/output for I2C2.

Synchronous serial data input/output for I2C2.

Alternate synchronous serial clock input/output for I2C2.

Alternate synchronous serial data input/output for I2C2.

TMS

TCK

TDI

TDO

—

JTAG Test mode select pin.

JTAG test clock input pin.

JTAG test data input pin.

JTAG test data output pin.

INDX1(1)

HOME1(1)

QEA1(1)

QEB1(1)

CNTCMP1(1)

—

Yes

Quadrature Encoder Index1 pulse input.

Quadrature Encoder Home1 pulse input.

Quadrature Encoder Phase A input in QEI1 mode. Auxiliary timer

external clock input in Timer mode.

Quadrature Encoder Phase A input in QEI1 mode. Auxiliary timer

external gate input in Timer mode.

Quadrature Encoder Compare Output 1.

INDX2(1)

HOME2(1)

QEA2(1)

QEB2(1)

CNTCMP2(1)

—

Yes

Quadrature Encoder Index2 pulse input.

Quadrature Encoder Home2 pulse input.

Quadrature Encoder Phase A input in QEI2 mode. Auxiliary timer

external clock input in Timer mode.

Quadrature Encoder Phase B input in QEI2 mode. Auxiliary timer

external gate input in Timer mode.

Quadrature Encoder Compare Output 2.

COFS

CSCK

CSDI

CSDO

I/O

—

Yes

Data Converter Interface frame synchronization pin.

Data Converter Interface serial clock input/output pin.

Data Converter Interface serial data input pin.

Data Converter Interface serial data output pin.

C1RX

C1TX

—

Yes

ECAN1 bus receive pin.

ECAN1 bus transmit pin.

C2RX

C2TX

—

Yes

ECAN2 bus receive pin.

ECAN2 bus transmit pin.

RTCC O — No Real-Time Clock alarm output.

CVREF O Analog No Comparator voltage reference output.

C1IN1+, C1IN2-,

C1IN1-, C1IN3-

C1OUT

Analog

—

Yes

Comparator 1 inputs

Comparator 1 output.

TABLE 1-1: PINOUT I/O DESCRIPTIONS (CONTINUED)

Pin Name Pin

Type

Buffer

Type PPS Description

Legend: CMOS = CMOS compatible input or output Analog = Analog input P = Power

ST = Schmitt Trigger input with CMOS levels O = Output I = Input

PPS = Peripheral Pin Select TTL = TTL input buffer

Note 1: This pin is available on dsPIC33EPXXX(MC/MU)806/810/814 devices only.

2: AVDD must be connected at all times.

3: These pins are input only on dsPIC33EPXXXMU8XX and PIC24EPXXXGU8XX devices.

4: These pins are only available on dsPIC33EPXXXMU8XX and PIC24EPXXXGU8XX devices.

5: The availability of I2C™ interfaces varies by device. Refer to the “Pin Diagrams” section for availability.

Selection (SDAx/SCLx or ASDAx/ASCLx) is made using the device Configuration bits, ALTI2C1 and

ALTI2C2 (FPOR<5:4>). See Section 29.0 “Special Features” for more information.

6: Analog functionality is activated by enabling the USB module and is not controlled by the ANSEL register.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 28  2009-2012 Microchip Technology Inc.

C2IN1+, C2IN2-,

C2IN1-, C2IN3-

C2OUT

Analog

—

Yes

Comparator 2 inputs.

Comparator 2 output.

C3IN1+, C3IN2-,

C2IN1-, C3IN3-

C3OUT

Analog

—

Yes

Comparator 3 inputs.

Comparator 3 output.

PMA0

PMA1

PMA2 -PMA13

PMBE

PMCS1, PMCS2

PMD0-PMD7

PMRD

PMWR

I/O

TTL/ST

—

TTL/ST

—

Parallel Master Port Address Bit 0 input (Buffered Slave modes) and

output (Master modes).

Parallel Master Port Address Bit 1 input (Buffered Slave modes) and

output (Master modes).

Parallel Master Port Address Bits 2-13 (Demultiplexed Master modes).

Parallel Master Port byte enable strobe.

Parallel Master Port Chip Select 1 and 2 strobe.

Parallel Master Port data (Demultiplexed Master mode) or address/data

(Multiplexed Master modes).

Parallel Master Port read strobe.

Parallel Master Port write strobe.

FLT1-FLT7(1)

DTCMP1-DTCMP7(1)

PWM1L-PWM7L(1)

PWM1H-PWM7H(1)

SYNCI1, SYNCI2(1)

SYNCO1, SYNCO2(1)

—

Yes

PWM Fault Input 1 through 7.

PWM dead-time compensation input.

PWM Low Output 1 through 7.

PWM High Output 1 through 7.

PWM Synchronization Inputs 1 and 2.

PWM Synchronization Outputs 1 and 2.

TABLE 1-1: PINOUT I/O DESCRIPTIONS (CONTINUED)

Pin Name Pin

Type

Buffer

Type PPS Description

Legend: CMOS = CMOS compatible input or output Analog = Analog input P = Power

ST = Schmitt Trigger input with CMOS levels O = Output I = Input

PPS = Peripheral Pin Select TTL = TTL input buffer

Note 1: This pin is available on dsPIC33EPXXX(MC/MU)806/810/814 devices only.

2: AVDD must be connected at all times.

3: These pins are input only on dsPIC33EPXXXMU8XX and PIC24EPXXXGU8XX devices.

4: These pins are only available on dsPIC33EPXXXMU8XX and PIC24EPXXXGU8XX devices.

5: The availability of I2C™ interfaces varies by device. Refer to the “Pin Diagrams” section for availability.

Selection (SDAx/SCLx or ASDAx/ASCLx) is made using the device Configuration bits, ALTI2C1 and

ALTI2C2 (FPOR<5:4>). See Section 29.0 “Special Features” for more information.

6: Analog functionality is activated by enabling the USB module and is not controlled by the ANSEL register.

 2009-2012 Microchip Technology Inc. DS70616G-page 29

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

VBUS(4,6)

VUSB3V3(4)

VBUSON(4)

D+(4,6)

D-(4,6)

USBID(4)

USBOEN(4)

VBUSST(4)

VCPCON(4)

VCMPST1(4)

VCMPST2(4)

VCMPST3(4)

VMIO(4)

VPIO(4)

DMH(4)

DPH(4)

DMLN(4)

DPLN(4)

RCV(4)

I/O

Analog

—

Analog

—

USB bus power monitor.

USB internal transceiver supply. If the USB module is not being used,

this pin must be connected to VDD.

USB host and On-The-Go (OTG) bus power control output.

D+ pin of internal USB transceiver.

D- pin of internal USB transceiver.

USB OTG ID detect.

USB output enabled control (for external transceiver).

USB boost controller overcurrent detection.

USB boost controller PWM signal.

USB External Comparator 1 input.

USB External Comparator 2 input.

USB External Comparator 3 input.

USB differential minus input/output (external transceiver).

USB differential plus input/output (external transceiver).

D- external pull-up control output.

D+ external pull-up control output.

D- external pull-down control output.

D+ External Pull-down Control Output.

USB receive input (from external transceiver).

PGED1

PGEC1

PGED2

PGEC2

PGED3

PGEC3

I/O

Data I/O pin for Programming/Debugging Communication Channel 1.

Clock input pin for Programming/Debugging Communication Channel 1.

Data I/O pin for Programming/Debugging Communication Channel 2.

Clock input pin for Programming/Debugging Communication Channel 2.

Data I/O pin for Programming/Debugging Communication Channel 3.

Clock input pin for Programming/Debugging Communication Channel 3.

MCLR I/P ST No Master Clear (Reset) input. This pin is an active-low Reset to the

device.

AVDD(2)P P No Positive supply for analog modules. This pin must be connected at all

times.

AVSS P P No Ground reference for analog modules.

VDD P — No Positive supply for peripheral logic and I/O pins.

VCAP P — No CPU logic filter capacitor connection.

VSS P — No Ground reference for logic and I/O pins.

VREF+ I Analog No Analog voltage reference (high) input.

VREF- I Analog No Analog voltage reference (low) input.

TABLE 1-1: PINOUT I/O DESCRIPTIONS (CONTINUED)

Pin Name Pin

Type

Buffer

Type PPS Description

Legend: CMOS = CMOS compatible input or output Analog = Analog input P = Power

ST = Schmitt Trigger input with CMOS levels O = Output I = Input

PPS = Peripheral Pin Select TTL = TTL input buffer

Note 1: This pin is available on dsPIC33EPXXX(MC/MU)806/810/814 devices only.

2: AVDD must be connected at all times.

3: These pins are input only on dsPIC33EPXXXMU8XX and PIC24EPXXXGU8XX devices.

4: These pins are only available on dsPIC33EPXXXMU8XX and PIC24EPXXXGU8XX devices.

5: The availability of I2C™ interfaces varies by device. Refer to the “Pin Diagrams” section for availability.

Selection (SDAx/SCLx or ASDAx/ASCLx) is made using the device Configuration bits, ALTI2C1 and

ALTI2C2 (FPOR<5:4>). See Section 29.0 “Special Features” for more information.

6: Analog functionality is activated by enabling the USB module and is not controlled by the ANSEL register.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 30  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 31

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

2.0 GUIDELINES FOR GETTING

STARTED WITH 16-BIT DIGITAL

SIGNAL CONTROLLERS AND

MICROCONTROLLERS

2.1 Basic Connection Requirements

Getting started with the 16-bit DSCs and microcontrollers

requires attention to a minimal set of device pin

connections before proceeding with development. The

following is a list of pin names, which must always be

connected:

• All VDD and VSS pins (see Section 2.2

“Decoupling Capacitors”)

• All AVDD and AVSS pins (regardless if ADC module

is not used) (see Section 2.2 “Decoupling

Capacitors”)

•V

CAP (see Section 2.3 “CPU Logic Filter

Capacitor Connection (VCAP)”)

•MCLR

pin (see Section 2.4 “Master Clear (MCLR)

Pin”)

• PGECx/PGEDx pins used for In-Circuit Serial

Programming™ (ICSP™) and debugging purposes

(see Section 2.5 “ICSP Pins”)

• OSC1 and OSC2 pins when external oscillator

source is used (see Section 2.6 “External

Oscillator Pins”)

Additionally, the following pins may be required:

•V

USB3V3 pin is used when utilizing the USB

module. If the USB module is not used, VUSB3V3

must be connected to VDD.

•V

REF+/VREF- pin is used when external voltage

reference for ADC module is implemented

2.2 Decoupling Capacitors

The use of decoupling capacitors on every pair of

power supply pins, such as VDD, VSS, VUSB3V3,

AVDD and AVSS is required.

Consider the following criteria when using decoupling

capacitors:

•Value and type of capacitor: Recommendation of

0.1 µF (100 nF), 10-20V. This capacitor should be a

low-ESR and have resonance frequency in the

range of 20 MHz and higher. It is recommended to

use ceramic capacitors.

•Placement on the printed circuit board: The

decoupling capacitors should be placed as close to

the pins as possible. It is recommended to place the

capacitors on the same side of the board as the

device. If space is constricted, the capacitor can be

placed on another layer on the PCB using a via;

however, ensure that the trace length from the pin to

the capacitor is within one-quarter inch (6 mm) in

length.

•Handling high frequency noise: If the board is

experiencing high frequency noise, above tens of

MHz, add a second ceramic-type capacitor in

parallel to the above described decoupling capaci-

tor. The value of the second capacitor can be in the

range of 0.01 µF to 0.001 µF. Place this second

capacitor next to the primary decoupling capacitor.

In high-speed circuit designs, consider implement-

ing a decade pair of capacitances as close to the

power and ground pins as possible. For example,

0.1 µF in parallel with 0.001 µF.

•Maximizing performance: On the board layout

from the power supply circuit, run the power and

return traces to the decoupling capacitors first, and

then to the device pins. This ensures that the

decoupling capacitors are first in the power chain.

Equally important is to keep the trace length

between the capacitor and the power pins to a

minimum, thereby reducing PCB track inductance.

Note 1: This data sheet summarizes

the features of the

dsPIC33EPXXX(GP/MC/MU)806/810/814

and PIC24EPXXX(GP/GU)810/814 fami-

lies of devices. It is not intended to be a

comprehensive reference source. To

complement the information in this data

sheet, refer to the related section of the

“dsPIC33E/PIC24E Family Reference

Manual”, which is available from the

Microchip web site (www.microchip.com)

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Note: The AVDD and AVSS pins must be

connected independent of the ADC

voltage reference source. The voltage

difference between AVDD and VDD cannot

exceed 300 mV at any time during

operation or start-up.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 32  2009-2012 Microchip Technology Inc.

FIGURE 2-1: RECOMMENDED

MINIMUM CONNECTION

2.2.1 TANK CAPACITORS

On boards with power traces running longer than six

inches in length, it is suggested to use a tank capacitor

for integrated circuits including DSCs to supply a local

power source. The value of the tank capacitor should

be determined based on the trace resistance that con-

nects the power supply source to the device and the

maximum current drawn by the device in the applica-

tion. In other words, select the tank capacitor so that it

meets the acceptable voltage sag at the device. Typical

values range from 4.7 µF to 47 µF.

2.3 CPU Logic Filter Capacitor

Connection (VCAP)

A low-ESR (< 1 Ohms) capacitor is required on the

VCAP pin, which is used to stabilize the voltage

regulator output voltage. The VCAP pin must not be

connected to VDD and must have a capacitor greater

than 4.7 µF (10 µF is recommended), 16V connected

to ground. The type can be ceramic or tantalum. See

Section 32.0 “Electrical Characteristics” for

additional information.

The placement of this capacitor should be close to the

VCAP. It is recommended that the trace length not

exceeds one-quarter inch (6 mm). See Section 29.2

“On-Chip Voltage Regulator” for details.

2.4 Master Clear (MCLR) Pin

The MCLR pin provides two specific device

functions:

• Device Reset

• Device Programming and Debugging

During device programming and debugging, the

resistance and capacitance that can be added to the

pin must be considered. Device programmers and

debuggers drive the MCLR pin. Consequently,

specific voltage levels (VIH and VIL) and fast signal

transitions must not be adversely affected. Therefore,

specific values of R and C will need to be adjusted

based on the application and PCB requirements.

For example, as shown in Figure 2-2, it is

recommended that the capacitor C, be isolated from

the MCLR pin during programming and debugging

operations.

Place the components as shown in Figure 2-2 within

one-quarter inch (6 mm) from the MCLR pin.

FIGURE 2-2: EXAMPLE OF MCLR PIN

CONNECTIONS

dsPIC33EP/

VDD

VSS

VDD

VSS

VDD

AVDD

AVSS

VDD

VSS

0.1 µF

Ceramic

0.1 µF

Ceramic

0.1 µF

Ceramic

0.1 µF

Ceramic

VDD

MCLR

0.1 µF

Ceramic

VCAP

L1(2)

10 µF

Tantalum

Note 1: If the USB module is not used, VUSB3V3 must be

connected to VDD, as shown.

2: As an option, instead of a hard-wired connection, an

inductor (L1) can be substituted between VDD and

AVDD to improve ADC noise rejection. The inductor

impedance should be less than 1 and the inductor

capacity greater than 10 mA.

Where:

fFCNV

--------------=

2LC

-----------------------=

2fC

----------------------





(i.e., ADC conversion rate/2)

VUSB3V3(1)

PIC24EP

Note 1: R 10 k is recommended. A suggested

starting value is 10 k. Ensure that the

MCLR pin VIH and VIL specifications are met.

2: R1  470 will limit any current flowing into

MCLR from the external capacitor C, in the

event of MCLR pin breakdown, due to

Electrostatic Discharge (ESD) or Electrical

Overstress (EOS). Ensure that the MCLR pin

VIH and VIL specifications are met.

R1(2)

R(1)

VDD

MCLR

dsPIC33EP

 2009-2012 Microchip Technology Inc. DS70616G-page 33

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

2.5 ICSP Pins

The PGECx and PGEDx pins are used for ICSP and

debugging purposes. It is recommended to keep the

trace length between the ICSP connector and the ICSP

pins on the device as short as possible. If the ICSP con-

nector is expected to experience an ESD event, a

series resistor is recommended, with the value in the

range of a few tens of Ohms, not to exceed 100 Ohms.

Pull-up resistors, series diodes and capacitors on the

PGECx and PGEDx pins are not recommended as they

will interfere with the programmer/debugger communi-

cations to the device. If such discrete components are

an application requirement, they should be removed

from the circuit during programming and debugging.

Alternatively, refer to the AC/DC characteristics and

timing requirements information in the respective

device Flash programming specification for information

on capacitive loading limits and pin input voltage high

(VIH) and input low (VIL) requirements.

Ensure that the “Communication Channel Select” (i.e.,

PGECx/PGEDx pins) programmed into the device

matches the physical connections for the ICSP to

MPLAB® PICkit™ 3, MPLAB ICD 3, or MPLAB REAL

ICE™.

For more information on MPLAB ICD 3 and MPLAB

REAL ICE connection requirements, refer to the

following documents that are available on the

Microchip web site.

•“Using MPLAB® ICD 3” (poster) DS51765

•“MPLAB® ICD 3 Design Advisory” DS51764

•“MPLAB® REAL ICE™ In-Circuit Emulator User’s

Guide” DS51616

•“Using MPLAB® REAL ICE™ In-Circuit Emulator”

(poster) DS51749

2.6 External Oscillator Pins

Many DSCs have options for at least two oscillators: a

high-frequency primary oscillator and a low-frequency

secondary oscillator. For details, see Section 9.0

“Oscillator Configuration” for details.

The oscillator circuit should be placed on the same

side of the board as the device. Also, place the

oscillator circuit close to the respective oscillator pins,

not exceeding one-half inch (12 mm) distance

between them. The load capacitors should be placed

next to the oscillator itself, on the same side of the

board. Use a grounded copper pour around the

oscillator circuit to isolate them from surrounding

circuits. The grounded copper pour should be routed

directly to the MCU ground. Do not run any signal

traces or power traces inside the ground pour. Also, if

using a two-sided board, avoid any traces on the

other side of the board where the crystal is placed. A

suggested layout is shown in Figure 2-3.

FIGURE 2-3: SUGGESTED PLACEMENT

OF THE OSCILLATOR

CIRCUIT

2.7 Oscillator Value Conditions on

Device Start-up

If the PLL of the target device is enabled and

configured for the device start-up oscillator, the

maximum oscillator source frequency must be limited

to 3 MHz < FIN < 5.5 MHz to comply with device PLL

start-up conditions. This means that if the external

oscillator frequency is outside this range, the

application must start-up in the FRC mode first. The

default PLL settings after a POR with an oscillator

frequency outside this range will violate the device

operating speed.

Once the device powers up, the application firmware

can initialize the PLL SFRs, CLKDIV and PLLDBF to a

suitable value, and then perform a clock switch to the

Oscillator + PLL clock source. Note that clock switching

must be enabled in the device Configuration Word.

2.8 Unused I/Os

Unused I/O pins should be configured as outputs and

driven to a logic-low state.

Alternatively, connect a 1k to 10k resistor between VSS

and unused pins and drive the output to logic low.

Main Oscillator

Guard Ring

Guard Trace

Secondary

Oscillator

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 34  2009-2012 Microchip Technology Inc.

2.9 Application Examples

• Induction heating

• Uninterruptable Power Supplies (UPS)

• DC/AC inverters

• Compressor motor control

• Washing machine 3-phase motor control

• BLDC motor control

• Automotive HVAC, cooling fans, fuel pumps

• Stepper motor control

• Audio and fluid sensor monitoring

• Camera lens focus and stability control

• Speech (playback, hands-free kits, answering

machines, VoIP)

• Consumer audio

• Industrial and building control (security systems

and access control)

• Barcode reading

• Networking: LAN switches, gateways

• Data storage device management

• Smart cards and smart card readers

Examples of typical application connections are shown

in Figure 2-4 through Figure 2-8.

FIGURE 2-4: BOOST CONVERTER IMPLEMENTATION

IPFC

VOUTPUT

ADC Channel ADC Channel

PWM

FET

dsPIC33EP

VINPUT

Comparator

Output

Driver

 2009-2012 Microchip Technology Inc. DS70616G-page 35

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 2-5: SINGLE-PHASE SYNCHRONOUS BUCK CONVERTER

FIGURE 2-6: MULTI-PHASE SYNCHRONOUS BUCK CONVERTER

Comparator

PWM

ADC

Channel

ADC

Channel

5V Output

I5V

12V Input

FET

Driver

dsPIC33EP

Comparator

ADC Channel

Comparator

ADC

Channel

PWM

3.3V Output

12V Input

FET

Driver

FET

Driver

FET

Driver

dsPIC33EP

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 36  2009-2012 Microchip Technology Inc.

FIGURE 2-7: INTERLEAVED PFC

FIGURE 2-8: BEMF VOLTAGE MEASURED USING THE ADC MODULE

VAC

VOUT+

Comparator

PWM

ADC

PWM

|VAC|

k4k3

FET

dsPIC33EP

Driver

VOUT-

ADC Channel

FET

Driver

k1k2

Comparator

Channel

Comparator

3-Phase

Inverter

PWM3H

PWM3L

PWM2H

PWM2L

PWM1H

PWM1L

FLTx Fault

BLDC

dsPIC33EP/PIC24EP

AN3

AN4

AN5

AN2

Demand

Phase Terminal Voltage Feedback

R49 R41 R34 R36

R44

R52

 2009-2012 Microchip Technology Inc. DS70616G-page 37

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

3.0 CPU

The CPU has a 16-bit (data) modified Harvard

architecture with an enhanced instruction set, including

significant support for digital signal processing. The

CPU has a 24-bit instruction word, with a variable

length opcode field. The Program Counter (PC) is

24 bits wide and addresses up to 4M x 24 bits of user

program memory space.

An instruction prefetch mechanism helps maintain

throughput and provides predictable execution. Most

instructions execute in a single-cycle effective execu-

tion rate, with the exception of instructions that change

the program flow, the double-word move (MOV.D)

instruction, PSV accesses and the table instructions.

Overhead free program loop constructs are supported

using the DO and REPEAT instructions, both of which

are interruptible at any point.

3.1 Registers

Devices have sixteen 16-bit working registers in the

programmer’s model. Each of the working registers

can act as a Data, Address or Address Offset register.

The 16th working register (W15) operates as a Soft-

ware Stack Pointer for interrupts and calls. The working

registers, W0 through W3, and selected bits from the

STATUS register, have shadow registers for fast

context saves and restores using a single POP.S or

PUSH.S instruction.

3.2 Instruction Set

The dsPIC33EPXXXMU806/810/814 instruction set

has two classes of instructions: the MCU class of

instructions and the DSP class of instructions. The

PIC24EPXXX(GP/GU)810/814 instruction set has the

MCU class of instructions and does not support DSP

instructions. These two instruction classes are seam-

lessly integrated into the architecture and execute from

a single execution unit. The instruction set includes

many addressing modes and was designed for

optimum C compiler efficiency.

3.3 Data Space Addressing

The Base Data Space can be addressed as 32K words

or 64 Kbytes and is split into two blocks, referred to as

X and Y data memory. Each memory block has its own

independent Address Generation Unit (AGU). The

MCU class of instructions operate solely through the X

memory AGU, which accesses the entire memory map

as one linear data space. On dsPIC33EPXXX(GP/MC/

MU)806/810/814 devices, certain DSP instructions

operate through the X and Y AGUs to support dual

operand reads, which splits the data address space

into two parts. The X and Y data space boundary is

device-specific.

The upper 32 Kbytes of the data space memory map

can optionally be mapped into Program Space at any

16K program word boundary. The program-to-data

space mapping feature, known as Program Space

Visibility (PSV), lets any instruction access Program

Space as if it were data space. Moreover, the Base

Data Space address is used in conjunction with a read

or write page register (DSRPAG or DSWPAG) to form

an Extended Data Space (EDS) address. The EDS can

be addressed as 8M words or 16 Mbytes. Refer to

Section 3. “Data Memory” (DS70595) and Section 4.

“Program Memory” (DS70613) in the “dsPIC33E/

PIC24E Family Reference Manual” for more details on

EDS, PSV and table accesses.

On dsPIC33EPXXX(GP/MC/MU)806/810/814 devices,

overhead-free circular buffers (Modulo Addressing) are

supported in both X and Y address spaces. The

Modulo Addressing removes the software boundary

checking overhead for DSP algorithms. The X AGU

circular addressing can be used with any of the MCU

class of instructions. The X AGU also supports Bit-

Reversed Addressing to greatly simplify input or output

data reordering for radix-2 FFT algorithms.

PIC24EPXXX(GP/GU)810/814 devices do not support

Modulo and Bit-Reversed Addressing.

3.4 Addressing Modes

The CPU supports these addressing modes:

• Inherent (no operand)

• Relative

•Literal

• Memory Direct

• Register Direct

• Register Indirect

Each instruction is associated with a predefined

addressing mode group, depending upon its functional

requirements. As many as six addressing modes are

supported for each instruction.

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this

data sheet, refer to Section 2. “CPU”

(DS70359) in the “dsPIC33E/PIC24E

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 38  2009-2012 Microchip Technology Inc.

FIGURE 3-1: dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814 CPU

BLOCK DIAGRAM

Note 1: This feature or peripheral is only available on dsPIC33EPXXX(MC/MU)806/810/814 devices.

This feature or peripheral is only available on dsPIC33EPXXXMU806/810/814 and PIC24EPXXXGU806/810/814 devices.

PORTA

PORTB

PORTD

PORTC

Power-up

Timer

Oscillator

Start-up Timer

Instruction

Decode and

Control

OSC1/CLKI

MCLR

VDD, VSS

UART1-

Timing

Generation

ECAN1,

PCH

Program Counter

16-Bit ALU

X Data Bus

I2C1,

DCI

PCU

ADC1,

Timers

Input

Capture

Output

Compare

16 16

Divide

Support

Engine(1)

DSP

ROM Latch

Y Data Bus(1)

EA MUX

X RAGU

X WAGU

Y AGU

(1)

AVDD, AVSS

UART4

SPI4

Interrupt

Controller PSV and Table

Data Access

Control Block

Stack

Control

Logic

Loop

Control

Logic

Data LatchData Latch

Y Data

RAM(1) X Data

RAM

Address

Latch

Address

Latch

Control Signals

to Various Blocks

SPI1-

Data Latch

X Address Bus

Y Address Bus

Literal Data

ADC2

Program Memory

Watchdog

Timer

POR/BOR

Address Latch

PMP

Comparator

CRC

RTCC

USB

I2C2

ECAN2

QEI1(1),

PWM(1)

QEI2(1)

(3-Channel)

PORTE

PORTF

PORTG

PORTH

PORTJ

PORTK

Remappable

Pins

OTG(2)

PCL

16 x 16

W Reg Array

 2009-2012 Microchip Technology Inc. DS70616G-page 39

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

3.5 Programmer’s Model

The programmer’s model is shown in Figure 3-2. All

registers in the programmer’s model are memory

mapped and can be manipulated directly by

instructions. Table 3-1 lists a description of each

In addition to the registers contained in the

programmer’s model, all devices in this family

contain control registers for interrupts, while

the dsPIC33EPXXX(GP/MC/MU)806/810/814 devices

contain control registers for Modulo and Bit-reversed

Addressing. These registers are described in

subsequent sections of this document.

All registers associated with the programmer’s model

are memory mapped, as shown in Table 4-1.

TABLE 3-1: PROGRAMMER’S MODEL REGISTER DESCRIPTIONS

W0 through W15 Working Register Array

ACCA, ACCB 40-Bit DSP Accumulators

PC 23-Bit Program Counter

SR ALU and DSP Engine Status register

SPLIM Stack Pointer Limit Value register

TBLPAG Table Memory Page Address register

DSRPAG Extended Data Space (EDS) Read Page register

DSWPAG Extended Data Space (EDS) Write Page register

RCOUNT REPEAT Loop Count register

DCOUNT(1)DO Loop Count register

DOSTARTH(1,2), DOSTARTL(1,2)DO Loop Start Address register (High and Low)

DOENDH(1), DOENDL(1)DO Loop End Address register (High and Low)

CORCON Contains DSP Engine, DO Loop Control and Trap Status bits

Note 1: This register is available on dsPIC33EPXXX(GP/MC/MU)806/810/814 devices only.

2: The DOSTARTH and DOSTARTL registers are read-only.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 40  2009-2012 Microchip Technology Inc.

FIGURE 3-2: PROGRAMMER’S MODEL

NOVZ C

TBLPAG

PC23 PC0

D0D15

Program Counter

Data Table Page Address

Status Register

Working/Address

Registers

DSP Operand

Registers

W0 (WREG)

W10

W11

W12

W13

Frame Pointer/W14

Stack Pointer/W15*

DSP Address

Registers

AD39 AD0

AD31

DSP

Accumulators(1) ACCA

ACCB

DSRPAG

OA(1) OB(1) SA(1) SB(1)

RCOUNT

15 0

Repeat Loop Counter

DCOUNT

15 0

DO Loop Counter and Stack(1)

DOSTART

23 0

DO Loop Start Address and Stack(1)

DOEND DO Loop End Address and Stack(1)

IPL2 IPL1

SPLIM* Stack Pointer Limit

AD15

23 0

SRL

IPL0

PUSH.s and POP.s shadows

Nested DO Stack

OAB(1) SAB(1)

X Data Space Read Page Address

DA(1) DC

DSWPAG X Data Space Write Page Address

Note 1: This feature or bit is available on dsPIC33EPXXX(GP/MC/MU)806/810/814 devices only.

CORCON

15 0

CPU Core Control Register

 2009-2012 Microchip Technology Inc. DS70616G-page 41

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

3.6 CPU Resources

Many useful resources related to the CPU are provided

on the main product page of the Microchip web site for

the devices listed in this data sheet. This product page,

which can be accessed using this link, contains the

latest updates and additional information.

3.6.1 KEY RESOURCES

•See Section 16. “CPU” (DS70359) in the

“dsPIC33E/PIC24E Family Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 42  2009-2012 Microchip Technology Inc.

3.7 CPU Control Registers

R/W-0 R/W-0 R/W-0 R/W-0 R/C-0 R/C-0 R -0 R/W-0

OA(1)OB(1)SA(1,4)SB(1,4)OAB(1)SAB(1)DA(1)DC

bit 15 bit 8

R/W-0(2,3)R/W-0(2,3)R/W-0(2,3)R-0 R/W-0 R/W-0 R/W-0 R/W-0

IPL<2:0> RA N OV Z C

bit 7 bit 0

Legend: U = Unimplemented bit, read as ‘0’

R = Readable bit W = Writable bit C = Clearable bit

-n = Value at POR ‘1’= Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 OA: Accumulator A Overflow Status bit(1)

1 = Accumulator A has overflowed

0 = Accumulator A has not overflowed

bit 14 OB: Accumulator B Overflow Status bit(1)

1 = Accumulator B has overflowed

0 = Accumulator B has not overflowed

bit 13 SA: Accumulator A Saturation ‘Sticky’ Status bit(1,4)

1 = Accumulator A is saturated or has been saturated at some time

0 = Accumulator A is not saturated

bit 12 SB: Accumulator B Saturation ‘Sticky’ Status bit(1,4)

1 = Accumulator B is saturated or has been saturated at some time

0 = Accumulator B is not saturated

bit 11 OAB: OA || OB Combined Accumulator Overflow Status bit(1)

1 = Accumulators A or B have overflowed

0 = Neither Accumulators A or B have overflowed

bit 10 SAB: SA || SB Combined Accumulator ‘Sticky’ Status bit(1)

1 = Accumulators A or B are saturated or have been saturated at some time

0 = Neither Accumulator A or B are saturated

bit 9 DA: DO Loop Active bit(1)

1 = DO loop in progress

0 = DO loop not in progress

bit 8 DC: MCU ALU Half Carry/Borrow bit

1 = A carry-out from the 4th low order bit (for byte-sized data) or 8th low order bit (for word-sized data)

of the result occurred

0 = No carry-out from the 4th low order bit (for byte-sized data) or 8th low order bit (for word-sized

data) of the result occurred

Note 1: This bit is available on dsPIC33EPXXX(GP/MC/MU)806/810/814 devices only.

2: The IPL<2:0> bits are concatenated with the IPL<3> bit (CORCON<3>) to form the CPU Interrupt Priority

Level. The value in parentheses indicates the IPL, if IPL<3> = 1.

3: The IPL<2:0> bits are read-only when NSTDIS = 1 (INTCON1<15>).

4: A data write to the SR register can modify the SA and SB bits by either a data write to SA and SB or by

clearing the SAB bit. To avoid a possible SA or SB bit write race condition, the SA and SB bits should not

be modified using bit operations.

 2009-2012 Microchip Technology Inc. DS70616G-page 43

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

bit 7-5 IPL<2:0>: CPU Interrupt Priority Level Status bits(2,3)

111 = CPU Interrupt Priority Level is 7 (15, user interrupts are disabled)

110 = CPU Interrupt Priority Level is 6 (14)

101 = CPU Interrupt Priority Level is 5 (13)

100 = CPU Interrupt Priority Level is 4 (12)

011 = CPU Interrupt Priority Level is 3 (11)

010 = CPU Interrupt Priority Level is 2 (10)

001 = CPU Interrupt Priority Level is 1 (9)

000 = CPU Interrupt Priority Level is 0 (8)

bit 4 RA: REPEAT Loop Active bit

1 = REPEAT loop in progress

0 = REPEAT loop not in progress

bit 3 N: MCU ALU Negative bit

1 = Result was negative

0 = Result was non-negative (zero or positive)

bit 2 OV: MCU ALU Overflow bit

This bit is used for signed arithmetic (2’s complement). It indicates an overflow of the magnitude that

causes the sign bit to change state.

1 = Overflow occurred for signed arithmetic (in this arithmetic operation)

0 = No overflow occurred

bit 1 Z: MCU ALU Zero bit

1 = An operation that affects the Z bit has set it at some time in the past

0 = The most recent operation that affects the Z bit has cleared it (i.e., a non-zero result)

bit 0 C: MCU ALU Carry/Borrow bit

1 = A carry-out from the Most Significant bit of the result occurred

0 = No carry-out from the Most Significant bit of the result occurred

Note 1: This bit is available on dsPIC33EPXXX(GP/MC/MU)806/810/814 devices only.

2: The IPL<2:0> bits are concatenated with the IPL<3> bit (CORCON<3>) to form the CPU Interrupt Priority

Level. The value in parentheses indicates the IPL, if IPL<3> = 1.

3: The IPL<2:0> bits are read-only when NSTDIS = 1 (INTCON1<15>).

4: A data write to the SR register can modify the SA and SB bits by either a data write to SA and SB or by

clearing the SAB bit. To avoid a possible SA or SB bit write race condition, the SA and SB bits should not

be modified using bit operations.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 44  2009-2012 Microchip Technology Inc.

R/W-0 U-0 R/W-0 R/W-0 R/W-0 R-0 R-0 R-0

VAR — US<1:0>(1)EDT(1,2)DL<2:0>(1)

bit 15 bit 8

R/W-0 R/W-0 R/W-1 R/W-0 R/C-0 R-0 R/W-0 R/W-0

SATA(1)SATB(1)SATDW(1)ACCSAT(1)IPL3(3)SFA RND(1)IF(1)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 VAR: Variable Exception Processing Latency Control bit

1 = Variable exception processing is enabled

0 = Fixed exception processing is enabled

bit 14 Unimplemented: Read as ‘0’

bit 13-12 US<1:0>: DSP Multiply Unsigned/Signed Control bits(1)

11 = Reserved

10 = DSP engine multiplies are mixed-sign

01 = DSP engine multiplies are unsigned

00 = DSP engine multiplies are signed

bit 11 EDT: Early DO Loop Termination Control bit(1,2)

1 = Terminates executing DO loop at end of current loop iteration

0 = No effect

bit 10-8 DL<2:0>: DO Loop Nesting Level Status bits(1)

111 = 7 DO loops are active

•

001 = 1 DO loop is active

000 = 0 DO loops are active

bit 7 SATA: ACCA Saturation Enable bit(1)

1 = Accumulator A saturation is enabled

0 = Accumulator A saturation is disabled

bit 6 SATB: ACCB Saturation Enable bit(1)

1 = Accumulator B saturation is enabled

0 = Accumulator B saturation is disabled

bit 5 SATDW: Data Space Write from DSP Engine Saturation Enable bit(1)

1 = Data space write saturation is enabled

0 = Data space write saturation is disabled

bit 4 ACCSAT: Accumulator Saturation Mode Select bit(1)

1 = 9.31 saturation (super saturation)

0 = 1.31 saturation (normal saturation)

bit 3 IPL3: CPU Interrupt Priority Level Status bit 3(3)

1 = CPU Interrupt Priority Level is greater than 7

0 = CPU Interrupt Priority Level is 7 or less

Note 1: This bit is available on dsPIC33EPXXX(GP/MC/MU)806/810/814 devices only.

2: This bit is always read as ‘0’.

3: The IPL3 bit is concatenated with the IPL<2:0> bits (SR<7:5>) to form the CPU Interrupt Priority Level.

 2009-2012 Microchip Technology Inc. DS70616G-page 45

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

bit 2 SFA: Stack Frame Active Status bit

1 = Stack frame is active; W14 and W15 address 0x0000 to 0xFFFF, regardless of DSRPAG and

DSWPAG values

0 = Stack frame is not active; W14 and W15 address of EDS or Base Data Space

bit 1 RND: Rounding Mode Select bit(1)

1 = Biased (conventional) rounding is enabled

0 = Unbiased (convergent) rounding is enabled

bit 0 IF: Integer or Fractional Multiplier Mode Select bit(1)

1 = Integer mode is enabled for DSP multiply

0 = Fractional mode is enabled for DSP multiply

Note 1: This bit is available on dsPIC33EPXXX(GP/MC/MU)806/810/814 devices only.

2: This bit is always read as ‘0’.

3: The IPL3 bit is concatenated with the IPL<2:0> bits (SR<7:5>) to form the CPU Interrupt Priority Level.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 46  2009-2012 Microchip Technology Inc.

3.8 Arithmetic Logic Unit (ALU)

The ALU is 16 bits wide and is capable of addition,

subtraction, bit shifts and logic operations. Unless

otherwise mentioned, arithmetic operations are two’s

complement in nature. Depending on the operation, the

ALU can affect the values of the Carry (C), Zero (Z),

Negative (N), Overflow (OV) and Digit Carry (DC)

Status bits in the SR register. The C and DC Status bits

operate as Borrow and Digit Borrow bits, respectively,

for subtraction operations.

The ALU can perform 8-bit or 16-bit operations,

depending on the mode of the instruction that is used.

Data for the ALU operation can come from the W

addressing mode of the instruction. Likewise, output

data from the ALU can be written to the W register array

or a data memory location.

Refer to the “16-bit MCU and DSC Programmer’s

Reference Manual” (DS70157) for information on the

SR bits affected by each instruction.

The core CPU incorporates hardware support for both

multiplication and division. This includes a dedicated

hardware multiplier and support hardware for 16-bit

divisor division.

3.8.1 MULTIPLIER

Using the high-speed 17-bit x 17-bit multiplier, the ALU

supports unsigned, signed, or mixed-sign operation in

several MCU multiplication modes:

• 16-bit x 16-bit signed

• 16-bit x 16-bit unsigned

• 16-bit signed x 5-bit (literal) unsigned

• 16-bit signed x 16-bit unsigned

• 16-bit unsigned x 5-bit (literal) unsigned

• 16-bit unsigned x 16-bit signed

• 8-bit unsigned x 8-bit unsigned

3.8.2 DIVIDER

The divide block supports 32-bit/16-bit and 16-bit/16-bit

signed and unsigned integer divide operations with the

following data sizes:

1. 32-bit signed/16-bit signed divide

2. 32-bit unsigned/16-bit unsigned divide

3. 16-bit signed/16-bit signed divide

4. 16-bit unsigned/16-bit unsigned divide

The quotient for all divide instructions ends up in W0

and the remainder in W1. The 16-bit signed and

unsigned DIV instructions can specify any W register

for both the 16-bit divisor (Wn) and any W register

(aligned) pair (W(m + 1):Wm) for the 32-bit dividend.

The divide algorithm takes one cycle per bit of divisor,

so both 32-bit/16-bit and 16-bit/16-bit instructions take

the same number of cycles to execute.

3.9 DSP Engine (dsPIC33EPXXX(GP/

MC/MU)806/810/814 Devices Only)

The DSP engine consists of a high-speed 17-bit x

17-bit multiplier, a 40-bit barrel shifter and a 40-bit

adder/subtracter (with two target accumulators, round

and saturation logic).

The DSP engine can also perform inherent accumula-

tor-to-accumulator operations that require no additional

data. These instructions are: ADD, SUB and NEG.

The DSP engine has options selected through bits in

the CPU Core Control register (CORCON), as listed

below:

• Fractional or integer DSP multiply (IF)

• Signed, unsigned or mixed-sign DSP multiply (US)

• Conventional or convergent rounding (RND)

• Automatic saturation on/off for ACCA (SATA)

• Automatic saturation on/off for ACCB (SATB)

• Automatic saturation on/off for writes to data

memory (SATDW)

• Accumulator Saturation mode selection

(ACCSAT)

TABLE 3-2: DSP INSTRUCTIONS

SUMMARY

Instruction Algebraic

Operation

ACC Write

Back

CLR A = 0 Yes

ED A = (x – y)2No

EDAC A = A + (x – y)2No

MAC A = A + (x • y) Yes

MAC A = A + x2No

MOVSAC No change in A Yes

MPY A = x • y No

MPY A = x2No

MPY.N A = – x • y No

MSC A = A – x • y Yes

 2009-2012 Microchip Technology Inc. DS70616G-page 47

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

4.0 MEMORY ORGANIZATION

The device architecture features separate program and

data memory spaces and buses. This architecture also

allows the direct access of program memory from the

data space during code execution.

4.1 Program Address Space

The device program address memory space is 4M

instructions. The space is addressable by a 24-bit

value derived either from the 23-bit PC during program

execution, or from table operation or data space

remapping as described in Section 4.8 “Interfacing

Program and Data Memory Spaces”.

User application access to the program memory space

is restricted to the lower half of the address range

(0x000000 to 0x7FFFFF). The exception is the use of

TBLRD/TBLWT operations, which use TBLPAG<7> to

permit access to the Configuration bits and Device ID

sections of the configuration memory space.

The device program memory map is shown in

Figure 4-1.

FIGURE 4-1: PROGRAM MEMORY MAP FOR dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 DEVICES(1)

Note: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this data

sheet, refer to Section 4. “Program

Memory” (DS70613) of the “dsPIC33E/

PIC24E Family Reference Manual”, which

is available from the Microchip web site

(www.microchip.com).

0x000000

0x000002

0x7FFFFE

0xF80000

0xF80012

0xF80014

0xFEFFFE

0xFF0000

0xFF0002

0xF7FFFE

0x000004

0x7FFFFC

0x000200

0x0001FE

Configuration Memory Space User Memory Space

Note 1: Memory areas are not shown to scale.

2: The Reset location is controlled by the Reset Target Vector Select bit, RSTPRI (FICD<2>). See Section 29.0 “Special Features”

for more information.

Reset Address

(2)

Device Configuration

User Program

Flash Memory

(87552 instructions)

Registers

DEVID (2 Words)

Unimplemented

(Read ‘

’s)

GOTO

Instruction

(2)

Reserved

Interrupt Vector Table

dsPIC33EP256MU806/810/814 and

Reset Address

(2)

Device Configuration

User Program

Flash Memory

(175104 instructions)

Registers

DEVID (2 Words)

Unimplemented

(Read ‘

’s)

GOTO

Instruction

(2)

Reserved

Interrupt Vector Table

dsPIC33EP512(GP/MC/MU)806/810/814 and

0x055800

0x0557FE

0x02AC00

0x02ABFE

Reserved Reserved

0xFFFFFE

0x7FFFFA

0x7FC000

Flash Memory

Auxiliary Program

PIC24EP256GU810/814 PIC24EP512(GP/GU)806/810/814

GOTO

Instruction

(2)

Flash Memory

0x800000

Auxiliary Program

Reset Address

(2)

GOTO

Instruction

(2)

Reset Address

(2)

Reserved Reserved

Write Latch Write Latch

0xF9FFFE

0xFA0000

0xFA00FE

0xFA0100

Vector

Auxiliary Interrupt Vector

Auxiliary Interrupt

0x7FFFF8

0x7FBFFE

General SegmentAuxiliary Segment

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 48  2009-2012 Microchip Technology Inc.

4.1.1 PROGRAM MEMORY

ORGANIZATION

The program memory space is organized in word-

addressable blocks. Although it is treated as 24 bits

wide, it is more appropriate to think of each address of

the program memory as a lower and upper word, with

the upper byte of the upper word being unimplemented.

The lower word always has an even address, while the

upper word has an odd address (Figure 4-2).

Program memory addresses are always word-aligned

on the lower word and addresses are incremented or

decremented by two during code execution. This

arrangement provides compatibility with data memory

space addressing and makes data in the program

memory space accessible.

4.1.2 INTERRUPT AND TRAP VECTORS

All devices reserve the addresses between 0x00000

and 0x000200 for hard-coded program execution vec-

tors. A hardware Reset vector is provided to redirect

code execution from the default value of the PC on

device Reset to the actual start of code. A GOTO

instruction is programmed by the user application at

address 0x000000 of the primary Flash memory or at

address 0x7FFFFC of the auxiliary Flash memory, with

the actual address for the start of code at address

0x000002 of the primary Flash memory or at address

0x7FFFFE of the auxiliary Flash memory. Reset Target

Vector Select bit (RSTPRI) in the FPOR Configuration

Reset location is used.

A more detailed discussion of the interrupt vector

tables is provided in Section 7.1 “Interrupt Vector

Table”.

FIGURE 4-2: PROGRAM MEMORY ORGANIZATION

0816

PC Address

0x000000

0x000002

0x000004

0x000006

00000000

Program Memory

‘Phantom’ Byte

(read as ‘0’)

least significant word

most significant word

Instruction Width

0x000001

0x000003

0x000005

0x000007

msw

Address (lsw Address)

 2009-2012 Microchip Technology Inc. DS70616G-page 49

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

4.2 Data Address Space

The CPU has a separate 16-bit wide data memory

space. The data space is accessed using separate

Address Generation Units (AGUs) for read and write

operations. The data memory maps are shown in

Figure 4-3, Figure 4-4, Figure 4-5 and Figure 4-6.

All Effective Addresses (EAs) in the data memory space

are 16 bits wide and point to bytes within the data space.

This arrangement gives a Base Data Space address

range of 64 Kbytes or 32K words.

The Base Data Space address is used in conjunction

with a Read or Write Page register (DSRPAG or

DSWPAG) to form an Extended Data Space, which has

a total address range of 16 MBytes.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices implement up

to 56 Kbytes of data memory. If an EA point to a loca-

tion outside of this area, an all-zero word or byte is

returned.

4.2.1 DATA SPACE WIDTH

The data memory space is organized in byte-

addressable, 16-bit wide blocks. Data is aligned in

data memory and registers as 16-bit words, but all data

space EAs resolve to bytes. The Least Significant

Bytes (LSBs) of each word have even addresses, while

the Most Significant Bytes (MSBs) have odd

addresses.

4.2.2 DATA MEMORY ORGANIZATION

AND ALIGNMENT

To maintain backward compatibility with PIC® MCU

devices and improve data space memory usage

efficiency, the device instruction set supports both word

and byte operations. As a consequence of byte

accessibility, all Effective Address calculations are

internally scaled to step through word-aligned memory.

For example, the core recognizes that Post-Modified

value of Ws + 1 for byte operations and Ws + 2 for word

operations.

A data byte read, reads the complete word that

contains the byte, using the LSb of any EA to determine

which byte to select. The selected byte is placed onto

the LSB of the data path. That is, data memory and

registers are organized as two parallel byte-wide

entities with shared (word) address decode but

separate write lines. Data byte writes only write to the

corresponding side of the array or register that matches

the byte address.

All word accesses must be aligned to an even address.

Misaligned word data fetches are not supported, so

care must be taken when mixing byte and word

operations, or translating from 8-bit MCU code. If a

misaligned read or write is attempted, an address error

trap is generated. If the error occurred on a read, the

instruction underway is completed. If the error occurred

on a write, the instruction is executed but the write does

not occur. In either case, a trap is then executed,

allowing the system and/or user application to examine

the machine state prior to execution of the address

Fault.

All byte loads into any W register are loaded into the

LSB. The MSB is not modified.

A Sign-Extend instruction (SE) is provided to allow user

applications to translate 8-bit signed data to 16-bit

signed values. Alternatively, for 16-bit unsigned data,

user applications can clear the MSB of any W register

by executing a Zero-Extend (ZE) instruction on the

appropriate address.

4.2.3 SFR SPACE

The first 4 Kbytes of the Near Data Space, from 0x0000

to 0x0FFF, is primarily occupied by Special Function

Registers (SFRs). These are used by the core and

peripheral modules for controlling the operation of the

device.

SFRs are distributed among the modules that they

control and are generally grouped together by module.

Much of the SFR space contains unused addresses;

these are read as ‘0’.

4.2.4 NEAR DATA SPACE

The 8-Kbyte area between 0x0000 and 0x1FFF is

referred to as the Near Data Space. Locations in this

space are directly addressable through a 13-bit abso-

lute address field within all memory direct instructions.

Additionally, the whole data space is addressable using

MOV instructions, which support Memory Direct

Addressing mode with a 16-bit address field, or by

using Indirect Addressing mode using a working

Note: The actual set of peripheral features and

interrupts varies by the device. Refer to

the corresponding device tables and

pinout diagrams for device-specific

information.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 50  2009-2012 Microchip Technology Inc.

FIGURE 4-3: DATA MEMORY MAP FOR dsPIC33EP512(GP/MC/MU)806/810/814 DEVICES

WITH 52-KBYTE RAM

0x0000

0x0FFE

SFR Space

0xFFFE

16 Bits

LSBMSB

0xFFFF

X Data

Optionally

Mapped

into Program

Memory

Unimplemented (X)

0x1000

4-Kbyte

SFR Space

0x9000

0x8FFE

0xDFFE

0xE000

52-Kbyte

SRAM Space

Near Data

Space

8-Kbyte

0xCFFE

0xD000

LSB

Address

MSB

Address

0x0000

0x0FFF

0x1001

0x9001

0x8FFF

0xDFFF

0xE001

0xCFFF

0xD001

0x8001 0x8000

0x1FFE

0x2000

0x1FFF

0x2001

0x7FFE

0x7FFF

DPSRAM (Y)

Y Data RAM (Y)

X Data RAM (X)

Far

Data

Space

 2009-2012 Microchip Technology Inc. DS70616G-page 51

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 4-4: DATA MEMORY MAP FOR PIC24EP512(GP/GU)806/810/814 DEVICES

WITH 52-KBYTE RAM

0x0000

0x0FFE

SFR Space

0xFFFE

16 Bits

LSBMSB

0xFFFF

X Data

Optionally

Mapped

into Program

Memory

Unimplemented (X)

0x1000

4-Kbyte

SFR Space

0xDFFE

0xE000

52-Kbyte

SRAM Space

Near Data

Space

8-Kbyte

0xCFFE

0xD000

LSB

Address

MSB

Address

0x0000

0x0FFF

0x1001

0xDFFF

0xE001

0xCFFF

0xD001

0x8001 0x8000

0x1FFE

0x2000

0x1FFF

0x2001

0x7FFE

0x7FFF

DMA Dual Port RAM (X)

X Data RAM (X)

Far

Data

Space

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 52  2009-2012 Microchip Technology Inc.

FIGURE 4-5: DATA MEMORY MAP FOR dsPIC33EP256MU806/810/814 DEVICES

WITH 28-KBYTE RAM

0x0000

0x0FFE

0x4FFE

0xFFFE

LSB

Address

16 Bits

LSBMSB

MSB

Address

0x0001

0x0FFF

0x4FFF

0xFFFF

Optionally

Mapped

into Program

Memory

0x7FFF 0x7FFE

0x1001 0x1000

0x5001 0x5000

4-Kbyte

SFR Space

28-Kbyte

SRAM Space

0x80000x8001

0x6FFE

0x7000

0x6FFF

0x7001

Space

Near Data

8-Kbyte

SFR Space

X Data RAM (X)

X Data

Unimplemented (X)

DMA Dual Port RAM (Y)

Y Data RAM (Y)

0x1FFE

0x2000

0x1FFF

0x2001

Far

Data

Space

 2009-2012 Microchip Technology Inc. DS70616G-page 53

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 4-6: DATA MEMORY MAP FOR PIC24EP256GU810/814 DEVICES

WITH 28-KBYTE RAM

0x0000

0x0FFE

0xFFFE

LSB

Address

16 Bits

LSBMSB

MSB

Address

0x0001

0x0FFF

0xFFFF

Optionally

Mapped

into Program

Memory

0x7FFF 0x7FFE

0x1001 0x1000

4-Kbyte

SFR Space

28-Kbyte

SRAM Space

0x80000x8001

0x6FFE

0x7000

0x6FFF

0x7001

Space

Near Data

8-Kbyte

SFR Space

X Data RAM (X)

X Data

Unimplemented (X)

DMA Dual Port RAM

0x1FFE

0x2000

0x1FFF

0x2001

Far

Data

Space

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 54  2009-2012 Microchip Technology Inc.

4.2.5 X AND Y DATA SPACES

The dsPIC33EPXXX(GP/MC/MU)806/810/814 core

has two data spaces, X and Y. These data spaces can

be considered either separate (for some DSP

instructions), or as one unified linear address range (for

MCU instructions). The data spaces are accessed

using two Address Generation Units (AGUs) and

separate data paths. This feature allows certain

instructions to concurrently fetch two words from RAM,

thereby enabling efficient execution of DSP algorithms

such as Finite Impulse Response (FIR) filtering and

Fast Fourier Transform (FFT).

The PIC24EPXXX(GP/GU)806/810/814 devices do not

have a Y data space and a Y AGU. For these devices,

the entire data space is treated as X data space.

The X data space is used by all instructions and

supports all addressing modes. X data space has

separate read and write data buses. The X read data

bus is the read data path for all instructions that view

data space as combined X and Y address space. It is

also the X data prefetch path for the dual operand DSP

instructions (MAC class).

The Y data space is used in concert with the X data

space by the MAC class of instructions (CLR, ED,

EDAC, MAC, MOVSAC, MPY, MPY.N and MSC) to provide

two concurrent data read paths.

Both the X and Y data spaces support Modulo

Addressing mode for all instructions, subject to

addressing mode restrictions. Bit-Reversed

Addressing mode is only supported for writes to X data

space. Modulo Addressing and Bit-Reversed

Addressing are not present in PIC24EPXXX(GP/

GU)806/810/814 devices.

All data memory writes, including in DSP instructions,

view data space as combined X and Y address space.

The boundary between the X and Y data spaces is

device-dependent and is not user-programmable.

4.2.6 DMA RAM

Each dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 device contains

4 Kbytes of dual ported DMA RAM located at the end

of Y data RAM and is part of Y data space. Memory

locations in the DMA RAM space are accessible simul-

taneously by the CPU and the DMA Controller module.

DMA RAM is utilized by the DMA controller to store

data to be transferred to various peripherals using

DMA, as well as data transferred from various periph-

erals using DMA. The DMA RAM can be accessed by

the DMA controller without having to steal cycles from

the CPU.

When the CPU and the DMA controller attempt to

concurrently write to the same DMA RAM location, the

hardware ensures that the CPU is given precedence in

accessing the DMA RAM location. Therefore, the DMA

RAM provides a reliable means of transferring DMA

data without ever having to stall the CPU.

4.3 Program Memory Resources

Many useful resources related to the Program Memory

are provided on the main product page of the Microchip

web site for the devices listed in this data sheet. This

product page, which can be accessed using this link,

contains the latest updates and additional information.

4.3.1 KEY RESOURCES

• Section 4. “Program Memory” (DS70612) in the

“dsPIC33E/PIC24E Family Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

4.4 Special Function Register Maps

Table 4-1 through Ta bl e 4 -72 provide mapping tables

for all Special Function Registers (SFRs).

Note 1: DMA RAM can be used for general

purpose data storage if the DMA function

is not required in an application.

2: On PIC24EPXXX(GP/GU)806/810/814

devices, DMA RAM is located at the end

of X data RAM and is part of X data

space.

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

 2009-2012 Microchip Technology Inc. DS70616G-page 55

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-1: CPU CORE REGISTER MAP FOR dsPIC33EPXXX(GP/MC/MU)806/810/814 DEVICES ONLY

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

W0 0000 W0 (WREG) 0000

W1 0002 W1 0000

W2 0004 W2 0000

W3 0006 W3 0000

W4 0008 W4 0000

W5 000A W5 0000

W6 000C W6 0000

W7 000E W7 0000

W8 0010 W8 0000

W9 0012 W9 0000

W10 0014 W10 0000

W11 0016 W11 0000

W12 0018 W12 0000

W13 001A W13 0000

W14 001C W14 0000

W15 001E W15 1000

SPLIM 0020 SPLIM 0000

ACCAL 0022 ACCAL 0000

ACCAH 0024 ACCAH 0000

ACCAU 0026 Sign-Extension of ACCA<39> ACCAU 0000

ACCBL 0028 ACCBL 0000

ACCBH 002A ACCBH 0000

ACCBU 002C Sign-Extension of ACCB<39> ACCBU 0000

PCL 002E PCL —0000

PCH 0030 —————————PCH0000

DSRPAG 0032 ——————DSRPAG0001

DSWPAG 0034 ———————DSWPAG0001

RCOUNT 0036 RCOUNT 0000

DCOUNT 0038 DCOUNT 0000

DOSTARTL 003A DOSTARTL —0000

DOSTARTH 003C ——————————DOSTARTH0000

DOENDL 003E DOENDL —0000

DOENDH 0040 —————————— DOENDH 0000

Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 56  2009-2012 Microchip Technology Inc.

SR 0042 OA OB SA SB OAB SAB DA DC IPL2 IPL1 IPL0 RA N OV Z C 0000

CORCON 0044 VAR — US<1:0> EDT DL<2:0> SATA SATB SATDW ACCSAT IPL3 SFA RND IF 0020

MODCON 0046 XMODEN YMODEN —— BWM<3:0> YWM<3:0> XWM<3:0> 0000

XMODSRT 0048 XMODSRT<15:1> 00000

XMODEND 004A XMODEND<15:1> 10001

YMODSRT 004C YMODSRT<15:1> 00000

YMODEND 004E YMODEND<15:1> 10001

XBREV 0050 BREN XBREV<14:0> 0000

DISICNT 0052 — — DISICNT<13:0> 0000

TBLPAG 0054 ———————— TBLPAG<7:0> 0000

MSTRPR 0058 MSTRPR<15:0> 0000

TABLE 4-1: CPU CORE REGISTER MAP FOR dsPIC33EPXXX(GP/MC/MU)806/810/814 DEVICES ONLY (CONTINUED)

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 57

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-2: CPU CORE REGISTER MAP FOR PIC24EPXXX(GP/GU)810/814 DEVICES ONLY

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

W0 0000 W0 (WREG) 0000

W1 0002 W1 0000

W2 0004 W2 0000

W3 0006 W3 0000

W4 0008 W4 0000

W5 000A W5 0000

W6 000C W6 0000

W7 000E W7 0000

W8 0010 W8 0000

W9 0012 W9 0000

W10 0014 W10 0000

W11 0016 W11 0000

W12 0018 W12 0000

W13 001A W13 0000

W14 001C W14 0000

W15 001E W15 1000

SPLIM 0020 SPLIM 0000

PCL 002E PCL —0000

PCH 0030 — — — — — — — — —PCH0000

DSRPAG 0032 — — — — — — DSRPAG<9:0> 0001

DSWPAG 0034 — — — — — — — DSWPAG<8:0> 0001

RCOUNT 0036 RCOUNT<15:0> 0000

SR 0042 — — — — — — — DC IPL2 IPL1 IPL0 RA N OV Z C 0000

CORCON 0044 VAR — — — — — — — — — — —IPL3SFA— — 0020

DISICNT 0052 — — DISICNT<13:0> 0000

TBLPAG 0054 — — — — — — — — TBLPAG<7:0> 0000

MSTRPR 0058 MSTRPR<15:0> 0000

Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 58  2009-2012 Microchip Technology Inc.

TABLE 4-3: INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33EPXXXMU814 DEVICES ONLY

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

IFS0 0800 NVMIF DMA1IF AD1IF U1TXIF U1RXIF SPI1IF SPI1EIF T3IF T2IF OC2IF IC2IF DMA0IF T1IF OC1IF IC1IF INT0IF

0000

IFS1 0802 U2TXIF U2RXIF INT2IF T5IF T4IF OC4IF OC3IF DMA2IF IC8IF IC7IF AD2IF INT1IF CNIF CMIF MI2C1IF SI2C1IF

0000

IFS2 0804 T6IF DMA4IF PMPIF OC8IF OC7IF OC6IF OC5IF IC6IF IC5IF IC4IF IC3IF DMA3IF C1IF C1RXIF SPI2IF SPI2EIF

0000

IFS3 0806 — RTCIF DMA5IF DCIIF DCIEIF QEI1IF PSEMIF C2IF C2RXIF INT4IF INT3IF T9IF T8IF MI2C2IF SI2C2IF T7IF

0000

IFS4 0808 — — — —QEI2IF— PSESMIF — C2TXIF C1TXIF DMA7IF DMA6IF CRCIF U2EIF U1EIF —

0000

IFS5 080A PWM2IF PWM1IF IC9IF OC9IF SPI3IF SPI3EIF U4TXIF U4RXIF U4EIF USB1IF —— U3TXIF U3RXIF U3EIF —

0000

IFS6 080C — — — — — — — — — — — PWM7IF PWM6IF PWM5IF PWM4IF PWM3IF

0000

IFS7 080E IC11IF OC11IF IC10IF OC10IF SPI4IF SPI4EIF DMA11IF DMA10IF DMA9IF DMA8IF — — — — — —

0000

IFS8 0810 — ICDIF IC16IF OC16IF IC15IF OC15IF IC14IF OC14IF IC13IF OC13IF — DMA14IF DMA13IF DMA12IF IC12IF OC12IF

0000

IEC0 0820 NVMIE DMA1IE AD1IE U1TXIE U1RXIE SPI1IE SPI1EIE T3IE T2IE OC2IE IC2IE DMA0IE T1IE OC1IE IC1IE INT0IE

0000

IEC1 0822 U2TXIE U2RXIE INT2IE T5IE T4IE OC4IE OC3IE DMA2IE IC8IE IC7IE AD2IE INT1IE CNIE CMIE MI2C1IE SI2C1IE

0000

IEC2 0824 T6IE DMA4IE PMPIE OC8IE OC7IE OC6IE OC5IE IC6IE IC5IE IC4IE IC3IE DMA3IE C1IE C1RXIE SPI2IE SPI2EIE

0000

IEC3 0826 — RTCIE DMA5IE DCIIE DCIEIE QEI1IE PSEMIE C2IE C2RXIE INT4IE INT3IE T9IE T8IE MI2C2IE SI2C2IE T7IE

0000

IEC4 0828 — — — —QEI2IE— PSESMIE — C2TXIE C1TXIE DMA7IE DMA6IE CRCIE U2EIE U1EIE —

0000

IEC5 082A PWM2IE PWM1IE IC9IE OC9IE SPI3IE SPI3EIE U4TXIE U4RXIE U4EIE USB1IE —— U3TXIE U3RXIE U3EIE —

0000

IEC6 082C — — — — — — — — — — — PWM7IE PWM6IE PWM5IE PWM4IE PWM3IE

0000

IEC7 082E IC11IE OC11IE IC10IE OC10IE SPI4IE SPI4EIE DMA11IE DMA10IE DMA9IE DMA8IE — — — — — —

0000

IEC8 0830 — ICDIE IC16IE OC16IE IC15IE OC15IE IC14IE OC14IE IC13IE OC13IE — DMA14IE DMA13IE DMA12IE IC12IE OC12IE

0000

IPC0 0840 — T1IP<2:0> —OC1IP<2:0> —IC1IP<2:0>—INT0IP<2:0>

4444

IPC1 0842 — T2IP<2:0> —OC2IP<2:0> —IC2IP<2:0>— DMA0IP<2:0>

4444

IPC2 0844 — U1RXIP<2:0> — SPI1IP<2:0> —SPI1EIP<2:0>—T3IP<2:0>

4444

IPC3 0846 — NVMIP<2:0> — DMA1IP<2:0> —AD1IP<2:0>— U1TXIP<2:0>

4444

IPC4 0848 —CNIP<2:0> —CMIP<2:0> — MI2C1IP<2:0> — SI2C1IP<2:0>

4444

IPC5 084A — IC8IP<2:0> — IC7IP<2:0> —AD2IP<2:0>—INT1IP<2:0>

4444

IPC6 084C — T4IP<2:0> —OC4IP<2:0> —OC3IP<2:0>— DMA2IP<2:0>

4444

IPC7 084E — U2TXIP<2:0> — U2RXIP<2:0> — INT2IP<2:0> —T5IP<2:0>

4444

IPC8 0850 — C1IP<2:0> — C1RXIP<2:0> — SPI2IP<2:0> —SPI2EIP<2:0>

4444

IPC9 0852 — IC5IP<2:0> — IC4IP<2:0> —IC3IP<2:0>— DMA3IP<2:0>

4444

IPC10 0854 —OC7IP<2:0> —OC6IP<2:0> —OC5IP<2:0>—IC6IP<2:0>

4444

IPC11 0856 — T6IP<2:0> — DMA4IP<2:0> — PMPIP<2:0> — OC8IP<2:0>

4444

IPC12 0858 — T8IP<2:0> — MI2C2IP<2:0> — SI2C2IP<2:0> —T7IP<2:0>

4444

IPC13 085A C2RXIP<2:0> — INT4IP<2:0> — INT3IP<2:0> —T9IP<2:0>

4444

IPC14 085C —DCIEIP<2:0> — QEI1IP<2:0> — PSEMIP<2:0> — C2IP<2:0>

4444

IPC15 085E — — — — —RTCIP<2:0> — DMA5IP<2:0> — DCIIP<2:0>

0444

Legend:

— = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 59

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

IPC16 0860 —CRCIP<2:0> — U2EIP<2:0> —U1EIP<2:0>— — — —

4440

IPC17 0862 — C2TXIP<2:0> — C1TXIP<2:0> — DMA7IP<2:0> — DMA6IP<2:0>

4444

IPC18 0864 — QEI2IP<2:0> — — — — — PSESMIP<2:0> — — — —

4040

IPC20 0868 — U3TXIP<2:0> — U3RXIP<2:0> —U3EIP<2:0>— — — —

4440

IPC21 086A —U4EIP<2:0> — USB1IP<2:0> — — — — — — — —

4400

IPC22 086C — SPI3IP<2:0> —SPI3EIP<2:0> — U4TXIP<2:0> — U4RXIP<2:0>

4444

IPC23 086E — PWM2IP<2:0> — PWM1IP<2:0> —IC9IP<2:0>— OC9IP<2:0>

4444

IPC24 0870 — PWM6IP<2:0> — PWM5IP<2:0> — PWM4IP<2:0> —PWM3IP<2:0>

4444

IPC25 0872 — — — — — — — — — — — — —PWM7IP<2:0>

0004

IPC29 087A — DMA9IP<2:0> — DMA8IP<2:0> — — — — — — — —

4400

IPC30 087C — SPI4IP<2:0> —SPI4EIP<2:0> — DMA11IP<2:0> — DMA10IP<2:0>

4444

IPC31 087E — IC11IP<2:0> — OC11IP<2:0> — IC10IP<2:0> — OC10IP<2:0>

4444

IPC32 0880 — DMA13IP<2:0> — DMA12IP<2:0> — IC12IP<2:0> — OC12IP<2:0>

4444

IPC33 0882 — IC13IP<2:0> — OC13IP<2:0> — — — — — DMA14IP<2:0>

4404

IPC34 0884 — IC15IP<2:0> — OC15IP<2:0> — IC14IP<2:0> — OC14IP<2:0>

4444

IPC35 0886 — — — — —ICDIP<2:0> — IC16IP<2:0> — OC16IP<2:0>

0444

INTCON1 08C0 NSTDIS OVAERR OVBERR COVAERR COVBERR OVATE OVBTE COVTE SFTACERR DIV0ERR DMACERR MATHERR ADDRERR STKERR OSCFAIL —

0000

INTCON2 08C2 GIE DISI SWTRAP — — — — — — — — INT4EP INT3EP INT2EP INT1EP INT0EP

8000

INTCON3 08C4 — — — — — — — — — UAE DAE DOOVR — — — —

0000

INTCON4 08C6 — — — — — — — — — — — — — — —SGHT

0000

INTTREG 08C8 — — — — ILR<3:0> VECNUM<7:0>

0000

TABLE 4-3: INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33EPXXXMU814 DEVICES ONLY (CONTINUED)

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend:

— = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 60  2009-2012 Microchip Technology Inc.

TABLE 4-4: INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33EPXXXMU810 DEVICES ONLY

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

IFS0 0800 NVMIF DMA1IF AD1IF U1TXIF U1RXIF SPI1IF SPI1EIF T3IF T2IF OC2IF IC2IF DMA0IF T1IF OC1IF IC1IF INT0IF

0000

IFS1 0802 U2TXIF U2RXIF INT2IF T5IF T4IF OC4IF OC3IF DMA2IF IC8IF IC7IF AD2IF INT1IF CNIF CMIF MI2C1IF SI2C1IF

0000

IFS2 0804 T6IF DMA4IF PMPIF OC8IF OC7IF OC6IF OC5IF IC6IF IC5IF IC4IF IC3IF DMA3IF C1IF C1RXIF SPI2IF SPI2EIF

0000

IFS3 0806 — RTCIF DMA5IF DCIIF DCIEIF QEI1IF PSEMIF C2IF C2RXIF INT4IF INT3IF T9IF T8IF MI2C2IF SI2C2IF T7IF

0000

IFS4 0808 — — — —QEI2IF— PSESMIF — C2TXIF C1TXIF DMA7IF DMA6IF CRCIF U2EIF U1EIF —

0000

IFS5 080A PWM2IF PWM1IF IC9IF OC9IF SPI3IF SPI3EIF U4TXIF U4RXIF U4EIF USB1IF —— U3TXIF U3RXIF U3EIF —

0000

IFS6 080C — — — — — — — — — — — — PWM6IF PWM5IF PWM4IF PWM3IF

0000

IFS7 080E IC11IF OC11IF IC10IF OC10IF SPI4IF SPI4EIF DMA11IF DMA10IF DMA9IF DMA8IF — — — — — —

0000

IFS8 0810 — ICDIF IC16IF OC16IF IC15IF OC15IF IC14IF OC14IF IC13IF OC13IF — DMA14IF DMA13IF DMA12IF IC12IF OC12IF

0000

IEC0 0820 NVMIE DMA1IE AD1IE U1TXIE U1RXIE SPI1IE SPI1EIE T3IE T2IE OC2IE IC2IE DMA0IE T1IE OC1IE IC1IE INT0IE

0000

IEC1 0822 U2TXIE U2RXIE INT2IE T5IE T4IE OC4IE OC3IE DMA2IE IC8IE IC7IE AD2IE INT1IE CNIE CMIE MI2C1IE SI2C1IE

0000

IEC2 0824 T6IE DMA4IE PMPIE OC8IE OC7IE OC6IE OC5IE IC6IE IC5IE IC4IE IC3IE DMA3IE C1IE C1RXIE SPI2IE SPI2EIE

0000

IEC3 0826 — RTCIE DMA5IE DCIIE DCIEIE QEI1IE PSEMIE C2IE C2RXIE INT4IE INT3IE T9IE T8IE MI2C2IE SI2C2IE T7IE

0000

IEC4 0828 — — — —QEI2IE— PSESMIE — C2TXIE C1TXIE DMA7IE DMA6IE CRCIE U2EIE U1EIE —

0000

IEC5 082A PWM2IE PWM1IE IC9IE OC9IE SPI3IE SPI3EIE U4TXIE U4RXIE U4EIE USB1IE —— U3TXIE U3RXIE U3EIE —

0000

IEC6 082C — — — — — — — — — — — — PWM6IE PWM5IE PWM4IE PWM3IE

0000

IEC7 082E IC11IE OC11IE IC10IE OC10IE SPI4IE SPI4EIE DMA11IE DMA10IE DMA9IE DMA8IE — — — — — —

0000

IEC8 0830 — ICDIE IC16IE OC16IE IC15IE OC15IE IC14IE OC14IE IC13IE OC13IE — DMA14IE DMA13IE DMA12IE IC12IE OC12IE

0000

IPC0 0840 — T1IP<2:0> —OC1IP<2:0> — IC1IP<2:0> — INT0IP<2:0>

4444

IPC1 0842 — T2IP<2:0> —OC2IP<2:0> — IC2IP<2:0> — DMA0IP<2:0>

4444

IPC2 0844 — U1RXIP<2:0> — SPI1IP<2:0> — SPI1EIP<2:0> — T3IP<2:0>

4444

IPC3 0846 —NVMIP<2:0> — DMA1IP<2:0> —AD1IP<2:0>— U1TXIP<2:0>

4444

IPC4 0848 — CNIP<2:0> — CMIP<2:0> — MI2C1IP<2:0> — SI2C1IP<2:0>

4444

IPC5 084A —IC8IP<2:0> —IC7IP<2:0> —AD2IP<2:0>— INT1IP<2:0>

4444

IPC6 084C — T4IP<2:0> —OC4IP<2:0> —OC3IP<2:0>— DMA2IP<2:0>

4444

IPC7 084E — U2TXIP<2:0> — U2RXIP<2:0> — INT2IP<2:0> — T5IP<2:0>

4444

IPC8 0850 — C1IP<2:0> — C1RXIP<2:0> — SPI2IP<2:0> —SPI2EIP<2:0>

4444

IPC9 0852 —IC5IP<2:0> —IC4IP<2:0> — IC3IP<2:0> — DMA3IP<2:0>

4444

IPC10 0854 — OC7IP<2:0> —OC6IP<2:0> —OC5IP<2:0>—IC6IP<2:0>

4444

IPC11 0856 — T6IP<2:0> — DMA4IP<2:0> — PMPIP<2:0> — OC8IP<2:0>

4444

IPC12 0858 — T8IP<2:0> — MI2C2IP<2:0> — SI2C2IP<2:0> — T7IP<2:0>

4444

IPC13 085A C2RXIP<2:0> — INT4IP<2:0> — INT3IP<2:0> — T9IP<2:0>

4444

IPC14 085C — DCIEIP<2:0> — QEI1IP<2:0> —PSEMIP<2:0>—C2IP<2:0>

4444

IPC15 085E — — — — —RTCIP<2:0> — DMA5IP<2:0> — DCIIP<2:0>

0444

Legend:

— = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 61

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

IPC16 0860 —CRCIP<2:0> —U2EIP<2:0> —U1EIP<2:0>— — — —

4440

IPC17 0862 — C2TXIP<2:0> — C1TXIP<2:0> — DMA7IP<2:0> — DMA6IP<2:0>

4444

IPC18 0864 — QEI2IP<2:0> — — — — — PSESMIP<2:0> — — — —

4040

IPC20 0868 — U3TXIP<2:0> — U3RXIP<2:0> —U3EIP<2:0>— — — —

4440

IPC21 086A —U4EIP<2:0> — USB1IP<2:0> — — — — — — — —

4400

IPC22 086C — SPI3IP<2:0> —SPI3EIP<2:0> — U4TXIP<2:0> — U4RXIP<2:0>

4444

IPC23 086E — PWM2IP<2:0> — PWM1IP<2:0> — IC9IP<2:0> — OC9IP<2:0>

4444

IPC24 0870 — PWM6IP<2:0> — PWM5IP<2:0> — PWM4IP<2:0> —PWM3IP<2:0>

4444

IPC29 087A — DMA9IP<2:0> — DMA8IP<2:0> — — — — — — — —

4400

IPC30 087C — SPI4IP<2:0> —SPI4EIP<2:0> — DMA11IP<2:0> — DMA10IP<2:0>

4444

IPC31 087E — IC11IP<2:0> — OC11IP<2:0> — IC10IP<2:0> — OC10IP<2:0>

4444

IPC32 0880 — DMA13IP<2:0> —DMA12IP<2:0> — IC12IP<2:0> — OC12IP<2:0>

4444

IPC33 0882 — IC13IP<2:0> — OC13IP<2:0> — — — — — DMA14IP<2:0>

4404

IPC34 0884 — IC15IP<2:0> — OC15IP<2:0> — IC14IP<2:0> — OC14IP<2:0>

4444

IPC35 0886 — — — — —ICDIP<2:0> — IC16IP<2:0> — OC16IP<2:0>

0444

INTCON1 08C0 NSTDIS OVAERR OVBERR COVAERR COVBERR OVATE OVBTE COVTE SFTACERR DIV0ERR DMACERR MATHERR ADDRERR STKERR OSCFAIL —

0000

INTCON2 08C2 GIE DISI SWTRAP — — — — — — — — INT4EP INT3EP INT2EP INT1EP INT0EP

8000

INTCON3 08C4 — — — — — — — — — UAE DAE DOOVR — — — —

0000

INTCON4 08C6 — — — — — — — — — — — — — — —SGHT

0000

INTTREG 08C8 — — — — — ILR<3:0> VECNUM<7:0>

0000

TABLE 4-4: INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33EPXXXMU810 DEVICES ONLY (CONTINUED)

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend:

— = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 62  2009-2012 Microchip Technology Inc.

TABLE 4-5: INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33EPXXXMU806 DEVICES ONLY

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

IFS0 0800 NVMIF DMA1IF AD1IF U1TXIF U1RXIF SPI1IF SPI1EIF T3IF T2IF OC2IF IC2IF DMA0IF T1IF OC1IF IC1IF INT0IF

0000

IFS1 0802 U2TXIF U2RXIF INT2IF T5IF T4IF OC4IF OC3IF DMA2IF IC8IF IC7IF AD2IF INT1IF CNIF CMIF MI2C1IF SI2C1IF

0000

IFS2 0804 T6IF DMA4IF PMPIF OC8IF OC7IF OC6IF OC5IF IC6IF IC5IF IC4IF IC3IF DMA3IF C1IF C1RXIF SPI2IF SPI2EIF

0000

IFS3 0806 — RTCIF DMA5IF DCIIF DCIEIF QEI1IF PSEMIF C2IF C2RXIF INT4IF INT3IF T9IF T8IF MI2C2IF SI2C2IF T7IF

0000

IFS4 0808 — — — —QEI2IF— PSESMIF — C2TXIF C1TXIF DMA7IF DMA6IF CRCIF U2EIF U1EIF —

0000

IFS5 080A PWM2IF PWM1IF IC9IF OC9IF SPI3IF SPI3EIF U4TXIF U4RXIF U4EIF USB1IF —— U3TXIF U3RXIF U3EIF —

0000

IFS6 080C — — — — — — — — — — — — — — PWM4IF PWM3IF

0000

IFS7 080E IC11IF OC11IF IC10IF OC10IF SPI4IF SPI4EIF DMA11IF DMA10IF DMA9IF DMA8IF — — — — — —

0000

IFS8 0810 — ICDIF IC16IF OC16IF IC15IF OC15IF IC14IF OC14IF IC13IF OC13IF — DMA14IF DMA13IF DMA12IF IC12IF OC12IF

0000

IEC0 0820 NVMIE DMA1IE AD1IE U1TXIE U1RXIE SPI1IE SPI1EIE T3IE T2IE OC2IE IC2IE DMA0IE T1IE OC1IE IC1IE INT0IE

0000

IEC1 0822 U2TXIE U2RXIE INT2IE T5IE T4IE OC4IE OC3IE DMA2IE IC8IE IC7IE AD2IE INT1IE CNIE CMIE MI2C1IE SI2C1IE

0000

IEC2 0824 T6IE DMA4IE PMPIE OC8IE OC7IE OC6IE OC5IE IC6IE IC5IE IC4IE IC3IE DMA3IE C1IE C1RXIE SPI2IE SPI2EIE

0000

IEC3 0826 — RTCIE DMA5IE DCIIE DCIEIE QEI1IE PSEMIE C2IE C2RXIE INT4IE INT3IE T9IE T8IE MI2C2IE SI2C2IE T7IE

0000

IEC4 0828 — — — —QEI2IE— PSESMIE — C2TXIE C1TXIE DMA7IE DMA6IE CRCIE U2EIE U1EIE —

0000

IEC5 082A PWM2IE PWM1IE IC9IE OC9IE SPI3IE SPI3EIE U4TXIE U4RXIE U4EIE USB1IE —— U3TXIE U3RXIE U3EIE —

0000

IEC6 082C — — — — — — — — — — — — — —PWM4IEPWM3IE

0000

IEC7 082E IC11IE OC11IE IC10IE OC10IE SPI4IE SPI4EIE DMA11IE DMA10IE DMA9IE DMA8IE — — — — — —

0000

IEC8 0830 — ICDIE IC16IE OC16IE IC15IE OC15IE IC14IE OC14IE IC13IE OC13IE — DMA14IE DMA13IE DMA12IE IC12IE OC12IE

0000

IPC0 0840 — T1IP<2:0> —OC1IP<2:0> —IC1IP<2:0>— INT0IP<2:0>

4444

IPC1 0842 — T2IP<2:0> —OC2IP<2:0> —IC2IP<2:0>— DMA0IP<2:0>

4444

IPC2 0844 — U1RXIP<2:0> — SPI1IP<2:0> — SPI1EIP<2:0> — T3IP<2:0>

4444

IPC3 0846 — NVMIP<2:0> — DMA1IP<2:0> —AD1IP<2:0>— U1TXIP<2:0>

4444

IPC4 0848 —CNIP<2:0> — CMIP<2:0> — MI2C1IP<2:0> — SI2C1IP<2:0>

4444

IPC5 084A — IC8IP<2:0> —IC7IP<2:0> —AD2IP<2:0>— INT1IP<2:0>

4444

IPC6 084C — T4IP<2:0> —OC4IP<2:0> —OC3IP<2:0>— DMA2IP<2:0>

4444

IPC7 084E — U2TXIP<2:0> —U2RXIP<2:0> — INT2IP<2:0> — T5IP<2:0>

4444

IPC8 0850 — C1IP<2:0> —C1RXIP<2:0> — SPI2IP<2:0> —SPI2EIP<2:0>

4444

IPC9 0852 — IC5IP<2:0> —IC4IP<2:0> —IC3IP<2:0>— DMA3IP<2:0>

4444

IPC10 0854 —OC7IP<2:0> —OC6IP<2:0> —OC5IP<2:0>—IC6IP<2:0>

4444

IPC11 0856 — T6IP<2:0> — DMA4IP<2:0> —PMPIP<2:0>— OC8IP<2:0>

4444

IPC12 0858 — T8IP<2:0> — MI2C2IP<2:0> — SI2C2IP<2:0> — T7IP<2:0>

4444

IPC13 085A C2RXIP<2:0> — INT4IP<2:0> — INT3IP<2:0> — T9IP<2:0>

4444

IPC14 085C — DCIEIP<2:0> — QEI1IP<2:0> — PSEMIP<2:0> — C2IP<2:0>

4444

IPC15 085E — — — — —RTCIP<2:0> — DMA5IP<2:0> — DCIIP<2:0>

0444

Legend:

— = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 63

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

IPC16 0860 —CRCIP<2:0> —U2EIP<2:0> —U1EIP<2:0>— — — —

4440

IPC17 0862 — C2TXIP<2:0> — C1TXIP<2:0> — DMA7IP<2:0> — DMA6IP<2:0>

4444

IPC18 0864 — QEI2IP<2:0> — — — — — PSESMIP<2:0> — — — —

4040

IPC20 0868 — U3TXIP<2:0> —U3RXIP<2:0> —U3EIP<2:0>— — — —

4440

IPC21 086A —U4EIP<2:0> — USB1IP<2:0> — — — — — — — —

4400

IPC22 086C — SPI3IP<2:0> —SPI3EIP<2:0> — U4TXIP<2:0> — U4RXIP<2:0>

4444

IPC23 086E — PWM2IP<2:0> — PWM1IP<2:0> —IC9IP<2:0>— OC9IP<2:0>

4444

IPC24 0870 — — — — — — — — — PWM4IP<2:0> — PWM3IP<2:0>

0044

IPC29 087A — DMA9IP<2:0> — DMA8IP<2:0> — — — — — — — —

4400

IPC30 087C — SPI4IP<2:0> —SPI4EIP<2:0> —DMA11IP<2:0>— DMA10IP<2:0>

4444

IPC31 087E — IC11IP<2:0> — OC11IP<2:0> — IC10IP<2:0> — OC10IP<2:0>

4444

IPC32 0880 — DMA13IP<2:0> — DMA12IP<2:0> — IC12IP<2:0> — OC12IP<2:0>

4444

IPC33 0882 — IC13IP<2:0> — OC13IP<2:0> — — — — — DMA14IP<2:0>

4404

IPC34 0884 — IC15IP<2:0> — OC15IP<2:0> — IC14IP<2:0> — OC14IP<2:0>

4444

IPC35 0886 — — — — — ICDIP<2:0> — IC16IP<2:0> — OC16IP<2:0>

0444

INTCON1 08C0 NSTDIS OVAERR OVBERR COVAERR COVBERR OVATE OVBTE COVTE SFTACERR DIV0ERR DMACERR MATHERR ADDRERR STKERR OSCFAIL —

0000

INTCON2 08C2 GIE DISI SWTRAP — — — — — — — — INT4EP INT3EP INT2EP INT1EP INT0EP

8000

INTCON3 08C4 — — — — — — — — — UAE DAE DOOVR — — — —

0000

INTCON4 08C6 — — — — — — — — — — — — — — —SGHT

0000

INTTREG 08C8 — — — — — ILR<3:0> VECNUM<7:0>

0000

TABLE 4-5: INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33EPXXXMU806 DEVICES ONLY (CONTINUED)

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend:

— = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 64  2009-2012 Microchip Technology Inc.

TABLE 4-6: INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33EPXXXMC806 DEVICES ONLY

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

IFS0 0800 NVMIF DMA1IF AD1IF U1TXIF U1RXIF SPI1IF SPI1EIF T3IF T2IF OC2IF IC2IF DMA0IF T1IF OC1IF IC1IF INT0IF

0000

IFS1 0802 U2TXIF U2RXIF INT2IF T5IF T4IF OC4IF OC3IF DMA2IF IC8IF IC7IF AD2IF INT1IF CNIF CMIF MI2C1IF SI2C1IF

0000

IFS2 0804 T6IF DMA4IF PMPIF OC8IF OC7IF OC6IF OC5IF IC6IF IC5IF IC4IF IC3IF DMA3IF C1IF C1RXIF SPI2IF SPI2EIF

0000

IFS3 0806 — RTCIF DMA5IF DCIIF DCIEIF QEI1IF PSEMIF C2IF C2RXIF INT4IF INT3IF T9IF T8IF MI2C2IF SI2C2IF T7IF

0000

IFS4 0808 — — — —QEI2IF— PSESMIF — C2TXIF C1TXIF DMA7IF DMA6IF CRCIF U2EIF U1EIF —

0000

IFS5 080A PWM2IF PWM1IF IC9IF OC9IF SPI3IF SPI3EIF U4TXIF U4RXIF U4EIF — — — U3TXIF U3RXIF U3EIF —

0000

IFS6 080C — — — — — — — — — — — — — — PWM4IF PWM3IF

0000

IFS7 080E IC11IF OC11IF IC10IF OC10IF SPI4IF SPI4EIF DMA11IF DMA10IF DMA9IF DMA8IF — — — — — —

0000

IFS8 0810 — ICDIF IC16IF OC16IF IC15IF OC15IF IC14IF OC14IF IC13IF OC13IF — DMA14IF DMA13IF DMA12IF IC12IF OC12IF

0000

IEC0 0820 NVMIE DMA1IE AD1IE U1TXIE U1RXIE SPI1IE SPI1EIE T3IE T2IE OC2IE IC2IE DMA0IE T1IE OC1IE IC1IE INT0IE

0000

IEC1 0822 U2TXIE U2RXIE INT2IE T5IE T4IE OC4IE OC3IE DMA2IE IC8IE IC7IE AD2IE INT1IE CNIE CMIE MI2C1IE SI2C1IE

0000

IEC2 0824 T6IE DMA4IE PMPIE OC8IE OC7IE OC6IE OC5IE IC6IE IC5IE IC4IE IC3IE DMA3IE C1IE C1RXIE SPI2IE SPI2EIE

0000

IEC3 0826 — RTCIE DMA5IE DCIIE DCIEIE QEI1IE PSEMIE C2IE C2RXIE INT4IE INT3IE T9IE T8IE MI2C2IE SI2C2IE T7IE

0000

IEC4 0828 — — — —QEI2IE— PSESMIE — C2TXIE C1TXIE DMA7IE DMA6IE CRCIE U2EIE U1EIE —

0000

IEC5 082A PWM2IE PWM1IE IC9IE OC9IE SPI3IE SPI3EIE U4TXIE U4RXIE U4EIE — — — U3TXIE U3RXIE U3EIE —

0000

IEC6 082C — — — — — — — — — — — — — —PWM4IEPWM3IE

0000

IEC7 082E IC11IE OC11IE IC10IE OC10IE SPI4IE SPI4EIE DMA11IE DMA10IE DMA9IE DMA8IE — — — — — —

0000

IEC8 0830 — ICDIE IC16IE OC16IE IC15IE OC15IE IC14IE OC14IE IC13IE OC13IE — DMA14IE DMA13IE DMA12IE IC12IE OC12IE

0000

IPC0 0840 — T1IP<2:0> —OC1IP<2:0> —IC1IP<2:0>— INT0IP<2:0>

4444

IPC1 0842 — T2IP<2:0> —OC2IP<2:0> —IC2IP<2:0>— DMA0IP<2:0>

4444

IPC2 0844 — U1RXIP<2:0> — SPI1IP<2:0> — SPI1EIP<2:0> — T3IP<2:0>

4444

IPC3 0846 — NVMIP<2:0> — DMA1IP<2:0> —AD1IP<2:0>— U1TXIP<2:0>

4444

IPC4 0848 —CNIP<2:0> — CMIP<2:0> — MI2C1IP<2:0> — SI2C1IP<2:0>

4444

IPC5 084A — IC8IP<2:0> —IC7IP<2:0> —AD2IP<2:0>— INT1IP<2:0>

4444

IPC6 084C — T4IP<2:0> —OC4IP<2:0> —OC3IP<2:0>— DMA2IP<2:0>

4444

IPC7 084E — U2TXIP<2:0> —U2RXIP<2:0> — INT2IP<2:0> — T5IP<2:0>

4444

IPC8 0850 — C1IP<2:0> —C1RXIP<2:0> — SPI2IP<2:0> —SPI2EIP<2:0>

4444

IPC9 0852 — IC5IP<2:0> —IC4IP<2:0> —IC3IP<2:0>— DMA3IP<2:0>

4444

IPC10 0854 —OC7IP<2:0> —OC6IP<2:0> —OC5IP<2:0>—IC6IP<2:0>

4444

IPC11 0856 — T6IP<2:0> — DMA4IP<2:0> —PMPIP<2:0>— OC8IP<2:0>

4444

IPC12 0858 — T8IP<2:0> — MI2C2IP<2:0> — SI2C2IP<2:0> — T7IP<2:0>

4444

IPC13 085A C2RXIP<2:0> — INT4IP<2:0> — INT3IP<2:0> — T9IP<2:0>

4444

IPC14 085C — DCIEIP<2:0> — QEI1IP<2:0> — PSEMIP<2:0> — C2IP<2:0>

4444

IPC15 085E — — — — —RTCIP<2:0> — DMA5IP<2:0> — DCIIP<2:0>

0444

Legend:

— = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 65

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

IPC16 0860 —CRCIP<2:0> —U2EIP<2:0> —U1EIP<2:0>— — — —

4440

IPC17 0862 — C2TXIP<2:0> — C1TXIP<2:0> — DMA7IP<2:0> — DMA6IP<2:0>

4444

IPC18 0864 — QEI2IP<2:0> — — — — — PSESMIP<2:0> — — — —

4040

IPC20 0868 — U3TXIP<2:0> —U3RXIP<2:0> —U3EIP<2:0>— — — —

4440

IPC21 086A —U4EIP<2:0> — — — — — — — — — — — —

4400

IPC22 086C — SPI3IP<2:0> —SPI3EIP<2:0> — U4TXIP<2:0> — U4RXIP<2:0>

4444

IPC23 086E — PWM2IP<2:0> — PWM1IP<2:0> —IC9IP<2:0>— OC9IP<2:0>

4444

IPC24 0870 — — — — — — — — — PWM4IP<2:0> — PWM3IP<2:0>

0044

IPC29 087A — DMA9IP<2:0> — DMA8IP<2:0> — — — — — — — —

4400

IPC30 087C — SPI4IP<2:0> —SPI4EIP<2:0> —DMA11IP<2:0>— DMA10IP<2:0>

4444

IPC31 087E — IC11IP<2:0> — OC11IP<2:0> — IC10IP<2:0> — OC10IP<2:0>

4444

IPC32 0880 — DMA13IP<2:0> — DMA12IP<2:0> — IC12IP<2:0> — OC12IP<2:0>

4444

IPC33 0882 — IC13IP<2:0> — OC13IP<2:0> — — — — — DMA14IP<2:0>

4404

IPC34 0884 — IC15IP<2:0> — OC15IP<2:0> — IC14IP<2:0> — OC14IP<2:0>

4444

IPC35 0886 — — — — — ICDIP<2:0> — IC16IP<2:0> — OC16IP<2:0>

0444

INTCON1 08C0 NSTDIS OVAERR OVBERR COVAERR COVBERR OVATE OVBTE COVTE SFTACERR DIV0ERR DMACERR MATHERR ADDRERR STKERR OSCFAIL —

0000

INTCON2 08C2 GIE DISI SWTRAP — — — — — — — — INT4EP INT3EP INT2EP INT1EP INT0EP

8000

INTCON3 08C4 — — — — — — — — — UAE DAE DOOVR — — — —

0000

INTCON4 08C6 — — — — — — — — — — — — — — —SGHT

0000

INTTREG 08C8 — — — — — ILR<3:0> VECNUM<7:0>

0000

TABLE 4-6: INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33EPXXXMC806 DEVICES ONLY (CONTINUED)

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend:

— = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 66  2009-2012 Microchip Technology Inc.

TABLE 4-7: INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33EPXXXGP806 AND PIC24EPXXXGP806 DEVICES ONLY

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

IFS0 0800 NVMIF DMA1IF AD1IF U1TXIF U1RXIF SPI1IF SPI1EIF T3IF T2IF OC2IF IC2IF DMA0IF T1IF OC1IF IC1IF INT0IF 0000

IFS1 0802 U2TXIF U2RXIF INT2IF T5IF T4IF OC4IF OC3IF DMA2IF IC8IF IC7IF AD2IF INT1IF CNIF CMIF MI2C1IF SI2C1IF 0000

IFS2 0804 T6IF DMA4IF PMPIF OC8IF OC7IF OC6IF OC5IF IC6IF IC5IF IC4IF IC3IF DMA3IF C1IF C1RXIF SPI2IF SPI2EIF 0000

IFS3 0806 — RTCIF DMA5IF DCIIF DCIEIF — PSEMIF C2IF C2RXIF INT4IF INT3IF T9IF T8IF MI2C2IF SI2C2IF T7IF 0000

IFS4 0808 — — — — — — PSESMIF — C2TXIF C1TXIF DMA7IF DMA6IF CRCIF U2EIF U1EIF —0000

IFS5 080A — — IC9IF OC9IF SPI3IF SPI3EIF U4TXIF U4RXIF U4EIF — — — U3TXIF U3RXIF U3EIF —0000

IFS6 080C — — — — — — — — — — — — — — — — 0000

IFS7 080E IC11IF OC11IF IC10IF OC10IF SPI4IF SPI4EIF DMA11IF DMA10IF DMA9IF DMA8IF — — — — — — 0000

IFS8 0810 — ICDIF IC16IF OC16IF IC15IF OC15IF IC14IF OC14IF IC13IF OC13IF — DMA14IF DMA13IF DMA12IF IC12IF OC12IF 0000

IEC0 0820 NVMIE DMA1IE AD1IE U1TXIE U1RXIE SPI1IE SPI1EIE T3IE T2IE OC2IE IC2IE DMA0IE T1IE OC1IE IC1IE INT0IE 0000

IEC1 0822 U2TXIE U2RXIE INT2IE T5IE T4IE OC4IE OC3IE DMA2IE IC8IE IC7IE AD2IE INT1IE CNIE CMIE MI2C1IE SI2C1IE 0000

IEC2 0824 T6IE DMA4IE PMPIE OC8IE OC7IE OC6IE OC5IE IC6IE IC5IE IC4IE IC3IE DMA3IE C1IE C1RXIE SPI2IE SPI2EIE 0000

IEC3 0826 — RTCIE DMA5IE DCIIE DCIEIE — PSEMIE C2IE C2RXIE INT4IE INT3IE T9IE T8IE MI2C2IE SI2C2IE T7IE 0000

IEC4 0828 — — — — — — PSESMIE — C2TXIE C1TXIE DMA7IE DMA6IE CRCIE U2EIE U1EIE —0000

IEC5 082A —— IC9IE OC9IE SPI3IE SPI3EIE U4TXIE U4RXIE U4EIE — — — U3TXIE U3RXIE U3EIE —0000

IEC6 082C — — — — — — — — — — — — — — — — 0000

IEC7 082E IC11IE OC11IE IC10IE OC10IE SPI4IE SPI4EIE DMA11IE DMA10IE DMA9IE DMA8IE — — — — — — 0000

IEC8 0830 — ICDIE IC16IE OC16IE IC15IE OC15IE IC14IE OC14IE IC13IE OC13IE — DMA14IE DMA13IE DMA12IE IC12IE OC12IE 0000

IPC0 0840 — T1IP<2:0> — OC1IP<2:0> — IC1IP<2:0> — INT0IP<2:0> 4444

IPC1 0842 — T2IP<2:0> — OC2IP<2:0> — IC2IP<2:0> — DMA0IP<2:0> 4444

IPC2 0844 — U1RXIP<2:0> — SPI1IP<2:0> — SPI1EIP<2:0> — T3IP<2:0> 4444

IPC3 0846 —NVMIP<2:0> — DMA1IP<2:0> —AD1IP<2:0>— U1TXIP<2:0> 4444

IPC4 0848 — CNIP<2:0> — CMIP<2:0> — MI2C1IP<2:0> — SI2C1IP<2:0> 4444

IPC5 084A — IC8IP<2:0> — IC7IP<2:0> —AD2IP<2:0>— INT1IP<2:0> 4444

IPC6 084C — T4IP<2:0> — OC4IP<2:0> — OC3IP<2:0> — DMA2IP<2:0> 4444

IPC7 084E — U2TXIP<2:0> — U2RXIP<2:0> — INT2IP<2:0> — T5IP<2:0> 4444

IPC8 0850 — C1IP<2:0> — C1RXIP<2:0> — SPI2IP<2:0> — SPI2EIP<2:0> 4444

IPC9 0852 — IC5IP<2:0> — IC4IP<2:0> — IC3IP<2:0> — DMA3IP<2:0> 4444

IPC10 0854 —OC7IP<2:0> — OC6IP<2:0> — OC5IP<2:0> — IC6IP<2:0> 4444

IPC11 0856 — T6IP<2:0> — DMA4IP<2:0> —PMPIP<2:0>—OC8IP<2:0>4444

IPC12 0858 — T8IP<2:0> — MI2C2IP<2:0> — SI2C2IP<2:0> — T7IP<2:0> 4444

IPC13 085A C2RXIP<2:0> — INT4IP<2:0> — INT3IP<2:0> — T9IP<2:0> 4444

IPC14 085C — DCIEIP<2:0> — — — — — PSEMIP<2:0> — C2IP<2:0> 4444

IPC15 085E — — — — — RTCIP<2:0> — DMA5IP<2:0> — DCIIP<2:0> 0444

Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 67

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

IPC16 0860 — CRCIP<2:0> —U2EIP<2:0>—U1EIP<2:0>— — — — 4440

IPC17 0862 — C2TXIP<2:0> — C1TXIP<2:0> — DMA7IP<2:0> — DMA6IP<2:0> 4444

IPC18 0864 — — — — — — — — — PSESMIP<2:0> — — — — 4040

IPC20 0868 — U3TXIP<2:0> — U3RXIP<2:0> —U3EIP<2:0>— — — — 4440

IPC21 086A — U4EIP<2:0> — — — — — — — — — — — — 4400

IPC22 086C — SPI3IP<2:0> — SPI3EIP<2:0> — U4TXIP<2:0> — U4RXIP<2:0> 4444

IPC23 086E — — — — — — — — — IC9IP<2:0> —OC9IP<2:0>4444

IPC24 0870 — — — — — — — — — — — — — — — — 0044

IPC29 087A — DMA9IP<2:0> — DMA8IP<2:0> — — — — — — — — 4400

IPC30 087C — SPI4IP<2:0> — SPI4EIP<2:0> —DMA11IP<2:0>— DMA10IP<2:0> 4444

IPC31 087E — IC11IP<2:0> — OC11IP<2:0> — IC10IP<2:0> — OC10IP<2:0> 4444

IPC32 0880 — DMA13IP<2:0> — DMA12IP<2:0> — IC12IP<2:0> — OC12IP<2:0> 4444

IPC33 0882 — IC13IP<2:0> — OC13IP<2:0> — — — — — DMA14IP<2:0> 4404

IPC34 0884 — IC15IP<2:0> — OC15IP<2:0> — IC14IP<2:0> — OC14IP<2:0> 4444

IPC35 0886 — — — — —ICDIP<2:0>— IC16IP<2:0> — OC16IP<2:0> 0444

INTCON1 08C0 NSTDIS OVAERR OVBERR COVAERR COVBERR OVATE OVBTE COVTE SFTACERR DIV0ERR DMACERR MATHERR ADDRERR STKERR OSCFAIL —0000

INTCON2 08C2 GIE DISI SWTRAP — — — — — — — — INT4EP INT3EP INT2EP INT1EP INT0EP 8000

INTCON3 08C4 — — — — — — — — —UAEDAEDOOVR— — — — 0000

INTCON4 08C6 — — — — — — — — — — — — — — —SGHT0000

INTTREG 08C8 — — — — — ILR<3:0> VECNUM<7:0> 0000

TABLE 4-7: INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33EPXXXGP806 AND PIC24EPXXXGP806 DEVICES ONLY (CONTINUED)

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 68  2009-2012 Microchip Technology Inc.

TABLE 4-8: INTERRUPT CONTROLLER REGISTER MAP FOR PIC24EPXXXGU810/814 DEVICES ONLY

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

IFS0 0800 NVMIF DMA1IF AD1IF U1TXIF U1RXIF SPI1IF SPI1EIF T3IF T2IF OC2IF IC2IF DMA0IF T1IF OC1IF IC1IF INT0IF

0000

IFS1 0802 U2TXIF U2RXIF INT2IF T5IF T4IF OC4IF OC3IF DMA2IF IC8IF IC7IF AD2IF INT1IF CNIF CMIF MI2C1IF SI2C1IF

0000

IFS2 0804 T6IF DMA4IF PMPIF OC8IF OC7IF OC6IF OC5IF IC6IF IC5IF IC4IF IC3IF DMA3IF C1IF C1RXIF SPI2IF SPI2EIF

0000

IFS3 0806 — RTCIF DMA5IF DCIIF DCIEIF —— C2IF C2RXIF INT4IF INT3IF T9IF T8IF MI2C2IF SI2C2IF T7IF

0000

IFS4 0808 — — — — — — — — C2TXIF C1TXIF DMA7IF DMA6IF CRCIF U2EIF U1EIF —

0000

IFS5 080A —— IC9IF OC9IF SPI3IF SPI3EIF U4TXIF U4RXIF U4EIF USB1IF —— U3TXIF U3RXIF U3EIF —

0000

IFS7 080E IC11IF OC11IF IC10IF OC10IF SPI4IF SPI4EIF DMA11IF DMA10IF DMA9IF DMA8IF — — — — — —

0000

IFS8 0810 — ICDIF IC16IF OC16IF IC15IF OC15IF IC14IF OC14IF IC13IF OC13IF — DMA14IF DMA13IF DMA12IF IC12IF OC12IF

0000

IEC0 0820 NVMIE DMA1IE AD1IE U1TXIE U1RXIE SPI1IE SPI1EIE T3IE T2IE OC2IE IC2IE DMA0IE T1IE OC1IE IC1IE INT0IE

0000

IEC1 0822 U2TXIE U2RXIE INT2IE T5IE T4IE OC4IE OC3IE DMA2IE IC8IE IC7IE AD2IE INT1IE CNIE CMIE MI2C1IE SI2C1IE

0000

IEC2 0824 T6IE DMA4IE PMPIE OC8IE OC7IE OC6IE OC5IE IC6IE IC5IE IC4IE IC3IE DMA3IE C1IE C1RXIE SPI2IE SPI2EIE

0000

IEC3 0826 — RTCIE DMA5IE DCIIE DCIEIE —— C2IE C2RXIE INT4IE INT3IE T9IE T8IE MI2C2IE SI2C2IE T7IE

0000

IEC4 0828 — — — — — — — — C2TXIE C1TXIE DMA7IE DMA6IE CRCIE U2EIE U1EIE —

0000

IEC5 082A —— IC9IE OC9IE SPI3IE SPI3EIE U4TXIE U4RXIE U4EIE USB1IE —— U3TXIE U3RXIE U3EIE —

0000

IEC7 082E IC11IE OC11IE IC10IE OC10IE SPI4IE SPI4EIE DMA11IE DMA10IE DMA9IE DMA8IE — — — — — —

0000

IEC8 0830 — ICDIE IC16IE OC16IE IC15IE OC15IE IC14IE OC14IE IC13IE OC13IE — DMA14IE DMA13IE DMA12IE IC12IE OC12IE

0000

IPC0 0840 — T1IP<2:0> — OC1IP<2:0> — IC1IP<2:0> — INT0IP<2:0>

4444

IPC1 0842 — T2IP<2:0> — OC2IP<2:0> — IC2IP<2:0> — DMA0IP<2:0>

4444

IPC2 0844 — U1RXIP<2:0> — SPI1IP<2:0> — SPI1EIP<2:0> — T3IP<2:0>

4444

IPC3 0846 — NVMIP<2:0> — DMA1IP<2:0> —AD1IP<2:0>— U1TXIP<2:0>

4444

IPC4 0848 —CNIP<2:0> —CMIP<2:0> — MI2C1IP<2:0> — SI2C1IP<2:0>

4444

IPC5 084A — IC8IP<2:0> — IC7IP<2:0> —AD2IP<2:0>— INT1IP<2:0>

4444

IPC6 084C — T4IP<2:0> — OC4IP<2:0> — OC3IP<2:0> — DMA2IP<2:0>

4444

IPC7 084E — U2TXIP<2:0> — U2RXIP<2:0> — INT2IP<2:0> — T5IP<2:0>

4444

IPC8 0850 — C1IP<2:0> — C1RXIP<2:0> — SPI2IP<2:0> — SPI2EIP<2:0>

4444

IPC9 0852 — IC5IP<2:0> — IC4IP<2:0> — IC3IP<2:0> — DMA3IP<2:0>

4444

IPC10 0854 —OC7IP<2:0> — OC6IP<2:0> — OC5IP<2:0> — IC6IP<2:0>

4444

IPC11 0856 — T6IP<2:0> — DMA4IP<2:0> — PMPIP<2:0> — OC8IP<2:0>

4444

IPC12 0858 — T8IP<2:0> — MI2C2IP<2:0> — SI2C2IP<2:0> — T7IP<2:0>

4444

IPC13 085A C2RXIP<2:0> — INT4IP<2:0> — INT3IP<2:0> — T9IP<2:0>

4444

IPC14 085C — DCIEIP<2:0> — — — — — — — — — C2IP<2:0>

4004

IPC15 085E — — — — — RTCIP<2:0> — DMA5IP<2:0> —DCIIP<2:0>

0444

IPC16 0860 — CRCIP<2:0> —U2EIP<2:0> —U1EIP<2:0>— — — —

4440

IPC17 0862 — C2TXIP<2:0> — C1TXIP<2:0> — DMA7IP<2:0> — DMA6IP<2:0>

4444

Legend:

— = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 69

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

IPC20 0868 — U3TXIP<2:0> — U3RXIP<2:0> —U3EIP<2:0>— — — —

4440

IPC21 086A — U4EIP<2:0> — USB1IP<2:0> — — — — — — — —

4400

IPC22 086C — SPI3IP<2:0> — SPI3EIP<2:0> — U4TXIP<2:0> — U4RXIP<2:0>

4444

IPC23 086E — — — — — — — — — IC9IP<2:0> — OC9IP<2:0>

0044

IPC29 087A — DMA9IP<2:0> — DMA8IP<2:0> — — — — — — — —

4400

IPC30 087C — SPI4IP<2:0> — SPI4EIP<2:0> —DMA11IP<2:0>— DMA10IP<2:0>

4444

IPC31 087E — IC11IP<2:0> — OC11IP<2:0> — IC10IP<2:0> — OC10IP<2:0>

4444

IPC32 0880 — DMA13IP<2:0> — DMA12IP<2:0> — IC12IP<2:0> — OC12IP<2:0>

4444

IPC33 0882 — IC13IP<2:0> — OC13IP<2:0> — — — — — DMA14IP<2:0>

4404

IPC34 0884 — IC15IP<2:0> — OC15IP<2:0> — IC14IP<2:0> — OC14IP<2:0>

4444

IPC35 0886 — — — — — ICDIP<2:0> — IC16IP<2:0> — OC16IP<2:0>

4444

INTCON1

08C0 NSTDIS — — — — — — — —

DIV0ERR DMACERR MATHERR ADDRERR STKERR OSCFAIL

—

0000

INTCON2

08C2 GIE DISI

SWTRAP

— — — — — — — — INT4EP INT3EP INT2EP INT1EP INT0EP

8000

INTCON3

08C4 — — — — — — — — — UAE DAE DOOVR — — — —

0000

INTCON4

08C6 — — — — — — — — — — — — — — —SGHT

0000

INTTREG

08C8 — — — — — ILR<3:0> VECNUM<7:0>

0000

TABLE 4-8: INTERRUPT CONTROLLER REGISTER MAP FOR PIC24EPXXXGU810/814 DEVICES ONLY (CONTINUED)

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend:

— = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 70  2009-2012 Microchip Technology Inc.

TABLE 4-9: TIMER1 THROUGH TIMER9 REGISTER MAP

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TMR1 0100 Timer1 Register xxxx

PR1 0102 Period Register 1 FFFF

T1CON 0104 TON —TSIDL—————— TGATE TCKPS<1:0> —TSYNCTCS —0000

TMR2 0106 Timer2 Register xxxx

TMR3HLD 0108 Timer3 Holding Register (for 32-bit timer operations only) xxxx

TMR3 010A Timer3 Register xxxx

PR2 010C Period Register 2 FFFF

PR3 010E Period Register 3 FFFF

T2CON 0110 TON —TSIDL—————— TGATE TCKPS<1:0> T32 —TCS—0000

T3CON 0112 TON —TSIDL—————— TGATE TCKPS<1:0> ——TCS—0000

TMR4 0114 Timer4 Register xxxx

TMR5HLD 0116 Timer5 Holding Register (for 32-bit operations only) xxxx

TMR5 0118 Timer5 Register xxxx

PR4 011A Period Register 4 FFFF

PR5 011C Period Register 5 FFFF

T4CON 011E TON —TSIDL—————— TGATE TCKPS<1:0> T32 —TCS—0000

T5CON 0120 TON —TSIDL—————— TGATE TCKPS<1:0> ——TCS—0000

TMR6 0122 Timer6 Register xxxx

TMR7HLD 0124 Timer7 Holding Register (for 32-bit operations only) xxxx

TMR7 0126 Timer7 Register xxxx

PR6 0128 Period Register 6 FFFF

PR7 012A Period Register 7 FFFF

T6CON 012C TON —TSIDL—————— TGATE TCKPS<1:0> T32 —TCS—0000

T7CON 012E TON —TSIDL—————— TGATE TCKPS<1:0> ——TCS—0000

TMR8 0130 Timer8 Register xxxx

TMR9HLD 0132 Timer9 Holding Register (for 32-bit operations only) xxxx

TMR9 0134 Timer9 Register xxxx

PR8 0136 Period Register 8 FFFF

PR9 0138 Period Register 9 FFFF

T8CON 013A TON —TSIDL—————— TGATE TCKPS<1:0> T32 —TCS—0000

T9CON 013C TON —TSIDL—————— TGATE TCKPS<1:0> ——TCS—0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 71

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-10: INPUT CAPTURE 1 THROUGH INPUT CAPTURE 16 REGISTER MAP

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

IC1CON1 0140 —— ICSIDL ICTSEL<2:0> — — — ICI<1:0> ICOV ICBNE ICM<2:0> 0000

IC1CON2 0142 ——————— IC32 ICTRIG TRIGSTAT — SYNCSEL<4:0> 000D

IC1BUF 0144 Input Capture 1 Buffer Register xxxx

IC1TMR 0146 Input Capture 1 Timer 0000

IC2CON1 0148 —— ICSIDL ICTSEL<2:0> — — — ICI<1:0> ICOV ICBNE ICM<2:0> 0000

IC2CON2 014A ——————— IC32 ICTRIG TRIGSTAT — SYNCSEL<4:0> 000D

IC2BUF 014C Input Capture 2 Buffer Register xxxx

IC2TMR 014E Input Capture 2 Timer 0000

IC3CON1 0150 —— ICSIDL ICTSEL<2:0> — — — ICI<1:0> ICOV ICBNE ICM<2:0> 0000

IC3CON2 0152 ——————— IC32 ICTRIG TRIGSTAT — SYNCSEL<4:0> 000D

IC3BUF 0154 Input Capture 3 Buffer Register xxxx

IC3TMR 0156 Input Capture 3 Timer 0000

IC4CON1 0158 —— ICSIDL ICTSEL<2:0> — — — ICI<1:0> ICOV ICBNE ICM<2:0> 0000

IC4CON2 015A ——————— IC32 ICTRIG TRIGSTAT — SYNCSEL<4:0> 000D

IC4BUF 015C Input Capture 4 Buffer Register xxxx

IC4TMR 015E Input Capture 4 Timer 0000

IC5CON1 0160 —— ICSIDL ICTSEL<2:0> — — — ICI<1:0> ICOV ICBNE ICM<2:0> 0000

IC5CON2 0162 ——————— IC32 ICTRIG TRIGSTAT — SYNCSEL<4:0> 000D

IC5BUF 0164 Input Capture 5 Buffer Register xxxx

IC5TMR 0166 Input Capture 5 Timer 0000

IC6CON1 0168 —— ICSIDL ICTSEL<2:0> — — — ICI<1:0> ICOV ICBNE ICM<2:0> 0000

IC6CON2 016A ——————— IC32 ICTRIG TRIGSTAT — SYNCSEL<4:0> 000D

IC6BUF 016C Input Capture 6 Buffer Register xxxx

IC6TMR 016E Input Capture 6 Timer 0000

IC7CON1 0170 —— ICSIDL ICTSEL<2:0> — — — ICI<1:0> ICOV ICBNE ICM<2:0> 0000

IC7CON2 0172 ——————— IC32 ICTRIG TRIGSTAT — SYNCSEL<4:0> 000D

IC7BUF 0174 Input Capture 7 Buffer Register xxxx

IC7TMR 0176 Input Capture 7 Timer 0000

IC8CON1 0178 —— ICSIDL ICTSEL<2:0> — — — ICI<1:0> ICOV ICBNE ICM<2:0> 0000

IC8CON2 017A ——————— IC32 ICTRIG TRIGSTAT — SYNCSEL<4:0> 000D

IC8BUF 017C Input Capture 8 Buffer Register xxxx

IC8TMR 017E Input Capture 8 Timer 0000

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 72  2009-2012 Microchip Technology Inc.

IC9CON1 0180 —— ICSIDL ICTSEL<2:0> — — — ICI<1:0> ICOV ICBNE ICM<2:0> 0000

IC9CON2 0182 ——————— IC32 ICTRIG TRIGSTAT — SYNCSEL<4:0> 000D

IC9BUF 0184 Input Capture 9 Buffer Register xxxx

IC9TMR 0186 Input Capture 9 Timer 0000

IC10CON1 0188 —— ICSIDL ICTSEL<2:0> — — — ICI<1:0> ICOV ICBNE ICM<2:0> 0000

IC10CON2 018A ——————— IC32 ICTRIG TRIGSTAT — SYNCSEL<4:0> 000D

IC10BUF 018C Input Capture 10 Buffer Register xxxx

IC10TMR 018E Input Capture 10 Timer 0000

IC11CON1 0190 —— ICSIDL ICTSEL<2:0> — — — ICI<1:0> ICOV ICBNE ICM<2:0> 0000

IC11CON2 0192 ——————— IC32 ICTRIG TRIGSTAT — SYNCSEL<4:0> 000D

IC11BUF 0194 Input Capture 11 Buffer Register xxxx

IC11TMR 0196 Input Capture 11 Timer 0000

IC12CON1 0198 —— ICSIDL ICTSEL<2:0> — — — ICI<1:0> ICOV ICBNE ICM<2:0> 0000

IC12CON2 019A ——————— IC32 ICTRIG TRIGSTAT — SYNCSEL<4:0> 000D

IC12BUF 019C Input Capture 12 Buffer Register xxxx

IC12TMR 019E Input Capture 12 Timer 0000

IC13CON1 01A0 —— ICSIDL ICTSEL<2:0> — — — ICI<1:0> ICOV ICBNE ICM<2:0> 0000

IC13CON2 01A2 ——————— IC32 ICTRIG TRIGSTAT — SYNCSEL<4:0> 000D

IC13BUF 01A4 Input Capture 13 Buffer Register xxxx

IC13TMR 01A6 Input Capture 13 Timer 0000

IC14CON1 01A8 —— ICSIDL ICTSEL<2:0> — — — ICI<1:0> ICOV ICBNE ICM<2:0> 0000

IC14CON2 01AA ——————— IC32 ICTRIG TRIGSTAT — SYNCSEL<4:0> 000D

IC14BUF 01AC Input Capture 14 Buffer Register xxxx

IC14TMR 01AE Input Capture 14 Timer 0000

IC15CON1 01B0 —— ICSIDL ICTSEL<2:0> — — — ICI<1:0> ICOV ICBNE ICM<2:0> 0000

IC15CON2 01B2 ——————— IC32 ICTRIG TRIGSTAT — SYNCSEL<4:0> 000D

IC15BUF 01B4 Input Capture 15 Buffer Register xxxx

IC15TMR 01B6 Input Capture 15 Timer 0000

IC16CON1 01B8 —— ICSIDL ICTSEL<2:0> — — — ICI<1:0> ICOV ICBNE ICM<2:0> 0000

IC16CON2 01BA ——————— IC32 ICTRIG TRIGSTAT — SYNCSEL<4:0> 000D

IC16BUF 01BC Input Capture 16 Buffer Register xxxx

IC16TMR 01BE Input Capture 16 Timer 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

TABLE 4-10: INPUT CAPTURE 1 THROUGH INPUT CAPTURE 16 REGISTER MAP (CONTINUED)

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

 2009-2012 Microchip Technology Inc. DS70616G-page 73

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-11: OUTPUT COMPARE 1 THROUGH OUTPUT COMPARE 16 REGISTER MAP

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

OC1CON1 0900 —— OCSIDL OCTSEL<2:0> ENFLTC ENFLTB ENFLTA OCFLTC OCFLTB OCFLTA TRIGMODE OCM<2:0>

0000

OC1CON2 0902 FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL<4:0>

000C

OC1RS 0904 Output Compare 1 Secondary Register

xxxx

OC1R 0906 Output Compare 1 Register

xxxx

OC1TMR 0908 Timer Value 1 Register

xxxx

OC2CON1 090A —— OCSIDL OCTSEL<2:0> ENFLTC ENFLTB ENFLTA OCFLTC OCFLTB OCFLTA TRIGMODE OCM<2:0>

0000

OC2CON2 090C FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL<4:0>

000C

OC2RS 090E Output Compare 2 Secondary Register

xxxx

OC2R 0910 Output Compare 2 Register

xxxx

OC2TMR 0912 Timer Value 2 Register

xxxx

OC3CON1 0914 —— OCSIDL OCTSEL<2:0> ENFLTC ENFLTB ENFLTA OCFLTC OCFLTB OCFLTA TRIGMODE OCM<2:0>

0000

OC3CON2 0916 FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL<4:0>

000C

OC3RS 0918 Output Compare 3 Secondary Register

xxxx

OC3R 091A Output Compare 3 Register

xxxx

OC3TMR 091C Timer Value 3 Register

xxxx

OC4CON1 091E —— OCSIDL OCTSEL<2:0> ENFLTC ENFLTB ENFLTA OCFLTC OCFLTB OCFLTA TRIGMODE OCM<2:0>

0000

OC4CON2 0920 FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL<4:0>

000C

OC4RS 0922 Output Compare 4 Secondary Register

xxxx

OC4R 0924 Output Compare 4 Register

xxxx

OC4TMR 0926 Timer Value 4 Register

xxxx

OC5CON1 0928 —— OCSIDL OCTSEL<2:0> ENFLTC ENFLTB ENFLTA OCFLTC OCFLTB OCFLTA TRIGMODE OCM<2:0>

0000

OC5CON2 092A FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL<4:0>

000C

OC5RS 092C Output Compare 5 Secondary Register

xxxx

OC5R 092D Output Compare 5 Register

xxxx

OC5TMR 0930 Timer Value 5 Register

xxxx

OC6CON1 0932 —— OCSIDL OCTSEL<2:0> ENFLTC ENFLTB ENFLTA OCFLTC OCFLTB OCFLTA TRIGMODE OCM<2:0>

0000

OC6CON2 0934 FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL<4:0>

000C

OC6RS 0936 Output Compare 6 Secondary Register

xxxx

OC6R 0938 Output Compare 6 Register

xxxx

OC6TMR 093A Timer Value 6 Register

xxxx

OC7CON1 093C —— OCSIDL OCTSEL<2:0> ENFLTC ENFLTB ENFLTA OCFLTC OCFLTB OCFLTA TRIGMODE OCM<2:0>

0000

OC7CON2 093E FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL<4:0>

000C

OC7RS 0940 Output Compare 7 Secondary Register

xxxx

OC7R 0942 Output Compare 7 Register

xxxx

OC7TMR 0944 Timer Value 7 Register

xxxx

Legend:

— = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 74  2009-2012 Microchip Technology Inc.

OC8CON1 0946 —— OCSIDL OCTSEL<2:0> ENFLTC ENFLTB ENFLTA OCFLTC OCFLTB OCFLTA TRIGMODE OCM<2:0>

0000

OC8CON2 0948 FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL<4:0>

000C

OC8RS 094A Output Compare 8 Secondary Register

xxxx

OC8R 094C Output Compare 8 Register

xxxx

OC8TMR 094E Timer Value 8 Register

xxxx

OC9CON1 0950 —— OCSIDL OCTSEL<2:0> ENFLTC ENFLTB ENFLTA OCFLTC OCFLTB OCFLTA TRIGMODE OCM<2:0>

0000

OC9CON2 0952 FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL<4:0>

000C

OC9RS 0954 Output Compare 9 Secondary Register

xxxx

OC9R 0956 Output Compare 9 Register

xxxx

OC9TMR 0958 Timer Value 9 Register

xxxx

OC10CON1 095A —— OCSIDL OCTSEL<2:0> ENFLTC ENFLTB ENFLTA OCFLTC OCFLTB OCFLTA TRIGMODE OCM<2:0>

0000

OC10CON2 095C FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL<4:0>

000C

OC10RS 095E Output Compare 10 Secondary Register

xxxx

OC10R 0960 Output Compare 10 Register

xxxx

OC10TMR 0962 Timer Value 10 Register

xxxx

OC11CON1 0964 —— OCSIDL OCTSEL<2:0> ENFLTC ENFLTB ENFLTA OCFLTC OCFLTB OCFLTA TRIGMODE OCM<2:0>

0000

OC11CON2 0966 FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL<4:0>

000C

OC11RS 0968 Output Compare 11 Secondary Register

xxxx

OC11R 096A Output Compare 11 Register

xxxx

OC11TMR 096C Timer Value 11 Register

xxxx

OC12CON1 096E —— OCSIDL OCTSEL<2:0> ENFLTC ENFLTB ENFLTA OCFLTC OCFLTB OCFLTA TRIGMODE OCM<2:0>

0000

OC12CON2 0970 FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL<4:0>

000C

OC12RS 0972 Output Compare 12 Secondary Register

xxxx

OC12R 0974 Output Compare 12 Register

xxxx

OC12TMR 0976 Timer Value 12 Register

xxxx

OC13CON1 0978 —— OCSIDL OCTSEL<2:0> ENFLTC ENFLTB ENFLTA OCFLTC OCFLTB OCFLTA TRIGMODE OCM<2:0>

0000

OC13CON2 097A FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL<4:0>

000C

OC13RS 097C Output Compare 13 Secondary Register

xxxx

OC13R 097E Output Compare 13 Register

xxxx

OC13TMR 0980 Timer Value 13 Register

xxxx

OC14CON1 0982 —— OCSIDL OCTSEL<2:0> ENFLTC ENFLTB ENFLTA OCFLTC OCFLTB OCFLTA TRIGMODE OCM<2:0>

0000

OC14CON2 0984 FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL<4:0>

000C

OC14RS 0986 Output Compare 14 Secondary Register

xxxx

OC14R 0988 Output Compare 14 Register

xxxx

OC14TMR 098A Timer Value 14 Register

xxxx

TABLE 4-11: OUTPUT COMPARE 1 THROUGH OUTPUT COMPARE 16 REGISTER MAP (CONTINUED)

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend:

— = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 75

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

OC15CON1 098C —— OCSIDL OCTSEL<2:0> ENFLTC ENFLTB ENFLTA OCFLTC OCFLTB OCFLTA TRIGMODE OCM<2:0>

0000

OC15CON2 098E FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL<4:0>

000C

OC15RS 0990 Output Compare 15 Secondary Register

xxxx

OC15R 0992 Output Compare 15 Register

xxxx

OC15TMR 0994 Timer Value 15 Register

xxxx

OC16CON1 0996 —— OCSIDL OCTSEL<2:0> ENFLTC ENFLTB ENFLTA OCFLTC OCFLTB OCFLTA TRIGMODE OCM<2:0>

0000

OC16CON2 0998 FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL<4:0>

000C

OC16RS 099A Output Compare 16 Secondary Register

xxxx

OC16R 099C Output Compare 16 Register

xxxx

OC16TMR 099E Timer Value 16 Register

xxxx

TABLE 4-11: OUTPUT COMPARE 1 THROUGH OUTPUT COMPARE 16 REGISTER MAP (CONTINUED)

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend:

— = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 76  2009-2012 Microchip Technology Inc.

TABLE 4-12: PWM REGISTER MAP FOR dsPIC33EPXXX(MC/MU)806/810/814 DEVICES ONLY

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

PTCON 0C00 PTEN — PTSIDL SESTAT SEIEN EIPU SYNCPOL SYNCOEN SYNCEN SYNCSRC<2:0> SEVTPS<3:0> 0000

PTCON2 0C02 — — — — — — — — — — — — — PCLKDIV<2:0> 0000

PTPER 0C04 PTPER<15:0> FFF8

SEVTCMP 0C06 SEVTCMP<15:0> 0000

MDC 0C0A MDC<15:0> 0000

STCON 0C0E — — — SESTAT SEIEN EIPU SYNCPOL SYNCOEN SYNCEN SYNCSRC<2:0> SEVTPS<3:0> 0000

STCON2 0C10 — — — — — — — — — — — — — PCLKDIV<2:0> 0000

STPER 0C12 STPER<15:0> FFF8

SSEVTCMP 0C14 SSEVTCMP<15:0> 0000

CHOP 0C1A CHPCLKEN — — — — — CHOPCLK<9:0> 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

TABLE 4-13: PWM GENERATOR 1 REGISTER MAP FOR dsPIC33EPXXX(MC/MU)806/810/814 DEVICES ONLY

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

PWMCON1 0C20 FLTSTAT CLSTAT TRGSTAT FLTIEN CLIEN TRGIEN ITB MDCS DTC<1:0> DTCP — MTBS CAM XPRES IUE 0000

IOCON1 0C22 PENH PENL POLH POLL PMOD<1:0> OVRENH OVRENL OVRDAT<1:0> FLTDAT<1:0> CLDAT<1:0> SWAP OSYNC 0000

FCLCON1 0C24 IFLTMOD CLSRC<4:0> CLPOL CLMOD FLTSRC<4:0> FLTPOL FLTMOD<1:0> 0000

PDC1 0C26 PDC1<15:0> 0000

PHASE1 0C28 PHASE1<15:0> 0000

DTR1 0C2A — — DTR1<13:0> 0000

ALTDTR1 0C2C — — ALTDTR1<13:0> 0000

SDC1 0C2E SDC1<15:0> 0000

SPHASE1 0C30 SPHASE1<15:0> 0000

TRIG1 0C32 TRGCMP<15:0> 0000

TRGCON1 0C34 TRGDIV<3:0> — — — — — —TRGSTRT<5:0>0000

PWMCAP1 0C38 PWMCAP1<15:0> 0000

LEBCON1 0C3A PHR PHF PLR PLF FLTLEBEN CLLEBEN — — — — BCH BCL BPHH BPHL BPLH BPLL 0000

LEBDLY1 0C3C — — — — LEB<11:0> 0000

AUXCON1 0C3E — — — — BLANKSEL<3:0> —— CHOPSEL<3:0> CHOPHEN CHOPLEN 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 77

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-14: PWM GENERATOR 2 REGISTER MAP FOR dsPIC33EPXXX(MC/MU)806/810/814 DEVICES ONLY

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

PWMCON2 0C40 FLTSTAT CLSTAT TRGSTAT FLTIEN CLIEN TRGIEN ITB MDCS DTC<1:0> DTCP — MTBS CAM XPRES IUE 0000

IOCON2 0C42 PENH PENL POLH POLL PMOD<1:0> OVRENH OVRENL OVRDAT<1:0> FLTDAT<1:0> CLDAT<1:0> SWAP OSYNC 0000

FCLCON2 0C44 IFLTMOD CLSRC<4:0> CLPOL CLMOD FLTSRC<4:0> FLTPOL FLTMOD<1:0> 0000

PDC2 0C46 PDC2<15:0> 0000

PHASE2 0C48 PHASE2<15:0> 0000

DTR2 0C4A — — DTR2<13:0> 0000

ALTDTR2 0C4C — — ALTDTR2<13:0> 0000

SDC2 0C4E SDC2<15:0> 0000

SPHASE2 0C50 SPHASE2<15:0> 0000

TRIG2 0C52 TRGCMP<15:0> 0000

TRGCON2 0C54 TRGDIV<3:0> — — — — — —TRGSTRT<5:0>0000

PWMCAP2 0C58 PWMCAP2<15:0> 0000

LEBCON2 0C5A PHR PHF PLR PLF FLTLEBEN CLLEBEN — — — — BCH BCL BPHH BPHL BPLH BPLL 0000

LEBDLY2 0C5C — — — — LEB<11:0> 0000

AUXCON2 0C5E — — — — BLANKSEL<3:0> —— CHOPSEL<3:0> CHOPHEN CHOPLEN 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

TABLE 4-15: PWM GENERATOR 3 REGISTER MAP FOR dsPIC33EPXXX(MC/MU)806/810/814 DEVICES ONLY

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

PWMCON3 0C60 FLTSTAT CLSTAT TRGSTAT FLTIEN CLIEN TRGIEN ITB MDCS DTC<1:0> DTCP — MTBS CAM XPRES IUE 0000

IOCON3 0C62 PENH PENL POLH POLL PMOD<1:0> OVRENH OVRENL OVRDAT<1:0> FLTDAT<1:0> CLDAT<1:0> SWAP OSYNC 0000

FCLCON3 0C64 IFLTMOD CLSRC<4:0> CLPOL CLMOD FLTSRC<4:0> FLTPOL FLTMOD<1:0> 0000

PDC3 0C66 PDC3<15:0> 0000

PHASE3 0C68 PHASE3<15:0> 0000

DTR3 0C6A — — DTR3<13:0> 0000

ALTDTR3 0C6C — — ALTDTR3<13:0> 0000

SDC3 0C6E SDC3<15:0> 0000

SPHASE3 0C70 SPHASE3<15:0> 0000

TRIG3 0C72 TRGCMP<15:0> 0000

TRGCON3 0C74 TRGDIV<3:0> — — — — — —TRGSTRT<5:0>0000

PWMCAP3 0C78 PWMCAP3<15:0> 0000

LEBCON3 0C7A PHR PHF PLR PLF FLTLEBEN CLLEBEN — — — — BCH BCL BPHH BPHL BPLH BPLL 0000

LEBDLY3 0C7C — — — — LEB<11:0> 0000

AUXCON3 0C7E — — — — BLANKSEL<3:0> —— CHOPSEL<3:0> CHOPHEN CHOPLEN 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 78  2009-2012 Microchip Technology Inc.

TABLE 4-16: PWM GENERATOR 4 REGISTER MAP FOR dsPIC33EPXXX(MC/MU)806/810/814 DEVICES ONLY

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

PWMCON4 0C80 FLTSTAT CLSTAT TRGSTAT FLTIEN CLIEN TRGIEN ITB MDCS DTC<1:0> DTCP — MTBS CAM XPRES IUE 0000

IOCON4 0C82 PENH PENL POLH POLL PMOD<1:0> OVRENH OVRENL OVRDAT<1:0> FLTDAT<1:0> CLDAT<1:0> SWAP OSYNC 0000

FCLCON4 0C84 IFLTMOD CLSRC<4:0> CLPOL CLMOD FLTSRC<4:0> FLTPOL FLTMOD<1:0> 0000

PDC4 0C86 PDC4<15:0> 0000

PHASE4 0C88 PHASE4<15:0> 0000

DTR4 0C8A — — DTR4<13:0> 0000

ALTDTR4 0C8C — — ALTDTR4<13:0> 0000

SDC4 0C8E SDC4<15:0> 0000

SPHASE4 0C90 SPHASE4<15:0> 0000

TRIG4 0C92 TRGCMP<15:0> 0000

TRGCON4 0C94 TRGDIV<3:0> — — — — — —TRGSTRT<5:0>0000

PWMCAP4 0C98 PWMCAP4<15:0> 0000

LEBCON4 0C9A PHR PHF PLR PLF FLTLEBEN CLLEBEN ———— BCH BCL BPHH BPHL BPLH BPLL 0000

LEBDLY4 0C9C — — — — LEB<11:0> 0000

AUXCON4 0C9E — — — — BLANKSEL<3:0> —— CHOPSEL<3:0> CHOPHEN CHOPLEN 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

TABLE 4-17: PWM GENERATOR 5 REGISTER MAP FOR dsPIC33EPXXX(MC/MU)810/814 DEVICES ONLY

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

PWMCON5 0CA0 FLTSTAT CLSTAT TRGSTAT FLTIEN CLIEN TRGIEN ITB MDCS DTC<1:0> DTCP — MTBS CAM XPRES IUE 0000

IOCON5 0CA2 PENH PENL POLH POLL PMOD<1:0> OVRENH OVRENL OVRDAT<1:0> FLTDAT<1:0> CLDAT<1:0> SWAP OSYNC 0000

FCLCON5 0CA4 IFLTMOD CLSRC<4:0> CLPOL CLMOD FLTSRC<4:0> FLTPOL FLTMOD<1:0> 0000

PDC5 0CA6 PDC5<15:0> 0000

PHASE5 0CA8 PHASE5<15:0> 0000

DTR5 0CAA — — DTR5<13:0> 0000

ALTDTR5 0CAC — — ALTDTR5<13:0> 0000

SDC5 0CAE SDC5<15:0> 0000

SPHASE5 0CB0 SPHASE5<15:0> 0000

TRIG5 0CB2 TRGCMP<15:0> 0000

TRGCON5 0CB4 TRGDIV<3:0> — — — — — —TRGSTRT<5:0>0000

PWMCAP5 0CB8 PWM Capture<15:0> 0000

LEBCON5 0CBA PHR PHF PLR PLF FLTLEBEN CLLEBEN — — — — BCH BCL BPHH BPHL BPLH BPLL 0000

LEBDLY5 0CBC —— —— LEB<11:0> 0000

AUXCON5 0CBE —— —— BLANKSEL<3:0> —— CHOPSEL<3:0> CHOPHEN CHOPLEN 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 79

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-18: PWM GENERATOR 6 REGISTER MAP FOR dsPIC33EPXXX(MC/MU)810/814 DEVICES ONLY

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

PWMCON6 0CC0 FLTSTAT CLSTAT TRGSTAT FLTIEN CLIEN TRGIEN ITB MDCS DTC<1:0> DTCP — MTBS CAM XPRES IUE 0000

IOCON6 0CC2 PENH PENL POLH POLL PMOD<1:0> OVRENH OVRENL OVRDAT<1:0> FLTDAT<1:0> CLDAT<1:0> SWAP OSYNC 0000

FCLCON6 0CC4 IFLTMOD CLSRC<4:0> CLPOL CLMOD FLTSRC<4:0> FLTPOL FLTMOD<1:0> 0000

PDC6 0CC6 PDC6<15:0> 0000

PHASE6 0CC8 PHASE6<15:0> 0000

DTR6 0CCA — — DTR6<13:0> 0000

ALTDTR6 0CCC — — ALTDTR6<13:0> 0000

SDC6 0CCE SDC6<15:0> 0000

SPHASE6 0CD0 SPHASE6<15:0> 0000

TRIG6 0CD2 TRGCMP<15:0> 0000

TRGCON6 0CD4 TRGDIV<3:0> — — — — — —TRGSTRT<5:0>0000

PWMCAP6 0CD8 PWMCAP6<15:0> 0000

LEBCON6 0CDA PHR PHF PLR PLF FLTLEBEN CLLEBEN — — — — BCH BCL BPHH BPHL BPLH BPLL 0000

LEBDLY6 0CDC — — — — LEB<11:0> 0000

AUXCON6 0CDE — — — — BLANKSEL<3:0> —— CHOPSEL<3:0> CHOPHEN CHOPLEN 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

TABLE 4-19: PWM GENERATOR 7 REGISTER MAP FOR dsPIC33EPXXX(MC/MU)814 DEVICES ONLY

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

PWMCON7 0CE0 FLTSTAT CLSTAT TRGSTAT FLTIEN CLIEN TRGIEN ITB MDCS DTC<1:0> DTCP — MTBS CAM XPRES IUE 0000

IOCON7 0CE2 PENH PENL POLH POLL PMOD<1:0> OVRENH OVRENL OVRDAT<1:0> FLTDAT<1:0> CLDAT<1:0> SWAP OSYNC 0000

FCLCON7 0CE4 IFLTMOD CLSRC<4:0> CLPOL CLMOD FLTSRC<4:0> FLTPOL FLTMOD<1:0> 0000

PDC7 0CE6 PDC7<15:0> 0000

PHASE7 0CE8 PHASE7<15:0> 0000

DTR7 0CEA — — DTR7<13:0> 0000

ALTDTR7 0CEC — — ALTDTR7<13:0> 0000

SDC7 0CEE SDC7<15:0> 0000

SPHASE7 0CF0 SPHASE7<15:0> 0000

TRIG7 0CF2 TRGCMP<15:0> 0000

TRGCON7 0CF4 TRGDIV<3:0> — — — — — —TRGSTRT<5:0>0000

PWMCAP7 0CF8 PWMCAP7<15:0> 0000

LEBCON7 0CFA PHR PHF PLR PLF FLTLEBEN CLLEBEN — — — — BCH BCL BPHH BPHL BPLH BPLL 0000

LEBDLY7 0CFC — — — — LEB<11:0> 0000

AUXCON7 0CFE — — — — BLANKSEL<3:0> —— CHOPSEL<3:0> CHOPHEN CHOPLEN 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 80  2009-2012 Microchip Technology Inc.

TABLE 4-20: QEI1 REGISTER MAP FOR dsPIC33EPXXX(MC/MU)806/810/814 DEVICES ONLY

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

QEI1CON 01C0 QEIEN — QEISIDL PIMOD<2:0> IMV<1:0> — INTDIV<2:0> CNTPOL GATEN CCM<1:0>

0000

QEI1IOC 01C2 QCAPEN FLTREN QFDIV<2:0> OUTFNC<1:0> SWPAB HOMPOL IDXPOL QEBPOL QEAPOL HOME INDEX QEB QEA

000x

QEI1STAT 01C4 —— PCHEQIRQ PCHEQIEN PCLEQIRQ PCLEQIEN POSOVIRQ POSOVIEN PCIIRQ PCIIEN VELOVIRQ VELOVIEN HOMIRQ HOMIEN IDXIRQ IDXIEN

0000

POS1CNTL 01C6 POSCNT<15:0>

0000

POS1CNTH 01C8 POSCNT<31:16>

0000

POS1HLD 01CA POSHLD<15:0>

0000

VEL1CNT 01CC VELCNT<15:0>

0000

INT1TMRL 01CE INTTMR<15:0>

0000

INT1TMRH 01D0 INTTMR<31:16>

0000

INT1HLDL 01D2 INTHLD<15:0>

0000

INT1HLDH 01D4 INTHLD<31:16>

0000

INDX1CNTL 01D6 INDXCNT<15:0>

0000

INDX1CNTH 01D8 INDXCNT<31:16>

0000

INDX1HLD 01DA INDXHLD<15:0>

0000

QEI1GECL 01DC QEIGEC<15:0>

0000

QEI1ICL 01DC QEIIC<15:0>

0000

QEI1GECH 01DE QEIGEC<31:16>

0000

QEI1ICH 01DE QEIIC<31:16>

0000

QEI1LECL 01E0 QEILEC<15:0>

0000

QEI1LECH 01E2 QEILEC<31:16>

0000

Legend:

= unknown value on Reset, — = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 81

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-21: QEI2 REGISTER MAP FOR dsPIC33EPXXX(MC/MU)806/810/814 DEVICES ONLY

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

QEI2CON 05C0 QEIEN — QEISIDL PIMOD<2:0> IMV<1:0> — INTDIV<2:0> CNTPOL GATEN CCM<1:0>

0000

QEI2IOC 05C2 QCAPEN FLTREN QFDIV<2:0> OUTFNC<1:0> SWPAB HOMPOL IDXPOL QEBPOL QEAPOL HOME INDEX QEB QEA

000x

QEI2STAT 05C4 —— PCHEQIRQ PCHEQIEN PCLEQIRQ PCLEQIEN POSOVIRQ POSOVIEN PCIIRQ PCIIEN VELOVIRQ VELOVIEN HOMIRQ HOMIEN IDXIRQ IDXIEN

0000

POS2CNTL 05C6 POSCNT<15:0>

0000

POS2CNTH 05C8 POSCNT<31:16>

0000

POS2HLD 05CA POSHLD<15:0>

0000

VEL2CNT 05CC VELCNT<15:0>

0000

INT2TMRL 05CE INTTMR<15:0>

0000

INT2TMRH 05D0 INTTMR<31:16>

0000

INT2HLDL 05D2 INTHLD<15:0>

0000

INT2HLDH 05D4 INTHLD<31:16>

0000

INDX2CNTL 05D6 INDXCNT<15:0>

0000

INDX2CNTH 05D8 INDXCNT<31:16>

0000

INDX2HLD 05DA INDXHLD<15:0>

0000

QEI2GECL 05DC QEIGEC<15:0>

0000

QEI2ICL 05DC QEIIC<15:0>

0000

QEI2GECH 05DE QEIGEC<31:16>

0000

QEI2ICH 05DE QEIIC<31:16>

0000

QEI2LECL 05E0 QEILEC<15:0>

0000

QEI2LECH 05E2 QEILEC<31:16>

0000

Legend:

= unknown value on Reset, — = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 82  2009-2012 Microchip Technology Inc.

TABLE 4-22: I2C1 and I2C2 REGISTER MAP

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

I2C1RCV 0200 — — — — — — — — I2Cx Receive Register 0000

I2C1TRN 0202 — — — — — — — — I2Cx Transmit Register 00FF

I2C1BRG 0204 — — — — — — — Baud Rate Generator 0000

I2C1CON 0206 I2CEN — I2CSIDL SCLREL IPMIEN A10M DISSLW SMEN GCEN STREN ACKDT ACKEN RCEN PEN RSEN SEN 1000

I2C1STAT 0208 ACKSTAT TRSTAT — — — BCL GCSTAT ADD10 IWCOL I2COV D_A P S R_W RBF TBF 0000

I2C1ADD 020A — — — — — — I2Cx Address Register 0000

I2C1MSK 020C — — — — — — I2Cx Address Mask 0000

I2C2RCV 0210 — — — — — — — — I2Cx Receive Register 0000

I2C2TRN 0212 — — — — — — — — I2Cx Transmit Register 00FF

I2C2BRG 0214 — — — — — — — Baud Rate Generator 0000

I2C2CON 0216 I2CEN — I2CSIDL SCLREL IPMIEN A10M DISSLW SMEN GCEN STREN ACKDT ACKEN RCEN PEN RSEN SEN 1000

I2C2STAT 0218 ACKSTAT TRSTAT — — — BCL GCSTAT ADD10 IWCOL I2COV D_A P S R_W RBF TBF 0000

I2C2ADD 021A — — — — — — I2Cx Address Register 0000

I2C2MSK 021C — — — — — — I2Cx Address Mask 0000

Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 83

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-23: UART1, UART2, UART3 and UART4 REGISTER MAP

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

U1MODE 0220 UARTEN — USIDL IREN RTSMD — UEN<1:0> WAKE LPBACK ABAUD URXINV BRGH PDSEL<1:0> STSEL 0000

U1STA 0222 UTXISEL1 UTXINV UTXISEL0 — UTXBRK UTXEN UTXBF TRMT URXISEL<1:0> ADDEN RIDLE PERR FERR OERR URXDA 0110

U1TXREG 0224 — — — — — — — UARTx Transmit Register xxxx

U1RXREG 0226 — — — — — — — UARTxReceive Register 0000

U1BRG 0228 Baud Rate Generator Prescaler 0000

U2MODE 0230 UARTEN — USIDL IREN RTSMD — UEN<1:0> WAKE LPBACK ABAUD URXINV BRGH PDSEL<1:0> STSEL 0000

U2STA 0232 UTXISEL1 UTXINV UTXISEL0 — UTXBRK UTXEN UTXBF TRMT URXISEL<1:0> ADDEN RIDLE PERR FERR OERR URXDA 0110

U2TXREG 0234 — — — — — — — UARTx Transmit Register xxxx

U2RXREG 0236 — — — — — — — UARTx Receive Register 0000

U2BRG 0238 Baud Rate Generator Prescaler 0000

U3MODE 0250 UARTEN — USIDL IREN RTSMD — UEN<1:0> WAKE LPBACK ABAUD URXINV BRGH PDSEL<1:0> STSEL 0000

U3STA 0252 UTXISEL1 UTXINV UTXISEL0 — UTXBRK UTXEN UTXBF TRMT URXISEL<1:0> ADDEN RIDLE PERR FERR OERR URXDA 0110

U3TXREG 0254 — — — — — — — UARTx Transmit Register xxxx

U3RXREG 0256 — — — — — — — UARTx Receive Register 0000

U3BRG 0258 Baud Rate Generator Prescaler 0000

U4MODE 02B0 UARTEN — USIDL IREN RTSMD — UEN<1:0> WAKE LPBACK ABAUD URXINV BRGH PDSEL<1:0> STSEL 0000

U4STA 02B2 UTXISEL1 UTXINV UTXISEL0 — UTXBRK UTXEN UTXBF TRMT URXISEL<1:0> ADDEN RIDLE PERR FERR OERR URXDA 0110

U4TXREG 02B4 — — — — — — — UARTx Transmit Register xxxx

U4RXREG 02B6 — — — — — — — UARTx Receive Register 0000

U4BRG 02B8 Baud Rate Generator Prescaler 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 84  2009-2012 Microchip Technology Inc.

TABLE 4-24: SPI1, SPI2, SPI3 and SPI4 REGISTER MAP

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

SPI1STAT 0240 SPIEN —SPISIDL—— SPIBEC<2:0> SRMPT SPIROV SRXMPT SISEL<2:0> SPITBF SPIRBF 0000

SPI1CON1 0242 — — — DISSCK DISSDO MODE16 SMP CKE SSEN CKP MSTEN SPRE<2:0> PPRE<1:0> 0000

SPI1CON2 0244 FRMEN SPIFSD FRMPOL — — — — — — — — — — — FRMDLY SPIBEN 0000

SPI1BUF 0248 SPIx Transmit and Receive Buffer Register 0000

SPI2STAT 0260 SPIEN —SPISIDL—— SPIBEC<2:0> SRMPT SPIROV SRXMPT SISEL<2:0> SPITBF SPIRBF 0000

SPI2CON1 0262 — — — DISSCK DISSDO MODE16 SMP CKE SSEN CKP MSTEN SPRE<2:0> PPRE<1:0> 0000

SPI2CON2 0264 FRMEN SPIFSD FRMPOL — — — — — — — — — — — FRMDLY SPIBEN 0000

SPI2BUF 0268 SPIx Transmit and Receive Buffer Register 0000

SPI3STAT 02A0 SPIEN —SPISIDL—— SPIBEC<2:0> SRMPT SPIROV SRXMPT SISEL<2:0> SPITBF SPIRBF 0000

SPI3CON1 02A2 — — — DISSCK DISSDO MODE16 SMP CKE SSEN CKP MSTEN SPRE<2:0> PPRE<1:0> 0000

SPI3CON2 02A4 FRMEN SPIFSD FRMPOL — — — — — — — — — — — FRMDLY SPIBEN 0000

SPI3BUF 02A8 SPIx Transmit and Receive Buffer Register 0000

SPI4STAT 02C0 SPIEN —SPISIDL—— SPIBEC<2:0> SRMPT SPIROV SRXMPT SISEL<2:0> SPITBF SPIRBF 0000

SPI4CON1 02C2 — — — DISSCK DISSDO MODE16 SMP CKE SSEN CKP MSTEN SPRE<2:0> PPRE<1:0> 0000

SPI4CON2 02C4 FRMEN SPIFSD FRMPOL — — — — — — — — — — — FRMDLY SPIBEN 0000

SPI4BUF 02C8 SPIx Transmit and Receive Buffer Register 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 85

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-25: ADC1 and ADC2 REGISTER MAP

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

ADC1BUF0 0300 ADCx Data Buffer 0 xxxx

ADC1BUF1 0302 ADCx Data Buffer 1 xxxx

ADC1BUF2 0304 ADCx Data Buffer 2 xxxx

ADC1BUF3 0306 ADCx Data Buffer 3 xxxx

ADC1BUF4 0308 ADCx Data Buffer 4 xxxx

ADC1BUF5 030A ADCx Data Buffer 5 xxxx

ADC1BUF6 030C ADCx Data Buffer 6 xxxx

ADC1BUF7 030E ADCx Data Buffer 7 xxxx

ADC1BUF8 0310 ADCx Data Buffer 8 xxxx

ADC1BUF9 0312 ADCx Data Buffer 9 xxxx

ADC1BUFA 0314 ADCx Data Buffer 10 xxxx

ADC1BUFB 0316 ADCx Data Buffer 11 xxxx

ADC1BUFC 0318 ADCx Data Buffer 12 xxxx

ADC1BUFD 031A ADCx Data Buffer 13 xxxx

ADC1BUFE 031C ADCx Data Buffer 14 xxxx

ADC1BUFF 031E ADCx Data Buffer 15 xxxx

AD1CON1 0320 ADON — ADSIDL ADDMABM — AD12B FORM<1:0> SSRC<2:0> SSRCG SIMSAM ASAM SAMP DONE 0000

AD1CON2 0322 VCFG<2:0> —— CSCNA CHPS<1:0> BUFS SMPI<4:0> BUFM ALTS 0000

AD1CON3 0324 ADRC —— SAMC<4:0> ADCS<7:0> 0000

AD1CHS123 0326 — — — — — CH123NB<1:0> CH123SB — — — — — CH123NA<1:0> CH123SA 0000

AD1CHS0 0328 CH0NB —— CH0SB<4:0> CH0NA ——CH0SA<4:0>0000

AD1CSSH 032E CSS31 CSS30 CSS29 CSS28 CSS27 CSS26 CSS25 CSS24 CSS23(1)CSS22(1)CSS21(1)CSS20(1)CSS19(1)CSS18(1)CSS17(1)CSS16(1)0000

AD1CSSL 0330 CSS15 CSS14 CSS13 CSS12 CSS11 CSS10 CSS9 CSS8 CSS7 CSS6 CSS5 CSS4 CSS3 CSS2 CSS1 CSS0 0000

AD1CON4 0332 — — — — — — — ADDMAEN — — — — — DMABL<2:0> 0000

ADC2BUF0 0340 ADCx Data Buffer 0 xxxx

ADC2BUF1 0342 ADCx Data Buffer 1 xxxx

ADC2BUF2 0344 ADCx Data Buffer 2 xxxx

ADC2BUF3 0346 ADCx Data Buffer 3 xxxx

ADC2BUF4 0348 ADCx Data Buffer 4 xxxx

ADC2BUF5 034A ADCx Data Buffer 5 xxxx

ADC2BUF6 034C ADCx Data Buffer 6 xxxx

ADC2BUF7 034E ADCx Data Buffer 7 xxxx

ADC2BUF8 0350 ADCx Data Buffer 8 xxxx

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

Note 1: These bits are not available on dsPIC33EP256MU806 devices.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 86  2009-2012 Microchip Technology Inc.

ADC2BUF9 0352 ADCx Data Buffer 9 xxxx

ADC2BUFA 0354 ADCx Data Buffer 10 xxxx

ADC2BUFB 0356 ADCx Data Buffer 11 xxxx

ADC2BUFC 0358 ADCx Data Buffer 12 xxxx

ADC2BUFD 035A ADCx Data Buffer 13 xxxx

ADC2BUFE 035C ADCx Data Buffer 14 xxxx

ADC2BUFF 035E ADCx Data Buffer 15 xxxx

AD2CON1 0360 ADON — ADSIDL ADDMABM —— FORM<1:0> SSRC<2:0> SSRCG SIMSAM ASAM SAMP DONE 0000

AD2CON2 0362 VCFG<2:0> —— CSCNA CHPS<1:0> BUFS — SMPI<3:0> BUFM ALTS 0000

AD2CON3 0364 ADRC —— SAMC<4:0> ADCS<7:0> 0000

AD2CHS123 0366 — — — — — CH123NB<1:0> CH123SB — — — — — CH123NA<1:0> CH123SA 0000

AD2CHS0 0368 CH0NB —— CH0SB<4:0> CH0NA ——CH0SA<4:0>0000

AD2CSSL 0270 CSS15 CSS14 CSS13 CSS12 CSS11 CSS10 CSS9 CSS8 CSS7 CSS6 CSS5 CSS4 CSS3 CSS2 CSS1 CSS0 0000

AD2CON4 0272 — — — — — — — ADDMAEN — — — — — DMABL<2:0> 0000

TABLE 4-25: ADC1 and ADC2 REGISTER MAP (CONTINUED)

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

Note 1: These bits are not available on dsPIC33EP256MU806 devices.

 2009-2012 Microchip Technology Inc. DS70616G-page 87

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-26: DCI REGISTER MAP

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

DCICON1 0280 DCIEN — DCISIDL — DLOOP CSCKD CSCKE COFSD UNFM CSDOM DJST — — — COFSM<1:0> 0000

DCICON2 0282 ———— BLEN<1:0> — COFSG<3:0> — WS<3:0> 0000

DCICON3 0284 ———— BCG<11:0> 0000

DCISTAT 0286 ———— SLOT<3:0> ———— ROV RFUL TUNF TMPTY 0000

TSCON 0288 TSE15 TSE14 TSE13 TSE12 TSE11 TSE10 TSE9 TSE8 TSE7 TSE6 TSE5 TSE4 TSE3 TSE2 TSE1 TSE0 0000

RSCON 028C RSE15 RSE14 RSE13 RSE12 RSE11 RSE10 RSE9 RSE8 RSE7 RSE6 RSE5 RSE4 RSE3 RSE2 RSE1 RSE0 0000

RXBUF0 0290 DCI Receive 0 Data Register uuuu

RXBUF1 0292 DCI Receive 1 Data Register uuuu

RXBUF2 0294 DCI Receive 2 Data Register uuuu

RXBUF3 0296 DCI Receive 3 Data Register uuuu

TXBUF0 0298 DCI Transmit 0 Data Register 0000

TXBUF1 029A DCI Transmit 1 Data Register 0000

TXBUF2 029C DCI Transmit 2 Data Register 0000

TXBUF3 029E DCI Transmit 3 Data Register 0000

Legend: x = unknown value on Reset, u = unchanged, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. Shaded locations indicate reserved space in the SFR map for future module

expansion. Read reserved locations as ‘0’s.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 88  2009-2012 Microchip Technology Inc.

TABLE 4-27: USB OTG REGISTER MAP FOR dsPIC33EPMU806/810/814 AND PIC24EPGU806/10/814) DEVICES ONLY

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

U1OTGIR 0488 — — — — — — — — IDIF T1MSECIF LSTATEIF ACTVIF SESVDIF SESENDIF —VBUSVDIF

0000

U1OTGIE 048A — — — — — — — — IDIE T1MSECIE LSTATEIE ACTVIE SESVDIE SESENDIE —VBUSVDIE

0000

U1OTGSTAT 048C — — — — — — — —ID —LSTATE— SESVD SESEND — VBUSVD

0000

U1OTGCON 048E — — — — — — — — DPPULUP DMPULUP DPPULDWN DMPULDWN VBUSON OTGEN VBUSCHG VBUSDIS

0000

U1PWRC 0490 — — — — — — — —UACTPND

(4)

——USLPGRD—— USUSPND USBPWR

0000

U1IR

(1)

04C0 — — — — — — — — STALLIF — RESUMEIF IDLEIF TRNIF SOFIF UERRIF URSTIF

0000

U1IR

(2)

04C0 — — — — — — — — STALLIF ATTACHIF RESUMEIF IDLEIF TRNIF SOFIF UERRIF DETACHIF

0000

U1IE

(1)

04C2 — — — — — — — — STALLIE — RESUMEIE IDLEIE TRNIE SOFIE UERRIE URSTIE

0000

U1IE

(2)

04C2 — — — — — — — — STALLIE ATTACHIE RESUMEIE IDLEIE TRNIE SOFIE UERRIE DETACHIE

0000

U1EIR

(1)

04C4 — — — — — — — — BTSEF BUSACCEF DMAEF BTOEF DFN8EF CRC16EF CRC5EF PIDEF

0000

U1EIR

(2)

04C4 — — — — — — — — BTSEF BUSACCEF DMAEF BTOEF DFN8EF CRC16EF EOFEF PIDEF

0000

U1EIE

(1)

04C6 — — — — — — — — BTSEE BUSACCEE DMAEE BTOEE DFN8EE CRC16EE CRC5EE PIDEE

0000

U1EIE

(2)

04C6 — — — — — — — — BTSEE BUSACCEE DMAEE BTOEE DFN8EE CRC16EE EOFEE PIDEE

0000

U1STAT 04C8 — — — — — — — —ENDPT<3:0>

(3)

DIR PPBI — —

0000

U1CON

(1)

04CA — — — — — — — — — SE0 PKTDIS — HOSTEN RESUME PPBRST USBEN

0000

U1CON

(2)

04CA — — — — — — — — JSTATE SE0 TOKBUSY USBRST HOSTEN RESUME PPBRST SOFEN

0000

U1ADDR 04CC — — — — — — — —LSPDEN

(1)

USB Device Address (DEVADDR)

0000

U1BDTP1 04CE — — — — — — — — BDTPTRL<15:9> —

0000

U1FRML 04D0 — — — — — — — — FRML<7:0>

0000

U1FRMH 04D2 — — — — — — — — — — — — — FRMH<2:0>

0000

U1TOK

(3)

04D4 — — — — — — — — PID<3:0> EP<3:0>

0000

U1SOF

(3)

04D6 — — — — — — — — CNT<7:0>

0000

U1BDTP2 04D8 — — — — — — — — BDTPTRH<23:16>

0000

U1BDTP3 04DA — — — — — — — — BDTPTRU<31:24>

0000

U1CNFG1 04DC — — — — — — — — UTEYE UOEMON — USBSIDL — — — —

0000

U1CNFG2 O4DE — — — — — — — — — — UVCMPSEL PUVBUS EXTI2CEN UVBUSDIS UVCMPDIS UTRDIS

0000

U1EP0 04E0 — — — — — — — —LSPDRETRYDIS — EPCONDIS EPRXEN EPTXEN EPSTALL EPHSHK

0000

U1EP1 04E2 — — — — — — — — — — — EPCONDIS EPRXEN EPTXEN EPSTALL EPHSHK

0000

U1EP2 04E4 — — — — — — — — — — — EPCONDIS EPRXEN EPTXEN EPSTALL EPHSHK

0000

U1EP3 04E6 — — — — — — — — — — — EPCONDIS EPRXEN EPTXEN EPSTALL EPHSHK

0000

U1EP4 04E8 — — — — — — — — — — — EPCONDIS EPRXEN EPTXEN EPSTALL EPHSHK

0000

Legend:

— = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

Note 1:

This bit is available when the module is operating in Device mode.

This bit is available when the module is operating in Host mode

Device mode only. These bits are always read as ‘

’ in Host mode.

The Reset value for this bit is undefined.

 2009-2012 Microchip Technology Inc. DS70616G-page 89

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U1EP5 04EA — — — — — — — — — — — EPCONDIS EPRXEN EPTXEN EPSTALL EPHSHK

0000

U1EP6 04EC — — — — — — — — — — — EPCONDIS EPRXEN EPTXEN EPSTALL EPHSHK

0000

U1EP7 04EE — — — — — — — — — — — EPCONDIS EPRXEN EPTXEN EPSTALL EPHSHK

0000

U1EP8 04F0 — — — — — — — — — — — EPCONDIS EPRXEN EPTXEN EPSTALL EPHSHK

0000

U1EP9 04F2 — — — — — — — — — — — EPCONDIS EPRXEN EPTXEN EPSTALL EPHSHK

0000

U1EP10 04F4 — — — — — — — — — — — EPCONDIS EPRXEN EPTXEN EPSTALL EPHSHK

0000

U1EP11 04F6 — — — — — — — — — — — EPCONDIS EPRXEN EPTXEN EPSTALL EPHSHK

0000

U1EP12 04F8 — — — — — — — — — — — EPCONDIS EPRXEN EPTXEN EPSTALL EPHSHK

0000

U1EP13 04FA — — — — — — — — — — — EPCONDIS EPRXEN EPTXEN EPSTALL EPHSHK

0000

U1EP14 04FC — — — — — — — — — — — EPCONDIS EPRXEN EPTXEN EPSTALL EPHSHK

0000

U1EP15 04FE — — — — — — — — — — — EPCONDIS EPRXEN EPTXEN EPSTALL EPHSHK

0000

U1PWMRRS 0580 DC<7:0> PER<7:0>

0000

U1PWMCON 0582 PWMEN — — — — — PWMPOL CNTEN — — — — — — — —

0000

TABLE 4-27: USB OTG REGISTER MAP FOR dsPIC33EPMU806/810/814 AND PIC24EPGU806/10/814) DEVICES ONLY (CONTINUED)

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend:

— = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

Note 1:

This bit is available when the module is operating in Device mode.

This bit is available when the module is operating in Host mode

Device mode only. These bits are always read as ‘

’ in Host mode.

The Reset value for this bit is undefined.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 90  2009-2012 Microchip Technology Inc.

TABLE 4-28: ECAN1 REGISTER MAP WHEN WIN (C1CTRL<0>) = 0 OR 1

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

C1CTRL1 0400 —— CSIDL ABAT CANCKS REQOP<2:0> OPMODE<2:0> — CANCAP ——WIN

0480

C1CTRL2 0402 — — — — — — — — — — — DNCNT<4:0>

0000

C1VEC 0404 ——— FILHIT<4:0> — ICODE<6:0>

0040

C1FCTRL 0406 DMABS<2:0> — — — — — — — —FSA<4:0>

0000

C1FIFO 0408 ——FBP<5:0> —— FNRB<5:0>

0000

C1INTF 040A —— TXBO TXBP RXBP TXWAR RXWAR EWARN IVRIF WAKIF ERRIF — FIFOIF RBOVIF RBIF TBIF

0000

C1INTE 040C — — — — — — — — IVRIE WAKIE ERRIE — FIFOIE RBOVIE RBIE TBIE

0000

C1EC 040E TERRCNT<7:0> RERRCNT<7:0>

0000

C1CFG1 0410 — — — — — — — — SJW<1:0> BRP<5:0>

0000

C1CFG2 0412 —WAKFIL— — — SEG2PH<2:0> SEG2PHTS SAM SEG1PH<2:0> PRSEG<2:0>

0000

C1FEN1 0414 FLTEN15 FLTEN14 FLTEN13 FLTEN12 FLTEN11 FLTEN10 FLTEN9 FLTEN8 FLTEN7 FLTEN6 FLTEN5 FLTEN4 FLTEN3 FLTEN2 FLTEN1 FLTEN0

FFFF

C1FMSKSEL1 0418 F7MSK<1:0> F6MSK<1:0> F5MSK<1:0> F4MSK<1:0> F3MSK<1:0> F2MSK<1:0> F1MSK<1:0> F0MSK<1:0>

0000

C1FMSKSEL2 041A F15MSK<1:0> F14MSK<1:0> F13MSK<1:0> F12MSK<1:0> F11MSK<1:0> F10MSK<1:0> F9MSK<1:0> F8MSK<1:0>

0000

Legend:

— = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

TABLE 4-29: ECAN1 REGISTER MAP WHEN WIN (C1CTRL<0>) = 0

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

— 0400-

041E

See Table 4-28 —

C1RXFUL1 0420 RXFUL15 RXFUL14 RXFUL13 RXFUL12 RXFUL11 RXFUL10 RXFUL9 RXFUL8 RXFUL7 RXFUL6 RXFUL5 RXFUL4 RXFUL3 RXFUL2 RXFUL1 RXFUL0

0000

C1RXFUL2 0422 RXFUL31 RXFUL30 RXFUL29 RXFUL28 RXFUL27 RXFUL26 RXFUL25 RXFUL24 RXFUL23 RXFUL22 RXFUL21 RXFUL20 RXFUL19 RXFUL18 RXFUL17 RXFUL16

0000

C1RXOVF1 0428 RXOVF15 RXOVF14 RXOVF13 RXOVF12 RXOVF11 RXOVF10 RXOVF9 RXOVF8 RXOVF7 RXOVF6 RXOVF5 RXOVF4 RXOVF3 RXOVF2 RXOVF1 RXOVF0

0000

C1RXOVF2 042A RXOVF31 RXOVF30 RXOVF29 RXOVF28 RXOVF27 RXOVF26 RXOVF25 RXOVF24 RXOVF23 RXOVF22 RXOVF21 RXOVF20 RXOVF19 RXOVF18 RXOVF17 RXOVF16

0000

C1TR01CON 0430 TXEN1 TXABT1 TXLARB1 TXERR1 TXREQ1 RTREN1 TX1PRI<1:0> TXEN0 TXABAT0 TXLARB0 TXERR0 TXREQ0 RTREN0 TX0PRI<1:0>

0000

C1TR23CON 0432 TXEN3 TXABT3 TXLARB3 TXERR3 TXREQ3 RTREN3 TX3PRI<1:0> TXEN2 TXABAT2 TXLARB2 TXERR2 TXREQ2 RTREN2 TX2PRI<1:0>

0000

C1TR45CON 0434 TXEN5 TXABT5 TXLARB5 TXERR5 TXREQ5 RTREN5 TX5PRI<1:0> TXEN4 TXABAT4 TXLARB4 TXERR4 TXREQ4 RTREN4 TX4PRI<1:0>

0000

C1TR67CON 0436 TXEN7 TXABT7 TXLARB7 TXERR7 TXREQ7 RTREN7 TX7PRI<1:0> TXEN6 TXABAT6 TXLARB6 TXERR6 TXREQ6 RTREN6 TX6PRI<1:0>

xxxx

C1RXD 0440 Received Data Word

xxxx

C1TXD 0442 Transmit Data Word

xxxx

Legend:

= unknown value on Reset, — = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 91

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-30: ECAN1 REGISTER MAP WHEN WIN (C1CTRL<0>) = 1

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

— 0400-

041E

See Table 4-28 —

C1BUFPNT1 0420 F3BP<3:0> F2BP<3:0> F1BP<3:0> F0BP<3:0>

0000

C1BUFPNT2 0422 F7BP<3:0> F6BP<3:0> F5BP<3:0> F4BP<3:0>

0000

C1BUFPNT3 0424 F11BP<3:0> F10BP<3:0> F9BP<3:0> F8BP<3:0>

0000

C1BUFPNT4 0426 F15BP<3:0> F14BP<3:0> F13BP<3:0> F12BP<3:0>

0000

C1RXM0SID 0430 SID<10:3> SID<2:0> —MIDE— EID<17:16>

xxxx

C1RXM0EID 0432 EID<15:8> EID<7:0>

xxxx

C1RXM1SID 0434 SID<10:3> SID<2:0> —MIDE— EID<17:16>

xxxx

C1RXM1EID 0436 EID<15:8> EID<7:0>

xxxx

C1RXM2SID 0438 SID<10:3> SID<2:0> —MIDE— EID<17:16>

xxxx

C1RXM2EID 043A EID<15:8> EID<7:0>

xxxx

C1RXF0SID 0440 SID<10:3> SID<2:0> —EXIDE— EID<17:16>

xxxx

C1RXF0EID 0442 EID<15:8> EID<7:0>

xxxx

C1RXF1SID 0444 SID<10:3> SID<2:0> —EXIDE— EID<17:16>

xxxx

C1RXF1EID 0446 EID<15:8> EID<7:0>

xxxx

C1RXF2SID 0448 SID<10:3> SID<2:0> —EXIDE— EID<17:16>

xxxx

C1RXF2EID 044A EID<15:8> EID<7:0>

xxxx

C1RXF3SID 044C SID<10:3> SID<2:0> —EXIDE— EID<17:16>

xxxx

C1RXF3EID 044E EID<15:8> EID<7:0>

xxxx

C1RXF4SID 0450 SID<10:3> SID<2:0> —EXIDE— EID<17:16>

xxxx

C1RXF4EID 0452 EID<15:8> EID<7:0>

xxxx

C1RXF5SID 0454 SID<10:3> SID<2:0> —EXIDE— EID<17:16>

xxxx

C1RXF5EID 0456 EID<15:8> EID<7:0>

xxxx

C1RXF6SID 0458 SID<10:3> SID<2:0> —EXIDE— EID<17:16>

xxxx

C1RXF6EID 045A EID<15:8> EID<7:0>

xxxx

C1RXF7SID 045C SID<10:3> SID<2:0> —EXIDE— EID<17:16>

xxxx

C1RXF7EID 045E EID<15:8> EID<7:0>

xxxx

C1RXF8SID 0460 SID<10:3> SID<2:0> —EXIDE— EID<17:16>

xxxx

C1RXF8EID 0462 EID<15:8> EID<7:0>

xxxx

C1RXF9SID 0464 SID<10:3> SID<2:0> —EXIDE— EID<17:16>

xxxx

C1RXF9EID 0466 EID<15:8> EID<7:0>

xxxx

C1RXF10SID 0468 SID<10:3> SID<2:0> —EXIDE— EID<17:16>

xxxx

C1RXF10EID 046A EID<15:8> EID<7:0>

xxxx

C1RXF11SID 046C SID<10:3> SID<2:0> —EXIDE— EID<17:16>

xxxx

Legend:

= unknown value on Reset, — = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 92  2009-2012 Microchip Technology Inc.

C1RXF11EID 046E EID<15:8> EID<7:0>

xxxx

C1RXF12SID 0470 SID<10:3> SID<2:0> —EXIDE— EID<17:16>

xxxx

C1RXF12EID 0472 EID<15:8> EID<7:0>

xxxx

C1RXF13SID 0474 SID<10:3> SID<2:0> —EXIDE— EID<17:16>

xxxx

C1RXF13EID 0476 EID<15:8> EID<7:0>

xxxx

C1RXF14SID 0478 SID<10:3> SID<2:0> —EXIDE— EID<17:16>

xxxx

C1RXF14EID 047A EID<15:8> EID<7:0>

xxxx

C1RXF15SID 047C SID<10:3> SID<2:0> —EXIDE— EID<17:16>

xxxx

C1RXF15EID 047E EID<15:8> EID<7:0>

xxxx

TABLE 4-30: ECAN1 REGISTER MAP WHEN WIN (C1CTRL<0>) = 1 (CONTINUED)

File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend:

= unknown value on Reset, — = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 93

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-31: ECAN2 REGISTER MAP WHEN WIN (C2CTRL<0>) = 0 OR 1

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

C2CTRL1 0500 —— CSIDL ABAT CANCKS REQOP<2:0> OPMODE<2:0> —CANCAP——WIN

0480

C2CTRL2 0502 — — — — — — — — — — — DNCNT<4:0>

0000

C2VEC 0504 ———FILHIT<4:0> —ICODE<6:0>

0040

C2FCTRL 0506 DMABS<2:0> — — — — — — — — FSA<4:0>

0000

C2FIFO 0508 ——FBP<5:0> ——FNRB<5:0>

0000

C2INTF 050A —— TXBO TXBP RXBP TXWAR RXWAR EWARN IVRIF WAKIF ERRIF — FIFOIF RBOVIF RBIF TBIF

0000

C2INTE 050C — — — — — — — — IVRIE WAKIE ERRIE — FIFOIE RBOVIE RBIE TBIE

0000

C2EC 050E TERRCNT<7:0> RERRCNT<7:0>

0000

C2CFG1 0510 — — — — — — — — SJW<1:0> BRP<5:0>

0000

C2CFG2 0512 —WAKFIL— — — SEG2PH<2:0> SEG2PHTS SAM SEG1PH<2:0> PRSEG<2:0>

0000

C2FEN1 0514 FLTEN15 FLTEN14 FLTEN13 FLTEN12 FLTEN11 FLTEN10 FLTEN9 FLTEN8 FLTEN7 FLTEN6 FLTEN5 FLTEN4 FLTEN3 FLTEN2 FLTEN1 FLTEN0

FFFF

C2FMSKSEL1 0518 F7MSK<1:0> F6MSK<1:0> F5MSK<1:0> F4MSK<1:0> F3MSK<1:0> F2MSK<1:0> F1MSK<1:0> F0MSK<1:0>

0000

C2FMSKSEL2 051A F15MSK<1:0> F14MSK<1:0> F13MSK<1:0> F12MSK<1:0> F11MSK<1:0> F10MSK<1:0> F9MSK<1:0> F8MSK<1:0>

0000

Legend:

— = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

TABLE 4-32: ECAN2 REGISTER MAP WHEN WIN (C2CTRL<0>) = 0

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

— 0500-

051E

See Table 4-31 —

C2RXFUL1 0520 RXFUL15 RXFUL14 RXFUL13 RXFUL12 RXFUL11 RXFUL10 RXFUL9 RXFUL8 RXFUL7 RXFUL6 RXFUL5 RXFUL4 RXFUL3 RXFUL2 RXFUL1 RXFUL0

0000

C2RXFUL2 0522 RXFUL31 RXFUL30 RXFUL29 RXFUL28 RXFUL27 RXFUL26 RXFUL25 RXFUL24 RXFUL23 RXFUL22 RXFUL21 RXFUL20 RXFUL19 RXFUL18 RXFUL17 RXFUL16

0000

C2RXOVF1 0528 RXOVF15 RXOVF14 RXOVF13 RXOVF12 RXOVF11 RXOVF10 RXOVF09 RXOVF08 RXOVF7 RXOVF6 RXOVF5 RXOVF4 RXOVF3 RXOVF2 RXOVF1 RXOVF0

0000

C2RXOVF2 052A RXOVF31 RXOVF30 RXOVF29 RXOVF28 RXOVF27 RXOVF26 RXOVF25 RXOVF24 RXOVF23 RXOVF22 RXOVF21 RXOVF20 RXOVF19 RXOVF18 RXOVF17 RXOVF16

0000

C2TR01CON 0530 TXEN1 TXABAT1 TXLARB1 TXERR1 TXREQ1 RTREN1 TX1PRI<1:0> TXEN0 TXABAT0 TXLARB0 TXERR0 TXREQ0 RTREN0 TX0PRI<1:0>

0000

C2TR23CON 0532 TXEN3 TXABAT3 TXLARB3 TXERR3 TXREQ3 RTREN3 TX3PRI<1:0> TXEN2 TXABAT2 TXLARB2 TXERR2 TXREQ2 RTREN2 TX2PRI<1:0>

0000

C2TR45CON 0534 TXEN5 TXABAT5 TXLARB5 TXERR5 TXREQ5 RTREN5 TX5PRI<1:0> TXEN4 TXABAT4 TXLARB4 TXERR4 TXREQ4 RTREN4 TX4PRI<1:0>

0000

C2TR67CON 0536 TXEN7 TXABAT7 TXLARB7 TXERR7 TXREQ7 RTREN7 TX7PRI<1:0> TXEN6 TXABAT6 TXLARB6 TXERR6 TXREQ6 RTREN6 TX6PRI<1:0>

xxxx

C2RXD 0540 ECAN2 Received Data Word

xxxx

C2TXD 0542 ECAN2 Transmit Data Word

xxxx

Legend:

= unknown value on Reset, — = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 94  2009-2012 Microchip Technology Inc.

TABLE 4-33: ECAN2 REGISTER MAP WHEN WIN (C2CTRL<0>) = 1

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

— 0500-

051E

See Table 4-31 —

C2BUFPNT1 0520 F3BP<3:0> F2BP<3:0> F1BP<3:0> F0BP<3:0> 0000

C2BUFPNT2 0522 F7BP<3:0> F6BP<3:0> F5BP<3:0> F4BP<3:0> 0000

C2BUFPNT3 0524 F11BP<3:0> F10BP<3:0> F9BP<3:0> F8BP<3:0> 0000

C2BUFPNT4 0526 F15BP<3:0> F14BP<3:0> F13BP<3:0> F12BP<3:0> 0000

C2RXM0SID 0530 SID<10:3> SID<2:0> —MIDE— EID<17:16> xxxx

C2RXM0EID 0532 EID<15:8> EID<7:0> xxxx

C2RXM1SID 0534 SID<10:3> SID<2:0> —MIDE— EID<17:16> xxxx

C2RXM1EID 0536 EID<15:8> EID<7:0> xxxx

C2RXM2SID 0538 SID<10:3> SID<2:0> —MIDE— EID<17:16> xxxx

C2RXM2EID 053A EID<15:8> EID<7:0> xxxx

C2RXF0SID 0540 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF0EID 0542 EID<15:8> EID<7:0> xxxx

C2RXF1SID 0544 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF1EID 0546 EID<15:8> EID<7:0> xxxx

C2RXF2SID 0548 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF2EID 054A EID<15:8> EID<7:0> xxxx

C2RXF3SID 054C SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF3EID 054E EID<15:8> EID<7:0> xxxx

C2RXF4SID 0550 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF4EID 0552 EID<15:8> EID<7:0> xxxx

C2RXF5SID 0554 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF5EID 0556 EID<15:8> EID<7:0> xxxx

C2RXF6SID 0558 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF6EID 055A EID<15:8> EID<7:0> xxxx

C2RXF7SID 055C SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF7EID 055E EID<15:8> EID<7:0> xxxx

C2RXF8SID 0560 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF8EID 0562 EID<15:8> EID<7:0> xxxx

C2RXF9SID 0564 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF9EID 0566 EID<15:8> EID<7:0> xxxx

C2RXF10SID 0568 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF10EID 056A EID<15:8> EID<7:0> xxxx

C2RXF11SID 056C SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 95

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

C2RXF11EID 056E EID<15:8> EID<7:0> xxxx

C2RXF12SID 0570 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF12EID 0572 EID<15:8> EID<7:0> xxxx

C2RXF13SID 0574 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF13EID 0576 EID<15:8> EID<7:0> xxxx

C2RXF14SID 0578 SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF14EID 057A EID<15:8> EID<7:0> xxxx

C2RXF15SID 057C SID<10:3> SID<2:0> — EXIDE — EID<17:16> xxxx

C2RXF15EID 057E EID<15:8> EID<7:0> xxxx

TABLE 4-33: ECAN2 REGISTER MAP WHEN WIN (C2CTRL<0>) = 1 (CONTINUED)

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 96  2009-2012 Microchip Technology Inc.

TABLE 4-35: CRC REGISTER MAP

TABLE 4-34: PARALLEL MASTER/SLAVE PORT REGISTER MAP

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

PMCON 0600 PMPEN — PSIDL ADRMUX<1:0> PTBEEN PTWREN PTRDEN CSF<1:0> ALP CS2P CS1P BEP WRSP RDSP

0000

PMMODE 0602 BUSY IRQM<1:0> INCM<1:0> MODE16 MODE<1:0> WAITB<1:0> WAITM<3:0> WAITE<1:0>

0000

PMADDR

(1)

0604 CS2 CS1 Parallel Port Address (ADDR<13:0>)

0000

PMDOUT1

(1)

0604 Parallel Port Data Out Register 1 (Buffers Level 0 and 1)

0000

PMDOUT2 0606 Parallel Port Data Out Register 2 (Buffers Level 2 and 3)

0000

PMDIN1 0608 Parallel Port Data In Register 1 (Buffers Level 0 and 1)

0000

PMDIN2 060A Parallel Port Data In Register 2 (Buffers Level 2 and 3)

0000

PMAEN 060C PTEN15 PTEN14 PTEN13 PTEN12 PTEN11 PTEN10 PTEN9 PTEN8 PTEN7 PTEN6 PTEN5 PTEN4 PTEN3 PTEN2 PTEN1 PTEN0

0000

PMSTAT 060E IBF IBOV —— IB3F IB2F IB1F IB0F OBE OBUF —— OB3E OB2E OB1E OB0E

008F

Legend:

— = unimplemented, read as ‘

’. Shaded bits are not used in the operation of the PMP module.

Note 1:

PMADDR and PMDOUT1 are the same physical register, but are defined differently depending on the module’s operating mode.

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

CRCCON1 0640 CRCEN — CSIDL VWORD<4:0> CRCFUL CRCMPT CRCISEL CRCGO LENDIAN — — — 0000

CRCCON2 0642 — — — DWIDTH<4:0> — — — PLEN<4:0> 0000

CRCXORL 0644 X<15:1> —0000

CRCXORH 0646 X<31:16> 0000

CRCDATL 0648 CRC Data Input Low Word 0000

CRCDATH 064A CRC Data Input High Word 0000

CRCWDATL 064C CRC Result Low Word 0000

CRCWDATH 064E CRC Result High Word 0000

Legend: — = unimplemented, read as ‘0’. Shaded bits are not used in the operation of the programmable CRC module.

TABLE 4-36: REAL-TIME CLOCK AND CALENDAR REGISTER MAP

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

ALRMVAL 0620 Alarm Value Register Window based on ALRMPTR<1:0>

xxxx

ALCFGRPT 0622 ALRMEN CHIME AMASK<3:0> ALRMPTR<1:0> ARPT<7:0>

0000

RTCVAL 0624 RTCC Value Register Window based on RTCPTR<1:0>

xxxx

RCFGCAL 0626 RTCEN — RTCWREN RTCSYNC HALFSEC RTCOE RTCPTR<1:0> CAL<7:0>

0000

Legend:

= unknown value on Reset, — = unimplemented, read as ‘

’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 97

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-37: PERIPHERAL PIN SELECT OUTPUT REGISTER MAP FOR dsPIC33EPXXXMU810/814 AND PIC24EPXXXGU810/814

DEVICES ONLY

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

RPOR0 0680 —— RP65R<5:0> ——RP64R<5:0>0000

RPOR1 0682 —— RP67R<5:0> ——RP66R<5:0>0000

RPOR2 0684 —— RP69R<5:0> ——RP68R<5:0>0000

RPOR3 0686 —— RP71R<5:0> ——RP70R<5:0>0000

RPOR4 0688 —— RP80R<5:0> ——RP79R<5:0>0000

RPOR5 068A —— RP84R<5:0> ——RP82R<5:0>0000

RPOR6 068C —— RP87R<5:0> ——RP85R<5:0>0000

RPOR7 068E —— RP97R<5:0> ——RP96R<5:0>0000

RPOR8 0690 —— RP99R<5:0> ——RP98R<5:0>0000

RPOR9 0692 —— RP101R<5:0> —— RP100R<5:0> 0000

RPOR11 0696 —— RP108R<5:0> —— RP104R<5:0> 0000

RPOR12 0698 —— RP112R<5:0> —— RP109R<5:0> 0000

RPOR13 069A —— RP118R<5:0> —— RP113R<5:0> 0000

RPOR14 069C —— RP125R<5:0> —— RP120R<5:0> 0000

RPOR15 069E —— RP127R<5:0> —— RP126R<5:0> 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 98  2009-2012 Microchip Technology Inc.

TABLE 4-38: PERIPHERAL PIN SELECT OUTPUT REGISTER MAP FOR dsPIC33EPXXXMU806 DEVICES ONLY

TABLE 4-39: PERIPHERAL PIN SELECT OUTPUT REGISTER MAP FOR dsPIC33EPXXX(GP/MC/MU)806 AND PIC24EPXXXGP806

DEVICES ONLY

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

RPOR0 0680 ——RP65R<5:0>—— RP64R<5:0> 0000

RPOR1 0682 ——RP67R<5:0>—— RP66R<5:0> 0000

RPOR2 0684 ——RP69R<5:0>—— RP68R<5:0> 0000

RPOR3 0686 ——RP71R<5:0>—— RP70R<5:0> 0000

RPOR4 0688 ——RP80R<5:0>— — — — — — — — 0000

RPOR5 068A ——RP84R<5:0>—— RP82R<5:0> 0000

RPOR6 068C ——RP87R<5:0>—— RP85R<5:0> 0000

RPOR7 068E ——RP97R<5:0>—— RP96R<5:0> 0000

RPOR8 0690 ——RP99R<5:0>— — — — — — — — 0000

RPOR9 0692 —— RP101R<5:0> —— RP100R<5:0> 0000

RPOR13 069A —— RP118R<5:0> — — — — — — — — 0000

RPOR14 069C —————————— RP120R<5:0> 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

RPOR0 0680 ——RP65R<5:0>—— RP64R<5:0> 0000

RPOR1 0682 ——RP67R<5:0>—— RP66R<5:0> 0000

RPOR2 0684 ——RP69R<5:0>—— RP68R<5:0> 0000

RPOR3 0686 ——RP71R<5:0>—— RP70R<5:0> 0000

RPOR4 0688 ——RP80R<5:0>— — — — — — — — 0000

RPOR5 068A ——RP84R<5:0>—— RP82R<5:0> 0000

RPOR6 068C ——RP87R<5:0>—— RP85R<5:0> 0000

RPOR7 068E ——RP97R<5:0>—— RP96R<5:0> 0000

RPOR8 0690 ——RP99R<5:0>—— RP98R<5:0> 0000

RPOR9 0692 —— RP101R<5:0> —— RP100R<5:0> 0000

RPOR10 0694 —————————— RP102R<5:0> 0000

RPOR13 069A —— RP118R<5:0> — — — — — — — — 0000

RPOR14 069C —————————— RP120R<5:0> 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 99

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-40: PERIPHERAL PIN SELECT INPUT REGISTER MAP FOR dsPIC33EPXXXMU814 DEVICES ONLY

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

RPINR0 06A0 —INT1R<6:0> — — — — — — — — 0000

RPINR1 06A2 —INT3R<6:0> —INT2R<6:0>0000

RPINR2 06A4 — — — — — — — — —INT4R<6:0>0000

RPINR3 06A6 —T3CKR<6:0> —T2CKR<6:0>0000

RPINR4 06A8 —T5CKR<6:0> —T4CKR<6:0>0000

RPINR5 06AA —T7CKR<6:0> —T6CKR<6:0>0000

RPINR6 06AC —T9CKR<6:0> —T8CKR<6:0>0000

RPINR7 06AE —IC2R<6:0> —IC1R<6:0>0000

RPINR8 06B0 —IC4R<6:0> —IC3R<6:0>0000

RPINR9 06B2 —IC6R<6:0> —IC5R<6:0>0000

RPINR10 06B4 —IC8R<6:0> —IC7R<6:0>0000

RPINR11 06B6 —OCFBR<6:0> —OCFAR<6:0>0000

RPINR12 06B8 —FLT2R<6:0> —FLT1R<6:0>0000

RPINR13 06BA —FLT4R<6:0> —FLT3R<6:0>0000

RPINR14 06BC —QEB1R<6:0> —QEA1R<6:0>0000

RPINR15 06BE —HOME1R<6:0> — INDX1R<6:0> 0000

RPINR16 06C0 —QEB2R<6:0> —QEA2R<6:0>0000

RPINR17 06C2 —HOME2R<6:0> — INDX2R<6:0> 0000

RPINR18 06C4 — U1CTSR<6:0> —U1RXR<6:0>0000

RPINR19 06C6 — U2CTSR<6:0> —U2RXR<6:0>0000

RPINR20 06C8 —SCK1R<6:0> —SDI1R<6:0>0000

RPINR21 06CA — — — — — — — — —SS1R<6:0>0000

RPINR23 06CE — — — — — — — — —SS2R<6:0>0000

RPINR24 06D0 — CSCKR<6:0> — CSDIR<6:0> 0000

RPINR25 06D2 — — — — — — — — —COFSR<6:0>0000

RPINR26 06D4 —C2RXR<6:0> —C1RXR<6:0>0000

RPINR27 06D6 — U3CTSR<6:0> —U3RXR<6:0>0000

RPINR28 06D8 — U4CTSR<6:0> —U4RXR<6:0>0000

RPINR29 06DA —SCK3R<6:0> —SDI3R<6:0>0000

RPINR30 06DC — — — — — — — — —SS3R<6:0>0000

RPINR31 06DE —SCK4R<6:0> —SDI4R<6:0>0000

RPINR32 06E0 — — — — — — — — —SS4R<6:0>0000

RPINR33 06E2 —IC10R<6:0> —IC9R<6:0>0000

RPINR34 06E4 —IC12R<6:0> —IC11R<6:0>0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 100  2009-2012 Microchip Technology Inc.

RPINR35 06E6 —IC14R<6:0> — IC13R<6:0> 0000

RPINR36 06E8 —IC16R<6:0> — IC15R<6:0> 0000

RPINR37 06EA —SYNCI1R<6:0> —OCFCR<6:0>0000

RPINR38 06EC —DTCMP1R<6:0> — SYNCI2R<6:0> 0000

RPINR39 06EE —DTCMP3R<6:0> —DTCMP2R<6:0>0000

RPINR40 06F0 —DTCMP5R<6:0> —DTCMP4R<6:0>0000

RPINR41 06F2 —DTCMP7R<6:0> —DTCMP6R<6:0>0000

RPINR42 06F4 —FLT6R<6:0> —FLT5R<6:0>0000

RPINR43 06F6 — — — — — — — — —FLT7R<6:0>0000

TABLE 4-40: PERIPHERAL PIN SELECT INPUT REGISTER MAP FOR dsPIC33EPXXXMU814 DEVICES ONLY (CONTINUED)

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 101

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-41: PERIPHERAL PIN SELECT INPUT REGISTER MAP FOR dsPIC33EPXXXMU810 DEVICES ONLY

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

RPINR0 06A0 —INT1R<6:0> ————————0000

RPINR1 06A2 —INT3R<6:0> —INT2R<6:0>0000

RPINR2 06A4 — — — — — — — — —INT4R<6:0>0000

RPINR3 06A6 —T3CKR<6:0> —T2CKR<6:0>0000

RPINR4 06A8 —T5CKR<6:0> —T4CKR<6:0>0000

RPINR5 06AA —T7CKR<6:0> —T6CKR<6:0>0000

RPINR6 06AC —T9CKR<6:0> —T8CKR<6:0>0000

RPINR7 06AE —IC2R<6:0> — IC1R<6:0> 0000

RPINR8 06B0 —IC4R<6:0> — IC3R<6:0> 0000

RPINR9 06B2 —IC6R<6:0> — IC5R<6:0> 0000

RPINR10 06B4 —IC8R<6:0> — IC7R<6:0> 0000

RPINR11 06B6 —OCFBR<6:0> —OCFAR<6:0>0000

RPINR12 06B8 —FLT2R<6:0> —FLT1R<6:0>0000

RPINR13 06BA —FLT4R<6:0> —FLT3R<6:0>0000

RPINR14 06BC —QEB1R<6:0> —QEA1R<6:0>0000

RPINR15 06BE — HOME1R<6:0> — INDX1R<6:0> 0000

RPINR16 06C0 —QEB2R<6:0> —QEA2R<6:0>0000

RPINR17 06C2 — HOME2R<6:0> — INDX2R<6:0> 0000

RPINR18 06C4 — U1CTSR<6:0> —U1RXR<6:0>0000

RPINR19 06C6 — U2CTSR<6:0> —U2RXR<6:0>0000

RPINR20 06C8 —SCK1R<6:0> —SDI1R<6:0>0000

RPINR21 06CA — — — — — — — — — SS1R<6:0> 0000

RPINR23 06CE — — — — — — — — — SS2R<6:0> 0000

RPINR24 06D0 —CSCKR<6:0> —CSDIR<6:0>0000

RPINR25 06D2 — — — — — — — — — COFSINR<6:0> 0000

RPINR26 06D4 —C2RXR<6:0> —C1RXR<6:0>0000

RPINR27 06D6 — U3CTSR<6:0> —U3RXR<6:0>0000

RPINR28 06D8 — U4CTSR<6:0> —U4RXR<6:0>0000

RPINR29 06DA —SCK3R<6:0> —SDI3R<6:0>0000

RPINR30 06DC — — — — — — — — — SS3R<6:0> 0000

RPINR31 06DE —SCK4R<6:0> —SDI4R<6:0>0000

RPINR32 06E0 — — — — — — — — — SS4R<6:0> 0000

RPINR33 06E2 —IC10R<6:0> — IC9R<6:0> 0000

RPINR34 06E4 —IC12R<6:0> —IC11R<6:0>0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 102  2009-2012 Microchip Technology Inc.

RPINR35 06E6 —IC14R<6:0> —IC13R<6:0>0000

RPINR36 06E8 —IC16R<6:0> —IC15R<6:0>0000

RPINR37 06EA —SYNCI1R<6:0> — OCFCR<6:0> 0000

RPINR38 06EC —DTCMP1R<6:0> —SYNCI2R<6:0>0000

RPINR39 06EE —DTCMP3R<6:0> —DTCMP2R<6:0>0000

RPINR40 06F0 —DTCMP5R<6:0> —DTCMP4R<6:0>0000

RPINR41 06F2 — — — — — — — — —DTCMP6R<6:0>0000

RPINR42 06F4 —FLT6R<6:0> —FLT5R<6:0>0000

RPINR43 06F6 — — — — — — — — —FLT7R<6:0>0000

TABLE 4-41: PERIPHERAL PIN SELECT INPUT REGISTER MAP FOR dsPIC33EPXXXMU810 DEVICES ONLY (CONTINUED)

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 103

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-42: PERIPHERAL PIN SELECT INPUT REGISTER MAP FOR dsPIC33EPXXX(MC/MU)806 DEVICES ONLY

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

RPINR0 06A0 —INT1R<6:0> — — — — — — — — 0000

RPINR1 06A2 —INT3R<6:0> —INT2R<6:0>0000

RPINR2 06A4 — — — — — — — — —INT4R<6:0>0000

RPINR3 06A6 —T3CKR<6:0> —T2CKR<6:0>0000

RPINR4 06A8 —T5CKR<6:0> —T4CKR<6:0>0000

RPINR5 06AA —T7CKR<6:0> —T6CKR<6:0>0000

RPINR6 06AC —T9CKR<6:0> —T8CKR<6:0>0000

RPINR7 06AE —IC2R<6:0> — IC1R<6:0> 0000

RPINR8 06B0 —IC4R<6:0> — IC3R<6:0> 0000

RPINR9 06B2 —IC6R<6:0> — IC5R<6:0> 0000

RPINR10 06B4 —IC8R<6:0> — IC7R<6:0> 0000

RPINR11 06B6 —OCFBR<6:0> —OCFAR<6:0>0000

RPINR12 06B8 —FLT2R<6:0> —FLT1R<6:0>0000

RPINR13 06BA —FLT4R<6:0> —FLT3R<6:0>0000

RPINR14 06BC — QEB1R<6:0> —QEA1R<6:0>0000

RPINR15 06BE —HOME1R<6:0> — INDX1R<6:0> 0000

RPINR16 06C0 — QEB2R<6:0> —QEA2R<6:0>0000

RPINR17 06C2 —HOME2R<6:0> — INDX2R<6:0> 0000

RPINR18 06C4 —U1CTSR<6:0> —U1RXR<6:0>0000

RPINR19 06C6 —U2CTSR<6:0> —U2RXR<6:0>0000

RPINR20 06C8 —SCK1R<6:0> —SDI1R<6:0>0000

RPINR21 06CA — — — — — — — — — SS1R<6:0> 0000

RPINR23 06CE — — — — — — — — — SS2R<6:0> 0000

RPINR24 06D0 —CSCKR<6:0> —CSDIR<6:0>0000

RPINR25 06D2 — — — — — — — — — COFSINR<6:0> 0000

RPINR26 06D4 —C2RXR<6:0> —C1RXR<6:0>0000

RPINR27 06D6 —U3CTSR<6:0> —U3RXR<6:0>0000

RPINR28 06D8 —U4CTSR<6:0> —U4RXR<6:0>0000

RPINR29 06DA —SCK3R<6:0> —SDI3R<6:0>0000

RPINR30 06DC — — — — — — — — — SS3R<6:0> 0000

RPINR31 06DE —SCK4R<6:0> —SDI4R<6:0>0000

RPINR32 06E0 — — — — — — — — — SS4R<6:0> 0000

RPINR33 06E2 —IC10R<6:0> — IC9R<6:0> 0000

RPINR34 06E4 —IC12R<6:0> —IC11R<6:0>0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 104  2009-2012 Microchip Technology Inc.

RPINR35 06E6 —IC14R<6:0> —IC13R<6:0>0000

RPINR36 06E8 —IC16R<6:0> —IC15R<6:0>0000

RPINR37 06EA — SYNCI1R<6:0> — OCFCR<6:0> 0000

RPINR38 06EC —DTCMP1R<6:0> — SYNCI2R<6:0> 0000

RPINR39 06EE —DTCMP3R<6:0> —DTCMP2R<6:0>0000

RPINR40 06F0 — — — — — — — — —DTCMP4R<6:0>0000

RPINR42 06F4 —FLT6R<6:0> —FLT5R<6:0>0000

RPINR43 06F6 — — — — — — — — —FLT7R<6:0>0000

TABLE 4-42: PERIPHERAL PIN SELECT INPUT REGISTER MAP FOR dsPIC33EPXXX(MC/MU)806 DEVICES ONLY (CONTINUED)

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 105

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-43: PERIPHERAL PIN SELECT INPUT REGISTER MAP FOR PIC24EPXXXGU810/814 DEVICES ONLY

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

All

Reset

RPINR0 06A0 —INT1R<6:0> — ———————0000

RPINR1 06A2 —INT3R<6:0> —INT2R<6:0>0000

RPINR2 06A4 — — — — — — — — —INT4R<6:0>0000

RPINR3 06A6 —T3CKR<6:0> —T2CKR<6:0>0000

RPINR4 06A8 —T5CKR<6:0> —T4CKR<6:0>0000

RPINR5 06AA —T7CKR<6:0> —T6CKR<6:0>0000

RPINR6 06AC —T9CKR<6:0> —T8CKR<6:0>0000

RPINR7 06AE — IC2R<6:0> — IC1R<6:0> 0000

RPINR8 06B0 — IC4R<6:0> — IC3R<6:0> 0000

RPINR9 06B2 — IC6R<6:0> — IC5R<6:0> 0000

RPINR10 06B4 — IC8R<6:0> — IC7R<6:0> 0000

RPINR11 06B6 —OCFBR<6:0> —OCFAR<6:0>0000

RPINR18 06C4 — U1CTSR<6:0> —U1RXR<6:0>0000

RPINR19 06C6 — U2CTSR<6:0> —U2RXR<6:0>0000

RPINR20 06C8 —SCK1R<6:0> —SDI1R<6:0>0000

RPINR21 06CA — — — — — — — — — SS1R<6:0> 0000

RPINR23 06CE — — — — — — — — — SS2R<6:0> 0000

RPINR26 06D4 —C2RXR<6:0> —C1RXR<6:0>0000

RPINR27 06D6 — U3CTSR<6:0> —U3RXR<6:0>0000

RPINR28 06D8 — U4CTSR<6:0> —U4RXR<6:0>0000

RPINR29 06DA —SCK3R<6:0> —SDI3R<6:0>0000

RPINR30 06DC — — — — — — — — — SS3R<6:0> 0000

RPINR31 06DE —SCK4R<6:0> —SDI4R<6:0>0000

RPINR32 06E0 — — — — — — — — — SS4R<6:0> 0000

RPINR33 06E2 —IC10R<6:0> — IC9R<6:0> 0000

RPINR34 06E4 —IC12R<6:0> —IC11R<6:0>0000

RPINR35 06E6 —IC14R<6:0> —IC13R<6:0>0000

RPINR36 06E8 —IC16R<6:0> —IC15R<6:0>0000

RPINR37 06EA — — — — — — — — — OCFCR<6:0> 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 106  2009-2012 Microchip Technology Inc.

TABLE 4-44: REFERENCE CLOCK REGISTER MAP

TABLE 4-45: NVM REGISTER MAP

TABLE 4-46: SYSTEM CONTROL REGISTER MAP

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

REFOCON 074E ROON — ROSSLP ROSEL RODIV<3:0> — — — — — — — — 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

NVMCON 0728 WR WREN WRERR NVMSIDL — — — — — — — — NVMOP<3:0> 0000

NVMADR 072A NVMADR<15:0> 0000

NVMADRU 072C — — — — — — — — NVMADR<23:16> 0000

NVMKEY 072E — — — — — — — — NVMKEY<7:0> 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

RCON 0740 TRAPR IOPUWR ——VREGSF — CM VREGS EXTR SWR SWDTEN WDTO SLEEP IDLE BOR POR Note 1

OSCCON 0742 — COSC<2:0> — NOSC<2:0> CLKLOCK IOLOCK LOCK —CF— LPOSCEN OSWEN Note 2

CLKDIV 0744 ROI DOZE<2:0> DOZEN FRCDIV<2:0> PLLPOST<1:0> — PLLPRE<4:0> 3040

PLLFBD 0746 — — — — — — — PLLDIV<8:0> 0030

OSCTUN 0748 — — — — — — — — — — TUN<5:0> 0000

ACLKCON3 0758 ENAPLL — SELACLK AOSCMD<1:0> ASRCSEL FRCSEL — APLLPOST2<2:0> —— APLLPRE<2:0> 0000

ACLKDIV3 075A — — — — — — — — — — — — — APLLDIV<2:0> 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

Note 1: RCON register Reset values are dependent on the type of Reset.

2: OSCCON register Reset values are dependent on the Configuration Fuses and by the type of Reset.

 2009-2012 Microchip Technology Inc. DS70616G-page 107

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-47: PMD REGISTER MAP FOR dsPIC33EPXXXMU814 DEVICES ONLY

TABLE 4-48: PMD REGISTER MAP FOR dsPIC33EPXXXMU810 DEVICES ONLY

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

PMD1 0760 T5MD T4MD T3MD T2MD T1MD QEI1MD PWMMD DCIMD I2C1MD U2MD U1MD SPI2MD SPI1MD C2MD C1MD AD1MD 0000

PMD2 0762 IC8MD IC7MD IC6MD IC5MD IC4MD IC3MD IC2MD IC1MD OC8MD OC7MD OC6MD OC5MD OC4MD OC3MD OC2MD OC1MD 0000

PMD3 0764 T9MD T8MD T7MD T6MD — CMPMD RTCCMD PMPMD CRCMD —QEI2MD—U3MD—I2C2MDAD2MD0000

PMD4 0766 — — — — — — — — — —U4MD—REFOMD—— USB1MD 0000

PMD5 0768 IC16MD IC15MD IC14MD IC13MD IC12MD IC11MD IC10MD IC9MD OC16MD OC15MD OC14MD OC13MD OC12MD OC11MD OC10MD OC9MD 0000

PMD6 076A — PWM7MD PWM6MD PWM5MD PWM4MD PWM3MD PWM2MD PWM1MD — — — — — — SPI4MD SPI3MD 0000

PMD7 076C

————— — —— DMA12MD DMA8MD DMA4MD DMA0MD — — — — 0000

————— — —— DMA13MD DMA9MD DMA5MD DMA1MD — — — — 0000

————— — —— DMA14MD DMA10MD DMA6MD DMA2MD — — — — 0000

— — — — — — — — — DMA11MD DMA7MD DMA3MD — — — — 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

PMD1 0760 T5MD T4MD T3MD T2MD T1MD QEI1MD PWMMD DCIMD I2C1MD U2MD U1MD SPI2MD SPI1MD C2MD C1MD AD1MD 0000

PMD2 0762 IC8MD IC7MD IC6MD IC5MD IC4MD IC3MD IC2MD IC1MD OC8MD OC7MD OC6MD OC5MD OC4MD OC3MD OC2MD OC1MD 0000

PMD3 0764 T9MD T8MD T7MD T6MD — CMPMD RTCCMD PMPMD CRCMD —QEI2MD—U3MD— I2C2MD AD2MD 0000

PMD4 0766 — — — — — — — — — —U4MD—REFOMD——USB1MD0000

PMD5 0768 IC16MD IC15MD IC14MD IC13MD IC12MD IC11MD IC10MD IC9MD OC16MD OC15MD OC14MD OC13MD OC12MD OC11MD OC10MD OC9MD 0000

PMD6 076A —— PWM6MD PWM5MD PWM4MD PWM3MD PWM2MD PWM1MD — — — — — — SPI4MD SPI3MD 0000

PMD7 076C

— — — — — — — — DMA12MD DMA8MD DMA4MD DMA0MD — — — — 0000

— — — — — — — — DMA13MD DMA9MD DMA5MD DMA1MD — — — — 0000

— — — — — — — — DMA14MD DMA10MD DMA6MD DMA2MD — — — — 0000

— — — — — — — — — DMA11MD DMA7MD DMA3MD — — — — 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 108  2009-2012 Microchip Technology Inc.

TABLE 4-49: PMD REGISTER MAP FOR dsPIC33EPXXXMU806 DEVICES ONLY

TABLE 4-50: PMD REGISTER MAP FOR dsPIC33EPXXXMC806 DEVICES ONLY

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

PMD1 0760 T5MD T4MD T3MD T2MD T1MD QEI1MD PWMMD DCIMD I2C1MD U2MD U1MD SPI2MD SPI1MD C2MD C1MD AD1MD 0000

PMD2 0762 IC8MD IC7MD IC6MD IC5MD IC4MD IC3MD IC2MD IC1MD OC8MD OC7MD OC6MD OC5MD OC4MD OC3MD OC2MD OC1MD 0000

PMD3 0764 T9MD T8MD T7MD T6MD — CMPMD RTCCMD PMPMD CRCMD —QEI2MD—U3MD—I2C2MDAD2MD0000

PMD4 0766 — — — — — — — — — —U4MD—REFOMD——USB1MD0000

PMD5 0768 IC16MD IC15MD IC14MD IC13MD IC12MD IC11MD IC10MD IC9MD OC16MD OC15MD OC14MD OC13MD OC12MD OC11MD OC10MD OC9MD 0000

PMD6 076A ———— PWM4MD PWM3MD PWM2MD PWM1MD — — ———— SPI4MD SPI3MD 0000

PMD7 076C

— — — — — — — — DMA12MD DMA8MD DMA4MD DMA0MD — — — — 0000

— — — — — — — — DMA13MD DMA9MD DMA5MD DMA1MD — — — — 0000

— — — — — — — — DMA14MD DMA10MD DMA6MD DMA2MD — — — — 0000

— — — — — — — — — DMA11MD DMA7MD DMA3MD — — — — 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

PMD1 0760 T5MD T4MD T3MD T2MD T1MD QEI1MD PWMMD DCIMD I2C1MD U2MD U1MD SPI2MD SPI1MD C2MD C1MD AD1MD 0000

PMD2 0762 IC8MD IC7MD IC6MD IC5MD IC4MD IC3MD IC2MD IC1MD OC8MD OC7MD OC6MD OC5MD OC4MD OC3MD OC2MD OC1MD 0000

PMD3 0764 T9MD T8MD T7MD T6MD — CMPMD RTCCMD PMPMD CRCMD —QEI2MD—U3MD—I2C2MDAD2MD0000

PMD4 0766 — — — — — — — — — —U4MD—REFOMD— — — 0000

PMD5 0768 IC16MD IC15MD IC14MD IC13MD IC12MD IC11MD IC10MD IC9MD OC16MD OC15MD OC14MD OC13MD OC12MD OC11MD OC10MD OC9MD 0000

PMD6 076A ———— PWM4MD PWM3MD PWM2MD PWM1MD — — ———— SPI4MD SPI3MD 0000

PMD7 076C

— — — — — — — — DMA12MD DMA8MD DMA4MD DMA0MD — — — — 0000

— — — — — — — — DMA13MD DMA9MD DMA5MD DMA1MD — — — — 0000

— — — — — — — — DMA14MD DMA10MD DMA6MD DMA2MD — — — — 0000

— — — — — — — — — DMA11MD DMA7MD DMA3MD — — — — 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 109

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-51: PMD REGISTER MAP FOR dsPIC33EPXXXGP8XX AND PIC24EPXXXGP8XX DEVICES ONLY

TABLE 4-52: PMD REGISTER MAP FOR PIC24EPXXXGU810/814 DEVICES ONLY

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

PMD1 0760 T5MD T4MD T3MD T2MD T1MD —— DCIMD I2C1MD U2MD U1MD SPI2MD SPI1MD C2MD C1MD AD1MD 0000

PMD2 0762 IC8MD IC7MD IC6MD IC5MD IC4MD IC3MD IC2MD IC1MD OC8MD OC7MD OC6MD OC5MD OC4MD OC3MD OC2MD OC1MD 0000

PMD3 0764 T9MD T8MD T7MD T6MD — CMPMD RTCCMD PMPMD CRCMD — — —U3MD— I2C2MD AD2MD 0000

PMD4 0766 — — — — — — — — — —U4MD—REFOMD— — — 0000

PMD5 0768 IC16MD IC15MD IC14MD IC13MD IC12MD IC11MD IC10MD IC9MD OC16MD OC15MD OC14MD OC13MD OC12MD OC11MD OC10MD OC9MD 0000

PMD6 076A — — — — — — — — — — — — — — SPI4MD SPI3MD 0000

PMD7 076C

— — — — — — — — DMA12MD DMA8MD DMA4MD DMA0MD — — — — 0000

— — — — — — — — DMA13MD DMA9MD DMA5MD DMA1MD — — — — 0000

— — — — — — — — DMA14MD DMA10MD DMA6MD DMA2MD — — — — 0000

— — — — — — — — — DMA11MD DMA7MD DMA3MD — — — — 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

PMD1 0760 T5MD T4MD T3MD T2MD T1MD —— DCIMD I2C1MD U2MD U1MD SPI2MD SPI1MD C2MD C1MD AD1MD 0000

PMD2 0762 IC8MD IC7MD IC6MD IC5MD IC4MD IC3MD IC2MD IC1MD OC8MD OC7MD OC6MD OC5MD OC4MD OC3MD OC2MD OC1MD 0000

PMD3 0764 T9MD T8MD T7MD T6MD — CMPMD RTCCMD PMPMD CRCMD — — —U3MD— I2C2MD AD2MD 0000

PMD4 0766 — — — — — — — — — —U4MD—REFOMD——USB1MD0000

PMD5 0768 IC16MD IC15MD IC14MD IC13MD IC12MD IC11MD IC10MD IC9MD OC16MD OC15MD OC14MD OC13MD OC12MD OC11MD OC10MD OC9MD 0000

PMD6 076A — — — — — — — — — — — — — — SPI4MD SPI3MD 0000

PMD7 076C

— — — — — — — — DMA12MD DMA8MD DMA4MD DMA0MD — — — — 0000

— — — — — — — — DMA13MD DMA9MD DMA5MD DMA1MD — — — — 0000

— — — — — — — — DMA14MD DMA10MD DMA6MD DMA2MD — — — — 0000

— — — — — — — — — DMA11MD DMA7MD DMA3MD — — — — 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 110  2009-2012 Microchip Technology Inc.

TABLE 4-53: COMPARATOR REGISTER MAP

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

CMSTAT 0A80 CMSIDL — — — — C3EVT C2EVT C1EVT — — — — — C3OUT C2OUT C1OUT 0000

CVRCON 0A82 — — — — — VREFSEL BGSEL<1:0> CVREN CVROE CVRR CVRSS CVR<3:0> 0000

CM1CON 0A84 CON COE CPOL — — — CEVT COUT EVPOL<1:0> — CREF —— CCH<1:0> 0000

CM1MSKSRC 0A86 — — — — SELSRCC<3:0> SELSRCB<3:0> SELSRCA<3:0> 0000

CM1MSKCON 0A88 HLMS — OCEN OCNEN OBEN OBNEN OAEN OANEN NAGS PAGS ACEN ACNEN ABEN ABNEN AAEN AANEN 0000

CM1FLTR 0A8A — — — — — — — — — CFSEL<2:0> CFLTREN CFDIV<2:0> 0000

CM2CON 0A8C CON COE CPOL — — — CEVT COUT EVPOL<1:0> — CREF —— CCH<1:0> 0000

CM2MSKSRC 0A8E — — — — SELSRCC<3:0> SELSRCB<3:0> SELSRCA<3:0> 0000

CM2MSKCON 0A90 HLMS — OCEN OCNEN OBEN OBNEN OAEN OANEN NAGS PAGS ACEN ACNEN ABEN ABNEN AAEN AANEN 0000

CM2FLTR 0A92 — — — — — — — — — CFSEL<2:0> CFLTREN CFDIV<2:0> 0000

CM3CON 0A94 CON COE CPOL — — — CEVT COUT EVPOL<1:0> — CREF —— CCH<1:0> 0000

CM3MSKSRC 0A96 — — — — SELSRCC<3:0> SELSRCB<3:0> SELSRCA<3:0> 0000

CM3MSKCON 0A98 HLMS — OCEN OCNEN OBEN OBNEN OAEN OANEN NAGS PAGS ACEN ACNEN ABEN ABNEN AAEN AANEN 0000

CM3FLTR 0A9A — — — — — — — — — CFSEL<2:0> CFLTREN CFDIV<2:0> 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 111

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-54: DMAC REGISTER MAP

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

DMA0CON 0B00 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0>——MODE<1:0>0000

DMA0REQ 0B02 FORCE — — — — — — — IRQSEL<7:0> 00FF

DMA0STAL 0B04 STA<15:0> 0000

DMA0STAH 0B06 — — — — — — — —STA<23:16>0000

DMA0STBL 0B08 STB<15:0> 0000

DMA0STBH 0B0A — — — — — — — — STB<23:16> 0000

DMA0PAD 0B0C PAD<15:0> 0000

DMA0CNT 0B0E — — CNT<13:0> 0000

DMA1CON 0B10 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0>——MODE<1:0>0000

DMA1REQ 0B12 FORCE — — — — — — — IRQSEL<7:0> 00FF

DMA1STAL 0B14 STA<15:0> 0000

DMA1STAH 0B16 — — — — — — — —STA<23:16>0000

DMA1STBL 0B18 STB<15:0> 0000

DMA1STBH 0B1A — — — — — — — — STB<23:16> 0000

DMA1PAD 0B1C PAD<15:0> 0000

DMA1CNT 0B1E — — CNT<13:0> 0000

DMA2CON 0B20 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0>——MODE<1:0>0000

DMA2REQ 0B22 FORCE — — — — — — — IRQSEL<7:0> 00FF

DMA2STAL 0B24 STA<15:0> 0000

DMA2STAH 0B26 — — — — — — — —STA<23:16>0000

DMA2STBL 0B28 STB<15:0> 0000

DMA2STBH 0B2A — — — — — — — — STB<23:16> 0000

DMA2PAD 0B2C PAD<15:0> 0000

DMA2CNT 0B2E — — CNT<13:0> 0000

DMA2CON 0B30 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0>——MODE<1:0>0000

DMA3REQ 0B32 FORCE — — — — — — — IRQSEL<7:0> 00FF

DMA3STAL 0B34 STA<15:0> 0000

DMA3STAH 0B36 — — — — — — — —STA<23:16>0000

DMA3STBL 0B38 STB<15:0> 0000

DMA3STBH 0B3A — — — — — — — — STB<23:16> 0000

DMA3PAD 0B3C PAD<15:0> 0000

DMA3CNT 0B3E — — CNT<13:0> 0000

DMA4CON 0B40 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0>——MODE<1:0>0000

DMA4REQ 0B42 FORCE — — — — — — — IRQSEL<7:0> 00FF

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 112  2009-2012 Microchip Technology Inc.

DMA4STAL 0B44 STA<15:0> 0000

DMA4STAH 0B46 — — — — — — — —STA<23:16>0000

DMA4STBL 0B48 STB<15:0> 0000

DMA4STBH 0B4A — — — — — — — — STB<23:16> 0000

DMA4PAD 0B4C PAD<15:0> 0000

DMA4CNT 0B4E — — CNT<13:0> 0000

DMA5CON 0B50 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0>——MODE<1:0>0000

DMA5REQ 0B52 FORCE — — — — — — — IRQSEL<7:0> 00FF

DMA5STAL 0B54 STA<15:0> 0000

DMA5STAH 0B56 — — — — — — — —STA<23:16>0000

DMA5STBL 0B58 STB<15:0> 0000

DMA5STBH 0B5A — — — — — — — — STB<23:16> 0000

DMA5PAD 0B5C PAD<15:0> 0000

DMA5CNT 0B5E — — CNT<13:0> 0000

DMA6CON 0B60 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0>——MODE<1:0>0000

DMA6REQ 0B62 FORCE — — — — — — — IRQSEL<7:0> 00FF

DMA6STAL 0B64 STA<15:0> 0000

DMA6STAH 0B66 — — — — — — — —STA<23:16>0000

DMA6STBL 0B68 STB<15:0> 0000

DMA6STBH 0B6A — — — — — — — — STB<23:16> 0000

DMA6PAD 0B6C PAD<15:0> 0000

DMA6CNT 0B6E — — CNT<13:0> 0000

DMA7CON 0B70 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0>——MODE<1:0>0000

DMA7REQ 0B72 FORCE — — — — — — — IRQSEL<7:0> 00FF

DMA7STAL 0B74 STA<15:0> 0000

DMA7STAH 0B76 — — — — — — — —STA<23:16>0000

DMA7STBL 0B78 STB<15:0> 0000

DMA7STBH 0B7A — — — — — — — — STB<23:16> 0000

DMA7PAD 0B7C PAD<15:0> 0000

DMA7CNT 0B7E — — CNT<13:0> 0000

DMA8CON 0B80 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0>——MODE<1:0>0000

DMA8REQ 0B82 FORCE — — — — — — — IRQSEL<7:0> 00FF

DMA8STAL 0B84 STA<15:0> 0000

DMA8STAH 0B86 — — — — — — — —STA<23:16>0000

DMA8STBL 0B88 STB<15:0> 0000

TABLE 4-54: DMAC REGISTER MAP (CONTINUED)

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 113

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DMA8STBH 0B8A — — — — — — — — STB<23:16> 0000

DMA8PAD 0B8C PAD<15:0> 0000

DMA8CNT 0B8E — — CNT<13:0> 0000

DMA9CON 0B90 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0>——MODE<1:0>0000

DMA9REQ 0B92 FORCE — — — — — — — IRQSEL<7:0> 00FF

DMA9STAL 0B94 STA<15:0> 0000

DMA9STAH 0B96 — — — — — — — —STA<23:16>0000

DMA9STBL 0B98 STB<15:0> 0000

DMA9STBH 0B9A — — — — — — — — STB<23:16> 0000

DMA9PAD 0B9C PAD<15:0> 0000

DMA9CNT 0B9E — — CNT<13:0> 0000

DMA10CON 0BA0 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0>——MODE<1:0>0000

DMA10REQ 0BA2 FORCE — — — — — — — IRQSEL<7:0> 00FF

DMA10STAL 0BA4 STA<15:0> 0000

DMA10STAH 0BA6 — — — — — — — —STA<23:16>0000

DMA10STBL 0BA8 STB<15:0> 0000

DMA10STBH 0BAA — — — — — — — — STB<23:16> 0000

DMA10PAD 0BAC PAD<15:0> 0000

DMA10CNT 0BAE — — CNT<13:0> 0000

DMA11CON 0BB0 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0>——MODE<1:0>0000

DM11AREQ 0BB2 FORCE — — — — — — — IRQSEL<7:0> 00FF

DMA11STAL 0BB4 STA<15:0> 0000

DMA11STAH 0BB6 — — — — — — — —STA<23:16>0000

DMA11STBL 0BB8 STB<15:0> 0000

DMA11STBH 0BBA — — — — — — — — STB<23:16> 0000

DMA11PAD 0BBC PAD<15:0> 0000

DMA11CNT 0BBE — — CNT<13:0> 0000

DMA12CON 0BC0 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0>——MODE<1:0>0000

DMA12REQ 0BC2 FORCE — — — — — — — IRQSEL<7:0> 00FF

DMA12STAL 0BC4 STA<15:0> 0000

DMA12STAH 0BC6 — — — — — — — —STA<23:16>0000

DMA12STBL 0BC8 STB<15:0> 0000

DMA12STBH 0BCA — — — — — — — — STB<23:16> 0000

DMA12PAD 0BCC PAD<15:0> 0000

DMA12CNT 0BCE — — CNT<13:0> 0000

TABLE 4-54: DMAC REGISTER MAP (CONTINUED)

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 114  2009-2012 Microchip Technology Inc.

DMA13CON 0BD0 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0>——MODE<1:0>0000

DMA13REQ 0BD2 FORCE — — — — — — — IRQSEL<7:0> 00FF

DMA13STAL 0BD4 STA<15:0> 0000

DMA13STAH 0BD6 — — — — — — — —STA<23:16>0000

DMA13STBL 0BD8 STB<15:0> 0000

DMA13STBH 0BDA — — — — — — — — STB<23:16> 0000

DMA13PAD 0BDC PAD<15:0> 0000

DMA13CNT 0BDE — — CNT<13:0> 0000

DMA14CON 0BE0 CHEN SIZE DIR HALF NULLW — — — — —AMODE<1:0>——MODE<1:0>0000

DMA14REQ 0BE2 FORCE — — — — — — — IRQSEL<7:0> 00FF

DMA14STAL 0BE4 STA<15:0> 0000

DMA14STAH 0BE6 — — — — — — — —STA<23:16>0000

DMA14STBL 0BE8 STB<15:0> 0000

DMA14STBH 0BEA — — — — — — — — STB<23:16> 0000

DMA14PAD 0BEC PAD<15:0> 0000

DMA14CNT 0BEE — — CNT<13:0> 0000

DMAPWC 0BF0 — PWCOL14 PWCOL13 PWCOL12 PWCOL11 PWCOL10 PWCOL9 PWCOL8 PWCOL7 PWCOL6 PWCOL5 PWCOL4 PWCOL3 PWCOL2 PWCOL1 PWCOL0 0000

DMARQC 0BF2 — RQCOL14 RQCOL13 RQCOL12 RQCOL11 RQCOL10 RQCOL9 RQCOL8 RQCOL7 RQCOL6 RQCOL5 RQCOL4 RQCOL3 RQCOL2 RQCOL1 RQCOL0 0000

DMAPPS 0BF4 — PPST14 PPST13 PPST12 PPST11 PPST10 PPST9 PPST8 PPST7 PPST6 PPST5 PPST4 PPST3 PPST2 PPST1 PPST0 0000

DMALCA 0BF6 — — — — — — — — — — — —LSTCH<3:0>000F

DSADRL 0BF8 DSADR<15:0> 0000

DSADRH 0BFA — — — — — — — — DSADR<23:16> 0000

TABLE 4-54: DMAC REGISTER MAP (CONTINUED)

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 115

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-55: PORTA REGISTER MAP FOR dsPIC33EPXXXMU810/814 AND PIC24EPXXXGU810/814 DEVICES ONLY

TABLE 4-56: PORTB REGISTER MAP

TABLE 4-57: PORTC REGISTER MAP FOR dsPIC33EPXXXMU810/814 AND PIC24EPXXXGU810/814 DEVICES ONLY

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISA 0E00 TRISA15 TRISA14 — — — TRISA10 TRISA9 — TRISA7 TRISA6 TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 C6FF

PORTA 0E02 RA15 RA14 — — —RA10RA9— RA7 RA6 RA5 RA4 RA3 RA2 RA1 RA0 xxxx

LATA 0E04 LATA15 LATA14 — — — LATA10 LATA9 — LATA7 LATA6 LATA5 LATA4 LATA3 LATA2 LATA1 LATA0 xxxx

ODCA 0E06 ODCA15 ODCA14 — — — — — — — — ODCA5 ODCA4 ODCA3 ODCA2 ODCA1 ODCA0 0000

CNENA 0E08 CNIEA15 CNIEA14 — — — CNIEA10 CNIEA9 — CNIEA7 CNIEA6 CNIEA5 CNIEA4 CNIEA3 CNIEA2 CNIEA1 CNIEA0 0000

CNPUA 0E0A CNPUA15 CNPUA14 — — — CNPUA10 CNPUA9 — CNPUA7 CNPUA6 CNPUA5 CNPUA4 CNPUA3 CNPUA2 CNPUA1 CNPUA0 0000

CNPDA 0E0C CNPDA15 CNPDA14 — — — CNPDA10 CNPDA9 — CNPDA7 CNPDA6 CNPDA5 CNPDA4 CNPDA3 CNPDA2 CNPDA1 CNPDA0 0000

ANSELA 0E0E — — — — — ANSA10 ANSA9 — ANSA7 ANSA6 — — — — — — 06C0

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISB 0E10 TRISB15 TRISB14 TRISB13 TRISB12 TRISB11 TRISB10 TRISB9 TRISB8 TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 FFFF

PORTB 0E12 RB15 RB14 RB13 RB12 RB11 RB10 RB9 RB8 RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0 xxxx

LATB 0E14 LATB15 LATB14 LATB13 LATB12 LATB11 LATB10 LATB9 LATB8 LATB7 LATB6 LATB5 LATB4 LATB3 LATB2 LATB1 LATB0 xxxx

ODCB 0E16 — — — — — — — — — — — — — — — — 0000

CNENB 0E18 CNIEB15 CNIEB14 CNIEB13 CNIEB12 CNIEB11 CNIEB10 CNIEB9 CNIEB8 CNIEB7 CNIEB6 CNIEB5 CNIEB4 CNIEB3 CNIEB2 CNIEB1 CNIEB0 0000

CNPUB 0E1A CNPUB15 CNPUB14 CNPUB13 CNPUB12 CNPUB11 CNPUB10 CNPUB9 CNPUB8 CNPUB7 CNPUB6 CNPUB5 CNPUB4 CNPUB3 CNPUB2 CNPUB1 CNPUB0 0000

CNPDB 0E1C CNPDB15 CNPDB14 CNPDB13 CNPDB12 CNPDB11 CNPDB10 CNPDB9 CNPDB8 CNPDB7 CNPDB6 CNPDB5 CNPDB4 CNPDB3 CNPDB2 CNPDB1 CNPDB0 0000

ANSELB 0E1E ANSB15 ANSB14 ANSB13 ANSB12 ANSB11 ANSB10 ANSB9 ANSB8 ANSB7 ANSB6 ANSB5 ANSB4 ANSB3 ANSB2 ANSB1 ANSB0 FFFF

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISC 0E20 TRISC15 TRISC14 TRISC13 TRISC12 — — — — — — — TRISC4 TRISC3 TRISC2 TRISC1 —F01E

PORTC 0E22 RC15 RC14 RC13 RC12 — — — — — — — RC4 RC3 RC2 RC1 —xxxx

LATC 0E24 LATC15 LATC14 LATC13 LATC12 — — — — — — — LATC4 LATC3 LATC2 LATC1 —xxxx

ODCC 0E26 — — — — — — — — — — — — — — — — 0000

CNENC 0E28 CNIEC15 CNIEC14 CNIEC13 CNIEC12 — — — — — — — CNIEC4 CNIEC3 CNIEC2 CNIEC1 —0000

CNPUC 0E2A CNPUC15 CNPUC14 CNPUC13 CNPUC12 — — — — — — — CNPUC4 CNPUC3 CNPUC2 CNPUC1 —0000

CNPDC 0E2C CNPDC15 CNPDC14 CNPDC13 CNPDC12 — — — — — — — CNPDC4 CNPDC3 CNPDC2 CNPDC1 —0000

ANSELC 0E2E — ANSC14 ANSC13 — — — — — — — — ANSC4 ANSC3 ANSC2 ANSC1 —601E

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 116  2009-2012 Microchip Technology Inc.

TABLE 4-58: PORTC REGISTER MAP FOR dsPIC33EPXXX(GP/MC/MU)806 AND PIC24EPXXXGP806 DEVICES ONLY

TABLE 4-59: PORTD REGISTER MAP FOR dsPIC33EPXXXMU810/814 AND PIC24EPXXXGU810/814 DEVICES ONLY

TABLE 4-60: PORTD REGISTER MAP FOR dsPIC33EPXXX(GP/MC/MU)806 AND PIC24EPXXXGP806 DEVICES ONLY

File

Name Addr, Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISC 0E20 TRISC15 TRISC14 TRISC13 TRISC12 — — — — — — — — — — — — F000

PORTC 0E22 RC15 RC14 RC13 RC12 — — — — — — — — — — — — xxxx

LATC 0E24 LATC15 LATC14 LATC13 LATC12 — — — — — — — — — — — — xxxx

ODCC 0E26 — — — — — — — — — — — — — — — — 0000

CNENC 0E28 CNIEC15 CNIEC14 CNIEC13 CNIEC12 — — — — — — — — — — — — 0000

CNPUC 0E2A CNPUC15 CNPUC14 CNPUC13 CNPUC12 — — — — — — — — — — — — 0000

CNPDC 0E2C CNPDC15 CNPDC14 CNPDC13 CNPDC12 — — — — — — — — — — — — 0000

ANSELC 0E2E — ANSC14 ANSC13 — — — — — — — — — — — — — 6000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISD 0E30 TRISD15 TRISD14 TRISD13 TRISD12 TRISD11 TRISD10 TRISD9 TRISD8 TRISD7 TRISD6 TRISD5 TRISD4 TRISD3 TRISD2 TRISD1 TRISD0 FFFF

PORTD 0E32 RD15 RD14 RD13 RD12 RD11 RD10 RD9 RD8 RD7 RD6 RD5 RD4 RD3 RD2 RD1 RD0 xxxx

LATD 0E34 LATD15 LATD14 LATD13 LATD12 LATD11 LATD10 LATD9 LATD8 LATD7 LATD6 LATD5 LATD4 LATD3 LATD2 LATD1 LATD0 xxxx

ODCD 0E36 ODCD15 ODCD14 ODCD13 ODCD12 ODCD11 ODCD10 ODCD9 ODCD8 —— ODCD5 ODCD4 ODCD3 ODCD2 ODCD1 ODCD0 0000

CNEND 0E38 CNIED15 CNIED14 CNIED13 CNIED12 CNIED11 CNIED10 CNIED9 CNIED8 CNIED7 CNIED6 CNIED5 CNIED4 CNIED3 CNIED2 CNIED1 CNIED0 0000

CNPUD 0E3A CNPUD15 CNPUD14 CNPUD13 CNPUD12 CNPUD11 CNPUD10 CNPUD9 CNPUD8 CNPUD7 CNPUD6 CNPUD5 CNPUD4 CNPUD3 CNPUD2 CNPUD1 CNPUD0 0000

CNPDD 0E3C CNPDD15 CNPDD14 CNPDD13 CNPDD12 CNPDD11 CNPDD10 CNPDD9 CNPDD8 CNPDD7 CNPDD6 CNPDD5 CNPDD4 CNPDD3 CNPDD2 CNPDD1 CNPDD0 0000

ANSELD 0E3E ———————— ANSD7 ANSD6 — — — — — — 00C0

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISD 0E30 ———— TRISD11 TRISD10 TRISD9 TRISD8 TRISD7 TRISD6 TRISD5 TRISD4 TRISD3 TRISD2 TRISD1 TRISD0 0FFF

PORTD 0E32 ———— RD11 RD10 RD9 RD8 RD7 RD6 RD5 RD4 RD3 RD2 RD1 RD0 xxxx

LATD 0E34 ———— LATD11 LATD10 LATD9 LATD8 LATD7 LATD6 LATD5 LATD4 LATD3 LATD2 LATD1 LATD0 xxxx

ODCD 0E36 ———— ODCD11 ODCD10 ODCD9 ODCD8 —— ODCD5 ODCD4 ODCD3 ODCD2 ODCD1 ODCD0 0000

CNEND 0E38 ———— CNIED11 CNIED10 CNIED9 CNIED8 CNIED7 CNIED6 CNIED5 CNIED4 CNIED3 CNIED2 CNIED1 CNIED0 0000

CNPUD 0E3A ———— CNPUD11 CNPUD10 CNPUD9 CNPUD8 CNPUD7 CNPUD6 CNPUD5 CNPUD4 CNPUD3 CNPUD2 CNPUD1 CNPUD0 0000

CNPDD 0E3C ———— CNPDD11 CNPDD10 CNPDD9 CNPDD8 CNPDD7 CNPDD6 CNPDD5 CNPDD4 CNPDD3 CNPDD2 CNPDD1 CNPDD0 0000

ANSELD 0E3E ———————— ANSD7 ANSD6 — — — — — — 00C0

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 117

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-61: PORTE REGISTER MAP FOR dsPIC33EPXXXMU810/814 AND PIC24EPXXXGU810/814 DEVICES ONLY

TABLE 4-62: PORTE REGISTER MAP FOR dsPIC33EPXXX(GP/MC/MU)806 AND PIC24EPXXXGP806 DEVICES ONLY

TABLE 4-63: PORTF REGISTER MAP FOR dsPIC33EPXXXMU810/814 AND PIC24EPXXXGU810/814 DEVICES ONLY

File

Name Addr.Bit 15Bit 14Bit 13Bit 12Bit 11Bit 10Bit 9Bit 8Bit 7Bit 6Bit 5Bit 4Bit 3Bit 2Bit 1Bit 0All

Resets

TRISE 0E40 — — — — — — TRISE9 TRISE8 TRISE7 TRISE6 TRISE5 TRISE4 TRISE3 TRISE2 TRISE1 TRISE0 03FF

PORTE 0E42 — — — — — — RE9 RE8 RE7 RE6 RE5 RE4 RE3 RE2 RE1 RE0 xxxx

LATE 0E44 — — — — — — LATE9 LATE8 LATE7 LATE6 LATE5 LATE4 LATE3 LATE2 LATE1 LATE0 xxxx

ODCE 0E46 — — — — — — — — — — — — — — — — 0000

CNENE 0E48 — — — — — — CNIEE9 CNIEE8 CNIEE7 CNIEE6 CNIEE5 CNIEE4 CNIEE3 CNIEE2 CNIEE1 CNIEE0 0000

CNPUE 0E4A — — — — — — CNPUE9 CNPUE8 CNPUE7 CNPUE6 CNPUE5 CNPUE4 CNPUE3 CNPUE2 CNPUE1 CNPUE0 0000

CNPDE 0E4C — — — — — — CNPDE9 CNPDE8 CNPDE7 CNPDE6 CNPDE5 CNPDE4 CNPDE3 CNPDE2 CNPDE1 CNPDE0 0000

ANSELE 0E4E — — — — — — ANSE9 ANSE8 ANSE7 ANSE6 ANSE5 ANSE4 ANSE3 ANSE2 ANSE1 ANSE0 03FF

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISE 0E40 — — — — — — — — TRISE7 TRISE6 TRISE5 TRISE4 TRISE3 TRISE2 TRISE1 TRISE0 00FF

PORTE 0E42 — — — — — — — — RE7 RE6 RE5 RE4 RE3 RE2 RE1 RE0 xxxx

LATE 0E44 — — — — — — — — LATE7LATE6LATE5LATE4LATE3LATE2LATE1LATE0xxxx

ODCE 0E46 — — — — — — — — — — — — — — — — 0000

CNENE 0E48 — — — — — — — — CNIEE7 CNIEE6 CNIEE5 CNIEE4 CNIEE3 CNIEE2 CNIEE1 CNIEE0 0000

CNPUE 0E4A — — — — — — — — CNPUE7 CNPUE6 CNPUE5 CNPUE4 CNPUE3 CNPUE2 CNPUE1 CNPUE0 0000

CNPDE 0E4C — — — — — — — — CNPDE7 CNPDE6 CNPDE5 CNPDE4 CNPDE3 CNPDE2 CNPDE1 CNPDE0 0000

ANSELE 0E4E — — — — — — — — ANSE7 ANSE6 ANSE5 ANSE4 ANSE3 ANSE2 ANSE1 ANSE0 00FF

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISF 0E50 —— TRISF13 TRISF12 — — —TRISF8 —— TRISF5 TRISF4 TRISF3 TRISF2 TRISF1 TRISF0 313F

PORTF 0E52 —— RF13 RF12 — — —RF8 —— RF5 RF4 RF3 RF2 RF1 RF0 xxxx

LATF 0E54 —— LATF13 LATF12 — — — LATF8 —— LATF5 LATF4 LATF3 LATF2 LATF1 LATF0 xxxx

ODCF 0E56 —— ODCF13 ODCF12 — — —ODCF8 —— ODCF5 ODCF4 ODCF3 ODCF2 ODCF1 ODCF0 0000

CNENF 0E58 —— CNIEF13 CNIEF12 — — — CNIEF8 —— CNIEF5 CNIEF4 CNIEF3 CNIEF2 CNIEF1 CNIEF0 0000

CNPUF 0E5A —— CNPUF13 CNPUF12 — — — CNPUF8 —— CNPUF5 CNPUF4 CNPUF3 CNPUF2 CNPUF1 CNPUF0 0000

CNPDF 0E5C —— CNPDF13 CNPDF12 — — — CNPDF8 —— CNPDF5 CNPDF4 CNPDF3 CNPDF2 CNPDF1 CNPDF0 0000

ANSELF 0E5E — — — — — — — — — — — — — — — — 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 118  2009-2012 Microchip Technology Inc.

TABLE 4-64: PORTF REGISTER MAP FOR dsPIC33EPXXX(GP/MC)806 AND PIC24EPXXXGP806 DEVICES ONLY

TABLE 4-65: PORTF REGISTER MAP FOR dsPIC33EPXXXMU806 DEVICES ONLY

TABLE 4-66: PORTG REGISTER MAP FOR dsPIC33EPXXXMU810/814 AND PIC24EPXXXGU810/814 DEVICES ONLY

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISF 0E50 — — — — — — — — — TRISG6 TRISF5 TRISF4 TRISF3TRISF2TRISF1TRISF0 003B

PORTF 0E52 — — — — — — — — — RG6 RF5 RF4 RF3 RF2 RF1 RF0 xxxx

LATF 0E54 — — — — — — — — — LATG6 LATF5 LATF4 LATF3 LATF2 LATF1 LATF0 xxxx

ODCF 0E56 — — — — — — — — — ODCF6 ODCF5 ODCF4 ODCF3 ODCF2 ODCF1 ODCF0 0000

CNENF 0E58 — — — — — — — — — CNIEG6 CNIEF5 CNIEF4 CNIEF3 CNIEF2 CNIEF1 CNIEF0 0000

CNPUF 0E5A — — — — — — — — — CNPUG6 CNPUF5 CNPUF4 CNPUF3 CNPUF2 CNPUF1 CNPUF0 0000

CNPDF 0E5C — — — — — — — — — CNPDG6 CNPDF5 CNPDF4 CNPDF3 CNPDF2 CNPDF1 CNPDF0 0000

ANSELF 0E5E — — — — — — — — — — — — — — — — 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISF 0E50 — — — — — — — — — — TRISF5 TRISF4 TRISF3 — TRISF1 TRISF0 003B

PORTF 0E52 — — — — — — — — — —RF5RF4RF3—RF1RF0xxxx

LATF 0E54 — — — — — — — — — — LATF5 LATF4 LATF3 — LATF1 LATF0 xxxx

ODCF 0E56 — — — — — — — — — — ODCF5 ODCF4 ODCF3 — ODCF1 ODCF0 0000

CNENF 0E58 — — — — — — — — — — CNIEF5 CNIEF4 CNIEF3 — CNIEF1 CNIEF0 0000

CNPUF 0E5A — — — — — — — — — — CNPUF5 CNPUF4 CNPUF3 — CNPUF1 CNPUF0 0000

CNPDF 0E5C — — — — — — — — — — CNPDF5 CNPDF4 CNPDF3 — CNPDF1 CNPDF0 0000

ANSELF 0E5E — — — — — — — — — — — — — — — — 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISG 0E60 TRISG15 TRISG14 TRISG13 TRISG12 —— TRISG9 TRISG8 TRISG7 TRISG6 — — — — TRISG1 TRISG0 F3C3

PORTG 0E62 RG15 RG14 RG13 RG12 —— RG9 RG8 RG7 RG6 ——RG3

(1)RG2(1)RG1 RG0 xxxx

LATG 0E64 LATG15 LATG14 LATG13 LATG12 —— LATG9 LATG8 LATG7 LATG6 — — — —LATG1LATG0xxxx

ODCG 0E66 ODCG15 ODCG14 ODCG13 ODCG12 — — — — — — — — — — ODCG1 ODCG0 0000

CNENG 0E68 CNIEG15 CNIEG14 CNIEG13 CNIEG12 —— CNIEG9 CNIEG8 CNIEG7 CNIEG6 ——CNIEG3

(1)CNIEG2(1)CNIEG1 CNIEG0 0000

CNPUG 0E6A CNPUG15 CNPUG14 CNPUG13 CNPUG12 —— CNPUG9 CNPUG8 CNPUG7 CNPUG6 — — — — CNPUG1 CNPUG0 0000

CNPDG 0E6C CNPDG15 CNPDG14 CNPDG13 CNPDG12 —— CNPDG9 CNPDG8 CNPDG7 CNPDG6 — — — — CNPDG1 CNPDG0 0000

ANSELG 0E6E — — — — — — ANSG9 ANSG8 ANSG7 ANSG6 — — — — — — 03C0

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

Note 1: If RG2 and RG3 are used as general purpose inputs, the VUSB3V3 pin must be connected to VDD.

 2009-2012 Microchip Technology Inc. DS70616G-page 119

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-67: PORTG REGISTER MAP FOR dsPIC33EPXXX(GP/MC)806 AND PIC24EPXXXGP806 DEVICES ONLY

TABLE 4-68: PORTG REGISTER MAP FOR dsPIC33EPXXXMU806 DEVICES ONLY

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISG 0E60 — — — — — — TRISG9 TRISG8 TRISG7 TRISG6 —— TRISG3 TRISG2 — — 03C0

PORTG 0E62 — — — — — — RG9 RG8 RG7 RG6 ——RG3

(1)RG2(1)— — xxxx

LATG 0E64 — — — — — — LATG9 LATG8 LATG7 LATG6 ——LATG3LATG2 — — xxxx

ODCG 0E66 — — — — — — — — — — — — ODCG3 ODCG2 — — 0000

CNENG 0E68 — — — — — — CNIEG9 CNIEG8 CNIEG7 CNIEG6 —— CNIEG3(1)CNIEG2(1)— — 0000

CNPUG 0E6A — — — — — — CNPUG9 CNPUG8 CNPUG7 CNPUG6 —— CNPUG3 CNPUG2 — — 0000

CNPDG 0E6C — — — — — — CNPDG9 CNPDG8 CNPDG7 CNPDG6 —— CNPDG3 CNPDG2 — — 0000

ANSELG 0E6E — — — — — — ANSG9 ANSG8 ANSG7 ANSG6 — — — — — — 03C0

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

Note 1: If RG2 and RG3 are used as general purpose inputs, the VUSB3V3 pin must be connected to VDD.

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISG 0E60 — — — — — — TRISG9 TRISG8 TRISG7 TRISG6 — — — — — — 03C0

PORTG 0E62 — — — — — — RG9 RG8 RG7 RG6 ——RG3

(1)RG2(1)— — xxxx

LATG 0E64 — — — — — — LATG9 LATG8 LATG7 LATG6 — — — — — — xxxx

ODCG 0E66 — — — — — — — — — — — — — — — — 0000

CNENG 0E68 — — — — — — CNIEG9 CNIEG8 CNIEG7 CNIEG6 —— CNIEG3(1)CNIEG2(1)— — 0000

CNPUG 0E6A — — — — — — CNPUG9 CNPUG8 CNPUG7 CNPUG6 — — — — — — 0000

CNPDG 0E6C — — — — — — CNPDG9 CNPDG8 CNPDG7 CNPDG6 — — — — — — 0000

ANSELG 0E6E — — — — — — ANSG9 ANSG8 ANSG7 ANSG6 — — — — — — 03C0

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

Note 1: If RG2 and RG3 are used as general purpose inputs, the VUSB3V3 pin must be connected to VDD.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 120  2009-2012 Microchip Technology Inc.

TABLE 4-69: PORTH REGISTER MAP FOR dsPIC33EPXXXMU814 AND PIC24EPXXXGU814 DEVICES ONLY

TABLE 4-70: PORTJ REGISTER MAP FOR dsPIC33EPXXXMU814 AND PIC24EPXXXGU814 DEVICES ONLY

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISH 0E70 TRISH15 TRISH14 TRISH13 TRISH12 TRISH11 TRISH10 TRISH9 TRISH8 TRISH7 TRISH6 TRISH5 TRISH4 TRISH3 TRISH2 TRISH1 TRISH0 FFFF

PORTH 0E72 RH15 RH14 RH13 RH12 RH11 RH10 RH9 RH8 RH7 RH6 RH5 RH4 RH3 RH2 RH1 RH0 xxxx

LATH 0E74 LATH15 LATH14 LATH13 LATH12 LATH11 LATH10 LATH9 LATH8 LATH7 LATH6 LATH5 LATH4 LATH3 LATH2 LATH1 LATH0 xxxx

ODCH 0E76 ODCH15 ODCH14 ODCH13 ODCH12 ODCH11 ODCH10 ODCH9 ODCH8 ODCH7 ODCH6 ODCH5 ODCH4 ODCH3 ODCH2 ODCH1 ODCH0 0000

CNENH 0E78 CNIEH15 CNIEH14 CNIEH13 CNIEH12 CNIEH11 CNIEH10 CNIEH9 CNIEH8 CNIEH7 CNIEH6 CNIEH5 CNIEH4 CNIEH3 CNIEH2 CNIEH1 CNIEH0 0000

CNPUH 0E7A CNPUH15 CNPUH14 CNPUH13 CNPUH12 CNPUH11 CNPUH10 CNPUH9 CNPUH8 CNPUH7 CNPUH6 CNPUH5 CNPUH4 CNPUH3 CNPUH2 CNPUH1 CNPUH0 0000

CNPDH 0E7C CNPDH15 CNPDH14 CNPDH13 CNPDH12 CNPDH11 CNPDH10 CNPDH9 CNPDH8 CNPDH7 CNPDH6 CNPDH5 CNPDH4 CNPDH3 CNPDH2 CNPDH1 CNPDH0 0000

ANSELH 0E7E — — — — — — — — — — — — — — — — 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISJ 0E80 TRISJ15 TRISJ14 TRISJ13 TRISJ12 TRISJ11 TRISJ10 TRISJ9TRISJ8TRISJ7TRISJ6TRISJ5TRISJ4TRISJ3TRISJ2TRISJ1TRISJ0 FFFF

PORTJ 0E82 RJ15 RJ14 RJ13 RJ12 RJ12 RJ10 RJ9 RJ8 RJ7 RJ6 RJ5 RJ4 RJ3 RJ2 RJ1 RJ0 xxxx

LATJ 0E84 LATJ15 LATJ14 LATJ13 LATJ12 LATJ11 LATJ10 LATJ9 LATJ8 LATJ7 LATJ6 LATJ5 LATJ4 LATJ3 LATJ2 LATJ1 LATJ0 xxxx

ODCJ 0E86 ODCJ15 ODCJ14 ODCJ13 ODCJ12 ODCJ11 ODCJ10 ODCJ9 ODCJ8 ODCJ7 ODCJ6 ODCJ5 ODCJ4 ODCJ3 ODCJ2 ODCJ1 ODCJ0 0000

CNENJ 0E88 CNIEJ15 CNIEJ14 CNIEJ13 CNIEJ12 CNIEJ11 CNIEJ10 CNIEJ9 CNIEJ8 CNIEJ7 CNIEJ6 CNIEJ5 CNIEJ4 CNIEJ3 CNIEJ2 CNIEJ1 CNIEJ0 0000

CNPUJ 0E8A CNPUJ15 CNPUJ14 CNPUJ13 CNPUJ12 CNPUJ11 CNPUJ10 CNPUJ9 CNPUJ8 CNPUJ7 CNPUJ6 CNPUJ5 CNPUJ4 CNPUJ3 CNPUJ2 CNPUJ1 CNPUJ0 0000

CNPDJ 0E8C CNPDJ15 CNPDJ14 CNPDJ13 CNPDJ12 CNPDJ11 CNPDJ10 CNPDJ9 CNPDJ8 CNPDJ7 CNPDJ6 CNPDJ5 CNPDJ4 CNPDJ3 CNPDJ2 CNPDJ1 CNPDJ0 0000

ANSELJ 0E8E — — — — — — — — — — — — — — — — 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

 2009-2012 Microchip Technology Inc. DS70616G-page 121

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-71: PORTK REGISTER MAP FOR dsPIC33EPXXXMU814 AND PIC24EPXXXGU814 DEVICES ONLY

TABLE 4-72: PAD CONFIGURATION REGISTER MAP

File

Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

TRISK 0E90 TRISK15 TRISK14 TRISK13 TRISK12 TRISK11 ————————— TRISK1 TRISK0 F803

PORTK 0E92 RK15 RK14 RK13 RK12 RK11 —————————RK1RK0xxxx

LATK 0E94 LATK15 LATK14 LATK13 LATK12 LATK11 —————————LATK1LATK0xxxx

ODCK 0E96 ODCK15 ODCK14 ODCK13 ODCK12 ODCK11 ————————— ODCK1 ODCK0 0000

CNENK 0E98 CNIEK15 CNIEK14 CNIEK13 CNIEK12 CNIEK11 ————————— CNIEK1 CNIEK0 0000

CNPUK 0E9A CNPUK15 CNPUK14 CNPUK13 CNPUK12 CNPUK11 ————————— CNPUK1 CNPUK0 0000

CNPDK 0E9C CNPDK15 CNPDK14 CNPDK13 CNPDK12 CNPDK11 ————————— CNPDK1 CNPDK0 0000

ANSELK 0E9E — — — — — — — — — — — — — — — — 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All

Resets

PADCFG1 0EFE — — — — — — — — — — — — — — RTSECSEL PMPTTL 0000

Legend: x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 122  2009-2012 Microchip Technology Inc.

4.4.1 PAGED MEMORY SCHEME

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 architecture extends

the available data space through a paging scheme,

which allows the available data space to be accessed

using MOV instructions in a linear fashion for pre- and

post-modified Effective Addresses (EA). The upper half

of Base Data Space address is used in conjunction with

the Data Space Page registers, the 10-Bit Read Page

(DSWPAG), to form an Extended Data Space (EDS)

address or Program Space Visibility (PSV) address.

The Data Space Page registers are located in the SFR

space.

Construction of the EDS address is shown in Figure 4-1.

When DSRPAG<9> = 0 and the base address bit,

EA<15> = 1, DSRPAG<8:0> is concatenated onto

EA<14:0> to form the 24-bit EDS read address.

Similarly, when the base address bit, EA<15> = 1,

DSWPAG<8:0> is concatenated onto EA<14:0> to form

the 24-bit EDS write address.

EXAMPLE 4-1: EXTENDED DATA SPACE (EDS) READ ADDRESS GENERATION

DSRPAG<8:0>

9 Bits

15 Bits

Select

Byte

24-Bit EDS EA Select

(DSRPAG = Don't Care) No EDS Access

Select

16-Bit DS EA Byte

EA<15> = 0

DSRPAG

EA<15>

Note: DS read access when DSRPAG = 0x000 will force an address error trap.

DSRPAG<9>

Generate

PSV Address

 2009-2012 Microchip Technology Inc. DS70616G-page 123

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

EXAMPLE 4-2: EXTENDED DATA SPACE (EDS) WRITE ADDRESS GENERATION

The paged memory scheme provides access to

multiple 32-Kbyte windows in the EDS and PSV

memory. The Data Space Page registers DSxPAG, in

combination with the upper half of data space address

can provide up to 16 Mbytes of additional address

space in the EDS and 12 Mbytes (DSRPAG only) of

PSV address space. The paged data memory space is

shown in Example 4-3.

The Program Space (PS) can be accessed with

DSRPAG of 0x200 or greater. Only reads from PS are

supported using the DSRPAG. Writes to PS are not

supported, so DSWPAG is dedicated to DS, including

EDS, only. The data space and EDS can be read from

and written to using DSRPAG and DSWPAG,

respectively.

DSWPAG<8:0>

9 Bits

15 Bits

Byte

24-Bit EDS EA Select

(DSWPAG = Don’t Care)

No EDS Access

Select

16-Bit DS EA Byte

EA<15> = 0

Note: DS read access when DSRPAG = 0x000 will force an address error trap.

Generate

PSV Address

EA<15>

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 124  2009-2012 Microchip Technology Inc.

EXAMPLE 4-3: PAGED DATA MEMORY SPACE

0x0000

Program Memory

0x0000

0x7FFF

EDS Page 0x001

0x0000

SFR Registers

0x0FFF

0x1000

Up to 28 Kbytes

0x7FFF

Local Data Space EDS

(DSRPAG<9:0>/DSWPAG<8:0>)

Reserved

(Will produce an

address error trap)

32 Kbytes

EDS Window

0xFFFF

0x8000

Page 0

Program Space

0x00_0000

0x7F_FFFF

(lsw – <15:0>)

0x0000

(DSRPAG = 0x001)

(DSWPAG = 0x001)

EDS Page 0x1FF

(DSRPAG = 0x1FF)

(DSWPAG = 0x1FF)

EDS Page 0x200

(DSRPAG = 0x200)

PSV

Program

Memory

EDS Page 0x2FF

(DSRPAG = 0x2FF)

EDS Page 0x300

(DSRPAG = 0x300)

EDS Page 0x3FF

(DSRPAG = 0x3FF)

0x0000

0x7FFF

0x0000

0x7FFF

0x0000

0x7FFF

DS_Addr<14:0>

DS_Addr<15:0>

(lsw)

PSV

Program

Memory

(MSB)

Table Address Space

(TBLPAG<7:0>)

Program Memory

0x00_0000

0x7F_FFFF

(MSB – <23:16>)

(TBLPAG = 0x00)

0xFFFF

DS_Addr<15:0>

lsw using

TBLRDL/TBLWTL

MSB using

TBLRDH/TBLWTH

0x0000 (TBLPAG = 0x7F)

0xFFFF

lsw using

TBLRDL/TBLWTL

MSB using

TBLRDH/TBLWTH

(Instruction and Data)

No Writes Allowed

RAM

0x0000

0x7FFF

0x0000

 2009-2012 Microchip Technology Inc. DS70616G-page 125

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Allocating different Page registers for read and write

access allows the architecture to support data

movement between different pages in data memory.

This is accomplished by setting the DSRPAG register

value to the page from which you want to read and

configuring the DSWPAG register to the page to which

it needs to be written. Data can also be moved from

different PSV to EDS pages, by configuring the

DSRPAG and DSWPAG registers to address PSV and

EDS space, respectively. The data can be moved

between pages by a single instruction.

When an EDS or PSV page overflow or underflow

occurs, EA<15> is cleared as a result of the register

indirect EA calculation. An overflow or underflow of the

EA in the EDS or PSV pages can occur at the page

boundaries when:

• The initial address, prior to modification,

addresses an EDS or PSV page.

• The EA calculation uses Pre- or Post-Modified

not include Register Offset Addressing.

In general, when an overflow is detected, the DSxPAG

keep the base address within the EDS or PSV window.

When an underflow is detected, the DSxPAG register is

decremented and the EA<15> bit is set to keep the

base address within the EDS or PSV window. This

creates a linear EDS and PSV address space, but only

when using Register Indirect Addressing modes.

Exceptions to the operation described above arise

when entering and exiting the boundaries of Page 0,

EDS and PSV spaces. Table 4 - 7 3 lists the effects of

overflow and underflow scenarios at different

boundaries.

In the following cases, when overflow or underflow

occurs, the EA<15> bit is set and the DSxPAG is not

modified; therefore, the EA will wrap to the beginning of

the current page:

• Register Indirect with Register Offset Addressing

• Modulo Addressing

• Bit-Reversed Addressing

TABLE 4-73: OVERFLOW AND UNDERFLOW SCENARIOS AT PAGE 0, EDS and

PSV SPACE BOUNDARIES(2,3,4)

O/U,

R/W Operation

Before After

DSxPAG DS

EA<15>

Page

Description DSxPAG DS

EA<15>

Page

Description

Read

[++Wn]

[Wn++]

DSRPAG = 0x1FF 1EDS: Last page DSRPAG = 0x1FF 0See Note 1

Read

DSRPAG = 0x2FF 1PSV: Last lsw

page

DSRPAG = 0x300 1PSV: First MSB

page

Read

DSRPAG = 0x3FF 1PSV: Last MSB

page

DSRPAG = 0x3FF 0See Note 1

Write

DSWPAG = 0x1FF 1EDS: Last page DSWPAG = 0x1FF 0See Note 1

Read

[--Wn]

[Wn--]

DSRPAG = 0x001 1EDS page DSRPAG = 0x001 0See Note 1

Read

DSRPAG = 0x200 1PSV: First lsw

page

DSRPAG = 0x200 0See Note 1

Read

DSRPAG = 0x300 1PSV: First MSB

page

DSRPAG = 0x2FF 1PSV: Last lsw

page

Legend: O = Overflow, U = Underflow, R = Read, W = Write

Note 1: Register Indirect Addressing now addresses a location in the Base Data Space (0x0000-0x8000).

2: An EDS access with DSxPAG = 0x000 will generate an address error trap.

3: Only reads from PS are supported using DSRPAG. An attempt to write to PS using DSWPAG will generate

an address error trap.

4: Pseudo-Linear Addressing is not supported for large offsets.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 126  2009-2012 Microchip Technology Inc.

4.4.2 EXTENDED X DATA SPACE

The lower half of the base address space range, between

0x0000 and 0x7FFF, is always accessible regardless of

the contents of the Data Space Page registers. It is

indirectly addressable through the register indirect

instructions. It can be regarded as being located in the

default EDS Page 0 (i.e., EDS address range of

0x000000 to 0x007FFF with the base address bit,

EA<15> = 0, for this address range). However, Page 0

cannot be accessed through the upper 32 Kbytes

(0x8000 to 0xFFFF) of Base Data Space, in combination

with DSRPAG = 0x00 or DSWPAG = 0x00.

Consequently, DSRPAG and DSWPAG are initialized to

0x001 at Reset.

The remaining pages including both EDS and PSV

pages are only accessible using the DSRPAG or

DSWPAG registers in combination with the upper

32 Kbytes, 0x8000 to 0xFFFF, of the base address,

where base address bit, EA<15> = 1.

For example, when DSRPAG = 0x01 or

DSWPAG = 0x01, accesses to the upper 32 Kbytes,

0x8000 to 0xFFFF, of the data space will map to the

EDS address range of 0x008000 to 0x00FFFF.

When DSRPAG = 0x02 or DSWPAG = 0x02,

accesses to the upper 32 Kbytes of the data space

will map to the EDS address range of 0x010000 to

0x017FFF and so on, as shown in the EDS memory

map in Figure 4-7.

For more information of the PSV page access using

Data Space Page registers refer to Section 4.5

“Program Space Visibility from Data Space” in

Section 4. “Program Memory” (DS70613) of the

“dsPIC33E/PIC24E Family Reference Manual”.

FIGURE 4-7: EDS MEMORY MAP

Note 1: DSxPAG should not be used to access

Page 0. An EDS access with DSxPAG

set to 0x000 will generate an address

error trap.

2: Clearing DSxPAG in software has no

effect.

0x008000

0x010000

0x018000

0xFE8000

0xFF0000

0xFF8000

SFR/DS

0x0000

0xFFFF

EDS EA Address (24 bits)

Conventional

EA<15:0>

0x8000

(PAGE 0)

(DSWPAG<8:0>, EA<14:0>)

DSRPAG<9> = 0

DS Address

Page 1FD

Page 1FE

Page 1FF

Page 1

Page 2

Page 3

(DSRPAG<8:0>, EA<14:0>)

 2009-2012 Microchip Technology Inc. DS70616G-page 127

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

4.4.3 EDS ARBITRATION AND BUS

MASTER PRIORITY

EDS accesses from bus masters in the system are

arbitrated.

The arbiter for data memory (including EDS) arbitrates

between the CPU, the DMA, the USB module and the

ICD module. In the event of coincidental access to a

bus by the bus masters, the arbiter determines which

bus master access has the highest priority. The other

bus masters are suspended and processed after the

access of the bus by the bus master with the highest

priority.

By default, the CPU is Bus Master 0 (M0) with the

highest priority and the ICD is Bus Master 4 (M4) with

the lowest priority. The remaining bus masters (USB

and DMA Controllers) are allocated to M2 and M3,

respectively (M1 is reserved and cannot be used). The

user application may raise or lower the priority of the

masters to be above that of the CPU by setting the

appropriate bits in the EDS Bus Master Priority Control

(MSTRPR) register. All bus masters with raised

priorities will maintain the same priority relationship

relative to each other (i.e., M1 being highest and M3

being lowest, with M2 in between). Also, all the bus

masters with priorities below that of the CPU maintain

the same priority relationship relative to each other.

The priority schemes for bus masters with different

MSTRPR values are tabulated in Table 4-74.

This bus master priority control allows the user

application to manipulate the real-time response of the

system, either statically during initialization, or

dynamically in response to real-time events.

TABLE 4-74: EDS BUS ARBITER PRIORITY

FIGURE 4-8: EDS ARBITER ARCHITECTURE

Priority

MSTRPR<15:0> Bit Setting(1)

0x0000 0x0008 0x0020 0x0028

M0 (highest) CPU USB DMA USB

M1 Reserved CPU CPU DMA

M2 USB Reserved Reserved CPU

M3 DMA DMA USB Reserved

M4 (lowest) ICD ICD ICD ICD

Note 1: All other values of MSTRPR<15:0> are reserved.

DPSRAM ICD

USB

EDS Arbiter

M0 M1 M2 M3 M4

Reserved

MSTRPR<15:0>

DMA CPU

SRAM

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 128  2009-2012 Microchip Technology Inc.

4.4.4 SOFTWARE STACK

The W15 register serves as a dedicated software Stack

Pointer (SP) and is automatically modified by exception

processing, subroutine calls and returns; however,

W15 can be referenced by any instruction in the same

manner as all other W registers. This simplifies

reading, writing and manipulating of the Stack Pointer

(for example, creating stack frames).

W15 is initialized to 0x1000 during all Resets. This

address ensures that the SP points to valid RAM in

all dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices and permits

stack availability for non-maskable trap exceptions.

These can occur before the SP is initialized by the user

software. You can reprogram the SP during

initialization to any location within data space.

The Stack Pointer always points to the first available

free word and fills the software stack working from

lower toward higher addresses. Figure 4-9 illustrates

how it pre-decrements for a stack pop (read) and

post-increments for a stack push (writes).

When the PC is pushed onto the stack, PC<15:0> is

pushed onto the first available stack word, then

PC<22:16> is pushed into the second available stack

location. For a PC push during any CALL instruction,

the MSB of the PC is zero-extended before the push,

as shown in Figure 4-9. During exception processing,

the MSB of the PC is concatenated with the lower 8 bits

of the CPU STATUS Register, SR. This allows the

contents of SRL to be preserved automatically during

interrupt processing.

FIGURE 4-9: CALL STACK FRAME

4.5 Instruction Addressing Modes

The addressing modes, shown in Table 4-75, form the

basis of the addressing modes optimized to support the

specific features of individual instructions. The

addressing modes provided in the MAC class of

instructions differ from those in the other instruction

types.

4.5.1 FILE REGISTER INSTRUCTIONS

Most file register instructions use a 13-bit address field

(f) to directly address data present in the first

8192 bytes of data memory (Near Data Space). Most

file register instructions employ a working register, W0,

which is denoted as WREG in these instructions. The

destination is typically either the same file register or

WREG (with the exception of the MUL instruction),

which writes the result to a register or register pair. The

MOV instruction allows additional flexibility and can

access the entire data space.

4.5.2 MCU INSTRUCTIONS

The three-operand MCU instructions are of the form:

Operand 3 = Operand 1 <function> Operand 2

where Operand 1 is always a working register (that is,

the addressing mode can only be Register Direct),

which is referred to as Wb. Operand 2 can be a W reg-

ister, fetched from data memory, or a 5-bit literal. The

result location can be either a W register or a data

memory location. The following addressing modes are

supported by MCU instructions:

• Register Direct

• Register Indirect

• Register Indirect Post-Modified

• Register Indirect Pre-Modified

• 5-bit or 10-bit Literal

Note: To protect against misaligned stack

accesses, W15<0> is fixed to ‘0’ by the

hardware.

Note 1: For main system Stack Pointer (W15)

coherency, W15 is never subject to

(EDS) paging and is therefore,

restricted to the address range of

0x0000 to 0xFFFF. The same applies to

W14 when used as a Stack Frame

Pointer (SFA = 1).

2: As the stack can be placed in and

across X, Y and DMA RAM spaces,

care must be exercised regarding its

use, particularly with regard to local

automatic variables in a C development

environment.

Note: Not all instructions support all of the

addressing modes given above. Individ-

ual instructions can support different

subsets of these addressing modes.

PC<15:1>

b‘000000000’

015

W15 (before CALL)

W15 (after CALL)

Stack Grows Toward

Higher Address

0x0000

PC<22:16>

CALL SUBR

 2009-2012 Microchip Technology Inc. DS70616G-page 129

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 4-75: FUNDAMENTAL ADDRESSING MODES SUPPORTED

4.5.3 MOVE AND ACCUMULATOR

INSTRUCTIONS

Move instructions (dsPIC33EPXXXMU806/810/814

and PIC24EPXXXGU810/814) and the DSP accumula-

tor class of instructions (dsPIC33EPXXXMU806/810/

814 only) provide a greater degree of addressing

flexibility than other instructions. In addition to the

addressing modes supported by most MCU

instructions, move and accumulator instructions also

support Register Indirect with Register Offset

Addressing mode, also referred to as Register Indexed

mode.

In summary, the following addressing modes are

supported by move and accumulator instructions:

• Register Direct

• Register Indirect

• Register Indirect Post-modified

• Register Indirect Pre-modified

• Register Indirect with Register Offset (Indexed)

• Register Indirect with Literal Offset

• 8-Bit Literal

• 16-Bit Literal

4.5.4 MAC INSTRUCTIONS

(dsPIC33EPXXXMU806/810/814

DEVICES ONLY)

The dual source operand DSP instructions (CLR, ED,

EDAC, MAC, MPY, MPY.N, MOVSAC and MSC), also referred

to as MAC instructions, use a simplified set of addressing

modes to allow the user application to effectively

manipulate the Data Pointers through register indirect

tables.

The two-source operand prefetch registers must be

members of the set {W8, W9, W10, W11}. For data

reads, W8 and W9 are always directed to the X RAGU,

and W10 and W11 are always directed to the Y AGU.

The Effective Addresses generated (before and after

modification) must, therefore, be valid addresses within

X data space for W8 and W9 and Y data space for W10

and W11.

In summary, the following addressing modes are

supported by the MAC class of instructions:

• Register Indirect

• Register Indirect Post-Modified by 2

• Register Indirect Post-Modified by 4

• Register Indirect Post-Modified by 6

• Register Indirect with Register Offset (Indexed)

4.5.5 OTHER INSTRUCTIONS

Besides the addressing modes outlined previously, some

instructions use literal constants of various sizes. For

example, BRA (branch) instructions use 16-bit signed

literals to specify the branch destination directly, whereas

the DISI instruction uses a 14-bit unsigned literal field. In

some instructions, such as ULNK, the source of an

operand or result is implied by the opcode itself. Certain

operations, such as NOP, do not have any operands.

Addressing Mode Description

File Register Direct The address of the file register is specified explicitly.

or decremented) by a constant value.

to form the EA.

(Register Indexed)

The sum of Wn and Wb forms the EA.

Note: For the MOV instructions, the addressing

mode specified in the instruction can differ

for the source and destination EA.

However, the 4-bit Wb (Register Offset)

field is shared by both source and

destination (but typically only used by

one).

Note: Not all instructions support all the

addressing modes given above. Individual

instructions may support different subsets

of these addressing modes.

Note: Register Indirect with Register Offset

Addressing mode is available only for W9

(in X space) and W11 (in Y space).

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 130  2009-2012 Microchip Technology Inc.

4.6 Modulo Addressing

(dsPIC33EPXXXMU806/810/814

Devices Only)

Modulo Addressing mode is a method of providing an

automated means to support circular data buffers using

hardware. The objective is to remove the need for

software to perform data address boundary checks

when executing tightly looped code, as is typical in

many DSP algorithms.

Modulo Addressing can operate in either data or

Program Space (since the Data Pointer mechanism is

essentially the same for both). One circular buffer can be

supported in each of the X (which also provides the point-

ers into Program Space) and Y data spaces. Modulo

Addressing can operate on any W Register Pointer. How-

ever, it is not advisable to use W14 or W15 for Modulo

Addressing since these two registers are used as the

Stack Frame Pointer and Stack Pointer, respectively.

In general, any particular circular buffer can be config-

ured to operate in only one direction as there are

certain restrictions on the buffer start address (for incre-

menting buffers), or end address (for decrementing

buffers), based upon the direction of the buffer.

The only exception to the usage restrictions is for

buffers that have a power-of-two length. As these

buffers satisfy the start and end address criteria, they

can operate in a bidirectional mode (that is, address

boundary checks are performed on both the lower and

upper address boundaries).

4.6.1 START AND END ADDRESS

The Modulo Addressing scheme requires that a

starting and ending address be specified and loaded

into the 16-bit Modulo Buffer Address registers:

XMODSRT, XMODEND, YMODSRT and YMODEND

(see Ta bl e 4 -1 ).

The length of a circular buffer is not directly specified. It

is determined by the difference between the

corresponding start and end addresses. The maximum

possible length of the circular buffer is 32K words

(64 Kbytes).

4.6.2 W ADDRESS REGISTER

SELECTION

The Modulo and Bit-Reversed Addressing Control

as a W register field to specify the W Address registers.

The XWM and YWM fields select the registers that

operate with Modulo Addressing:

•If XWM = 1111, X RAGU and X WAGU Modulo

Addressing is disabled.

•If YWM = 1111, Y AGU Modulo Addressing is

disabled.

The X Address Space Pointer W register (XWM), to

which Modulo Addressing is to be applied, is stored in

MODCON<3:0> (see Table 4-1). Modulo Addressing is

enabled for X data space when XWM is set to any value

other than ‘1111’ and the XMODEN bit is set at

MODCON<15>.

The Y Address Space Pointer W register (YWM) to

which Modulo Addressing is to be applied is stored in

MODCON<7:4>. Modulo Addressing is enabled for Y

data space when YWM is set to any value other than

‘1111’ and the YMODEN bit is set at MODCON<14>.

FIGURE 4-10: MODULO ADDRESSING OPERATION EXAMPLE

Note: Y space Modulo Addressing EA calcula-

tions assume word-sized data (LSb of

every EA is always clear).

0x1100

0x1163

Start Addr = 0x1100

End Addr = 0x1163

Length = 0x0032 words

Byte

Address

MOV #0x1100, W0

MOV W0, XMODSRT ;set modulo start address

MOV #0x1163, W0

MOV W0, MODEND ;set modulo end address

MOV #0x8001, W0

MOV W0, MODCON ;enable W1, X AGU for modulo

MOV #0x0000, W0 ;W0 holds buffer fill value

MOV #0x1110, W1 ;point W1 to buffer

DO AGAIN, #0x31 ;fill the 50 buffer locations

MOV W0, [W1++] ;fill the next location

AGAIN: INC W0, W0 ;increment the fill value

 2009-2012 Microchip Technology Inc. DS70616G-page 131

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

4.6.3 MODULO ADDRESSING

APPLICABILITY

Modulo Addressing can be applied to the Effective

Address (EA) calculation associated with any W

equal to:

• The upper boundary addresses for incrementing

buffers

• The lower boundary addresses for decrementing

buffers

It is important to realize that the address boundaries

check for addresses less than or greater than the upper

(for incrementing buffers) and lower (for decrementing

buffers) boundary addresses (not just equal to).

Address changes can, therefore, jump beyond

boundaries and still be adjusted correctly.

4.7 Bit-Reversed Addressing

(dsPIC33EPXXXMU806/810/814

Devices Only)

Bit-Reversed Addressing mode is intended to simplify

data reordering for radix-2 FFT algorithms. It is

supported by the X AGU for data writes only.

The modifier, which can be a constant value or register

contents, is regarded as having its bit order reversed.

The address source and destination are kept in normal

order. Thus, the only operand requiring reversal is the

modifier.

4.7.1 BIT-REVERSED ADDRESSING

IMPLEMENTATION

Bit-Reversed Addressing mode is enabled in any of

these situations:

• BWMx bits (W register selection) in the MODCON

cannot be accessed using Bit-Reversed

Addressing)

• The BREN bit is set in the XBREV register

• The addressing mode used is Register Indirect

with Pre-Increment or Post-Increment

If the length of a bit-reversed buffer is M = 2N bytes,

the last ‘N’ bits of the data buffer start address must

be zeros.

XB<14:0> is the Bit-Reversed Address modifier, or

‘pivot point,’ which is typically a constant. In the case of

an FFT computation, its value is equal to half of the FFT

data buffer size.

When enabled, Bit-Reversed Addressing is executed

only for Register Indirect with Pre-Increment or Post-

Increment Addressing and word-sized data writes. It

does not function for any other addressing mode or for

byte-sized data and normal addresses are generated

instead. When Bit-Reversed Addressing is active, the

W Address Pointer is always added to the address

modifier (XB) and the offset associated with the

addition, as word-sized data is a requirement, the LSb

of the EA is ignored (and always clear).

If Bit-Reversed Addressing has already been enabled

by setting the BREN (XBREV<15>) bit, a write to the

XBREV register should not be immediately followed by

an indirect read operation using the W register that has

been designated as the Bit-Reversed Pointer.

Note: The modulo corrected Effective Address

is written back to the register only when

Pre-Modify or Post-Modify Addressing

mode is used to compute the Effective

Address. When an address offset (such

as [W7 + W2]) is used, Modulo

Addressing correction is performed but

the contents of the register remain

unchanged.

Note: All bit-reversed EA calculations assume

word-sized data (LSb of every EA is

always clear). The XB value is scaled

accordingly to generate compatible (byte)

addresses.

Note: Modulo Addressing and Bit-Reversed

Addressing can be enabled simultaneously

using the same W register, but Bit-

Reversed Addressing operation will always

take precedence for data writes when

enabled.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 132  2009-2012 Microchip Technology Inc.

FIGURE 4-11: BIT-REVERSED ADDRESS EXAMPLE

TABLE 4-76: BIT-REVERSED ADDRESS SEQUENCE (16-ENTRY)

Normal Address Bit-Reversed Address

A3 A2 A1 A0 Decimal A3 A2 A1 A0 Decimal

0000 00000 0

0001 11000 8

0010 20100 4

0011 31100 12

0100 40010 2

0101 51010 10

0110 60110 6

0111 71110 14

1000 80001 1

1001 91001 9

1010 10 0101 5

1011 11 1101 13

1100 12 0011 3

1101 13 1011 11

1110 14 0111 7

1111 15 1111 15

b3 b2 b1 0

b2 b3 b4 0

Bit Locations Swapped Left-to-Right

Around Center of Binary Value

Bit-Reversed Address

XB = 0x0008 for a 16-Word Bit-Reversed Buffer

b7 b6 b5 b1

b7 b6 b5 b4

b11 b10 b9 b8

b15 b14 b13 b12

Sequential Address

Pivot Point

 2009-2012 Microchip Technology Inc. DS70616G-page 133

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

4.8 Interfacing Program and Data

Memory Spaces

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 architecture uses a

24-bit wide Program Space and a 16-bit wide data

space. The architecture is also a modified Harvard

scheme, meaning that data can also be present in the

Program Space. To use this data successfully, it must

be accessed in a way that preserves the alignment of

information in both spaces.

Aside from normal execution, the

dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 architecture provides

two methods by which Program Space can be

accessed during operation:

• Using table instructions to access individual bytes

or words anywhere in the Program Space

• Remapping a portion of the Program Space into

the data space (Program Space Visibility)

Table instructions allow an application to read or write

to small areas of the program memory. This capability

makes the method ideal for accessing data tables that

need to be updated periodically. It also allows access

to all bytes of the program word. The remapping

method allows an application to access a large block of

data on a read-only basis, which is ideal for look-ups

from a large table of static data. The application can

only access the least significant word of the program

word.

TABLE 4-77: PROGRAM SPACE ADDRESS CONSTRUCTION

FIGURE 4-12: DATA ACCESS FROM PROGRAM SPACE ADDRESS GENERATION

Access Type Access

Space

Program Space Address

<23> <22:16> <15> <14:1> <0>

Instruction Access

(Code Execution)

User 0PC<22:1> 0

0xx xxxx xxxx xxxx xxxx xxx0

TBLRD/TBLWT

(Byte/Word Read/Write)

User TBLPAG<7:0> Data EA<15:0>

0xxx xxxx xxxx xxxx xxxx xxxx

Configuration TBLPAG<7:0> Data EA<15:0>

1xxx xxxx xxxx xxxx xxxx xxxx

0Program Counter

23 Bits

Program Counter(1)

TBLPAG

8 Bits

16 Bits

Byte Select

1/0

User/Configuration Space Select

Table Operations(2)

24 Bits

1/0

Note 1: The Least Significant bit (LSb) of Program Space addresses is always fixed as ‘0’ to maintain word

alignment of data in the program and data spaces.

2: Table operations are not required to be word-aligned. Table read operations are permitted in the

configuration memory space.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 134  2009-2012 Microchip Technology Inc.

4.8.1 DATA ACCESS FROM PROGRAM

MEMORY USING TABLE

INSTRUCTIONS

The TBLRDL and TBLWTL instructions offer a direct

method of reading or writing the lower word of any

address within the Program Space without going

through data space. The TBLRDH and TBLWTH

instructions are the only method to read or write the

upper 8 bits of a Program Space word as data.

The PC is incremented by two for each successive

24-bit program word. This allows program memory

addresses to directly map to data space addresses.

Program memory can thus be regarded as two 16-bit

wide word address spaces, residing side by side, each

with the same address range. TBLRDL and TBLWTL

access the space that contains the least significant

data word. TBLRDH and TBLWTH access the space that

contains the upper data byte.

Two table instructions are provided to move byte or

word-sized (16-bit) data to and from Program Space.

Both function as either byte or word operations.

•TBLRDL (Table Read Low):

- In Word mode, this instruction maps the

lower word of the Program Space

location (P<15:0>) to a data address

(D<15:0>).

- In Byte mode, either the upper or lower byte

of the lower program word is mapped to the

lower byte of a data address. The upper byte

is selected when Byte Select is ‘1’; the lower

byte is selected when it is ‘0’.

•TBLRDH (Table Read High):

- In Word mode, this instruction maps the entire

upper word of a program address (P<23:16>)

to a data address. The ‘phantom’ byte

(D<15:8>), is always ‘0’.

- In Byte mode, this instruction maps the upper

or lower byte of the program word to D<7:0>

of the data address, in the TBLRDL instruc-

tion. The data is always ‘0’ when the upper

‘phantom’ byte is selected (Byte Select = 1).

In a similar fashion, two table instructions, TBLWTH

and TBLWTL, are used to write individual bytes or

words to a Program Space address. The details of

their operation are explained in Section 5.0 “Flash

Program Memory”.

For all table operations, the area of program memory

space to be accessed is determined by the Table Page

memory space of the device, including user application

and configuration spaces. When TBLPAG<7> = 0, the

table page is located in the user memory space. When

TBLPAG<7> = 1, the page is located in configuration

space.

FIGURE 4-13: ACCESSING PROGRAM MEMORY WITH TABLE INSTRUCTIONS

081623

00000000

‘Phantom’ Byte

TBLRDH.B (Wn<0> = 0)

TBLRDL.W

TBLRDL.B (Wn<0> = 1)

TBLRDL.B (Wn<0> = 0)

23 15 0

TBLPAG

0x000000

0x800000

0x020000

0x030000

Program Space

The address for the table operation is determined by the data EA

within the page defined by the TBLPAG register.

Only read operations are shown; write operations are also valid in

the user memory area.

 2009-2012 Microchip Technology Inc. DS70616G-page 135

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

5.0 FLASH PROGRAM MEMORY

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices contain

internal Flash program memory for storing and

executing application code. The memory is readable,

writable and erasable during normal operation over the

entire VDD range.

Flash memory can be programmed in two ways:

• In-Circuit Serial Programming™ (ICSP™)

programming capability

• Run-Time Self-Programming (RTSP)

ICSP allows a dsPIC33EPXXX(GP/MC/MU)806/810/

814 and PIC24EPXXX(GP/GU)810/814 device to be

serially programmed while in the end application circuit.

This is done with two lines for programming clock and

programming data (one of the alternate programming

pin pairs: PGECx/PGEDx), and three other lines for

power (VDD), ground (VSS) and Master Clear (MCLR).

This allows customers to manufacture boards with

unprogrammed devices and then program the device

just before shipping the product. This also allows the

most recent firmware or a custom firmware to be

programmed.

RTSP is accomplished using TBLRD (table read) and

TBLWT (table write) instructions. With RTSP, the user

application can write program memory data either in

blocks or ‘rows’ of 128 instructions (384 bytes) at a time

or a single program memory word, and erase program

memory in blocks or ‘pages’ of 1024 instructions

(3072 bytes) at a time.

5.1 Table Instructions and Flash

Programming

Regardless of the method used, all programming of

Flash memory is done with the table read and table

write instructions. These allow direct read and write

access to the program memory space from the data

memory while the device is in normal operating mode.

The 24-bit target address in the program memory is

formed using bits<7:0> of the TBLPAG register and the

Effective Address (EA) from a W register, specified in

the table instruction, as shown in Figure 5-1.

The TBLRDL and the TBLWTL instructions are used to

read or write to bits<15:0> of program memory.

TBLRDL and TBLWTL can access program memory in

both Word and Byte modes.

The TBLRDH and TBLWTH instructions are used to read

or write to bits<23:16> of program memory. TBLRDH

and TBLWTH can also access program memory in Word

or Byte mode.

FIGURE 5-1: ADDRESSING FOR TABLE REGISTERS

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this data

sheet, refer to Section 5. “Flash Pro-

gramming” (DS70609) of the “dsPIC33E/

PIC24E Family Reference Manual”, which

is available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

0Program Counter

24 Bits

Program Counter

TBLPAG Reg

8 Bits

Working Reg EA

16 Bits

Byte

24-Bit EA

1/0

Select

Using

Table Instruction

Using

User/Configuration

Space Select

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 136  2009-2012 Microchip Technology Inc.

5.2 RTSP Operation

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 Flash program memory

array is organized into rows of 128 instructions or

384 bytes. RTSP allows the user application to erase a

page of memory, which consists of eight rows

(1024 instructions) at a time, and to program one row

or one word at a time. Table 32-12 lists typical erase and

programming times. The 8-row erase pages and single

row write rows are edge-aligned from the beginning of

program memory, on boundaries of 3072 bytes and

384 bytes, respectively.

The program memory implements holding buffers,

which are located in the write latch area, that can con-

tain 128 instructions of programming data. Prior to the

actual programming operation, the write data must be

loaded into the buffers sequentially. The instruction

words loaded must always be from a group of

64 boundary.

The basic sequence for RTSP programming is to set up

a Table Pointer, then do a series of TBLWT instructions

to load the buffers. Programming is performed by

setting the control bits in the NVMCON register. A total

of 128 TBLWTL and TBLWTH instructions are required

to load the instructions.

All of the table write operations are single-word writes

(two instruction cycles) because only the buffers are

written. A programming cycle is required for program-

ming each row. For more information on erasing and

programming Flash memory, refer to Section 5.

“Flash Programming” (DS70609) in the “dsPIC33E/

PIC24E Family Reference Manual”.

5.3 Programming Operations

A complete programming sequence is necessary for

programming or erasing the internal Flash in RTSP

mode. The processor stalls (waits) until the

programming operation is finished.

The programming time depends on the FRC accuracy

(see Table 32-19) and the value of the FRC Oscillator

Tuning register (see Register 9-4). Use the following

formula to calculate the minimum and maximum values

for the Row Write Time, Page Erase Time and Word

Write Cycle Time parameters (see Table 32-12).

EQUATION 5-1: PROGRAMMING TIME

For example, if the device is operating at +125°C, the

FRC accuracy will be ±5%. If the TUN<5:0> bits (see

write time is equal to Equation 5-2.

EQUATION 5-2: MINIMUM ROW WRITE

TIME

The maximum row write time is equal to Equation 5-3.

EQUATION 5-3: MAXIMUM ROW WRITE

TIME

Setting the WR bit (NVMCON<15>) starts the

operation and the WR bit is automatically cleared

when the operation is finished.

7.37 MHz FRC Accuracy%FRC Tuning%

--------------------------------------------------------------------------------------------------------------------------

TRW

11064 Cycles

7.37 MHz 10.05+1 0.00375–

---------------------------------------------------------------------------------------------- 1.435ms==

TRW

11064 Cycles

7.37 MHz 10.05–1 0.00375–

----------------------------------------------------------------------------------------------1.586ms==

 2009-2012 Microchip Technology Inc. DS70616G-page 137

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

5.4 Flash Program Memory

Resources

Many useful resources related to Flash program

memory are provided on the main product page of the

Microchip web site for the devices listed in this data

sheet. This product page, which can be accessed using

this link, contains the latest updates and additional

information.

5.4.1 KEY RESOURCES

• Section 5. “Flash Programming” (DS70609) in

the “dsPIC33E/PIC24E Family Reference

Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

5.5 Control Registers

Four SFRs are used to read and write the program

Flash memory: NVMCON, NVMKEY, NVMADRU and

NVMADR.

The NVMCON register (Register 5-1) controls which

blocks are to be erased, which memory type is to be

programmed and the start of the programming cycle.

NVMKEY (Register 5-4) is a write-only register that is

used for write protection. To start a programming or

erase sequence, the user application must

consecutively write 0x55 and 0xAA to the NVMKEY

There are two NVM Address registers: NVMADRU and

NVMADR. These two registers, when concatenated,

form the 24-bit Effective Address (EA) of the selected

row or word for programming operations, or the

selected page for erase operations.

The NVMADRU register is used to hold the upper 8 bits

of the EA, while the NVMADR register is used to hold

the lower 16 bits of the EA.

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 138  2009-2012 Microchip Technology Inc.

R/SO-0(1)R/W-0(1)R/W-0(1)R/W-0 U-0 U-0 U-0 U-0

WR WREN WRERR NVMSIDL(2)— — — —

bit 15 bit 8

U-0 U-0 U-0 U-0 R/W-0(1)R/W-0(1)R/W-0(1)R/W-0(1)

— — — —NVMOP<3:0>

(3,4)

bit 7 bit 0

Legend: SO = Settable Only bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 WR: Write Control bit(1)

1 = Initiates a Flash memory program or erase operation; the operation is self-timed and the bit is

cleared by hardware once operation is complete

0 = Program or erase operation is complete and inactive

bit 14 WREN: Write Enable bit(1)

1 = Enables Flash program/erase operations

0 = Inhibits Flash program/erase operations

bit 13 WRERR: Write Sequence Error Flag bit(1)

1 = An improper program or erase sequence attempt or termination has occurred (bit is set automatically

on any set attempt of the WR bit)

0 = The program or erase operation completed normally

bit 12 NVMSIDL: NVM Stop-in-Idle Control bit(2)

1 = Flash voltage regulator goes into Stand-by mode during Idle mode

0 = Flash voltage regulator is active during Idle mode

bit 11-4 Unimplemented: Read as ‘0’

bit 3-0 NVMOP<3:0>: NVM Operation Select bits(1,3,4)

1111 = Reserved

1110 = Reserved

1101 = Bulk erase primary program Flash memory

1100 = Reserved

1011 = Reserved

1010 = Bulk erase auxiliary program Flash memory

0011 = Memory page erase operation

0010 = Memory row program operation

0001 = Memory word program operation(5)

0000 = Program a single Configuration register byte

Note 1: These bits can only be reset on a POR.

2: If this bit is set, upon exiting Idle mode, there is a delay (TVREG) before Flash memory becomes

operational.

3: All other combinations of NVMOP<3:0> are unimplemented.

4: Execution of the PWRSAV instruction is ignored while any of the NVM operations are in progress.

5: Two adjacent words are programmed during execution of this operation.

 2009-2012 Microchip Technology Inc. DS70616G-page 139

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

NVMADRU<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7-0 NVMADRU<7:0>: Nonvolatile Memory Upper Write Address bits

Selects the upper 8 bits of the location to program or erase in program Flash memory. This register

may be read or written by the user application.

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

NVMADR<15:8>

bit 15 bit 8

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

NVMADR<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 NVMADR<15:0>: Nonvolatile Memory Write Address bits

Selects the lower 16 bits of the location to program or erase in program Flash memory. This register

may be read or written by the user application.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0

NVMKEY<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7-0 NVMKEY<7:0>: Key Register (write-only) bits

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 140  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 141

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

6.0 RESETS The Reset module combines all Reset sources and

controls the device Master Reset Signal, SYSRST. The

following is a list of device Reset sources:

• POR: Power-on Reset

• BOR: Brown-out Reset

•MCLR: Master Clear Pin Reset

•SWR: RESET Instruction

• WDTO: Watchdog Timer Reset

• CM: Configuration Mismatch Reset

• TRAPR: Trap Conflict Reset

• IOPUWR: Illegal Condition Device Reset

- Illegal Opcode Reset

- Uninitialized W Register Reset

- Security Reset

A simplified block diagram of the Reset module is

shown in Figure 6-1.

Any active source of Reset will make the SYSRST sig-

nal active. On system Reset, some of the registers

associated with the CPU and peripherals are forced to

a known Reset state and some are unaffected.

FIGURE 6-1: RESET SYSTEM BLOCK DIAGRAM

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this

data sheet, refer to Section 8. “Reset”

(DS70602) of the “dsPIC33E/PIC24E

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Note: Refer to the specific peripheral section or

Section 4.0 “Memory Organization” of

this manual for register Reset states.

MCLR

VDD

Internal

Regulator

BOR

Sleep or Idle

RESET Instruction

WDT

Module

Glitch Filter

Trap Conflict

Illegal Opcode

Uninitialized W Register

SYSRST

VDD Rise

Detect

POR

Configuration Mismatch

Security Reset

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 142  2009-2012 Microchip Technology Inc.

6.1 Resets Resources

Many useful resources related to Resets are provided

on the main product page of the Microchip web site for

the devices listed in this data sheet. This product page,

which can be accessed using this link, contains the

latest updates and additional information.

6.1.1 KEY RESOURCES

• Section 8. “Reset” (DS70602) in the “dsPIC33E/

PIC24E Family Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

6.2 RCON Control Register

All types of device Resets set a corresponding status

bit in the RCON register to indicate the type of Reset

(see Register 6-1).

A POR clears all the bits, except for the POR and BOR

bits (RCON<1:0>), that are set. The user application

can set or clear any bit at any time during code

execution. The RCON bits only serve as status bits.

Setting a particular Reset status bit in software does

not cause a device Reset to occur.

The RCON register also has other bits associated with

the Watchdog Timer and device power-saving states.

The function of these bits is discussed in other sections

of this manual.

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

Note: The status bits in the RCON register

should be cleared after they are read so

that the next RCON register value after a

device Reset is meaningful.

 2009-2012 Microchip Technology Inc. DS70616G-page 143

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 U-0 U-0 R/W-0 U-0 R/W-0 R/W-0

TRAPR IOPUWR ——VREGSF —CMVREGS

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-1 R/W-1

EXTR SWR SWDTEN(2)WDTO SLEEP IDLE BOR POR

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 TRAPR: Trap Reset Flag bit

1 = A Trap Conflict Reset has occurred

0 = A Trap Conflict Reset has not occurred

bit 14 IOPUWR: Illegal Opcode or Uninitialized W Access Reset Flag bit

1 = An illegal opcode detection, an illegal address mode or uninitialized W register used as an

Address Pointer caused a Reset

0 = An illegal opcode or uninitialized W Reset has not occurred

bit 13-12 Unimplemented: Read as ‘0’

bit 11 VREGSF: Flash Voltage Regulator Standby During Sleep bit

1 = Flash voltage regulator is active during Sleep

0 = Flash voltage regulator goes into Standby mode during Sleep

bit 10 Unimplemented: Read as ‘0’

bit 9 CM: Configuration Mismatch Flag bit

1 = A Configuration Mismatch Reset has occurred.

0 = A Configuration Mismatch Reset has NOT occurred

bit 8 VREGS: Voltage Regulator Standby During Sleep bit

1 = Voltage regulator is active during Sleep

0 = Voltage regulator goes into Standby mode during Sleep

bit 7 EXTR: External Reset (MCLR) Pin bit

1 = A Master Clear (pin) Reset has occurred

0 = A Master Clear (pin) Reset has not occurred

bit 6 SWR: Software Reset (Instruction) Flag bit

1 = A RESET instruction has been executed

0 = A RESET instruction has not been executed

bit 5 SWDTEN: Software Enable/Disable of WDT bit(2)

1 = WDT is enabled

0 = WDT is disabled

bit 4 WDTO: Watchdog Timer Time-out Flag bit

1 = WDT time-out has occurred

0 = WDT time-out has not occurred

Note 1: All of the Reset status bits can be set or cleared in software. Setting one of these bits in software does not

cause a device Reset.

2: If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the

SWDTEN bit setting.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 144  2009-2012 Microchip Technology Inc.

bit 3 SLEEP: Wake-up from Sleep Flag bit

1 = Device has been in Sleep mode

0 = Device has not been in Sleep mode

bit 2 IDLE: Wake-up from Idle Flag bit

1 = Device was in Idle mode

0 = Device was not in Idle mode

bit 1 BOR: Brown-out Reset Flag bit

1 = A Brown-out Reset has occurred

0 = A Brown-out Reset has not occurred

bit 0 POR: Power-on Reset Flag bit

1 = A Power-on Reset has occurred

0 = A Power-on Reset has not occurred

Note 1: All of the Reset status bits can be set or cleared in software. Setting one of these bits in software does not

cause a device Reset.

2: If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the

SWDTEN bit setting.

 2009-2012 Microchip Technology Inc. DS70616G-page 145

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

7.0 INTERRUPT CONTROLLER

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 interrupt controller

reduces the numerous peripheral interrupt request

signals to a single interrupt request signal to

the dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 CPU.

The interrupt controller has the following features:

• Up to eight processor exceptions and software

traps

• Eight user-selectable priority levels

• Interrupt Vector Table (IVT) with a unique vector

for each interrupt or exception source

• Fixed priority within a specified user priority level

• Fixed interrupt entry and return latencies

7.1 Interrupt Vector Table

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 Interrupt Vector Table

(IVT), shown in Figure 7-1, resides in the General

Segment of program memory, starting at location,

0x000004, and is used when executing code from the

General Segment. The IVT contains seven non-

maskable trap vectors and up to 114 sources of

interrupt. In general, each interrupt source has its own

vector. Each interrupt vector contains a 24-bit wide

address. The value programmed into each interrupt

vector location is the starting address of the associated

Interrupt Service Routine (ISR).

Interrupt vectors are prioritized in terms of their natural

priority. This priority is linked to their position in the

vector table. Lower addresses generally have a higher

natural priority. For example, the interrupt associated

with vector 0 takes priority over interrupts at any other

vector address.

7.2 Auxiliary Interrupt Vector

When code is being executed in the Auxiliary Segment,

a special single interrupt vector, located at address,

0x7FFFFA, is used for all interrupt sources and traps.

Once vectored to this single routine, the

VECNUM<7:0> bits (INTTREG<7:0>, Register 7-7)

can be examined to determine the source of the

interrupt or trap so that it can be properly processed.

7.3 Reset Sequence

A device Reset is not a true exception because the

interrupt controller is not involved in the Reset process.

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices clear their

registers in response to a Reset, which forces the PC

to zero. The digital signal controller then begins

program execution at location, 0x000000. A GOTO

instruction at the Reset address can redirect program

execution to the appropriate start-up routine.

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this

data sheet, refer to Section 6. “Inter-

rupts” (DS70600) of the “dsPIC33E/

PIC24E Family Reference Manual”,

which is available from the Microchip web

site (www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Note: Any unimplemented or unused vector

locations in the IVT should be

programmed with the address of a default

interrupt handler routine that contains a

RESET instruction.

Note: Reset locations are also located in the

Auxiliary Segment at the addresses

0x7FFFFC and 0x7FFFFE. The Reset

Target Vector Select bit, RSTPRI

(FICD<2>) controls whether the primary

(General Segment) or Auxiliary Segment

Reset location is used.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 146  2009-2012 Microchip Technology Inc.

FIGURE 7-1: dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

INTERRUPT VECTOR TABLE

IVT

Decreasing Natural Order Priority

Reset – GOTO Instruction(1)0x000000

Reset – GOTO Address(1)0x000002

Oscillator Fail Trap Vector 0x000004

Address Error Trap Vector 0x000006

Generic Hard Trap Vector 0x000008

Stack Error Trap Vector 0x00000A

Math Error Trap Vector 0x00000C

DMAC Error Trap Vector 0x00000E

Generic Soft Trap Vector 0x000010

Reserved 0x000012

Interrupt Vector 0 0x000014

Interrupt Vector 1 0x000016

Interrupt Vector 52 0x00007C

Interrupt Vector 53 0x00007E

Interrupt Vector 54 0x000080

Interrupt Vector 116 0x0000FC

Interrupt Vector 117 0x0000FE

Interrupt Vector 118 0x000100

Interrupt Vector 119 0x000102

Interrupt Vector 120 0x000104

Interrupt Vector 244 0x0001FC

Interrupt Vector 245 0x0001FE

START OF CODE 0x000200

See Tab l e 7- 1 for

Interrupt Vector Details

Note 1: Reset locations are also located in the Auxiliary Segment at the addresses 0x7FFFFC and

0x7FFFFE. The Reset Target Vector Select bit, RSTPRI (FICD<2>) controls whether the

primary (General Segment) or Auxiliary Segment Reset location is used.

 2009-2012 Microchip Technology Inc. DS70616G-page 147

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 7-1: INTERRUPT VECTOR DETAILS

Interrupt Source Vector

#IRQ # IVT

Address

Interrupt Bit Location

Flag Enable Priority

Highest Natural Order Priority

INT0 – External Interrupt 0 8 0 0x000014 IFS0<0> IEC0<0> IPC0<2:0>

IC1 – Input Capture 1 9 1 0x000016 IFS0<1> IEC0<1> IPC0<6:4>

OC1 – Output Compare 1 10 2 0x000018 IFS0<2> IEC0<2> IPC0<10:8>

T1 – Timer1 11 3 0x00001A IFS0<3> IEC0<3> IPC0<14:12>

DMA0 – DMA Channel 0 12 4 0x00001C IFS0<4> IEC0<4> IPC1<2:0>

IC2 – Input Capture 2 13 5 0x00001E IFS0<5> IEC0<5> IPC1<6:4>

OC2 – Output Compare 2 14 6 0x000020 IFS0<6> IEC0<6> IPC1<10:8>

T2 – Timer2 15 7 0x000022 IFS0<7> IEC0<7> IPC1<14:12>

T3 – Timer3 16 8 0x000024 IFS0<8> IEC0<8> IPC2<2:0>

SPI1E – SPI1 Error 17 9 0x000026 IFS0<9> IEC0<9> IPC2<6:4>

SPI1 – SPI1 Transfer Done 18 10 0x000028 IFS0<10> IEC0<10> IPC2<10:8>

U1RX – UART1 Receiver 19 11 0x00002A IFS0<11> IEC0<11> IPC2<14:12>

U1TX – UART1 Transmitter 20 12 0x00002C IFS0<12> IEC0<12> IPC3<2:0>

AD1 – ADC1 Convert Done 21 13 0x00002E IFS0<13> IEC0<13> IPC3<6:4>

DMA1 – DMA Channel 1 22 14 0x000030 IFS0<14> IEC0<14> IPC3<10:8>

NVM – NVM Write Complete 23 15 0x000032 IFS0<15> IEC0<15> IPC3<14:12>

SI2C1 – I2C1 Slave Event 24 16 0x000034 IFS1<0> IEC1<0> IPC4<2:0>

MI2C1 – I2C1 Master Event 25 17 0x000036 IFS1<1> IEC1<1> IPC4<6:4>

CM – Comparator Combined Event 26 18 0x000038 IFS1<2> IEC1<2> IPC4<10:8>

CN – Input Change Interrupt 27 19 0x00003A IFS1<3> IEC1<3> IPC4<14:12>

INT1 – External Interrupt 1 28 20 0x00003C IFS1<4> IEC1<4> IPC5<2:0>

AD2 – ADC2 Convert Done 29 21 0x00003E IFS1<5> IEC1<5> IPC5<6:4>

IC7 – Input Capture 7 30 22 0x000040 IFS1<6> IEC1<6> IPC5<10:8>

IC8 – Input Capture 8 31 23 0x000042 IFS1<7> IEC1<7> IPC5<14:12>

DMA2 – DMA Channel 2 32 24 0x000044 IFS1<8> IEC1<8> IPC6<2:0>

OC3 – Output Compare 3 33 25 0x000046 IFS1<9> IEC1<9> IPC6<6:4>

OC4 – Output Compare 4 34 26 0x000048 IFS1<10> IEC1<10> IPC6<10:8>

T4 – Timer4 35 27 0x00004A IFS1<11> IEC1<11> IPC6<14:12>

T5 – Timer5 36 28 0x00004C IFS1<12> IEC1<12> IPC7<2:0>

INT2 – External Interrupt 2 37 29 0x00004E IFS1<13> IEC1<13> IPC7<6:4>

U2RX – UART2 Receiver 38 30 0x000050 IFS1<14> IEC1<14> IPC7<10:8>

U2TX – UART2 Transmitter 39 31 0x000052 IFS1<15> IEC1<15> IPC7<14:12>

SPI2E – SPI2 Error 40 32 0x000054 IFS2<0> IEC2<0> IPC8<2:0>

SPI2 – SPI2 Transfer Done 41 33 0x000056 IFS2<1> IEC2<1> IPC8<6:4>

C1RX – CAN1 RX Data Ready 42 34 0x000058 IFS2<2> IEC2<2> IPC8<10:8>

C1 – CAN1 Event 43 35 0x00005A IFS2<3> IEC2<3> IPC8<14:12>

DMA3 – DMA Channel 3 44 36 0x00005C IFS2<4> IEC2<4> IPC9<2:0>

IC3 – Input Capture 3 45 37 0x00005E IFS2<5> IEC2<5> IPC9<6:4>

IC4 – Input Capture 4 46 38 0x000060 IFS2<6> IEC2<6> IPC9<10:8>

IC5 – Input Capture 5 47 39 0x000062 IFS2<7> IEC2<7> IPC9<14:12>

IC6 – Input Capture 6 48 40 0x000064 IFS2<8> IEC2<8> IPC10<2:0>

Note 1: This interrupt source is available on dsPIC33EPXXX(MC/MU)806/810/814 devices only.

2: This interrupt source is available on dsPIC33EPXXXMU8XX and PIC24EPXXXGU8XX devices only.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 148  2009-2012 Microchip Technology Inc.

OC5 – Output Compare 5 49 41 0x000066 IFS2<9> IEC2<9> IPC10<6:4>

OC6 – Output Compare 6 50 42 0x000068 IFS2<10> IEC2<10> IPC10<10:8>

OC7 – Output Compare 7 51 43 0x00006A IFS2<11> IEC2<11> IPC10<14:12>

OC8 – Output Compare 8 52 44 0x00006C IFS2<12> IEC2<12> IPC11<2:0>

PMP – Parallel Master Port 53 45 0x00006E IFS2<13> IEC2<13> IPC11<6:4>

DMA4 – DMA Channel 4 54 46 0x000070 IFS2<14> IEC2<14> IPC11<10:8>

T6 – Timer6 55 47 0x000072 IFS2<15> IEC2<15> IPC11<14:12>

T7 – Timer7 56 48 0x000074 IFS3<0> IEC3<0> IPC12<2:0>

SI2C2 – I2C2 Slave Event 57 49 0x000076 IFS3<1> IEC3<1> IPC12<6:4>

MI2C2 – I2C2 Master Event 58 50 0x000078 IFS3<2> IEC3<2> IPC12<10:8>

T8 – Timer8 59 51 0x00007A IFS3<3> IEC3<3> IPC12<14:12>

T9 – Timer9 60 52 0x00007C IFS3<4> IEC3<4> IPC13<2:0>

INT3 – External Interrupt 3 61 53 0x00007E IFS3<5> IEC3<5> IPC13<6:4>

INT4 – External Interrupt 4 62 54 0x000080 IFS3<6> IEC3<6> IPC13<10:8>

C2RX – CAN2 RX Data Ready 63 55 0x000082 IFS3<7> IEC3<7> IPC13<14:12>

C2 – CAN2 Event 64 56 0x000084 IFS3<8> IEC3<8> IPC14<2:0>

PSEM – PWM Special Event Match(1)65 57 0x000086 IFS3<9> IEC3<9> IPC14<6:4>

QEI1 – QEI1 Position Counter

Compare(1)

66 58 0x000088 IFS3<10> IEC3<10> IPC14<10:8>

DCIE – DCI Fault Interrupt 67 59 0x00008A IFS3<11> IEC3<11> IPC14<14:12>

DCI – DCI Transfer Done 68 60 0x00008C IFS3<12> IEC3<12> IPC15<2:0>

DMA5 – DMA Channel 5 69 61 0x00008E IFS3<13> IEC3<13> IPC15<6:4>

RTC – Real-Time Clock and Calendar 70 62 0x000090 IFS3<14> IEC3<14> IPC15<10:8>

Reserved 71-72 63-64 0x000092-0x000094 — — —

U1E – UART1 Error Interrupt 73 65 0x000096 IFS4<1> IEC4<1> IPC16<6:4>

U2E – UART2 Error Interrupt 74 66 0x000098 IFS4<2> IEC4<2> IPC16<10:8>

CRC – CRC Generator Interrupt 75 67 0x00009A IFS4<3> IEC4<3> IPC16<14:12>

DMA6 – DMA Channel 6 76 68 0x00009C IFS4<4> IEC4<4> IPC17<2:0>

DMA7 – DMA Channel 7 77 69 0x00009E IFS4<5> IEC4<5> IPC17<6:4>

C1TX – CAN1 TX Data Request 78 70 0x0000A0 IFS4<6> IEC4<6> IPC17<10:8>

C2TX – CAN2 TX Data Request 79 71 0x0000A2 IFS4<7> IEC4<7> IPC17<14:12>

Reserved 80 72 0x0000A4 — — —

PSESM – PWM Secondary Special

Event Match(1)

81 73 0x0000A6 IFS4<9> IEC4<9> IPC18<6:4>

Reserved 82 74 0x0000A8 — — —

QEI2 – QEI2 Position Counter

Compare(1)

83 75 0x0000AA IFS4<11> IEC4<11> IPC18<14:12>

Reserved 84-88 76-80 0x0000AC-0x0000B4 — — —

U3E – UART3 Error Interrupt 89 81 0x0000B6 IFS5<1> IEC5<1> IPC20<6:4>

U3RX – UART3 Receiver 90 82 0x0000B8 IFS5<2> IEC5<2> IPC20<10:8>

U3TX – UART3 Transmitter 91 83 0x0000BA IFS5<3> IEC5<3> IPC20<14:12>

Reserved 9293 84-85 0x0000BC-0x0000BE — — —

TABLE 7-1: INTERRUPT VECTOR DETAILS (CONTINUED)

Interrupt Source Vector

#IRQ # IVT

Address

Interrupt Bit Location

Flag Enable Priority

Note 1: This interrupt source is available on dsPIC33EPXXX(MC/MU)806/810/814 devices only.

2: This interrupt source is available on dsPIC33EPXXXMU8XX and PIC24EPXXXGU8XX devices only.

 2009-2012 Microchip Technology Inc. DS70616G-page 149

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

USB1 – USB OTG Interrupt(2)94 86 0x0000C0 IFS5<6> IEC5<6> IPC21<10:8>

U4E – UART4 Error Interrupt 95 87 0x0000C2 IFS5<7> IEC5<7> IPC21<14:12>

U4RX – UART4 Receiver 96 88 0x0000C4 IFS5<8> IEC5<8> IPC22<2:0>

U4TX – UART4 Transmitter 97 89 0x0000C6 IFS5<9> IEC5<9> IPC22<6:4>

SPI3E – SPI3 Error 98 90 0x0000C8 IFS5<10> IEC5<10> IPC22<10:8>

SPI3 – SPI3 Transfer Done 99 91 0x0000CA IFS5<11> IEC5<11> IPC22<14:12>

OC9 – Output Compare 9 100 92 0x0000CC IFS5<12> IEC5<12> IPC23<2:0>

IC9 – Input Capture 9 101 93 0x0000CE IFS5<13> IEC5<13> IPC23<6:4>

PWM1 – PWM Generator 1(1)102 94 0x0000D0 IFS5<14> IEC5<14> IPC23<10:8>

PWM2 – PWM Generator 2(1)103 95 0x0000D2 IFS5<15> IEC5<15> IPC23<14:12>

PWM3 – PWM Generator 3(1)104 96 0x0000D4 IFS6<0> IEC6<0> IPC24<2:0>

PWM4 – PWM Generator 4(1)105 97 0x0000D6 IFS6<1> IEC6<1> IPC24<6:4>

PWM5 – PWM Generator 5(1)106 98 0x0000D8 IFS6<2> IEC6<2> IPC24<10:8>

PWM6 – PWM Generator 6(1)107 99 0x0000DA IFS6<3> IEC6<3> IPC24<14:12>

PWM7 – PWM Generator 7(1)108 100 0x0000DC IFS6<4> IEC6<4> IPC25<2:0>

Reserved 109-125 101-117 0x0000DE-0x0000FC — — —

DMA8 – DMA Channel 8 126 118 0x000100 IFS7<6> IEC7<6> IPC29<10:8>

DMA9 – DMA Channel 9 127 119 0x000102 IFS7<7> IEC7<7> IPC29<14:12>

DMA10 – DMA Channel 10 128 120 0x000104 IFS7<8> IEC7<8> IPC30<2:0>

DMA11 – DMA Channel 11 129 121 0x000106 IFS7<9> IEC7<9> IPC30<6:4>

SPI4E – SPI4 Error 130 122 0x000108 IFS7<10> IEC7<10> IPC30<10:8>

SPI4 – SPI4 Transfer Done 131 123 0x00010A IFS7<11> IEC7<11> IPC30<14:12>

OC10 – Output Compare 10 132 124 0x00010C IFS7<12> IEC7<12> IPC31<2:0>

IC10 – Input Capture 10 133 125 0x00010E IFS7<13> IEC7<13> IPC31<6:4>

OC11 – Output Compare11 134 126 0x000110 IFS7<14> IEC7<14> IPC31<10:8>

IC11 – Input Capture 11 135 127 0x000112 IFS7<15> IEC7<15> IPC31<14:12>

OC12 – Output Compare 12 136 128 0x000114 IFS8<0> IEC8<0> IPC32<2:0>

IC12 – Input Capture 12 137 129 0x000116 IFS8<1> IEC8<1> IPC32<6:4>

DMA12 – DMA Channel 12 138 130 0x000118 IFS8<2> IEC8<2> IPC32<10:8>

DMA13– DMA Channel 13 139 131 0x00011A IFS8<3> IEC8<3> IPC32<14:12>

DMA14 – DMA Channel 14 140 132 0x00011C IFS8<4> IEC8<4> IPC33<2:0>

Reserved 141 133 0x00011E — — —

OC13 – Output Compare 13 142 134 0x000120 IFS8<6> IEC8<6> IPC33<10:8>

IC13 – Input Capture 13 143 135 0x000122 IFS8<7> IEC8<7> IPC33<14:12>

OC14 – Output Compare14 144 136 0x000124 IFS8<8> IEC8<8> IPC34<2:0>

IC14 – Input Capture 14 145 137 0x000126 IFS8<9> IEC8<9> IPC34<6:4>

OC15 – Output Compare 15 146 138 0x000128 IFS8<10> IEC8<10> IPC34<10:8>

IC15 – Input Capture 15 147 139 0x00012A IFS8<11> IEC8<11> IPC34<14:12>

OC16 – Output Compare 16 148 140 0x00012C IFS8<12> IEC8<12> IPC35<2:0>

IC16 – Input Capture 16 149 141 0x00012E IFS8<13> IEC8<13> IPC35<6:4>

ICD – ICD Application 150 142 0x000130 IFS8<14> IEC8<14> IPC35<10:8>

Reserved 151-245 142-237 0x000130-0x0001FE — — —

Lowest Natural Order Priority

TABLE 7-1: INTERRUPT VECTOR DETAILS (CONTINUED)

Interrupt Source Vector

#IRQ # IVT

Address

Interrupt Bit Location

Flag Enable Priority

Note 1: This interrupt source is available on dsPIC33EPXXX(MC/MU)806/810/814 devices only.

2: This interrupt source is available on dsPIC33EPXXXMU8XX and PIC24EPXXXGU8XX devices only.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 150  2009-2012 Microchip Technology Inc.

7.4 Interrupt Resources

Many useful resources related to Interrupts are pro-

vided on the main product page of the Microchip web

site for the devices listed in this data sheet. This

product page, which can be accessed using this link,

contains the latest updates and additional information.

7.4.1 KEY RESOURCES

• Section 6. “Interrupts” (DS70600) in the

“dsPIC33E/PIC24E Family Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

7.5 Interrupt Control and Status

Registers

dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices implement

the following registers for the interrupt controller:

• INTCON1-INTCON4

•INTTREG

7.5.1 INTCON1 THROUGH INTCON4

Global interrupt control functions are controlled from

INTCON1, INTCON2, INTCON3 and INTCON4.

INTCON1 contains the Interrupt Nesting Disable bit

(NSTDIS) as well as the control and status flags for the

processor trap sources.

The INTCON2 register controls external interrupt

request signal behavior and software trap enable. This

(GIE).

INTCON3 contains the status flags for the USB, DMA

and DO stack overflow status trap sources.

The INTCON4 register contains the software

generated Hard Trap Status bit (SGHT).

7.5.2 IFSx

The IFS registers maintain all of the interrupt request

flags. Each source of interrupt has a status bit, which is

set by the respective peripherals or external signal and

is cleared via software.

7.5.3 IECx

The IEC registers maintain all of the interrupt enable

bits. These control bits are used to individually enable

interrupts from the peripherals or external signals.

7.5.4 IPCx

The IPC registers are used to set the Interrupt Priority

Level for each source of interrupt. Each user interrupt

source can be assigned to one of eight priority levels.

7.5.5 INTTREG

The INTTREG register contains the associated

interrupt vector number and the new CPU Interrupt

Priority Level, which are latched into the vector number

(VECNUM<7:0>) and Interrupt level bit (ILR<3:0>)

fields in the INTTREG register. The new Interrupt

Priority Level is the priority of the pending interrupt.

The interrupt sources are assigned to the IFSx, IECx

and IPCx registers in the same sequence as they are

listed in Tab l e 7 - 1. For example, the INT0 (External

Interrupt 0) is shown as having Vector Number 8 and a

natural order priority of 0. Thus, the INT0IF bit is found

in IFS0<0>, the INT0IE bit in IEC0<0> and the INT0IP

bits in the first position of IPC0 (IPC0<2:0>).

7.5.6 STATUS/CONTROL REGISTERS

Although these registers are not specifically part of the

interrupt control hardware, two of the CPU Control

registers contain bits that control interrupt functionality.

For more information on these registers refer to

Section 2. “CPU” (DS70359) in the “dsPIC33E/

PIC24E Family Reference Manual”.

• The CPU STATUS register, SR, contains the

IPL<2:0> bits (SR<7:5>). These bits indicate the

current CPU Interrupt Priority Level. The user

software can change the current CPU priority

level by writing to the IPL bits.

• The CORCON register contains the IPL3 bit

which, together with IPL<2:0>, also indicates the

current CPU priority level. IPL3 is a read-only bit

so that trap events cannot be masked by the user

software.

All Interrupt registers are described in Register 7-3

through Register 7-7 in the following pages.

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

 2009-2012 Microchip Technology Inc. DS70616G-page 151

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 R/W-0 R/C-0 R/C-0 R-0 R/W-0

OA OB SA SB OAB SAB DA DC

bit 15 bit 8

R/W-0(3)R/W-0(3)R/W-0(3)R-0 R/W-0 R/W-0 R/W-0 R/W-0

IPL<2:0>(2)RA NOV Z C

bit 7 bit 0

Legend: C = Clearable bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 7-5 IPL<2:0>: CPU Interrupt Priority Level Status bits(2,3)

111 = CPU Interrupt Priority Level is 7 (15, user interrupts are disabled)

110 = CPU Interrupt Priority Level is 6 (14)

101 = CPU Interrupt Priority Level is 5 (13)

100 = CPU Interrupt Priority Level is 4 (12)

011 = CPU Interrupt Priority Level is 3 (11)

010 = CPU Interrupt Priority Level is 2 (10)

001 = CPU Interrupt Priority Level is 1 (9)

000 = CPU Interrupt Priority Level is 0 (8)

Note 1: For complete register details, see Register 3-1: “SR: CPU Status Register”.

2: The IPL<2:0> bits are concatenated with the IPL<3> bit (CORCON<3>) to form the CPU Interrupt Priority

Level. The value in parentheses indicates the IPL, if IPL<3> = 1.

3: The IPL<2:0> Status bits are read-only when NSTDIS (INTCON1<15>) = 1.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 152  2009-2012 Microchip Technology Inc.

R/W-0 U-0 R/W-0 R/W-0 R/W-0 R-0 R-0 R-0

VAR —US<1:0> EDT DL<2:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-1 R/W-0 R/C-0 R-0 R/W-0 R/W-0

SATA SATB SATDW ACCSAT IPL3(2)SFA RND IF

bit 7 bit 0

Legend: C = Clearable bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 VAR: Variable Exception Processing Latency Control bit

1 = Variable exception processing is enabled

0 = Fixed exception processing is enabled

bit 3 IPL3: CPU Interrupt Priority Level Status bit 3(2)

1 = CPU Interrupt Priority Level is greater than 7

0 = CPU Interrupt Priority Level is 7 or less

Note 1: For complete register details, see Register 3-2: “CORCON: Core Control Register”.

2: The IPL3 bit is concatenated with the IPL<2:0> bits (SR<7:5>) to form the CPU Interrupt Priority Level.

 2009-2012 Microchip Technology Inc. DS70616G-page 153

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

NSTDIS OVAERR(1)OVBERR(1)COVAERR(1)COVBERR(1)OVATE(1)OVBTE(1)COVTE(1)

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0

SFTACERR(1)DIV0ERR DMACERR MATHERR ADDRERR STKERR OSCFAIL —

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 NSTDIS: Interrupt Nesting Disable bit

1 = Interrupt nesting is disabled

0 = Interrupt nesting is enabled

bit 14 OVAERR: Accumulator A Overflow Trap Flag bit(1)

1 = Trap was caused by overflow of Accumulator A

0 = Trap was not caused by overflow of Accumulator A

bit 13 OVBERR: Accumulator B Overflow Trap Flag bit(1)

1 = Trap was caused by overflow of Accumulator B

0 = Trap was not caused by overflow of Accumulator B

bit 12 COVAERR: Accumulator A Catastrophic Overflow Trap Flag bit(1)

1 = Trap was caused by catastrophic overflow of Accumulator A

0 = Trap was not caused by catastrophic overflow of Accumulator A

bit 11 COVBERR: Accumulator B Catastrophic Overflow Trap Flag bit(1)

1 = Trap was caused by catastrophic overflow of Accumulator B

0 = Trap was not caused by catastrophic overflow of Accumulator B

bit 10 OVATE: Accumulator A Overflow Trap Enable bit(1)

1 = Trap overflow of Accumulator A

0 = Trap is disabled

bit 9 OVBTE: Accumulator B Overflow Trap Enable bit(1)

1 = Trap overflow of Accumulator B

0 = Trap is disabled

bit 8 COVTE: Catastrophic Overflow Trap Enable bit(1)

1 = Trap on catastrophic overflow of Accumulator A or B is enabled

0 = Trap is disabled

bit 7 SFTACERR: Shift Accumulator Error Status bit(1)

1 = Math error trap was caused by an invalid accumulator shift

0 = Math error trap was not caused by an invalid accumulator shift

bit 6 DIV0ERR: Divide-by-Zero Error Status bit

1 = Math error trap was caused by a divide-by-zero

0 = Math error trap was not caused by a divide-by-zero

bit 5 DMACERR: DMAC Trap Flag bit

1 = DMAC trap has occurred

0 = DMAC trap has not occurred

Note 1: This bit is available on dsPIC33EPXXX(GP/MC/MU)806/810/814 devices only.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 154  2009-2012 Microchip Technology Inc.

bit 4 MATHERR: Math Error Status bit

1 = Math error trap has occurred

0 = Math error trap has not occurred

bit 3 ADDRERR: Address Error Trap Status bit

1 = Address error trap has occurred

0 = Address error trap has not occurred

bit 2 STKERR: Stack Error Trap Status bit

1 = Stack error trap has occurred

0 = Stack error trap has not occurred

bit 1 OSCFAIL: Oscillator Failure Trap Status bit

1 = Oscillator failure trap has occurred

0 = Oscillator failure trap has not occurred

bit 0 Unimplemented: Read as ‘0’

Note 1: This bit is available on dsPIC33EPXXX(GP/MC/MU)806/810/814 devices only.

 2009-2012 Microchip Technology Inc. DS70616G-page 155

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0

GIE DISI SWTRAP — — — — —

bit 15 bit 8

U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— — — INT4EP INT3EP INT2EP INT1EP INT0EP

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 GIE: Global Interrupt Enable bit

1 = Interrupts and associated IE bits are enabled

0 = Interrupts are disabled, but traps are still enabled

bit 14 DISI: DISI Instruction Status bit

1 = DISI instruction is active

0 = DISI instruction is not active

bit 13 SWTRAP: Software Trap Status bit

1 = Software trap is enabled

0 = Software trap is disabled

bit 12-5 Unimplemented: Read as ‘0’

bit 4 INT4EP: External Interrupt 4 Edge Detect Polarity Select bit

1 = Interrupt on negative edge

0 = Interrupt on positive edge

bit 3 INT3EP: External Interrupt 3 Edge Detect Polarity Select bit

1 = Interrupt on negative edge

0 = Interrupt on positive edge

bit 2 INT2EP: External Interrupt 2 Edge Detect Polarity Select bit

1 = Interrupt on negative edge

0 = Interrupt on positive edge

bit 1 INT1EP: External Interrupt 1 Edge Detect Polarity Select bit

1 = Interrupt on negative edge

0 = Interrupt on positive edge

bit 0 INT0EP: External Interrupt 0 Edge Detect Polarity Select bit

1 = Interrupt on negative edge

0 = Interrupt on positive edge

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 156  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 U-0

— UAE DAE DOOVR — — — —

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-7 Unimplemented: Read as ‘0’

bit 6 UAE: USB Address Error Soft Trap Status bit

1 = USB address error (soft) trap has occurred

0 = USB address error (soft) trap has not occurred

bit 5 DAE: DMA Address Error Soft Trap Status bit

1 = DMA address error soft trap has occurred

0 = DMA address error soft trap has not occurred

bit 4 DOOVR: Do Stack Overflow Soft Trap Status bit

1 = Do stack overflow soft trap has occurred

0 = Do stack overflow soft trap has not occurred

bit 3-0 Unimplemented: Read as ‘0’

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0

— — — — — — —SGHT

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-1 Unimplemented: Read as ‘0’

bit 0 SGHT: Software Generated Hard Trap Status bit

1 = Software generated hard trap has occurred

0 = Software generated hard trap has not occurred

 2009-2012 Microchip Technology Inc. DS70616G-page 157

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 R-0 R-0 R-0 R-0

— — — —ILR<3:0>

bit 15 bit 8

R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

VECNUM<7:0>(1)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 Unimplemented: Read as ‘0’

bit 11-8 ILR<3:0>: New CPU Interrupt Priority Level bits

1111 = CPU Interrupt Priority Level is 15

•

0001 = CPU Interrupt Priority Level is 1

0000 = CPU Interrupt Priority Level is 0

bit 7-0 VECNUM<7:0>: Vector Number of Pending Interrupt bits(1)

11111111 = 255, Reserved

•

00001001 = 9, IC1 – Input Capture 1

00001000 = 8, INT0 – External Interrupt 0

00000111 = 7, Reserved

00000110 = 6, Generic soft error trap

00000101 = 5, DMAC error trap

00000100 = 4, Math error trap

00000011 = 3, Stack error trap

00000010 = 2, Generic hard trap

00000001 = 1, Address error trap

00000000 = 0, Oscillator fail trap

Note 1: See Table 7-1 for the complete list of interrupt vector numbers.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 158  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 159

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

8.0 DIRECT MEMORY ACCESS

(DMA)

The DMA controller transfers data between

peripheral data registers and data space SRAM.

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 DMA subsystem uses

dual-ported SRAM memory (DPSRAM) and register

structures that allow the DMA to operate across its

own, independent address and data buses with no

impact on CPU operation. This architecture eliminates

the need for cycle stealing, which halts the CPU when

a higher priority DMA transfer is requested. Both the

CPU and DMA controller can write and read to/from

addresses within data space without interference, such

as CPU stalls, resulting in maximized, real-time

performance. Alternatively, DMA operation and data

transfer to/from the memory and peripherals are not

impacted by CPU processing. For example, when a

Run-Time Self-Programming (RTSP) operation is

performed, the CPU does not execute any instructions

until RTSP is finished. This condition, however, does

not impact data transfer to/from memory and the

peripherals.

In addition, DMA can access entire data memory space

(SRAM and DPSRAM). The Data Memory Bus Arbiter

is utilized when either the CPU or DMA attempts to

access non-dual ported SRAM, resulting in potential

DMA or CPU stalls.

The DMA controller supports up to 15 independent

channels. Each channel can be configured for transfers

to or from selected peripherals. Some of the

peripherals supported by the DMA controller include:

• ECAN™

• Data Converter Interface (DCI)

• Analog-to-Digital Converter (ADC)

• Serial Peripheral Interface (SPI)

•UART

• Input Capture

• Output Compare

• Parallel Master Port (PMP)

Refer to Tab l e 8 -1 for a complete list of supported

peripherals.

FIGURE 8-1: DMA CONTROLLER

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this

data sheet, refer to Section 22. “Direct

Memory Access (DMA)” (DS70348)

of the “dsPIC33E/PIC24E Family

Reference Manual”, which is available

from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

DMA

DPSRAM

PERIPHERAL

Arbiter

SRAM

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 160  2009-2012 Microchip Technology Inc.

In addition, DMA transfers can be triggered by timers

as well as external interrupts. Each DMA channel is

unidirectional. Two DMA channels must be allocated to

read and write to a peripheral. If more than one channel

receive a request to transfer data, a simple fixed priority

scheme, based on channel number, dictates which

channel completes the transfer and which channel, or

channels, are left pending. Each DMA channel moves

a block of data, after which it generates an interrupt to

the CPU to indicate that the block is available for

processing.

The DMA controller provides these functional

capabilities:

• Up to 15 DMA Channels

• Register Indirect With Post-Increment Addressing

mode

• Register Indirect Without Post-Increment

Addressing mode

• Peripheral Indirect Addressing mode (peripheral

generates destination address)

• CPU Interrupt after Half or Full Block Transfer

Complete

• Byte or Word Transfers

• Fixed Priority Channel Arbitration

• Manual (software) or Automatic (peripheral DMA

requests) Transfer Initiation

• One-Shot or Auto-Repeat Block Transfer modes

• Ping-Pong mode (automatic switch between two

DPSRAM start addresses after each block

transfer complete)

• DMA Request for Each Channel can be Selected

from Any Supported Interrupt Source

• Debug Support Features

The peripherals that can utilize DMA are listed in

Table 8-1.

TABLE 8-1: DMA CHANNEL TO PERIPHERAL ASSOCIATIONS

Peripheral to DMA Association DMAxREQ Register

IRQSEL<7:0> Bits

DMAxPAD Register

(Values to Read from

Peripheral)

DMAxPAD Register

(Values to Write to

Peripheral)

INT0 – External Interrupt 0 00000000 ——

IC1 – Input Capture 1 00000001 0x0144 (IC1BUF) —

IC2 – Input Capture 2 00000101 0x014C (IC2BUF) —

IC3 – Input Capture 3 00100101 0x0154 (IC3BUF) —

IC4 – Input Capture 4 00100110 0x015C (IC4BUF) —

OC1 – Output Compare 1 00000010 — 0x0906 (OC1R)

0x0904 (OC1RS)

OC2 – Output Compare 2 00000110 — 0x0910 (OC2R)

0x090E (OC2RS)

OC3 – Output Compare 3 00011001 — 0x091A (OC3R)

0x0918 (OC3RS)

OC4 – Output Compare 4 00011010 — 0x0924 (OC4R)

0x0922 (OC4RS)

TMR2 – Timer2 00000111 ——

TMR3 – Timer3 00001000 ——

TMR4 – Timer4 00011011 ——

TMR5 – Timer5 00011100 ——

SPI1 Transfer Done 00001010 0x0248 (SPI1BUF) 0x0248 (SPI1BUF)

SPI2 Transfer Done 00100001 0x0268 (SPI2BUF) 0x0268 (SPI2BUF)

SPI3 Transfer Done 01011011 0x02A8 (SPI3BUF) 0x02A8 (SPI3BUF)

SPI4 Transfer Done 01111011 0x02C8 (SPI4BUF) 0x02C8 (SPI4BUF)

UART1RX – UART1 Receiver 00001011 0x0226 (U1RXREG) —

UART1TX – UART1 Transmitter 00001100 — 0x0224 (U1TXREG)

UART2RX – UART2 Receiver 00011110 0x0236 (U2RXREG) —

UART2TX – UART2 Transmitter 00011111 — 0x0234 (U2TXREG)

UART3RX – UART3 Receiver 01010010 0x0256 (U3RXREG) —

UART3TX – UART3 Transmitter 01010011 — 0x0254 (U3TXREG)

 2009-2012 Microchip Technology Inc. DS70616G-page 161

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 8-2: DMA CONTROLLER TO PERIPHERAL ASSOCIATIONS BLOCK DIAGRAM

UART4RX – UART4 Receiver 01011000 0x02B6 (U4RXREG) —

UART4TX – UART4 Transmitter 01011001 — 0x02B4 (U4TXREG)

ECAN1 – RX Data Ready 00100010 0x0440 (C1RXD) —

ECAN1 – TX Data Request 01000110 — 0x0442 (C1TXD)

ECAN2 – RX Data Ready 00110111 0x0540 (C2RXD) —

ECAN2 – TX Data Request 01000111 — 0x0542 (C2TXD)

DCI – DCI Transfer Done 00111100 0x0290 (RXBUF0) 0x0298 (TXBUF0)

ADC1 – ADC1 Convert Done 00001101 0x0300 (ADC1BUF0) —

ADC2 – ADC2 Convert Done 00010101 0x0340 (ADC2BUF0) —

PMP – PMP Data Move 00101101 0x0608 (PMDIN1) 0x0608 (PMDIN1)

TABLE 8-1: DMA CHANNEL TO PERIPHERAL ASSOCIATIONS (CONTINUED)

Peripheral to DMA Association DMAxREQ Register

IRQSEL<7:0> Bits

DMAxPAD Register

(Values to Read from

Peripheral)

DMAxPAD Register

(Values to Write to

Peripheral)

CPU

Arbiter

DPSRAM Peripheral 1

DMA

Peripheral

Non-DMA

PORT 2PORT 1

Peripheral 2

DMA

Ready

Peripheral 3

DMA

Ready

DMA X-Bus

CPU

CPU CPU

Peripheral Indirect Address

Note: CPU and DMA address buses are not shown for clarity.

DMA

Control

DMA Controller

DMA

CPU Peripheral X-Bus

IRQ to DMA

and Interrupt

Controller

Modules

SRAM X-Bus

IRQ to DMA and

Interrupt Controller

Modules

IRQ to DMA and

Interrupt Controller

Modules

0123 N

SRAM

4··

Channels

DMA DMA

DMA

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 162  2009-2012 Microchip Technology Inc.

8.1 DMA Resources

Many useful resources related to DMA are provided on

the main product page of the Microchip web site for the

devices listed in this data sheet. This product page,

which can be accessed using this link, contains the

latest updates and additional information.

8.1.1 KEY RESOURCES

•Section 22. “Direct Memory Access (DMA)”

(DS70348) in the “dsPIC33E/PIC24E Family

Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

8.2 DMA Control Registers

Each DMAC Channel x (where x = 0 through 14)

contains the following registers:

• 16-Bit DMA Channel Control register (DMAxCON)

• 16-Bit DMA Channel IRQ Select register

(DMAxREQ)

• 32-Bit DMA RAM Primary Start Address register

(DMAxSTA)

• 32-Bit DMA RAM Secondary Start Address

• 16-Bit DMA Peripheral Address register (DMAxPAD)

• 14-Bit DMA Transfer Count register (DMAxCNT)

Additional status registers (DMAPWC, DMARQC,

DMAPPS, DMALCA and DSADR) are common to all

DMAC channels. These status registers provide infor-

mation on write and request collisions, as well as on

last address and channel access information.

The DMA Interrupt Flags (DMAxIF) are located in an

IFSx register in the interrupt controller. The

corresponding interrupt enable control bits (DMAxIE)

are located in an IECx register in the interrupt

controller, and the corresponding interrupt priority

control bits (DMAxIP) are located in an IPCx register in

the interrupt controller.

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

 2009-2012 Microchip Technology Inc. DS70616G-page 163

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 U-0

CHEN SIZE DIR HALF NULLW — — —

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 U-0 U-0 R/W-0 R/W-0

——AMODE<1:0>—— MODE<1:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 CHEN: Channel Enable bit

1 = Channel is enabled

0 = Channel is disabled

bit 14 SIZE: Data Transfer Size bit

1 = Byte

0 =Word

bit 13 DIR: Transfer Direction bit (source/destination bus select)

1 = Reads from DPSRAM (or RAM) address, writes to peripheral address

0 = Reads from peripheral address, writes to DPSRAM (or RAM) address

bit 12 HALF: Block Transfer Interrupt Select bit

1 = Initiates interrupt when half of the data has been moved

0 = Initiates interrupt when all of the data has been moved

bit 11 NULLW: Null Data Peripheral Write Mode Select bit

1 = Null data write to peripheral in addition to DPSRAM (or RAM) write (DIR bit must also be clear)

0 = Normal operation

bit 10-6 Unimplemented: Read as ‘0’

bit 5-4 AMODE<1:0>: DMA Channel Addressing Mode Select bits

11 = Reserved

10 = Peripheral Indirect Addressing mode

01 = Register Indirect without Post-Increment mode

00 = Register Indirect with Post-Increment mode

bit 3-2 Unimplemented: Read as ‘0’

bit 1-0 MODE<1:0>: DMA Channel Operating Mode Select bits

11 = One-Shot, Ping-Pong modes are enabled (one block transfer from/to each DMA buffer)

10 = Continuous, Ping-Pong modes are enabled

01 = One-Shot, Ping-Pong modes are disabled

00 = Continuous, Ping-Pong modes are disabled

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 164  2009-2012 Microchip Technology Inc.

R/S-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

FORCE(1)— — — — — — —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

IRQSEL<7:0>

bit 7 bit 0

Legend: S = Settable bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 FORCE: Force DMA Transfer bit(1)

1 = Forces a single DMA transfer (Manual mode)

0 = Automatic DMA transfer initiation by DMA request

bit 14-8 Unimplemented: Read as ‘0’

bit 7-0 IRQSEL<7:0>: DMA Peripheral IRQ Number Select bits

00000000 = INT0 – External Interrupt 0

00000001 = IC1 – Input Capture 1

00000010 = OC1 – Output Compare 1

00000101 = IC2 – Input Capture 2

00000110 = OC2 – Output Compare 2

00000111 = TMR2 – Timer2

00001000 = TMR3 – Timer3

00001010 = SPI1 – Transfer done

00001011 = UART1RX – UART1 Receiver

00001100 = UART1TX – UART1 Transmitter

00001101 = ADC1 – ADC1 convert done

00010101 = ADC2 – ADC2 convert done

00011001 = OC3 – Output Compare 3

00011010 = OC4 – Output Compare 4

00011011 = TMR4 – Timer4

00011100 = TMR5 – Timer5

00011110 = UART2RX – UART2 Receiver

00011111 = UART2TX – UART2 Transmitter

00100001 = SPI2 – Transfer done

00100010 = ECAN1 – RX data ready

00100101 = IC3 – Input Capture 3

00100110 = IC4 – Input Capture 4

00101101 = PMP Data mode

00110111 = ECAN2 – RX data ready

00111100 = DCI – DCI transfer done

01000110 = ECAN1 – TX data request

01000111 = ECAN2 – TX data request

01010010 = UART3RX – UART3 Receiver

01010011 = UART3TX – UART3 Transmitter

01011000 = UART4RX – UART4 Receiver

01011001 = UART4TX – UART4 Transmitter

01011011 = SPI3 – Transfer done

01111011 = SPI4 – Transfer done

Note 1: The FORCE bit cannot be cleared by user software. The FORCE bit is cleared by hardware when the

forced DMA transfer is complete or the channel is disabled (CHEN = 0).

 2009-2012 Microchip Technology Inc. DS70616G-page 165

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

STA<23:16>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7-0 STA<23:16>: Primary Start Address bits (source or destination)

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

STA<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

STA<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 STA<15:0>: Primary Start Address bits (source or destination)

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 166  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 R/W-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

STB<23:16>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7-0 STB<23:16>: Secondary Start Address bits (source or destination)

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

STB<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

STB<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 STB<15:0>: Secondary Start Address bits (source or destination)

 2009-2012 Microchip Technology Inc. DS70616G-page 167

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PAD<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PAD<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 PAD<15:0>: Peripheral Address Register bits

Note 1: If the channel is enabled (i.e., active), writes to this register may result in unpredictable behavior of the

DMA channel and should be avoided.

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— CNT<13:8>(2)

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

CNT<7:0>(2)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-0 CNT<13:0>: DMA Transfer Count Register bits(2)

Note 1: If the channel is enabled (i.e., active), writes to this register may result in unpredictable behavior of the

DMA channel and should be avoided.

2: The number of DMA transfers = CNT<13:0> + 1.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 168  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

DSADR<23:16>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7-0 DSADR<23:16>: Most Recent DMA Address Accessed by DMA bits

R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

DSADR<15:8>

bit 15 bit 8

R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

DSADR<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 DSADR<15:0>: Most Recent DMA Address Accessed by DMA bits

 2009-2012 Microchip Technology Inc. DS70616G-page 169

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

— PWCOL14 PWCOL13 PWCOL12 PWCOL11 PWCOL10 PWCOL9 PWCOL8

bit 15 bit 8

R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

PWCOL7 PWCOL6 PWCOL5 PWCOL4 PWCOL3 PWCOL2 PWCOL1 PWCOL0

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14 PWCOL14: Channel 14 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 13 PWCOL13: Channel 13 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 12 PWCOL12: Channel 12 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 11 PWCOL11: Channel 11 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 10 PWCOL10: Channel 10 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 9 PWCOL9: Channel 9 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 8 PWCOL8: Channel 8 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 7 PWCOL7: Channel 7 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 6 PWCOL6: Channel 6 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 5 PWCOL5: Channel 5 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 4 PWCOL4: Channel 4 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 3 PWCOL3: Channel 3 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 170  2009-2012 Microchip Technology Inc.

bit 2 PWCOL2: Channel 2 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 1 PWCOL1: Channel 1 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

bit 0 PWCOL0: Channel 0 Peripheral Write Collision Flag bit

1 = Write collision detected

0 = No write collision detected

 2009-2012 Microchip Technology Inc. DS70616G-page 171

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

— RQCOL14 RQCOL13 RQCOL12 RQCOL11 RQCOL10 RQCOL9 RQCOL8

bit 15 bit 8

R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

RQCOL7 RQCOL6 RQCOL5 RQCOL4 RQCOL3 RQCOL2 RQCOL1 RQCOL0

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14 RQCOL14: Channel 14 Transfer Request Collision Flag bit

1 = User FORCE and interrupt-based request collision detected

0 = No request collision detected

bit 13 RQCOL13: Channel 13 Transfer Request Collision Flag bit

1 = User FORCE and interrupt-based request collision detected

0 = No request collision detected

bit 12 RQCOL12: Channel 12 Transfer Request Collision Flag bit

1 = User FORCE and interrupt-based request collision detected

0 = No request collision detected

bit 11 RQCOL11: Channel 11 Transfer Request Collision Flag bit

1 = User FORCE and interrupt-based request collision detected

0 = No request collision detected

bit 10 RQCOL10: Channel 10 Transfer Request Collision Flag bit

1 = User FORCE and interrupt-based request collision detected

0 = No request collision detected

bit 9 RQCOL9: Channel 9 Transfer Request Collision Flag bit

1 = User FORCE and interrupt-based request collision detected

0 = No request collision detected

bit 8 RQCOL8: Channel 8 Transfer Request Collision Flag bit

1 = User FORCE and interrupt-based request collision detected

0 = No request collision detected

bit 7 RQCOL7: Channel 7 Transfer Request Collision Flag bit

1 = User FORCE and interrupt-based request collision detected

0 = No request collision detected

bit 6 RQCOL6: Channel 6 Transfer Request Collision Flag bit

1 = User FORCE and interrupt-based request collision detected

0 = No request collision detected

bit 5 RQCOL5: Channel 5 Transfer Request Collision Flag bit

1 = User FORCE and interrupt-based request collision detected

0 = No request collision detected

bit 4 RQCOL4: Channel 4 Transfer Request Collision Flag bit

1 = User FORCE and interrupt-based request collision detected

0 = No request collision detected

bit 3 RQCOL3: Channel 3 Transfer Request Collision Flag bit

1 = User FORCE and interrupt-based request collision detected

0 = No request collision detected

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 172  2009-2012 Microchip Technology Inc.

bit 2 RQCOL2: Channel 2 Transfer Request Collision Flag bit

1 = User FORCE and interrupt-based request collision detected

0 = No request collision detected

bit 1 RQCOL1: Channel 1 Transfer Request Collision Flag bit

1 = User FORCE and interrupt-based request collision detected

0 = No request collision detected

bit 0 RQCOL0: Channel 0 Transfer Request Collision Flag bit

1 = User FORCE and interrupt-based request collision detected

0 = No request collision detected

 2009-2012 Microchip Technology Inc. DS70616G-page 173

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 U-0 U-0 U-0 R-1 R-1 R-1 R-1

— — — — LSTCH<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-4 Unimplemented: Read as ‘0’

bit 3-0 LSTCH<3:0>: Last DMAC Channel Active Status bits

1111 = No DMA transfer has occurred since system Reset

1110 = Last data transfer was handled by Channel 14

1101 = Last data transfer was handled by Channel 13

1100 = Last data transfer was handled by Channel 12

1011 = Last data transfer was handled by Channel 11

1010 = Last data transfer was handled by Channel 10

1001 = Last data transfer was handled by Channel 9

1000 = Last data transfer was handled by Channel 8

0111 = Last data transfer was handled by Channel 7

0110 = Last data transfer was handled by Channel 6

0101 = Last data transfer was handled by Channel 5

0100 = Last data transfer was handled by Channel 4

0011 = Last data transfer was handled by Channel 3

0010 = Last data transfer was handled by Channel 2

0001 = Last data transfer was handled by Channel 1

0000 = Last data transfer was handled by Channel 0

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 174  2009-2012 Microchip Technology Inc.

U-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

— PPST14 PPST13 PPST12 PPST11 PPST10 PPST9 PPST8

bit 15 bit 8

R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

PPST7 PPST6 PPST5 PPST4 PPST3 PPST2 PPST1 PPST0

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14 PPST14: Channel 14 Ping-Pong Mode Status Flag bit

1 = DMASTB14 register selected

0 = DMASTA14 register selected

bit 13 PPST13: Channel 13 Ping-Pong Mode Status Flag bit

1 = DMASTB13 register selected

0 = DMASTA13 register selected

bit 12 PPST12: Channel 12 Ping-Pong Mode Status Flag bit

1 = DMASTB12 register selected

0 = DMASTA12 register selected

bit 11 PPST11: Channel 11 Ping-Pong Mode Status Flag bit

1 = DMASTB11 register selected

0 = DMASTA11 register selected

bit 10 PPST10: Channel 10 Ping-Pong Mode Status Flag bit

1 = DMASTB10 register selected

0 = DMASTA10 register selected

bit 9 PPST9: Channel 9 Ping-Pong Mode Status Flag bit

1 = DMASTB9 register selected

0 = DMASTA9 register selected

bit 8 PPST8: Channel 8 Ping-Pong Mode Status Flag bit

1 = DMASTB8 register selected

0 = DMASTA8 register selected

bit 7 PPST7: Channel 7 Ping-Pong Mode Status Flag bit

1 = DMASTB7 register selected

0 = DMASTA7 register selected

bit 6 PPST6: Channel 6 Ping-Pong Mode Status Flag bit

1 = DMASTB6 register selected

0 = DMASTA6 register selected

bit 5 PPST5: Channel 5 Ping-Pong Mode Status Flag bit

1 = DMASTB5 register selected

0 = DMASTA5 register selected

bit 4 PPST4: Channel 4 Ping-Pong Mode Status Flag bit

1 = DMASTB4 register selected

0 = DMASTA4 register selected

bit 3 PPST3: Channel 3 Ping-Pong Mode Status Flag bit

1 = DMASTB3 register selected

0 = DMASTA3 register selected

 2009-2012 Microchip Technology Inc. DS70616G-page 175

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

bit 2 PPST2: Channel 2 Ping-Pong Mode Status Flag bit

1 = DMASTB2 register selected

0 = DMASTA2 register selected

bit 1 PPST1: Channel 1 Ping-Pong Mode Status Flag bit

1 = DMASTB1 register selected

0 = DMASTA1 register selected

bit 0 PPST0: Channel 0 Ping-Pong Mode Status Flag bit

1 = DMASTB0 register selected

0 = DMASTA0 register selected

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 176  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 177

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

9.0 OSCILLATOR CONFIGURATION The oscillator system provides:

• Four external and internal oscillator options

• Auxiliary oscillator that provides clock source to

the USB module (if available)

• On-chip Phase-Locked Loop (PLL) to boost

internal operating frequency on select internal and

external oscillator sources

• On-the-fly clock switching between various clock

sources

• Doze mode for system power savings

• Fail-Safe Clock Monitor (FSCM) that detects clock

failure and permits safe application recovery or

shutdown

• Nonvolatile Configuration bits for clock source

selection

A simplified diagram of the oscillator system is shown

in Figure 9-1.

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this

data sheet, refer to Section 7. “Oscil-

lator” (DS70580) of the “dsPIC33E/

PIC24E Family Reference Manual”,

which is available from the Microchip web

site (www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 178  2009-2012 Microchip Technology Inc.

FIGURE 9-1: OSCILLATOR SYSTEM DIAGRAM

Note 1: See Figure 9-2 for PLL and FVCO details.

2: If the oscillator is used with XT or HS modes, an external parallel resistor with the value of 1 Mmust be connected.

3: See Figure 9-3 for APLL details.

Secondary Oscillator (SOSC)

LPOSCEN

SOSCO

SOSCI

Timer1

XTPLL, HSPLL,

XT, HS, EC

FRCDIV<2:0>

WDT, PWRT,

FRCDIVN

SOSC

FRCDIV16

ECPLL, FRCPLL

NOSC<2:0> FNOSC<2:0>

Reset

FRC

Oscillator

LPRC

Oscillator

DOZE<2:0>

S1/S3

FRC

LPRC S0

÷ 16

Clock Switch

Clock Fail

÷ 2

TUN<5:0>

PLL(1) FCY

FOSC

FRCDIV

DOZE

FSCM

ACLK

POSCCLK

Auxiliary Oscillator

SELACLK

USB

FVCO(1)

ENAPLL

ASRCSEL ENAPLL

APLL(3)

POSCCLK

FRCCLK

FVCO(1)

÷N

APLLPOST<2:0>

FRCCLK

FRCSEL

OSC2

OSC1

Primary Oscillator (POSC)

R(2)

POSCMD<1:0>

FAVCO

ROSEL RODIV<3:0>

REFCLKO

POSCCLK

RPn

FOSC

Reference Clock Generation

Auxiliary Clock Generation

(dsPIC33EPXXMU8XX and

PIC24EPXXXGU8XX Devices Only)

÷ N

 2009-2012 Microchip Technology Inc. DS70616G-page 179

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

9.1 CPU Clocking System

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 family of devices

provides seven system clock options:

• Fast RC (FRC) Oscillator

• FRC Oscillator with Phase-Locked Loop (PLL)

• Primary (XT, HS or EC) Oscillator

• Primary Oscillator with PLL

• Secondary (LP) Oscillator

• Low-Power RC (LPRC) Oscillator

• FRC Oscillator with postscaler

Instruction execution speed or device operating

frequency, FCY, is given by Equation 9-1.

EQUATION 9-1: DEVICE OPERATING

FREQUENCY

Figure 9-2 is a block diagram of the PLL module.

Equation 9-2 provides the relation between input

frequency (FIN) and output frequency (FOSC).

Equation 9-3 provides the relation between input

frequency (FIN) and VCO frequency (FVCO).

FIGURE 9-2: PLL BLOCK DIAGRAM

EQUATION 9-2: FOSC CALCULATION

EQUATION 9-3: FVCO CALCULATION

FCY = FOSC/2

÷ N1

÷ M

÷ N2

PFD VCO

PLLPRE<4:0>

PLLDIV<8:0>

PLLPOST<2:0>

0.8 MHz < FREF < 8.0 MHz

120 MHZ < FVCO < 340 MHZFOSC < 120 MHz @ +125ºC

FIN FREF FVCO FOSC

FOSC < 140 MHz @ +85ºC

FOSC FIN M

N1N2

---------------------





FIN PLLDIV 2+

PLLPRE 2+2PLLPOST 1+

----------------------------------------------------------------------------------------





==

Where,

N1 = PLLPRE + 2

N2 = 2 x (PLLPOST + 1)

M = PLLDIV + 2

FVCO FIN M

-------





FIN PLLDIV 2+

PLLPRE 2+

-------------------------------------





==

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 180  2009-2012 Microchip Technology Inc.

Figure 9-3 illustrates a block diagram of the auxiliary

PLL module.

FIGURE 9-3: APLL BLOCK DIAGRAM

Equation 9-4 shows the relationship between the

auxiliary PLL input clock frequency (FAIN) and the

AVCO frequency (FAVCO).

EQUATION 9-4: FAVCO CALCULATION

Note: The auxiliary PLL module is only avail-

able on dsPIC33EPXXXMU8XX and

PIC24EPXXXGU8XX devices.

÷ N1

÷ M

PFD VCO

APLLPRE<2:0>

APLLDIV

<2:0>

3 MHz < FAREF < 5.5 MHz

60 MHZ < FAVCO < 120 MHZ

FAIN FAREF FAVCO

FAVCO FAIN M

-------





=

 2009-2012 Microchip Technology Inc. DS70616G-page 181

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 9-1: CONFIGURATION BIT VALUES FOR CLOCK SELECTION

9.2 Oscillator Resources

Many useful resources related to the Oscillator are

provided on the main product page of the Microchip

web site for the devices listed in this data sheet. This

product page, which can be accessed using this link,

contains the latest updates and additional information.

9.2.1 KEY RESOURCES

•Section 7. “Oscillator” (DS70580) in the

“dsPIC33E/PIC24E Family Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

Oscillator Mode Oscillator

Source POSCMD<1:0> FNOSC<2:0> See

Notes

Fast RC Oscillator with Divide-by-N (FRCDIVN) Internal xx 111 1, 2

Fast RC Oscillator with Divide-by-16 (FRCDIV16) Internal xx 110 1

Low-Power RC Oscillator (LPRC) Internal xx 101 1

Secondary (Timer1) Oscillator (SOSC) Secondary xx 100 1

Primary Oscillator (HS) with PLL (HSPLL) Primary 10 011 —

Primary Oscillator (XT) with PLL (XTPLL) Primary 01 011 —

Primary Oscillator (EC) with PLL (ECPLL) Primary 00 011 1

Primary Oscillator (HS) Primary 10 010 —

Primary Oscillator (XT) Primary 01 010 —

Primary Oscillator (EC) Primary 00 010 1

Fast RC Oscillator (FRC) with Divide-by-N and PLL

(FRCPLL)

Internal xx 001 1

Fast RC Oscillator (FRC) Internal xx 000 1

Note 1: OSC2 pin function is determined by the OSCIOFNC Configuration bit.

2: This is the default oscillator mode for an unprogrammed (erased) device.

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 182  2009-2012 Microchip Technology Inc.

9.3 Oscillator Control Registers

U-0 R-0 R-0 R-0 U-0 R/W-y R/W-y R/W-y

— COSC<2:0> — NOSC<2:0>(2)

bit 15 bit 8

R/W-0 R/W-0 R-0 U-0 R/C-0 U-0 R/W-0 R/W-0

CLKLOCK IOLOCK LOCK —CF — LPOSCEN OSWEN

bit 7 bit 0

Legend: y = Value Set from Configuration bits on POR C = Clearable bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-12 COSC<2:0>: Current Oscillator Selection bits (read-only)

111 = Fast RC Oscillator (FRC) with Divide-by-N

110 = Fast RC Oscillator (FRC) with Divide-by-16

101 = Low-Power RC Oscillator (LPRC)

100 = Secondary Oscillator (SOSC)

011 = Primary Oscillator (XT, HS, EC) with PLL

010 = Primary Oscillator (XT, HS, EC)

001 = Fast RC Oscillator (FRC) with Divide-by-N and PLL

000 = Fast RC Oscillator (FRC)

bit 11 Unimplemented: Read as ‘0’

bit 10-8 NOSC<2:0>: New Oscillator Selection bits(2)

111 = Fast RC Oscillator (FRC) with Divide-by-N

110 = Fast RC Oscillator (FRC) with Divide-by-16

101 = Low-Power RC Oscillator (LPRC)

100 = Secondary Oscillator (SOSC)

011 = Primary Oscillator (XT, HS, EC) with PLL

010 = Primary Oscillator (XT, HS, EC)

001 = Fast RC Oscillator (FRC) with Divide-by-N and PLL

000 = Fast RC Oscillator (FRC)

bit 7 CLKLOCK: Clock Lock Enable bit

1 = If (FCKSM0 = 1), then clock and PLL configurations are locked

If (FCKSM0 = 0), then clock and PLL configurations may be modified

0 = Clock and PLL selections are not locked, configurations may be modified

bit 6 IOLOCK: I/O Lock Enable bit

1 = I/O lock is active

0 = I/O lock is not active

bit 5 LOCK: PLL Lock Status bit (read-only)

1 = Indicates that PLL is in lock or PLL start-up timer is satisfied

0 = Indicates that PLL is out of lock, start-up timer is in progress or PLL is disabled

bit 4 Unimplemented: Read as ‘0’

Note 1: Writes to this register require an unlock sequence. Refer to Section 7. “Oscillator” (DS70580) in the

“dsPIC33E/PIC24E Family Reference Manual” (available from the Microchip web site) for details.

2: Direct clock switches between any Primary Oscillator mode with PLL and FRCPLL mode are not permit-

ted. This applies to clock switches in either direction. In these instances, the application must switch to

FRC mode as a transition clock source between the two PLL modes.

3: This register resets only on a Power-on Reset (POR).

 2009-2012 Microchip Technology Inc. DS70616G-page 183

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

bit 3 CF: Clock Fail Detect bit (read/clear by application)

1 = FSCM has detected clock failure

0 = FSCM has not detected clock failure

bit 2 Unimplemented: Read as ‘0’

bit 1 LPOSCEN: Secondary (LP) Oscillator Enable bit

1 = Enables Secondary Oscillator

0 = Disables Secondary Oscillator

bit 0 OSWEN: Oscillator Switch Enable bit

1 = Requests oscillator switch to selection specified by NOSC<2:0> bits

0 = Oscillator switch is complete

Note 1: Writes to this register require an unlock sequence. Refer to Section 7. “Oscillator” (DS70580) in the

“dsPIC33E/PIC24E Family Reference Manual” (available from the Microchip web site) for details.

2: Direct clock switches between any Primary Oscillator mode with PLL and FRCPLL mode are not permit-

ted. This applies to clock switches in either direction. In these instances, the application must switch to

FRC mode as a transition clock source between the two PLL modes.

3: This register resets only on a Power-on Reset (POR).

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 184  2009-2012 Microchip Technology Inc.

R/W-0 R/W-0 R/W-1 R/W-1 R/W-0 R/W-0 R/W-0 R/W-0

ROI DOZE<2:0>(3)DOZEN(1,4)FRCDIV<2:0>

bit 15 bit 8

R/W-0 R/W-1 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PLLPOST<1:0> — PLLPRE<4:0>

bit 7 bit 0

Legend: y = Value set from Configuration bits on POR

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 ROI: Recover on Interrupt bit

1 = Interrupts will clear the DOZEN bit and the processor clock and peripheral clock ratio is set to 1:1

0 = Interrupts have no effect on the DOZEN bit

bit 14-12 DOZE<2:0>: Processor Clock Reduction Select bits(3)

111 = FCY divided by 128

110 = FCY divided by 64

101 = FCY divided by 32

100 = FCY divided by 16

011 = FCY divided by 8 (default)

010 = FCY divided by 4

001 = FCY divided by 2

000 = FCY divided by 1

bit 11 DOZEN: Doze Mode Enable bit(1,4)

1 = DOZE<2:0> field specifies the ratio between the peripheral clocks and the processor clocks

0 = Processor clock and peripheral clock ratio forced to 1:1

bit 10-8 FRCDIV<2:0>: Internal Fast RC Oscillator Postscaler bits

111 = FRC divided by 256

110 = FRC divided by 64

101 = FRC divided by 32

100 = FRC divided by 16

011 = FRC divided by 8

010 = FRC divided by 4

001 = FRC divided by 2

000 = FRC divided by 1 (default)

bit 7-6 PLLPOST<1:0>: PLL VCO Output Divider Select bits (also denoted as ‘N2’, PLL postscaler)

11 = Output divided by 8

10 = Reserved

01 = Output divided by 4 (default)

00 = Output divided by 2

bit 5 Unimplemented: Read as ‘0’

Note 1: This bit is cleared when the ROI bit is set and an interrupt occurs.

2: This register resets only on a Power-on Reset (POR).

3: DOZE<2:0> bits can only be written to when the DOZEN bit is clear. If DOZEN = 1, any writes to

DOZE<2:0> are ignored.

4: The DOZEN bit cannot be set if DOZE<2:0> = 000. If DOZE<2:0> = 000, any attempt by user software to

set the DOZEN bit is ignored.

 2009-2012 Microchip Technology Inc. DS70616G-page 185

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

bit 4-0 PLLPRE<4:0>: PLL Phase Detector Input Divider Select bits (also denoted as ‘N1’, PLL prescaler)

11111 = Input divided by 33

•

00001 = Input divided by 3

00000 = Input divided by 2 (default)

Note 1: This bit is cleared when the ROI bit is set and an interrupt occurs.

2: This register resets only on a Power-on Reset (POR).

3: DOZE<2:0> bits can only be written to when the DOZEN bit is clear. If DOZEN = 1, any writes to

DOZE<2:0> are ignored.

4: The DOZEN bit cannot be set if DOZE<2:0> = 000. If DOZE<2:0> = 000, any attempt by user software to

set the DOZEN bit is ignored.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 186  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0

— — — — — — —PLLDIV<8>

bit 15 bit 8

R/W-0 R/W-0 R/W-1 R/W-1 R/W-0 R/W-0 R/W-0 R/W-0

PLLDIV<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-9 Unimplemented: Read as ‘0’

bit 8-0 PLLDIV<8:0>: PLL Feedback Divisor bits (also denoted as ‘M’, PLL multiplier)

111111111 = 513

•

000110000 = 50 (default)

•

000000010 = 4

000000001 = 3

000000000 = 2

Note 1: This register is reset only on a Power-on Reset (POR).

 2009-2012 Microchip Technology Inc. DS70616G-page 187

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— TUN<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-6 Unimplemented: Read as ‘0’

bit 5-0 TUN<5:0>: FRC Oscillator Tuning bits

011111 = Center frequency + 11.625% (8.23 MHz)

011110 = Center frequency + 11.25% (8.20 MHz)

•

000001 = Center frequency + 0.375% (7.40 MHz)

000000 = Center frequency (7.37 MHz nominal)

111111 = Center frequency – 0.375% (7.345 MHz)

•

100001 = Center frequency – 11.625% (6.52 MHz)

100000 = Center frequency – 12% (6.49 MHz)

Note 1: This register resets only on a Power-on Reset (POR).

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 188  2009-2012 Microchip Technology Inc.

R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0

ENAPLL — SELACLK AOSCMD<1:0> ASRCSEL FRCSEL —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0

APLLPOST<2:0> —— APLLPRE<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 ENAPLL: Enable Auxiliary PLL (APLL) and Select APLL as USB Clock Source bit

1 = APLL is enabled, the USB clock source is the APLL output

0 = APLL is disabled, the USB clock source is the input clock to the APLL

bit 14 Unimplemented: Read as ‘0’

bit 13 SELACLK: Select Auxiliary Clock Source for Auxiliary Clock Divider bit

1 = Auxiliary PLL or oscillator provides the source clock for auxiliary clock divider

0 = Primary PLL provides the source clock for auxiliary clock divider

bit 12-11 AOSCMD<1:0>: Auxiliary Oscillator Mode bits

11 = EC (External Clock) Oscillator mode select

10 = XT (Crystal) Oscillator mode select

01 = HS (High-Speed) Oscillator mode select

00 = Auxiliary Oscillator disabled (default)

bit 10 ASRCSEL: Select Reference Clock Source for APLL bit

1 = Primary Oscillator is the clock source for APLL

0 = Auxiliary Oscillator is the clock source for APLL

bit 9 FRCSEL: Select FRC as Reference Clock Source for APLL bit

1 = FRC is the clock source for APLL

0 = Auxiliary Oscillator or Primary Oscillator is the clock source for APLL (determined by ASRCSEL bit)

bit 8 Unimplemented: Read as ‘0’

bit 7-5 APLLPOST<2:0>: Select PLL VCO Output Divider bits

111 = Divided by 1

110 = Divided by 2

101 = Divided by 4

100 = Divided by 8

011 = Divided by 16

010 = Divided by 32

001 = Divided by 64

000 = Divided by 256 (default)

bit 4-3 Unimplemented: Read as ‘0’

bit 2-0 APLLPRE<2:0>: PLL Phase Detector Input Divider bits

111 = Divided by 12

110 = Divided by 10

101 = Divided by 6

100 = Divided by 5

011 = Divided by 4

010 = Divided by 3

001 = Divided by 2

000 = Divided by 1 (default)

Note 1: This register resets only on a Power-on Reset (POR).

2: This register is only available on dsPIC33EPXXXMU8XX and PIC24EPXXXGU8XX devices.

 2009-2012 Microchip Technology Inc. DS70616G-page 189

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0

— — — — — APLLDIV<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-3 Unimplemented: Read as ‘0’

bit 2-0 APLLDIV<2:0>: PLL Feedback Divisor bits (PLL Multiplier Ratio)

111 = 24

110 = 21

101 = 20

100 = 19

011 = 18

010 = 17

001 = 16

000 = 15 (default)

Note 1: This register resets only on a Power-on Reset (POR).

2: This register is only available on dsPIC33EPXXXMU8XX and PIC24EPXXXGU8XX devices.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 190  2009-2012 Microchip Technology Inc.

R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

ROON — ROSSLP ROSEL RODIV<3:0>(1)

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 ROON: Reference Oscillator Output Enable bit

1 = Reference oscillator output is enabled on REFCLK pin(2)

0 = Reference oscillator output is disabled

bit 14 Unimplemented: Read as ‘0’

bit 13 ROSSLP: Reference Oscillator Run in Sleep bit

1 = Reference oscillator output continues to run in Sleep

0 = Reference oscillator output is disabled in Sleep

bit 12 ROSEL: Reference Oscillator Source Select bit

1 = Oscillator crystal used as the reference clock

0 = System clock used as the reference clock

bit 11-8 RODIV<3:0>: Reference Oscillator Divider bits(1)

1111 = Reference clock divided by 32,768

1110 = Reference clock divided by 16,384

1101 = Reference clock divided by 8,192

1100 = Reference clock divided by 4,096

1011 = Reference clock divided by 2,048

1010 = Reference clock divided by 1,024

1001 = Reference clock divided by 512

1000 = Reference clock divided by 256

0111 = Reference clock divided by 128

0110 = Reference clock divided by 64

0101 = Reference clock divided by 32

0100 = Reference clock divided by 16

0011 = Reference clock divided by 8

0010 = Reference clock divided by 4

0001 = Reference clock divided by 2

0000 = Reference clock

bit 7-0 Unimplemented: Read as ‘0’

Note 1: The reference oscillator output must be disabled (ROON = 0) before writing to these bits.

2: This pin is remappable. See Section 11.4 “Peripheral Pin Select” for more information.

 2009-2012 Microchip Technology Inc. DS70616G-page 191

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

10.0 POWER-SAVING FEATURES

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices provide the

ability to manage power consumption by selectively

managing clocking to the CPU and the peripherals.

In general, a lower clock frequency and a reduction

in the number of circuits being clocked constitutes

lower consumed power.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices can

manage power consumption in four ways:

• Clock frequency

• Instruction-based Sleep and Idle modes

• Software-controlled Doze mode

• Selective peripheral control in software

Combinations of these methods can be used to selec-

tively tailor an application’s power consumption while

still maintaining critical application features, such as

timing-sensitive communications.

10.1 Clock Frequency and Clock

Switching

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices allow a wide

range of clock frequencies to be selected under

application control. If the system clock configuration is

not locked, users can choose low-power or high-

precision oscillators by simply changing the NOSCx

bits (OSCCON<10:8>). The process of changing a

system clock during operation, as well as limitations to

the process, are discussed in more detail in

Section 9.0 “Oscillator Configuration”.

10.2 Instruction-Based Power-Saving

Modes

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices have two

special power-saving modes that are entered

through the execution of a special PWRSAV

instruction. Sleep mode stops clock operation and

halts all code execution. Idle mode halts the CPU

and code execution, but allows peripheral modules

to continue operation. The assembler syntax of the

PWRSAV instruction is shown in Example 10-1.

Sleep and Idle modes can be exited as a result of an

enabled interrupt, WDT time-out or a device Reset. When

the device exits these modes, it is said to wake up.

10.2.1 SLEEP MODE

The following occur in Sleep mode:

• The system clock source is shut down. If an

on-chip oscillator is used, it is turned off.

• The device current consumption is reduced to a

minimum, provided that no I/O pin is sourcing

current.

• The Fail-Safe Clock Monitor does not operate,

since the system clock source is disabled.

• The LPRC clock continues to run in Sleep mode if

the WDT is enabled.

• The WDT, if enabled, is automatically cleared

prior to entering Sleep mode.

• Some device features or peripherals can continue

to operate. This includes items such as the input

change notification on the I/O ports, or peripherals

that use an external clock input.

• Any peripheral that requires the system clock

source for its operation is disabled.

The device wakes up from Sleep mode on any of the

these events:

• Any interrupt source that is individually enabled

• Any form of device Reset

• A WDT time-out

On wake-up from Sleep mode, the processor restarts

with the same clock source that was active when Sleep

mode was entered.

EXAMPLE 10-1: PWRSAV INSTRUCTION SYNTAX

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this

data sheet, refer to Section 9. “Watch-

dog Timer and Power-Saving Modes”

(DS70615) of the “dsPIC33E/PIC24E

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Note: SLEEP_MODE and IDLE_MODE are con-

stants defined in the assembler include

file for the selected device.

PWRSAV #SLEEP_MODE ; Put the device into SLEEP mode

PWRSAV #IDLE_MODE ; Put the device into IDLE mode

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 192  2009-2012 Microchip Technology Inc.

10.2.2 IDLE MODE

The following occur in Idle mode:

• The CPU stops executing instructions.

• The WDT is automatically cleared.

• The system clock source remains active. By

default, all peripheral modules continue to operate

normally from the system clock source, but can

also be selectively disabled (see Section 10.4

“Peripheral Module Disable”).

• If the WDT or FSCM is enabled, the LPRC also

remains active.

The device wakes from Idle mode on any of these

events:

• Any interrupt that is individually enabled

• Any device Reset

• A WDT time-out

On wake-up from Idle mode, the clock is reapplied to

the CPU and instruction execution will begin (2-4 clock

cycles later), starting with the instruction following the

PWRSAV instruction, or the first instruction in the ISR.

10.2.3 INTERRUPTS COINCIDENT WITH

POWER SAVE INSTRUCTIONS

Any interrupt that coincides with the execution of a

PWRSAV instruction is held off until entry into Sleep or

Idle mode has completed. The device then wakes up

from Sleep or Idle mode.

10.3 Doze Mode

The preferred strategies for reducing power

consumption are changing clock speed and invoking

one of the power-saving modes. In some

circumstances, this cannot be practical. For example, it

may be necessary for an application to maintain

uninterrupted synchronous communication, even while

it is doing nothing else. Reducing system clock speed

can introduce communication errors, while using a

power-saving mode can stop communications

completely.

Doze mode is a simple and effective alternative method

to reduce power consumption while the device is still

executing code. In this mode, the system clock

continues to operate from the same source and at the

same speed. Peripheral modules continue to be

clocked at the same speed, while the CPU clock speed

is reduced. Synchronization between the two clock

domains is maintained, allowing the peripherals to

access the SFRs while the CPU executes code at a

slower rate.

Doze mode is enabled by setting the DOZEN bit

(CLKDIV<11>). The ratio between peripheral and core

clock speed is determined by the DOZE<2:0> bits

(CLKDIV<14:12>). There are eight possible configu-

rations, from 1:1 to 1:128, with 1:1 being the default

setting.

Programs can use Doze mode to selectively reduce

power consumption in event-driven applications. This

allows clock-sensitive functions, such as synchronous

communications, to continue without interruption while

the CPU idles, waiting for something to invoke an

interrupt routine. An automatic return to full-speed CPU

operation on interrupts can be enabled by setting the

ROI bit (CLKDIV<15>). By default, interrupt events

have no effect on Doze mode operation.

For example, suppose the device is operating at

20 MIPS and the ECAN module has been configured

for 500 kbps based on this device operating speed. If

the device is placed in Doze mode with a clock

frequency ratio of 1:4, the ECAN module continues to

communicate at the required bit rate of 500 kbps, but

the CPU now starts executing instructions at a

frequency of 5 MIPS.

10.4 Peripheral Module Disable

The Peripheral Module Disable (PMD) registers

provide a method to disable a peripheral module by

stopping all clock sources supplied to that module.

When a peripheral is disabled using the appropriate

PMD control bit, the peripheral is in a minimum power

consumption state. The control and status registers

associated with the peripheral are also disabled, so

writes to those registers do not have effect and read

values are invalid.

A peripheral module is enabled only if both the

associated bit in the PMD register is cleared and the

peripheral is supported by the specific dsPIC® DSC

variant. If the peripheral is present in the device, it is

enabled in the PMD register by default.

Note: If a PMD bit is set, the corresponding

module is disabled after a delay of one

instruction cycle. Similarly, if a PMD bit is

cleared, the corresponding module is

enabled after a delay of one instruction

cycle (assuming the module control regis-

ters are already configured to enable

module operation).

 2009-2012 Microchip Technology Inc. DS70616G-page 193

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

10.5 Power-Saving Resources

Many useful resources related to Power-Saving

features are provided on the main product page of the

Microchip web site for the devices listed in this data

sheet. This product page, which can be accessed using

this link, contains the latest updates and additional

information.

10.5.1 KEY RESOURCES

•Section 9. “Watchdog Timer and

Power-Saving Modes” (DS70615) in the

“dsPIC33E/PIC24E Family Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

10.6 Special Function Registers

Seven registers, PMD1: Peripheral Module Disable

Control Register 1 through PMD7: Peripheral Module

Disable Control Register 7, are provided for peripheral

module control.

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 194  2009-2012 Microchip Technology Inc.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

T5MD T4MD T3MD T2MD T1MD QEI1MD(1)PWMMD(1)DCIMD

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

I2C1MD U2MD U1MD SPI2MD SPI1MD C2MD C1MD AD1MD

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 T5MD: Timer5 Module Disable bit

1 = Timer5 module is disabled

0 = Timer5 module is enabled

bit 14 T4MD: Timer4 Module Disable bit

1 = Timer4 module is disabled

0 = Timer4 module is enabled

bit 13 T3MD: Timer3 Module Disable bit

1 = Timer3 module is disabled

0 = Timer3 module is enabled

bit 12 T2MD: Timer2 Module Disable bit

1 = Timer2 module is disabled

0 = Timer2 module is enabled

bit 11 T1MD: Timer1 Module Disable bit

1 = Timer1 module is disabled

0 = Timer1 module is enabled

bit 10 QEI1MD: QEI1 Module Disable bit(1)

1 = QEI1 module is disabled

0 = QEI1 module is enabled

bit 9 PWMMD: PWM Module Disable bit(1)

1 = PWM module is disabled

0 = PWM module is enabled

bit 8 DCIMD: DCI Module Disable bit

1 = DCI module is disabled

0 = DCI module is enabled

bit 7 I2C1MD: I2C1 Module Disable bit

1 = I2C1 module is disabled

0 = I2C1 module is enabled

bit 6 U2MD: UART2 Module Disable bit

1 = UART2 module is disabled

0 = UART2 module is enabled

bit 5 U1MD: UART1 Module Disable bit

1 = UART1 module is disabled

0 = UART1 module is enabled

bit 4 SPI2MD: SPI2 Module Disable bit

1 = SPI2 module is disabled

0 = SPI2 module is enabled

Note 1: This bit is available on dsPIC33EPXXX(MC/MU)806/810/814 devices only.

 2009-2012 Microchip Technology Inc. DS70616G-page 195

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

bit 3 SPI1MD: SPI1 Module Disable bit

1 = SPI1 module is disabled

0 = SPI1 module is enabled

bit 2 C2MD: ECAN2 Module Disable bit

1 = ECAN2 module is disabled

0 = ECAN2 module is enabled

bit 1 C1MD: ECAN1 Module Disable bit

1 = ECAN1 module is disabled

0 = ECAN1 module is enabled

bit 0 AD1MD: ADC1 Module Disable bit

1 = ADC1 module is disabled

0 = ADC1 module is enabled

Note 1: This bit is available on dsPIC33EPXXX(MC/MU)806/810/814 devices only.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 196  2009-2012 Microchip Technology Inc.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

IC8MD IC7MD IC6MD IC5MD IC4MD IC3MD IC2MD IC1MD

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

OC8MD OC7MD OC6MD OC5MD OC4MD OC3MD OC2MD OC1MD

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 IC8MD: Input Capture 8 Module Disable bit

1 = Input Capture 8 module is disabled

0 = Input Capture 8 module is enabled

bit 14 IC7MD: Input Capture 2 Module Disable bit

1 = Input Capture 7 module is disabled

0 = Input Capture 7 module is enabled

bit 13 IC6MD: Input Capture 6 Module Disable bit

1 = Input Capture 6 module is disabled

0 = Input Capture 6 module is enabled

bit 12 IC5MD: Input Capture 5 Module Disable bit

1 = Input Capture 5 module is disabled

0 = Input Capture 5 module is enabled

bit 11 IC4MD: Input Capture 4 Module Disable bit

1 = Input Capture 4 module is disabled

0 = Input Capture 4 module is enabled

bit 10 IC3MD: Input Capture 3 Module Disable bit

1 = Input Capture 3 module is disabled

0 = Input Capture 3 module is enabled

bit 9 IC2MD: Input Capture 2 Module Disable bit

1 = Input Capture 2 module is disabled

0 = Input Capture 2 module is enabled

bit 8 IC1MD: Input Capture 1 Module Disable bit

1 = Input Capture 1 module is disabled

0 = Input Capture 1 module is enabled

bit 7 OC8MD: Output Compare 8 Module Disable bit

1 = Output Compare 8 module is disabled

0 = Output Compare 8 module is enabled

bit 6 OC7MD: Output Compare 7 Module Disable bit

1 = Output Compare 7 module is disabled

0 = Output Compare 7 module is enabled

bit 5 OC6MD: Output Compare 6 Module Disable bit

1 = Output Compare 6 module is disabled

0 = Output Compare 6 module is enabled

bit 4 OC5MD: Output Compare 5 Module Disable bit

1 = Output Compare 5 module is disabled

0 = Output Compare 5 module is enabled

 2009-2012 Microchip Technology Inc. DS70616G-page 197

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

bit 3 OC4MD: Output Compare 4 Module Disable bit

1 = Output Compare 4 module is disabled

0 = Output Compare 4 module is enabled

bit 2 OC3MD: Output Compare 3 Module Disable bit

1 = Output Compare 3 module is disabled

0 = Output Compare 3 module is enabled

bit 1 OC2MD: Output Compare 2 Module Disable bit

1 = Output Compare 2 module is disabled

0 = Output Compare 2 module is enabled

bit 0 OC1MD: Output Compare 1 Module Disable bit

1 = Output Compare 1 module is disabled

0 = Output Compare 1 module is enabled

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 198  2009-2012 Microchip Technology Inc.

R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0

T9MD T8MD T7MD T6MD — CMPMD RTCCMD PMPMD

bit 15 bit 8

R/W-0 U-0 R/W-0 U-0 R/W-0 U-0 R/W-0 R/W-0

CRCMD —QEI2MD

(1)—U3MD— I2C2MD AD2MD

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 T9MD: Timer9 Module Disable bit

1 = Timer9 module is disabled

0 = Timer9 module is enabled

bit 14 T8MD: Timer8 Module Disable bit

1 = Timer8 module is disabled

0 = Timer8 module is enabled

bit 13 T7MD: Timer7 Module Disable bit

1 = Timer7 module is disabled

0 = Timer7 module is enabled

bit 12 T6MD: Timer6 Module Disable bit

1 = Timer6 module is disabled

0 = Timer6 module is enabled

bit 11 Unimplemented: Read as ‘0’

bit 10 CMPMD: Comparator Module Disable bit

1 = Comparator module is disabled

0 = Comparator module is enabled

bit 9 RTCCMD: RTCC Module Disable bit

1 = RTCC module is disabled

0 = RTCC module is enabled

bit 8 PMPMD: PMP Module Disable bit

1 = PMP module is disabled

0 = PMP module is enabled

bit 7 CRCMD: CRC Module Disable bit

1 = CRC module is disabled

0 = CRC module is enabled

bit 6 Unimplemented: Read as ‘0’

bit 5 QEI2MD: QEI2 Module Disable bit(1)

1 = QEI2 module is disabled

0 = QEI2 module is enabled

bit 4 Unimplemented: Read as ‘0’

bit 3 U3MD: UART3 Module Disable bit

1 = UART3 module is disabled

0 = UART3 module is enabled

bit 2 Unimplemented: Read as ‘0’

Note 1: This bit is available in dsPIC33EPXXX(MC/MU)806/810/814 devices only.

 2009-2012 Microchip Technology Inc. DS70616G-page 199

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

bit 1 I2C2MD: I2C2 Module Disable bit

1 = I2C2 module is disabled

0 = I2C2 module is enabled

bit 0 AD2MD: ADC2 Module Disable bit

1 = ADC2 module is disabled

0 = ADC2 module is enabled

Note 1: This bit is available in dsPIC33EPXXX(MC/MU)806/810/814 devices only.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 200  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

————————

bit 15 bit 8

U-0 U-0 R/W-0 U-0 R/W-0 U-0 U-0 R/W-0

——U4MD—REFOMD—— USB1MD(1)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-6 Unimplemented: Read as ‘0’

bit 5 U4MD: UART4 Module Disable bit

1 = UART4 module is disabled

0 = UART4 module is enabled

bit 4 Unimplemented: Read as ‘0’

bit 3 REFOMD: Reference Clock Module Disable bit

1 = Reference clock module is disabled

0 = Reference clock module is enabled

bit 2-1 Unimplemented: Read as ‘0’

bit 0 USB1MD: USB Module Disable bit(1)

1 = USB module is disabled

0 = USB module is enabled

Note 1: This bit is only available on dsPIC33EPXXXMU8XXX and PIC24EPXXXGU8XX devices.

 2009-2012 Microchip Technology Inc. DS70616G-page 201

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

IC16MD IC15MD IC14MD IC13MD IC12MD IC11MD IC10MD IC9MD

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

OC16MD OC15MD OC14MD OC13MD OC12MD OC11MD OC10MD OC9MD

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 IC16MD: IC16 Module Disable bit

1 = IC16 module is disabled

0 = IC16 module is enabled

bit 14 IC15MD: IC15 Module Disable bit

1 = IC15 module is disabled

0 = IC15 module is enabled

bit 13 IC14MD: IC14 Module Disable bit

1 = IC14 module is disabled

0 = IC14 module is enabled

bit 12 IC13MD: IC13 Module Disable bit

1 = IC13 module is disabled

0 = IC13 module is enabled

bit 11 IC12MD: IC12 Module Disable bit

1 = IC12 module is disabled

0 = IC12 module is enabled

bit 10 IC11MD: IC11 Module Disable bit

1 = IC11 module is disabled

0 = IC11 module is enabled

bit 9 IC10MD: IC10 Module Disable bit

1 = IC10 module is disabled

0 = IC10 module is enabled

bit 8 IC9MD: IC9 Module Disable bit

1 = IC9 module is disabled

0 = IC9 module is enabled

bit 7 OC16MD: OC16 Module Disable bit

1 = OC16 module is disabled

0 = OC16 module is enabled

bit 6 OC15MD: OC15 Module Disable bit

1 = OC15 module is disabled

0 = OC15 module is enabled

bit 5 OC14MD: OC14 Module Disable bit

1 = OC14 module is disabled

0 = OC14 module is enabled

bit 4 OC13MD: OC13 Module Disable bit

1 = OC13 module is disabled

0 = OC13 module is enabled

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 202  2009-2012 Microchip Technology Inc.

bit 3 OC12MD: OC12 Module Disable bit

1 = OC12 module is disabled

0 = OC12 module is enabled

bit 2 OC11MD: OC11 Module Disable bit

1 = OC11 module is disabled

0 = OC11 module is enabled

bit 1 OC10MD: OC10 Module Disable bit

1 = OC10 module is disabled

0 = OC10 module is enabled

bit 0 OC9MD: OC9 Module Disable bit

1 = OC9 module is disabled

0 = OC9 module is enabled

 2009-2012 Microchip Technology Inc. DS70616G-page 203

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—PWM7MD

(1)PWM6MD(1)PWM5MD(1)PWM4MD(1)PWM3MD(1)PWM2MD(1)PWM1MD(1)

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0

—————— SPI4MD SPI3MD

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14 PWM7MD: PWM7 Module Disable bit(1)

1 = PWM7 module is disabled

0 = PWM7 module is enabled

bit 13 PWM6MD: PWM6 Module Disable bit(1)

1 = PWM6 module is disabled

0 = PWM6 module is enabled

bit 12 PWM5MD: PWM5 Module Disable bit(1)

1 = PWM5 module is disabled

0 = PWM5 module is enabled

bit 11 PWM4MD: PWM4 Module Disable bit(1)

1 = PWM4 module is disabled

0 = PWM4 module is enabled

bit 10 PWM3MD: PWM3 Module Disable bit(1)

1 = PWM3 module is disabled

0 = PWM3 module is enabled

bit 9 PWM2MD: PWM2 Module Disable bit(1)

1 = PWM2 module is disabled

0 = PWM2 module is enabled

bit 8 PWM1MD: PWM1 Module Disable bit(1)

1 = PWM1 module is disabled

0 = PWM1 module is enabled

bit 7-2 Unimplemented: Read as ‘0’

bit 1 SPI4MD: SPI4 Module Disable bit

1 = SPI4 module is disabled

0 = SPI4 module is enabled

bit 0 SPI3MD: SPI3 Module Disable bit

1 = SPI3 module is disabled

0 = SPI3 module is enabled

Note 1: This bit is available in dsPIC33EPXXX(MC/MU)806/810/814 devices only.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 204  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

————————

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 U-0

DMA12MD DMA8MD DMA4MD DMA0MD

————

DMA13MD DMA9MD DMA5MD DMA1MD

DMA14MD DMA10MD DMA6MD DMA2MD

— DMA11MD DMA7MD DMA3MD

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 DMA12MD: DMA12 Module Disable bit

1 = DMA12 module is disabled

0 = DMA12 module is enabled

DMA13MD: DMA13 Module Disable bit

1 = DMA13 module is disabled

0 = DMA13 module is enabled

DMA14MD: DMA14 Module Disable bit

1 = DMA14 module is disabled

0 = DMA14 module is enabled

bit 6 DMA8MD: DMA3 Module Disable bit

1 = DMA8 module is disabled

0 = DMA8 module is enabled

DMA9MD: DMA2 Module Disable bit

1 = DMA9 module is disabled

0 = DMA9 module is enabled

DMA10MD: DMA10 Module Disable bit

1 = DMA10 module is disabled

0 = DMA10 module is enabled

DMA11MD: DMA11 Module Disable bit

1 = DMA11 module is disabled

0 = DMA11 module is enabled

bit 5 DMA4MD: DMA4 Module Disable bit

1 = DMA4 module is disabled

0 = DMA4 module is enabled

DMA5MD: DMA5 Module Disable bit

1 = DMA5 module is disabled

0 = DMA5 module is enabled

DMA6MD: DMA6 Module Disable bit

1 = DMA6 module is disabled

0 = DMA6 module is enabled

DMA7MD: DMA7 Module Disable bit

1 = DMA7 module is disabled

0 = DMA7 module is enabled

 2009-2012 Microchip Technology Inc. DS70616G-page 205

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

bit 4 DMA0MD: DMA0 Module Disable bit

1 = DMA0 module is disabled

0 = DMA0 module is enabled

DMA1MD: DMA1 Module Disable bit

1 = DMA1 module is disabled

0 = DMA1 module is enabled

DMA2MD: DMA2 Module Disable bit

1 = DMA2 module is disabled

0 = DMA2 module is enabled

DMA3MD: DMA3 Module Disable bit

1 = DMA3 module is disabled

0 = DMA3 module is enabled

bit 3-0 Unimplemented: Read as ‘0’

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 206  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 207

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

11.0 I/O PORTS

All of the device pins (except VDD, VSS, MCLR and

OSC1/CLKI) are shared among the peripherals and the

parallel I/O ports. All I/O input ports feature Schmitt

Trigger inputs for improved noise immunity.

11.1 Parallel I/O (PIO) Ports

Generally, a parallel I/O port that shares a pin with a

peripheral is subservient to the peripheral. The

peripheral’s output buffer data and control signals are

provided to a pair of multiplexers. The multiplexers

select whether the peripheral or the associated port

has ownership of the output data and control signals of

the I/O pin. The logic also prevents “loop through,” in

which a port’s digital output can drive the input of a

peripheral that shares the same pin. Figure 11-1 illus-

trates how ports are shared with other peripherals and

the associated I/O pin to which they are connected.

When a peripheral is enabled and the peripheral is

actively driving an associated pin, the use of the pin as

a general purpose output pin is disabled. The I/O pin

can be read, but the output driver for the parallel port bit

is disabled. If a peripheral is enabled, but the peripheral

is not actively driving a pin, that pin can be driven by a

port.

All port pins have eight registers directly associated

with their operation as digital I/O. The Data Direction

or an output. If the data direction bit is a ‘1’, then the pin

is an input. All port pins are defined as inputs after a

Reset. Reads from the latch (LATx) read the latch.

Writes to the latch write the latch. Reads from the port

(PORTx) read the port pins, while writes to the port pins

write the latch.

Any bit and its associated data and control registers

that are not valid for a particular device is disabled. This

means the corresponding LATx and TRISx registers

and the port pin are read as zeros.

When a pin is shared with another peripheral or

function that is defined as an input only, it is

nevertheless regarded as a dedicated port because

there is no other competing source of outputs.

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this

data sheet, refer to Section 10. “I/O

Ports” (DS70598) of the “dsPIC33E/

PIC24E Family Reference Manual”,

which is available from the Microchip web

site (www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 208  2009-2012 Microchip Technology Inc.

FIGURE 11-1: BLOCK DIAGRAM OF A TYPICAL SHARED PORT STRUCTURE

WR LAT +

TRIS Latch

I/O Pin

WR Port

Data Bus

Data Latch

Read Port

Read TRIS

WR TRIS

Peripheral Output Data

Output Enable

Peripheral Input Data

I/O

Peripheral Module

Peripheral Output Enable

PIO Module

Output Multiplexers

Output Data

Input Data

Peripheral Module Enable

Read LAT

 2009-2012 Microchip Technology Inc. DS70616G-page 209

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

11.1.1 OPEN-DRAIN CONFIGURATION

In addition to the PORT, LAT and TRIS registers for

data control, some port pins can also be individually

configured for either digital or open-drain output. This

is controlled by the Open-Drain Control register,

ODCx, associated with each port. Setting any of the

bits configures the corresponding pin to act as an

open-drain output.

The open-drain feature allows the generation of

outputs higher than VDD (e.g., 5V on a 5V tolerant pin)

by using external pull-up resistors. The maximum

open-drain voltage allowed is the same as the

maximum VIH specification for that pin.

See the “Pin Diagrams” section for the available pins

and their functionality.

11.2 Configuring Analog and Digital

Port Pins

The ANSELx register controls the operation of the

analog port pins. The port pins that are to function as

analog inputs or outputs must have their corresponding

ANSELx and TRISx bits set. In order to use port pins for

I/O functionality with digital modules, such as Timers,

UARTs, etc., the corresponding ANSELx bit must be

cleared.

The ANSELx register has a default value of 0xFFFF;

therefore, all pins that share analog functions are

analog (not digital) by default. Refer to the Pinout I/O

Descriptions (Table 1-1 in Section 1.0 “Device

Overview”) for the complete list of analog pins.

If the TRISx bit is cleared (output) while the ANSELx bit

is set, the digital output level (VOH or VOL) is converted

by an analog peripheral, such as the ADC module or

Comparator module.

When the PORT register is read, all pins configured as

analog input channels are read as cleared (a low level).

Pins configured as digital inputs do not convert an

analog input. Analog levels on any pin defined as a

digital input (including the pins defined as Analog in

Table 1-1 in Section 1.0 “Device Overview”) can

cause the input buffer to consume current that

exceeds the device specifications.

11.2.1 I/O PORT WRITE/READ TIMING

One instruction cycle is required between a port

direction change or port write operation and a read

operation of the same port. Typically this instruction

would be an NOP, as shown in Example 11-1.

11.3 Input Change Notification

The input change notification function of the I/O ports

allows the dsPIC33EPXXX(GP/MC/MU)806/810/814

and PIC24EPXXX(GP/GU)810/814 devices to

generate interrupt requests to the processor in

response to a Change-of-State (COS) on selected input

pins. This feature can detect input Change-of-States

even in Sleep mode, when the clocks are disabled.

Every I/O port pin can be selected (enabled) for

generating an interrupt request on a Change-of-State.

Three control registers are associated with the CN

functionality of each I/O port. The CNENx registers

contain the CN interrupt enable control bits for each of

the input pins. Setting any of these bits enables a CN

interrupt for the corresponding pins.

Each I/O pin also has a weak pull-up and a weak

pull-down connected to it. The pull-ups act as a

current source or sink source connected to the pin,

and eliminate the need for external resistors when

push-button or keypad devices are connected. The

pull-ups and pull-downs are enabled separately using

the CNPUx and the CNPDx registers, which contain

the control bits for each of the pins. Setting any of

the control bits enables the weak pull-ups and/or

pull-downs for the corresponding pins.

EXAMPLE 11-1: PORT WRITE/READ

EXAMPLE

Note: Pull-ups and pull-downs on change notifi-

cation pins should always be disabled

when the port pin is configured as a digital

output.

MOV 0xFF00, W0 ; Configure PORTB<15:8>

; as inputs

MOV W0, TRISB ; and PORTB<7:0>

; as outputs

NOP ; Delay 1 cycle

BTSS PORTB, #13 ; Next Instruction

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 210  2009-2012 Microchip Technology Inc.

11.4 Peripheral Pin Select

A major challenge in general purpose devices is provid-

ing the largest possible set of peripheral features while

minimizing the conflict of features on I/O pins. The chal-

lenge is even greater on low pin-count devices. In an

application where more than one peripheral needs to

be assigned to a single pin, inconvenient workarounds

in application code or a complete redesign may be the

only option.

Peripheral Pin Select configuration provides an

alternative to these choices by enabling peripheral set

selection and their placement on a wide range of I/O

pins. By increasing the pinout options available on a

particular device, users can better tailor the device to

their entire application, rather than trimming the

application to fit the device.

The Peripheral Pin Select configuration feature oper-

ates over a fixed subset of digital I/O pins. Users may

independently map the input and/or output of most dig-

ital peripherals to any one of these I/O pins. Peripheral

Pin Select is performed in software and generally does

not require the device to be reprogrammed. Hardware

safeguards are included that prevent accidental or

spurious changes to the peripheral mapping once it has

been established.

11.4.1 AVAILABLE PINS

The number of available pins is dependent on the

particular device and its pin count. Pins that support the

Peripheral Pin Select feature include the designation

“RPn” or “RPIn” in their full pin designation, where “RP”

designates a remappable function for input or output

and “RPI” designates a remappable functions for input

only, and “n” is the remappable pin number.

11.4.2 AVAILABLE PERIPHERALS

The peripherals managed by the Peripheral Pin Select

are all digital only peripherals. These include general

serial communications (UART and SPI), general pur-

pose timer clock inputs, timer-related peripherals (input

capture and output compare) and interrupt-on-change

inputs.

In comparison, some digital-only peripheral modules are

never included in the Peripheral Pin Select feature. This

is because the peripheral’s function requires special I/O

circuitry on a specific port and cannot be easily con-

nected to multiple pins. These modules include I2C and

the PWM. A similar requirement excludes all modules

with analog inputs, such as the ADC Converter.

A key difference between remappable and non-

remappable peripherals is that remappable peripherals

are not associated with a default I/O pin. The peripheral

must always be assigned to a specific I/O pin before it

can be used. In contrast, non-remappable peripherals

are always available on a default pin, assuming that the

peripheral is active and not conflicting with another

peripheral.

When a remappable peripheral is active on a given I/O

pin, it takes priority over all other digital I/O and digital

communication peripherals associated with the pin.

Priority is given regardless of the type of peripheral that

is mapped. Remappable peripherals never take priority

over any analog functions associated with the pin.

11.4.3 CONTROLLING PERIPHERAL PIN

SELECT

Peripheral Pin Select features are controlled through

two sets of SFRs: one to map peripheral inputs and one

to map outputs. Because they are separately con-

trolled, a particular peripheral’s input and output (if the

peripheral has both) can be placed on any selectable

function pin without constraint.

The association of a peripheral to a peripheral-selectable

pin is handled in two different ways, depending on

whether an input or output is being mapped.

11.4.4 INPUT MAPPING

The inputs of the Peripheral Pin Select options are

mapped on the basis of the peripheral. That is, a control

will be mapped to. The RPINRx registers are used to

configure peripheral input mapping (see Register 11-1

through Register 11-22). Each register contains sets of

7-bit fields, with each set associated with one of the

remappable peripherals (see Table 11-1). Programming

a given peripheral’s bit field with an appropriate 7-bit

value maps the RPn/RPIn pin with the corresponding

value to that peripheral (see Table 11-2). For any given

device, the valid range of values for any bit field corre-

sponds to the maximum number of Peripheral Pin

Selections supported by the device.

For example, Figure 11-2 illustrates remappable pin

selection for the U1RX input.

FIGURE 11-2: U1RX REMAPPABLE INPUT

RP0

RP1

RP3

2U1RX Input

U1RXR<6:0>

to Peripheral

RPn/RPIn

Note: For input only, Peripheral Pin Select functionality

does not have priority over TRISx settings.

Therefore, when configuring RPn/RPIn pin for

input, the corresponding bit in the TRISx register

must also be configured for input (set to ‘1’).

 2009-2012 Microchip Technology Inc. DS70616G-page 211

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 11-1: SELECTABLE INPUT SOURCES (MAPS INPUT TO FUNCTION)

Input Name(1)Function Name Register Configuration Bits

External Interrupt 1 INT1 RPINR0 INT1R<6:0>

External Interrupt 2 INT2 RPINR1 INT2R<6:0>

External Interrupt 3 INT3 RPINR1 INT3R<6:0>

External Interrupt 4 INT4 RPINR2 INT4R<6:0>

Timer2 External Clock T2CK RPINR3 T2CKR<6:0>

Timer3 External Clock T3CK RPINR3 T3CKR<6:0>

Timer4 External Clock T4CK RPINR4 T4CKR<6:0>

Timer5 External Clock T5CK RPINR4 T5CKR<6:0>

Timer6 External Clock T6CK RPINR5 T6CKR<6:0>

Timer7 External Clock T7CK RPINR5 T7CKR<6:0>

Timer8 External Clock T8CK RPINR6 T8CKR<6:0>

Timer9 External Clock T9CK RPINR6 T9CKR<6:0>

Input Capture 1 IC1 RPINR7 IC1R<6:0>

Input Capture 2 IC2 RPINR7 IC2R<6:0>

Input Capture 3 IC3 RPINR8 IC3R<6:0>

Input Capture 4 IC4 RPINR8 IC4R<6:0>

Input Capture 5 IC5 RPINR9 IC5R<6:0>

Input Capture 6 IC6 RPINR9 IC6R<6:0>

Input Capture 7 IC7 RPINR10 IC7R<6:0>

Input Capture 8 IC8 RPINR10 IC8R<6:0>

Output Compare Fault A OCFA RPINR11 OCFAR<6:0>

Output Compare Fault B OCFB RPINR11 OCFBR<6:0>

PMW Fault 1(2) FLT1 RPINR12 FLT1R<6:0>

PMW Fault 2(2) FLT2 RPINR12 FLT2R<6:0>

PMW Fault 3(2) FLT3 RPINR13 FLT3R<6:0>

PMW Fault 4(2) FLT4 RPINR13 FLT4R<6:0>

QEI1 Phase A(2) QEA1 RPINR14 QEA1R<6:0>

QEI1 Phase A(2) QEB1 RPINR14 QEB1R<6:0>

QEI1 Index(2) INDX1 RPINR15 INDX1R<6:0>

QEI1 Home(2) HOME1 RPINR15 HOM1R<6:0>

QEI2 Phase A(2) QEA2 RPINR16 QEA2R<6:0>

QEI2 Phase A(2) QEB2 RPINR16 QEB2R<6:0>

QEI2 Index(2) INDX2 RPINR17 INDX2R<6:0>

QEI2 Home(2) HOME2 RPINR17 HOM2R<6:0>

UART1 Receive U1RX RPINR18 U1RXR<6:0>

UART1 Clear-to-Send U1CTS RPINR18 U1CTSR<6:0>

UART2 Receive U2RX RPINR19 U2RXR<6:0>

UART2 Clear-to-Send U2CTS RPINR19 U2CTSR<6:0>

SPI1 Data Input SDI1 RPINR20 SDI1R<6:0>

SPI1 Clock Input SCK1 RPINR20 SCK1R<6:0>

SPI1 Slave Select SS1 RPINR21 SS1R<6:0>

SPI2 Slave Select SS2 RPINR23 SS2R<6:0>

Note 1: Unless otherwise noted, all inputs use the Schmitt Trigger input buffers.

2: This input source is available on dsPIC33EPXXX(MC/MU)806/810/814 devices only.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 212  2009-2012 Microchip Technology Inc.

DCI Data Input CSDI RPINR24 CSDIR<6:0>

DCI Clock Input CSCKIN RPINR24 CSCKR<6:0>

DCI FSYNC Input COFSIN RPINR25 COFSR<6:0>

CAN1 Receive C1RX RPINR26 C1RXR<6:0>

CAN2 Receive C2RX RPINR26 C2RXR<6:0>

UART3 Receive U3RX RPINR27 U3RXR<6:0>

UART3 Clear-to-Send U3CTS RPINR27 U3CTSR<6:0>

UART4 Receive U4RX RPINR28 U4RXR<6:0>

UART4 Clear-to-Send U4CTS RPINR28 U4CTSR<6:0>

SPI3 Data Input SDI3 RPINR29 SDI3R<6:0>

SPI3 Clock Input SCK3 RPINR29 SCK3R<6:0>

SPI3 Slave Select SS3 RPINR30 SS3R<6:0>

SPI4 Data Input SDI4 RPINR31 SDI4R<6:0>

SPI4 Clock Input SCK4 RPINR31 SCK4R<6:0>

SPI4 Slave Select SS4 RPINR32 SS4R<6:0>

Input Capture 9 IC9 RPINR33 IC9R<6:0>

Input Capture 10 IC10 RPINR33 IC10R<6:0>

Input Capture 11 IC11 RPINR34 IC11R<6:0>

Input Capture 12 IC12 RPINR34 IC12R<6:0>

Input Capture 13 IC13 RPINR35 IC13R<6:0>

Input Capture 14 IC14 RPINR35 IC14R<6:0>

Input Capture 15 IC15 RPINR36 IC15R<6:0>

Input Capture 16 IC16 RPINR36 IC16R<6:0>

Output Compare Fault C OCFC RPINR37 OCFCR<6:0>

PWM Fault 5(2)FLT5 RPINR42 FLT5R<6:0>

PWM Fault 6(2)FLT6 RPINR42 FLT6R<6:0>

PWM Fault 7(2)FLT7 RPINR43 FLT7R<6:0>

PWM Dead-Time

Compensation 1(2)

DTCMP1 RPINR38 DTCMP1R<6:0>

PWM Dead-Time

Compensation 2(2)

DTCMP2 RPINR39 DTCMP2R<6:0>

PWM Dead-Time

Compensation 3(2)

DTCMP3 RPINR39 DTCMP3R<6:0>

PWM Dead-Time

Compensation 4(2)

DTCMP4 RPINR40 DTCMP4R<6:0>

PWM Dead-Time

Compensation 5(2)

DTCMP5 RPINR40 DTCMP5R<6:0>

PWM Dead-Time

Compensation 6(2)

DTCMP6 RPINR41 DTCMP6R<6:0>

PWM Dead-Time

Compensation 7(2)

DTCMP7 RPINR41 DTCMP7R<6:0>

PWM Synch Input 1(2)SYNCI1 RPINR37 SYNCI1R<6:0>

PWM Synch Input 2(2)SYNCI2 RPINR38 SYNCI2R<6:0>

TABLE 11-1: SELECTABLE INPUT SOURCES (MAPS INPUT TO FUNCTION) (CONTINUED)

Input Name(1)Function Name Register Configuration Bits

Note 1: Unless otherwise noted, all inputs use the Schmitt Trigger input buffers.

2: This input source is available on dsPIC33EPXXX(MC/MU)806/810/814 devices only.

 2009-2012 Microchip Technology Inc. DS70616G-page 213

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 11-2: INPUT PIN SELECTION FOR SELECTABLE INPUT SOURCES

Peripheral Pin Select

Input Register Value

Input/

Output Pin Assignment Peripheral Pin Select

Input Register Value

Input/

Output Pin Assignment

000 0000 IV

SS 010 1101 IRPI45

000 0001 IC1OUT

(1) 010 1110 IRPI46

000 0010 IC2OUT

(1)010 1111 IRPI47

000 0011 IC3OUT

(1)011 0000 —Reserved

000 0100 —Reserved 011 0001 IRPI49

000 0101 —Reserved 011 0010 IRPI50

000 0110 —Reserved 011 0011 IRPI51

000 0111 —Reserved 011 0100 IRPI52

000 1000 IFINDX1

(1) 011 0101 —Reserved

000 1001 IFHOME1

(1) 011 0110 —Reserved

000 1010 IFINDX2

(1) 011 0111 —Reserved

000 1011 IFHOME2

(1) 011 1000 —Reserved

000 1100 —Reserved 011 1001 —Reserved

000 1101 —Reserved 011 1010 —Reserved

000 1110 —Reserved 011 1011 —Reserved

000 1111 —Reserved 011 1100 IRPI60

001 0000 IRPI16 011 1101 IRPI61

001 0001 IRPI17 011 1110 IRPI62

001 0010 IRPI18 011 1111 —Reserved

001 0011 IRPI19 100 0000 I/O RP64

001 0100 IRPI20 100 0001 I/O RP65

001 0101 IRPI21 100 0010 I/O RP66

001 0110 IRPI22 100 0011 I/O RP67

001 0111 IRPI23 100 0100 I/O RP68

001 1000 —Reserved 100 0101 I/O RP69

001 1001 —Reserved 100 0110 I/O RP70

001 1010 —Reserved 100 0111 I/O RP71

001 1011 —Reserved 100 1000 IRPI72

001 1100 —Reserved 100 1001 IRPI73

001 1101 —Reserved 100 1010 IRPI74

001 1110 IRPI30 100 1011 IRPI75

001 1111 IRPI31 100 1100 IRPI76

010 0000 IRPI32 100 1101 IRPI77

010 0001 IRPI33 100 1110 IRPI78

010 0010 IRPI34 100 1111 I/O RP79

010 0011 IRPI35 101 0000 I/O RP80

010 0100 IRPI36 101 0001 IRPI81

010 0101 IRPI37 101 0010 I/O RP82

010 0110 IRPI38 101 0011 IRPI83

010 0111 IRPI39 101 0100 I/O RP84

010 1000 IRPI40 101 0101 I/O RP85

010 1001 IRPI41 101 0110 IRPI86

010 1010 IRPI42 101 0111 I/O RP87

Note 1: See Section 11.4.4.2 “Virtual Connections” for more information on selecting this pin assignment.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 214  2009-2012 Microchip Technology Inc.

010 1011 IRPI43 101 1000 IRPI88

010 1100 IRPI44 101 1001 IRPI89

101 1010 —Reserved 110 1101 I/O RP109

101 1011 —Reserved 110 1110 —Reserved

101 1100 —Reserved 110 1111 —Reserved

101 1101 —Reserved 111 0000 I/O RP112

101 1110 —Reserved 111 0001 I/O RP113

101 1111 —Reserved 111 0010 —Reserved

110 0000 I/O RP96 111 0011 —Reserved

110 0001 I/O RP97 111 0100 —Reserved

110 0010 I/O RP98 111 0101 —Reserved

110 0011 I/O RP99 111 0110 I/O RP118

110 0100 I/O RP100 111 0111 IRPI119

110 0101 I/O RP101 111 1000 I/O RP120

110 0110 I/O RP102 111 1001 IRPI121

110 0111 —Reserved 111 1010 —Reserved

110 1000 I/O RP104 111 1011 —Reserved

110 1001 —Reserved 111 1100 IRPI124

110 1010 —Reserved 111 1101 I/O RP125

110 1011 —Reserved 111 1110 I/O RP126

110 1100 I/O RP108 111 1111 I/O RP127

TABLE 11-2: INPUT PIN SELECTION FOR SELECTABLE INPUT SOURCES (CONTINUED)

Peripheral Pin Select

Input Register Value

Input/

Output Pin Assignment Peripheral Pin Select

Input Register Value

Input/

Output Pin Assignment

Note 1: See Section 11.4.4.2 “Virtual Connections” for more information on selecting this pin assignment.

 2009-2012 Microchip Technology Inc. DS70616G-page 215

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

11.4.4.1 Output Mapping

In contrast to inputs, the outputs of the Peripheral Pin

Select options are mapped on the basis of the pin. In

this case, a control register associated with a particular

pin dictates the peripheral output to be mapped. The

RPORx registers are used to control output mapping.

Like the RPINRx registers, each register contains sets

of 6 bit fields, with each set associated with one RPn

pin (see Register 11-44 through Register 11-51). The

value of the bit field corresponds to one of the periph-

erals and that peripheral’s output is mapped to the pin

(see Table 11-3 and Figure 11-3).

A null output is associated with the Output Register

Reset value of ‘0’. This is done to ensure that remap-

pable outputs remain disconnected from all output pins

by default.

FIGURE 11-3: MULTIPLEXING OF

REMAPPABLE OUTPUT

FOR RPn

RPnR<5:0>

Default

U1TX Output

U1RTS Output 2

REFCLK Output

QEI2CCMP Output

Output Data RPn

TABLE 11-3: OUTPUT SELECTION FOR REMAPPABLE PINS (RPn)

Function RPnR<5:0> Output Name

DEFAULT PORT 000000 RPn tied to Default Pin

U1TX 000001 RPn tied to UART1 Transmit

U1RTS 000010 RPn tied to UART1 Ready-to-Send

U2TX 000011 RPn tied to UART2 Transmit

U2RTS 000100 RPn tied to UART2 Ready-to-Send

SDO1 000101 RPn tied to SPI1 Data Output

SCK1 000110 RPn tied to SPI1 Clock Output

SS1 000111 RPn tied to SPI1 Slave Select

SS2 001010 RPn tied to SPI2 Slave Select

CSDO 001011 RPn tied to DCI Data Output

CSCK 001100 RPn tied to DCI Clock Output

COFS 001101 RPn tied to DCI FSYNC Output

C1TX 001110 RPn tied to CAN1 Transmit

C2TX 001111 RPn tied to CAN2 Transmit

OC1 010000 RPn tied to Output Compare 1 Output

OC2 010001 RPn tied to Output Compare 2 Output

OC3 010010 RPn tied to Output Compare 3 Output

OC4 010011 RPn tied to Output Compare 4 Output

OC5 010100 RPn tied to Output Compare 5 Output

OC6 010101 RPn tied to Output Compare 6 Output

OC7 010110 RPn tied to Output Compare 7 Output

OC8 010111 RPn tied to Output Compare 8 Output

C1OUT 011000 RPn tied to Comparator Output 1

C2OUT 011001 RPn tied to Comparator Output 2

C3OUT 011010 RPn tied to Comparator Output 3

U3TX 011011 RPn tied to UART3 Transmit

U3RTS 011100 RPn tied to UART3 Ready-to-Send

Note 1: This function is available in dsPIC33EPXXX(MC/MU)806/810/814 devices only.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 216  2009-2012 Microchip Technology Inc.

U4TX 011101 RPn tied to UART4 Transmit

U4RTS 011110 RPn tied to UART4 Ready-to-Send

SDO3 011111 RPn tied to SPI3 Data Output

SCK3 100000 RPn tied to SPI3 Clock Output

SS3 100001 RPn tied to SPI3 Slave Select

SDO4 100010 RPn tied to SPI4 Data Output

SCK4 100011 RPn tied to SPI4 Clock Output

SS4 100100 RPn tied to SPI4 Slave Select

OC9 100101 RPn tied to Output Compare 9 Output

OC10 100110 RPn tied to Output Compare 10 Output

OC11 100111 RPn tied to Output Compare 11 Output

OC12 101000 RPn tied to Output Compare 12 Output

OC13 101001 RPn tied to Output Compare 13 Output

OC14 101010 RPn tied to Output Compare 14 Output

OC15 101011 RPn tied to Output Compare 15 Output

OC16 101100 RPn tied to Output Compare 16 Output

SYNCO1(1)101101 RPn tied to PWM Primary Time Base Sync Output

SYNCO2(1)101110 RPn tied to PWM Secondary Time Base Sync Output

QEI1CCMP(1)101111 RPn tied to QEI 1 Counter Comparator Output

QEI2CCMP(1)110000 RPn tied to QEI 2 Counter Comparator Output

REFCLK 110001 RPn tied to Reference Clock Output

TABLE 11-3: OUTPUT SELECTION FOR REMAPPABLE PINS (RPn) (CONTINUED)

Function RPnR<5:0> Output Name

Note 1: This function is available in dsPIC33EPXXX(MC/MU)806/810/814 devices only.

 2009-2012 Microchip Technology Inc. DS70616G-page 217

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

11.4.4.2 Virtual Connections

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices support virtual

(internal) connections to the output of the comparator

modules, CMP1OUT, CMP2OUT and CMP3OUT (see

Figure 25-1 in Section 25.0 “Comparator Module”).

In addition, dsPIC33EPXXXMU806/810/814 devices

support virtual connections to the filtered QEI module

inputs, FINDX1, FHOME1, FINDX2 and FHOME2 (see

Figure 17-1 in Section 17.0 “Quadrature Encoder

Interface (QEI) Module (dsPIC33EPXXX(MC/

MU)8XX Devices Only)”.

Virtual connections provide a simple way of inter-

peripheral connection without utilizing a physical pin.

For example, by setting the FLT1R<6:0> bits of the

RPINR12 register to the value of ‘b0000001, the

output of the analog comparator, CMP1OUT, will be

connected to the PWM Fault 1 input, which allows the

analog comparator to trigger PWM Faults without the

use of an actual physical pin on the device.

Virtual connection to the QEI module allows

peripherals to be connected to the QEI digital filter

input. To utilize this filter, the QEI module must be

enabled, and its inputs must be connected to a physical

RPn/RPIn pin. Example 11-2 illustrates how the input

capture module can be connected to the QEI digital

filter.

11.4.4.3 Mapping Limitations

The control schema of the peripheral select pins is not

limited to a small range of fixed peripheral

configurations. There are no mutual or hardware

enforced lockouts between any of the peripheral

mapping SFRs. Literally any combination of peripheral

mappings across any or all of the RPn/RPIn pins is

possible. This includes both many-to-one and one-to-

many mappings of peripheral inputs and outputs to

pins. While such mappings may be technically possible

from a configuration point of view, they may not be

supportable from an electrical point of view.

EXAMPLE 11-2: CONNECTING IC1 TO HOME1 DIGITAL FILTER INPUT ON PIN 3 OF THE

dsPIC33EP512MU810 DEVICE

RPINR15 = 0x5600; /* Connect the QEI1 HOME1 input to RP86 (pin 3) */

RPINR7 = 0x009; /* Connect the IC1 input to the digital filter on the FHOME1 input */

QEI1IOC = 0x4000; /* Enable the QEI digital filter */

QEI1CON = 0x8000; /* Enable the QEI module */

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 218  2009-2012 Microchip Technology Inc.

11.5 I/O Helpful Tips

1. In some cases, certain pins, as defined in

Table 32-9 in Section 32.0 “Electrical Charac-

teristics” under “Injection Current”, have internal

protection diodes to VDD and VSS; the term

“Injection Current” is also referred to as “Clamp

Current”. On designated pins, with sufficient exter-

nal current-limiting precautions by the user, I/O pin

input voltages are allowed to be greater or less

than the data sheet absolute maximum ratings

with respect to the VSS and VDD supplies. Note

that when the user application forward biases

either of the high or low side internal input clamp

diodes, that the resulting current being injected

into the device that is clamped internally by the

VDD and VSS power rails, may affect the ADC

accuracy by four to six counts.

2. I/O pins that are shared with any analog input pin,

(i.e., ANx, see Tab l e 1 - 1 in Section 1.0 “Device

Overview”), are always analog pins by default

after any Reset. Consequently, configuring a pin

as an analog input pin, automatically disables the

digital input pin buffer and any attempt to read the

digital input level by reading PORTx or LATx will

always return a ‘0’, regardless of the digital logic

level on the pin. To use a pin as a digital I/O pin on

a shared analog pin (see Table 1-1 in Section 1.0

“Device Overview”), the user application needs

to configure the Analog Pin Configuration registers

in the I/O ports module (i.e., ANSELx) by setting

the appropriate bit that corresponds to that I/O port

pin to a ‘0’.

3. Most I/O pins have multiple functions. Referring to

the device pin diagrams in the data sheet, the

priorities of the functions allocated to any pins are

indicated by reading the pin name from left to right.

The left most function name takes precedence

over any function to its right in the naming conven-

tion. For example: AN16/T2CK/T7CK/RC1; this

indicates that AN16 is the highest priority in this

example and will supersede all other functions to

its right in the list. Those other functions to its right,

even if enabled, would not work as long as any

other function to its left was enabled. This rule

applies to all of the functions listed for a given pin.

Dedicated peripheral functions are always higher

priority than remappable functions. I/O pins are

always the lowest priority.

4. Each pin has an internal weak pull-up resistor and

pull-down resistor that can be configured using the

CNPUx and CNPDx registers, respectively. These

resistors eliminate the need for external resistors

in certain applications. The internal pull-up is up to

~(VDD-0.8), not VDD. This value is still above the

minimum VIH of CMOS and TTL devices.

5. When driving LEDs directly, the I/O pin can source

or sink more current than what is specified in the

VOH/IOH and VOL/IOL DC characteristic specifica-

tion. The respective IOH and IOL current rating only

applies to maintaining the corresponding output at

or above the VOH and at or below the VOL levels.

However, for LEDs, unlike digital inputs of an

externally connected device, they are not gov-

erned by the same minimum VIH/VIL levels. An I/O

pin output can safely sink or source any current

less than that listed in the absolute maximum

rating section of the data sheet. For example:

VOH = 2.4v @ IOH = -8 mA and VDD = 3.3V

The maximum output current sourced by any 8 mA

I/O pin = 12 mA.

LED source current < 12 mA is technically

permitted. Refer to the VOH/IOH graphs in

Section 32.0 “Electrical Characteristics” for

additional information.

6. The Peripheral Pin Select (PPS) pin mapping rules

are as follows:

a) Only one “output” function can be active on a

given pin at any time regardless if it is a dedi-

cated or remappable function (one pin, one

output).

b) It is possible to assign a “remappable output”

function to multiple pins and externally short or

tie them together for increased current drive.

c) If any “dedicated output” function is enabled

on a pin, it will take precedence over any

remappable “output” function.

d) If any “dedicated digital” (input or output)

function is enabled on a pin, any number of

“input” remappable functions can be mapped

to the same pin.

e) If any “dedicated analog” function(s) are

enabled on a given pin, “digital input(s)” of any

kind will all be disabled, although a single “dig-

ital output”, at the user’s cautionary discretion,

can be enabled and active as long as there is

no signal contention with an external analog

input signal. For example, it is possible for the

ADC to convert the digital output logic level, or

to toggle a digital output on a comparator or

ADC input, provided there is no external

analog input, such as for a built-in self test.

f) Any number of “input” remappable functions

can be mapped to the same pin(s) at the

same time, including any pin with a single out-

put from either a dedicated or remappable

“output”.

Note: Although it is not possible to use a digital

input pin when its analog function is

enabled, it is possible to use the digital I/O

output function, TRISx = 0x0, while the

analog function is also enabled. However,

this is not recommended, particularly if the

analog input is connected to an external

analog voltage source, which would

create signal contention between the

analog signal and the output pin driver.

 2009-2012 Microchip Technology Inc. DS70616G-page 219

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

g) The TRIS registers control only the digital I/O

output buffer. Any other dedicated or remap-

pable active “output” will automatically over-

ride the TRIS setting. The TRIS register does

not control the digital logic “input” buffer.

Remappable digital “inputs” do not automati-

cally override TRIS settings, which means

that the TRIS bit must be set to input for pins

with only remappable input function(s)

assigned.

h) All analog pins are enabled by default after

any Reset and the corresponding digital input

buffer on the pin is disabled. Only the Analog

Pin Select registers control the digital input

buffer, not the TRIS register. The user must

disable the analog function on a pin using the

Analog Pin Select registers in order to use any

“digital input(s)” on a corresponding pin, no

exceptions.

11.6 I/O Resources

Many useful resources related to I/O are provided on

the main product page of the Microchip web site for the

devices listed in this data sheet. This product page,

which can be accessed using this link, contains the

latest updates and additional information.

11.6.1 KEY RESOURCES

•Section 10. “I/O Ports” (DS70598) in the

“dsPIC33E/PIC24E Family Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554301

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 220  2009-2012 Microchip Technology Inc.

11.7 Peripheral Pin Select Control

Registers

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—INT1R<6:0>

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 INT1R<6:0>: Assign External Interrupt 1 (INT1) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7-0 Unimplemented: Read as ‘0’

 2009-2012 Microchip Technology Inc. DS70616G-page 221

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—INT3R<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—INT2R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 INT3R<6:0>: Assign External Interrupt 3 (INT3) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 INT2R<6:0>: Assign External Interrupt 2 (INT2) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 222  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—INT4R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-7 Unimplemented: Read as ‘0’

bit 6-0 INT4R<6:0>: Assign External Interrupt 4 (INT4) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

 2009-2012 Microchip Technology Inc. DS70616G-page 223

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—T3CKR<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—T2CKR<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 T3CKR<6:0>: Assign Timer3 External Clock (T3CK) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 T2CKR<6:0>: Assign Timer2 External Clock (T2CK) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 224  2009-2012 Microchip Technology Inc.

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—T5CKR<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—T4CKR<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 T5CKR<6:0>: Assign Timer5 External Clock (T5CK) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 T4CKR<6:0>: Assign Timer4 External Clock (T4CK) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

 2009-2012 Microchip Technology Inc. DS70616G-page 225

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—T7CKR<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—T6CKR<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 T7CKR<6:0>: Assign Timer7 External Clock (T7CK) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 T6CKR<6:0>: Assign Timer6 External Clock (T6CK) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 226  2009-2012 Microchip Technology Inc.

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—T9CKR<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—T8CKR<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 T9CKR<6:0>: Assign Timer9 External Clock (T9CK) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 T8CKR<6:0>: Assign Timer8 External Clock (T8CK) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

 2009-2012 Microchip Technology Inc. DS70616G-page 227

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— IC2R<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— IC1R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 IC2R<6:0>: Assign Input Capture 2 (IC2) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 IC1R<6:0>: Assign Input Capture 1 (IC1) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 228  2009-2012 Microchip Technology Inc.

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— IC4R<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— IC3R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 IC4R<6:0>: Assign Input Capture 4 (IC4) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 IC3R<6:0>: Assign Input Capture 3 (IC3) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

 2009-2012 Microchip Technology Inc. DS70616G-page 229

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— IC6R<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— IC5R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 IC6R<6:0>: Assign Input Capture 6 (IC6) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 IC5R<6:0>: Assign Input Capture 5 (IC5) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 230  2009-2012 Microchip Technology Inc.

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— IC8R<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— IC7R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 IC8R<6:0>: Assign Input Capture 8 (IC8) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 IC7R<6:0>: Assign Input Capture 7 (IC7) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

 2009-2012 Microchip Technology Inc. DS70616G-page 231

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—OCFBR<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—OCFAR<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 OCFBR<6:0>: Assign Output Compare Fault B (OCFB) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 OCFAR<6:0>: Assign Output Compare Fault A (OCFA) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 232  2009-2012 Microchip Technology Inc.

(dsPIC33EPXXXMU806/810/814 DEVICES ONLY)

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—FLT2R<6:0>

(1)

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—FLT1R<6:0>

(1)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 FLT2R<6:0>: Assign PWM Fault 2 (FLT2) to the Corresponding RPn/RPIn Pin bits(1)

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 FLT1R<6:0>: Assign PWM Fault 1 (FLT1) to the Corresponding RPn/RPIn Pin bits(1)

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

Note 1: These pins are available on dsPIC33EPXXX(MC/MU)806/810/814 devices only.

 2009-2012 Microchip Technology Inc. DS70616G-page 233

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

(dsPIC33EPXXXMU806/810/814 DEVICES ONLY)

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—FLT4R<6:0>

(1)

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—FLT3R<6:0>

(1)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 FLT4R<6:0>: Assign PWM Fault 4 (FLT4) to the Corresponding RPn/RPIn Pin bits(1)

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 FLT3R<4:0>: Assign PWM Fault 3 (FLT3) to the Corresponding RPn/RPIn Pin bits(1)

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

Note 1: These pins are available on dsPIC33EPXXX(MC/MU)806/810/814 devices only.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 234  2009-2012 Microchip Technology Inc.

(dsPIC33EPXXXMU806/810/814 DEVICES ONLY)

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— QEB1R<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— QEA1R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 QEB1R<6:0>: Assign B (QEB) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 QEA1R<6:0>: Assign A (QEA) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

 2009-2012 Microchip Technology Inc. DS70616G-page 235

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

(dsPIC33EPXXXMU806/810/814 DEVICES ONLY)

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— HOME1R<6:0>(1)

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— INDX1R<6:0>(1)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 HOME1R<6:0>: Assign QEI1 HOME1 (HOME1) to the Corresponding RPn/RPIn Pin bits(1)

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 IND1XR<6:0>: Assign QEI1 INDEX1 (INDX1) to the Corresponding RPn/RPIn Pin bits(1)

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

Note 1: These bits are available on dsPIC33EPXXX(MC/MU)806/810/814 devices only.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 236  2009-2012 Microchip Technology Inc.

(dsPIC33EPXXXMU806/810/814 DEVICES ONLY)

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— QEB2R<6:0>(1)

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— QEA2R<6:0>(1)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 QEB2R<6:0>: Assign B (QEI2) to the Corresponding RPn/RPIn Pin bits(1)

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 QEA2R<6:0>: Assign A (QEI2) to the Corresponding RPn/RPIn Pin bits(1)

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

Note 1: These bits are available on dsPIC33EPXXX(MC/MU)806/810/814 devices only.

 2009-2012 Microchip Technology Inc. DS70616G-page 237

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

(dsPIC33EPXXXMU806/810/814 DEVICES ONLY)

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— HOME2R<6:0>(1)

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— INDX2R<6:0>(1)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 HOME2R<6:0>: Assign QEI2 HOME2 (HOME2) to the Corresponding RPn/RPIn Pin bits(1)

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 INDX2R<6:0>: Assign QEI2 INDEX2 (INDX2) to the Corresponding RPn/RPIn Pin bits(1)

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

Note 1: These bits are available on dsPIC33EPXXX(MC/MU)806/810/814 devices only.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 238  2009-2012 Microchip Technology Inc.

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— U1CTSR<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—U1RXR<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 U1CTSR<6:0>: Assign UART1 Clear-to-Send (U1CTS) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 U1RXR<6:0>: Assign UART1 Receive (U1RX) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

 2009-2012 Microchip Technology Inc. DS70616G-page 239

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— U2CTSR<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—U2RXR<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 U2CTSR<6:0>: Assign UART2 Clear-to-Send (U2CTS) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 U2RXR<6:0>: Assign UART2 Receive (U2RX) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 240  2009-2012 Microchip Technology Inc.

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—SCK1R<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—SDI1R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 SCK1R<6:0>: Assign SPI1 Clock Input (SCK1) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 SDI1R<6:0>: Assign SPI1 Data Input (SDI1) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

 2009-2012 Microchip Technology Inc. DS70616G-page 241

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— SS1R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-7 Unimplemented: Read as ‘0’

bit 6-0 SS1R<6:0>: Assign SPI1 Slave Select Input (SS1) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— SS2R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-7 Unimplemented: Read as ‘0’

bit 6-0 SS2R<6:0>: Assign SPI2 Slave Select Input (SS2) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 242  2009-2012 Microchip Technology Inc.

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— CSCKR<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—CSDIR<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 CSCKR<6:0>: Assign DCI Clock Input (CSCK) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 CSDIR<6:0>: Assign DCI Data Input (CSDI) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

 2009-2012 Microchip Technology Inc. DS70616G-page 243

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— COFSR<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-7 Unimplemented: Read as ‘0’

bit 6-0 COFSR<6:0>: Assign DCI FSYNC Input (COFS) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 244  2009-2012 Microchip Technology Inc.

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—C2RXR<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—C1RXR<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 C2RXR<6:0>: Assign CAN2 RX Input (CRX2) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 C1RXR<6:0>: Assign CAN1 RX Input (CRX1) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

 2009-2012 Microchip Technology Inc. DS70616G-page 245

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— U3CTSR<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—U3RXR<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 U3CTSR<6:0>: Assign UART3 Clear-to-Send (U3CTS) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 U3RXR<6:0>: Assign UART3 Receive (U3RX) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 246  2009-2012 Microchip Technology Inc.

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— U4CTSR<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—U4RXR<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 U4CTSR<6:0>: Assign UART4 Clear-to-Send (U4CTS) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 U4RXR<6:0>: Assign UART4 Receive (U4RX) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

 2009-2012 Microchip Technology Inc. DS70616G-page 247

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—SCK3R<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—SDI3R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 SCK3R<6:0>: Assign SPI3 Clock Input (SCK3) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 SDI3R<6:0>: Assign SPI3 Data Input (SDI3) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 248  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— SS3R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-7 Unimplemented: Read as ‘0’

bit 6-0 SS3R<6:0>: Assign SPI3 Slave Select Input (SS3) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

 2009-2012 Microchip Technology Inc. DS70616G-page 249

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—SCK4R<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—SDI4R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 SCK4R<6:0>: Assign SPI4 Clock Input (SCK4) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 SDI4R<6:0>: Assign SPI4 Data Input (SDI4) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 250  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— SS4R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-7 Unimplemented: Read as ‘0’

bit 6-0 SS4R<6:0>: Assign SPI4 Slave Select Input (SS4) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

 2009-2012 Microchip Technology Inc. DS70616G-page 251

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— IC10R<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— IC9R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 IC10R<6:0>: Assign Input Capture 10 (IC10) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 IC9R<6:0>: Assign Input Capture 9 (IC9) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 252  2009-2012 Microchip Technology Inc.

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— IC12R<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—IC11R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 IC12R<6:0>: Assign Input Capture 12 (IC12) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 IC11R<6:0>: Assign Input Capture 11 (IC11) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

 2009-2012 Microchip Technology Inc. DS70616G-page 253

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— IC14R<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— IC13R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 IC14R<6:0>: Assign Input Capture 14 (IC14) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 IC13R<6:0>: Assign Input Capture 13 (IC13) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 254  2009-2012 Microchip Technology Inc.

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— IC16R<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— IC15R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 IC16R<6:0>: Assign Input Capture 16 (IC16) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 IC15R<6:0>: Assign Input Capture 15 (IC15) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

 2009-2012 Microchip Technology Inc. DS70616G-page 255

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— SYNCI1R<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— OCFCR<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 SYNCI1R<6:0>: Assign PWM Synchronization Input 1 to the Corresponding RPn/RPIn Pin bits.

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 OCFCR<6:0>: Assign Output Fault C (OCFC) to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 256  2009-2012 Microchip Technology Inc.

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—DTCMP1R<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— SYNCI2R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 DTCMP1R<6:0>: Assign PWM Dead-Time Compensation Input 1 to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 SYNCI2R<6:0>: Assign PWM Synchronization Input 2 to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

 2009-2012 Microchip Technology Inc. DS70616G-page 257

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—DTCMP3R<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—DTCMP2R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 DTCMP3R<6:0>: Assign PWM Dead-Time Compensation Input 3 to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 DTCMP2R<6:0>: Assign PWM Dead-Time Compensation Input 2 to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 258  2009-2012 Microchip Technology Inc.

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—DTCMP5R<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—DTCMP4R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 DTCMP5R<6:0>: Assign PWM Dead-Time Compensation Input 5 to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 DTCMP4R<6:0>: Assign PWM Dead-Time Compensation Input 4 to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

 2009-2012 Microchip Technology Inc. DS70616G-page 259

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—DTCMP7R<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—DTCMP6R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 DTCMP7R<6:0>: Assign PWM Dead-Time Compensation Input 7 to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 DTCMP6R<6:0>: Assign PWM Dead-Time Compensation Input 6 to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 260  2009-2012 Microchip Technology Inc.

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—FLT6R<6:0>

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—FLT5R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-8 FLT6R<6:0>: Assign PWM Fault 6 to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

bit 7 Unimplemented: Read as ‘0’

bit 6-0 FLT5R<6:0>: Assign PWM Fault 5 to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

 2009-2012 Microchip Technology Inc. DS70616G-page 261

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—FLT7R<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-7 Unimplemented: Read as ‘0’

bit 6-0 FLT7R<6:0>: Assign PWM Fault 7 to the Corresponding RPn/RPIn Pin bits

(see Tab l e 11 -2 for input pin selection numbers)

1111111 = Input tied to RP127

0000001 = Input tied to CMP1

0000000 = Input tied to VSS

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP65R<5:0>

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP64R<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-8 RP65R<5:0>: Peripheral Output Function is Assigned to RP65 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

bit 7-6 Unimplemented: Read as ‘0’

bit 5-0 RP64R<5:0>: Peripheral Output Function is Assigned to RP64 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 262  2009-2012 Microchip Technology Inc.

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP67R<5:0>

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP66R<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-8 RP67R<5:0>: Peripheral Output Function is Assigned to RP67 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

bit 7-6 Unimplemented: Read as ‘0’

bit 5-0 RP66R<5:0>: Peripheral Output Function is Assigned to RP66 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP69R<5:0>

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP68R<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-8 RP69R<5:0>: Peripheral Output Function is Assigned to RP69 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

bit 7-6 Unimplemented: Read as ‘0’

bit 5-0 RP68R<5:0>: Peripheral Output Function is Assigned to RP68 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

 2009-2012 Microchip Technology Inc. DS70616G-page 263

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP71R<5:0>

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP70R<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-8 RP71R<5:0>: Peripheral Output Function is Assigned to RP71 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

bit 7-6 Unimplemented: Read as ‘0’

bit 5-0 RP70R<5:0>: Peripheral Output Function is Assigned to RP70 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP80R<5:0>

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP79R<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-8 RP80R<5:0>: Peripheral Output Function is Assigned to RP80 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

bit 7-6 Unimplemented: Read as ‘0’

bit 5-0 RP79R<5:0>: Peripheral Output Function is Assigned to RP79 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 264  2009-2012 Microchip Technology Inc.

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP84R<5:0>

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP82R<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-8 RP84R<5:0>: Peripheral Output Function is Assigned to RP84 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

bit 7-6 Unimplemented: Read as ‘0’

bit 5-0 RP82R<5:0>: Peripheral Output Function is Assigned to RP82 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP87R<5:0>

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP85R<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-8 RP87R<5:0>: Peripheral Output Function is Assigned to RP87 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

bit 7-6 Unimplemented: Read as ‘0’

bit 5-0 RP85R<5:0>: Peripheral Output Function is Assigned to RP85 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

 2009-2012 Microchip Technology Inc. DS70616G-page 265

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP97R<5:0>

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP96R<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-8 RP97R<5:0>: Peripheral Output Function is Assigned to RP97 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

bit 7-6 Unimplemented: Read as ‘0’

bit 5-0 RP96R<5:0>: Peripheral Output Function is Assigned to RP96 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP99R<5:0>

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP98R<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-8 RP99R<5:0>: Peripheral Output Function is Assigned to RP99 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

bit 7-6 Unimplemented: Read as ‘0’

bit 5-0 RP98R<5:0>: Peripheral Output Function is Assigned to RP98 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 266  2009-2012 Microchip Technology Inc.

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP101R<5:0>

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP100R<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-8 RP101R<5:0>: Peripheral Output Function is Assigned to RP101Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

bit 7-6 Unimplemented: Read as ‘0’

bit 5-0 RP100R<5:0>: Peripheral Output Function is Assigned to RP100 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP102R<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-6 Unimplemented: Read as ‘0’

bit 5-0 RP102R<5:0>: Peripheral Output Function is Assigned to RP102 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

 2009-2012 Microchip Technology Inc. DS70616G-page 267

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP108R<5:0>

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP104R<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-8 RP108R<5:0>: Peripheral Output Function is Assigned to RP108 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

bit 7-6 Unimplemented: Read as ‘0’

bit 5-0 RP104R<5:0>: Peripheral Output Function is Assigned to RP104 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP112R<5:0>

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP109R<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-8 RP112R<5:0>: Peripheral Output Function is Assigned to RP112 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

bit 7-6 Unimplemented: Read as ‘0’

bit 5-0 RP109R<5:0>: Peripheral Output Function is Assigned to RP109 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 268  2009-2012 Microchip Technology Inc.

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP118R<5:0>

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP113R<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-8 RP118R<5:0>: Peripheral Output Function is Assigned to RP118 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

bit 7-6 Unimplemented: Read as ‘0’

bit 5-0 RP113R<5:0>: Peripheral Output Function is Assigned to RP113 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP125R<5:0>

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP120R<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-8 RP125R<5:0>: Peripheral Output Function is Assigned to RP125 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

bit 7-6 Unimplemented: Read as ‘0’

bit 5-0 RP120R<5:0>: Peripheral Output Function is Assigned to RP120 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

 2009-2012 Microchip Technology Inc. DS70616G-page 269

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP127R<5:0>

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— RP126R<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-8 RP127R<5:0>: Peripheral Output Function is Assigned to RP127 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

bit 7-6 Unimplemented: Read as ‘0’

bit 5-0 RP126R<5:0>: Peripheral Output Function is Assigned to RP126 Output Pin bits

(see Tab l e 11 -3 for peripheral function numbers)

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 270  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 271

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

12.0 TIMER1

The Timer1 module is a 16-bit timer, which can serve

as the time counter for the real-time clock, or operate

as a free-running interval timer/counter.

The Timer1 module has the following unique features

over other timers:

• Can be operated from the low-power 32 kHz

crystal oscillator available on the device.

• Can be operated in Asynchronous Counter mode

from an external clock source.

• The external clock input (T1CK) can optionally be

synchronized to the internal device clock and clock

synchronization is performed after the prescaler.

The unique features of Timer1 allow it to be used for

Real-Time Clock (RTC) applications. A block diagram

of Timer1 is shown in Figure 12-1.

The Timer1 module can operate in one of the following

modes:

• Timer mode

• Gated Timer mode

• Synchronous Counter mode

• Asynchronous Counter mode

In Timer and Gated Timer modes, the input clock is

derived from the internal instruction cycle clock (FCY).

In Synchronous and Asynchronous Counter modes,

the input clock is derived from the external clock input

at the T1CK pin.

The Timer modes are determined by the following bits:

• Timer Clock Source Control bit (TCS): T1CON<1>

• Timer Synchronization Control bit (TSYNC):

T1CON<2>

• Timer Gate Control bit (TGATE): T1CON<6>

Timer control bit setting for different operating modes

are given in the Table 12-1.

TABLE 12-1: TIMER MODE SETTINGS

FIGURE 12-1: 16-BIT TIMER1 MODULE BLOCK DIAGRAM

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this

data sheet, refer to Section 11. “Timers”

(DS70362) of the “dsPIC33E/PIC24E

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Mode TCS TGATE TSYNC

Timer 00x

Gated Timer 01x

Synchronous Counter 1x1

Asynchronous Counter 1x0

TGATE

TCS

Comparator

TGATE

Set T1IF Flag

TSYNC

Sync

Equal

Reset

SOSCI

SOSCO/

T1CK

Prescaler

(/n)

TCKPS<1:0>

Gate

Sync

FP(1)

Falling Edge

Detect

Prescaler

(/n)

TCKPS<1:0>

LPOSCEN(2)

Note 1: FP is the peripheral clock.

2: See Section 9.0 “Oscillator Configuration” for information on enabling the Secondary Oscillator (SOSC).

Latch

Data

CLK

T1CLK

TMR1

PR1

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 272  2009-2012 Microchip Technology Inc.

12.1 Timer Resources

Many useful resources related to Timers are provided

on the main product page of the Microchip web site for

the devices listed in this data sheet. This product page,

which can be accessed using this link, contains the

latest updates and additional information.

12.1.1 KEY RESOURCES

•Section 11. “Timers” (DS70362) in the

“dsPIC33E/PIC24E Family Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

 2009-2012 Microchip Technology Inc. DS70616G-page 273

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

12.2 Timer1 Control Register

R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0

TON(1)—TSIDL— — — — —

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 U-0

— TGATE TCKPS<1:0> — TSYNC(1)TCS(1)—

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 TON: Timer1 On bit(1)

1 = Starts 16-bit Timer1

0 = Stops 16-bit Timer1

bit 14 Unimplemented: Read as ‘0’

bit 13 TSIDL: Timer1 Stop in Idle Mode bit

1 = Discontinues module operation when device enters Idle mode

0 = Continues module operation in Idle mode

bit 12-7 Unimplemented: Read as ‘0’

bit 6 TGATE: Timer1 Gated Time Accumulation Enable bit

When TCS = 1:

This bit is ignored.

When TCS = 0:

1 = Gated time accumulation is enabled

0 = Gated time accumulation is disabled

bit 5-4 TCKPS<1:0> Timer1 Input Clock Prescale Select bits

11 = 1:256

10 = 1:64

01 = 1:8

00 = 1:1

bit 3 Unimplemented: Read as ‘0’

bit 2 TSYNC: Timer1 External Clock Input Synchronization Select bit(1)

When TCS = 1:

1 = Synchronizes external clock input

0 = Does not synchronize external clock input

When TCS = 0:

This bit is ignored.

bit 1 TCS: Timer1 Clock Source Select bit(1)

1 = External clock from T1CK pin (on the rising edge)

0 = Internal clock (FP)

bit 0 Unimplemented: Read as ‘0’

Note 1: When Timer1 is enabled in External Synchronous Counter mode (TCS = 1, TSYNC = 1, TON = 1), any

attempts by user software to write to the TMR1 register are ignored.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 274  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 275

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

13.0 TIMER2/3, TIMER4/5, TIMER6/7

AND TIMER8/9

The Timer2/3, Timer4/5, Timer6/7 and Timer8/9

modules are 32-bit timers, which can also be

configured as four independent 16-bit timers with

selectable operating modes.

As a 32-bit timer, Timer2/3, Timer4/5, Timer6/7 and

Timer8/9 operate in three modes:

• Two Independent 16-Bit Timers (e.g., Timer2 and

Timer3) with all 16-Bit Operating modes (except

Asynchronous Counter mode)

• Single 32-Bit Timer

• Single 32-Bit Synchronous Counter

They also support these features:

• Timer Gate Operation

• Selectable Prescaler Settings

• Timer Operation during Idle and Sleep modes

• Interrupt on a 32-Bit Period Register Match

• Time Base for Input Capture and Output Compare

Modules (Timer2 and Timer3 only)

• ADC1 Event Trigger (Timer2/3 only)

• ADC2 Event Trigger (Timer4/5 only)

Individually, all eight of the 16-bit timers can function as

synchronous timers or counters. They also offer the

features listed above, except for the event trigger; this

is implemented only with Timer2/3. The operating

modes and enabled features are determined by setting

the appropriate bit(s) in the T2CON, T3CON, T4CON,

T5CON, T6CON, T7CON, T8CON and T9CON

registers. T2CON, T4CON, T6CON and T8CON are

shown in generic form in Register 13-1. T3CON,

T5CON, T7CON and T9CON are shown in

For 32-bit timer/counter operation, Timer2, Timer4,

Timer6 or Timer8 is the least significant word; Timer3,

Timer5, Timer7 or Timer9 is the most significant word

of the 32-bit timers.

A block diagram for an example 32-bit timer pair is

shown Figure 13-3.

Note 1: This data sheet summarizes

the features of the

dsPIC33EPXXX(GP/MC/MU)806/810/814

and PIC24EPXXX(GP/GU)810/814 family

of devices. It is not intended to be a

comprehensive reference source. To

complement the information in this data

sheet, refer to Section 11. “Timers”

(DS70362) of the “dsPIC33E/PIC24E

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Note: For 32-bit operation, T3CON, T5CON,

T7CON and T9CON control bits are

ignored. Only T2CON, T4CON, T6CON

and T8CON control bits are used for setup

and control. Timer2, Timer4, Timer6 and

Timer8 clock and gate inputs are utilized

for the 32-bit timer modules, but an

interrupt is generated with the Timer3,

Timer5, Ttimer7 and Timer9 interrupt

flags.

Note: Only Timer2, 3, 4 and 5 can trigger a DMA

data transfer.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 276  2009-2012 Microchip Technology Inc.

FIGURE 13-1: TYPE B TIMERx BLOCK DIAGRAM (x = 2, 4, 6 AND 8)

FIGURE 13-2: TYPE C TIMERx BLOCK DIAGRAM (x = 3, 5, 7 AND 9)

TGATE

TCS

TMRx

PRx

TGATE

Set TxIF Flag

Equal

Reset

TxCK

TCKPS<1:0>

FP(1) Prescaler

(/n)

TCKPS<1:0>

Note 1: FP is the peripheral clock.

Latch

Data

CLK

TxCLK

Gate

Sync

Falling Edge

Detect

Sync

Prescaler

(/n) Comparator

TGATE

TCS

x1 Comparator

TGATE

Set TxIF Flag

Equal

Reset

TxCK

TCKPS<1:0>

Gate

Sync

FP(1)

Falling Edge

Detect

Prescaler

(/n)

TCKPS<1:0>

Note 1: FP is the peripheral clock.

2: The ADC trigger is available on TMR3 and TMR5 only.

Latch

Data

CLK

TxCLK

ADC Start of

Conversion Trigger(2)

Prescaler

(/n) Sync

TMRx

PRx

 2009-2012 Microchip Technology Inc. DS70616G-page 277

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 13-3: TYPE B/TYPE C TIMER PAIR BLOCK DIAGRAM (32-BIT TIMER)

13.1 Timer Resources

Many useful resources related to timers are provided

on the main product page of the Microchip web site for

the devices listed in this data sheet. This product page,

which can be accessed using this link, contains the

latest updates and additional information.

13.1.1 KEY RESOURCES

•Section 11. “Timers” (DS70362) in the

“dsPIC33E/PIC24E Family Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

TGATE

TCS

Comparator

TGATE

Set TyIF Flag

Equal

Reset

TxCK

TCKPS<1:0>

Gate

Sync

FP(1) Prescaler

(/n)

TCKPS<1:0>

Note 1: The ADC trigger is available only on the TMR3:TMR2 andTMR5:TMR4 32-bit timer pairs.

2: Timerx is a Type B timer (x = 2, 4, 6 and 8).

3: Timery is a Type C timer (x = 3, 5, 7 and 9).

Latch

Data

CLK

ADC

PRx

TMRyHLD

Data Bus<15:0>

mswlsw

Prescaler

(/n) Sync

Falling Edge

Detect

TMRyTMRx

PRy

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 278  2009-2012 Microchip Technology Inc.

13.2 Timerx/y Control Registers

R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0

TON —TSIDL— — — — —

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 U-0

— TGATE TCKPS<1:0> T32 —TCS

(1)—

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 TON: Timerx On bit

When T32 = 1:

1 = Starts 32-bit Timerx/y

0 = Stops 32-bit Timerx/y

When T32 = 0:

1 = Starts 16-bit Timerx

0 = Stops 16-bit Timerx

bit 14 Unimplemented: Read as ‘0’

bit 13 TSIDL: Timerx Stop in Idle Mode bit

1 = Discontinues module operation when device enters Idle mode

0 = Continues module operation in Idle mode

bit 12-7 Unimplemented: Read as ‘0’

bit 6 TGATE: Timerx Gated Time Accumulation Enable bit

When TCS = 1:

This bit is ignored.

When TCS = 0:

1 = Gated time accumulation is enabled

0 = Gated time accumulation is disabled

bit 5-4 TCKPS<1:0>: Timerx Input Clock Prescale Select bits

11 = 1:256

10 = 1:64

01 = 1:8

00 = 1:1

bit 3 T32: 32-Bit Timer Mode Select bit

1 = Timerx and Timery form a single 32-bit timer

0 = Timerx and Timery act as two 16-bit timers

bit 2 Unimplemented: Read as ‘0’

bit 1 TCS: Timerx Clock Source Select bit(1)

1 = External clock from TxCK pin (on the rising edge)

0 = Internal clock (FP)

bit 0 Unimplemented: Read as ‘0’

Note 1: The TxCK pin is not available on all timers. Refer to the “Pin Diagrams” section for the available pins.

 2009-2012 Microchip Technology Inc. DS70616G-page 279

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0

TON(1)—TSIDL

(2)— — — — —

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 U-0 U-0 R/W-0 U-0

—TGATE

(1)TCKPS<1:0>(1)——TCS

(1,3)—

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 TON: Timery On bit(1)

1 = Starts 16-bit Timery

0 = Stops 16-bit Timery

bit 14 Unimplemented: Read as ‘0’

bit 13 TSIDL: Timery Stop in Idle Mode bit(2)

1 = Discontinues module operation when device enters Idle mode

0 = Continues module operation in Idle mode

bit 12-7 Unimplemented: Read as ‘0’

bit 6 TGATE: Timery Gated Time Accumulation Enable bit(1)

When TCS = 1:

This bit is ignored.

When TCS = 0:

1 = Gated time accumulation is enabled

0 = Gated time accumulation is disabled

bit 5-4 TCKPS<1:0>: Timery Input Clock Prescale Select bits(1)

11 = 1:256

10 = 1:64

01 = 1:8

00 = 1:1

bit 3-2 Unimplemented: Read as ‘0’

bit 1 TCS: Timery Clock Source Select bit(1,3)

1 = External clock from TyCK pin (on the rising edge)

0 = Internal clock (FP)

bit 0 Unimplemented: Read as ‘0’

Note 1: When 32-bit operation is enabled (T2CON<3> = 1), these bits have no effect on Timery operation; all timer

functions are set through TxCON.

2: When 32-bit timer operation is enabled (T32 = 1) in the Timer Control register (TxCON<3>), the TSIDL bit

must be cleared to operate the 32-bit timer in Idle mode.

3: The TyCK pin is not available on all timers. Refer to the “Pin Diagrams” section for the available pins.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 280  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 281

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

14.0 INPUT CAPTURE The input capture module is useful in applications

requiring frequency (period) and pulse measurement.

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices support up to

16 input capture channels.

Key features of the input capture module include:

• Hardware-configurable for 32-bit operation in all

modes by cascading two adjacent modules

• Synchronous and Trigger modes of output

compare operation, with up to 30 user-selectable

Trigger/Sync sources available

• A 4-level FIFO buffer for capturing and holding

timer values for several events

• Configurable interrupt generation

• Up to six clock sources available for each module,

driving a separate internal 16-bit counter

FIGURE 14-1: INPUT CAPTURE MODULE BLOCK DIAGRAM

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this

data sheet, refer to Section 12. “Input

Capture” (DS70352) of the “dsPIC33E/

PIC24E Family Reference Manual”,

which is available from the Microchip web

site (www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information. Note: Only IC1, IC2, IC3 and IC4 can trigger a

DMA data transfer. If DMA data transfers

are required, the FIFO buffer size must be

set to ‘1’ (ICI<1:0> = 00).

ICxBUF

4-Level FIFO Buffer

ICx Pin

ICM<2:0>

Set ICxIF

Edge Detect Logic

ICI<1:0>

ICOV, ICBNE

Interrupt

Logic

System Bus

Prescaler

Counter

1:1/4/16

and

Clock Synchronizer

Event and

Trigger and

Sync Logic

Clock

Select

Trigger and

Sync Sources

ICTSEL<2:0>

SYNCSEL<4:0>

Trigger(1)

ICxTMR

Increment

Reset

Note 1: The Trigger/Sync source is enabled by default and is set to Timer3 as a source. This timer must be enabled for

proper ICx module operation or the Trigger/Sync source must be changed to another source option.

T1CLK

T5CLK

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 282  2009-2012 Microchip Technology Inc.

14.1 Input Capture Resources

Many useful resources related to input capture are pro-

vided on the main product page of the Microchip web

site for the devices listed in this data sheet. This product

page, which can be accessed using this link, contains

the latest updates and additional information.

14.1.1 KEY RESOURCES

•Section 12. “Input Capture” (DS70352) in the

“dsPIC33E/PIC24E Family Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

 2009-2012 Microchip Technology Inc. DS70616G-page 283

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

14.2 Input Capture Control Registers

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0

—— ICSIDL ICTSEL<2:0> — —

bit 15 bit 8

U-0 R/W-0 R/W-0 R/HC/HS-0 R/HC/HS-0 R/W-0 R/W-0 R/W-0

— ICI<1:0> ICOV ICBNE ICM<2:0>

bit 7 bit 0

Legend:

R = Readable bit HC = Hardware Clearable bit HS = Hardware Settable bit ‘0’ = Bit is cleared

-n = Value at POR W = Writable bit U = Unimplemented bit, read as ‘0’

bit 15-14 Unimplemented: Read as ‘0’

bit 13 ICSIDL: Input Capture Stop in Idle Control bit

1 = Input capture will Halt in CPU Idle mode

0 = Input capture will continue to operate in CPU Idle mode

bit 12-10 ICTSEL<12:10>: Input Capture Timer Select bits

111 = Peripheral clock (FP) is the clock source of the ICx

110 = Reserved

101 = Reserved

100 = Clock source of T1CLK is the clock source of the ICx (only the synchronous clock is supported)

011 = Clock source of T5CLK is the clock source of the ICx

010 = Clock source of T4CLK is the clock source of the ICx

001 = Clock source of T2CLK is the clock source of the ICx

000 = Clock source of T3CLK is the clock source of the ICx

bit 9-7 Unimplemented: Read as ‘0’

bit 6-5 ICI<1:0>: Number of Captures per Interrupt Select bits (this field is not used if ICM<2:0> = 001 or 111)

11 = Interrupt on every fourth capture event

10 = Interrupt on every third capture event

01 = Interrupt on every second capture event

00 = Interrupt on every capture event

bit 4 ICOV: Input Capture Overflow Status Flag bit (read-only)

1 = Input capture buffer overflow occurred

0 = No input capture buffer overflow occurred

bit 3 ICBNE: Input Capture Buffer Not Empty Status bit (read-only)

1 = Input capture buffer is not empty, at least one more capture value can be read

0 = Input capture buffer is empty

bit 2-0 ICM<2:0>: Input Capture Mode Select bits

111 = Input capture functions as interrupt pin only in CPU Sleep and Idle modes (rising edge detect

only, all other control bits are not applicable)

110 = Unused (module disabled)

101 = Capture mode, every 16th rising edge (Prescaler Capture mode)

100 = Capture mode, every 4th rising edge (Prescaler Capture mode)

011 = Capture mode, every rising edge (Simple Capture mode)

010 = Capture mode, every falling edge (Simple Capture mode)

001 = Capture mode, every edge rising and falling (Edge Detect mode (ICI<1:0>) is not used in this mode)

000 = Input capture module is turned off

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 284  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0

— — — — — — —IC32

bit 15 bit 8

R/W-0 R/W/HS-0 U-0 R/W-0 R/W-1 R/W-1 R/W-0 R/W-1

ICTRIG(2)TRIGSTAT(3)— SYNCSEL<4:0>(4)

bit 7 bit 0

Legend:

R = Readable bit HS = Set by Hardware ‘0’ = Bit is cleared

-n = Value at POR W = Writable bit U = Unimplemented bit, read as ‘0’

bit 15-9 Unimplemented: Read as ‘0’

bit 8 IC32: 32-Bit Timer Mode Select bit (Cascade mode)

1 = ODD IC and EVEN IC form a single 32-bit input capture module(1)

0 = Cascade module operation is disabled

bit 7

ICTRIG:

Trigger Operation Select bit(2)

= Input source is used to trigger the input capture timer (Trigger mode)

0 = Input source is used to synchronize the input capture timer to a timer of another module

(Synchronization mode)

bit 6 TRIGSTAT: Timer Trigger Status bit(3)

1 = ICxTMR has been triggered and is running

0 = ICxTMR has not been triggered and is being held clear

bit 5 Unimplemented: Read as ‘0’

Note 1: The IC32 bit in both the ODD and EVEN IC must be set to enable Cascade mode.

2: The input source is selected by the SYNCSEL<4:0> bits of the ICxCON2 register.

3: This bit is set by the selected input source (selected by the SYNCSEL<4:0> bits); it can be read, set and

cleared in software.

4: Do not use the ICx module as its own Sync or Trigger source.

5: This option should only be selected as a trigger source and not as a synchronization source.

 2009-2012 Microchip Technology Inc. DS70616G-page 285

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

bit 4-0 SYNCSEL<4:0>: Input Source Select for Synchronization and Trigger Operation bits(4)

11111 = No Sync or Trigger source for ICx

11110 = No Sync or Trigger source for ICx

11101 = No Sync or Trigger source for ICx

11100 = Reserved

11011 = ADC1 module synchronizes or triggers ICx(5)

11010 = CMP3 module synchronizes or triggers ICx(5)

11001 = CMP2 module synchronizes or triggers ICx(5)

11000 = CMP1 module synchronizes or triggers ICx(5)

10111 = IC8 module synchronizes or triggers ICx

10110 = IC7 module synchronizes or triggers ICx

10101 = IC6 module synchronizes or triggers ICx

10100 = IC5 module synchronizes or triggers ICx

10011 = IC4 module synchronizes or triggers ICx

10010 = IC3 module synchronizes or triggers ICx

10001 = IC2 module synchronizes or triggers ICx

10000 = IC1 module synchronizes or triggers ICx

01111 = Timer5 synchronizes or triggers ICx

01110 = Timer4 synchronizes or triggers ICx

01101 = Timer3 synchronizes or triggers ICx (default)

01100 = Timer2 synchronizes or triggers ICx

01011 = Timer1 synchronizes or triggers ICx

01010 = No Sync or Trigger source for ICx

01001 = OC9 module synchronizes or triggers ICx

01000 = OC8 module synchronizes or triggers ICx

00111 = OC7 module synchronizes or triggers ICx

00110 = OC6 module synchronizes or triggers ICx

00101 = OC5 module synchronizes or triggers ICx

00100 = OC4 module synchronizes or triggers ICx

00011 = OC3 module synchronizes or triggers ICx

00010 = OC2 module synchronizes or triggers ICx

00001 = OC1 module synchronizes or triggers ICx

00000 = No Sync or Trigger source for ICx

Note 1: The IC32 bit in both the ODD and EVEN IC must be set to enable Cascade mode.

2: The input source is selected by the SYNCSEL<4:0> bits of the ICxCON2 register.

3: This bit is set by the selected input source (selected by the SYNCSEL<4:0> bits); it can be read, set and

cleared in software.

4: Do not use the ICx module as its own Sync or Trigger source.

5: This option should only be selected as a trigger source and not as a synchronization source.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 286  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 287

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

15.0 OUTPUT COMPARE The output compare module can select one of eight

available clock sources for its time base. The module

compares the value of the timer with the value of one or

two Compare registers, depending on the operating

mode selected. The state of the output pin changes

when the timer value matches the Compare register

value. The output compare module generates either a

single output pulse, or a sequence of output pulses, by

changing the state of the output pin on the compare

match events. The output compare module can also

generate interrupts on compare match events.

FIGURE 15-1: OUTPUT COMPARE MODULE BLOCK DIAGRAM

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this

data sheet, refer to Section 13. “Output

Compare” (DS70358) of the “dsPIC33E/

PIC24E Family Reference Manual”,

which is available from the Microchip web

site (www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Note 1: Only OC1, OC2, OC3 and OC4 can trigger

a DMA data transfer.

2: See Section 13. “Output Compare”

(DS70358) in the “dsPIC33E/PIC24E

Family Reference Manual” for OCxR and

OCxRS register restrictions.

OCxR Buffer

Comparator

OCxTMR

OCxCON1

OCxCON2

OC Output and

OCx Interrupt

OCx Pin

OCxRS Buffer

Comparator

Fault Logic

Match

Trigger and

Sync Logic

Clock

Select

Increment

Reset

Trigger and

Sync Sources

Reset

Match Event OCFA

OCxR

OCxRS

Event

Rollover

Rollover/Reset

OCx Synchronization/Trigger Event

OCFB

OCFC

SYNCSEL<4:0>

Trigger

(1)

Note 1: The Trigger/Sync source is enabled by default and is set to Timer2 as a source. This timer must be enabled for

proper OCx module operation or the Trigger/Sync source must be changed to another source option.

T1CLK

T5CLK

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 288  2009-2012 Microchip Technology Inc.

15.1 Output Compare Resources

Many useful resources related to output compare are

provided on the main product page of the Microchip

web site for the devices listed in this data sheet. This

product page, which can be accessed using this link,

contains the latest updates and additional information.

15.1.1 KEY RESOURCES

•Section 13. “Output Compare” (DS70358) in

the “dsPIC33E/PIC24E Family Reference

Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

 2009-2012 Microchip Technology Inc. DS70616G-page 289

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

15.2 Output Compare Control Registers

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— OCSIDL OCTSEL<2:0> ENFLTC ENFLTB

bit 15 bit 8

R/W-0 R/W-0, HSC R/W-0, HSC R/W-0, HSC R/W-0 R/W-0 R/W-0 R/W-0

ENFLTA OCFLTC OCFLTB OCFLTA TRIGMODE OCM<2:0>

bit 7 bit 0

Legend: HCS = Hardware Settable/Clearable bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13 OCSIDL: Stop Output Compare x in Idle Mode Control bit

1 = Output Compare x Halts in CPU Idle mode

0 = Output Compare x continues to operate in CPU Idle mode

bit 12-10 OCTSEL<2:0>: Output Compare x Clock Select bits

111 = Peripheral clock (FP)

110 = Reserved

101 = Reserved

100 = Clock source of T1CLK is the clock source of OCx (only the synchronous clock is supported)

011 = Clock source of T5CLK is the clock source of OCx

010 = Clock source of T4CLK is the clock source of OCx

001 = Clock source of T3CLK is the clock source of OCx

000 = Clock source of T2CLK is the clock source of OCx

bit 9 ENFLTC: Fault C Input Enable bit

1 = Output Compare Fault C input (OCFC) is enabled

0 = Output Compare Fault C input (OCFC) is disabled

bit 8 ENFLTB: Fault B Input Enable bit

1 = Output Compare Fault B input (OCFB) is enabled

0 = Output Compare Fault B input (OCFB) is disabled

bit 7 ENFLTA: Fault A Input Enable bit

1 = Output Compare Fault A input (OCFA) is enabled

0 = Output Compare Fault A input (OCFA) is disabled

bit 6 OCFLTC: PWM Fault C Condition Status bit

1 = PWM Fault C condition on OCFC pin has occurred

0 = No PWM Fault C condition on OCFC pin has occurred

bit 5 OCFLTB: PWM Fault B Condition Status bit

1 = PWM Fault B condition on OCFB pin has occurred

0 = No PWM Fault B condition on OCFB pin has occurred

bit 4 OCFLTA: PWM Fault A Condition Status bit

1 = PWM Fault A condition on OCFA pin has occurred

0 = No PWM Fault A condition on OCFA pin has occurred

bit 3 TRIGMODE: Trigger Status Mode Select bit

1 = TRIGSTAT (OCxCON2<6>) is cleared when OCxRS = OCxTMR or in software

0 = TRIGSTAT is cleared only by software

Note 1: OCxR and OCxRS are double-buffered in PWM mode only.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 290  2009-2012 Microchip Technology Inc.

bit 2-0 OCM<2:0>: Output Compare Mode Select bits

111 = Center-Aligned PWM mode: Output set high when OCxTMR = OCxR and set low when

OCxTMR = OCxRS(1)

110 = Edge-Aligned PWM mode: Output set high when OCxTMR = 0 and set low when

OCxTMR = OCxR(1)

101 = Double Compare Continuous Pulse mode: Initializes OCx pin low, toggles OCx state continuously

on alternate matches of OCxR and OCxRS

100 = Double Compare Single-Shot mode: Initializes OCx pin low, toggles OCx state on matches of

OCxR and OCxRS for one cycle

011 = Single Compare mode: Compares events with OCxR, continuously toggles OCx pin

010 = Single Compare Single-Shot mode: Initializes OCx pin high, compares event with OCxR, forces

OCx pin low

001 = Single Compare Single-Shot mode: Initializes OCx pin low, compares event with OCxR, forces

OCx pin high

000 = Output compare channel is disabled

Note 1: OCxR and OCxRS are double-buffered in PWM mode only.

 2009-2012 Microchip Technology Inc. DS70616G-page 291

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 R/W-0

FLTMD FLTOUT FLTTRIEN OCINV — — —OC32

bit 15 bit 8

R/W-0 R/W-0 HS R/W-0 R/W-0 R/W-1 R/W-1 R/W-0 R/W-0

OCTRIG TRIGSTAT OCTRIS SYNCSEL<4:0>

bit 7 bit 0

Legend: HS = Hardware Settable bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 FLTMD: Fault Mode Select bit

1 = Fault mode is maintained until the Fault source is removed; the corresponding OCFLTx bit is

cleared in software and a new PWM period starts

0 = Fault mode is maintained until the Fault source is removed and a new PWM period starts

bit 14 FLTOUT: Fault Out bit

1 = PWM output is driven high on a Fault

0 = PWM output is driven low on a Fault

bit 13 FLTTRIEN: Fault Output State Select bit

1 = OCx pin is tri-stated on Fault condition

0 = OCx pin I/O state defined by FLTOUT bit on Fault condition

bit 12 OCINV: OCMP Invert bit

1 = OCx output is inverted

0 = OCx output is not inverted

bit 11-9 Unimplemented: Read as ‘0’

bit 8 OC32: Cascade Two OCx Modules Enable bit (32-bit operation)

1 = Cascade module operation is enabled

0 = Cascade module operation is disabled

bit 7 OCTRIG: OCx Trigger/Sync Select bit

1 = Triggers OCx from source designated by SYNCSELx bits

0 = Synchronizes OCx with source designated by SYNCSELx bits

bit 6 TRIGSTAT: Timer Trigger Status bit

1 = Timer source has been triggered and is running

0 = Timer source has not been triggered and is being held clear

bit 5 OCTRIS: OCx Output Pin Direction Select bit

1 = OCx is tri-stated

0 = Output compare module drives the OCx pin

Note 1: Do not use the OCx module as its own Sync or Trigger source.

2: When the OCy module is turned OFF, it sends a trigger out signal. If the OCx module uses the OCy module

as a Trigger source, the OCy module must be unselected as a Trigger source prior to disabling it.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 292  2009-2012 Microchip Technology Inc.

bit 4-0 SYNCSEL<4:0>: Trigger/Synchronization Source Selection bits

11111 = No Sync or Trigger source for OCx

11110 = INT2 pin synchronizes or triggers OCx

11101 = INT1 pin synchronizes or triggers OCx

11100 = Reserved

11011 = ADC1 module synchronizes or triggers OCx

11010 = CMP3 module synchronizes or triggers OCx

11001 = CMP2 module synchronizes or triggers OCx

11000 = CMP1 module synchronizes or triggers OCx

10111 = IC8 module synchronizes or triggers OCx

10110 = IC7 module synchronizes or triggers OCx

10101 = IC6 module synchronizes or triggers OCx

10100 = IC5 module synchronizes or triggers OCx

10011 = IC4 module synchronizes or triggers OCx

10010 = IC3 module synchronizes or triggers OCx

10001 = IC2 module synchronizes or triggers OCx

10000 = IC1 module synchronizes or triggers OCx

01111 = Timer5 synchronizes or triggers OCx

01110 = Timer4 synchronizes or triggers OCx

01101 = Timer3 synchronizes or triggers OCx

01100 = Timer2 synchronizes or triggers OCx (default)

01011 = Timer1 synchronizes or triggers OCx

01010 = No Sync or Trigger source for OCx

01001 = OC9 module synchronizes or triggers OCx(1,2)

01000 = OC8 module synchronizes or triggers OCx(1,2)

00111 = OC7 module synchronizes or triggers OCx(1,2)

00110 = OC6 module synchronizes or triggers OCx(1,2)

00101 = OC5 module synchronizes or triggers OCx(1,2)

00100 = OC4 module synchronizes or triggers OCx(1,2)

00011 = OC3 module synchronizes or triggers OCx(1,2)

00010 = OC2 module synchronizes or triggers OCx(1,2)

00001 = OC1 module synchronizes or triggers OCx(1,2)

00000 = No Sync or Trigger source for OCx

Note 1: Do not use the OCx module as its own Sync or Trigger source.

2: When the OCy module is turned OFF, it sends a trigger out signal. If the OCx module uses the OCy module

as a Trigger source, the OCy module must be unselected as a Trigger source prior to disabling it.

 2009-2012 Microchip Technology Inc. DS70616G-page 293

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

16.0 HIGH-SPEED PWM MODULE

(dsPIC33EPXXX(MC/MU)8XX

DEVICES ONLY)

The dsPIC33EPXXX(MC/MU)806/810/814 devices

support a dedicated Pulse-Width Modulation (PWM)

module with up to 14 outputs.

The high-speed PWM module consists of the following

major features:

• Two master time base modules with Special

Event Triggers

• PWM module input clock prescaler

• Two synchronization inputs

• Two synchronization outputs

• Up to seven PWM generators

• Two PWM outputs per generator (PWMxH and

PWMxL)

• Individual period, duty cycle and phase shift for

each PWM output

• Period, duty cycle, phase shift and dead-time

resolution of 8.32 ns

• Immediate update mode for PWM period, duty

cycle and phase shift

• Independent Fault and current-limited inputs for

each PWM

• Cycle-by-Cycle and Latched Fault modes

• PWM time-base capture upon current limit

• Seven Fault inputs and three comparator outputs

available for Faults and current limits

• Programmable ADC trigger with interrupt for each

PWM pair

• Complementary PWM outputs

• Push-Pull PWM outputs

• Redundant PWM outputs

• Edge-Aligned PWM mode

• Center-Aligned PWM mode

• Variable Phase PWM mode

• Multi-Phase PWM mode

• Fixed Off Time PWM mode

• Current-Limit PWM mode

• Current Reset PWM mode

• PWMxH and PWMxL output override control

• PWMxH and PWMxL output pin swapping

• Chopping mode (also known as Gated mode)

• Dead-time insertion

• Dead-time compensation

• Enhanced Leading-Edge Blanking (LEB)

• 8 mA PWM pin output drive

The high-speed PWM module contains up to seven

PWM generators. Each PWM generator provides two

PWM outputs: PWMxH and PWMxL. Two master time

base generators provide a synchronous signal as a

common time base to synchronize the various PWM

outputs. Each generator can operate independently or

in synchronization with either of the two master time

bases. The individual PWM outputs are available on

the output pins of the device. The input Fault signals

and current-limited signals, when enabled, can monitor

and protect the system by placing the PWM outputs

into a known “safe” state.

Each PWM can generate a trigger to the ADC module

to sample the analog signal at a specific instance dur-

ing the PWM period. In addition, the high-speed PWM

module also generates two Special Event Triggers to

the ADC module based on the two master time bases.

The high-speed PWM module can synchronize itself

with an external signal or can act as a synchronizing

source to any external device. The SYNCI1 and

SYNCI2 pins are the input pins, which can synchronize

the high-speed PWM module with an external signal.

The SYNCO1 and SYNCO2 pins are output pins that

provides a synchronous signal to an external device.

Figure 16-1 illustrates an architectural overview of the

high-speed PWM module and its interconnection with

the CPU and other peripherals.

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not

intended to be a comprehensive

reference source. To complement the

information in this data sheet, refer to

Section 14. “High-Speed PWM”

(DS70645) of the “dsPIC33E/PIC24E

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Note: Duty cycle, dead time, phase shift and

frequency resolution is 16.64 ns in

Center-Aligned PWM mode.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 294  2009-2012 Microchip Technology Inc.

FIGURE 16-1: HIGH-SPEED PWM MODULE ARCHITECTURAL OVERVIEW

CPU

Primary and Secondary

PWM

Generator 1

PWM

Generator 2

PWM

Generator 6

PWM

Generator 7

SYNCI1/SYNCI2

SYNCO1/SYNCO2

PWM1H

PWM1L

PWM1 Interrupt

PWM2H

PWM2L

PWM2 Interrupt

PWM6H

PWM6L

PWM6 Interrupt

PWM7H

PWM7L

PWM7 Interrupt

Synchronization Signal

Data Bus

ADC Module

FLT1-FLT7 and

Synchronization Signal

Primary Trigger

Primary Special

DTCMP1-DTCMP7

Fault, Current-Limit

and Dead-Time Compensation

PWM3 through PWM5

Secondary Special

Event Trigger

Event Trigger Fault, Current-Limit

and Dead-Time Compensation

Master Time Base

Fault, Current-Limit

and Dead-Time Compensation

Fault, Current-Limit

and Dead-Time Compensation

FOSC

 2009-2012 Microchip Technology Inc. DS70616G-page 295

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 16-2: HIGH-SPEED PWM MODULE REGISTER INTERCONNECTION DIAGRAM

MUX

PTMRx

PDCx

PWMCONx TRGCONx

PTCON, PTCON2

IOCONx

DTRx

PWMxL

PWMxH

FLT1

PWM1L

PWM1H

FCLCONx

PHASEx

LEBCONx

MUX

STMRx

SDCx

SPHASEx ALTDTRx

PWMCAPx

User Override Logic

Current-Limit

PWM Output Mode

Control Logic

Fault and

Current-Limit

Logic

PWM Generator 1

FLTx

PWM Generator 2 – PWM Generator 7

Interrupt

Logic

ADC Trigger

Module Control and Timing

Duty Cycle Register

Synchronization Synchronization

Master PeriodMaster Period

Master Duty CycleMaster Duty Cycle

Secondary PWM

SYNCI2

SYNCI1

SYNCO1

SEVTCMP

Comparator Special Event Trigger

Special Event

Postscaler

PTPER

PMTMR Primary Master Time Base

Master Time Base Counter

Special Event Compare Trigger

Clock

Prescaler

Comparator

16-Bit Data Bus

TRIGx Fault Override Logic

Override Logic

SYNCO2

SEVTCMP

Comparator Special Event Trigger

Special Event

Postscaler

PTPER

PMTMR Secondary Master Time Base

Master Time Base Counter

Special Event Compare Trigger

Comparator

Clock

Prescaler

DTCMPx

DTCMP1

FOSC

MDC

Dead-Time

Logic

Control

Logic

Comparator

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 296  2009-2012 Microchip Technology Inc.

16.1 PWM Resources

Many useful resources related to the high-speed PWM

are provided on the main product page of the Microchip

web site for the devices listed in this data sheet. This

product page, which can be accessed using this link,

contains the latest updates and additional information.

16.1.1 KEY RESOURCES

•Section 11. “High-Speed PWM” (DS70645) in

the “dsPIC33E/PIC24E Family Reference

Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

 2009-2012 Microchip Technology Inc. DS70616G-page 297

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

16.2 PWM Control Registers

R/W-0 U-0 R/W-0 HSC-0 R/W-0 R/W-0 R/W-0 R/W-0

PTEN — PTSIDL SESTAT SEIEN EIPU(1)SYNCPOL(1)SYNCOEN(1)

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SYNCEN(1)SYNCSRC<2:0>(1)SEVTPS<3:0>(1)

bit 7 bit 0

Legend: HSC = Hardware Settable/Clearable bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 PTEN: PWM Module Enable bit

1 = PWM module is enabled

0 = PWM module is disabled

bit 14 Unimplemented: Read as ‘0’

bit 13 PTSIDL: PWM Time Base Stop in Idle Mode bit

1 = PWM time base halts in CPU Idle mode

0 = PWM time base runs in CPU Idle mode

bit 12 SESTAT: Special Event Interrupt Status bit

1 = Special event interrupt is pending

0 = Special event interrupt is not pending

bit 11 SEIEN: Special Event Interrupt Enable bit

1 = Special event interrupt is enabled

0 = Special event interrupt is disabled

bit 10 EIPU: Enable Immediate Period Updates bit(1)

1 = Active Period register is updated immediately

0 = Active Period register updates occur on PWM cycle boundaries

bit 9 SYNCPOL: Synchronize Input and Output Polarity bit(1)

1 = SYNCIx/SYNCO polarity is inverted (active-low)

0 = SYNCIx/SYNCO is active-high

bit 8 SYNCOEN: Primary Time Base Sync Enable bit(1)

1 = SYNCO output is enabled

0 = SYNCO output is disabled

bit 7 SYNCEN: External Time Base Synchronization Enable bit(1)

1 = External synchronization of primary time base is enabled

0 = External synchronization of primary time base is disabled

Note 1: These bits should be changed only when PTEN = 0. In addition, when using the SYNCIx feature, the user

application must program the Period register with a value that is slightly larger than the expected period of

the external synchronization input signal.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 298  2009-2012 Microchip Technology Inc.

bit 6-4 SYNCSRC<2:0>: Synchronous Source Selection bits(1)

111 = Reserved

•

010 = Reserved

001 = SYNCI2

000 = SYNCI1

bit 3-0 SEVTPS<3:0>: PWM Special Event Trigger Output Postscaler Select bits(1)

1111 = 1:16 Postscaler generates Special Event Trigger on every sixteenth compare match event

•

0001 = 1:2 Postscaler generates Special Event Trigger on every second compare match event

0000 = 1:1 Postscaler generates Special Event Trigger on every compare match event

Note 1: These bits should be changed only when PTEN = 0. In addition, when using the SYNCIx feature, the user

application must program the Period register with a value that is slightly larger than the expected period of

the external synchronization input signal.

 2009-2012 Microchip Technology Inc. DS70616G-page 299

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0

— — — — — PCLKDIV<2:0>(1)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-3 Unimplemented: Read as ‘0’

bit 2-0 PCLKDIV<2:0>: PWM Input Clock Prescaler (Divider) Select bits(1)

111 = Reserved

110 = Divide-by-64

101 = Divide-by-32

100 = Divide-by-16

011 = Divide-by-8

010 = Divide-by-4

001 = Divide-by-2

000 = Divide-by-1, maximum PWM timing resolution (power-on default)

Note 1: These bits should be changed only when PTEN = 0. Changing the clock selection during operation will

yield unpredictable results.

R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1

PTPER<15:8>

bit 15 bit 8

R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-0 R/W-0 R/W-0

PTPER<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 PTPER<15:0>: Primary Master Time Base (PMTMR) Period Value bits

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 300  2009-2012 Microchip Technology Inc.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SEVTCMP<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SEVTCMP<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 SEVTCMP<15:0>: Special Event Compare Count Value bits

 2009-2012 Microchip Technology Inc. DS70616G-page 301

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 HSC-0 R/W-0 R/W-0 R/W-0 R/W-0

— — — SESTAT SEIEN EIPU(1)SYNCPOL SYNCOEN

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SYNCEN SYNCSRC<2:0> SEVTPS<3:0>

bit 7 bit 0

Legend: HSC = Set or Cleared in Hardware

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-13 Unimplemented: Read as ‘0’

bit 12 SESTAT: Special Event Interrupt Status bit

1 = Secondary special event interrupt is pending

0 = Secondary special event interrupt is not pending

bit 11 SEIEN: Special Event Interrupt Enable bit

1 = Secondary special event interrupt is enabled

0 = Secondary special event interrupt is disabled

bit 10 EIPU: Enable Immediate Period Updates bit(1)

1 = Active Secondary Period register is updated immediately

0 = Active Secondary Period register updates occur on PWM cycle boundaries

bit 9 SYNCPOL: Synchronize Input and Output Polarity bit

1 = The falling edge of SYNCIN resets the SMTMR; SYNCO2 output is active-low

0 = The rising edge of SYNCIN resets the SMTMR; SYNCO2 output is active-high

bit 8 SYNCOEN: Secondary Master Time Base Synchronization Enable bit

1 = SYNCO2 output is enabled

0 = SYNCO2 output is disabled

bit 7 SYNCEN: External Secondary Master Time Base Synchronization Enable bit

1 = External synchronization of secondary time base is enabled

0 = External synchronization of secondary time base is disabled

bit 6-4 SYNCSRC<2:0>: Secondary Time Base Synchronization Source Selection bits

111 = Reserved

•

010 = Reserved

001 = SYNCI2

000 = SYNCI1

bit 3-0 SEVTPS<3:0>: PWM Secondary Special Event Trigger Output Postscaler Select bits

1111 = 1:16 Postcale

•

0001 = 1:2 Postcale

0000 = 1:1 Postscale

Note 1: This bit only applies to the secondary master time base period.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 302  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0

— — — — — PCLKDIV<2:0>(1)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-3 Unimplemented: Read as ‘0’

bit 2-0 PCLKDIV<2:0>: PWM Input Clock Prescaler (Divider) Select bits(1)

111 = Reserved

110 = Divide-by-64

101 = Divide-by-32

100 = Divide-by-16

011 = Divide-by-8

010 = Divide-by-4

001 = Divide-by-2

000 = Divide-by-1, maximum PWM timing resolution (power-on default)

Note 1: These bits should be changed only when PTEN = 0. Changing the clock selection during operation will

yield unpredictable results.

R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1

STPER<15:8>

bit 15 bit 8

R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-0 R/W-0 R/W-0

STPER<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 STPER<15:0>: Secondary Master Time Base (PMTMR) Period Value bits

 2009-2012 Microchip Technology Inc. DS70616G-page 303

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SSEVTCMP<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SSEVTCMP<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 SSEVTCMP<15:0>: Special Event Compare Count Value bits

R/W-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0

CHPCLKEN — — — — —CHOPCLK<9:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

CHOPCLK<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 CHPCLKEN: Enable Chop Clock Generator bit

1 = Chop clock generator is enabled

0 = Chop clock generator is disabled

bit 14-10 Unimplemented: Read as ‘0’

bit 9-0 CHOPCLK<9:0>: Chop Clock Divider bits

The frequency of the chop clock signal is given by the following expression:

Chop Frequency = FPWM/(CHOP<9:0> + 1)

Where, FPWM is FP divided by the value based on the PCLKDIV settings.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 304  2009-2012 Microchip Technology Inc.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

MDC<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

MDC<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 MDC<15:0>: Master PWM Duty Cycle Value bits

 2009-2012 Microchip Technology Inc. DS70616G-page 305

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

HSC-0 HSC-0 HSC-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

FLTSTAT(1)CLSTAT(1)TRGSTAT FLTIEN CLIEN TRGIEN ITB(2)MDCS(2)

bit 15 bit 8

R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0

DTC<1:0> DTCP(3)—MTBSCAM

(2,4)XPRES(5)IUE(2)

bit 7 bit 0

Legend: HSC = Set or Cleared in Hardware

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 FLTSTAT: Fault Interrupt Status bit(1)

1 = Fault interrupt is pending

0 = No Fault interrupt is pending

This bit is cleared by setting FLTIEN = 0.

bit 14 CLSTAT: Current-Limit Interrupt Status bit(1)

1 = Current-limit interrupt is pending

0 = No current-limit interrupt is pending

This bit is cleared by setting CLIEN = 0.

bit 13 TRGSTAT: Trigger Interrupt Status bit

1 = Trigger interrupt is pending

0 = No trigger interrupt is pending

This bit is cleared by setting TRGIEN = 0.

bit 12 FLTIEN: Fault Interrupt Enable bit

1 = Fault interrupt is enabled

0 = Fault interrupt is disabled and FLTSTAT bit is cleared

bit 11 CLIEN: Current-Limit Interrupt Enable bit

1 = Current-limit interrupt is enabled

0 = Current-limit interrupt is disabled and CLSTAT bit is cleared

bit 10 TRGIEN: Trigger Interrupt Enable bit

1 = A trigger event generates an interrupt request

0 = Trigger event interrupts are disabled and TRGSTAT bit is cleared

bit 9 ITB: Independent Time Base Mode bit(2)

1 = PHASEx/SPHASEx registers provide time base period for this PWM generator

0 = PTPER register provides timing for this PWM generator

bit 8 MDCS: Master Duty Cycle Register Select bit(2)

1 = MDC register provides duty cycle information for this PWM generator

0 = PDCx and SDCx registers provide duty cycle information for this PWM generator

Note 1: Software must clear the interrupt status here and in the corresponding IFS bit in the interrupt controller.

2: These bits should not be changed after the PWM is enabled (PTEN = 1).

3: DTC<1:0> = 11 for DTCP to be effective; otherwise, DTCP is ignored.

4: The Independent Time Base (ITB = 1) mode must be enabled to use Center-Aligned mode. If ITB = 0, the

CAM bit is ignored.

5: To operate in External Period Reset mode, the ITB bit must be ‘1’ and the CLMOD bit in the FCLCONx

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 306  2009-2012 Microchip Technology Inc.

bit 7-6 DTC<1:0>: Dead-Time Control bits

11 = Dead-Time Compensation mode

10 = Dead-time function is disabled

01 = Negative dead time actively applied for Complementary Output mode

00 = Positive dead time actively applied for all output modes

bit 5 DTCP: Dead-Time Compensation Polarity bit(3)

When set to ‘1’:

If DTCMPx = 0, PWMxL is shortened and PWMxH is lengthened.

If DTCMPx = 1, PWMxH is shortened and PWMxL is lengthened.

When set to ‘0’:

If DTCMPx = 0, PWMxH is shortened and PWMxL is lengthened.

If DTCMPx = 1, PWMxL is shortened and PWMxH is lengthened.

bit 4 Unimplemented: Read as ‘0’

bit 3 MTBS: Master Time Base Select bit

1 = PWM generator uses the secondary master time base for synchronization and as the clock source

for the PWM generation logic (if secondary time base is available)

0 = PWM generator uses the primary master time base for synchronization and as the clock source

for the PWM generation logic

bit 2 CAM: Center-Aligned Mode Enable bit(2,4)

1 = Center-Aligned mode is enabled

0 = Edge-Aligned mode is enabled

bit 1 XPRES: External PWM Reset Control bit(5)

1 = Current-limit source resets the time base for this PWM generator if it is in Independent Time Base

mode

0 = External pins do not affect PWM time base

bit 0 IUE: Immediate Update Enable bit(2)

1 = Updates to the active MDC/PDCx/SDCx registers are immediate

0 = Updates to the active PDCx registers are synchronized to the PWM time base

Note 1: Software must clear the interrupt status here and in the corresponding IFS bit in the interrupt controller.

2: These bits should not be changed after the PWM is enabled (PTEN = 1).

3: DTC<1:0> = 11 for DTCP to be effective; otherwise, DTCP is ignored.

4: The Independent Time Base (ITB = 1) mode must be enabled to use Center-Aligned mode. If ITB = 0, the

CAM bit is ignored.

5: To operate in External Period Reset mode, the ITB bit must be ‘1’ and the CLMOD bit in the FCLCONx

 2009-2012 Microchip Technology Inc. DS70616G-page 307

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PDCx<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PDCx<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 PDCx<15:0>: PWM Generator # Duty Cycle Value bits

Note 1: In Independent PWM mode, the PDCx register controls the PWMxH duty cycle only. In

the Complementary, Redundant and Push-Pull PWM modes, the PDCx register controls the duty cycle of

both the PWMxH and PWMxL.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SDCx<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SDCx<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 SDCx<15:0>: Secondary Duty Cycle bits for PWMxL Output Pin bits

Note 1: The SDCx register is used in Independent PWM mode only. When used in Independent PWM mode, the

SDCx register controls the PWMxL duty cycle.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 308  2009-2012 Microchip Technology Inc.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PHASEx<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PHASEx<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 PHASEx<15:0>: PWM Phase Shift Value or Independent Time Base Period for the PWM Generator bits

Note 1: If ITB (PWMCONx<9>) = 0, the following applies based on the mode of operation:

• Complementary, Redundant and Push-Pull Output mode (PMOD<1:0> (IOCON<11:10>) = 00, 01 or

10), PHASEx<15:0> = Phase shift value for PWMxH and PWMxL outputs.

• True Independent Output mode (PMOD<1:0> (IOCONx<11:10>) = 11), PHASEx<15:0> = Phase

shift value for PWMxH only.

2: If ITB (PWMCONx<9>) = 1, the following applies based on the mode of operation:

• Complementary, Redundant and Push-Pull Output mode (PMOD<1:0> (IOCONx<11:10>) = 00, 01

or 10), PHASEx<15:0> = Independent time base period value for PWMxH and PWMxL.

• True Independent Output mode (PMOD<1:0> (IOCONx<11:10>) = 11),

PHASEx<15:0> = Independent time base period value for PWMxH only.

 2009-2012 Microchip Technology Inc. DS70616G-page 309

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SPHASEx<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SPHASEx<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 SPHASEx<15:0>: Secondary Phase Offset bits for PWMxL Output Pin

(used in Independent PWM mode only)

Note 1: If ITB (PWMCONx<9>) = 0, the following applies based on the mode of operation:

• Complementary, Redundant and Push-Pull Output mode (PMOD<1:0> (IOCON<11:10>) = 00, 01 or

10), SPHASEx<15:0> = Not used.

• True Independent Output mode (PMOD<1:0> (IOCON<11:10>) = 11), SPHASEx<15:0> = Phase

shift value for PWMxL only.

2: If ITB (PWMCONx<9>) = 1, the following applies based on the mode of operation:

• Complementary, Redundant and Push-Pull Output mode (PMOD<1:0> (IOCON<11:10>) = 00, 01 or

10), SPHASEx<15:0> = Not used.

• True Independent Output mode (PMOD<1:0> (IOCON<11:10>) = 11),

SPHASEx<15:0> = Independent time base period value for PWMxL only.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 310  2009-2012 Microchip Technology Inc.

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— DTRx<13:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

DTRx<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-0 DTRx<13:0>: Unsigned 14-Bit Dead-Time Value for PWMx Dead-Time Unit bits

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— ALTDTRx<13:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

ALTDTRx<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-0 ALTDTRx<13:0>: Unsigned 14-Bit Dead-Time Value for PWMx Dead-Time Unit bits

 2009-2012 Microchip Technology Inc. DS70616G-page 311

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 U-0

TRGDIV<3:0> — — — —

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

——TRGSTRT<5:0>

(1)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 TRGDIV<3:0>: Trigger # Output Divider bits

1111 = Trigger output for every 16th trigger event

1110 = Trigger output for every 15th trigger event

1101 = Trigger output for every 14th trigger event

1100 = Trigger output for every 13th trigger event

1011 = Trigger output for every 12th trigger event

1010 = Trigger output for every 11th trigger event

1001 = Trigger output for every 10th trigger event

1000 = Trigger output for every 9th trigger event

0111 = Trigger output for every 8th trigger event

0110 = Trigger output for every 7th trigger event

0101 = Trigger output for every 6th trigger event

0100 = Trigger output for every 5th trigger event

0011 = Trigger output for every 4th trigger event

0010 = Trigger output for every 3rd trigger event

0001 = Trigger output for every 2nd trigger event

0000 = Trigger output for every trigger event

bit 11-6 Unimplemented: Read as ‘0’

bit 5-0 TRGSTRT<5:0>: Trigger Postscaler Start Enable Select bits(1)

111111 = Wait 63 PWM cycles before generating the first trigger event after the module is enabled

•

000010 = Wait 2 PWM cycles before generating the first trigger event after the module is enabled

000001 = Wait 1 PWM cycle before generating the first trigger event after the module is enabled

000000 = Wait 0 PWM cycles before generating the first trigger event after the module is enabled

Note 1: The secondary PWM generator cannot generate PWM trigger interrupts.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 312  2009-2012 Microchip Technology Inc.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PENH PENL POLH POLL PMOD<1:0>(1)OVRENH OVRENL

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

OVRDAT<1:0> FLTDAT<1:0> CLDAT<1:0> SWAP OSYNC

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 PENH: PWMxH Output Pin Ownership bit

1 = PWM module controls PWMxH pin

0 = GPIO module controls PWMxH pin

bit 14 PENL: PWMxL Output Pin Ownership bit

1 = PWM module controls PWMxL pin

0 = GPIO module controls PWMxL pin

bit 13 POLH: PWMxH Output Pin Polarity bit

1 = PWMxH pin is active-low

0 = PWMxH pin is active-high

bit 12 POLL: PWMxL Output Pin Polarity bit

1 = PWMxL pin is active-low

0 = PWMxL pin is active-high

bit 11-10 PMOD<1:0>: PWM # I/O Pin Mode bits(1)

11 = PWM I/O pin pair is in the True Independent Output mode

10 = PWM I/O pin pair is in the Push-Pull Output mode

01 = PWM I/O pin pair is in the Redundant Output mode

00 = PWM I/O pin pair is in the Complementary Output mode

bit 9 OVRENH: Override Enable for PWMxH Pin bit

1 = OVRDAT<1> controls output on PWMxH pin

0 = PWM generator controls PWMxH pin

bit 8 OVRENL: Override Enable for PWMxL Pin bit

1 = OVRDAT<0> controls output on PWMxL pin

0 = PWM generator controls PWMxL pin

bit 7-6 OVRDAT<1:0>: Data for PWMxH, PWMxL Pins if Override is Enabled bits

If OVERENH = 1, PWMxH is driven to the state specified by OVRDAT<1>.

If OVERENL = 1, PWMxL is driven to the state specified by OVRDAT<0>.

bit 5-4 FLTDAT<1:0>: Data for PWMxH and PWMxL Pins if FLTMOD is Enabled bits

IFLTMOD (FCLCONx<15>) = 0: Normal Fault mode:

If Fault is active, PWMxH is driven to the state specified by FLTDAT<1>.

If Fault is active, PWMxL is driven to the state specified by FLTDAT<0>.

IFLTMOD (FCLCONx<15>) = 1: Independent Fault mode:

If current limit is active, PWMxH is driven to the state specified by FLTDAT<1>.

If Fault is active, PWMxL is driven to the state specified by FLTDAT<0>.

Note 1: These bits should not be changed after the PWM module is enabled (PTEN = 1).

 2009-2012 Microchip Technology Inc. DS70616G-page 313

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

bit 3-2 CLDAT<1:0>: Data for PWMxH and PWMxL Pins if CLMOD is Enabled bits

IFLTMOD (FCLCONx<15>) = 0: Normal Fault mode:

If current limit is active, PWMxH is driven to the state specified by CLDAT<1>.

If current limit is active, PWMxL is driven to the state specified by CLDAT<0>.

IFLTMOD (FCLCONx<15>) = 1: Independent Fault mode:

The CLDAT<1:0> bits are ignored.

bit 1 SWAP: Swap PWMxH and PWMxL Pins bit

1 = PWMxH output signal is connected to PWMxL pins; PWMxL output signal is connected to

PWMxH pins

0 = PWMxH and PWMxL pins are mapped to their respective pins

bit 0 OSYNC: Output Override Synchronization bit

1 = Output overrides via the OVRDAT<1:0> bits are synchronized to the PWM time base

0 = Output overrides via the OVDDAT<1:0> bits occur on the next CPU clock boundary

Note 1: These bits should not be changed after the PWM module is enabled (PTEN = 1).

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 314  2009-2012 Microchip Technology Inc.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

TRGCMP<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

TRGCMP<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 TRGCMP<15:0>: PWM Primary Trigger Control Value bits

When the primary PWM functions in local time base, this register contains the compare values that

can trigger the ADC module.

 2009-2012 Microchip Technology Inc. DS70616G-page 315

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

IFLTMOD CLSRC<4:0>(2,3)CLPOL(1)CLMOD

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

FLTSRC<4:0>(2,3)FLTPOL(1)FLTMOD<1:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 IFLTMOD: Independent Fault Mode Enable bit

1 = Independent Fault mode: Current-limit input maps FLTDAT<1> to PWMxH output and Fault input

maps FLTDAT<0> to PWMxL output; the CLDAT<1:0> bits are not used for override functions

0 = Normal Fault mode: Current-Limit mode maps CLDAT<1:0> bits to the PWMxH and PWMxL

outputs; the PWM Fault mode maps FLTDAT<1:0> to the PWMxH and PWMxL outputs.

bit 14-10 CLSRC<4:0>: Current-Limit Control Signal Source Select for PWM Generator # bits(2,3)

11111 = Reserved

•

01001 = Reserved

01010 = Comparator 3

01001 = Comparator 2

01000 = Comparator 1

00111 = Reserved

00110 = Fault 7

00101 = Fault 6

00100 = Fault 5

00011 = Fault 4

00010 = Fault 3

00001 = Fault 2

00000 = Fault 1

bit 9 CLPOL: Current-Limit Polarity bit for PWM Generator #(1)

1 = The selected current-limit source is active-low

0 = The selected current-limit source is active-high

bit 8 CLMOD: Current-Limit Mode Enable bit for PWM Generator #

1 = Current-Limit mode is enabled

0 = Current-Limit mode is disabled

Note 1: These bits should be changed only when PTEN = 0. Changing the clock selection during operation will

yield unpredictable results.

2: When Independent Fault mode is enabled (IFLTMOD = 1) and Fault 1 is used for Fault mode

(FLTSRC<4:0> = 01000), the Current-Limit Control Source Select bits (CLSRC<4:0>) should be set to an

unused current-limit source to prevent the current-limit source from disabling both the PWMxH and

PWMxL outputs.

3: When Independent Fault mode is enabled (IFLTMOD = 1) and Fault 1 is used for Current-Limit mode

(CLSRC<4:0> = 01000), the Fault Control Source Select bits (FLTSRC<4:0>) should be set to an unused

Fault source to prevent Fault 1 from disabling both the PWMxL and PWMxH outputs.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 316  2009-2012 Microchip Technology Inc.

bit 7-3 FLTSRC<4:0>: Fault Control Signal Source Select bits for PWM Generator #(2,3)

11111 = Reserved

•

01011 = Reserved

01010 = Comparator 3

01001 = Comparator 2

01000 = Comparator 1

00111 = Reserved

00110 = Fault 7

00101 = Fault 6

00100 = Fault 5

00011 = Fault 4

00010 = Fault 3

00001 = Fault 2

00000 = Fault 1

bit 2 FLTPOL: Fault Polarity bit for PWM Generator #(1)

1 = The selected Fault source is active-low

0 = The selected Fault source is active-high

bit 1-0 FLTMOD<1:0>: Fault Mode bits for PWM Generator #

11 = Fault input is disabled

10 = Reserved

01 = The selected Fault source forces PWMxH, PWMxL pins to FLTDAT values (cycle)

00 = The selected Fault source forces PWMxH, PWMxL pins to FLTDAT values (latched condition)

Note 1: These bits should be changed only when PTEN = 0. Changing the clock selection during operation will

yield unpredictable results.

2: When Independent Fault mode is enabled (IFLTMOD = 1) and Fault 1 is used for Fault mode

(FLTSRC<4:0> = 01000), the Current-Limit Control Source Select bits (CLSRC<4:0>) should be set to an

unused current-limit source to prevent the current-limit source from disabling both the PWMxH and

PWMxL outputs.

3: When Independent Fault mode is enabled (IFLTMOD = 1) and Fault 1 is used for Current-Limit mode

(CLSRC<4:0> = 01000), the Fault Control Source Select bits (FLTSRC<4:0>) should be set to an unused

Fault source to prevent Fault 1 from disabling both the PWMxL and PWMxH outputs.

 2009-2012 Microchip Technology Inc. DS70616G-page 317

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0

PHR PHF PLR PLF FLTLEBEN CLLEBEN — —

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

——BCH

(1)BCL(1)BPHH BPHL BPLH BPLL

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 PHR: PWMxH Rising Edge Trigger Enable bit

1 = Rising edge of PWMxH will trigger Leading-Edge Blanking counter

0 = Leading-Edge Blanking ignores rising edge of PWMxH

bit 14 PHF: PWMxH Falling Edge Trigger Enable bit

1 = Falling edge of PWMxH will trigger Leading-Edge Blanking counter

0 = Leading-Edge Blanking ignores falling edge of PWMxH

bit 13 PLR: PWMxL Rising Edge Trigger Enable bit

1 = Rising edge of PWMxL will trigger Leading-Edge Blanking counter

0 = Leading-Edge Blanking ignores rising edge of PWMxL

bit 12 PLF: PWMxL Falling Edge Trigger Enable bit

1 = Falling edge of PWMxL will trigger Leading-Edge Blanking counter

0 = Leading-Edge Blanking ignores falling edge of PWMxL

bit 11 FLTLEBEN: Fault Input Leading-Edge Blanking Enable bit

1 = Leading-Edge Blanking is applied to selected Fault input

0 = Leading-Edge Blanking is not applied to selected Fault input

bit 10 CLLEBEN: Current-Limit Leading-Edge Blanking Enable bit

1 = Leading-Edge Blanking is applied to selected current-limit input

0 = Leading-Edge Blanking is not applied to selected current-limit input

bit 9-6 Unimplemented: Read as ‘0’

bit 5 BCH: Blanking in Selected Blanking Signal High Enable bit(1)

1 = State blanking (of current-limit and/or Fault input signals) when selected blanking signal is high

0 = No blanking when selected blanking signal is high

bit 4 BCL: Blanking in Selected Blanking Signal Low Enable bit(1)

1 = State blanking (of current-limit and/or Fault input signals) when selected blanking signal is low

0 = No blanking when selected blanking signal is low

bit 3 BPHH: Blanking in PWMxH High Enable bit

1 = State blanking (of current-limit and/or Fault input signals) when PWMxH output is high

0 = No blanking when PWMxH output is high

bit 2 BPHL: Blanking in PWMxH Low Enable bit

1 = State blanking (of current-limit and/or Fault input signals) when PWMxH output is low

0 = No blanking when PWMxH output is low

bit 1 BPLH: Blanking in PWMxL High Enable bit

1 = State blanking (of current-limit and/or Fault input signals) when PWMxL output is high

0 = No blanking when PWMxL output is high

bit 0 BPLL: Blanking in PWMxL Low Enable bit

1 = State blanking (of current-limit and/or Fault input signals) when PWMxL output is low

0 = No blanking when PWMxL output is low

Note 1: The blanking signal is selected via the BLANKSELx bits in the AUXCONx register.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 318  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0

— — — — LEB<11:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

LEB<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 Unimplemented: Read as ‘0’

bit 11-0 LEB<11:0>: Leading-Edge Blanking Delay for Current-Limit and Fault Inputs bits

 2009-2012 Microchip Technology Inc. DS70616G-page 319

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0

— — — — BLANKSEL<3:0>

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— CHOPSEL<3:0> CHOPHEN CHOPLEN

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 Unimplemented: Read as ‘0’

bit 11-8 BLANKSEL<3:0>: PWM State Blank Source Select bits

The selected state blank signal will block the current-limit and/or Fault input signals (if enabled via the

BCH and BCL bits in the LEBCONx register).

1001 = Reserved

1000 = Reserved

0111 = PWM7H selected as state blank source

0110 = PWM6H selected as state blank source

0101 = PWM5H selected as state blank source

0100 = PWM4H selected as state blank source

0011 = PWM3H selected as state blank source

0010 = PWM2H selected as state blank source

0001 = PWM1H selected as state blank source

0000 = No state blanking

bit 7-6 Unimplemented: Read as ‘0’

bit 5-2 CHOPSEL<3:0>: PWM Chop Clock Source Select bits

The selected signal will enable and disable (CHOP) the selected PWM outputs.

1001 = Reserved

1000 = Reserved

0111 = PWM7H selected as CHOP clock source

0110 = PWM6H selected as CHOP clock source

0101 = PWM5H selected as CHOP clock source

0100 = PWM4H selected as CHOP clock source

0011 = PWM3H selected as CHOP clock source

0010 = PWM2H selected as CHOP clock source

0001 = PWM1H selected as CHOP clock source

0000 = Chop clock generator selected as CHOP clock source

bit 1 CHOPHEN: PWMxH Output Chopping Enable bit

1 = PWMxH chopping function is enabled

0 = PWMxH chopping function is disabled

bit 0 CHOPLEN: PWMxL Output Chopping Enable bit

1 = PWMxL chopping function is enabled

0 = PWMxL chopping function is disabled

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 320  2009-2012 Microchip Technology Inc.

R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

PWMCAP<15:8>(1,2)

bit 15 bit 8

R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

PWMCAP<7:0>(1,2)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 PWMCAP<15:0>: Captured PWM Time Base Value bits(1,2)

The value in this register represents the captured PWM time base value when a leading edge is

detected on the current-limit input.

Note 1: The capture feature is only available on primary output (PWMxH).

2: This feature is active only after LEB processing on the current-limit input signal is complete.

 2009-2012 Microchip Technology Inc. DS70616G-page 321

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

17.0 QUADRATURE ENCODER

INTERFACE (QEI) MODULE

(dsPIC33EPXXX(MC/MU)8XX

DEVICES ONLY)

This chapter describes the Quadrature Encoder Inter-

face (QEI) module and associated operational modes.

The QEI module provides the interface to incremental

encoders for obtaining mechanical position data.

The operational features of the QEI module include:

• 32-Bit Position Counter

• 32-Bit Index Pulse Counter

• 32-Bit Interval Timer

• 16-Bit Velocity Counter

• 32-Bit Position Initialization/Capture/Compare

High Register

• 32-Bit Position Compare Low Register

• x4 Quadrature Count mode

• External Up/Down Count mode

• External Gated Count mode

• External Gated Timer mode

• Internal Timer mode

Figure 17-1 illustrates the QEI block diagram.

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this

data sheet, refer to Section 15.

“Quadrature Encoder Interface (QEI)”

(DS70601) of the “dsPIC33E/PIC24E

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Note: An ‘x’ used in the names of pins, control/

status bits and registers denotes a

particular Quadrature Encoder Interface

(QEI) module number (x = 1 or 2).

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 322  2009-2012 Microchip Technology Inc.

FIGURE 17-1: QEI BLOCK DIAGRAM

Quadrature

Decoder

Logic

CNTCMPx

QEBx

QEAx

INDXx

COUNT

DIR

FP COUNT

COUNT_EN

32-Bit Greater Than or Equal

Compare Register

32-Bit Index Counter Register

Digital

Filter

HOMEx FHOMEx

Data Bus Data Bus

COUNT_EN

CNT_DIR

FINDXx

PCHEQ

32-Bit Interval Timer

16-Bit Index Counter

Hold Register

32-Bit Interval

Timer Register

Hold Register

COUNT_EN

PCHGE

EXTCNT

DIR_GATE

16-Bit Velocity

COUNT_ENCNT_DIR

Counter Register

PCLLE

PCHGE

DIVCLK

DIR

CNT_DIR

DIR_GATE

1’b0

PCLLE

CNTPOL

DIR_GATE

GATEN

DIVCLK

32-Bit Less Than

PCLLE

or Equal Comparator

PCLEQ

PCHGE

CCM

 INTDIV

(VELxCNT)

(INTxTMR)

(INTxHLD)

(INDXxCNT)

(INDXxHLD)

INDXxCNTL

INDXxCNTH POSxCNTLPOSxCNTH

(QEIxGEC)(1)

32-Bit Less Than or Equal

Compare Register

(QEIxLEC)

16-Bit Position Counter

Hold Register

(POSxHLD)

32-Bit Initialization and

Capture Register

(QEIxIC)(1)

QCAPEN

Note 1: These registers map to the same memory location.

OUTFNC

FLTREN

(POSxCNT)

32-Bit Position Counter Register

 QFDIV

32-Bit Greater Than

or Equal Comparator

 2009-2012 Microchip Technology Inc. DS70616G-page 323

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

17.1 QEI Resources

Many useful resources related to QEI are provided on

the main product page of the Microchip web site for the

devices listed in this data sheet. This product page,

which can be accessed using this link, contains the

latest updates and additional information.

17.1.1 KEY RESOURCES

•Section 15. “Quadrature Encoder Interface

(QEI)” (DS70601) in the “dsPIC33E/PIC24E

Family Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 324  2009-2012 Microchip Technology Inc.

17.2 QEI Control Registers

R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

QEIEN — QEISIDL PIMOD<2:0>(1)IMV<1:0>(2)

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— INTDIV<2:0>(3)CNTPOL GATEN CCM<1:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 QEIEN: Quadrature Encoder Interface Module Counter Enable bit

1 = Module counters are enabled

0 = Module counters are disabled, but SFRs can be read or written to

bit 14 Unimplemented: Read as ‘0’

bit 13 QEISIDL: QEI Stop in Idle Mode bit

1 = Discontinues module operation when device enters Idle mode

0 = Continues module operation in Idle mode

bit 12-10 PIMOD<2:0>: Position Counter Initialization Mode Select bits(1)

111 = Reserved

110 = Modulo Count mode for position counter

101 = Resets the position counter when the position counter equals the QEIxGEC register

100 = Second index event after home event initializes position counter with contents of the QEIxIC

011 = First index event after home event initializes position counter with contents of the QEIxIC

010 = Next index input event initializes the position counter with contents of the QEIxIC register

001 = Every index input event resets the position counter

000 = Index input event does not affect position counter

bit 9-8 IMV<1:0>: Index Match Value bits(2)

11 = Index match occurs when QEB = 1 and QEA = 1

10 = Index match occurs when QEB = 1 and QEA = 0

01 = Index match occurs when QEB = 0 and QEA = 1

00 = Index input event does not affect position counter

bit 7 Unimplemented: Read as ‘0’

Note 1: When CCM = 10 or CCM = 11, all of the QEI counters operate as timers and the PIMOD<2:0> bits are

ignored.

2: When CCM = 00, and QEA and QEB values match Index Match Value (IMV), the POSCNTH and

POSCNTL registers are reset.

3: The selected clock rate should be at least twice the expected maximum quadrature count rate.

 2009-2012 Microchip Technology Inc. DS70616G-page 325

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

bit 6-4 INTDIV<2:0>: Timer Input Clock Prescale Select bits (interval timer, main timer (position counter),

velocity counter and index counter internal clock divider select)(3)

111 = 1:128 prescale value

110 = 1:64 prescale value

101 = 1:32 prescale value

100 = 1:16 prescale value

011 = 1:8 prescale value

010 = 1:4 prescale value

001 = 1:2 prescale value

000 = 1:1 prescale value

bit 3 CNTPOL: Position and Index Counter/Timer Direction Select bit

1 = Counter direction is negative unless modified by external up/down signal

0 = Counter direction is positive unless modified by external up/down signal

bit 2 GATEN: External Count Gate Enable bit

1 = External gate signal controls position counter operation

0 = External gate signal does not affect position counter/timer operation

bit 1-0 CCM<1:0>: Counter Control Mode Selection bits

11 = Internal Timer mode with optional external count is selected

10 = External clock count with optional external count is selected

01 = External clock count with external up/down direction is selected

00 = Quadrature Encoder Interface (x4 mode) Count mode is selected

Note 1: When CCM = 10 or CCM = 11, all of the QEI counters operate as timers and the PIMOD<2:0> bits are

ignored.

2: When CCM = 00, and QEA and QEB values match Index Match Value (IMV), the POSCNTH and

POSCNTL registers are reset.

3: The selected clock rate should be at least twice the expected maximum quadrature count rate.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 326  2009-2012 Microchip Technology Inc.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

QCAPEN FLTREN QFDIV<2:0> OUTFNC<1:0> SWPAB

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R-x R-x R-x R-x

HOMPOL IDXPOL QEBPOL QEAPOL HOME INDEX QEB QEA

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 QCAPEN: Position Counter Input Capture Enable bit

1 = Positive edge detect of home input triggers position capture function

0 = HOMEx input event (positive edge) does not trigger a capture event

bit 14 FLTREN: QEAx/QEBx/INDXx/HOMEx Digital Filter Enable bit

1 = Input pin digital filter is enabled

0 = Input pin digital filter is disabled (bypassed)

bit 13-11 QFDIV<2:0>: QEAx/QEBx/INDXx/HOMEx Digital Input Filter Clock Divide Select bits

111 = 1:256 clock divide

110 = 1:64 clock divide

101 = 1:32 clock divide

100 = 1:16 clock divide

011 = 1:8 clock divide

010 = 1:4 clock divide

001 = 1:2 clock divide

000 = 1:1 clock divide

bit 10-9 OUTFNC<1:0>: QEI Module Output Function Mode Select bits

11 = The CTNCMPx pin goes high when QEIxLEC  POSxCNT  QEIxGEC

10 = The CTNCMPx pin goes high when POSxCNT  QEIxLEC

01 = The CTNCMPx pin goes high when POSxCNT  QEIxGEC

00 = Output is disabled

bit 8 SWPAB: Swap QEA and QEB Inputs bit

1 = QEAx and QEBx are swapped prior to quadrature decoder logic

0 = QEAx and QEBx are not swapped

bit 7 HOMPOL: HOMEx Input Polarity Select bit

1 = Input is inverted

0 = Input is not inverted

bit 6 IDXPOL: HOMEx Input Polarity Select bit

1 = Input is inverted

0 = Input is not inverted

bit 5 QEBPOL: QEBx Input Polarity Select bit

1 = Input is inverted

0 = Input is not inverted

bit 4 QEAPOL: QEAx Input Polarity Select bit

1 = Input is inverted

0 = Input is not inverted

bit 3 HOME: Status of HOMEx Input Pin After Polarity Control bit

1 = Pin is at logic ‘1’

0 = Pin is at logic ‘0’

 2009-2012 Microchip Technology Inc. DS70616G-page 327

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

bit 2 INDEX: Status of INDXx Input Pin After Polarity Control bit

1 = Pin is at logic ‘1’

0 = Pin is at logic ‘0’

bit 1 QEB: Status of QEBx Input Pin After Polarity Control And SWPAB Pin Swapping bit

1 = Pin is at logic ‘1’

0 = Pin is at logic ‘0’

bit 0 QEA: Status of QEAx Input Pin After Polarity Control And SWPAB Pin Swapping bit

1 = Pin is at logic ‘1’

0 = Pin is at logic ‘0’

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 328  2009-2012 Microchip Technology Inc.

U-0 U-0 HS, R/C-0 R/W-0 HS, R/C-0 R/W-0 HS, R/C-0 R/W-0

—— PCHEQIRQ PCHEQIEN PCLEQIRQ PCLEQIEN POSOVIRQ POSOVIEN

bit 15 bit 8

HS, R/C-0 R/W-0 HS, R/C-0 R/W-0 HS, R/C-0 R/W-0 HS, R/C-0 R/W-0

PCIIRQ(1)PCIIEN VELOVIRQ VELOVIEN HOMIRQ HOMIEN IDXIRQ IDXIEN

bit 7 bit 0

Legend: HS = Hardware Settable bit C = Clearable bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13 PCHEQIRQ: Position Counter Greater Than or Equal Compare Status bit

1 = POSxCNT ≥ QEIxGEC

0 = POSxCNT < QEIxGEC

bit 12 PCHEQIEN: Position Counter Greater Than or Equal Compare Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 11 PCLEQIRQ: Position Counter Less Than or Equal Compare Status bit

1 = POSxCNT ≤ QEIxLEC

0 = POSxCNT > QEIxLEC

bit 10 PCLEQIEN: Position Counter Less Than or Equal Compare Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 9 POSOVIRQ: Position Counter Overflow Status bit

1 = Overflow has occurred

0 = No overflow has occurred

bit 8 POSOVIEN: Position Counter Overflow Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 7 PCIIRQ: Position Counter (Homing) Initialization Process Complete Status bit(1)

1 = POSxCNT was reinitialized

0 = POSxCNT was not reinitialized

bit 6 PCIIEN: Position Counter (Homing) Initialization Process Complete interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 5 VELOVIRQ: Velocity Counter Overflow Status bit

1 = Overflow has occurred

0 = No overflow has not occurred

bit 4 VELOVIEN: Velocity Counter Overflow Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 3 HOMIRQ: Status Flag for Home Event Status bit

1 = Home event has occurred

0 = No Home event has occurred

Note 1: This status bit is only applicable to PIMOD<2:0> modes ‘011’ and ‘100’.

 2009-2012 Microchip Technology Inc. DS70616G-page 329

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

bit 2 HOMIEN: Home Input Event Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 1 IDXIRQ: Status Flag for Index Event Status bit

1 = Index event has occurred

0 = No Index event has occurred

bit 0 IDXIEN: Index Input Event Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

Note 1: This status bit is only applicable to PIMOD<2:0> modes ‘011’ and ‘100’.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 330  2009-2012 Microchip Technology Inc.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

POSCNT<31:24>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

POSCNT<23:16>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 POSCNT<31:16>: High Word Used to Form 32-Bit Position Counter Register (POSxCNT) bits

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

POSCNT<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

POSCNT<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 POSCNT<15:0>: Low Word Used to Form 32-Bit Position Counter Register (POSxCNT) bits

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

POSHLD<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

POSHLD<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 POSHLD<15:0>: Hold Register for Reading and Writing POSxCNTH bits

 2009-2012 Microchip Technology Inc. DS70616G-page 331

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

VELCNT<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

VELCNT<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 VELCNT<15:0>: Velocity Counter bits

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

INDXCNT<31:24>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

INDXCNT<23:16>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 INDXCNT<31:16>: High Word Used to Form 32-Bit Index Counter Register (INDXxCNT) bits

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

INDXCNT<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

INDXCNT<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 INDXCNT<15:0>: Low Word Used to Form 32-Bit Index Counter Register (INDXxCNT) bits

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 332  2009-2012 Microchip Technology Inc.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

INDXHLD<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

INDXHLD<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 INDXHLD<15:0>: Hold Register for Reading and Writing INDXxCNTH bits

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

QEIIC<31:24>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

QEIIC<23:16>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 QEIIC<31:16>: QEIx High Word Used to Form 32-Bit Initialization/Capture Register (QEIxIC) bits

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

QEIIC<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

QEIIC<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 QEIIC<15:0>: QEIx Low Word Used to Form 32-Bit Initialization/Capture Register (QEIxIC) bits

 2009-2012 Microchip Technology Inc. DS70616G-page 333

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

QEILEC<31:24>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

QEILEC<23:16>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 QEILEC<31:16>: QEIx High Word Used to Form 32-Bit Less Than or Equal Compare Register (QEIxLEC) bits

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

QEILEC<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

QEILEC<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 QEILEC<15:0>: QEIx Low Word Used to Form 32-Bit Less Than or Equal Compare Register (QEIxLEC) bits

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 334  2009-2012 Microchip Technology Inc.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

QEIGEC<31:24>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

QEIGEC<23:16>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 QEIGEC<31:16>: QEIx High Word Used to Form 32-Bit Greater Than or Equal Compare Register

(QEIxGEC) bits

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

QEIGEC<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

QEIGEC<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 QEIGEC<15:0>: QEIx Low Word Used to Form 32-Bit Greater Than or Equal Compare Register

(QEIxGEC) bits

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

INTTMR<31:24>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

INTTMR<23:16>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 INTTMR<31:16>: High Word Used to Form 32-Bit Interval Timer Register (INTxTMR) bits

 2009-2012 Microchip Technology Inc. DS70616G-page 335

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

INTTMR<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

INTTMR<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 INTTMR<15:0>: Low Word Used to Form 32-Bit Interval Timer Register (INTxTMR) bits

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

INTHLD<31:24>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

INTHLD<23:16>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 INTHLD<31:16>: Hold Register for Reading and Writing INTxTMRH bits

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

INTHLD<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

INTHLD<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 INTHLD<15:0>: Hold Register for Reading and Writing INTxTMRL bits

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 336  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 337

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

18.0 SERIAL PERIPHERAL

INTERFACE (SPI)

The SPI module is a synchronous serial interface use-

ful for communicating with other peripheral or micro-

controller devices. These peripheral devices can be

serial EEPROMs, shift registers, display drivers, ADC

Converters, etc. The SPI module is compatible with the

Motorola® SPI and SIOP interfaces.

Four SPI modules are provided on a single device.

These modules, which are designated as SPI1, SPI2,

SPI3 and SPI4, are functionally identical with the excep-

tion that SPI2 is not remappable. The dedicated SDI2,

SDO2 and SCK2 connections provide improved perfor-

mance over SPI1, SPI3 and SPI4 (see Section 32.0

“Electrical Characteristics”). Each SPI module

includes an eight-word FIFO buffer and allows DMA bus

connections. When using the SPI module with DMA,

FIFO operation can be disabled.

The SPIx serial interface consists of four pins, as

follows:

• SDIx: Serial Data Input

• SDOx: Serial Data Output

• SCKx: Shift Clock Input or Output

• SSx/FSYNCx: Active-Low Slave Select or Frame

Synchronization I/O Pulse

The SPIx module can be configured to operate with

two, three or four pins. In 3-pin mode, SSx is not used.

In 2-pin mode, neither SDOx nor SSx is used.

Figure 18-1 illustrates the block diagram of the SPI

module in Standard and Enhanced modes.

FIGURE 18-1: SPIx MODULE BLOCK DIAGRAM

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this

data sheet, refer to Section 18. “Serial

Peripheral Interface (SPI)” (DS70569)

of the “dsPIC33E/PIC24E Family

Reference Manual”, which is available

from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Note: In this section, the SPI modules are

referred to together as SPIx, or separately

as SPI1, SPI2, SPI3 and SPI4. Special

Function Registers follow a similar nota-

tion. For example, SPIxCON refers to the

control register for the SPI1, SPI2, SPI3

or SPI4 module.

Internal Data Bus

SDIx

SDOx

SSx/FSYNCx

SCKx

bit 0

Shift Control

Edge

Select

Enable

Sync

Control

Transfer

Write SPIxBUF

Read SPIxBUF

SPIxCON1<1:0>

SPIxCON1<4:2>

Master Clock

Note 1: In Standard mode, the FIFO is only one level deep.

Clock

Control

SPIxSR

8-Level FIFO

Transmit Buffer(1)

8-Level FIFO

Receive Buffer(1)

SPIxBUF

Primary

1:1/4/16/64

Prescaler

Secondary

Prescaler

1:1 to 1:8

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 338  2009-2012 Microchip Technology Inc.

18.1 SPI Helpful Tips

1. In Frame mode, if there is a possibility that the

master may not be initialized before the slave:

a) If FRMPOL (SPIxCON2<13>) = 1, use a

pull-down resistor on SSx.

b) If FRMPOL = 0, use a pull-up resistor on

SSx.

2. In Non-Framed 3-Wire mode, (i.e., not using

SSx from a master):

a) If CKP (SPIxCON1<6>) = 1, always place a

pull-up resistor on SSx.

b) If CKP = 0, always place a pull-down

resistor on SSx.

3. FRMEN (SPIxCON2<15>) = 1 and SSEN

(SPIxCON1<7>) = 1 are exclusive and invalid.

In Frame mode, SCKx is continuous and the

Frame Sync pulse is active on the SSx pin,

which indicates the start of a data frame.

4. In Master mode only, set the SMP bit

(SPIxCON1<9>) to a ‘1’ for the fastest SPI data

rate possible. The SMP bit can only be set at the

same time or after the MSTEN bit

(SPIxCON1<5>) is set.

To avoid invalid slave read data to the master, the

user’s master software must ensure enough time for

slave software to fill its write buffer before the user

application initiates a master write/read cycle. It is

always advisable to preload the SPIxBUF Transmit

cycle. SPIxBUF is transferred to the SPIx Shift register

and is empty once the data transmission begins.

18.2 SPI Resources

Many useful resources related to SPI are provided on

the main product page of the Microchip web site for the

devices listed in this data sheet. This product page,

which can be accessed using this link, contains the

latest updates and additional information.

18.2.1 KEY RESOURCES

•Section 18. “Serial Peripheral Interface (SPI)”

(DS70569) in the “dsPIC33E/PIC24E Family

Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

Note: This insures that the first frame

transmission after initialization is not

shifted or corrupted.

Note: This will insure that during power-up and

initialization, the master/slave will not lose

synchronization due to an errant SCKx

transition that would cause the slave to

accumulate data shift errors, for both

transmit and receive, appearing as

corrupted data.

Note: Not all third-party devices support Frame

mode timing. Refer to the SPIx electrical

characteristics for details.

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554301

 2009-2012 Microchip Technology Inc. DS70616G-page 339

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

18.3 SPI Control Registers

R/W-0 U-0 R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0

SPIEN —SPISIDL —— SPIBEC<2:0>

bit 15 bit 8

R/W-0 R/C-0, HS R/W-0 R/W-0 R/W-0 R/W-0 R-0, HS, HC R-0, HS, HC

SRMPT SPIROV SRXMPT SISEL<2:0> SPITBF SPIRBF

bit 7 bit 0

Legend: C = Clearable bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

HS = Hardware Settable bit HC = Hardware Clearable bit U = Unimplemented bit, read as ‘0’

bit 15 SPIEN: SPIx Enable bit

1 = Enables the module and configures SCKx, SDOx, SDIx and SSx as serial port pins

0 = Disables the module

bit 14 Unimplemented: Read as ‘0’

bit 13 SPISIDL: SPIx Stop in Idle Mode bit

1 = Discontinues the module operation when device enters Idle mode

0 = Continues the module operation in Idle mode

bit 12-11 Unimplemented: Read as ‘0’

bit 10-8 SPIBEC<2:0>: SPIx Buffer Element Count bits (valid in Enhanced Buffer mode)

Master mode:

Number of SPIx transfers that are pending.

Slave mode:

Number of SPIx transfers that are unread.

bit 7 SRMPT: SPIx Shift Register (SPIxSR) Empty bit (valid in Enhanced Buffer mode)

1 = SPIx Shift register is empty and Ready-to-Send or receive the data

0 = SPIx Shift register is not empty

bit 6 SPIROV: SPIx Receive Overflow Flag bit

1 = A new byte/word is completely received and discarded; the user application has not read the

previous data in the SPIxBUF register

0 = No overflow has occurred

bit 5 SRXMPT: SPIx Receive FIFO Empty bit (valid in Enhanced Buffer mode)

1 = RX FIFO is empty

0 = RX FIFO is not empty

bit 4-2 SISEL<2:0>: SPIx Buffer Interrupt Mode bits (valid in Enhanced Buffer mode)

111 = Interrupt when the SPIx transmit buffer is full

110 = Interrupt when last bit is shifted into SPIxSR, and as a result, the TX FIFO is empty

101 = Interrupt when the last bit is shifted out of SPIxSR and the transmit is complete

100 = Interrupt when one data is shifted into the SPIxSR, and as a result, the TX FIFO has one open

memory location

011 = Interrupt when the SPIx receive buffer is full

010 = Interrupt when the SPIx receive buffer is 3/4 or more full

001 = Interrupt when data is available in the receive buffer (SRMPT bit is set)

000 = Interrupt when the last data in the receive buffer is read, and as a result, the buffer is empty

(SRXMPT bit is set)

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 340  2009-2012 Microchip Technology Inc.

bit 1 SPITBF: SPIx Transmit Buffer Full Status bit

1 = Transmit has not yet started, SPIx transmit buffer is full

0 = Transmit has started, SPIx transmit buffer is empty

Standard Buffer Mode:

Automatically set in hardware when the core writes to the SPIxBUF location, loading the SPIx transmit

buffer. Automatically cleared in hardware when the SPIx module transfers data from the SPIx transmit

buffer to SPIxSR.

Enhanced Buffer Mode:

Automatically set in hardware when CPU writes to the SPIxBUF location, loading the last available

buffer location. Automatically cleared in hardware when a buffer location is available for a CPU write

operation.

bit 0 SPIRBF: SPIx Receive Buffer Full Status bit

1 = Receive complete, SPIx receive buffer is full

0 = Receive is incomplete, SPIx receive buffer is empty

Standard Buffer Mode:

Automatically set in hardware when SPIx transfers data from SPIxSR to the SPIx receive buffer.

Automatically cleared in hardware when the core reads the SPIxBUF location, reading the SPIx

receive buffer.

Enhanced Buffer Mode:

Automatically set in hardware when SPIx transfers data from SPIxSR to the buffer, filling the last

unread buffer location. Automatically cleared in hardware when a buffer location is available for a

transfer from SPIxSR.

 2009-2012 Microchip Technology Inc. DS70616G-page 341

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— — — DISSCK DISSDO MODE16 SMP(4)CKE(1)

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SSEN(2)CKP MSTEN SPRE<2:0>(3)PPRE<1:0>(3)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-13 Unimplemented: Read as ‘0’

bit 12 DISSCK: Disable SCKx Pin bit (SPIx Master modes only)

1 = Internal SPIx clock is disabled, pin functions as I/O

0 = Internal SPIx clock is enabled

bit 11 DISSDO: Disable SDOx Pin bit

1 = SDOx pin is not used by the module; pin functions as I/O

0 = SDOx pin is controlled by the module

bit 10 MODE16: Word/Byte Communication Select bit

1 = Communication is word-wide (16 bits)

0 = Communication is byte-wide (8 bits)

bit 9 SMP: SPIx Data Input Sample Phase bit(4)

Master mode:

1 = Input data is sampled at end of data output time

0 = Input data is sampled at middle of data output time

Slave mode:

The SMP bit must be cleared when SPIx module is used in Slave mode.

bit 8 CKE: SPIx Clock Edge Select bit(1)

1 = Serial output data changes on transition from active clock state to Idle clock state (refer to bit 6)

0 = Serial output data changes on transition from Idle clock state to active clock state (refer to bit 6)

bit 7 SSEN: Slave Select Enable bit (Slave mode)(2)

1 = SSx pin is used for Slave mode

0 = SSx pin is not used by module, pin is controlled by port function

bit 6 CKP: Clock Polarity Select bit

1 = Idle state for clock is a high level; active state is a low level

0 = Idle state for clock is a low level; active state is a high level

bit 5 MSTEN: Master Mode Enable bit

1 = Master mode

0 = Slave mode

Note 1: The CKE bit is not used in the Framed SPIx modes. Program this bit to ‘0’ for Framed SPIx modes

(FRMEN = 1).

2: This bit must be cleared when FRMEN = 1.

3: Do not set both primary and secondary prescalers to a value of 1:1.

4: The SMP bit must be set only after setting the MSTEN bit. The SMP bit remains cleared if MSTEN = 0.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 342  2009-2012 Microchip Technology Inc.

bit 4-2 SPRE<2:0>: Secondary Prescale bits (Master mode)(3)

111 = Secondary prescale 1:1

110 = Secondary prescale 2:1

•

000 = Secondary prescale 8:1

bit 1-0 PPRE<1:0>: Primary Prescale bits (Master mode)(3)

11 = Primary prescale 1:1

10 = Primary prescale 4:1

01 = Primary prescale 16:1

00 = Primary prescale 64:1

Note 1: The CKE bit is not used in the Framed SPIx modes. Program this bit to ‘0’ for Framed SPIx modes

(FRMEN = 1).

2: This bit must be cleared when FRMEN = 1.

3: Do not set both primary and secondary prescalers to a value of 1:1.

4: The SMP bit must be set only after setting the MSTEN bit. The SMP bit remains cleared if MSTEN = 0.

 2009-2012 Microchip Technology Inc. DS70616G-page 343

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0

FRMEN SPIFSD FRMPOL — — — — —

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0

— — — — — — FRMDLY SPIBEN

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 FRMEN: Framed SPIx Support bit

1 = Framed SPIx support is enabled (SSx pin is used as a Frame Sync pulse input/output)

0 = Framed SPIx support is disabled

bit 14 SPIFSD: Frame Sync Pulse Direction Control bit

1 = Frame Sync pulse input (slave)

0 = Frame Sync pulse output (master)

bit 13 FRMPOL: Frame Sync Pulse Polarity bit

1 = Frame Sync pulse is active-high

0 = Frame Sync pulse is active-low

bit 12-2 Unimplemented: Read as ‘0’

bit 1 FRMDLY: Frame Sync Pulse Edge Select bit

1 = Frame Sync pulse coincides with the first bit clock

0 = Frame Sync pulse precedes the first bit clock

bit 0 SPIBEN: Enhanced Buffer Enable bit

1 = Enhanced Buffer is enabled

0 = Enhanced Buffer is disabled (Standard mode)

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 344  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 345

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

19.0 INTER-INTEGRATED

CIRCUIT™ (I2C™)

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 family of devices con-

tain two Inter-Integrated Circuit (I2C) modules: I2C1

and I2C2.

The I2C module provides complete hardware support

for both Slave and Multi-Master modes of the I2C serial

communication standard, with a 16-bit interface.

The I2C module has a 2-pin interface:

• The SCLx pin is the clock.

• The SDAx pin is the data.

The I2C module offers the following key features:

•I

2C interface supporting both Master and Slave

modes of operation.

•I

2C Slave mode supports 7 and 10-bit addressing.

•I

2C Master mode supports 7 and 10-bit addressing.

•I

2C port allows bidirectional transfers between

master and slaves.

• Serial clock synchronization for I2C port can be

used as a handshake mechanism to suspend and

resume serial transfer (SCLREL control).

•I

2C supports multi-master operation, detects bus

collision and arbitrates accordingly.

• IPMI support

• SMBus support

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this

data sheet, refer to Section 19. “Inter-

Integrated Circuit™ (I2C™)”

(DS70330) of the “dsPIC33E/PIC24E

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 346  2009-2012 Microchip Technology Inc.

FIGURE 19-1: I2C™ BLOCK DIAGRAM (X = 1 OR 2)

Internal

Data Bus

SCLx/

SDAx/

Shift

Match Detect

I2CxADD

Start and Stop

Bit Detect

Clock

Address Match

Clock

Stretching

I2CxTRN

LSb

Shift Clock

BRG Down Counter

Start and Stop

Bit Generation

Acknowledge

Generation

Collision

Detect

I2CxCON

I2CxSTAT

Control Logic

Read

LSb

Write

Read

I2CxBRG

I2CxRSR

Write

Read

Write

Read

Write

Read

Write

Read

Write

Read

I2CxRCV

ASDAx(1)

ASDLx(1)

Note 1: The availability of I2C interfaces varies by device. Refer to the “Pin Diagrams” section for availability.

Selection (SDAx/SCLx or ASDAx/ASCLx) is made using the device Configuration bits, ALTI2C1 and

ALTI2C2 (FPOR<5:4>). See Section 29.0 “Special Features” for more information.

Reload

Control

I2CxMSK

 2009-2012 Microchip Technology Inc. DS70616G-page 347

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

19.1 I2C Resources

Many useful resources related to I2C are provided on

the main product page of the Microchip web site for the

devices listed in this data sheet. This product page,

which can be accessed using this link, contains the

latest updates and additional information.

19.1.1 KEY RESOURCES

•Section 19. “Inter-Integrated Circuit™ (I2C™)”

(DS70330) in the “dsPIC33E/PIC24E Family

Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 348  2009-2012 Microchip Technology Inc.

19.2 I2C Control Registers

R/W-0 U-0 R/W-0 R/W-1, HC R/W-0 R/W-0 R/W-0 R/W-0

I2CEN — I2CSIDL SCLREL IPMIEN(1)A10M DISSLW SMEN

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0, HC R/W-0, HC R/W-0, HC R/W-0, HC R/W-0, HC

GCEN STREN ACKDT ACKEN RCEN PEN RSEN SEN

bit 7 bit 0

Legend: HC = Hardware Clearable bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 I2CEN: I2Cx Enable bit

1 = Enables the I2Cx module and configures the SDAx and SCLx pins as serial port pins

0 = Disables the I2Cx module; all I2C™ pins are controlled by port functions

bit 14 Unimplemented: Read as ‘0’

bit 13 I2CSIDL: I2Cx Stop in Idle Mode bit

1 = Discontinues module operation when device enters an Idle mode

0 = Continues module operation in Idle mode

bit 12 SCLREL: SCLx Release Control bit (when operating as I2C slave)

1 = Releases SCLx clock

0 = Holds SCLx clock low (clock stretch)

If STREN = 1:

The bit is R/W (i.e., software can write ‘0’ to initiate stretch and write ‘1’ to release clock). Hardware is clear

at beginning of every slave data byte transmission. Hardware is clear at the end of every slave address

byte reception. Hardware is clear at end of every slave data byte reception.

If STREN = 0:

The bit is R/S (i.e., software can only write ‘1’ to release clock). Hardware is clear at beginning of every

slave data byte transmission. Hardware is clear at the end of every slave address byte reception.

bit 11 IPMIEN: Intelligent Peripheral Management Interface (IPMI) Enable bit(1)

1 = IPMI mode is enabled; all addresses Acknowledged

0 = IPMI mode is disabled

bit 10 A10M: 10-Bit Slave Address bit

1 = I2CxADD is a 10-bit slave address

0 = I2CxADD is a 7-bit slave address

bit 9 DISSLW: Disable Slew Rate Control bit

1 = Slew rate control is disabled

0 = Slew rate control is enabled

bit 8 SMEN: SMBus Input Levels bit

1 = Enables I/O pin thresholds compliant with the SMBus specification

0 = Disables SMBus input thresholds

bit 7 GCEN: General Call Enable bit (when operating as I2C slave)

1 = Enables interrupt when a general call address is received in the I2CxRSR (module is enabled for reception)

0 = General call address is disabled

Note 1: When performing master operations, ensure that the IPMIEN bit is ‘0’.

 2009-2012 Microchip Technology Inc. DS70616G-page 349

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

bit 6 STREN: SCLx Clock Stretch Enable bit (when operating as I2C slave)

Used in conjunction with the SCLREL bit.

1 = Enables software or receives clock stretching

0 = Disables software or receives clock stretching

bit 5 ACKDT: Acknowledge Data bit (when operating as I2C master, applicable during master receive)

Value that is transmitted when the software initiates an Acknowledge sequence.

1 = Sends NACK during Acknowledge

0 = Sends ACK during Acknowledge

bit 4

ACKEN:

Acknowledge Sequence Enable bit (when operating as I

C master, applicable during master receive)

1 = Initiates Acknowledge sequence on SDAx and SCLx pins and transmits the ACKDT data bit. Hardware

is clear at the end of a master Acknowledge sequence.

0 = Acknowledge sequence is not in progress

bit 3 RCEN: Receive Enable bit (when operating as I2C master)

1 = Enables Receive mode for I2C. Hardware is clear at the end of the eighth bit of a master receive data byte.

0 = Receive sequence is not in progress

bit 2 PEN: Stop Condition Enable bit (when operating as I2C master)

1 = Initiates Stop condition on SDAx and SCLx pins. Hardware is clear at the end of a master Stop sequence.

0 = Stop condition is not in progress

bit 1 RSEN: Repeated Start Condition Enable bit (when operating as I2C master)

1 = Initiates Repeated Start condition on SDAx and SCLx pins. Hardware is clear at the end of a master

Repeated Start sequence.

0 = Repeated Start condition is not in progress

bit 0 SEN: Start Condition Enable bit (when operating as I2C master)

1 = Initiates Start condition on SDAx and SCLx pins. Hardware is clear at the end of a master Start sequence.

0 = Start condition is not in progress

Note 1: When performing master operations, ensure that the IPMIEN bit is ‘0’.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 350  2009-2012 Microchip Technology Inc.

R-0, HSC R-0, HSC U-0 U-0 U-0 R/C-0, HS R-0, HSC R-0, HSC

ACKSTAT TRSTAT — — — BCL GCSTAT ADD10

bit 15 bit 8

R/C-0, HS R/C-0, HS R-0, HSC R/C-0, HSC R/C-0, HSC R-0, HSC R-0, HSC R-0, HSC

IWCOL I2COV D_A P S R_W RBF TBF

bit 7 bit 0

Legend: C = Clearable bit U = Unimplemented bit, read as ‘0’

R = Readable bit W = Writable bit HS = Hardware Settable bit HSC = Hardware Settable/Clearable bit

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 ACKSTAT: Acknowledge Status bit

(when operating as I2C™ master, applicable to master transmit operation)

1 = NACK received from slave

0 = ACK received from slave

Hardware is set or clear at the end of a slave Acknowledge.

bit 14 TRSTAT: Transmit Status bit (when operating as I2C master, applicable to master transmit operation)

1 = Master transmit is in progress (8 bits + ACK)

0 = Master transmit is not in progress

Hardware is set at the beginning of a master transmission. Hardware is clear at the end of a slave

Acknowledge.

bit 13-11 Unimplemented: Read as ‘0’

bit 10 BCL: Master Bus Collision Detect bit

1 = A bus collision has been detected during a master operation

0 = No collision

Hardware is set at detection of a bus collision.

bit 9 GCSTAT: General Call Status bit

1 = General call address was received

0 = General call address was not received

Hardware is set when an address matches the general call address. Hardware is clear at a Stop detection.

bit 8 ADD10: 10-Bit Address Status bit

1 = 10-bit address was matched

0 = 10-bit address was not matched

Hardware is set at a match of the 2nd byte of a matched 10-bit address. Hardware is clear at a Stop detection.

bit 7 IWCOL: Write Collision Detect bit

1 = An attempt to write to the I2CxTRN register failed because the I2C module is busy

0 = No collision

Hardware is set at an occurrence of a write to I2CxTRN while busy (cleared by software).

bit 6 I2COV: I2Cx Receive Overflow Flag bit

1 = A byte was received while the I2CxRCV register is still holding the previous byte

0 = No overflow

Hardware is set at an attempt to transfer I2CxRSR to I2CxRCV (cleared by software).

bit 5 D_A: Data/Address bit (when operating as I2C slave)

1 = Indicates that the last byte received was data

0 = Indicates that the last byte received was a device address

Hardware is clear at a device address match. Hardware is set by reception of a slave byte.

bit 4 P: Stop bit

1 = Indicates that a Stop bit has been detected last

0 = Stop bit was not detected last

Hardware is set or clear when a Start, Repeated Start or Stop is detected.

 2009-2012 Microchip Technology Inc. DS70616G-page 351

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

bit 3 S: Start bit

1 = Indicates that a Start (or Repeated Start) bit has been detected last

0 = Start bit was not detected last

Hardware is set or clear when a Start, Repeated Start or Stop is detected.

bit 2 R_W: Read/Write Information bit (when operating as I2C slave)

1 = Read – indicates data transfer is output from a slave

0 = Write – indicates data transfer is input to a slave

Hardware is set or clear after reception of an I2C device address byte.

bit 1 RBF: Receive Buffer Full Status bit

1 = Receive is complete, I2CxRCV is full

0 = Receive is not complete, I2CxRCV is empty

Hardware is set when I2CxRCV is written with a received byte. Hardware is clear when software reads

I2CxRCV.

bit 0 TBF: Transmit Buffer Full Status bit

1 = Transmit is in progress, I2CxTRN is full

0 = Transmit is complete, I2CxTRN is empty

Hardware is set when software writes to I2CxTRN. Hardware is clear at completion of a data transmission.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 352  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0

— — — — — — AMSK9 AMSK8

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

AMSK7 AMSK6 AMSK5 AMSK4 AMSK3 AMSK2 AMSK1 AMSK0

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-10 Unimplemented: Read as ‘0’

bit 9-0 AMSKx: Mask for Address bit x Select bit

For 10-Bit Address:

1 = Enables masking for bit Ax of incoming message address; bit match is not required in this position

0 = Disables masking for bit Ax; bit match is required in this position

For 7-Bit Address (I2CxMSK<6:0> only):

1 = Enables masking for bit Ax + 1 of incoming message address; bit match is not required in this position

0 = Disable masking for bit Ax + 1; bit match is required in this position

 2009-2012 Microchip Technology Inc. DS70616G-page 353

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

20.0 UNIVERSAL ASYNCHRONOUS

RECEIVER TRANSMITTER

(UART)

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 family of devices

contains four UART modules.

The Universal Asynchronous Receiver Transmitter

(UART) module is one of the serial I/O modules

available in the dsPIC33EPXXX(GP/MC/MU)806/810/

814 and PIC24EPXXX(GP/GU)810/814 device family.

The UART is a full-duplex, asynchronous system that

can communicate with peripheral devices, such as

personal computers, LIN/J2602, RS-232 and RS-485

interfaces. The module also supports a hardware flow

control option with the UxCTS and UxRTS pins, and

also includes an IrDA® encoder and decoder.

The primary features of the UARTx module are:

• Full-Duplex, 8 or 9-Bit Data Transmission through

the UxTX and UxRX Pins

• Even, Odd or No Parity Options (for 8-bit data)

• One or Two Stop bits

• Hardware Flow Control Option with UxCTS and

UxRTS Pins

• Fully Integrated Baud Rate Generator with 16-Bit

Prescaler

• Baud Rates Ranging from 4.375 Mbps to 67 bps at

16x mode at 70 MIPS

• Baud Rates Ranging from 17.5 Mbps to 267 bps at

4x mode at 70 MIPS

• 4-Deep First-In First-Out (FIFO) Transmit Data

Buffer

• 4-Deep FIFO Receive Data Buffer

• Parity, Framing and Buffer Overrun Error Detection

• Support for 9-bit mode with Address Detect

(9th bit = 1)

• Transmit and Receive Interrupts

• A Separate Interrupt for All UARTx Error Conditions

• Loopback mode for Diagnostic Support

• Support for Sync and Break Characters

• Support for Automatic Baud Rate Detection

•IrDA

® Encoder and Decoder Logic

• 16x Baud Clock Output for IrDA Support

A simplified block diagram of the UARTx module is

shown in Figure 20-1. The UARTx module consists of

these key hardware elements:

• Baud Rate Generator

• Asynchronous Transmitter

• Asynchronous Receiver

FIGURE 20-1: UARTx SIMPLIFIED BLOCK DIAGRAM

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this

data sheet, refer to Section 17. “UART”

(DS70582) of the “dsPIC33E/PIC24E

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

UxRX

Hardware Flow Control

UARTx Receiver

UARTx Transmitter UxTX

Baud Rate Generator

UxRTS

UxCTS

IrDA®

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 354  2009-2012 Microchip Technology Inc.

20.1 UARTx Helpful Tips

1. In multi-node direct-connect UARTx networks,

UARTx receive inputs react to the complemen-

tary logic level defined by the URXINV bit

(UxMODE<4>), which defines the Idle state, the

default of which is logic high (i.e., URXINV = 0).

Because remote devices do not initialize at the

same time, it is likely that one of the devices,

because the RX line is floating, will trigger a

Start bit detection and will cause the first byte

received, after the device has been initialized, to

be invalid. To avoid this situation, the user

should use a pull-up or pull-down resistor on the

RX pin depending on the value of the URXINV

bit.

a) If URXINV = 0, use a pull-up resistor on the

RX pin.

b) If URXINV = 1, use a pull-down resistor on

the RX pin.

2. The first character received on a wake-up from

Sleep mode, caused by activity on the UxRX pin

of the UARTx module, will be invalid. In Sleep

mode, peripheral clocks are disabled. By the

time the oscillator system has restarted and

stabilized from Sleep mode, the baud rate bit

sampling clock, relative to the incoming UxRX

bit timing, is no longer synchronized resulting in

the first character being invalid. This is to be

expected.

20.2 UARTx Resources

Many useful resources related to the UARTx are

provided on the main product page of the Microchip

web site for the devices listed in this data sheet. This

product page, which can be accessed using this link,

contains the latest updates and additional information.

20.2.1 KEY RESOURCES

•Section 17. “UART” (DS70582) in the

“dsPIC33E/PIC24E Family Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

 2009-2012 Microchip Technology Inc. DS70616G-page 355

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

20.3 UARTx Registers

R/W-0 U-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0

UARTEN(1)— USIDL IREN(2)RTSMD —UEN<1:0>

bit 15 bit 8

R/W-0, HC R/W-0 R/W-0, HC R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

WAKE LPBACK ABAUD URXINV BRGH PDSEL<1:0> STSEL

bit 7 bit 0

Legend: HC = Hardware Clearable bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 UARTEN: UARTx Enable bit(1)

1 = UARTx is enabled; all UARTx pins are controlled by UARTx as defined by UEN<1:0>

0 = UARTx is disabled; all UARTx pins are controlled by port latches; UARTx power consumption is

minimal

bit 14 Unimplemented: Read as ‘0’

bit 13 USIDL: UARTx Stop in Idle Mode bit

1 = Discontinues module operation when device enters Idle mode

0 = Continues module operation in Idle mode

bit 12 IREN: IrDA® Encoder and Decoder Enable bit(2)

1 = IrDA encoder and decoder are enabled

0 = IrDA encoder and decoder are disabled

bit 11 RTSMD: Mode Selection for UxRTS Pin bit

1 =UxRTS pin in Simplex mode

0 =UxRTS

pin in Flow Control mode

bit 10 Unimplemented: Read as ‘0’

bit 9-8 UEN<1:0>: UARTx Pin Enable bits

11 = UxTX, UxRX and BCLK pins are enabled and used; UxCTS pin is controlled by port latches

10 = UxTX, UxRX, UxCTS and UxRTS pins are enabled and used

01 = UxTX, UxRX and UxRTS pins are enabled and used; UxCTS pin is controlled by port latches

00 = UxTX and UxRX pins are enabled and used; UxCTS and UxRTS/BCLK pins are controlled by

port latches

bit 7 WAKE: Wake-up on Start Bit Detect During Sleep Mode Enable bit

1 = UARTx continues to sample the UxRX pin; interrupt is generated on falling edge; bit is cleared in

hardware on following rising edge

0 = No wake-up is enabled

bit 6 LPBACK: UARTx Loopback Mode Select bit

1 = Enables Loopback mode

0 = Loopback mode is disabled

bit 5 ABAUD: Auto-Baud Enable bit

1 = Enables baud rate measurement on the next character – requires reception of a Sync field (55h)

before other data; cleared in hardware upon completion

0 = Baud rate measurement is disabled or has completed

Note 1: Refer to Section 17. “UART” (DS70582) in the “dsPIC33E/PIC24E Family Reference Manual” for

information on enabling the UARTx module for receive or transmit operation.

2: This feature is only available for the 16x BRG mode (BRGH = 0).

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 356  2009-2012 Microchip Technology Inc.

bit 4 URXINV: Receive Polarity Inversion bit

1 = UxRX Idle state is ‘0’

0 = UxRX Idle state is ‘1’

bit 3 BRGH: High Baud Rate Enable bit

1 = BRG generates 4 clocks per bit period (4x baud clock, High-Speed mode)

0 = BRG generates 16 clocks per bit period (16x baud clock, Standard mode)

bit 2-1 PDSEL<1:0>: Parity and Data Selection bits

11 = 9-bit data, no parity

10 = 8-bit data, odd parity

01 = 8-bit data, even parity

00 = 8-bit data, no parity

bit 0 STSEL: Stop Bit Selection bit

1 = Two Stop bits

0 = One Stop bit

Note 1: Refer to Section 17. “UART” (DS70582) in the “dsPIC33E/PIC24E Family Reference Manual” for

information on enabling the UARTx module for receive or transmit operation.

2: This feature is only available for the 16x BRG mode (BRGH = 0).

 2009-2012 Microchip Technology Inc. DS70616G-page 357

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 U-0 R/W-0, HC R/W-0 R-0 R-1

UTXISEL1 UTXINV UTXISEL0 — UTXBRK UTXEN(1)UTXBF TRMT

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R-1 R-0 R-0 R/C-0 R-0

URXISEL<1:0> ADDEN RIDLE PERR FERR OERR URXDA

bit 7 bit 0

Legend: HC = Hardware Clearable bit C = Clearable bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15,13 UTXISEL<1:0>: UARTx Transmission Interrupt Mode Selection bits

11 = Reserved; do not use

10 = Interrupt when a character is transferred to the Transmit Shift Register (TSR) and as a result, the

transmit buffer becomes empty

01 = Interrupt when the last character is shifted out of the Transmit Shift Register; all transmit

operations are completed

00 = Interrupt when a character is transferred to the Transmit Shift Register (this implies there is at

least one character open in the transmit buffer)

bit 14 UTXINV: UARTx Transmit Polarity Inversion bit

If IREN = 0:

1 = UxTX Idle state is ‘0’

0 = UxTX Idle state is ‘1’

If IREN = 1:

1 = IrDA encoded, UxTX Idle state is ‘1’

0 = IrDA encoded, UxTX Idle state is ‘0’

bit 12 Unimplemented: Read as ‘0’

bit 11 UTXBRK: UARTx Transmit Break bit

1 = Sends Sync Break on next transmission – Start bit, followed by twelve ‘0’ bits, followed by Stop bit;

cleared by hardware upon completion

0 = Sync Break transmission is disabled or completed

bit 10 UTXEN: UARTx Transmit Enable bit(1)

1 = Transmit is enabled, UxTX pin is controlled by UARTx

0 = Transmit is disabled, any pending transmission is aborted and the buffer is reset; UxTX pin

controlled by port

bit 9 UTXBF: UARTx Transmit Buffer Full Status bit (read-only)

1 = Transmit buffer is full

0 = Transmit buffer is not full, at least one more character can be written

bit 8 TRMT: Transmit Shift Register Empty bit (read-only)

1 = Transmit Shift Register is empty and transmit buffer is empty (the last transmission has completed)

0 = Transmit Shift Register is not empty, a transmission is in progress or queued

bit 7-6 URXISEL<1:0>: UARTx Receive Interrupt Mode Selection bits

11 = Interrupt is set on UxRSR transfer making the receive buffer full (i.e., has 4 data characters)

10 = Interrupt is set on UxRSR transfer making the receive buffer 3/4 full (i.e., has 3 data characters)

0x = Interrupt is set when any character is received and transferred from the UxRSR to the receive

buffer; receive buffer has one or more characters

Note 1: Refer to Section 17. “UART” (DS70582) in the “dsPIC33E/PIC24E Family Reference Manual” for

information on enabling the UARTx module for transmit operation.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 358  2009-2012 Microchip Technology Inc.

bit 5 ADDEN: Address Character Detect bit (bit 8 of received data = 1)

1 = Address Detect mode is enabled; if 9-bit mode is not selected, this does not take effect

0 = Address Detect mode is disabled

bit 4 RIDLE: Receiver Idle bit (read-only)

1 =Receiver is Idle

0 = Receiver is active

bit 3 PERR: Parity Error Status bit (read-only)

1 = Parity error has been detected for the current character (character at the top of the receive FIFO)

0 = Parity error has not been detected

bit 2 FERR: Framing Error Status bit (read-only)

1 = Framing error has been detected for the current character (character at the top of the receive

FIFO)

0 = Framing error has not been detected

bit 1 OERR: Receive Buffer Overrun Error Status bit (read/clear only)

1 = Receive buffer has overflowed

0 = Receive buffer has not overflowed; clearing a previously set OERR bit (10 transition) resets

the receiver buffer and the UxRSR to the empty state

bit 0 URXDA: Receive Buffer Data Available bit (read-only)

1 = Receive buffer has data, at least one more character can be read

0 = Receive buffer is empty

Note 1: Refer to Section 17. “UART” (DS70582) in the “dsPIC33E/PIC24E Family Reference Manual” for

information on enabling the UARTx module for transmit operation.

 2009-2012 Microchip Technology Inc. DS70616G-page 359

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

21.0 ENHANCED CAN (ECAN™)

MODULE

21.1 Overview

The Enhanced Controller Area Network (ECAN)

module is a serial interface, useful for communicat-

ing with other CAN modules or microcontroller

devices. This interface/protocol was designed to

allow communications within noisy environments.

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices contain two

ECAN modules.

The ECANx module is a communication controller

implementing the CAN 2.0 A/B protocol, as defined in

the BOSCH CAN Specification. The module supports

CAN 1.2, CAN 2.0A, CAN 2.0B Passive and CAN 2.0B

Active versions of the protocol. The module implemen-

tation is a full CAN system. The CAN Specification is

not covered within this data sheet. The reader can refer

to the BOSCH CAN specification for further details.

The ECANx module features are as follows:

• Implementation of the CAN Protocol, CAN 1.2,

CAN 2.0A and CAN 2.0B

• Standard and Extended Data Frames

• 0-8 Bytes Data Length

• Programmable Bit Rate up to 1 Mbit/sec

• Automatic Response to Remote Transmission

Requests

• Up to 8 Transmit Buffers with Application-Specific

Prioritization and Abort Capability (each buffer

can contain up to 8 bytes of data)

• Up to 32 Receive Buffers (each buffer can contain

up to 8 bytes of data)

• Up to 16 Full (standard/extended identifier)

Acceptance Filters

• Three Full Acceptance Filter Masks

• DeviceNet™ Addressing Support

• Programmable Wake-up Functionality with

Integrated Low-Pass Filter

• Programmable Loopback mode Supports

Self-Test Operation

• Signaling via Interrupt Capabilities for all CAN

Receiver and Transmitter Error States

• Programmable Clock Source

• Programmable Link to Input Capture Module (IC2

for the ECAN1 and ECAN2 modules) for

Time-Stamping and Network Synchronization

• Low-Power Sleep and Idle mode

The CAN bus module consists of a protocol engine and

message buffering/control. The CAN protocol engine

handles all functions for receiving and transmitting

messages on the CAN bus. Messages are transmitted

by first loading the appropriate data registers. Status

and errors can be checked by reading the appropriate

registers. Any message detected on the CAN bus is

checked for errors and then matched against filters to

see if it should be received and stored in one of the

receive registers.

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this

data sheet, refer to Section 21.

“Enhanced Controller Area Network

(ECAN™)” (DS70353) of the “dsPIC33E/

PIC24E Family Reference Manual”,

which is available from the Microchip web

site (www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 360  2009-2012 Microchip Technology Inc.

FIGURE 21-1: ECANx MODULE BLOCK DIAGRAM

CAN Protocol

Engine

CxTX CxRX

RxF14 Filter

RxF13 Filter

RxF12 Filter

RxF11 Filter

RxF10 Filter

RxF9 Filter

RxF8 Filter

RxF7 Filter

RxF6 Filter

RxF5 Filter

RxF4 Filter

RxF3 Filter

RxF2 Filter

RxF1 Filter

RxF0 Filter

RxM1 Mask

RxM0 Mask

Control

Configuration

Logic

CPU

Bus

Interrupts

TRB0 TX/RX Buffer Control Register

DMA Controller

RxF15 Filter

RxM2 Mask

TRB7 TX/RX Buffer Control Register

TRB6 TX/RX Buffer Control Register

TRB5 TX/RX Buffer Control Register

TRB4 TX/RX Buffer Control Register

TRB3 TX/RX Buffer Control Register

TRB2 TX/RX Buffer Control Register

TRB1 TX/RX Buffer Control Register

Transmit Byte

Sequencer

Message Assembly

Buffer

Note: x = 1 or 2.

 2009-2012 Microchip Technology Inc. DS70616G-page 361

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

21.2 Modes of Operation

The ECANx module can operate in one of several

operation modes selected by the user. These modes

include:

• Initialization mode

• Disable mode

• Normal Operation mode

• Listen Only mode

• Listen All Messages mode

• Loopback mode

Modes are requested by setting the REQOP<2:0> bits

(CxCTRL1<10:8>). Entry into a mode is Acknowledged

by monitoring the OPMODE<2:0> bits (CxCTRL1<7:5>).

The module does not change the mode and the

OPMODE bits until a change in mode is acceptable,

generally during bus Idle time, which is defined as at least

11 consecutive recessive bits.

21.3 ECAN Resources

Many useful resources related to ECAN are provided

on the main product page of the Microchip web site for

the devices listed in this data sheet. This product page,

which can be accessed using this link, contains the

latest updates and additional information.

21.3.1 KEY RESOURCES

•Section 21. “Enhanced Controller Area

Network (ECAN™)” (DS70353) in the

“dsPIC33E/PIC24E Family Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 362  2009-2012 Microchip Technology Inc.

21.4 ECANx Control Registers

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-1 R/W-0 R/W-0

—— CSIDL ABAT CANCKS REQOP<2:0>

bit 15 bit 8

R-1 R-0 R-0 U-0 R/W-0 U-0 U-0 R/W-0

OPMODE<2:0> —CANCAP ——WIN

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13 CSIDL: ECANx Stop in Idle Mode bit

1 = Discontinues module operation when device enters Idle mode

0 = Continues module operation in Idle mode

bit 12 ABAT: Abort All Pending Transmissions bit

1 = Signals all transmit buffers to abort transmission

0 = Module will clear this bit when all transmissions are aborted

bit 11 CANCKS: ECANx Module Clock (FCAN) Source Select bit

1 = FCAN is equal to twice FP

0 = FCAN is equal to FP

bit 10-8 REQOP<2:0>: Request Operation Mode bits

111 = Set Listen All Messages mode

110 = Reserved

101 = Reserved

100 = Set Configuration mode

011 = Set Listen Only Mode

010 = Set Loopback mode

001 = Set Disable mode

000 = Set Normal Operation mode

bit 7-5 OPMODE<2:0>: Operation Mode bits

111 = Module is in Listen All Messages mode

110 = Reserved

101 = Reserved

100 = Module is in Configuration mode

011 = Module is in Listen Only mode

010 = Module is in Loopback mode

001 = Module is in Disable mode

000 = Module is in Normal Operation mode

bit 4 Unimplemented: Read as ‘0’

bit 3 CANCAP: CAN Message Receive Timer Capture Event Enable bit

1 = Enables input capture based on CAN message receive

0 = Disables CAN capture

bit 2-1 Unimplemented: Read as ‘0’

bit 0 WIN: SFR Map Window Select bit

1 = Uses filter window

0 = Uses buffer window

 2009-2012 Microchip Technology Inc. DS70616G-page 363

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 U-0 U-0 R-0 R-0 R-0 R-0 R-0

— — — DNCNT<4:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-5 Unimplemented: Read as ‘0’

bit 4-0 DNCNT<4:0>: DeviceNet™ Filter Bit Number bits

10010-11111 = Invalid selection

10001 = Compares up to Data Byte 3, bit 6 with EID<17>

•

00001 = Compares up to Data Byte 1, bit 7 with EID<0>

00000 = Does not compare data bytes

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 364  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 R-0 R-0 R-0 R-0 R-0

— — — FILHIT<4:0>

bit 15 bit 8

U-0 R-1 R-0 R-0 R-0 R-0 R-0 R-0

—ICODE<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-13 Unimplemented: Read as ‘0’

bit 12-8 FILHIT<4:0>: Filter Hit Number bits

10000-11111 = Reserved

01111 = Filter 15

•

00001 = Filter 1

00000 = Filter 0

bit 7 Unimplemented: Read as ‘0’

bit 6-0 ICODE<6:0>: Interrupt Flag Code bits

1000101-1111111 = Reserved

1000100 = FIFO almost full interrupt

1000011 = Receiver overflow interrupt

1000010 = Wake-up interrupt

1000001 = Error interrupt

1000000 = No interrupt

•

0010000-0111111 = Reserved

0001111 = RB15 buffer interrupt

•

0001001 = RB9 buffer interrupt

0001000 = RB8 buffer interrupt

0000111 = TRB7 buffer interrupt

0000110 = TRB6 buffer interrupt

0000101 = TRB5 buffer interrupt

0000100 = TRB4 buffer interrupt

0000011 = TRB3 buffer interrupt

0000010 = TRB2 buffer interrupt

0000001 = TRB1 buffer interrupt

0000000 = TRB0 Buffer interrupt

 2009-2012 Microchip Technology Inc. DS70616G-page 365

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0

DMABS<2:0> — — — — —

bit 15 bit 8

U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— — — FSA<4:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-13 DMABS<2:0>: DMA Buffer Size bits

111 = Reserved

110 = 32 buffers in DMA RAM

101 = 24 buffers in DMA RAM

100 = 16 buffers in DMA RAM

011 = 12 buffers in DMA RAM

010 = 8 buffers in DMA RAM

001 = 6 buffers in DMA RAM

000 = 4 buffers in DMA RAM

bit 12-5 Unimplemented: Read as ‘0’

bit 4-0 FSA<4:0>: FIFO Area Starts with Buffer bits

11111 = Read Buffer RB31

11110 = Read Buffer RB30

•

00001 = TX/RX Buffer TRB1

00000 = TX/RX Buffer TRB0

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 366  2009-2012 Microchip Technology Inc.

U-0 U-0 R-0 R-0 R-0 R-0 R-0 R-0

—— FBP<5:0>

bit 15 bit 8

U-0 U-0 R-0 R-0 R-0 R-0 R-0 R-0

—— FNRB<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-8 FBP<5:0>: FIFO Buffer Pointer bits

011111 = RB31 buffer

011110 = RB30 buffer

•

000001 = TRB1 buffer

000000 = TRB0 buffer

bit 7-6 Unimplemented: Read as ‘0’

bit 5-0 FNRB<5:0>: FIFO Next Read Buffer Pointer bits

011111 = RB31 buffer

011110 = RB30 buffer

•

000001 = TRB1 buffer

000000 = TRB0 buffer

 2009-2012 Microchip Technology Inc. DS70616G-page 367

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 R-0 R-0 R-0 R-0 R-0 R-0

—— TXBO TXBP RXBP TXWAR RXWAR EWARN

bit 15 bit 8

R/C-0 R/C-0 R/C-0 U-0 R/C-0 R/C-0 R/C-0 R/C-0

IVRIF WAKIF ERRIF — FIFOIF RBOVIF RBIF TBIF

bit 7 bit 0

Legend: C = Writable bit, but only ‘0’ can be written to clear the bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13 TXBO: Transmitter in Error State Bus Off bit

1 = Transmitter is in Bus Off state

0 = Transmitter is not in Bus Off state

bit 12 TXBP: Transmitter in Error State Bus Passive bit

1 = Transmitter is in Bus Passive state

0 = Transmitter is not in Bus Passive state

bit 11 RXBP: Receiver in Error State Bus Passive bit

1 = Receiver is in Bus Passive state

0 = Receiver is not in Bus Passive state

bit 10 TXWAR: Transmitter in Error State Warning bit

1 = Transmitter is in Error Warning state

0 = Transmitter is not in Error Warning state

bit 9 RXWAR: Receiver in Error State Warning bit

1 = Receiver is in Error Warning state

0 = Receiver is not in Error Warning state

bit 8 EWARN: Transmitter or Receiver in Error State Warning bit

1 = Transmitter or Receiver is in Error State Warning state

0 = Transmitter or Receiver is not in Error State Warning state

bit 7 IVRIF: Invalid Message Interrupt Flag bit

1 = Interrupt Request has occurred

0 = Interrupt Request has not occurred

bit 6 WAKIF: Bus Wake-up Activity Interrupt Flag bit

1 = Interrupt Request has occurred

0 = Interrupt Request has not occurred

bit 5 ERRIF: Error Interrupt Flag bit (multiple sources in CxINTF<13:8> register)

1 = Interrupt Request has occurred

0 = Interrupt Request has not occurred

bit 4 Unimplemented: Read as ‘0’

bit 3 FIFOIF: FIFO Almost Full Interrupt Flag bit

1 = Interrupt Request has occurred

0 = Interrupt Request has not occurred

bit 2 RBOVIF: RX Buffer Overflow Interrupt Flag bit

1 = Interrupt Request has occurred

0 = Interrupt Request has not occurred

bit 1 RBIF: RX Buffer Interrupt Flag bit

1 = Interrupt Request has occurred

0 = Interrupt Request has not occurred

bit 0 TBIF: TX Buffer Interrupt Flag bit

1 = Interrupt Request has occurred

0 = Interrupt Request has not occurred

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 368  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0

IVRIE WAKIE ERRIE — FIFOIE RBOVIE RBIE TBIE

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 IVRIE: Invalid Message Interrupt Enable bit

1 = Interrupt request is enabled

0 = Interrupt request is not enabled

bit 6 WAKIE: Bus Wake-up Activity Interrupt Enable bit

1 = Interrupt request is enabled

0 = Interrupt request is not enabled

bit 5 ERRIE: Error Interrupt Enable bit

1 = Interrupt request is enabled

0 = Interrupt request is not enabled

bit 4 Unimplemented: Read as ‘0’

bit 3 FIFOIE: FIFO Almost Full Interrupt Enable bit

1 = Interrupt request is enabled

0 = Interrupt request is not enabled

bit 2 RBOVIE: RX Buffer Overflow Interrupt Enable bit

1 = Interrupt request is enabled

0 = Interrupt request is not enabled

bit 1 RBIE: RX Buffer Interrupt Enable bit

1 = Interrupt request is enabled

0 = Interrupt request is not enabled

bit 0 TBIE: TX Buffer Interrupt Enable bit

1 = Interrupt request is enabled

0 = Interrupt request is not enabled

 2009-2012 Microchip Technology Inc. DS70616G-page 369

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

TERRCNT<7:0>

bit 15 bit 8

R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

RERRCNT<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 TERRCNT<7:0>: Transmit Error Count bits

bit 7-0 RERRCNT<7:0>: Receive Error Count bits

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SJW<1:0> BRP<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7-6 SJW<1:0>: Synchronization Jump Width bits

11 = Length is 4 x TQ

10 = Length is 3 x TQ

01 = Length is 2 x TQ

00 = Length is 1 x TQ

bit 5-0 BRP<5:0>: Baud Rate Prescaler bits

11 1111 = TQ = 2 x 64 x 1/FCAN

•

00 0010 = TQ = 2 x 3 x 1/FCAN

00 0001 = TQ = 2 x 2 x 1/FCAN

00 0000 = TQ = 2 x 1 x 1/FCAN

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 370  2009-2012 Microchip Technology Inc.

U-0 R/W-x U-0 U-0 U-0 R/W-x R/W-x R/W-x

— WAKFIL — — — SEG2PH<2:0>

bit 15 bit 8

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

SEG2PHTS SAM SEG1PH<2:0> PRSEG<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14 WAKFIL: Select CAN Bus Line Filter for Wake-up bit

1 = Uses CAN bus line filter for wake-up

0 = CAN bus line filter is not used for wake-up

bit 13-11 Unimplemented: Read as ‘0’

bit 10-8 SEG2PH<2:0>: Phase Segment 2 bits

111 = Length is 8 x TQ

•

000 = Length is 1 x TQ

bit 7 SEG2PHTS: Phase Segment 2 Time Select bit

1 = Freely programmable

0 = Maximum of SEG1PH bits or Information Processing Time (IPT), whichever is greater

bit 6 SAM: Sample of the CAN Bus Line bit

1 = Bus line is sampled three times at the sample point

0 = Bus line is sampled once at the sample point

bit 5-3 SEG1PH<2:0>: Phase Segment 1 bits

111 = Length is 8 x TQ

•

000 = Length is 1 x TQ

bit 2-0 PRSEG<2:0>: Propagation Time Segment bits

111 = Length is 8 x TQ

•

000 = Length is 1 x TQ

 2009-2012 Microchip Technology Inc. DS70616G-page 371

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1

FLTEN15 FLTEN14 FLTEN13 FLTEN12 FLTEN11 FLTEN10 FLTEN9 FLTEN8

bit 15 bit 8

R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1

FLTEN7 FLTEN6 FLTEN5 FLTEN4 FLTEN3 FLTEN2 FLTEN1 FLTEN0

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 FLTENn: Enable Filter n to Accept Messages bits

1 = Enables Filter n

0 = Disables Filter n

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F3BP<3:0> F2BP<3:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F1BP<3:0> F0BP<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 F3BP<3:0>: RX Buffer Mask for Filter 3 bits

1111 = Filter hits received in RX FIFO buffer

1110 = Filter hits received in RX Buffer 14

•

0001 = Filter hits received in RX Buffer 1

0000 = Filter hits received in RX Buffer 0

bit 11-8 F2BP<3:0>: RX Buffer Mask for Filter 2 bits (same values as bit 15-12)

bit 7-4 F1BP<3:0>: RX Buffer Mask for Filter 1 bits (same values as bit 15-12)

bit 3-0 F0BP<3:0>: RX Buffer Mask for Filter 0 bits (same values as bit 15-12)

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 372  2009-2012 Microchip Technology Inc.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F7BP<3:0> F6BP<3:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F5BP<3:0> F4BP<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 F7BP<3:0>: RX Buffer Mask for Filter 7 bits

1111 = Filter hits received in RX FIFO buffer

1110 = Filter hits received in RX Buffer 14

•

0001 = Filter hits received in RX Buffer 1

0000 = Filter hits received in RX Buffer 0

bit 11-8 F6BP<3:0>: RX Buffer Mask for Filter 6 bits (same values as bit 15-12)

bit 7-4 F5BP<3:0>: RX Buffer Mask for Filter 5 bits (same values as bit 15-12)

bit 3-0 F4BP<3:0>: RX Buffer Mask for Filter 4 bits (same values as bit 15-12)

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F11BP<3:0> F10BP<3:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F9BP<3:0> F8BP<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 F11BP<3:0>: RX Buffer Mask for Filter 11 bits

1111 = Filter hits received in RX FIFO buffer

1110 = Filter hits received in RX Buffer 14

•

0001 = Filter hits received in RX Buffer 1

0000 = Filter hits received in RX Buffer 0

bit 11-8 F10BP<3:0>: RX Buffer Mask for Filter 10 bits (same values as bit 15-12)

bit 7-4 F9BP<3:0>: RX Buffer Mask for Filter 9 bits (same values as bit 15-12)

bit 3-0 F8BP<3:0>: RX Buffer Mask for Filter 8 bits (same values as bit 15-12)

 2009-2012 Microchip Technology Inc. DS70616G-page 373

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F15BP<3:0> F14BP<3:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F13BP<3:0> F12BP<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 F15BP<3:0>: RX Buffer Mask for Filter 15 bits

1111 = Filter hits received in RX FIFO buffer

1110 = Filter hits received in RX Buffer 14

•

0001 = Filter hits received in RX Buffer 1

0000 = Filter hits received in RX Buffer 0

bit 11-8 F14BP<3:0>: RX Buffer Mask for Filter 14 bits (same values as bit 15-12)

bit 7-4 F13BP<3:0>: RX Buffer Mask for Filter 13 bits (same values as bit 15-12)

bit 3-0 F12BP<3:0>: RX Buffer Mask for Filter 12 bits (same values as bit 15-12)

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 374  2009-2012 Microchip Technology Inc.

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

SID10 SID9 SID8 SID7 SID6 SID5 SID4 SID3

bit 15 bit 8

R/W-x R/W-x R/W-x U-0 R/W-x U-0 R/W-x R/W-x

SID2 SID1 SID0 —EXIDE —EID17EID16

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-5 SID<10:0>: Standard Identifier bits

1 = Message address bit, SIDx, must be ‘1’ to match filter

0 = Message address bit, SIDx, must be ‘0’ to match filter

bit 4 Unimplemented: Read as ‘0’

bit 3 EXIDE: Extended Identifier Enable bit

If MIDE = 1:

1 = Matches only messages with extended identifier addresses

0 = Matches only messages with standard identifier addresses

If MIDE = 0:

Ignores EXIDE bit.

bit 2 Unimplemented: Read as ‘0’

bit 1-0 EID<17:16>: Extended Identifier bits

1 = Message address bit, EIDx, must be ‘1’ to match filter

0 = Message address bit, EIDx, must be ‘0’ to match filter

 2009-2012 Microchip Technology Inc. DS70616G-page 375

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

EID15 EID14 EID13 EID12 EID11 EID10 EID9 EID8

bit 15 bit 8

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

EID7 EID6 EID5 EID4 EID3 EID2 EID1 EID0

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 EID<15:0>: Extended Identifier bits

1 = Message address bit, EIDx, must be ‘1’ to match filter

0 = Message address bit, EIDx, must be ‘0’ to match filter

ECAN

FILTER 7-0 MASK SELECTION REGISTER

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F7MSK<1:0> F6MSK<1:0> F5MSK<1:0> F4MSK<1:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F3MSK<1:0> F2MSK<1:0> F1MSK<1:0> F0MSK<1:0>

bit 7 bit 0

Legend: C = Writable bit, but only ‘0’ can be written to clear the bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 F7MSK<1:0>: Mask Source for Filter 7 bit

11 = Reserved

10 = Acceptance Mask 2 registers contain mask

01 = Acceptance Mask 1 registers contain mask

00 = Acceptance Mask 0 registers contain mask

bit 13-12 F6MSK<1:0>: Mask Source for Filter 6 bit (same values as bit 15-14)

bit 11-10 F5MSK<1:0>: Mask Source for Filter 5 bit (same values as bit 15-14)

bit 9-8 F4MSK<1:0>: Mask Source for Filter 4 bit (same values as bit 15-14)

bit 7-6 F3MSK<1:0>: Mask Source for Filter 3 bit (same values as bit 15-14)

bit 5-4 F2MSK<1:0>: Mask Source for Filter 2 bit (same values as bit 15-14)

bit 3-2 F1MSK<1:0>: Mask Source for Filter 1 bit (same values as bit 15-14)

bit 1-0 F0MSK<1:0>: Mask Source for Filter 0 bit (same values as bit 15-14)

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 376  2009-2012 Microchip Technology Inc.

ECAN

FILTER 15-8 MASK SELECTION REGISTER

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F15MSK<1:0> F14MSK<1:0> F13MSK<1:0> F12MSK<1:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

F11MSK<1:0> F10MSK<1:0> F9MSK<1:0> F8MSK<1:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 F15MSK<1:0>: Mask Source for Filter 15 bit

11 = Reserved

10 = Acceptance Mask 2 registers contain mask

01 = Acceptance Mask 1 registers contain mask

00 = Acceptance Mask 0 registers contain mask

bit 13-12 F14MSK<1:0>: Mask Source for Filter 14 bit (same values as bit 15-14)

bit 11-10 F13MSK<1:0>: Mask Source for Filter 13 bit (same values as bit 15-14)

bit 9-8 F12MSK<1:0>: Mask Source for Filter 12 bit (same values as bit 15-14)

bit 7-6 F11MSK<1:0>: Mask Source for Filter 11 bit (same values as bit 15-14)

bit 5-4 F10MSK<1:0>: Mask Source for Filter 10 bit (same values as bit 15-14)

bit 3-2 F9MSK<1:0>: Mask Source for Filter 9 bit (same values as bit 15-14)

bit 1-0 F8MSK<1:0>: Mask Source for Filter 8 bit (same values as bit 15-14)

 2009-2012 Microchip Technology Inc. DS70616G-page 377

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

ECAN

ACCEPTANCE FILTER MASK n STANDARD IDENTIFIER

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

SID10 SID9 SID8 SID7 SID6 SID5 SID4 SID3

bit 15 bit 8

R/W-x R/W-x R/W-x U-0 R/W-x U-0 R/W-x R/W-x

SID2 SID1 SID0 —MIDE —EID17EID16

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-5 SID<10:0>: Standard Identifier bits

1 = Includes bit, SIDx, in filter comparison

0 = Bit, SIDx, is a don’t care in filter comparison

bit 4 Unimplemented: Read as ‘0’

bit 3 MIDE: Identifier Receive Mode bit

1 = Matches only message types (standard or extended address) that correspond to EXIDE bit in filter

0 = Matches either standard or extended address message if filters match

(i.e., if (Filter SID) = (Message SID) or if (Filter SID/EID) = (Message SID/EID))

bit 2 Unimplemented: Read as ‘0’

bit 1-0 EID<17:16>: Extended Identifier bits

1 = Includes bit, EIDx, in filter comparison

0 = Bit, EIDx, is a don’t care in filter comparison

ECAN

ACCEPTANCE FILTER MASK n EXTENDED IDENTIFIER

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

EID15 EID14 EID13 EID12 EID11 EID10 EID9 EID8

bit 15 bit 8

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

EID7 EID6 EID5 EID4 EID3 EID2 EID1 EID0

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 EID<15:0>: Extended Identifier bits

1 = Includes bit, EIDx, in filter comparison

0 = Bit, EIDx, is a don’t care in filter comparison

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 378  2009-2012 Microchip Technology Inc.

R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0

RXFUL15 RXFUL14 RXFUL13 RXFUL12 RXFUL11 RXFUL10 RXFUL9 RXFUL8

bit 15 bit 8

R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0

RXFUL7 RXFUL6 RXFUL5 RXFUL4 RXFUL3 RXFUL2 RXFUL1 RXFUL0

bit 7 bit 0

Legend: C = Writable bit, but only ‘0’ can be written to clear the bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 RXFUL<15:0>: Receive Buffer n Full bits

1 = Buffer is full (set by module)

0 = Buffer is empty (cleared by user software)

R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0

RXFUL31 RXFUL30 RXFUL29 RXFUL28 RXFUL27 RXFUL26 RXFUL25 RXFUL24

bit 15 bit 8

R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0

RXFUL23 RXFUL22 RXFUL21 RXFUL20 RXFUL19 RXFUL18 RXFUL17 RXFUL16

bit 7 bit 0

Legend: C = Writable bit, but only ‘0’ can be written to clear the bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 RXFUL<31:16>: Receive Buffer n Full bits

1 = Buffer is full (set by module)

0 = Buffer is empty (cleared by user software)

 2009-2012 Microchip Technology Inc. DS70616G-page 379

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0

RXOVF15 RXOVF14 RXOVF13 RXOVF12 RXOVF11 RXOVF10 RXOVF9 RXOVF8

bit 15 bit 8

R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0

RXOVF7 RXOVF6 RXOVF5 RXOVF4 RXOVF3 RXOVF2 RXOVF1 RXOVF0

bit 7 bit 0

Legend: C = Writable bit, but only ‘0’ can be written to clear the bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 RXOVF<15:0>: Receive Buffer n Overflow bits

1 = Module attempted to write to a full buffer (set by module)

0 = No overflow condition (cleared by user software)

R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0

RXOVF31 RXOVF30 RXOVF29 RXOVF28 RXOVF27 RXOVF26 RXOVF25 RXOVF24

bit 15 bit 8

R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0

RXOVF23 RXOVF22 RXOVF21 RXOVF20 RXOVF19 RXOVF18 RXOVF17 RXOVF16

bit 7 bit 0

Legend: C = Writable bit, but only ‘0’ can be written to clear the bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 RXOVF<31:16>: Receive Buffer n Overflow bits

1 = Module attempted to write to a full buffer (set by module)

0 = No overflow condition (cleared by user software)

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 380  2009-2012 Microchip Technology Inc.

(m = 0, 2, 4, 6; n = 1, 3, 5, 7)

R/W-0 R-0 R-0 R-0 R/W-0 R/W-0 R/W-0 R/W-0

TXENn TXABTn TXLARBn TXERRn TXREQn RTRENn TXnPRI<1:0>

bit 15 bit 8

R/W-0 R-0 R-0 R-0 R/W-0 R/W-0 R/W-0 R/W-0

TXENm TXABTm(1)TXLARBm(1)TXERRm(1)TXREQm RTRENm TXmPRI<1:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 See definition for bits 7-0, controls Buffer n

bit 7 TXENm: TX/RX Buffer Selection bit

1 = Buffer TRBn is a transmit buffer

0 = Buffer TRBn is a receive buffer

bit 6 TXABTm: Message Aborted bit(1)

1 = Message was aborted

0 = Message completed transmission successfully

bit 5 TXLARBm: Message Lost Arbitration bit(1)

1 = Message lost arbitration while being sent

0 = Message did not lose arbitration while being sent

bit 4 TXERRm: Error Detected During Transmission bit(1)

1 = A bus error occurred while the message was being sent

0 = A bus error did not occur while the message was being sent

bit 3 TXREQm: Message Send Request bit

1 = Requests that a message be sent; the bit automatically clears when the message is successfully sent

0 = Clearing the bit to ‘0’ while set requests a message abort

bit 2 RTRENm: Auto-Remote Transmit Enable bit

1 = When a remote transmit is received, TXREQm will be set

0 = When a remote transmit is received, TXREQm will be unaffected

bit 1-0 TXmPRI<1:0>: Message Transmission Priority bits

11 = Highest message priority

10 = High intermediate message priority

01 = Low intermediate message priority

00 = Lowest message priority

Note 1: This bit is cleared when TXREQm is set.

Note: The buffers, SID, EID, DLC, Data Field and Receive Status registers are located in DMA RAM.

 2009-2012 Microchip Technology Inc. DS70616G-page 381

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

21.5 ECAN Message Buffers

ECAN Message Buffers are part of DMA RAM memory.

They are not ECAN Special Function Registers. The

user application must directly write into the DMA RAM

area that is configured for ECAN Message Buffers. The

location and size of the buffer area is defined by the

user application.

BUFFER 21-1:

ECAN™

MESSAGE BUFFER WORD 0

U-0 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x

— — — SID10 SID9 SID8 SID7 SID6

bit 15 bit 8

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

SID5 SID4 SID3 SID2 SID1 SID0 SRR IDE

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-13 Unimplemented: Read as ‘0’

bit 12-2 SID<10:0>: Standard Identifier bits

bit 1 SRR: Substitute Remote Request bit

When TXIDE = 0:

1 = Message will request remote transmission

0 = Normal message

When TXIDE = 1:

The SRR bit must be set to ‘1’.

bit 0 IDE: Extended Identifier bit

1 = Message will transmit extended identifier

0 = Message will transmit standard identifier

BUFFER 21-2:

ECAN™

MESSAGE BUFFER WORD 1

U-0 U-0 U-0 U-0 R/W-x R/W-x R/W-x R/W-x

— — — —EID17EID16EID15EID14

bit 15 bit 8

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

EID13 EID12 EID11 EID10 EID9 EID8 EID7 EID6

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 Unimplemented: Read as ‘0’

bit 11-0 EID<17:6>: Extended Identifier bits

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 382  2009-2012 Microchip Technology Inc.

(

BUFFER 21-3:

ECAN™

MESSAGE BUFFER WORD 2

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

EID5 EID4 EID3 EID2 EID1 EID0 RTR RB1

bit 15 bit 8

U-x U-x U-x R/W-x R/W-x R/W-x R/W-x R/W-x

— — — RB0 DLC3 DLC2 DLC1 DLC0

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-10 EID<5:0>: Extended Identifier bits

bit 9 RTR: Remote Transmission Request bit

When TXIDE = 1:

1 = Message will request remote transmission

0 = Normal message

When TXIDE = 0:

The RTR bit is ignored.

bit 8 RB1: Reserved Bit 1

User must set this bit to ‘0’ per CAN protocol.

bit 7-5 Unimplemented: Read as ‘0’

bit 4 RB0: Reserved Bit 0

User must set this bit to ‘0’ per CAN protocol.

bit 3-0 DLC<3:0>: Data Length Code bits

BUFFER 21-4: ECAN

™

MESSAGE BUFFER WORD 3

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

Byte 1

bit 15 bit 8

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

Byte 0

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Byte 1<15:8>: ECAN Message Byte 0

bit 7-0 Byte 0<7:0>: ECAN Message Byte 1

 2009-2012 Microchip Technology Inc. DS70616G-page 383

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

BUFFER 21-5: ECAN

™

MESSAGE BUFFER WORD 4

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

Byte 3

bit 15 bit 8

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

Byte 2

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Byte 3<15:8>: ECAN Message Byte 3

bit 7-0 Byte 2<7:0>: ECAN Message Byte 2

BUFFER 21-6: ECAN

™

MESSAGE BUFFER WORD 5

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

Byte 5

bit 15 bit 8

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

Byte 4

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Byte 5<15:8>: ECAN Message Byte 5

bit 7-0 Byte 4<7:0>: ECAN Message Byte 4

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 384  2009-2012 Microchip Technology Inc.

BUFFER 21-7: ECAN

™

MESSAGE BUFFER WORD 6

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

Byte 7

bit 15 bit 8

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

Byte 6

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Byte 7<15:8>: ECAN Message Byte 7

bit 7-0 Byte 6<7:0>: ECAN Message Byte 6

BUFFER 21-8:

ECAN™

MESSAGE BUFFER WORD 7

U-0 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x

— — — FILHIT<4:0>(1)

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-13 Unimplemented: Read as ‘0’

bit 12-8 FILHIT<4:0>: Filter Hit Code bits(1)

Encodes the number of the filter that resulted in writing this buffer.

bit 7-0 Unimplemented: Read as ‘0’

Note 1: Only written by the module for receive buffers, unused for transmit buffers.

 2009-2012 Microchip Technology Inc. DS70616G-page 385

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

22.0 USB ON-THE-GO (OTG)

MODULE (dsPIC33EPXXXMU8XX

AND PIC24EPGU8XX DEVICES

ONLY)

22.1 Overview

The Universal Serial Bus (USB) On-The-Go (OTG)

module includes the following features:

• USB Full-Speed Support for Host and Device

• Low-Speed Host Support

• USB On-The-Go Support

• Integrated Signaling Resistors

• Integrated Analog Comparators for VBUS

Monitoring

• Integrated USB Transceiver

• Hardware Performs Transaction Handshaking

• Endpoint Buffering Anywhere in System RAM

• Integrated DMA Controller to Access System

RAM

• Support for all four transfer types:

- Control

- Interrupt

-Bulk Data

- Isochronous

• Queueing of up to Four Endpoint Transfers

without Servicing

• USB 5V Charge Pump Controller

The USB module contains the analog and digital

components to provide a USB 2.0 full-speed and low-

speed embedded host, full-speed device or OTG

implementation with a minimum of external

components.

The USB module consists of the clock generator, the

USB voltage comparators, the transceiver, the Serial

Interface Engine (SIE), pull-up and pull-down resistors,

and the register interface. Figure 22-1 illustrates the

block diagram of the USB OTG module.

The device auxiliary clock generator provides the

48 MHz clock required for USB communication. The

voltage comparators monitor the voltage on the VBUS

pin to determine the state of the bus. The transceiver

provides the analog translation between the USB bus

and the digital logic. The SIE is a state machine that

transfers data to and from the endpoint buffers and

generates the protocol for data transfers. The

integrated pull-up and pull-down resistors eliminate the

need for external signaling components. The register

interface allows the CPU to configure and

communicate with the module.

22.2 Clearing USB OTG Interrupts

Unlike device level interrupts, the USB OTG interrupt

status flags are not freely writable in software. All USB

OTG flag bits are implemented as hardware set-only

bits. Additionally, these bits can only be cleared in

software by writing a ‘1’ to their locations (i.e.,

performing a BSET instruction). Writing a ‘0’ to a flag bit

(i.e., a BCLR instruction) has no effect.

Note 1: This data sheet is not intended to be a

comprehensive reference source. To com-

plement the information in this data sheet,

refer to Section 25. “USB On-The-Go

(OTG)” (DS70571) of the “dsPIC33E/

PIC24E Family Reference Manual”, which

is available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information. Note: The implementation and use of the USB

specifications and other third party

specifications or technology may require a

license from various entities, including,

but not limited to USB Implementers

Forum, Inc. (also referred to as USB-IF). It

is your responsibility to obtain more

information regarding any applicable

licensing obligations.

Note: Throughout this section, a bit that can only

be cleared by writing a ‘1’ to its location is

referred to as “Write ‘1’ to clear bit”. In reg-

ister descriptions, this function is indicated

by the descriptor, “K”.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 386  2009-2012 Microchip Technology Inc.

FIGURE 22-1: USB INTERFACE DIAGRAM

48 MHz USB Clock

VUSB3V3

D+

D-

VBUS

VBUSON

SRP Charge

SRP Discharge

Registers

and

Control

Interface

System

RAM

Full-Speed Pull-up

Host Pull-down

Host Pull-Down

USBID

VMIO

VCPCON

from Auxiliary PLL

Low-Speed Pull-up

VBUSST

VPIO

DMH

DPH

DMLN

DPLN

RCV

USBOEN

External Transceiver Interface

VCMPST3

VCMPST2

VCMPST1

External

VBUS

Comparator

Interface

SIE

USB

Transceiver

Comparators

USB

Voltage

VBUS Boost

Controller

 2009-2012 Microchip Technology Inc. DS70616G-page 387

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

22.3 USB OTG Resources

Many useful resources related to USB OTG are

provided on the main product page of the Microchip

web site for the devices listed in this data sheet. This

product page, which can be accessed using this link,

contains the latest updates and additional information.

22.3.1 KEY RESOURCES

•Section 11. “USB On-The-Go (OTG)”

(DS70571) in the “dsPIC33E/PIC24E Family

Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 388  2009-2012 Microchip Technology Inc.

22.4 USB Control Registers

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R-0, HSC U-0 R-0, HSC U-0 R-0, HSC R-0, HSC U-0 R-0, HSC

ID —LSTATE— SESVD SESEND — VBUSVD

bit 7 bit 0

Legend: U = Unimplemented bit, read as ‘0’

R = Readable bit W = Writable bit HSC = Hardware Settable/Clearable bit

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 ID: ID Pin State Indicator bit

1 = No cable is attached or a Type B plug has been plugged into the USB receptacle

0 = A Type A plug has been plugged into the USB receptacle

bit 6 Unimplemented: Read as ‘0’

bit 5 LSTATE: Line State Stable Indicator bit

1 = The USB line state (as defined by SE0 and JSTATE) has been stable for the previous 1 ms

0 = The USB line state has NOT been stable for the previous 1 ms

bit 4 Unimplemented: Read as ‘0’

bit 3 SESVD: Session Valid Indicator bit

1 = The VBUS voltage is above VA_SESS_VLD (as defined in the USB OTG Specification) on the A or B

device

0 = The VBUS voltage is below VA_SESS_VLD on the A or B device

bit 2 SESEND: B-Session End Indicator bit

1 = The VBUS voltage is below VB_SESS_END (as defined in the USB OTG Specification) on the B device

0 = The VBUS voltage is above VB_SESS_END on the B device

bit 1 Unimplemented: Read as ‘0’

bit 0 VBUSVD: A-VBUS Valid Indicator bit

1 = The VBUS voltage is above VA_VBUS_VLD (as defined in the USB OTG Specification) on the A device

0 = The VBUS voltage is below VA_VBUS_VLD on the A device

 2009-2012 Microchip Technology Inc. DS70616G-page 389

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

DPPULUP DMPULUP DPPULDWN

(1)

DMPULDWN

(1)

VBUSON

(

)

OTGEN

(

)

VBUSCHG

(

)

VBUSDIS

(

)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 DPPULUP: D+ Pull-Up Enable bit

1 = D+ data line pull-up resistor is enabled

0 = D+ data line pull-up resistor is disabled

bit 6 DMPULUP: D- Pull-Up Enable bit

1 = D- data line pull-up resistor is enabled

0 = D- data line pull-up resistor is disabled

bit 5 DPPULDWN: D+ Pull-Down Enable bit

(

)

1 = D+ data line pull-down resistor is enabled

0 = D+ data line pull-down resistor is disabled

bit 4 DMPULDWN: D- Pull-Down Enable bit

(

)

1 = D- data line pull-down resistor is enabled

0 = D- data line pull-down resistor is disabled

bit 3 VBUSON: VBUS Power-on bit

(

)

1 =VBUS line is powered

0 =V

BUS line is not powered

bit 2 OTGEN: OTG Features Enable bit

(

)

1 = USB OTG is enabled; all D+/D- pull-ups and pull-downs are enabled

0 = USB OTG is disabled; D+/D- pull-ups and pull-downs are controlled in hardware by the settings of

the HOSTEN and USBEN bits (UxCON<3,0>)

bit 1 VBUSCHG: VBUS Charge Selection bit

(

)

1 =VBUS line is set to charge to 3.3V

0 =V

BUS line is set to charge to 5V

bit 0 VBUSDIS: VBUS Discharge Enable bit

(

)

1 =VBUS line is discharged through a resistor

0 =V

BUS line is not discharged

Note 1: These bits are only used in Host mode; do not use in Device mode.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 390  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

HS, HC U-0 U-0 R/W U-0 U-0 R/W-0, HC R/W-0

UACTPND — — USLPGRD — — USUSPND USBPWR(1)

bit 7 bit 0

Legend: HS = Hardware Settable bit HC = Hardware Clearable bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 UACTPND: USB Activity Pending bit

1 = Module should not be suspended at the moment (requires the USLPGRD bit to be set)

0 = Module may be suspended or powered down

bit 6-5 Unimplemented: Read as ‘0’

bit 4 USLPGRD: USB Sleep Guard bit

1 = Indicates to the USB module that it is about to be suspended or powered down

0 = No suspend

bit 3-2 Unimplemented: Read as ‘0’

bit 1 USUSPND: USB Suspend Mode Enable bit

1 = USB OTG module is in Suspend mode

0 = Normal USB OTG operation

bit 0 USBPWR: USB Operation Enable bit(1)

1 = USB OTG module is enabled

0 = USB OTG module is disabled

Note 1: Do not clear this bit unless the HOSTEN, USBEN and OTGEN bits (UxCON<3,0> and UxOTGCON<2>)

are also cleared.

 2009-2012 Microchip Technology Inc. DS70616G-page 391

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R-0, HSC R-0, HSC R-0, HSC R-0, HSC R-0, HSC R-0, HSC U-0 U-0

ENDPT<3:0>(2)DIR PPBI(1)— —

bit 7 bit 0

Legend: U = Unimplemented bit, read as ‘0’

R = Readable bit W = Writable bit HSC = Hardware Settable/Clearable bit

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7-4 ENDPT<3:0>: Last Endpoint Activity Number bits

(represents the number of the endpoint BDT updated by the last USB transfer)(2)

1111 = Endpoint 15

1110 = Endpoint 14

•

0001 = Endpoint 1

0000 = Endpoint 0

bit 3 DIR: Last Buffer Descriptor Direction Indicator bit

1 = The last transaction was a transmit transfer (TX)

0 = The last transaction was a receive transfer (RX)

bit 2 PPBI: Ping-Pong Buffer Descriptor Pointer Indicator bit(1)

1 = The last transaction was to the ODD buffer descriptor bank

0 = The last transaction was to the EVEN buffer descriptor bank

bit 1-0 Unimplemented: Read as ‘0’

Note 1: This bit is only valid for endpoints with available EVEN and ODD buffer descriptor registers.

2: In Host mode, all transactions are processed through Endpoint 0 and the Endpoint 0 BDTs. Therefore,

ENDPT<3:0> will always read as ‘0000’.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 392  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 R-x, HSC R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0

— SE0 PKTDIS —HOSTEN

(1)RESUME PPBRST USBEN

bit 7 bit 0

Legend: U = Unimplemented bit, read as ‘0’

R = Readable bit W = Writable bit HSC = Hardware Settable/Clearable bit

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-7 Unimplemented: Read as ‘0’

bit 6 SE0: Live Single-Ended Zero Flag bit

1 = Single-ended zero is active on the USB bus

0 = No single-ended zero is detected

bit 5 PKTDIS: Packet Transfer Disable bit

1 = SIE token and packet processing are disabled; automatically set when a SETUP token is received

0 = SIE token and packet processing are enabled

bit 4 Unimplemented: Read as ‘0’

bit 3 HOSTEN: USB Host Mode Enable bit(1)

1 = USB host capability is enabled; pull-downs on D+ and D- are activated in hardware

0 = USB host capability is disabled

bit 2 RESUME: USB Resume Signaling Enable bit

1 = Resume signaling is activated

0 = Resume signaling is disabled

bit 1 PPBRST: Ping-Pong Buffers Reset bit

1 = Resets all Ping-Pong Buffer Pointers to the EVEN buffer descriptor banks

0 = Ping-Pong Buffer Pointers are not reset

bit 0 USBEN: USB Module Enable bit

1 = USB module and supporting circuitry are enabled (device attached); D+ pull-up is activated in hardware

0 = USB module and supporting circuitry are disabled (device detached)

Note 1: This bit should be ‘0’ in Device mode.

 2009-2012 Microchip Technology Inc. DS70616G-page 393

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R-x, HSC

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

JSTATE SE0 TOKBUSY USBRST HOSTEN RESUME PPBRST SOFEN

bit 7 bit 0

Legend: U = Unimplemented bit, read as ‘0’

R = Readable bit W = Writable bit HSC = Hardware Settable/Clearable bit

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 JSTATE: Live Differential Receiver J State Flag bit

1 = J state (differential ‘0’ in low-speed, differential ‘1’ in full-speed) is detected on the USB

0 = No J state is detected

bit 6 SE0: Live Single-Ended Zero Flag bit

1 = Single-ended zero is active on the USB bus

0 = No single-ended zero is detected

bit 5 TOKBUSY: Token Busy Status bit

1 = Token is being executed by the USB module in On-The-Go state

0 = No token is being executed

bit 4 USBRST: USB Reset bit

1 = USB Reset has been generated; for Software Reset, application must set this bit for 50 ms and

then clear it

0 = USB Reset is terminated

bit 3 HOSTEN: USB Host Mode Enable bit

1 = USB host capability is enabled; pull-downs on D+ and D- are activated in hardware

0 = USB host capability is disabled

bit 2 RESUME: USB Resume Signaling Enable bit

1 = Resume signaling is activated; software must set the bit for 10 ms and then clear to enable remote

wake-up

0 = Resume signaling is disabled

bit 1 PPBRST: Ping-Pong Buffers Reset bit

1 = Resets all Ping-Pong Buffer Pointers to the EVEN buffer descriptor banks

0 = Ping-Pong Buffer Pointers are not reset

bit 0 SOFEN: USB Start-of-Frame (SOF) Enable bit

1 = Start-of-Frame token is sent every one 1 ms

0 = Start-of-Frame token is disabled

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 394  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— ———————

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

LSPDEN

(1)

DEVADDR<6:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 LSPDEN: USB Low-Speed Enable Indicator bit(

)

1 = USB module operates at low-speed

0 = USB module operates at full-speed

bit 6-0 DEVADDR<6:0>: USB Device Address bits

Note 1: Host mode only. In Device mode, this bit is unimplemented.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PID<3:0>(1)EP<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7-4 PID<3:0>: Token Type Identifier bits(1)

1101 = SETUP (TX) token type transaction

1001 = IN (RX) token type transaction

0001 = OUT (TX) token type transaction

bit 3-0 EP<3:0>: Token Command Endpoint Address bits

This value must specify a valid endpoint on the attached device.

Note 1: All other combinations are reserved and are not to be used.

 2009-2012 Microchip Technology Inc. DS70616G-page 395

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

(HOST MODE ONLY)

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

CNT<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7-0 CNT<7:0>: Start-of-Frame Count bits

Value represents 10 + (packet size of n bytes); for example:

0100 1010 = 64-byte packet

0010 1010 = 32-byte packet

0001 0010 = 8-byte packet

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0

UTEYE UOEMON(1)— USBSIDL — — — —

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 UTEYE: USB Eye Pattern Test Enable bit

1 = Eye pattern test is enabled

0 = Eye pattern test is disabled

bit 6 UOEMON: USB OE Monitor Enable bit(1)

1 =OE signal is active;

it indicates intervals during which the D+/D- lines are driving

0 =

signal is inactive

(1)

bit 5 Unimplemented: Read as ‘0’

bit 4 USBSIDL: USB OTG Stop in Idle Mode bit

1 = Discontinues module operation when device enters Idle mode

0 = Continues module operation in Idle mode

bit 3-0 Unimplemented: Read as ‘0’

Note 1: When the UTRIS (UxCNFG2<0>) bit is set, the OE signal is active regardless of the setting of UOEMON.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 396  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— — UVCMPSEL PUVBUS EXTI2CEN

UVBUSDIS

(1)

UVCMPDIS

(1)

UTRDIS(

)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-6 Unimplemented: Read as ‘0’

bit 5 UVCMPSEL: USB External Comparator Input Mode Select bit

When UVCMPDIS is Set:

1 = Use 3-pin input for external comparators

0 = Use 2-pin input for external comparators

bit 4 PUVBUS: VBUS Pull-up Enable bit

1 = Pull-up on VBUS pin is enabled

0 = Pull-up on VBUS pin is disabled

bit 3 EXTI2CEN: I2C™ Interface for External Module Control Enable bit

1 = External module(s) controlled via I2C interface

0 = External module(s) controlled via dedicated pins

bit 2 UVBUSDIS: USB On-Chip 5V Boost Regulator Builder Disable bit(

)

1 = On-chip boost regulator builder is disabled; digital output control interface is enabled

0 = On-chip boost regulator builder is active

bit 1 UVCMPDIS: USB On-Chip VBUS Comparator Disable bit(

)

1 = On-chip charge VBUS comparator is disabled; digital input status interface is enabled

0 = On-chip charge VBUS comparator is active

bit 0 UTRDIS: USB On-Chip Transceiver Disable bit(

)

1 = On-chip transceiver is disabled; digital transceiver interface is enabled

0 = On-chip transceiver is active

Note 1: Do not change this bit while the USBPWR bit is set (UxPWRC<0> = 1).

 2009-2012 Microchip Technology Inc. DS70616G-page 397

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/K-0, HS R/K-0, HS R/K-0, HS R/K-0, HS R/K-0, HS R/K-0, HS U-0 R/K-0, HS

IDIF T1MSECIF LSTATEIF ACTVIF SESVDIF SESENDIF — VBUSVDIF

bit 7 bit 0

Legend: U = Unimplemented bit, read as ‘0’

R = Readable bit K = Write ‘1’ to clear bit HS = Hardware Settable bit

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 IDIF: ID State Change Indicator bit

1 = Change in ID state is detected

0 = No ID state change

bit 6 T1MSECIF: 1 Millisecond Timer bit

1 = The 1 millisecond timer has expired

0 = The 1 millisecond timer has not expired

bit 5 LSTATEIF: Line State Stable Indicator bit

1 = USB line state (as defined by the SE0 and JSTATE bits) has been stable for 1 ms, but different from

last time

0 = USB line state has not been stable for 1 ms

bit 4 ACTVIF: Bus Activity Indicator bit

1 = Activity on the D+/D- lines or VBUS is detected

0 = No activity on the D+/D- lines or VBUS is detected

bit 3 SESVDIF: Session Valid Change Indicator bit

1 =VBUS has crossed VA_SESS_VLD (as defined in the USB OTG Specification)(1)

0 =VBUS has not crossed VA_SESS_VLD

bit 2 SESENDIF: B-Device VBUS Change Indicator bit

1 =VBUS change on B-device is detected; VBUS has crossed VB_SESS_END (as defined in the USB

OTG Specification)(1)

0 =VBUS has not crossed VA_SESS_END

bit 1 Unimplemented: Read as ‘0’

bit 0 VBUSVDIF: A-Device VBUS Change Indicator bit

1 =VBUS change on A-device is detected; VBUS has crossed VA_VBUS_VLD (as defined in the USB

OTG Specification)(1)

0 =No VBUS change on A-device is detected

Note 1: VBUS threshold crossings may be either rising or falling.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 398  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0

IDIE T1MSECIE LSTATEIE ACTVIE SESVDIE SESENDIE — VBUSVDIE

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 IDIE: ID Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 6 T1MSECIE: 1 Millisecond Timer Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 5 LSTATEIE: Line State Stable Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 4 ACTVIE: Bus Activity Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 3 SESVDIE: Session Valid Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 2 SESENDIE: B-Device Session End Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 1 Unimplemented: Read as ‘0’

bit 0 VBUSVDIE: A-Device VBUS Valid Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

 2009-2012 Microchip Technology Inc. DS70616G-page 399

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/K-0, HS U-0 R/K-0, HS R/K-0, HS R/K-0, HS R/K-0, HS R-0 R/K-0, HS

STALLIF — RESUMEIF IDLEIF TRNIF SOFIF UERRIF URSTIF

bit 7 bit 0

Legend: U = Unimplemented bit, read as ‘0’

R = Readable bit K = Write ‘1’ to clear bit HS = Hardware Settable bit

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 STALLIF: STALL Handshake Interrupt bit

1 = A STALL handshake was sent by the peripheral during the handshake phase of the transaction in

Device mode

0 = A STALL handshake has not been sent

bit 6 Unimplemented: Read as ‘0’

bit 5 RESUMEIF: Resume Interrupt bit

1 = A K-State is observed on the D+ or D- pin for 2.5 s (differential ‘1’ for low speed, differential ‘0’ for

full speed)

0 = No K-State is observed

bit 4 IDLEIF: Idle Detect Interrupt bit

1 = Idle condition is detected (constant Idle state of 3 ms or more)

0 = No Idle condition is detected

bit 3 TRNIF: Token Processing Complete Interrupt bit

1 = Processing of current token is complete; read UxSTAT register for endpoint BDT information

0 = Processing of current token is not complete; clear UxSTAT register or load next token from STAT

(clearing this bit causes the the STAT FIFO to advance)

bit 2 SOFIF: Start-of-Frame Token Interrupt bit

1 = A Start-of-Frame token was received by the peripheral

0 = A Start-of-Frame token has not been received by the peripheral

bit 1 UERRIF: USB Error Condition Interrupt bit (read-only)

1 = An unmasked error condition has occurred; only error states enabled in the UxEIE register can set

this bit

0 = No unmasked error condition has occurred

bit 0 URSTIF: USB Reset Interrupt bit

1 = Valid USB Reset has occurred for at least 2.5 s; Reset state must be cleared before this bit can

be reasserted

0 = No USB Reset has occurred

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 400  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

————————

bit 15 bit 8

R/K-0, HS R/K-0, HS R/K-0, HS R/K-0, HS R/K-0, HS R/K-0, HS R-0 R/K-0, HS

STALLIF ATTACHIF RESUMEIF IDLEIF TRNIF SOFIF UERRIF DETACHIF

bit 7 bit 0

Legend: U = Unimplemented bit, read as ‘0’

R = Readable bit K = Write ‘1’ to clear bit HS = Hardware Settable bit

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 STALLIF: STALL Handshake Interrupt bit

1 = A STALL handshake was sent by the peripheral device during the handshake phase of the

transaction in Device mode

0 = A STALL handshake has not been sent

bit 6 ATTACHIF: Peripheral Attach Interrupt bit

1 = A peripheral attachment has been detected by the module; set if the bus state is not SE0 and there

has been no bus activity for 2.5 s

0 = No peripheral attachment is detected

bit 5 RESUMEIF: Resume Interrupt bit

1 = A K-State is observed on the D+ or D- pin for 2.5 s (differential ‘1’ for low speed, differential ‘0’ for

full speed)

0 = No K-State is observed

bit 4 IDLEIF: Idle Detect Interrupt bit

1 = Idle condition is detected (constant Idle state of 3 ms or more)

0 = No Idle condition is detected

bit 3 TRNIF: Token Processing Complete Interrupt bit

1 = Processing of current token is complete; read USTAT register for endpoint BDT information

0 = Processing of current token is not complete; clear USTAT register or load next token from STAT

bit 2 SOFIF: Start-of-Frame Token Interrupt bit

1 = Start-of-Frame threshold is reached by the host

0 = No Start-of-Frame token threshold is reached

bit 1 UERRIF: USB Error Condition Interrupt bit

1 = An unmasked error condition has occurred; only error states enabled in the UxEIE register can set

this bit

0 = No unmasked error condition has occurred

bit 0 DETACHIF: Detach Interrupt bit

1 = A peripheral detachment has been detected by the module

0 = No peripheral detachment has been detected

 2009-2012 Microchip Technology Inc. DS70616G-page 401

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

STALLIE — RESUMEIE IDLEIE TRNIE SOFIE UERRIE URSTIE

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 STALLIE: STALL Handshake Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 6 Unimplemented: Read as ‘0’

bit 5 RESUMEIE: Resume Interrupt bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 4 IDLEIE: Idle Detect Interrupt bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 3 TRNIE: Token Processing Complete Interrupt bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 2 SOFIE: Start-of-Frame Token Interrupt bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 1 UERRIE: USB Error Condition Interrupt bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 0 URSTIE: USB Reset Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 402  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

STALLIE ATTACHIE(1)RESUMEIE IDLEIE TRNIE SOFIE UERRIE DETACHIE

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 STALLIE: STALL Handshake Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 6 ATTACHIE: Peripheral Attach Interrupt bit(1)

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 5 RESUMEIE: Resume Interrupt bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 4 IDLEIE: Idle Detect Interrupt bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 3 TRNIE: Token Processing Complete Interrupt bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 2 SOFIE: Start-of-Frame Token Interrupt bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 1 UERRIE: USB Error Condition Interrupt bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 0 DETACHIE: USB Detach Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

Note 1: Unimplemented in OTG mode, read as ‘0’.

 2009-2012 Microchip Technology Inc. DS70616G-page 403

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/K-0, HS R/K-0,HS R/K-0, HS R/K-0, HS R/K-0, HS R/K-0, HS R/K-0, HS R/K-0, HS

BTSEF BUSACCEF DMAEF BTOEF DFN8EF CRC16EF CRC5EF PIDEF

bit 7 bit 0

Legend: U = Unimplemented bit, read as ‘0’

R = Readable bit K = Write ‘1’ to clear bit HS = Hardware Settable bit

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 BTSEF: Bit Stuff Error Flag bit

1 = Bit stuff error has been detected

0 = No bit stuff error has been detected

bit 6 BUSACCEF: Bus Access Error Flag bit

1 = Peripheral tried to access an unimplemented RAM location

0 = RAM location access was successful

bit 5 DMAEF: DMA Error Flag bit

1 = A USB DMA error condition is detected; the data size indicated by the buffer descriptor byte count

field is less than the number of received bytes; the received data is truncated

0 = No DMA error

bit 4 BTOEF: Bus Turnaround Time-out Error Flag bit

1 = Bus turnaround time-out has occurred

0 = No bus turnaround time-out has occurred

bit 3 DFN8EF: Data Field Size Error Flag bit

1 = Data field was not an integral number of bytes

0 = Data field was an integral number of bytes

bit 2 CRC16EF: CRC16 Failure Flag bit

1 = CRC16 failed

0 = CRC16 passed

bit 1 CRC5EF: CRC5 Host Error Flag bit

1 = Token packet rejected due to CRC5 error

0 = Token packet accepted (no CRC5 error)

bit 0 PIDEF: PID Check Failure Flag bit

1 = PID check failed

0 = PID check passed

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 404  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/K-0, HS R/K-0,HS R/K-0, HS R/K-0, HS R/K-0, HS R/K-0, HS R/K-0, HS R/K-0, HS

BTSEF BUSACCEF DMAEF BTOEF DFN8EF CRC16EF EOFEF PIDEF

bit 7 bit 0

Legend: U = Unimplemented bit, read as ‘0’

R = Readable bit K = Write ‘1’ to clear bit HS = Hardware Settable bit

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 BTSEF: Bit Stuff Error Flag bit

1 = Bit stuff error has been detected

0 = No bit stuff error has been detected

bit 6 BUSACCEF: Bus Access Error Flag bit

1 = Peripheral tried to access an unimplemented RAM location

0 = RAM location access was successful

bit 5 DMAEF: DMA Error Flag bit

1 = A USB DMA error condition is detected; the data size indicated by the buffer descriptor byte count

field is less than the number of received bytes, the received data is truncated

0 = No DMA error

bit 4 BTOEF: Bus Turnaround Time-out Error Flag bit

1 = Bus turnaround time-out has occurred

0 = No bus turnaround time-out has occurred

bit 3 DFN8EF: Data Field Size Error Flag bit

1 = Data field was not an integral number of bytes

0 = Data field was an integral number of bytes

bit 2 CRC16EF: CRC16 Failure Flag bit

1 = CRC16 failed

0 = CRC16 passed

bit 1 EOFEF: End-of-Frame (EOF) Error Flag bit

1 = End-of-Frame error has occurred

0 = End-of-Frame interrupt is disabled

bit 0 PIDEF: PID Check Failure Flag bit

1 = PID check failed

0 = PID check passed

 2009-2012 Microchip Technology Inc. DS70616G-page 405

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

BTSEE BUSACCEE DMAEE BTOEE DFN8EE CRC16EE CRC5EE PIDEE

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 BTSEE: Bit Stuff Error Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 6 BUSACCEE: Bus Access Error Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 5 DMAEE: DMA Error Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 4 BTOEE: Bus Turnaround Time-out Error Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 3 DFN8EE: Data Field Size Error Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 2 CRC16EE: CRC16 Failure Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 1 CRC5EE: CRC5 Host Error Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 0 PIDEE: PID Check Failure Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 406  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

BTSEE BUSACCEE DMAEE BTOEE DFN8EE CRC16EE EOFEE PIDEE

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 BTSEE: Bit Stuff Error Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 6 BUSACCEE: Bus Access Error Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 5 DMAEE: DMA Error Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 4 BTOEE: Bus Turnaround Time-out Error Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 3 DFN8EE: Data Field Size Error Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 2 CRC16EE: CRC16 Failure Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 1 EOFEE: End-of-Frame Error interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

bit 0 PIDEE: PID Check Failure Interrupt Enable bit

1 = Interrupt is enabled

0 = Interrupt is disabled

 2009-2012 Microchip Technology Inc. DS70616G-page 407

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

LSPD(1)RETRYDIS(1)— EPCONDIS EPRXEN EPTXEN EPSTALL EPHSHK

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7 LSPD: Low-Speed Direct Connection Enable bit (UEP0 only)(1)

1 = Direct connection to a low-speed device is enabled

0 = Direct connection to a low-speed device is disabled

bit 6 RETRYDIS: Retry Disable bit (UEP0 only)(1)

1 = Retry NAK transactions is disabled

0 = Retry NAK transactions is enabled; retry done in hardware

bit 5 Unimplemented: Read as ‘0’

bit 4 EPCONDIS: Bidirectional Endpoint Control bit

If EPTXEN and EPRXEN = 1:

1 = Disable Endpoint n from control transfers; only TX and RX transfers are allowed

0 = Enable Endpoint n for control (SETUP) transfers; TX and RX transfers are also allowed

For all other combinations of EPTXEN and EPRXEN:

This bit is ignored.

bit 3 EPRXEN: Endpoint Receive Enable bit

1 = Endpoint n receive is enabled

0 = Endpoint n receive is disabled

bit 2 EPTXEN: Endpoint Transmit Enable bit

1 = Endpoint n transmit is enabled

0 = Endpoint n transmit is disabled

bit 1 EPSTALL: Endpoint Stall Status bit

1 = Endpoint n was stalled

0 = Endpoint n was not stalled

bit 0 EPHSHK: Endpoint Handshake Enable bit

1 = Endpoint handshake is enabled

0 = Endpoint handshake is disabled (typically used for isochronous endpoints)

Note 1: These bits are available only for UxEP0 and only in Host mode. For all other UxEPn registers, these bits

are always unimplemented and read as ‘0’.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 408  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0

BDTPTRL<15:9> —

bit 7 bit 0

Legend:

R = Readable bit W =Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7-1 BDTPTRL<15:9>: Endpoint BDT Start Address bits

Defines bits 15-9 of the 32-bit endpoint buffer descriptor table start address.

bit 0 Unimplemented: Read as ‘0’

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

BDTPTRH<23:16>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7-0 BDTPTRH<23:16>: Endpoint BDT Start Address bits

Defines bits 23-16 of the 32-bit endpoint buffer descriptor table start address.

 2009-2012 Microchip Technology Inc. DS70616G-page 409

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

BDTPTRU<31:24>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7-0 BDTPTRU<31:24>: Endpoint BDT Start Address bits

Defines bits 31-24 of the 32-bit endpoint buffer descriptor table start address.

R/W-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0

PWMEN — — — — — PWMPOL CNTEN

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 PWMEN: PWM Enable bit

1 = PWM generator is enabled

0 = PWM generator is disabled; output is held in the Reset state specified by PWMPOL

bit 14-10

Unimplemented: Read as ‘0’

bit 9 PWMPOL: PWM Polarity bit

1 = PWM output is active-low and resets high

0 = PWM output is active-high and resets low

bit 8 CNTEN: PWM Counter Enable bit

1 = Counter is enabled

0 = Counter is disabled

bit 7-0 Unimplemented: Read as ‘0’

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 410  2009-2012 Microchip Technology Inc.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

DC<7:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PER<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 DC<7:0>: Duty Cycle bits

These bits select the PWM duty cycle.

bit 7-0 PER<7:0>: PWM Period bits

These bits select the PWM period.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — —

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 R-0 R-0 R-0

— — — — — FRM<10:8>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-3 Unimplemented: Read as ‘0’

bit 2-0 FRM<10:8>: 11-Bit Frame Number Upper 3 bits

These register bits are updated with the current frame number whenever a SOF token is received.

 2009-2012 Microchip Technology Inc. DS70616G-page 411

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — —

bit 15 bit 8

R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

FRM<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7-0 FRM<7:0>: 11-Bit Frame Number Lower 8 bits

These register bits are updated with the current frame number whenever a SOF token is received.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 412  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 413

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

23.0 10-BIT/12-BIT ANALOG-TO-

DIGITAL CONVERTER (ADC)

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices have two ADC

modules, ADC1 and ADC2. The ADC1 module

supports up to 32 analog input channels. The ADC2

module supports up to 16 analog input channels.

On ADC1, the AD12B bit (AD1CON1<10>) allows each

of the ADC modules to be configured by the user as

either a 10-bit, 4 Sample-and-Hold (S&H) ADC (default

configuration) or a 12-bit, 1 S&H ADC.

The ADC2 module only supports 10-bit operation with

4 S&H.

23.1 Key Features

The 10-bit ADC configuration has the following key

features:

• Successive Approximation (SAR) Conversion

• Conversion Speeds of up to 1.1 Msps

• Up to 32 Analog Input Pins

• External Voltage Reference Input Pins

• Simultaneous Sampling of up to Four Analog

Input Pins

• Automatic Channel Scan mode

• Selectable Conversion Trigger Source

• Selectable Buffer Fill modes

• Four Result Alignment Options (signed/unsigned,

fractional/integer)

• Operation during CPU Sleep and Idle modes

The 12-bit ADC configuration supports all the above

features, except:

• In the 12-bit configuration, conversion speeds of

up to 500 ksps are supported

• There is only one S&H amplifier in the 12-bit

configuration, so simultaneous sampling of

multiple channels is not supported.

Depending on the particular device pinout, the ADC

can have up to 32 analog input pins, designated AN0

through AN31. In addition, there are two analog input

pins for external voltage reference connections. These

voltage reference inputs can be shared with other ana-

log input pins. The actual number of analog input pins

and external voltage reference input configuration

depends on the specific device.

A block diagram of the ADC module is shown in

Figure 23-1. Figure 23-2 provides a diagram of the

ADC conversion clock period.

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this

data sheet, refer to Section 16. “Analog-

to-Digital Converter (ADC)” (DS70621)

of the “dsPIC33E/PIC24E Family Refer-

ence Manual”, which is available from the

Microchip web site (www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

Note: The ADC1 module needs to be disabled

before modifying the AD12B bit.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 414  2009-2012 Microchip Technology Inc.

FIGURE 23-1: ADCx MODULE BLOCK DIAGRAM

S&H0

S&H1

AN0

ANy(3)

AN1

VREFL

CH0SB<4:0>

CH0NA CH0NB

AN0

AN3

CH123SA

AN9

VREFL

CH123SB

CH123NA CH123NB

AN6

S&H2

AN1

AN4

CH123SA

AN10

VREFL

CH123SB

CH123NA CH123NB

AN7

S&H3

AN2

AN5

CH123SA

AN11

VREFL

CH123SB

CH123NA CH123NB

AN8

CH1(2)

CH0

CH2(2)

CH3(2)

CH0SA<4:0>

Channel

Scan

CSCNA

Alternate

Note 1: VREF+, VREF- inputs can be multiplexed

with other analog inputs.

2: Channels 1, 2 and 3 are not applicable

for the 12-bit mode of operation.

3: For dsPIC33EPXXX(GP/MC/MU)806 and

PIC24EPXXXGP806 devices, y = 0-15

and 24-31; for ADC2, y = 15; for all others,

y = 32.

4: When ADDMAEN (ADxCON4<8>) = 1,

enabling DMA, only ADCxBUF0 is used.

Input Selection

REF

(1)

REF

(1)

VCFG<2:0>

ADCxBUF0(4)

ADCxBUF1(4)

ADCxBUF2(4)

ADCxBUFF(4)

ADCxBUFE(4)

SAR ADC

VREFH VREFL

 2009-2012 Microchip Technology Inc. DS70616G-page 415

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 23-2: ADCx CONVERSION CLOCK PERIOD BLOCK DIAGRAM

ADCx Internal

RC Clock(1)

ADCx Conversion

Clock Multiplier

1, 2, 3, 4, 5,..., 64

ADxCON3<15>

TP(2)

TAD

ADxCON3<7:0>

Note 1: See the ADC electrical characteristics in Section 32.0 “Electrical Characteristics” for the exact RC clock value.

2: TP = 1/FP.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 416  2009-2012 Microchip Technology Inc.

23.2 ADC Helpful Tips

1. The SMPIx control bits in the ADxCON2 registers:

a) Determine when the ADC interrupt flag is set

and an interrupt is generated, if enabled.

b) When the CSCNA bit in the ADxCON2 reg-

ister is set to ‘1’, this determines when the

ADC analog scan channel list, defined in

the AD1CSSL/AD1CSSH registers, starts

over from the beginning.

c) When the DMA peripheral is not used

(ADDMAEN = 0), this determines when the

ADC Result Buffer Pointer to ADC1BUF0-

ADC1BUFF gets reset back to the

beginning at ADC1BUF0.

d) When the DMA peripheral is used

(ADDMAEN = 1), this determines when the

DMA Address Pointer is incremented after a

sample/conversion operation. ADC1BUF0 is

the only ADC buffer used in this mode. The

ADC Result Buffer Pointer to ADC1BUF0-

ADC1BUFF gets reset back to the beginning

at ADC1BUF0. The DMA address is incre-

mented after completion of every 32nd

sample/conversion operation. Conversion

results are stored in the ADC1BUF0 register

for transfer to RAM using DMA.

2. When the DMA module is disabled

(ADDMAEN = 0), the ADC has 16 result buffers.

ADC conversion results are stored sequentially

in ADC1BUF0-ADC1BUFF, regardless of which

analog inputs are being used subject to the

SMPIx bits and the condition described in 1c)

above. There is no relationship between the

ANx input being measured and which ADC

buffer (ADC1BUF0-ADC1BUFF) that the

conversion results will be placed in.

3. When the DMA module is disabled

(ADDMAEN = 1), the ADC module has only

1 ADC result buffer (i.e., ADC1BUF0) per ADC

peripheral and the ADC conversion result must

be read, either by the CPU or DMA controller,

before the next ADC conversion is complete to

avoid overwriting the previous value.

4. The DONE bit (ADxCON1<0>) is only cleared at

the start of each conversion and is set at the

completion of the conversion, but remains set

indefinitely, even through the next sample phase

until the next conversion begins. If application

code is monitoring the DONE bit in any kind of

software loop, the user must consider this

behavior because the CPU code execution is

faster than the ADC. As a result, in Manual

Sample mode, particularly where the user’s

code is setting the SAMP bit (ADxCON1<1>),

the DONE bit should also be cleared by the user

application just before setting the SAMP bit.

23.3 ADC Resources

Many useful resources related to Analog-to-Digital

conversion are provided on the main product page of

the Microchip web site for the devices listed in this data

sheet. This product page, which can be accessed using

this link, contains the latest updates and additional

information.

23.3.1 KEY RESOURCES

•Section 16. “Analog-to-Digital Converter

(ADC)” (DS70621) in the “dsPIC33E/PIC24E

Family Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

 2009-2012 Microchip Technology Inc. DS70616G-page 417

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

23.4 ADC Control Registers

R/W-0 U-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0

ADON —ADSIDLADDMABM—AD12B

(1)FORM<1:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0, HSC R/C-0, HSC

SSRC<2:0> SSRCG SIMSAM ASAM(3)SAMP DONE(3)

bit 7 bit 0

Legend: C = Clearable bit HSC = Hardware Settable/Clearable bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 ADON: ADC Operating Mode bit

1 = ADC module is operating

0 = ADC is off

bit 14 Unimplemented: Read as ‘0’

bit 13 ADSIDL: ADC Stop in Idle Mode bit

1 = Discontinues module operation when device enters Idle mode

0 = Continues module operation in Idle mode

bit 12 ADDMABM: DMA Buffer Build Mode bit

1 = DMA buffers are written in the order of conversion; the module provides an address to the DMA

channel that is the same as the address used for the non-DMA stand-alone buffer

0 = DMA buffers are written in Scatter/Gather mode; the module provides a Scatter/Gather address

to the DMA channel, based on the index of the analog input and the size of the DMA buffer

bit 11 Unimplemented: Read as ‘0’

bit 10 AD12B: ADC 10-Bit or 12-Bit Operation Mode bit(1)

1 = 12-bit, 1-channel ADC operation

0 = 10-bit, 4-channel ADC operation

bit 9-8 FORM<1:0>: Data Output Format bits

For 10-Bit Operation:

11 = Signed fractional (DOUT = sddd dddd dd00 0000, where s = .NOT.d<9>)

10 = Fractional (DOUT = dddd dddd dd00 0000)

01 = Signed integer (DOUT = ssss sssd dddd dddd, where s = .NOT.d<9>)

00 = Integer (DOUT = 0000 00dd dddd dddd)

For 12-Bit Operation:

11 = Signed fractional (DOUT = sddd dddd dddd 0000, where s = .NOT.d<11>)

10 = Fractional (DOUT = dddd dddd dddd 0000)

01 = Signed Integer (DOUT = ssss sddd dddd dddd, where s = .NOT.d<11>)

00 = Integer (DOUT = 0000 dddd dddd dddd)

Note 1: This bit is only available in the ADC1 module. In the ADC2 module, this bit is unimplemented and is read

as ‘0’.

2: This setting is available in dsPIC33EPXXX(MC/MU)806/810/814 devices only.

3: Do not clear the DONE bit in software if ADC Sample Auto-Start is enabled (ASAM = 1).

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 418  2009-2012 Microchip Technology Inc.

bit 7-5 SSRC<2:0>: Sample Clock Source Select bits

If SSRCG = 1:

111 = Reserved

110 = PWM Generator 7 primary trigger compare ends sampling and starts conversion(2)

101 = PWM Generator 6 primary trigger compare ends sampling and starts conversion(2)

100 = PWM Generator 5 primary trigger compare ends sampling and starts conversion(2)

011 = PWM Generator 4 primary trigger compare ends sampling and starts conversion(2)

010 = PWM Generator 3 primary trigger compare ends sampling and starts conversion(2)

001 = PWM Generator 2 primary trigger compare ends sampling and starts conversion(2)

000 = PWM Generator 1 primary trigger compare ends sampling and starts conversion(2)

If SSRCG = 0:

111 = Internal counter ends sampling and starts conversion (auto-convert)

110 = Reserved

101 = PWM secondary Special Event Trigger ends sampling and starts conversion(2)

100 = Timer5 compare ends sampling and starts conversion

011 = PWM primary Special Event Trigger ends sampling and starts conversion(2)

010 = Timer3 compare ends sampling and starts conversion

001 = Active transition on the INT0 pin ends sampling and starts conversion

000 = Clearing the Sample bit (SAMP) ends sampling and starts conversion (Manual mode)

bit 4 SSRCG: Sample Clock Source Group bit

(See bits<7-5> for details.)

bit 3 SIMSAM: Simultaneous Sample Select bit (only applicable when CHPS<1:0> = 01 or 1x)

When AD12B = 1, SIMSAM is: U-0, Unimplemented, Read as ‘0’

1 = Samples CH0, CH1, CH2, CH3 simultaneously (when CHPS<1:0> = 1x); or samples CH0 and

CH1 simultaneously (when CHPS<1:0> = 01)

0 = Samples multiple channels individually in sequence

bit 2 ASAM: ADC Sample Auto-Start bit(3)

1 = Sampling begins immediately after the last conversion; SAMP bit is auto-set

0 = Sampling begins when the SAMP bit is set

bit 1 SAMP: ADC Sample Enable bit

1 = ADC S&H amplifiers are sampling

0 = ADC S&H amplifiers are holding

If ASAM = 0, software can write ‘1’ to begin sampling. Automatically set by hardware if ASAM = 1.

If SSRC = 000, software can write ‘0’ to end sampling and start conversion. If SSRC 000, automatically

cleared by hardware to end sampling and start conversion.

bit 0 DONE: ADC Conversion Status bit(3)

1 = ADC conversion cycle is completed.

0 = ADC conversion has not started or is in progress

Automatically set by hardware when ADC conversion is complete. Software can write ‘0’ to clear the

DONE status (software not allowed to write ‘1’). Clearing this bit does NOT affect any operation in

progress. Automatically cleared by hardware at the start of a new conversion.

Note 1: This bit is only available in the ADC1 module. In the ADC2 module, this bit is unimplemented and is read

as ‘0’.

2: This setting is available in dsPIC33EPXXX(MC/MU)806/810/814 devices only.

3: Do not clear the DONE bit in software if ADC Sample Auto-Start is enabled (ASAM = 1).

 2009-2012 Microchip Technology Inc. DS70616G-page 419

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0

VCFG<2:0> —— CSCNA CHPS<1:0>

bit 15 bit 8

R-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

BUFS SMPI<4:0> BUFM ALTS

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-13 VCFG<2:0>: Converter Voltage Reference Configuration bits

bit 12-11 Unimplemented: Read as ‘0’

bit 10 CSCNA: Input Scan Select bit

1 = Scans inputs for CH0+ during Sample A bit

0 = Does not scan inputs

bit 9-8 CHPS<1:0>: Channel Select bits

When AD12B = 1, CHPS<1:0> is: U-0, Unimplemented, Read as ‘0’:

1x = Converts CH0, CH1, CH2 and CH3

01 = Converts CH0 and CH1

00 = Converts CH0

bit 7 BUFS: Buffer Fill Status bit (only valid when BUFM = 1)

1 = ADC is currently filling the second half of the buffer; the user application should access data in the

first half of the buffer

0 = ADC is currently filling the first half of the buffer; the user application should access data in the

second half of the buffer

bit 6-2 SMPI<4:0>: Increment Rate bits

When ADDMAEN = 0:

01111 = Generates interrupt after completion of every 16th sample/conversion operation

01110 = Generates interrupt after completion of every 15th sample/conversion operation

•

00001 = Generates interrupt after completion of every 2nd sample/conversion operation

00000 = Generates interrupt after completion of every sample/conversion operation

When ADDMAEN = 1:

11111 = Increments the DMA address after completion of every 32nd sample/conversion operation

11110 = Increments the DMA address after completion of every 31st sample/conversion operation

•

00001 = Increments the DMA address after completion of every 2nd sample/conversion operation

00000 = Increments the DMA address after completion of every sample/conversion operation

VREFH VREFL

000 AVDD Avss

001 External VREF+ Avss

010 AVDD External VREF-

011 External VREF+ External VREF-

1xx AVDD Avss

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 420  2009-2012 Microchip Technology Inc.

bit 1 BUFM: Buffer Fill Mode Select bit

1 = Starts filling the first half of the buffer on the first interrupt and the second half of the buffer on the

next interrupt

0 = Always starts filling the buffer from the Start address.

bit 0 ALTS: Alternate Input Sample Mode Select bit

1 = Uses channel input selects for Sample A on the first sample and Sample B on the next sample

0 = Always uses channel input selects for Sample A

 2009-2012 Microchip Technology Inc. DS70616G-page 421

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0

VCFG<2:0> —— CSCNA CHPS<1:0>

bit 15 bit 8

R-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

BUFS — SMPI<3:0> BUFM ALTS

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-13 VCFG<2:0>: Converter Voltage Reference Configuration bits

bit 12-11 Unimplemented: Read as ‘0’

bit 10 CSCNA: Input Scan Select bit

1 = Scans inputs for CH0+ during Sample A bit

0 = Does not scan inputs

bit 9-8 CHPS<1:0>: Channel Select bits

When AD12B = 1, CHPS<1:0> is: U-0, Unimplemented, Read as ‘0’:

1x = Converts CH0, CH1, CH2 and CH3

01 = Converts CH0 and CH1

00 = Converts CH0

bit 7 BUFS: Buffer Fill Status bit (only valid when BUFM = 1)

1 = ADC is currently filling the second half of the buffer; the user application should access data in the

first half of the buffer

0 = ADC is currently filling the first half of the buffer; the user application should access data in the

second half of the buffer

bit 6-2 SMPI<3:0>: Increment Rate bits

When ADDMAEN = 0:

1111 = Generates interrupt after completion of every 16th sample/conversion operation

1110 = Generates interrupt after completion of every 15th sample/conversion operation

•

0001 = Generates interrupt after completion of every 2nd sample/conversion operation

0000 = Generates interrupt after completion of every sample/conversion operation

When ADDMAEN = 1:

1111 = Increments the DMA address after completion of every 16th sample/conversion operation

1110 = Increments the DMA address after completion of every 15th sample/conversion operation

•

0001 = Increments the DMA address after completion of every 2nd sample/conversion operation

0000 = Increments the DMA address after completion of every sample/conversion operation

VREFH VREFL

000 AVDD Avss

001 External VREF+ Avss

010 AVDD External VREF-

011 External VREF+ External VREF-

1xx AVDD Avss

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 422  2009-2012 Microchip Technology Inc.

bit 1 BUFM: Buffer Fill Mode Select bit

1 = Starts buffer filling the first half of the buffer on the first interrupt and the second half of the buffer

on the next interrupt

0 = Always starts filling the buffer from the Start address

bit 0 ALTS: Alternate Input Sample Mode Select bit

1 = Uses channel input selects for Sample A on first sample and Sample B on next sample

0 = Always uses channel input selects for Sample A

 2009-2012 Microchip Technology Inc. DS70616G-page 423

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

ADRC —— SAMC<4:0>(1)

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

ADCS<7:0>(2,3)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 ADRC: ADC Conversion Clock Source bit

1 = ADC internal RC clock

0 = Clock Derived From System Clock

bit 14-13 Unimplemented: Read as ‘0’

bit 12-8 SAMC<4:0>: Auto-Sample Time bits(1)

11111 = 31 TAD

•

00001 = 1 TAD

00000 = 0 TAD

bit 7-0 ADCS<7:0>: ADC Conversion Clock Select bits(2,3)

11111111 = TP • (ADCS<7:0> + 1) = 256 • TCY = TAD

•

00000010 = TP • (ADCS<7:0> + 1) = 3 • TCY = TAD

00000001 = TP • (ADCS<7:0> + 1) = 2 • TCY = TAD

00000000 = TP • (ADCS<7:0> + 1) = 1 • TCY = TAD

Note 1: This bit is only used if ADxCON1<7:5> (SSRC<2:0>) = 111 and ADxCON1<4> (SSRCG) = 0.

2: This bit is not used if ADxCON3<15> (ADRC) = 1.

3: TP = 1/FP.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 424  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0

— — — — — — — ADDMAEN

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0

— — — — — DMABL<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-9 Unimplemented: Read as ‘0’

bit 8 ADDMAEN: ADC DMA Enable bit

1 = Conversion results are stored in ADCxBUF0 register for transferring to RAM using DMA

0 = Conversion results are stored in ADCxBUF0 through ADCxBUFF registers; DMA will not be used

bit 7-3 Unimplemented: Read as ‘0’

bit 2-0 DMABL<2:0>: Selects Number of DMA Buffer Locations per Analog Input bits

111 = Allocates 128 words of buffer to each analog input

110 = Allocates 64 words of buffer to each analog input

101 = Allocates 32 words of buffer to each analog input

100 = Allocates 16 words of buffer to each analog input

011 = Allocates 8 words of buffer to each analog input

010 = Allocates 4 words of buffer to each analog input

001 = Allocates 2 words of buffer to each analog input

000 = Allocates 1 word of buffer to each analog input

 2009-2012 Microchip Technology Inc. DS70616G-page 425

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0

— — — — — CH123NB<1:0> CH123SB

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0

— — — — — CH123NA<1:0> CH123SA

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-11 Unimplemented: Read as ‘0’

bit 10-9 CH123NB<1:0>: Channel 1, 2, 3 Negative Input Select for Sample B bits

When AD12B = 1, CHxNB is: U-0, Unimplemented, Read as ‘0’:

11 = CH1 negative input is AN9, CH2 negative input is AN10, CH3 negative input is AN11

10 = CH1 negative input is AN6, CH2 negative input is AN7, CH3 negative input is AN8

0x = CH1, CH2, CH3 negative input is VREFL

bit 8 CH123SB: Channel 1, 2, 3 Positive Input Select for Sample B bit

When AD12B = 1, CHxSA is: U-0, Unimplemented, Read as ‘0’:

1 = CH1 positive input is AN3, CH2 positive input is AN4, CH3 positive input is AN5

0 = CH1 positive input is AN0, CH2 positive input is AN1, CH3 positive input is AN2

bit 7-3 Unimplemented: Read as ‘0’

bit 2-1 CH123NA<1:0>: Channel 1, 2, 3 Negative Input Select for Sample A bits

When AD12B = 1, CHxNA is: U-0, Unimplemented, Read as ‘0’:

11 = CH1 negative input is AN9, CH2 negative input is AN10, CH3 negative input is AN11

10 = CH1 negative input is AN6, CH2 negative input is AN7, CH3 negative input is AN8

0x = CH1, CH2, CH3 negative input is VREFL

bit 0 CH123SA: Channel 1, 2, 3 Positive Input Select for Sample A bit

When AD12B = 1, CHxSA is: U-0, Unimplemented, Read as ‘0’:

1 = CH1 positive input is AN3, CH2 positive input is AN4, CH3 positive input is AN5

0 = CH1 positive input is AN0, CH2 positive input is AN1, CH3 positive input is AN2

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 426  2009-2012 Microchip Technology Inc.

R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

CH0NB —— CH0SB<4:0>(1)

bit 15 bit 8

R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

CH0NA —— CH0SA<4:0>(1)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 CH0NB: Channel 0 Negative Input Select for Sample B bit

Same definition as bit 7.

bit 14-13 Unimplemented: Read as ‘0’

bit 12-8 CH0SB<4:0>: Channel 0 Positive Input Select for Sample B bits(1)

Same definition as bits<4:0>.

bit 7 CH0NA: Channel 0 Negative Input Select for Sample A bit

1 = Channel 0 negative input is AN1

0 = Channel 0 negative input is VREFL

bit 6-5 Unimplemented: Read as ‘0’

bit 4-0 CH0SA<4:0>: Channel 0 Positive Input Select for Sample A bits(1)

11111 = Channel 0 positive input is AN31

11110 = Channel 0 positive input is AN30

•

00010 = Channel 0 positive input is AN2

00001 = Channel 0 positive input is AN1

00000 = Channel 0 positive input is AN0

Note 1: The AN16 through AN31 pins are not available for the ADC2 module. The AN16 through AN23 pins are

not available for dsPIC33EP256MU806 (64-pin) devices.

 2009-2012 Microchip Technology Inc. DS70616G-page 427

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

CSS31 CSS30 CSS29 CSS28 CSS27 CSS26 CSS25 CSS24

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

CSS23 CSS22 CSS21 CSS20 CSS19 CSS18 CSS17 CSS16

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 CSS<31:16>: ADC1 Input Scan Selection bits

1 = Selects ANx for input scan

0 = Skips ANx for input scan

Note 1: On devices with less than 32 analog inputs, all ADxCSSH bits can be selected by user software. However,

inputs selected for scan without a corresponding input on the device converts to VREFL.

2: CSSx = ANx, where x = 16-31.

3: ADC2 only supports analog inputs, AN0-AN15; therefore, no ADC2 Input Scan Select register exists.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

CSS15 CSS14 CSS13 CSS12 CSS11 CSS10 CSS9 CSS8

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

CSS7 CSS6 CSS5 CSS4 CSS3 CSS2 CSS1 CSS0

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 CSS<15:0>: ADC Input Scan Selection bits

1 = Selects ANx for input scan

0 = Skips ANx for input scan

Note 1: On devices with less than 16 analog inputs, all ADxCSSL bits can be selected by the user. However,

inputs selected for scan without a corresponding input on the device converts to VREFL.

2: CSSx = ANx, where x = 0-15.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 428  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 429

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

24.0 DATA CONVERTER

INTERFACE (DCI) MODULE

24.1 Module Introduction

The Data Converter Interface (DCI) module allows

simple interfacing of devices, such as audio coder/

decoders (Codecs), ADC and D/A Converters. The

following interfaces are supported:

• Framed Synchronous Serial Transfer (Single or

Multi-Channel)

• Inter-IC Sound (I2S) Interface

• AC-Link Compliant mode

General features include:

• Programmable word size up to 16 bits

• Supports up to 16 time slots, for a maximum

frame size of 256 bits

• Data buffering for up to 4 samples without CPU

overhead

FIGURE 24-1: DCI MODULE BLOCK DIAGRAM

Note 1: This data sheet is not intended to be a

comprehensive reference source. To

complement the information in this data

sheet, refer to “Section 20. Data

Converter Interface (DCI)” (DS70356)

of the “dsPIC33E/PIC24E Family

Reference Manual”, which is available

from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

BCG Control Bits

16-Bit Data Bus

Sample Rate

Generator

SCKD

FSD

DCI Buffer

Frame

Synchronization

Generator

Control Unit

DCI Shift Register

Receive Buffer

Registers w/Shadow

Word Size Selection bits

Frame Length Selection bits

DCI Mode Selection bits

CSCK

COFS

CSDI

CSDO

15 0

Transmit Buffer

Registers w/Shadow

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 430  2009-2012 Microchip Technology Inc.

24.2 DCI Resources

Many useful resources related to DCI are provided on

the main product page of the Microchip web site for the

devices listed in this data sheet. This product page,

which can be accessed using this link, contains the

latest updates and additional information.

24.2.1 KEY RESOURCES

•Section 20. “Data Converter Interface (DCI)”

(DS70356) in the “dsPIC33E/PIC24E Family

Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

 2009-2012 Microchip Technology Inc. DS70616G-page 431

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

24.3 DCI Control Registers

R/W-0 U-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0

DCIEN rDCISIDLr DLOOP CSCKD CSCKE COFSD

bit 15 bit 8

R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 R/W-0 R/W-0

UNFM CSDOM DJST r r rCOFSM<1:0>

bit 7 bit 0

Legend: r = Reserved bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 DCIEN: DCI Module Enable bit

1 = Module is enabled

0 = Module is disabled

bit 14 Reserved: Read as ‘0’

bit 13 DCISIDL: DCI Stop in Idle Control bit

1 = Module will halt in CPU Idle mode

0 = Module will continue to operate in CPU Idle mode

bit 12 Reserved: Read as ‘0’

bit 11 DLOOP: Digital Loopback Mode Control bit

1 = Digital Loopback mode is enabled; CSDI and CSDO pins are internally connected

0 = Digital Loopback mode is disabled

bit 10 CSCKD: Sample Clock Direction Control bit

1 = CSCK pin is an input when DCI module is enabled

0 = CSCK pin is an output when DCI module is enabled

bit 9 CSCKE: Sample Clock Edge Control bit

1 = Data changes on serial clock falling edge, sampled on serial clock rising edge

0 = Data changes on serial clock rising edge, sampled on serial clock falling edge

bit 8 COFSD: Frame Synchronization Direction Control bit

1 = COFS pin is an input when DCI module is enabled

0 = COFS pin is an output when DCI module is enabled

bit 7 UNFM: Underflow Mode bit

1 = Transmits last value written to the Transmit registers on a transmit underflow

0 = Transmits ‘0’s on a transmit underflow

bit 6 CSDOM: Serial Data Output Mode bit

1 = CSDO pin will be tri-stated during disabled transmit time slots

0 = CSDO pin drives ‘0’s during disabled transmit time slots

bit 5 DJST: DCI Data Justification Control bit

1 = Data transmission/reception begins during the same serial clock cycle as the frame synchronization

pulse

0 = Data transmission/reception begins one serial clock cycle after the frame synchronization pulse

bit 4-2 Reserved: Read as ‘0’

bit 1-0 COFSM<1:0>: Frame Sync Mode bits

11 = 20-Bit AC-Link mode

10 = 16-Bit AC-Link mode

01 = I2S Frame Sync mode

00 = Multi-Channel Frame Sync mode

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 432  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 R/W-0 R/W-0 U-0 R/W-0

r r r r BLEN<1:0> rCOFSG3

bit 15 bit 8

R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0

COFSG<2:0> r WS<3:0>

bit 7 bit 0

Legend: r = Reserved bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 Reserved: Read as ‘0’

bit 11-10 BLEN<1:0>: Buffer Length Control bits

11 = Four data words will be buffered between interrupts

10 = Three data words will be buffered between interrupts

01 = Two data words will be buffered between interrupts

00 = One data word will be buffered between interrupts

bit 9 Reserved: Read as ‘0’

bit 8-5 COFSG<3:0>: Frame Sync Generator Control bits

1111 = Data frame has 16 words

•

0010 = Data frame has 3 words

0001 = Data frame has 2 words

0000 = Data frame has 1 word

bit 4 Reserved: Read as ‘0’

bit 3-0 WS<3:0>: DCI Data Word Size bits

1111 = Data word size is 16 bits

•

0100 = Data word size is 5 bits

0011 = Data word size is 4 bits

0010 = Invalid Selection. Do not use. Unexpected results may occur.

0001 = Invalid Selection. Do not use. Unexpected results may occur.

0000 = Invalid Selection. Do not use. Unexpected results may occur.

 2009-2012 Microchip Technology Inc. DS70616G-page 433

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0

r r r rBCG<11:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

BCG<7:0>

bit 7 bit 0

Legend: r = Reserved bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 Reserved: Read as ‘0’

bit 11-0 BCG<11:0>: DCI Clock Generator Control bits

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 434  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 R-0 R-0 R-0 R-0

r r r r SLOT<3:0>

bit 15 bit 8

U-0 U-0 U-0 U-0 R-0 R-0 R-0 R-0

r r r r ROV RFUL TUNF TMPTY

bit 7 bit 0

Legend: r = Reserved bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 Reserved: Read as ‘0’

bit 11-8 SLOT<3:0>: DCI Slot Status bits

1111 = Slot 15 is currently active

•

0010 = Slot 2 is currently active

0001 = Slot 1 is currently active

0000 = Slot 0 is currently active

bit 7-4 Reserved: Read as ‘0’

bit 3 ROV: Receive Overflow Status bit

1 = A receive overflow has occurred for at least one Receive register

0 = A receive overflow has not occurred

bit 2 RFUL: Receive Buffer Full Status bit

1 = New data is available in the Receive registers

0 = The Receive registers have old data

bit 1 TUNF: Transmit Buffer Underflow Status bit

1 = A transmit underflow has occurred for at least one Transmit register

0 = A transmit underflow has not occurred

bit 0 TMPTY: Transmit Buffer Empty Status bit

1 = The Transmit registers are empty

0 = The Transmit registers are not empty

 2009-2012 Microchip Technology Inc. DS70616G-page 435

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

RSE15 RSE14 RSE13 RSE12 RSE11 RSE10 RSE9 RSE8

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

RSE7 RSE6 RSE5 RSE4 RSE3 RSE2 RSE1 RSE0

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 RSE<15:0>: Receive Slot Enable bits

1 = CSDI data is received during the individual time slot n

0 = CSDI data is ignored during the individual time slot n

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

TSE15 TSE14 TSE13 TSE12 TSE11 TSE10 TSE9 TSE8

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

TSE7 TSE6 TSE5 TSE4 TSE3 TSE2 TSE1 TSE0

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 TSE<15:0>: Transmit Slot Enable Control bits

1 = Transmit buffer contents are sent during the individual time slot n

0 = CSDO pin is tri-stated or driven to logic ‘0’ during the individual time slot, depending on the state

of the CSDOM bit

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 436  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 437

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

25.0 COMPARATOR MODULE The comparator module provides three comparators

that can be configured in different ways. As shown in

Figure 25-1, individual comparator options are

specified by the comparator module’s Special Function

These options allow users to:

• Select the edge for trigger and interrupt generation

• Configure the comparator voltage reference and

band gap

• Configure output blanking and masking

The comparator operating mode is determined by the

input selections (i.e., whether the input voltage is

compared to a second input voltage or to an internal

voltage reference).

FIGURE 25-1: COMPARATOR I/O OPERATING MODES

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this data

sheet, refer to Section 26. “Op Amp/

Comparator” (DS70357) of the

“dsPIC33E/PIC24E Family Reference

Manual”, which is available from the

Microchip web site (www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

IVREF

Comparator Voltage

CMPx(1)

Blanking

Function

Digital

Filter

Output Data/Control

CxOUT

(1)

Reference

CxIN2-(1)

CxIN1-(1)

CxIN3-(1)

(see Figure 25-2)CVREF

(see Figure 25-3)(see Figure 25-4)

–

VIN+

VIN-

BGSEL<1:0>

REF

-AV

2.20V

0.20V

0.60V

Note 1: An ‘x’ is a pin, bit or register name and denotes Comparator 1, 2 or 3.

VREF+

CREF

CxIN1+(1)

CVREFIN

CCH<1:0>

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 438  2009-2012 Microchip Technology Inc.

FIGURE 25-2: COMPARATOR VOLTAGE REFERENCE BLOCK DIAGRAM

FIGURE 25-3: USER-PROGRAMMABLE BLANKING FUNCTION BLOCK DIAGRAM

16-to-1 MUX

CVREN

CVRSS = 0

AVDD

VREF+CVRSS = 1

CVRSS = 0

VREF–CVRSS = 1

16 Steps

CVRR

CVREF

CVR3

CVR2

CVR1

CVR0

CVRCON<3:0>

AVSS

CVRSRC

CVRCON<CVROE>

CVREFIN

VREFSEL

SELSRCA<3:0>

SELSRCB<3:0>

SELSRCC<3:0>

AND

CMxMSKCON

MUX A

MAI

MBI

MCI

Comparator Output To Di g ita l

Signals

Filter

Blanking

Signals

ANDI

MASK

“AND-OR” Function

HLMS

MUX BMUX C

Blanking

Logic

(CMxMSKCON<15)

(CMxMSKSRC<11:8)

(CMxMSKSRC<7:4)

(CMxMSKSRC<3:0>)

MBI

MCI

MAI

MBI

MCI

MAI

 2009-2012 Microchip Technology Inc. DS70616G-page 439

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 25-4: DIGITAL FILTER INTERCONNECT BLOCK DIAGRAM

25.1 Comparator Resources

Many useful resources related to the Comparator are

provided on the main product page of the Microchip

web site for the devices listed in this data sheet. This

product page, which can be accessed using this link,

contains the latest updates and additional information.

25.1.1 KEY RESOURCES

•Section 26. “Op Amp/Comparator” (DS70357)

in the “dsPIC33E/PIC24E Family Reference

Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

CXOUT

CFLTREN

Digital Filter

TxCLK(1,2)

SYNCOx(3)

FP(4)

FOSC(4)

CFSEL<2:0>

CFDIV

Note 1: See the Type C Timer Block Diagram (Figure 13-2).

2: See the Type B Timer Block Diagram (Figure 13-1).

3: See the PWM Module Register Interconnect Diagram (Figure 16-2).

4: See the Oscillator System Diagram (Figure 9-1).

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 440  2009-2012 Microchip Technology Inc.

25.2 Comparator Control Registers

R/W-0 U-0 U-0 U-0 U-0 R-0 R-0 R-0

CMSIDL — — — — C3EVT C2EVT C1EVT

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 R-0 R-0 R-0

— — — — — C3OUT C2OUT C1OUT

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 CMSIDL: Comparator Stop in Idle Mode bit

1 = Discontinues operation of all comparators when device enters Idle mode

0 = Continues operation of all comparators in Idle mode

bit 14-11 Unimplemented: Read as ‘0’

bit 10 C3EVT: Comparator 3 Event Status bit

1 = Comparator event occurred

0 = Comparator event did not occur

bit 9 C2EVT: Comparator 2 Event Status bit

1 = Comparator event occurred

0 = Comparator event did not occur

bit 8 C1EVT: Comparator 1 Event Status bit

1 = Comparator event occurred

0 = Comparator event did not occur

bit 7-3 Unimplemented: Read as ‘0’

bit 2 C3OUT: Comparator 3 Output Status bit

When CPOL = 0:

1 = VIN+ > VIN-

0 = VIN+ < VIN-

When CPOL = 1:

1 = VIN+ < VIN-

0 = VIN+ > VIN-

bit 1 C2OUT: Comparator 2 Output Status bit

When CPOL = 0:

1 = VIN+ > VIN-

0 = VIN+ < VIN-

When CPOL = 1:

1 = VIN+ < VIN-

0 = VIN+ > VIN-

bit 0 C1OUT: Comparator 1 Output Status bit

When CPOL = 0:

1 = VIN+ > VIN-

0 = VIN+ < VIN-

When CPOL = 1:

1 = VIN+ < VIN-

0 = VIN+ > VIN-

 2009-2012 Microchip Technology Inc. DS70616G-page 441

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 R/W-0 R/W-0

CON COE CPOL — — — CEVT COUT

bit 15 bit 8

R/W-0 R/W-0 U-0 R/W-0 U-0 U-0 R/W-0 R/W-0

EVPOL<1:0> —CREF—— CCH<1:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 CON: Comparator Enable bit

1 = Comparator is enabled

0 = Comparator is disabled

bit 14 COE: Comparator Output Enable bit

1 = Comparator output is present on the CxOUT pin

0 = Comparator output is internal only

bit 13 CPOL: Comparator Output Polarity Select bit

1 = Comparator output is inverted

0 = Comparator output is not inverted

bit 12-10 Unimplemented: Read as ‘0’

bit 9 CEVT: Comparator Event bit

1 = Comparator event according to EVPOL<1:0> settings occurred; disables future triggers and

interrupts until the bit is cleared

0 = Comparator event did not occur

bit 8 COUT: Comparator Output bit

When CPOL = 0 (non-inverted polarity):

1 = VIN+ > VIN-

0 = VIN+ < VIN-

When CPOL = 1 (inverted polarity):

1 = VIN+ < VIN-

0 = VIN+ > VIN-

bit 7-6 EVPOL<1:0>: Trigger/Event/Interrupt Polarity Select bits

11 = Trigger/Event/Interrupt generated on any change of the comparator output (while CEVT = 0)

10 = Trigger/Event/Interrupt generated only on high-to-low transition of the polarity selected comparator

output (while CEVT = 0)

If CPOL = 1 (inverted polarity):

Low-to-high transition of the comparator output.

If CPOL = 0 (non-inverted polarity):

High-to-low transition of the comparator output.

01 = Trigger/Event/Interrupt generated only on low-to-high transition of the polarity selected comparator

output (while CEVT = 0)

If CPOL = 1 (inverted polarity):

High-to-low transition of the comparator output.

If CPOL = 0 (non-inverted polarity):

Low-to-high transition of the comparator output.

00 = Trigger/Event/Interrupt generation is disabled

bit 5 Unimplemented: Read as ‘0’

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 442  2009-2012 Microchip Technology Inc.

bit 4 CREF: Comparator Reference Select bit (VIN+ input)

1 = VIN+ input connects to internal CVREFIN voltage

0 = VIN+ input connects to CxIN1+ pin

bit 3-2 Unimplemented: Read as ‘0’

bit 1-0 CCH<1:0>: Comparator Channel Select bits

11 =VIN- input of comparator connects to IVREF

10 =VIN- input of comparator connects to CXIN3- pin

01 =V

IN- input of comparator connects to CXIN1- pin

00 =VIN- input of comparator connects to CXIN2- pin

 2009-2012 Microchip Technology Inc. DS70616G-page 443

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

CONTROL REGISTER

U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 RW-0

— — — — SELSRCC<3:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SELSRCB<3:0> SELSRCA<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 Unimplemented: Read as ‘0’

bit 11-8 SELSRCC<3:0>: Mask C Input Select bits

1111 = FLT4

1110 = FLT2

1101 = PWM7H

1100 = PWM7L

1011 = PWM6H

1010 = PWM6L

1001 = PWM5H

1000 = PWM5L

0111 = PWM4H

0110 = PWM4L

0101 = PWM3H

0100 = PWM3L

0011 = PWM2H

0010 = PWM2L

0001 = PWM1H

0000 = PWM1L

bit 7-4 SELSRCB<3:0>: Mask B Input Select bits

1111 = FLT4

1110 = FLT2

1101 = PWM7H

1100 = PWM7L

1011 = PWM6H

1010 = PWM6L

1001 = PWM5H

1000 = PWM5L

0111 = PWM4H

0110 = PWM4L

0101 = PWM3H

0100 = PWM3L

0011 = PWM2H

0010 = PWM2L

0001 = PWM1H

0000 = PWM1L

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 444  2009-2012 Microchip Technology Inc.

bit 3-0 SELSRCA<3:0>: Mask A Input Select bits

1111 = FLT4

1110 = FLT2

1101 = PWM7H

1100 = PWM7L

1011 = PWM6H

1010 = PWM6L

1001 = PWM5H

1000 = PWM5L

0111 = PWM4H

0110 = PWM4L

0101 = PWM3H

0100 = PWM3L

0011 = PWM2H

0010 = PWM2L

0001 = PWM1H

0000 = PWM1L

CONTROL REGISTER (CONTINUED)

 2009-2012 Microchip Technology Inc. DS70616G-page 445

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

CONTROL REGISTER

R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

HLMS — OCEN OCNEN OBEN OBNEN OAEN OANEN

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

NAGS PAGS ACEN ACNEN ABEN ABNEN AAEN AANEN

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 HLMS: High or Low-Level Masking Select bits

1 = The masking (blanking) function will prevent any asserted (‘0’) comparator signal from propagating

0 = The masking (blanking) function will prevent any asserted (‘1’) comparator signal from propagating

bit 14 Unimplemented: Read as '0'

bit 13 OCEN: OR Gate C Input Enable bit

1 = MCI is connected to OR gate

0 = MCI is not connected to OR gate

bit 12 OCNEN: OR Gate C Input Inverted Enable bit

1 = Inverted MCI is connected to OR gate

0 = Inverted MCI is not connected to OR gate

bit 11 OBEN: OR Gate B Input Enable bit

1 = MBI is connected to OR gate

0 = MBI is not connected to OR gate

bit 10 OBNEN: OR Gate B Input Inverted Enable bit

1 = Inverted MBI is connected to OR gate

0 = Inverted MBI is not connected to OR gate

bit 9 OAEN: OR Gate A Input Enable bit

1 = MAI is connected to OR gate

0 = MAI is not connected to OR gate

bit 8 OANEN: OR Gate A Input Inverted Enable bit

1 = Inverted MAI is connected to OR gate

0 = Inverted MAI is not connected to OR gate

bit 7 NAGS: AND Gate Output Inverted Enable bit

1 = Inverted ANDI is connected to OR gate

0 = Inverted ANDI is not connected to OR gate

bit 6 PAGS: AND Gate Output Enable bit

1 = ANDI is connected to OR gate

0 = ANDI is not connected to OR gate

bit 5 ACEN: AND Gate C Input Enable bit

1 = MCI is connected to AND gate

0 = MCI is not connected to AND gate

bit 4 ACNEN: AND Gate C Input Inverted Enable bit

1 = Inverted MCI is connected to AND gate

0 = Inverted MCI is not connected to AND gate

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 446  2009-2012 Microchip Technology Inc.

bit 3 ABEN: AND Gate B Input Enable bit

1 = MBI is connected to AND gate

0 = MBI is not connected to AND gate

bit 2 ABNEN: AND Gate B Input Inverted Enable bit

1 = Inverted MBI is connected to AND gate

0 = Inverted MBI is not connected to AND gate

bit 1 AAEN: AND Gate A Input Enable bit

1 = MAI is connected to AND gate

0 = MAI is not connected to AND gate

bit 0 AANEN: AND Gate A Input Inverted Enable bit

1 = Inverted MAI is connected to AND gate

0 = Inverted MAI is not connected to AND gate

CONTROL REGISTER (CONTINUED)

 2009-2012 Microchip Technology Inc. DS70616G-page 447

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 U-0 U-0 I-0

— — — — — — — —

bit 15 bit 8

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— CFSEL<2:0> CFLTREN CFDIV<2:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-7 Unimplemented: Read as ‘0’

bit 6-4 CFSEL<2:0>: Comparator Filter Input Clock Select bits

111 = T5CLK(1)

110 = T4CLK(2)

101 = T3CLK(1)

100 = T2CLK(2)

011 = SYNCO2(3)

010 = SYNCO1(3)

001 = FOSC(4)

000 = FP(4)

bit 3 CFLTREN: Comparator Filter Enable bit

1 = Digital filter is enabled

0 = Digital filter is disabled

bit 2-0 CFDIV<2:0>: Comparator Filter Clock Divide Select bits

111 = Clock Divide 1:128

110 = Clock Divide 1:64

101 = Clock Divide 1:32

100 = Clock Divide 1:16

011 = Clock Divide 1:8

010 = Clock Divide 1:4

001 = Clock Divide 1:2

000 = Clock Divide 1:1

Note 1: See the Type C Timer Block Diagram (Figure 13-2).

2: See the Type B Timer Block Diagram (Figure 13-1).

3: See the PWM Module Register Interconnect Diagram (Figure 16-2).

4: See the Oscillator System Diagram (Figure 9-1).

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 448  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0

— — — — — VREFSEL BGSEL<1:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

CVREN CVROE(1)CVRR CVRSS CVR<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-11 Unimplemented: Read as ‘0’

bit 10 VREFSEL: Voltage Reference Select bit

1 = CVREFIN = VREF+

0 = CVREFIN is generated by the resistor network

bit 9-8 BGSEL<1:0>: Band Gap Reference Source Select bits

11 = IVREF = VREF+(2)

10 = IVREF = 0.20V (nominal)

01 = IVREF = 0.60V (nominal)

00 = IVREF = 2.20V (nominal)

bit 7 CVREN: Comparator Voltage Reference Enable bit

1 = Comparator voltage reference circuit powered on

0 = Comparator voltage reference circuit powered down

bit 6 CVROE: Comparator Voltage Reference Output Enable bit(1)

1 = Voltage level is output on CVREF pin

0 = Voltage level is disconnected from CVREF pin

bit 5 CVRR: Comparator Voltage Reference Range Selection bit

1 = CVRSRC/24 step-size

0 = CVRSRC/32 step-size

bit 4 CVRSS: Comparator Voltage Reference Source Selection bit

1 = Comparator voltage reference source, CVRSRC = (VREF+) – (VREF-)(2)

0 = Comparator voltage reference source, CVRSRC = AVDD – AVSS

bit 3-0 CVR<3:0> Comparator Voltage Reference Value Selection 0  CVR<3:0>  15 bits

When CVRR = 1:

CVREFIN = (CVR<3:0>/24) • (CVRSRC)

When CVRR = 0:

CVREFIN = 1/4 • (CVRSRC) + (CVR<3:0>/32) • (CVRSRC)

Note 1: CVROE overrides the TRIS bit setting.

2: Selecting BGSEL<1:0> = 11 and CVRSS = 1 is invalid and will produce unpredictable results.

 2009-2012 Microchip Technology Inc. DS70616G-page 449

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

26.0 REAL-TIME CLOCK AND

CALENDAR (RTCC)

This chapter discusses the Real-Time Clock and

Calendar (RTCC) module and its operation.

Some of the key features of this module are:

• Time: Hours, Minutes and Seconds

• 24-Hour Format (military time)

• Calendar: Weekday, Date, Month and Year

• Alarm Configurable

• Year Range: 2000 to 2099

• Leap Year Correction

• BCD Format for Compact Firmware

• Optimized for Low-Power Operation

• User Calibration with Auto-Adjust

• Calibration Range: ±2.64 Seconds Error per Month

• Requirements: External 32.768 kHz Clock Crystal

• Alarm Pulse or Seconds Clock Output on RTCC Pin

The RTCC module is intended for applications where

accurate time must be maintained for extended periods

with minimum to no intervention from the CPU. The

RTCC module is optimized for low-power usage to pro-

vide extended battery lifetime while keeping track of

time.

The RTCC module is a 100-year clock and calendar

with automatic leap year detection. The range of the

clock is from 00:00:00 (midnight) on January 1, 2000 to

23:59:59 on December 31, 2099.

The hours are available in 24-hour (military time)

format. The clock provides a granularity of one second

with half-second visibility to the user.

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this

data sheet, refer to Section 29. “Real-

Time Clock and Calendar (RTCC)”

(DS70584) of the “dsPIC33E/PIC24E

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 450  2009-2012 Microchip Technology Inc.

FIGURE 26-1: RTCC BLOCK DIAGRAM

SOSCO

SOSCI

1Hz

SECONDS

MINUTES

HOUR

WEEKDAY

DATEMONTH

YEAR

SECONDS

MINUTES

HOUR

WEEKDAY

DATE

MONTH

RTCC Timer

RTCC Alarm

RTCPTR<1:0>

ALRMPTR<1:0>

RTCOE

RTCC

Set RTCIF Flag

RTSECSEL

RTCVAL

ALRMVAL

CAL<7:0>

32.768 kHz

Oscillator Prescaler

dsPIC33E/PIC24E

—

To g g l e

 2009-2012 Microchip Technology Inc. DS70616G-page 451

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

26.1 Writing to the RTCC Timer

The user application can configure the time and

calendar by writing the desired seconds, minutes,

hours, weekday, date, month and year to the RTCC

registers. Under normal operation, writes to the RTCC

Timer registers are not allowed. Attempted writes will

appear to execute normally, but the contents of the

registers will remain unchanged. To write to the RTCC

set. Setting the RTCWREN bit allows writes to the

RTCC registers. Conversely, clearing the RTCWREN

bit prevents writes.

To set the RTCWREN bit, the following procedure must

be executed. The RTCWREN bit can be cleared at any

time:

1. Write 0x55 to NVMKEY.

2. Write 0xAA to NVMKEY.

3. Set the RTCWREN bit using a single-cycle

instruction.

The RTCC module is enabled by setting the RTCEN bit

(RCFGCAL<15>). To set or clear the RTCEN bit, the

RTCWREN bit (RCFGCAL<13>) must be set.

If the entire clock (hours, minutes and seconds) needs

to be corrected, it is recommended that the RTCC

module should be disabled to avoid coincidental write

operation when the timer increments. Therefore, it

stops the clock from counting while writing to the RTCC

Timer register.

26.2 RTCC Resources

Many useful resources related to RTCC are provided

on the main product page of the Microchip web site for

the devices listed in this data sheet. This product page,

which can be accessed using this link, contains the

latest updates and additional information.

26.2.1 KEY RESOURCES

•Section 29. “Real-Time Clock and Calendar

(RTCC)” (DS70584) in the “dsPIC33E/PIC24E

Family Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

Note: To allow the RTCC module to be clocked by

the secondary crystal oscillator, the Sec-

ondary Oscillator Enable (LPOSCEN) bit in

the Oscillator Control (OSCCON<1>) regis-

ter must be set. For further details, refer to

Section 7. “Oscillator” (DS70580) in the

“dsPIC33E/PIC24E Family Reference

Manual”.

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 452  2009-2012 Microchip Technology Inc.

26.3 RTCC Registers

R/W-0 U-0 R/W-0 R-0 R-0 R/W-0 R/W-0 R/W-0

RTCEN(2)— RTCWREN RTCSYNC HALFSEC(3)RTCOE RTCPTR<1:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

CAL<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 RTCEN: RTCC Enable bit(2)

1 = RTCC module is enabled

0 = RTCC module is disabled

bit 14 Unimplemented: Read as ‘0’

bit 13 RTCWREN: RTCC Value Registers Write Enable bit

1 = RTCVAL register can be written to by the user application

0 = RTCVAL register is locked out from being written to by the user application

bit 12 RTCSYNC: RTCC Value Registers Read Synchronization bit

1 = A rollover is about to occur in 32 clock edges (approximately 1 ms)

0 = A rollover will not occur

bit 11 HALFSEC: Half-Second Status bit(3)

1 = Second half period of a second

0 = First half period of a second

bit 10 RTCOE: RTCC Output Enable bit

1 = RTCC output is enabled

0 = RTCC output is disabled

bit 9-8 RTCPTR<1:0>: RTCC Value Register Pointer bits

Points to the corresponding RTCC Value register when reading the RTCVAL register; the

RTCPTR<1:0> value decrements on every access of the RTCVAL register until it reaches ‘00’.

Note 1: The RCFGCAL register is only affected by a POR.

2: A write to the RTCEN bit is only allowed when RTCWREN = 1.

3: This bit is read-only. It is cleared when the lower half of the MINSEC register is written.

 2009-2012 Microchip Technology Inc. DS70616G-page 453

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

bit 7-0 CAL<7:0>: RTCC Drift Calibration bits

01111111 = Maximum positive adjustment; adds 508 RTCC clock pulses every one minute

•

00000001 = Minimum positive adjustment; adds four RTCC clock pulses every one minute

00000000 = No adjustment

11111111 = Minimum negative adjustment; subtracts four RTCC clock pulses every one minute

•

10000000 = Maximum negative adjustment; subtracts 512 RTCC clock pulses every one minute

Note 1: The RCFGCAL register is only affected by a POR.

2: A write to the RTCEN bit is only allowed when RTCWREN = 1.

3: This bit is read-only. It is cleared when the lower half of the MINSEC register is written.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 454  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0

— — — — — — RTSECSEL(1)PMPTTL

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-2 Unimplemented: Read as ‘0’

bit 1 RTSECSEL: RTCC Seconds Clock Output Select bit(1)

1 = RTCC seconds clock is selected for the RTCC pin

0 = RTCC alarm pulse is selected for the RTCC pin

bit 0 Not used by the RTCC module.

Note 1: To enable the actual RTCC output, the RTCOE bit (RCFGCAL<10>) must be set.

 2009-2012 Microchip Technology Inc. DS70616G-page 455

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

ALRMEN CHIME AMASK<3:0> ALRMPTR<1:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

ARPT<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 ALRMEN: Alarm Enable bit

1 = Alarm is enabled (cleared automatically after an alarm event whenever ARPT<7:0> = 0x00 and

CHIME = 0)

0 = Alarm is disabled

bit 14 CHIME: Chime Enable bit

1 = Chime is enabled; ARPT<7:0> bits are allowed to roll over from 0x00 to 0xFF

0 = Chime is disabled; ARPT<7:0> bits stop once they reach 0x00

bit 13-10 AMASK<3:0>: Alarm Mask Configuration bits

0000 = Every half second

0001 = Every second

0010 = Every 10 seconds

0011 = Every minute

0100 = Every 10 minutes

0101 = Every hour

0110 = Once a day

0111 = Once a week

1000 = Once a month

1001 = Once a year (except when configured for February 29th, once every 4 years)

101x = Reserved – do not use

11xx = Reserved – do not use

bit 9-8 ALRMPTR<1:0>: Alarm Value Register Window Pointer bits

Points to the corresponding Alarm Value registers when reading the ALRMVAL register. The

ALRMPTR<1:0> value decrements on every read or write of ALRMVAL until it reaches ‘00’.

bit 7-0 ARPT<7:0>: Alarm Repeat Counter Value bits

11111111 = Alarm will repeat 255 more times

•

00000000 = Alarm will not repeat

The counter decrements on any alarm event. The counter is prevented from rolling over from 0x00 to

0xFF unless CHIME = 1.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 456  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

YRTEN<3:0> YRONE<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-8 Unimplemented: Read as ‘0’

bit 7-4 YRTEN<3:0>: Binary Coded Decimal Value of Year’s Tens Digit bits

Contains a value from 0 to 9.

bit 3-0 YRONE<3:0>: Binary Coded Decimal Value of Year’s Ones Digit bits

Contains a value from 0 to 9.

Note 1: A write to the YEAR register is only allowed when RTCWREN = 1.

U-0 U-0 U-0 R-x R-x R-x R-x R-x

— — —

MTHTEN0 MTHONE<3:0>

bit 15 bit 8

U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

— —

DAYTEN<1:0> DAYONE<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-13 Unimplemented: Read as ‘0’

bit 12 MTHTEN0: Binary Coded Decimal Value of Month’s Tens Digit bit

Contains a value of 0 or 1.

bit 11-8 MTHONE<3:0>: Binary Coded Decimal Value of Month’s Ones Digit bits

Contains a value from 0 to 9.

bit 7-6 Unimplemented: Read as ‘0’

bit 5-4 DAYTEN<1:0>: Binary Coded Decimal Value of Day’s Tens Digit bits

Contains a value from 0 to 3.

bit 3-0 DAYONE<3:0>: Binary Coded Decimal Value of Day’s Ones Digit bits

Contains a value from 0 to 9.

Note 1: A write to this register is only allowed when RTCWREN = 1.

 2009-2012 Microchip Technology Inc. DS70616G-page 457

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

U-0 U-0 U-0 U-0 U-0 R/W-x R/W-x R/W-x

— — — — — WDAY<2:0>

bit 15 bit 8

U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

—— HRTEN<1:0> HRONE<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-11 Unimplemented: Read as ‘0’

bit 10-8 WDAY<2:0>: Binary Coded Decimal Value of Weekday Digit bits

Contains a value from 0 to 6.

bit 7-6 Unimplemented: Read as ‘0’

bit 5-4 HRTEN<1:0>: Binary Coded Decimal Value of Hour’s Tens Digit bits

Contains a value from 0 to 2.

bit 3-0 HRONE<3:0>: Binary Coded Decimal Value of Hour’s Ones Digit bits

Contains a value from 0 to 9.

Note 1: A write to this register is only allowed when RTCWREN = 1.

U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

— MINTEN<2:0> MINONE<3:0>

bit 15 bit 8

U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

— SECTEN<2:0> SECONE<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-12 MINTEN<2:0>: Binary Coded Decimal Value of Minute’s Tens Digit bits

Contains a value from 0 to 5.

bit 11-8 MINONE<3:0>: Binary Coded Decimal Value of Minute’s Ones Digit bits

Contains a value from 0 to 9.

bit 7 Unimplemented: Read as ‘0’

bit 6-4 SECTEN<2:0>: Binary Coded Decimal Value of Second’s Tens Digit bits

Contains a value from 0 to 5.

bit 3-0 SECONE<3:0>: Binary Coded Decimal Value of Second’s Ones Digit bits

Contains a value from 0 to 9.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 458  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x

— — —

MTHTEN0 MTHONE<3:0>

bit 15 bit 8

U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

— —

DAYTEN<1:0> DAYONE<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-13 Unimplemented: Read as ‘0’

bit 12 MTHTEN0: Binary Coded Decimal Value of Month’s Tens Digit bit

Contains a value of 0 or 1.

bit 11-8 MTHONE<3:0>: Binary Coded Decimal Value of Month’s Ones Digit bits

Contains a value from 0 to 9.

bit 7-6 Unimplemented: Read as ‘0’

bit 5-4 DAYTEN<1:0>: Binary Coded Decimal Value of Day’s Tens Digit bits

Contains a value from 0 to 3.

bit 3-0 DAYONE<3:0>: Binary Coded Decimal Value of Day’s Ones Digit bits

Contains a value from 0 to 9.

Note 1: A write to this register is only allowed when RTCWREN = 1.

 2009-2012 Microchip Technology Inc. DS70616G-page 459

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

VALUE REGISTER(1)

U-0 U-0 U-0 U-0 U-0 R/W-x R/W-x R/W-x

— — — — — WDAY2 WDAY1 WDAY0

bit 15 bit 8

U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

—— HRTEN<1:0> HRONE<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-11 Unimplemented: Read as ‘0’

bit 10-8 WDAY<2:0>: Binary Coded Decimal Value of Weekday Digit bits

Contains a value from 0 to 6.

bit 7-6 Unimplemented: Read as ‘0’

bit 5-4 HRTEN<1:0>: Binary Coded Decimal Value of Hour’s Tens Digit bits

Contains a value from 0 to 2.

bit 3-0 HRONE<3:0>: Binary Coded Decimal Value of Hour’s Ones Digit bits

Contains a value from 0 to 9.

Note 1: A write to this register is only allowed when RTCWREN = 1.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 460  2009-2012 Microchip Technology Inc.

VALUE REGISTER

U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

— MINTEN<2:0> MINONE<3:0>

bit 15 bit 8

U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x

— SECTEN<2:0> SECONE<3:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 Unimplemented: Read as ‘0’

bit 14-12 MINTEN<2:0>: Binary Coded Decimal Value of Minute’s Tens Digit bits

Contains a value from 0 to 5.

bit 11-8 MINONE<3:0>: Binary Coded Decimal Value of Minute’s Ones Digit bits

Contains a value from 0 to 9.

bit 7 Unimplemented: Read as ‘0’

bit 6-4 SECTEN<2:0>: Binary Coded Decimal Value of Second’s Tens Digit bits

Contains a value from 0 to 5.

bit 3-0 SECONE<3:0>: Binary Coded Decimal Value of Second’s Ones Digit bits

Contains a value from 0 to 9.

 2009-2012 Microchip Technology Inc. DS70616G-page 461

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

27.0 PROGRAMMABLE CYCLIC

REDUNDANCY CHECK (CRC)

GENERATOR

The programmable CRC generator offers the following

features:

• User-Programmable (up to 32nd order)

Polynomial CRC Equation

• Interrupt Output

• Data FIFO

The programmable CRC generator provides a

hardware implemented method of quickly generating

checksums for various networking and security

applications. It offers the following features:

• User-Programmable CRC Polynomial Equation,

up to 32 bits

• Programmable Shift Direction (little or big-endian)

• Independent Data and Polynomial Lengths

• Configurable Interrupt Output

• Data FIFO

A simplified block diagram of the CRC generator is

shown in Figure 27-1. A simple version of the CRC shift

engine is shown in Figure 27-2.

FIGURE 27-1: PROGRAMMABLE CRC BLOCK DIAGRAM

FIGURE 27-2: CRC SHIFT ENGINE DETAIL

Note 1: This data sheet summarizes the features of

the dsPIC33EPXXX(GP/MC/MU)806/810/

814 and PIC24EPXXX(GP/GU)810/814

families of devices. It is not intended to be

a comprehensive reference source. To

complement the information in this data

sheet, refer to Section 27. “Programma-

ble Cyclic Redundancy Check (CRC)”

(DS70346) of the “dsPIC33E/PIC24E

Family Reference Manual”, which is

available from the Microchip web site

(www.microchip.com).

2: Some registers and associated bits

described in this section may not be available

on all devices. Refer to Section 4.0 “Mem-

ory Organization” in this data sheet for

device-specific register and bit information.

Variable FIFO

(4x32, 8x16 or 16x8)

CRCDATH CRCDATL

Shift Buffer

CRC Shift Engine

CRCWDATH CRCWDATL

LENDIAN

CRCISEL

FIFO Empty Event

Shift Complete Event

Set CRCIF

2 * FP Shift Clock

CRCWDATH CRCWDATL

Bit 0 Bit 1 Bit n(2)

X(1)(1)

Read/Write Bus

Shift Buffer

Data Bit 2

X(2)(1) X(n)(1)

Note 1: Each XOR stage of the shift engine is programmable. See text for details.

2: Polynomial Length n is determined by ([PLEN<4:0>] + 1).

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 462  2009-2012 Microchip Technology Inc.

27.1 Overview

The CRC module can be programmed for CRC

polynomials of up to the 32nd order, using up to 32 bits.

Polynomial length, which reflects the highest exponent

in the equation, is selected by the PLEN<4:0> bits

(CRCCON2<4:0>).

The CRCXORL and CRCXORH registers control which

exponent terms are included in the equation. Setting a

particular bit includes that exponent term in the

equation; functionally, this includes an XOR operation

on the corresponding bit in the CRC engine. Clearing

the bit disables the XOR.

For example, consider two CRC polynomials, one a

16-bit equation and the other a 32-bit equation:

To program these polynomials into the CRC generator,

set the register bits as shown in Tab le 2 7 - 1.

Note that the appropriate positions are set to ‘1’ to indicate

that they are used in the equation (for example, X26 and

X23). The 0 bit required by the equation is always XORed;

thus, X0 is a don’t care. For a polynomial of length, N, it is

assumed that the Nth bit will always be used, regardless

of the bit setting. Therefore, for a polynomial length of 32,

there is no 32nd bit in the CRCxOR register.

TABLE 27-1: CRC SETUP EXAMPLES FOR

16 AND 32-BIT POLYNOMIAL

27.2 Programmable CRC Resources

Many useful resources related to Programmable CRC

are provided on the main product page of the Microchip

web site for the devices listed in this data sheet. This

product page, which can be accessed using this link,

contains the latest updates and additional information.

27.2.1 KEY RESOURCES

•Section 27. “Programmable Cyclic Redundancy

Check (CRC)” (DS70346) in the “dsPIC33E/

PIC24E Family Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

x16 + x12 + x5 + 1

and

x32 + x26 + x23 + x22 + x16 + x12 + x11 + x10 + x8 + x7

+ x5 + x4 + x2 + x + 1

CRC

Control Bits

Bit Values

16-Bit

Polynomial

32-Bit

Polynomial

PLEN<4:0> 01111 11111

X<31:16> 0000 0000

0000 000x

0000 0100

1100 0001

X<15:0> 0001 0000

0010 000x

0001 1101

1011 011x

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

 2009-2012 Microchip Technology Inc. DS70616G-page 463

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

27.3 Programmable CRC Registers

R/W-0 U-0 R/W-0 R-0 R-0 R-0 R-0 R-0

CRCEN — CSIDL VWORD<4:0>

bit 15 bit 8

R-0 R-1 R/W-0 R/W-0 R/W-0 U-0 U-0 U-0

CRCFUL CRCMPT CRCISEL CRCGO LENDIAN — — —

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 CRCEN: CRC Enable bit

1 = CRC module is enabled

0 = CRC module is disabled, all state machines, pointers and CRCWDAT/CRCDAT are reset; other

SFRs are not reset

bit 14 Unimplemented: Read as ‘0’

bit 13 CSIDL: CRC Stop in Idle Mode bit

1 = Discontinues module operation when device enters Idle mode

0 = Continues module operation in Idle mode

bit 12-8 VWORD<4:0>: Pointer Value bits

Indicates the number of valid words in the FIFO. Has a maximum value of 8 when PLEN<4:0> > 7 or

16 when PLEN<4:0> 7.

bit 7 CRCFUL: FIFO Full bit

1 = FIFO is full

0 = FIFO is not full

bit 6 CRCMPT: FIFO Empty Bit

1 = FIFO is empty

0 = FIFO is not empty

bit 5 CRCISEL: CRC Interrupt Selection bit

1 = Interrupt on FIFO is empty; final word of data is still shifting through CRC

0 = Interrupt on shift is complete and CRCWDAT results are ready

bit 4 CRCGO: Start CRC bit

1 = Starts CRC serial shifter

0 = CRC serial shifter is turned off

bit 3 LENDIAN: Data Word Little-Endian Configuration bit

1 = Data word is shifted into the CRC starting with the LSb (little endian)

0 = Data word is shifted into the CRC starting with the MSb (big endian)

bit 2-0 Unimplemented: Read as ‘0’

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 464  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— — — DWIDTH<4:0>

bit 15 bit 8

U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— — — PLEN<4:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-13 Unimplemented: Read as ‘0’

bit 12-8 DWIDTH<4:0>: Data Width Select bits

These bits set the width of the data word (DWIDTH<4:0> + 1).

bit 7-5 Unimplemented: Read as ‘0’

bit 4-0 PLEN<4:0>: Polynomial Length Select bits

These bits set the length of the polynomial (Polynomial Length = PLEN<4:0> + 1).

 2009-2012 Microchip Technology Inc. DS70616G-page 465

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

X<31:24>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

X<23:16>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 X<31:16>: XOR of Polynomial Term Xn Enable bits

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

X<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0

X<7:1> —

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-1 X<15:1>: XOR of Polynomial Term Xn Enable bits

bit 0 Unimplemented: Read as ‘0’

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 466  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 467

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

28.0 PARALLEL MASTER PORT

(PMP)

The Parallel Master Port (PMP) module is a parallel

8-bit I/O module, specifically designed to communi-

cate with a wide variety of parallel devices, such as

communication peripherals, LCDs, external memory

devices and microcontrollers. Because the interface

to parallel peripherals varies significantly, the PMP is

highly configurable.

Key features of the PMP module include:

• Eight Data Lines

• Up to 16 Programmable Address Lines

• Up to 2 Chip Select Lines

• Programmable Strobe Options:

- Individual read and write strobes, or

- Read/Write strobe with enable strobe

• Address Auto-Increment/Auto-Decrement

• Programmable Address/Data Multiplexing

• Programmable Polarity on Control Signals

• Legacy Parallel Slave Port (PSP) Support

• Enhanced Parallel Slave Support:

- Address support

- 4-byte deep auto-incrementing buffer

• Programmable Wait States

FIGURE 28-1: PMP MODULE PINOUT AND CONNECTIONS TO EXTERNAL DEVICES

Note 1: This data sheet summarizes the features

of the dsPIC33EPXXX(GP/MC/MU)806/

810/814 and PIC24EPXXX(GP/GU)810/

814 families of devices. It is not intended

to be a comprehensive reference source.

To complement the information in this data

sheet, refer to Section 28. “Parallel Mas-

ter Port (PMP)” (DS70576) of the

“dsPIC33E/PIC24E Family Reference

Manual”, which is available from the

Microchip web site (www.microchip.com).

2: Some registers and associated bits

described in this section may not be

available on all devices. Refer to

Section 4.0 “Memory Organization” in

this data sheet for device-specific register

and bit information.

PMA<0>

PMA<14>

PMA<15>

PMBE

PMRD

PMWR

PMD<7:0>

PMENB

PMRD/PMWR

PMCS1

PMA<1>

PMA<13:2>

PMALL

PMALH

PMA<7:0>

PMA<15:8>

PMCS2

EEPROM

Address Bus

Data Bus

Control Lines

dsPIC33E/PIC24E

LCD FIFO

Microcontroller

8-Bit Data (with or without multiplexed addressing)

Up to 16-Bit Address

Parallel Master Port

Buffer

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 468  2009-2012 Microchip Technology Inc.

28.1 PMP Resources

Many useful resources related to PMP are provided on

the main product page of the Microchip web site for the

devices listed in this data sheet. This product page,

which can be accessed using this link, contains the

latest updates and additional information.

28.1.1 KEY RESOURCES

•Section 28. “Parallel Master Port (PMP)”

(DS70576) in the “dsPIC33E/PIC24E Family

Reference Manual”

• Code Samples

• Application Notes

• Software Libraries

• Webinars

• All related “dsPIC33E/PIC24E Family Reference

Manual” Sections

• Development Tools

Note: In the event you are not able to access the

product page using the link above, enter

this URL in your browser:

http://www.microchip.com/wwwproducts/

Devices.aspx?dDocName=en554310

 2009-2012 Microchip Technology Inc. DS70616G-page 469

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

28.2 PMP Control Registers

R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PMPEN — PSIDL ADRMUX<1:0> PTBEEN PTWREN PTRDEN

bit 15 bit 8

R/W-0 R/W-0 R/W-0(1)R/W-0(1)R/W-0(1)R/W-0 R/W-0 R/W-0

CSF<1:0> ALP CS2P CS1P BEP WRSP RDSP

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at Reset ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 PMPEN: Parallel Master Port Enable bit

1 = PMP module is enabled

0 = PMP module is disabled, no off-chip access is performed

bit 14 Unimplemented: Read as ‘0’

bit 13 PSIDL: PMP Stop in Idle Mode bit

1 = Discontinues module operation when device enters Idle mode

0 = Continues module operation in Idle mode

bit 12-11 ADRMUX<1:0>: Address/Data Multiplexing Selection bits

11 = Reserved

10 = All 16 bits of address are multiplexed on PMD<7:0> pins

01 = Lower eight bits of address are multiplexed on PMD<7:0> pins, upper eight bits are on PMA<15:8>

00 = Address and data appear on separate pins

bit 10 PTBEEN: Byte Enable Port Enable bit (16-Bit Master mode)

1 = PMBE port is enabled

0 = PMBE port is disabled

bit 9 PTWREN: Write Enable Strobe Port Enable bit

1 = PMWR/PMENB port is enabled

0 = PMWR/PMENB port is disabled

bit 8 PTRDEN: Read/Write Strobe Port Enable bit

1 = PMRD/PMWR port is enabled

0 = PMRD/PMWR port is disabled

bit 7-6 CSF<1:0>: Chip Select Function bits

11 = Reserved

10 = PMCS1 and PMCS2 function as Chip Select

01 = PMCS2 functions as Chip Select, PMCS1 functions as Address Bit 14

00 = PMCS1 and PMCS2 function as Address Bits 15 and 14

bit 5 ALP: Address Latch Polarity bit(1)

1 = Active-high (PMALL and PMALH)

0 = Active-low (PMALL and PMALH)

bit 4 CS2P: Chip Select 1 Polarity bit(1)

1 = Active-high (PMCS2)

0 = Active-low (PMCS2)

Note 1: These bits have no effect when their corresponding pins are used as address lines.

2: PMCS1 applies to Master mode and PMCS applies to Slave mode.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 470  2009-2012 Microchip Technology Inc.

bit 3 CS1P: Chip Select 0 Polarity bit(1)

1 = Active-high (PMCS1/PMCS)(2)

0 = Active-low (PMCS1/PMCS)

bit 2 BEP: Byte Enable Polarity bit

1 = Byte enable active-high (PMBE)

0 = Byte enable active-low (PMBE)

bit 1 WRSP: Write Strobe Polarity bit

For Slave Modes and Master Mode 2 (PMMODE<9:8> = 00, 01, 10):

1 = Write strobe is active-high (PMWR)

0 = Write strobe is active-low (PMWR)

For Master Mode 1 (PMMODE<9:8> = 11):

1 = Enables strobe active-high (PMENB)

0 = Enables strobe active-low (PMENB)

bit 0 RDSP: Read Strobe Polarity bit

For Slave Modes and Master Mode 2 (PMMODE<9:8> = 00, 01, 10):

1 = Read strobe is active-high (PMRD)

0 = Read strobe is active-low (PMRD)

For Master Mode 1 (PMMODE<9:8> = 11):

1 = Enables strobe active-high (PMRD/PMWR)

0 = Enables strobe active-low (PMRD/PMWR)

Note 1: These bits have no effect when their corresponding pins are used as address lines.

2: PMCS1 applies to Master mode and PMCS applies to Slave mode.

 2009-2012 Microchip Technology Inc. DS70616G-page 471

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

BUSY IRQM<1:0> INCM<1:0> MODE16 MODE<1:0>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

WAITB<1:0>(1,2,3)WAITM<3:0> WAITE<1:0>(1,2,3)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at Reset ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 BUSY: Busy bit (Master mode only)

1 = Port is busy

0 = Port is not busy

bit 14-13 IRQM<1:0>: Interrupt Request Mode bits

11 = Interrupt is generated when Read Buffer 3 is read or Write Buffer 3 is written (Buffered PSP

mode), or on a read/write operation when PMA<1:0> = 11 (Addressable PSP mode only)

10 = Reserved

01 = Interrupt is generated at the end of the read/write cycle

00 = No Interrupt is generated

bit 12-11 INCM<1:0>: Increment Mode bits

11 = PSP read and write buffers auto-increment (Legacy PSP mode only)

10 = Decrements ADDR by 1 every read/write cycle

01 = Increments ADDR by 1 every read/write cycle

00 = No increment or decrement of address

bit 10 MODE16: Parallel Master Port Mode 8/16-Bit Mode bit

1 = 16-bit mode: data register is 16 bits, a read/write to the data register invokes two 8-bit transfers

0 = 8-bit mode: data register is 8 bits, a read/write to the data register invokes one 8-bit transfer

bit 9-8 MODE<1:0>: Parallel Master Port Mode Select bits

11 = Master Mode 1 (PMCSx, PMRD/PMWR, PMENB, PMBE, PMA<x:0> and PMD<7:0>)

10 = Master Mode 2 (PMCSx, PMRD, PMWR, PMBE, PMA<x:0> and PMD<7:0>)

01 = Enhanced PSP, controls signals (PMRD, PMWR, PMCSx, PMD<7:0> and PMA<1:0>)

00 = Legacy Parallel Slave Port, controls signals (PMRD, PMWR, PMCSx and PMD<7:0>)

bit 7-6 WAITB<1:0>: Data Setup to Read/Write/Address Phase Wait State Configuration bits(1,2,3)

11 = Data wait of 4 TP (demultiplexed/multiplexed); address phase of 4 TP (multiplexed)

10 = Data wait of 3 TP (demultiplexed/multiplexed); address phase of 3 TP (multiplexed)

01 = Data wait of 2 TP (demultiplexed/multiplexed); address phase of 2 TP (multiplexed)

00 = Data wait of 1 TP (demultiplexed/multiplexed); address phase of 1 TP (multiplexed)

bit 5-2 WAITM<3:0>: Read to Byte Enable Strobe Wait State Configuration bits

1111 = Wait of additional 15 TP

•

0001 = Wait of additional 1 TP

0000 = No additional Wait cycles (operation forced into one TP)

Note 1: The applied Wait state depends on whether data and address are multiplexed or demultiplexed. See

Section 28.4.1.8. “Wait States” in Section 28. “Parallel Master Port (PMP)” (DS70576) in the

“dsPIC33E/PIC24E Family Reference Manual” for more information.

2: WAITB<1:0> and WAITE<1:0> bits are ignored whenever WAITM<3:0> = 0000.

3: TP = 1/FP.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 472  2009-2012 Microchip Technology Inc.

bit 1-0 WAITE<1:0>: Data Hold After Strobe Wait State Configuration bits(1,2,3)

11 = Wait of 4 TP

10 = Wait of 3 TP

01 = Wait of 2 TP

00 = Wait of 1 TP

Note 1: The applied Wait state depends on whether data and address are multiplexed or demultiplexed. See

Section 28.4.1.8. “Wait States” in Section 28. “Parallel Master Port (PMP)” (DS70576) in the

“dsPIC33E/PIC24E Family Reference Manual” for more information.

2: WAITB<1:0> and WAITE<1:0> bits are ignored whenever WAITM<3:0> = 0000.

3: TP = 1/FP.

 2009-2012 Microchip Technology Inc. DS70616G-page 473

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

(MASTER MODES ONLY)(1)

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

CS2 CS1 ADDR<13:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

ADDR<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at Reset ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 CS2: Chip Select 2 bit

If PMCON<7:6> = 10 or 01:

1 = Chip Select 2 is active

0 = Chip Select 2 is inactive

If PMCON<7:6> = 11 or 00:

Bit functions as ADDR<15>.

bit 14 CS1: Chip Select 1 bit

If PMCON<7:6> = 10:

1 = Chip Select 1 is active

0 = Chip Select 1 is inactive

If PMCON<7:6> = 11 or 0x:

Bit functions as ADDR<14>.

bit 13-0 ADDR<13:0>: Destination Address bits

Note 1: In Enhanced Slave mode, PMADDR functions as PMDOUT1, one of the two Data Buffer registers.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 474  2009-2012 Microchip Technology Inc.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PTEN15 PTEN14 PTEN13 PTEN12 PTEN11 PTEN10 PTEN9 PTEN8

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PTEN7 PTEN6 PTEN5 PTEN4 PTEN3 PTEN2 PTEN1 PTEN0

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at Reset ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 PTEN15: PMCS2 Strobe Enable bit

1 = PMA15 functions as either PMA<15> or PMCS2

0 = PMA15 functions as port I/O

bit 14 PTEN14: PMCS1 Strobe Enable bit

1 = PMA14 functions as either PMA<14> or PMCS1

0 = PMA14 functions as port I/O

bit 13-2 PTEN<13:2>: PMP Address Port Enable bits

1 = PMA<13:2> function as PMP address lines

0 = PMA<13:2> function as port I/O

bit 1-0 PTEN<1:0>: PMALH/PMALL Strobe Enable bits

1 = PMA1 and PMA0 function as either PMA<1:0> or PMALH and PMALL

0 = PMA1 and PMA0 function as port I/O

 2009-2012 Microchip Technology Inc. DS70616G-page 475

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

R-0 R/W-0, HS U-0 U-0 R-0 R-0 R-0 R-0

IBF IBOV —— IB3F IB2F IB1F IB0F

bit 15 bit 8

R-1 R/W-0, HS U-0 U-0 R-1 R-1 R-1 R-1

OBE OBUF —— OB3EOB2EOB1EOB0E

bit 7 bit 0

Legend: HS = Hardware Settable bit

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at Reset ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 IBF: Input Buffer Full Status bit

1 = All writable Input Buffer registers are full

0 = Some or all of the Writable Input Buffer registers are empty

bit 14 IBOV: Input Buffer Overflow Status bit

1 = A write attempt to a full Input Byte register occurred (must be cleared in software)

0 = No overflow occurred

bit 13-12 Unimplemented: Read as ‘0’

bit 11-8 IB3F:IB0F: Input Buffer x Status Full bits

1 = Input buffer contains data that has not been read (reading the buffer will clear this bit)

0 = Input buffer does not contain any unread data

bit 7 OBE: Output Buffer Empty Status bit

1 = All readable Output Buffer registers are empty

0 = Some or all of the readable Output Buffer registers are full

bit 6 OBUF: Output Buffer Underflow Status bit

1 = A read occurred from an empty output byte register (must be cleared in software)

0 = No underflow occurred

bit 5-4 Unimplemented: Read as ‘0’

bit 3-0 OB3E:OB0E: Output Buffer x Status Empty bits

1 = Output buffer is empty (writing data to the buffer will clear this bit)

0 = Output buffer contains data that has not been transmitted

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 476  2009-2012 Microchip Technology Inc.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0

— — — — — — RTSECSEL PMPTTL

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-2 Unimplemented: Read as ‘0’

bit 1 Not used by the PMP module.

bit 0 PMPTTL: PMP Module TTL Input Buffer Select bit

1 = PMP module uses TTL input buffers

0 = PMP module uses Schmitt Trigger input buffers

 2009-2012 Microchip Technology Inc. DS70616G-page 477

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

29.0 SPECIAL FEATURES

dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices include

several features intended to maximize application

flexibility and reliability, and minimize cost through

elimination of external components. These are:

• Flexible Configuration

• Watchdog Timer (WDT)

• Code Protection and CodeGuard™ Security

• JTAG Boundary Scan Interface

• In-Circuit Serial Programming™ (ICSP™)

• In-Circuit Emulation

29.1 Configuration Bits

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices provide

nonvolatile memory implementation for device Configu-

ration bits. Refer to Section 30. “Device Configuration”

(DS70618) of the “dsPIC33E/PIC24E Family Reference

Manual” for more information on this implementation.

The Configuration bits can be programmed (read as

‘0’), or left unprogrammed (read as ‘1’), to select

various device configurations. These bits are mapped,

starting at program memory location, 0xF80000.

The individual Configuration bit descriptions for the

Configuration registers are shown in Table 29-2.

Note that address, 0xF80000, is beyond the user

program memory space. It belongs to the configuration

memory space (0x800000-0xFFFFFF), which can only

be accessed using table reads and table writes.

To prevent inadvertent configuration changes during

code execution, some programmable Configuration

bits are write-once. For such bits, changing a device

configuration requires that the device be reset. For

other Configuration bits, the device configuration

changes immediately after an RTSP operation. The

RTSP effect column in Table 29-2 indicates when the

device configuration changes after a bit is modified

using RTSP.

The device Configuration register map is shown in

Table 29-1.

Note: This data sheet summarizes the features of

the dsPIC33EPXXX(GP/MC/MU)806/810/

814 and PIC24EPXXX(GP/GU)810/814

families of devices. It is not intended to be a

comprehensive reference source. To

complement the information in this data

sheet, refer to the related section of the

“dsPIC33E/PIC24E Family Reference

Manual”, which is available from the

Microchip web site (www.microchip.com).

TABLE 29-1: DEVICE CONFIGURATION REGISTER MAP

Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

0xF80000 Reserved — — — — — — — —

0xF80002 Reserved — — — — — — — —

0xF80004 FGS —— GSSK<1:0> ——GSSGWRP

0xF80006 FOSCSEL IESO — — — —FNOSC<2:0>

0xF80008 FOSC FCKSM<1:0> IOL1WAY —— OSCIOFNC POSCMD<1:0>

0xF8000A FWDT FWDTEN WINDIS PLLKEN WDTPRE WDTPOST<3:0>

0xF8000C FPOR — — ALTI2C2 ALTI2C1 BOREN(2)FPWRT<2:0>

0xF8000E FICD Reserved(1)JTAGEN Reserved(1)— RSTPRI ICS<1:0>

0xF80010 FAS —— APLK<1:0> —— APL AWRP

0xF80012 FUID0 User Unit ID Byte 0

Legend: — = unimplemented bit, read as ‘0’

Note 1: These bits are reserved for use by development tools and must be programmed as ‘1’.

2: BOR should always be enabled for proper operation (BOREN = 1).

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 478  2009-2012 Microchip Technology Inc.

TABLE 29-2: CONFIGURATION BITS DESCRIPTION

Bit Field Register RTSP Effect Description

GSSK<1:0> FGS Immediate General Segment Key bits

These bits must be set to ‘00’ if GWRP = 1 and GSS = 1. These bits must

be set to ‘11’ for any other value of the GWRP and GSS bits.

Any mismatch between either the GWRP or GSS bits, and the GSSK bits

(as described above), will result in code protection becoming enabled for

the General Segment. A Flash bulk erase will be required to unlock the

device.

GSS FGS Immediate General Segment Code-Protect bit

1 = User program memory is not code-protected

0 = User program memory is code-protected

GWRP FGS Immediate General Segment Write-Protect bit

1 = User program memory is not write-protected

0 = User program memory is write-protected

IESO FOSCSEL Immediate Two-Speed Oscillator Start-up Enable bit

1 = Start-up device with FRC, then automatically switch to the

user-selected oscillator source when ready

0 = Start-up device with user-selected oscillator source

FNOSC<2:0> FOSCSEL If clock switch

is enabled, the

RTSP effect is

on any device

Reset;

otherwise,

immediate

Initial Oscillator Source Selection bits

111 = Internal Fast RC (FRC) Oscillator with Postscaler

110 = Internal Fast RC (FRC) Oscillator with Divide-by-16

101 = LPRC Oscillator

100 = Secondary (LP) Oscillator

011 = Primary (XT, HS, EC) Oscillator with PLL

010 = Primary (XT, HS, EC) Oscillator

001 = Internal Fast RC (FRC) Oscillator with PLL

000 = FRC Oscillator

FCKSM<1:0> FOSC Immediate Clock Switching Mode bits

1x = Clock switching is disabled, Fail-Safe Clock Monitor is disabled

01 = Clock switching is enabled, Fail-Safe Clock Monitor is disabled

00 = Clock switching is enabled, Fail-Safe Clock Monitor is enabled

IOL1WAY FOSC Immediate Peripheral Pin Select Configuration bit

1 = Allows only one reconfiguration

0 = Allows multiple reconfigurations

OSCIOFNC FOSC Immediate OSC2 Pin Function bit (except in XT and HS modes)

1 = OSC2 is the clock output

0 = OSC2 is the general purpose digital I/O pin

POSCMD<1:0> FOSC Immediate Primary Oscillator Mode Select bits

11 = Primary Oscillator is disabled

10 = HS Crystal Oscillator mode

01 = XT Crystal Oscillator mode

00 = EC (External Clock) mode

FWDTEN FWDT Immediate Watchdog Timer Enable bit

1 = Watchdog Timer is always enabled (LPRC Oscillator cannot be disabled.

Clearing the SWDTEN bit in the RCON register has no effect.)

0 = Watchdog Timer is enabled/disabled by user software (LPRC can be

disabled by clearing the SWDTEN bit in the RCON register.)

Note 1: BOR should always be enabled for proper operation (BOREN = 1).

2: This register can only be modified when code protection and write protection are disabled for both the

General and Auxiliary Segments (APL = 1, AWRP = 1, APLK = 0, GSS = 1, GWRP = 1 and GSSK = 0).

 2009-2012 Microchip Technology Inc. DS70616G-page 479

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

WINDIS FWDT Immediate Watchdog Timer Window Enable bit

1 = Watchdog Timer is in Non-Window mode

0 = Watchdog Timer is in Window mode

PLLKEN FWDT Immediate PLL Lock Wait Enable bit

1 = Clock switches to the PLL source will wait until the PLL lock signal is valid

0 = Clock switch will not wait for PLL lock

WDTPRE FWDT Immediate Watchdog Timer Prescaler bit

1 = 1:128

0 = 1:32

APLK<1:0> FAS(2)Immediate Auxiliary Segment Key bits

These bits must be set to ‘00’ if AWRP = 1 and APL = 1. These bits must

be set to ‘11’ for any other value of the AWRP and APL bits.

Any mismatch between either the AWRP or APL bits and the APLK bits

(as described above), will result in code protection becoming enabled for

the Auxiliary Segment. A Flash bulk erase will be required to unlock the

device.

APL FAS(2)Immediate Auxiliary Segment Code-Protect bit

1 = Auxiliary program memory is not code-protected

0 = Auxiliary program memory is code-protected

AWRP FAS(2)Immediate Auxiliary Segment Write-Protect bit

1 = Auxiliary program memory is not write-protected

0 = Auxiliary program memory is write-protected

WDTPOST<3:0> FWDT Immediate Watchdog Timer Postscaler bits

1111 = 1:32,768

1110 = 1:16,384

•

0001 = 1:2

0000 = 1:1

FPWRT<2:0> FPOR Immediate Power-on Reset Timer Value Select bits

111 = PWRT = 128 ms

110 = PWRT = 64 ms

101 = PWRT = 32 ms

100 = PWRT = 16 ms

011 = PWRT = 8 ms

010 = PWRT = 4 ms

001 = PWRT = 2 ms

000 = PWRT = Disabled

BOREN(1)FPOR Immediate Brown-out Reset (BOR) Detection Enable bit

1 = BOR is enabled

0 = BOR is disabled

ALTI2C2 FPOR Immediate Alternate I2C™ pins for I2C2 bit

1 = I2C2 is mapped to the SDA2/SCL2 pins

0 = I2C2 is mapped to the ASDA2/ASCL2 pins

ALTI2C1 FPOR Immediate Alternate I2C pins for I2C1 bit

1 = I2C1 is mapped to the SDA1/SCL1 pins

0 = I2C1 is mapped to the ASDA1/ASCL1 pins

TABLE 29-2: CONFIGURATION BITS DESCRIPTION (CONTINUED)

Bit Field Register RTSP Effect Description

Note 1: BOR should always be enabled for proper operation (BOREN = 1).

2: This register can only be modified when code protection and write protection are disabled for both the

General and Auxiliary Segments (APL = 1, AWRP = 1, APLK = 0, GSS = 1, GWRP = 1 and GSSK = 0).

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 480  2009-2012 Microchip Technology Inc.

JTAGEN FICD ImmediateJTAG Enable bit

1 = JTAG is enabled

0 = JTAG is disabled

RSTPRI FICD On any

device Reset

Reset Target Vector Select bit

1 = Device will reset to Primary Flash Reset location

0 = Device will reset to Auxiliary Flash Reset location

ICS<1:0> FICD Immediate ICD Communication Channel Select bits

11 = Communicate on PGEC1 and PGED1

10 = Communicate on PGEC2 and PGED2

01 = Communicate on PGEC3 and PGED3

00 = Reserved, do not use

TABLE 29-2: CONFIGURATION BITS DESCRIPTION (CONTINUED)

Bit Field Register RTSP Effect Description

Note 1: BOR should always be enabled for proper operation (BOREN = 1).

2: This register can only be modified when code protection and write protection are disabled for both the

General and Auxiliary Segments (APL = 1, AWRP = 1, APLK = 0, GSS = 1, GWRP = 1 and GSSK = 0).

 2009-2012 Microchip Technology Inc. DS70616G-page 481

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

29.2 On-Chip Voltage Regulator

All of the dsPIC33EPXXX(GP/MC/MU)806/810/814

and PIC24EPXXX(GP/GU)810/814 devices power

their core digital logic at a nominal 1.8V. This can create

a conflict for designs that are required to operate at a

higher typical voltage, such as 3.3V. To simplify system

design, all devices in the dsPIC33EPXXX(GP/MC/

MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

family incorporate an on-chip regulator that allows the

device to run its core logic from VDD.

The regulator provides power to the core from the other

VDD pins. A low-ESR (less than 1 Ohms) capacitor

(such as tantalum or ceramic) must be connected to the

VCAP pin (Figure 29-1). This helps to maintain the

stability of the regulator. The recommended value for

the filter capacitor is provided in Table 32-13 located in

Section 32.0 “Electrical Characteristics”.

FIGURE 29-1: CONNECTIONS FOR THE

ON-CHIP VOLTAGE

REGULATOR(1,2,3)

29.3 Brown-out Reset (BOR)

The Brown-out Reset module is based on an internal

voltage reference circuit that monitors the regulated

supply voltage, VCAP. The main purpose of the BOR

module is to generate a device Reset when a brown-

out condition occurs. Brown-out conditions are

generally caused by glitches on the AC mains (for

example, missing portions of the AC cycle waveform

due to bad power transmission lines, or voltage sags

due to excessive current draw when a large inductive

load is turned on).

A BOR generates a Reset pulse, which resets the

device. The BOR selects the clock source based on the

device Configuration bit values (FNOSC<2:0> and

POSCMD<1:0>).

If an oscillator mode is selected, the BOR activates the

Oscillator Start-up Timer (OST). The system clock is

held until OST expires. If the PLL is used, the clock is

held until the LOCK bit (OSCCON<5>) is ‘1’.

Concurrently, the Power-up Timer (PWRT) Time-out

(TPWRT) is applied before the internal Reset is

released. If TPWRT = 0 and a crystal oscillator is

being used, then a nominal delay of TFSCM is

applied. The total delay in this case is TFSCM. Refer

to Parameter SY35 in Table 32-22 of Section 32.0

“Electrical Characteristics” for specific TFSCM

values.

The BOR Status bit (RCON<1>) is set to indicate that a

BOR has occurred. The BOR circuit, continues to oper-

ate while in Sleep or Idle modes and resets the device

should VDD fall below the BOR threshold voltage.

Note: It is important for the low-ESR capacitor to

be placed as close as possible to the VCAP

pin.

Note 1: These are typical operating voltages. Refer

to Table 32-13 located in Section 32.1

“DC Characteristics” for the full operating

ranges of VDD and VCAP.

2: It is important for the low-ESR capacitor to

be placed as close as possible to the VCAP

pin.

3: Typical VCAP pin voltage is 1.8V when

VDD VDDMIN.

VDD

VCAP

VSS

dsPIC33E/PIC24E

CEFC

3.3V

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 482  2009-2012 Microchip Technology Inc.

29.4 Watchdog Timer (WDT)

For dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices, the WDT is

driven by the LPRC Oscillator. When the WDT is

enabled, the clock source is also enabled.

29.4.1 PRESCALER/POSTSCALER

The nominal WDT clock source from LPRC is 32 kHz.

This feeds a prescaler that can be configured for either

5-bit (divide-by-32) or 7-bit (divide-by-128) operation.

The prescaler is set by the WDTPRE Configuration bit.

With a 32 kHz input, the prescaler yields a nominal

WDT Time-out (TWDT) period of 1 ms in 5-bit mode or

4 ms in 7-bit mode.

A variable postscaler divides down the WDT prescaler

output and allows for a wide range of time-out periods.

The postscaler is controlled by the WDTPOST<3:0>

Configuration bits (FWDT<3:0>), which allow the selec-

tion of 16 settings, from 1:1 to 1:32,768. Using the

prescaler and postscaler, time-out periods ranging from

1 ms to 131 seconds can be achieved.

The WDT, prescaler and postscaler are reset:

• On any device Reset

• On the completion of a clock switch, whether

invoked by software (i.e., setting the OSWEN bit

after changing the NOSC bits) or by hardware

(i.e., Fail-Safe Clock Monitor)

• When a PWRSAV instruction is executed

(i.e., Sleep or Idle mode is entered)

• When the device exits Sleep or Idle mode to

resume normal operation

•By a CLRWDT instruction during normal execution

29.4.2 SLEEP AND IDLE MODES

If the WDT is enabled, it continues to run during Sleep or

Idle modes. When the WDT time-out occurs, the device

wakes the device and code execution continues from

where the PWRSAV instruction was executed. The corre-

sponding SLEEP or IDLE bits (RCON<3,2>) need to be

cleared in software after the device wakes up.

29.4.3 ENABLING WDT

The WDT is enabled or disabled by the FWDTEN

Configuration bit in the FWDT Configuration register.

When the FWDTEN Configuration bit is set, the WDT is

always enabled.

The WDT can be optionally controlled in software

when the FWDTEN Configuration bit has been

programmed to ‘0’. The WDT is enabled in software

by setting the SWDTEN control bit (RCON<5>). The

SWDTEN control bit is cleared on any device Reset.

The software WDT option allows the user application

to enable the WDT for critical code segments and

disable the WDT during non-critical segments for

maximum power savings.

The WDT flag bit, WDTO (RCON<4>), is not automatically

cleared following a WDT time-out. To detect subsequent

WDT events, the flag must be cleared in software.

FIGURE 29-2: WDT BLOCK DIAGRAM

Note: The CLRWDT and PWRSAV instructions

clear the prescaler and postscaler counts

when executed.

Note: If the WINDIS bit (FWDT<6>) is cleared,

the CLRWDT instruction should be executed

by the application software only during the

last 1/4 of the WDT period. This CLRWDT

instruction window can be determined by

using a timer. If a CLRWDT instruction is

executed before this window, a WDT Reset

occurs.

WDTPRE WDTPOST<3:0>

Watchdog Timer

Prescaler

(divide-by-N1)

Postscaler

(divide-by-N2)

Sleep/Idle

WDT

WDT Window Select

WINDIS

WDT

CLRWDT Instruction

SWDTEN

FWDTEN

LPRC Clock

RS RS

Wake-up

Reset

All Device Resets

Transition to New Clock Source

Exit Sleep or Idle Mode

PWRSAV

Instruction

CLRWDT

Instruction

 2009-2012 Microchip Technology Inc. DS70616G-page 483

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

29.5 JTAG Interface

dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices implement a

JTAG interface, which supports boundary scan device

testing. Detailed information on this interface is

provided in future revisions of the document.

29.6 In-Circuit Serial Programming

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices can be serially

programmed while in the end application circuit. This is

done with two lines for clock and data, and three other

lines for power, ground and the programming

sequence. Serial programming allows customers to

manufacture boards with unprogrammed devices and

then program the digital signal controller just before

shipping the product. Serial programming also allows

the most recent firmware or a custom firmware to be

programmed. Refer to the “dsPIC33E/PIC24E Flash

Programming Specification” (DS70619) for details

about In-Circuit Serial Programming (ICSP).

Any of the three pairs of programming clock/data pins

can be used:

• PGEC1 and PGED1

• PGEC2 and PGED2

• PGEC3 and PGED3

29.7 In-Circuit Debugger

When MPLAB® ICD 3 or REAL ICE™ is selected as a

debugger, the in-circuit debugging functionality is

enabled. This function allows simple debugging

functions when used with MPLAB IDE. Debugging

functionality is controlled through the PGECx (Emula-

tion/Debug Clock) and PGEDx (Emulation/Debug

Data) pin functions.

Any of the three pairs of debugging clock/data pins can

be used:

• PGEC1 and PGED1

• PGEC2 and PGED2

• PGEC3 and PGED3

To use the in-circuit debugger function of the device,

the design must implement ICSP connections to

MCLR, VDD, VSS and the PGECx/PGEDx pin pair. In

addition, when the feature is enabled, some of the

resources are not available for general use. These

resources include the first 80 bytes of data RAM and

two I/O pins.

29.8 Code Protection and

CodeGuard™ Security

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices offer basic

implementation of CodeGuard Security that supports

only General Segment (GS) security. This feature helps

protect individual Intellectual Property in collaborative

system designs.

When coupled with software encryption libraries,

CodeGuard Security can be used to securely update

Flash even when multiple IPs reside on the single chip.

The code protection features vary depending on the

actual dsPIC33E implemented. The following sections

provide an overview of these features.

The dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices do not support

Boot Segment (BS), Secure Segment (SS) and RAM

protection.

Note: Refer to Section 24. “Programming

and Diagnostics” (DS70608) of the

“dsPIC33E/PIC24E Family Reference

Manual” for further information on usage,

configuration and operation of the JTAG

interface.

Note: Refer to Section 23. “CodeGuard™

Security” (DS70634) of the “dsPIC33E/

PIC24E Family Reference Manual” for

further information on usage, configuration

and operation of CodeGuard Security.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 484  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 485

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

30.0 INSTRUCTION SET SUMMARY

The dsPIC33EP instruction set is almost identical to

that of the dsPIC30F and dsPIC33F. The PIC24EP

instruction set is almost identical to that of the PIC24F

and PIC24H.

Most instructions are a single program memory word

(24 bits). Only three instructions require two program

memory locations.

Each single-word instruction is a 24-bit word, divided

into an 8-bit opcode, which specifies the instruction

type and one or more operands, which further specify

the operation of the instruction.

The instruction set is highly orthogonal and is grouped

into five basic categories:

• Word or byte-oriented operations

• Bit-oriented operations

• Literal operations

• DSP operations

• Control operations

Table 30-1 lists the general symbols used in describing

the instructions.

The dsPIC33E instruction set summary in Ta b l e 3 0 - 2

lists all the instructions, along with the status flags

affected by each instruction.

Most word or byte-oriented W register instructions

(including barrel shift instructions) have three

operands:

• The first source operand, which is typically a

• The second source operand, which is typically a

• The destination of the result, which is typically a

However, word or byte-oriented file register instructions

have two operands:

• The file register specified by the value ‘f’

• The destination, which could be either the file

‘WREG’

Most bit-oriented instructions (including simple rotate/

shift instructions) have two operands:

• The W register (with or without an address

modifier) or file register (specified by the value of

‘Ws’ or ‘f’)

• The bit in the W register or file register (specified

by a literal value or indirectly by the contents of

The literal instructions that involve data movement can

use some of the following operands:

• A literal value to be loaded into a W register or file

• The W register or file register where the literal

value is to be loaded (specified by ‘Wb’ or ‘f’)

However, literal instructions that involve arithmetic or

logical operations use some of the following operands:

• The first source operand, which is a register ‘Wb’

without any address modifier

• The second source operand, which is a literal

value

• The destination of the result (only if not the same

as the first source operand), which is typically a

The MAC class of DSP instructions can use some of the

following operands:

• The accumulator (A or B) to be used (required

operand)

• The W registers to be used as the two operands

• The X and Y address space prefetch operations

• The X and Y address space prefetch destinations

• The accumulator write-back destination

The other DSP instructions do not involve any

multiplication and can include:

• The accumulator to be used (required)

• The source or destination operand (designated as

Wso or Wdo, respectively) with or without an

address modifier

• The amount of shift specified by a W register ‘Wn’

or a literal value

The control instructions can use some of the following

operands:

• A program memory address

• The mode of the table read and table write

instructions

Note: This data sheet summarizes the features of

the dsPIC33EPXXX(GP/MC/MU)806/810/

814 and PIC24EPXXX(GP/GU)810/814

families of devices. It is not intended to be a

comprehensive reference source. To

complement the information in this data

sheet, refer to the related section of the

“dsPIC33E/PIC24E Family Reference

Manual”, which is available from the

Microchip web site (www.microchip.com).

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 486  2009-2012 Microchip Technology Inc.

Most instructions are a single word. Certain double-word

instructions are designed to provide all the required

information in these 48 bits. In the second word, the

8 MSbs are ‘0’s. If this second word is executed as an

instruction (by itself), it executes as a NOP.

The double-word instructions execute in two instruction

cycles.

Most single-word instructions are executed in a single

instruction cycle, unless a conditional test is true, or the

Program Counter is changed as a result of the

instruction, or a PSV or table read is performed. In these

cases, the execution takes multiple instruction cycles

with the additional instruction cycle(s) executed as a

NOP. Certain instructions that involve skipping over the

subsequent instruction require either two or three cycles

if the skip is performed, depending on whether the

instruction being skipped is a single-word or two-word

instruction. Moreover, double-word moves require two

cycles.

Note: For more details on the instruction set,

refer to the “16-bit MCU and DSC

Programmer’s Reference Manual”

(DS70157).

TABLE 30-1: SYMBOLS USED IN OPCODE DESCRIPTIONS

Field Description

#text Means literal defined by “text”

(text) Means “content of text”

[text] Means “the location addressed by text”

{ } Optional field or operation

a  {b, c, d} a is selected from the set of values b, c, d

<n:m> Register bit field

.b Byte mode selection

.d Double-Word mode selection

.S Shadow register select

.w Word mode selection (default)

Acc One of two accumulators {A, B}

AWB Accumulator Write-Back Destination Address register {W13, [W13]+ = 2}

bit4 4-bit bit selection field (used in word addressed instructions) {0...15}

C, DC, N, OV, Z MCU Status bits: Carry, Digit Carry, Negative, Overflow, Sticky Zero

Expr Absolute address, label or expression (resolved by the linker)

f File register address {0x0000...0x1FFF}

lit1 1-bit unsigned literal {0,1}

lit4 4-bit unsigned literal {0...15}

lit5 5-bit unsigned literal {0...31}

lit8 8-bit unsigned literal {0...255}

lit10 10-bit unsigned literal {0...255} for Byte mode, {0:1023} for Word mode

lit14 14-bit unsigned literal {0...16384}

lit16 16-bit unsigned literal {0...65535}

lit23 23-bit unsigned literal {0...8388608}; LSb must be ‘0’

None Field does not require an entry, can be blank

OA, OB, SA, SB DSP Status bits: ACCA Overflow, ACCB Overflow, ACCA Saturate, ACCB Saturate

PC Program Counter

Slit10 10-bit signed literal {-512...511}

Slit16 16-bit signed literal {-32768...32767}

Slit6 6-bit signed literal {-16...16}

Wb Base W register {W0...W15}

Wd Destination W register { Wd, [Wd], [Wd++], [Wd--], [++Wd], [--Wd] }

Wdo Destination W register 

{ Wnd, [Wnd], [Wnd++], [Wnd--], [++Wnd], [--Wnd], [Wnd+Wb] }

Wm,Wn Dividend, Divisor Working register pair (Direct Addressing)

 2009-2012 Microchip Technology Inc. DS70616G-page 487

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Wm*Wm Multiplicand and Multiplier working register pair for Square instructions 

{W4 * W4,W5 * W5,W6 * W6,W7 * W7}

Wm*Wn Multiplicand and Multiplier working register pair for DSP instructions 

{W4 * W5,W4 * W6,W4 * W7,W5 * W6,W5 * W7,W6 * W7}

Wn One of 16 working registers {W0...W15}

Wnd One of 16 destination working registers {W0...W15}

Wns One of 16 source working registers {W0...W15}

WREG W0 (working register used in file register instructions)

Ws Source W register { Ws, [Ws], [Ws++], [Ws--], [++Ws], [--Ws] }

Wso Source W register 

{ Wns, [Wns], [Wns++], [Wns--], [++Wns], [--Wns], [Wns+Wb] }

Wx X Data Space Prefetch Address register for DSP instructions

{[W8] + = 6, [W8] + = 4, [W8] + = 2, [W8], [W8] - = 6, [W8] - = 4, [W8] - = 2,

[W9] + = 6, [W9] + = 4, [W9] + = 2, [W9], [W9] - = 6, [W9] - = 4, [W9] - = 2,

[W9 + W12], none}

Wxd X Data Space Prefetch Destination register for DSP instructions {W4...W7}

Wy Y Data Space Prefetch Address register for DSP instructions

{[W10] + = 6, [W10] + = 4, [W10] + = 2, [W10], [W10] - = 6, [W10] - = 4, [W10] - = 2,

[W11] + = 6, [W11] + = 4, [W11] + = 2, [W11], [W11] - = 6, [W11] - = 4, [W11] - = 2,

[W11 + W12], none}

Wyd Y Data Space Prefetch Destination register for DSP instructions {W4...W7}

TABLE 30-1: SYMBOLS USED IN OPCODE DESCRIPTIONS (CONTINUED)

Field Description

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 488  2009-2012 Microchip Technology Inc.

TABLE 30-2: INSTRUCTION SET OVERVIEW

Base

Instr

Assembly

Mnemonic Assembly Syntax Description # of

Words

# of

Cycles(2)Status Flags

Affected

1ADD ADD Acc(1)Add Accumulators 1 1 OA,OB,SA,SB

ADD f f = f + WREG 1 1 C,DC,N,OV,Z

ADD f,WREG WREG = f + WREG 1 1 C,DC,N,OV,Z

ADD #lit10,Wn Wd = lit10 + Wd 1 1 C,DC,N,OV,Z

ADD Wb,Ws,Wd Wd = Wb + Ws 1 1 C,DC,N,OV,Z

ADD Wb,#lit5,Wd Wd = Wb + lit5 1 1 C,DC,N,OV,Z

ADD Wso,#Slit4,Acc 16-bit Signed Add to Accumulator 1 1 OA,OB,SA,SB

2ADDC ADDC f f = f + WREG + (C) 1 1 C,DC,N,OV,Z

ADDC f,WREG WREG = f + WREG + (C) 1 1 C,DC,N,OV,Z

ADDC #lit10,Wn Wd = lit10 + Wd + (C) 1 1 C,DC,N,OV,Z

ADDC Wb,Ws,Wd Wd = Wb + Ws + (C) 1 1 C,DC,N,OV,Z

ADDC Wb,#lit5,Wd Wd = Wb + lit5 + (C) 1 1 C,DC,N,OV,Z

3AND AND f f = f .AND. WREG 1 1 N,Z

AND f,WREG WREG = f .AND. WREG 1 1 N,Z

AND #lit10,Wn Wd = lit10 .AND. Wd 1 1 N,Z

AND Wb,Ws,Wd Wd = Wb .AND. Ws 1 1 N,Z

AND Wb,#lit5,Wd Wd = Wb .AND. lit5 1 1 N,Z

4ASR ASR f f = Arithmetic Right Shift f 1 1 C,N,OV,Z

ASR f,WREG WREG = Arithmetic Right Shift f 1 1 C,N,OV,Z

ASR Ws,Wd Wd = Arithmetic Right Shift Ws 1 1 C,N,OV,Z

ASR Wb,Wns,Wnd Wnd = Arithmetic Right Shift Wb by Wns 1 1 N,Z

ASR Wb,#lit5,Wnd Wnd = Arithmetic Right Shift Wb by lit5 1 1 N,Z

5BCLR BCLR f,#bit4 Bit Clear f 1 1 None

BCLR Ws,#bit4 Bit Clear Ws 1 1 None

6BRA BRA C,Expr Branch if Carry 1 1 (4) None

BRA GE,Expr Branch if greater than or equal 1 1 (4) None

BRA GEU,Expr Branch if unsigned greater than or equal 1 1 (4) None

BRA GT,Expr Branch if greater than 1 1 (4) None

BRA GTU,Expr Branch if unsigned greater than 1 1 (4) None

BRA LE,Expr Branch if less than or equal 1 1 (4) None

BRA LEU,Expr Branch if unsigned less than or equal 1 1 (4) None

BRA LT,Expr Branch if less than 1 1 (4) None

BRA LTU,Expr Branch if unsigned less than 1 1 (4) None

BRA N,Expr Branch if Negative 1 1 (4) None

BRA NC,Expr Branch if Not Carry 1 1 (4) None

BRA NN,Expr Branch if Not Negative 1 1 (4) None

BRA NOV,Expr Branch if Not Overflow 1 1 (4) None

BRA NZ,Expr Branch if Not Zero 1 1 (4) None

BRA OA,Expr(1)Branch if Accumulator A overflow 1 1 (4) None

BRA OB,Expr(1)Branch if Accumulator B overflow 1 1 (4) None

BRA OV,Expr(1)Branch if Overflow 1 1 (4) None

BRA SA,Expr(1)Branch if Accumulator A saturated 1 1 (4) None

BRA SB,Expr(1)Branch if Accumulator B saturated 1 1 (4) None

BRA Expr Branch Unconditionally 1 4 None

BRA Z,Expr Branch if Zero 1 1 (4) None

BRA Wn Computed Branch 1 4 None

7BSET BSET f,#bit4 Bit Set f 1 1 None

BSET Ws,#bit4 Bit Set Ws 1 1 None

Note 1: This instruction is available in dsPIC33EPXXX(GP/MC/MU)806/810/814 devices only.

2: Read and Read-Modify-Write (e.g., bit operations and logical operations) on non-CPU SFRs incur an additional instruction cycle.

 2009-2012 Microchip Technology Inc. DS70616G-page 489

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

8BSW BSW.C Ws,Wb Write C bit to Ws<Wb> 1 1 None

BSW.Z Ws,Wb Write Z bit to Ws<Wb> 1 1 None

9BTG BTG f,#bit4 Bit Toggle f 1 1 None

BTG Ws,#bit4 Bit Toggle Ws 1 1 None

10 BTSC BTSC f,#bit4 Bit Test f, Skip if Clear 1 1

(2 or 3)

None

BTSC Ws,#bit4 Bit Test Ws, Skip if Clear 1 1

(2 or 3)

None

11 BTSS BTSS f,#bit4 Bit Test f, Skip if Set 1 1

(2 or 3)

None

BTSS Ws,#bit4 Bit Test Ws, Skip if Set 1 1

(2 or 3)

None

12 BTST BTST f,#bit4 Bit Test f 1 1 Z

BTST.C Ws,#bit4 Bit Test Ws to C 1 1 C

BTST.Z Ws,#bit4 Bit Test Ws to Z 1 1 Z

BTST.C Ws,Wb Bit Test Ws<Wb> to C 1 1 C

BTST.Z Ws,Wb Bit Test Ws<Wb> to Z 1 1 Z

13 BTSTS BTSTS f,#bit4 Bit Test then Set f 1 1 Z

BTSTS.C Ws,#bit4 Bit Test Ws to C, then Set 1 1 C

BTSTS.Z Ws,#bit4 Bit Test Ws to Z, then Set 1 1 Z

14 CALL CALL lit23 Call subroutine 2 4 SFA

CALL Wn Call indirect subroutine 1 4 SFA

CALL.L Wn Call indirect subroutine (long address) 1 4 SFA

15 CLR CLR f f = 0x0000 1 1 None

CLR WREG WREG = 0x0000 1 1 None

CLR Ws Ws = 0x0000 1 1 None

CLR Acc,Wx,Wxd,Wy,Wyd,AWB(1)Clear Accumulator 1 1 OA,OB,SA,SB

16 CLRWDT CLRWDT Clear Watchdog Timer 1 1 WDTO,Sleep

17 COM COM f f = f 11 N,Z

COM f,WREG WREG = f 11 N,Z

COM Ws,Wd Wd = Ws 11 N,Z

18 CP CP f Compare f with WREG 1 1 C,DC,N,OV,Z

CP Wb,#lit8 Compare Wb with lit8 1 1 C,DC,N,OV,Z

CP Wb,Ws Compare Wb with Ws (Wb – Ws) 1 1 C,DC,N,OV,Z

19 CP0 CP0 f Compare f with 0x0000 1 1 C,DC,N,OV,Z

CP0 Ws Compare Ws with 0x0000 1 1 C,DC,N,OV,Z

20 CPB CPB f Compare f with WREG, with Borrow 1 1 C,DC,N,OV,Z

CPB Wb,#lit8 Compare Wb with lit8, with Borrow 1 1 C,DC,N,OV,Z

CPB Wb,Ws Compare Wb with Ws, with Borrow

(Wb – Ws – C)

1 1 C,DC,N,OV,Z

21 CPSEQ CPSEQ Wb,Wn Compare Wb with Wn, skip if = 1 1

(2 or 3)

None

CPBEQ CPBEQ Wb,Wn,Expr Compare Wb with Wn, branch if = 1 1 (5) None

22 CPSGT CPSGT Wb,Wn Compare Wb with Wn, skip if > 1 1

(2 or 3)

None

CPBGT CPBGT Wb,Wn,Expr Compare Wb with Wn, branch if > 1 1 (5) None

23 CPSLT CPSLT Wb,Wn Compare Wb with Wn, skip if < 1 1

(2 or 3)

None

CPBLT CPBLT Wb,Wn,Expr Compare Wb with Wn, branch if < 1 1 (5) None

24 CPSNE CPSNE Wb,Wn Compare Wb with Wn, skip if 11

(2 or 3)

None

CPBNE CPBNE Wb,Wn,Expr Compare Wb with Wn, branch if 11 (5) None

TABLE 30-2: INSTRUCTION SET OVERVIEW (CONTINUED)

Base

Instr

Assembly

Mnemonic Assembly Syntax Description # of

Words

# of

Cycles(2)Status Flags

Affected

Note 1: This instruction is available in dsPIC33EPXXX(GP/MC/MU)806/810/814 devices only.

2: Read and Read-Modify-Write (e.g., bit operations and logical operations) on non-CPU SFRs incur an additional instruction cycle.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 490  2009-2012 Microchip Technology Inc.

25 DAW DAW Wn Wn = decimal adjust Wn 1 1 C

26 DEC DEC f f = f – 1 1 1 C,DC,N,OV,Z

DEC f,WREG WREG = f – 1 1 1 C,DC,N,OV,Z

DEC Ws,Wd Wd = Ws – 1 1 1 C,DC,N,OV,Z

27 DEC2 DEC2 f f = f – 2 1 1 C,DC,N,OV,Z

DEC2 f,WREG WREG = f – 2 1 1 C,DC,N,OV,Z

DEC2 Ws,Wd Wd = Ws – 2 1 1 C,DC,N,OV,Z

28 DISI DISI #lit14 Disable Interrupts for k instruction cycles 1 1 None

29 DIV DIV.S Wm,Wn Signed 16/16-bit Integer Divide 1 18 N,Z,C,OV

DIV.SD Wm,Wn Signed 32/16-bit Integer Divide 1 18 N,Z,C,OV

DIV.U Wm,Wn Unsigned 16/16-bit Integer Divide 1 18 N,Z,C,OV

DIV.UD Wm,Wn Unsigned 32/16-bit Integer Divide 1 18 N,Z,C,OV

30 DIVF DIVF Wm,Wn(1)Signed 16/16-bit Fractional Divide 1 18 N,Z,C,OV

31 DO DO #lit15,Expr(1)Do code to PC + Expr, lit15 + 1 times 2 2 None

DO Wn,Expr(1)Do code to PC + Expr, (Wn) + 1 times 2 2 None

32 ED ED Wm*Wm,Acc,Wx,Wy,Wxd(1)Euclidean Distance (no accumulate) 1 1 OA,OB,OAB,

SA,SB,SAB

33 EDAC EDAC Wm*Wm,Acc,Wx,Wy,Wxd(1)Euclidean Distance 1 1 OA,OB,OAB,

SA,SB,SAB

34 EXCH EXCH Wns,Wnd Swap Wns with Wnd 1 1 None

35 FBCL FBCL Ws,Wnd Find Bit Change from Left (MSb) Side 1 1 C

36 FF1L FF1L Ws,Wnd Find First One from Left (MSb) Side 1 1 C

37 FF1R FF1R Ws,Wnd Find First One from Right (LSb) Side 1 1 C

38 GOTO GOTO Expr Go to address 2 4 None

GOTO Wn Go to indirect 1 4 None

GOTO.L Wn Go to indirect (long address) 1 4 None

39 INC INC f f = f + 1 1 1 C,DC,N,OV,Z

INC f,WREG WREG = f + 1 1 1 C,DC,N,OV,Z

INC Ws,Wd Wd = Ws + 1 1 1 C,DC,N,OV,Z

40 INC2 INC2 f f = f + 2 1 1 C,DC,N,OV,Z

INC2 f,WREG WREG = f + 2 1 1 C,DC,N,OV,Z

INC2 Ws,Wd Wd = Ws + 2 1 1 C,DC,N,OV,Z

41 IOR IOR f f = f .IOR. WREG 1 1 N,Z

IOR f,WREG WREG = f .IOR. WREG 1 1 N,Z

IOR #lit10,Wn Wd = lit10 .IOR. Wd 1 1 N,Z

IOR Wb,Ws,Wd Wd = Wb .IOR. Ws 1 1 N,Z

IOR Wb,#lit5,Wd Wd = Wb .IOR. lit5 1 1 N,Z

42 LAC LAC Wso,#Slit4,Acc Load Accumulator 1 1 OA,OB,OAB,

SA,SB,SAB

43 LNK LNK #lit14 Link Frame Pointer 1 1 SFA

44 LSR LSR f f = Logical Right Shift f 1 1 C,N,OV,Z

LSR f,WREG WREG = Logical Right Shift f 1 1 C,N,OV,Z

LSR Ws,Wd Wd = Logical Right Shift Ws 1 1 C,N,OV,Z

LSR Wb,Wns,Wnd Wnd = Logical Right Shift Wb by Wns 1 1 N,Z

LSR Wb,#lit5,Wnd Wnd = Logical Right Shift Wb by lit5 1 1 N,Z

45 MAC MAC Wm*Wn,Acc,Wx,Wxd,Wy,Wyd,AWB(1)Multiply and Accumulate 1 1 OA,OB,OAB,

SA,SB,SAB

MAC Wm*Wm,Acc,Wx,Wxd,Wy,Wyd(1)Square and Accumulate 1 1 OA,OB,OAB,

SA,SB,SAB

TABLE 30-2: INSTRUCTION SET OVERVIEW (CONTINUED)

Base

Instr

Assembly

Mnemonic Assembly Syntax Description # of

Words

# of

Cycles(2)Status Flags

Affected

Note 1: This instruction is available in dsPIC33EPXXX(GP/MC/MU)806/810/814 devices only.

2: Read and Read-Modify-Write (e.g., bit operations and logical operations) on non-CPU SFRs incur an additional instruction cycle.

 2009-2012 Microchip Technology Inc. DS70616G-page 491

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

46 MOV MOV f,Wn Move f to Wn 1 1 None

MOV f Move f to f 1 1 None

MOV f,WREG Move f to WREG 1 1 None

MOV #lit16,Wn Move 16-bit literal to Wn 1 1 None

MOV.b #lit8,Wn Move 8-bit literal to Wn 1 1 None

MOV Wn,f Move Wn to f 1 1 None

MOV Wso,Wdo Move Ws to Wd 1 1 None

MOV WREG,f Move WREG to f 1 1 None

MOV.D Wns,Wd Move Double from W(ns):W(ns + 1) to Wd 1 2 None

MOV.D Ws,Wnd Move Double from Ws to W(nd + 1):W(nd) 1 2 None

47 MOVPAG MOVPAG #lit10,DSRPAG Move 10-bit literal to DSRPAG 1 1 None

MOVPAG #lit9,DSWPAG Move 9-bit literal to DSWPAG 1 1 None

MOVPAG #lit8,TBLPAG Move 8-bit literal to TBLPAG 1 1 None

MOVPAGW Ws, DSRPAG Move Ws<9:0> to DSRPAG 1 1 None

MOVPAGW Ws, DSWPAG Move Ws<8:0> to DSWPAG 1 1 None

MOVPAGW Ws, TBLPAG Move Ws<7:0> to TBLPAG 1 1 None

48 MOVSAC MOVSAC Acc,Wx,Wxd,Wy,Wyd,AWB(1)Prefetch and store accumulator 1 1 None

49 MPY MPY Wm*Wn,Acc,Wx,Wxd,Wy,Wyd(1)Multiply Wm by Wn to Accumulator 1 1 OA,OB,OAB,

SA,SB,SAB

MPY Wm*Wm,Acc,Wx,Wxd,Wy,Wyd(1)Square Wm to Accumulator 1 1 OA,OB,OAB,

SA,SB,SAB

50 MPY.N MPY.N Wm*Wn,Acc,Wx,Wxd,Wy,Wyd(1)-(Multiply Wm by Wn) to Accumulator 1 1 None

51 MSC MSC Wm*Wm,Acc,Wx,Wxd,Wy,Wyd,AWB(1)Multiply and Subtract from Accumulator 1 1 OA,OB,OAB,

SA,SB,SAB

52 MUL MUL.SS Wb,Ws,Wnd {Wnd + 1, Wnd} = signed(Wb) *

signed(Ws)

11 None

MUL.SS Wb,Ws,Acc(1)Accumulator = signed(Wb) * signed(Ws) 1 1 None

MUL.SU Wb,Ws,Wnd {Wnd + 1, Wnd} = signed(Wb) *

unsigned(Ws)

11 None

MUL.SU Wb,Ws,Acc(1)Accumulator = signed(Wb) *

unsigned(Ws)

11 None

MUL.SU Wb,#lit5,Acc(1)Accumulator = signed(Wb) *

unsigned(lit5)

11 None

MUL.US Wb,Ws,Wnd {Wnd + 1, Wnd} = unsigned(Wb) *

signed(Ws)

11 None

MUL.US Wb,Ws,Acc(1)Accumulator = unsigned(Wb) *

signed(Ws)

11 None

MUL.UU Wb,Ws,Wnd {Wnd + 1, Wnd} = unsigned(Wb) *

unsigned(Ws)

11 None

MUL.UU Wb,#lit5,Acc(1)Accumulator = unsigned(Wb) *

unsigned(lit5)

11 None

MUL.UU Wb,Ws,Acc(1)Accumulator = unsigned(Wb) *

unsigned(Ws)

11 None

MULW.SS Wb,Ws,Wnd Wnd = signed(Wb) * signed(Ws) 1 1 None

MULW.SU Wb,Ws,Wnd Wnd = signed(Wb) * unsigned(Ws) 1 1 None

MULW.US Wb,Ws,Wnd Wnd = unsigned(Wb) * signed(Ws) 1 1 None

MULW.UU Wb,Ws,Wnd Wnd = unsigned(Wb) * unsigned(Ws) 1 1 None

MUL.SU Wb,#lit5,Wnd {Wnd + 1, Wnd} = signed(Wb) *

unsigned(lit5)

11 None

MUL.SU Wb,#lit5,Wnd Wnd = signed(Wb) * unsigned(lit5) 1 1 None

MUL.UU Wb,#lit5,Wnd {Wnd + 1, Wnd} = unsigned(Wb) *

unsigned(lit5)

11 None

MUL.UU Wb,#lit5,Wnd Wnd = unsigned(Wb) * unsigned(lit5) 1 1 None

MUL f W3:W2 = f * WREG 1 1 None

TABLE 30-2: INSTRUCTION SET OVERVIEW (CONTINUED)

Base

Instr

Assembly

Mnemonic Assembly Syntax Description # of

Words

# of

Cycles(2)Status Flags

Affected

Note 1: This instruction is available in dsPIC33EPXXX(GP/MC/MU)806/810/814 devices only.

2: Read and Read-Modify-Write (e.g., bit operations and logical operations) on non-CPU SFRs incur an additional instruction cycle.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 492  2009-2012 Microchip Technology Inc.

53 NEG NEG Acc(1)Negate Accumulator 1 1 OA,OB,OAB,

SA,SB,SAB

NEG f f = f + 1 1 1 C,DC,N,OV,Z

NEG f,WREG WREG = f + 1 1 1 C,DC,N,OV,Z

NEG Ws,Wd Wd = Ws + 1 1 1 C,DC,N,OV,Z

54 NOP NOP No Operation 1 1 None

NOPR No Operation 1 1 None

55 POP POP f Pop f from Top-of-Stack (TOS) 1 1 None

POP Wdo Pop from Top-of-Stack (TOS) to Wdo 1 1 None

POP.D Wnd Pop from Top-of-Stack (TOS) to

W(nd):W(nd + 1)

12 None

POP.S Pop Shadow Registers 1 1 All

56 PUSH PUSH f Push f to Top-of-Stack (TOS) 1 1 None

PUSH Wso Push Wso to Top-of-Stack (TOS) 1 1 None

PUSH.D Wns Push W(ns):W(ns + 1) to Top-of-Stack

(TOS)

12 None

PUSH.S Push Shadow Registers 1 1 None

57 PWRSAV PWRSAV #lit1 Go into Sleep or Idle mode 1 1 WDTO,Sleep

58 RCALL RCALL Expr Relative Call 1 4 SFA

RCALL Wn Computed Call 1 4 SFA

59 REPEAT REPEAT #lit15 Repeat Next Instruction lit15 + 1 times 1 1 None

REPEAT Wn Repeat Next Instruction (Wn) + 1 times 1 1 None

60 RESET RESET Software device Reset 1 1 None

61 RETFIE RETFIE Return from interrupt 1 6 (5) SFA

62 RETLW RETLW #lit10,Wn Return with literal in Wn 1 6 (5) SFA

63 RETURN RETURN Return from Subroutine 1 6 (5) SFA

64 RLC RLC f f = Rotate Left through Carry f 1 1 C,N,Z

RLC f,WREG WREG = Rotate Left through Carry f 1 1 C,N,Z

RLC Ws,Wd Wd = Rotate Left through Carry Ws 1 1 C,N,Z

65 RLNC RLNC f f = Rotate Left (No Carry) f 1 1 N,Z

RLNC f,WREG WREG = Rotate Left (No Carry) f 1 1 N,Z

RLNC Ws,Wd Wd = Rotate Left (No Carry) Ws 1 1 N,Z

66 RRC RRC f f = Rotate Right through Carry f 1 1 C,N,Z

RRC f,WREG WREG = Rotate Right through Carry f 1 1 C,N,Z

RRC Ws,Wd Wd = Rotate Right through Carry Ws 1 1 C,N,Z

67 RRNC RRNC f f = Rotate Right (No Carry) f 1 1 N,Z

RRNC f,WREG WREG = Rotate Right (No Carry) f 1 1 N,Z

RRNC Ws,Wd Wd = Rotate Right (No Carry) Ws 1 1 N,Z

68 SAC SAC Acc,#Slit4,Wdo(1)Store Accumulator 1 1 None

SAC.R Acc,#Slit4,Wdo(1)Store Rounded Accumulator 1 1 None

69 SE SE Ws,Wnd Wnd = sign-extended Ws 1 1 C,N,Z

70 SETM SETM f f = 0xFFFF 1 1 None

SETM WREG WREG = 0xFFFF 1 1 None

SETM Ws Ws = 0xFFFF 1 1 None

71 SFTAC SFTAC Acc,Wn(1)Arithmetic Shift Accumulator by (Wn) 1 1 OA,OB,OAB,

SA,SB,SAB

SFTAC Acc,#Slit6(1)Arithmetic Shift Accumulator by Slit6 1 1 OA,OB,OAB,

SA,SB,SAB

TABLE 30-2: INSTRUCTION SET OVERVIEW (CONTINUED)

Base

Instr

Assembly

Mnemonic Assembly Syntax Description # of

Words

# of

Cycles(2)Status Flags

Affected

Note 1: This instruction is available in dsPIC33EPXXX(GP/MC/MU)806/810/814 devices only.

2: Read and Read-Modify-Write (e.g., bit operations and logical operations) on non-CPU SFRs incur an additional instruction cycle.

 2009-2012 Microchip Technology Inc. DS70616G-page 493

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

72 SL SL f f = Left Shift f 1 1 C,N,OV,Z

SL f,WREG WREG = Left Shift f 1 1 C,N,OV,Z

SL Ws,Wd Wd = Left Shift Ws 1 1 C,N,OV,Z

SL Wb,Wns,Wnd Wnd = Left Shift Wb by Wns 1 1 N,Z

SL Wb,#lit5,Wnd Wnd = Left Shift Wb by lit5 1 1 N,Z

73 SUB SUB Acc(1)Subtract Accumulators 1 1 OA,OB,OAB,

SA,SB,SAB

SUB f f = f – WREG 1 1 C,DC,N,OV,Z

SUB f,WREG WREG = f – WREG 1 1 C,DC,N,OV,Z

SUB #lit10,Wn Wn = Wn – lit10 1 1 C,DC,N,OV,Z

SUB Wb,Ws,Wd Wd = Wb – Ws 1 1 C,DC,N,OV,Z

SUB Wb,#lit5,Wd Wd = Wb – lit5 1 1 C,DC,N,OV,Z

74 SUBB SUBB f f = f – WREG – (C) 1 1 C,DC,N,OV,Z

SUBB f,WREG WREG = f – WREG – (C) 1 1 C,DC,N,OV,Z

SUBB #lit10,Wn Wn = Wn – lit10 – (C) 1 1 C,DC,N,OV,Z

SUBB Wb,Ws,Wd Wd = Wb – Ws – (C) 1 1 C,DC,N,OV,Z

SUBB Wb,#lit5,Wd Wd = Wb – lit5 – (C) 1 1 C,DC,N,OV,Z

75 SUBR SUBR f f = WREG – f 1 1 C,DC,N,OV,Z

SUBR f,WREG WREG = WREG – f 1 1 C,DC,N,OV,Z

SUBR Wb,Ws,Wd Wd = Ws – Wb 1 1 C,DC,N,OV,Z

SUBR Wb,#lit5,Wd Wd = lit5 – Wb 1 1 C,DC,N,OV,Z

76 SUBBR SUBBR f f = WREG – f – (C) 1 1 C,DC,N,OV,Z

SUBBR f,WREG WREG = WREG – f – (C) 1 1 C,DC,N,OV,Z

SUBBR Wb,Ws,Wd Wd = Ws – Wb – (C) 1 1 C,DC,N,OV,Z

SUBBR Wb,#lit5,Wd Wd = lit5 – Wb – (C) 1 1 C,DC,N,OV,Z

77 SWAP SWAP.b Wn Wn = nibble swap Wn 1 1 None

SWAP Wn Wn = byte swap Wn 1 1 None

78 TBLRDH TBLRDH Ws,Wd Read Prog<23:16> to Wd<7:0> 1 5 None

79 TBLRDL TBLRDL Ws,Wd Read Prog<15:0> to Wd 1 5 None

80 TBLWTH TBLWTH Ws,Wd Write Ws<7:0> to Prog<23:16> 1 2 None

81 TBLWTL TBLWTL Ws,Wd Write Ws to Prog<15:0> 1 2 None

82 ULNK ULNK Unlink Frame Pointer 1 1 SFA

83 XOR XOR f f = f .XOR. WREG 1 1 N,Z

XOR f,WREG WREG = f .XOR. WREG 1 1 N,Z

XOR #lit10,Wn Wd = lit10 .XOR. Wd 1 1 N,Z

XOR Wb,Ws,Wd Wd = Wb .XOR. Ws 1 1 N,Z

XOR Wb,#lit5,Wd Wd = Wb .XOR. lit5 1 1 N,Z

84 ZE ZE Ws,Wnd Wnd = Zero-Extend Ws 1 1 C,Z,N

TABLE 30-2: INSTRUCTION SET OVERVIEW (CONTINUED)

Base

Instr

Assembly

Mnemonic Assembly Syntax Description # of

Words

# of

Cycles(2)Status Flags

Affected

Note 1: This instruction is available in dsPIC33EPXXX(GP/MC/MU)806/810/814 devices only.

2: Read and Read-Modify-Write (e.g., bit operations and logical operations) on non-CPU SFRs incur an additional instruction cycle.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 494  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 495

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

31.0 DEVELOPMENT SUPPORT

The PIC® microcontrollers and dsPIC® digital signal

controllers are supported with a full range of software

and hardware development tools:

• Integrated Development Environment

- MPLAB® IDE Software

• Compilers/Assemblers/Linkers

- MPLAB C Compiler for Various Device

Families

- HI-TECH C® for Various Device Families

- MPASMTM Assembler

-MPLINK

TM Object Linker/

MPLIBTM Object Librarian

- MPLAB Assembler/Linker/Librarian for

Various Device Families

• Simulators

- MPLAB SIM Software Simulator

• Emulators

- MPLAB REAL ICE™ In-Circuit Emulator

• In-Circuit Debuggers

- MPLAB ICD 3

- PICkit™ 3 Debug Express

• Device Programmers

- PICkit™ 2 Programmer

- MPLAB PM3 Device Programmer

• Low-Cost Demonstration/Development Boards,

Evaluation Kits and Starter Kits

31.1 MPLAB Integrated Development

Environment Software

The MPLAB IDE software brings an ease of software

development previously unseen in the 8/16/32-bit

microcontroller market. The MPLAB IDE is a Windows®

operating system-based application that contains:

• A single graphical interface to all debugging tools

- Simulator

- Programmer (sold separately)

- In-Circuit Emulator (sold separately)

- In-Circuit Debugger (sold separately)

• A full-featured editor with color-coded context

• A multiple project manager

• Customizable data windows with direct edit of

contents

• High-level source code debugging

• Mouse over variable inspection

• Drag and drop variables from source to watch

windows

• Extensive on-line help

• Integration of select third party tools, such as

IAR C Compilers

The MPLAB IDE allows you to:

• Edit your source files (either C or assembly)

• One-touch compile or assemble, and download to

emulator and simulator tools (automatically

updates all project information)

• Debug using:

- Source files (C or assembly)

- Mixed C and assembly

- Machine code

MPLAB IDE supports multiple debugging tools in a

single development paradigm, from the cost-effective

simulators, through low-cost in-circuit debuggers, to

full-featured emulators. This eliminates the learning

curve when upgrading to tools with increased flexibility

and power.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 496  2009-2012 Microchip Technology Inc.

31.2 MPLAB C Compilers for Various

Device Families

The MPLAB C Compiler code development systems

are complete ANSI C compilers for Microchip’s PIC18,

PIC24 and PIC32 families of microcontrollers and the

dsPIC30 and dsPIC33 families of digital signal control-

lers. These compilers provide powerful integration

capabilities, superior code optimization and ease of

use.

For easy source level debugging, the compilers provide

symbol information that is optimized to the MPLAB IDE

debugger.

31.3 HI-TECH C for Various Device

Families

The HI-TECH C Compiler code development systems

are complete ANSI C compilers for Microchip’s PIC

family of microcontrollers and the dsPIC family of digital

signal controllers. These compilers provide powerful

integration capabilities, omniscient code generation

and ease of use.

For easy source level debugging, the compilers provide

symbol information that is optimized to the MPLAB IDE

debugger.

The compilers include a macro assembler, linker, pre-

processor, and one-step driver, and can run on multiple

platforms.

31.4 MPASM Assembler

The MPASM Assembler is a full-featured, universal

macro assembler for PIC10/12/16/18 MCUs.

The MPASM Assembler generates relocatable object

files for the MPLINK Object Linker, Intel® standard HEX

files, MAP files to detail memory usage and symbol

reference, absolute LST files that contain source lines

and generated machine code and COFF files for

debugging.

The MPASM Assembler features include:

• Integration into MPLAB IDE projects

• User-defined macros to streamline

assembly code

• Conditional assembly for multi-purpose

source files

• Directives that allow complete control over the

assembly process

31.5 MPLINK Object Linker/

MPLIB Object Librarian

The MPLINK Object Linker combines relocatable

objects created by the MPASM Assembler and the

MPLAB C18 C Compiler. It can link relocatable objects

from precompiled libraries, using directives from a

linker script.

The MPLIB Object Librarian manages the creation and

modification of library files of precompiled code. When

a routine from a library is called from a source file, only

the modules that contain that routine will be linked in

with the application. This allows large libraries to be

used efficiently in many different applications.

The object linker/library features include:

• Efficient linking of single libraries instead of many

smaller files

• Enhanced code maintainability by grouping

related modules together

• Flexible creation of libraries with easy module

listing, replacement, deletion and extraction

31.6 MPLAB Assembler, Linker and

Librarian for Various Device

Families

MPLAB Assembler produces relocatable machine

code from symbolic assembly language for PIC24,

PIC32 and dsPIC devices. MPLAB C Compiler uses

the assembler to produce its object file. The assembler

generates relocatable object files that can then be

archived or linked with other relocatable object files and

archives to create an executable file. Notable features

of the assembler include:

• Support for the entire device instruction set

• Support for fixed-point and floating-point data

• Command line interface

• Rich directive set

• Flexible macro language

• MPLAB IDE compatibility

 2009-2012 Microchip Technology Inc. DS70616G-page 497

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

31.7 MPLAB SIM Software Simulator

The MPLAB SIM Software Simulator allows code

development in a PC-hosted environment by simulat-

ing the PIC MCUs and dsPIC® DSCs on an instruction

level. On any given instruction, the data areas can be

examined or modified and stimuli can be applied from

a comprehensive stimulus controller. Registers can be

logged to files for further run-time analysis. The trace

buffer and logic analyzer display extend the power of

the simulator to record and track program execution,

actions on I/O, most peripherals and internal registers.

The MPLAB SIM Software Simulator fully supports

symbolic debugging using the MPLAB C Compilers,

and the MPASM and MPLAB Assemblers. The soft-

ware simulator offers the flexibility to develop and

debug code outside of the hardware laboratory envi-

ronment, making it an excellent, economical software

development tool.

31.8 MPLAB REAL ICE In-Circuit

Emulator System

MPLAB REAL ICE In-Circuit Emulator System is

Microchip’s next generation high-speed emulator for

Microchip Flash DSC and MCU devices. It debugs and

programs PIC® Flash MCUs and dsPIC® Flash DSCs

with the easy-to-use, powerful graphical user interface of

the MPLAB Integrated Development Environment (IDE),

included with each kit.

The emulator is connected to the design engineer’s PC

using a high-speed USB 2.0 interface and is connected

to the target with either a connector compatible with in-

circuit debugger systems (RJ11) or with the new high-

speed, noise tolerant, Low-Voltage Differential Signal

(LVDS) interconnection (CAT5).

The emulator is field upgradable through future firmware

downloads in MPLAB IDE. In upcoming releases of

MPLAB IDE, new devices will be supported, and new

features will be added. MPLAB REAL ICE offers

significant advantages over competitive emulators

including low-cost, full-speed emulation, run-time

variable watches, trace analysis, complex breakpoints, a

ruggedized probe interface and long (up to three meters)

interconnection cables.

31.9 MPLAB ICD 3 In-Circuit Debugger

System

MPLAB ICD 3 In-Circuit Debugger System is Micro-

chip's most cost effective high-speed hardware

debugger/programmer for Microchip Flash Digital Sig-

nal Controller (DSC) and microcontroller (MCU)

devices. It debugs and programs PIC® Flash microcon-

trollers and dsPIC® DSCs with the powerful, yet easy-

to-use graphical user interface of MPLAB Integrated

Development Environment (IDE).

The MPLAB ICD 3 In-Circuit Debugger probe is con-

nected to the design engineer's PC using a high-speed

USB 2.0 interface and is connected to the target with a

connector compatible with the MPLAB ICD 2 or MPLAB

REAL ICE systems (RJ-11). MPLAB ICD 3 supports all

MPLAB ICD 2 headers.

31.10 PICkit 3 In-Circuit Debugger/

Programmer and

PICkit 3 Debug Express

The MPLAB PICkit 3 allows debugging and program-

ming of PIC® and dsPIC® Flash microcontrollers at a

most affordable price point using the powerful graphical

user interface of the MPLAB Integrated Development

Environment (IDE). The MPLAB PICkit 3 is connected

to the design engineer's PC using a full speed USB

interface and can be connected to the target via an

Microchip debug (RJ-11) connector (compatible with

MPLAB ICD 3 and MPLAB REAL ICE). The connector

uses two device I/O pins and the reset line to imple-

ment in-circuit debugging and In-Circuit Serial Pro-

gramming™.

The PICkit 3 Debug Express include the PICkit 3, demo

board and microcontroller, hookup cables and CDROM

with user’s guide, lessons, tutorial, compiler and

MPLAB IDE software.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 498  2009-2012 Microchip Technology Inc.

31.11 PICkit 2 Development

Programmer/Debugger and

PICkit 2 Debug Express

The PICkit™ 2 Development Programmer/Debugger is

a low-cost development tool with an easy to use inter-

face for programming and debugging Microchip’s Flash

families of microcontrollers. The full featured

Windows® programming interface supports baseline

(PIC10F, PIC12F5xx, PIC16F5xx), midrange

(PIC12F6xx, PIC16F), PIC18F, PIC24, dsPIC30,

dsPIC33, and PIC32 families of 8-bit, 16-bit, and 32-bit

microcontrollers, and many Microchip Serial EEPROM

products. With Microchip’s powerful MPLAB Integrated

Development Environment (IDE) the PICkit™ 2

enables in-circuit debugging on most PIC® microcon-

trollers. In-Circuit-Debugging runs, halts and single

steps the program while the PIC microcontroller is

embedded in the application. When halted at a

breakpoint, the file registers can be examined and

modified.

The PICkit 2 Debug Express include the PICkit 2, demo

board and microcontroller, hookup cables and CDROM

with user’s guide, lessons, tutorial, compiler and

MPLAB IDE software.

31.12 MPLAB PM3 Device Programmer

The MPLAB PM3 Device Programmer is a universal,

CE compliant device programmer with programmable

voltage verification at VDDMIN and VDDMAX for

maximum reliability. It features a large LCD display

(128 x 64) for menus and error messages and a modu-

lar, detachable socket assembly to support various

package types. The ICSP™ cable assembly is included

as a standard item. In Stand-Alone mode, the MPLAB

PM3 Device Programmer can read, verify and program

PIC devices without a PC connection. It can also set

code protection in this mode. The MPLAB PM3

connects to the host PC via an RS-232 or USB cable.

The MPLAB PM3 has high-speed communications and

optimized algorithms for quick programming of large

memory devices and incorporates an MMC card for file

storage and data applications.

31.13 Demonstration/Development

Boards, Evaluation Kits, and

Starter Kits

A wide variety of demonstration, development and

evaluation boards for various PIC MCUs and dsPIC

DSCs allows quick application development on fully func-

tional systems. Most boards include prototyping areas for

adding custom circuitry and provide application firmware

and source code for examination and modification.

The boards support a variety of features, including LEDs,

temperature sensors, switches, speakers, RS-232

interfaces, LCD displays, potentiometers and additional

EEPROM memory.

The demonstration and development boards can be

used in teaching environments, for prototyping custom

circuits and for learning about various microcontroller

applications.

In addition to the PICDEM™ and dsPICDEM™ demon-

stration/development board series of circuits, Microchip

has a line of evaluation kits and demonstration software

for analog filter design, KEELOQ® security ICs, CAN,

IrDA®, PowerSmart battery management, SEEVAL®

evaluation system, Sigma-Delta ADC, flow rate

sensing, plus many more.

Also available are starter kits that contain everything

needed to experience the specified device. This usually

includes a single application and debug capability, all

on one board.

Check the Microchip web page (www.microchip.com)

for the complete list of demonstration, development

and evaluation kits.

 2009-2012 Microchip Technology Inc. DS70616G-page 499

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

32.0 ELECTRICAL CHARACTERISTICS

This section provides an overview of dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

electrical characteristics. Additional information will be provided in future revisions of this document as it becomes

available.

Absolute maximum ratings for the dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814 family

are listed below. Exposure to these maximum rating conditions for extended periods may affect device reliability.

Functional operation of the device at these or any other conditions above the parameters indicated in the operation

listings of this specification is not implied.

Absolute Maximum Ratings

(See Note 1)

Ambient temperature under bias.............................................................................................................-40°C to +125°C

Storage temperature .............................................................................................................................. -65°C to +150°C

Voltage on VDD with respect to VSS .......................................................................................................... -0.3V to +4.0V

Voltage on any pin that is not 5V tolerant, with respect to VSS(3).................................................... -0.3V to (VDD + 0.3V)

Voltage on any 5V tolerant pin with respect to VSS when VDD 3.0V(3)................................................... -0.3V to +5.5V

Voltage on any 5V tolerant pin with respect to Vss when VDD < 3.0V(3)..................................................... -0.3V to 3.6V

Voltage on D+ OR D- pin with respect to VUSB3V3 ................................................................... -0.3V to (VUSB3V3 +0.3V)

Voltage on VBUS with respect to VSS ........................................................................................................ -0.3V to +5.5V

Maximum current out of VSS pin ...........................................................................................................................320 mA

Maximum current into VDD pin(2)...........................................................................................................................320 mA

Maximum current sourced/sunk by any 4x I/O pin(4)..............................................................................................15 mA

Maximum current sourced/sunk by any 8x I/O pin(4)..............................................................................................25 mA

Maximum current sunk by all ports .......................................................................................................................200 mA

Maximum current sourced by all ports(2)...............................................................................................................200 mA

Note 1: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the

device. This is a stress rating only and functional operation of the device at those or any other conditions

above those indicated in the operation listings of this specification is not implied. Exposure to maximum

rating conditions for extended periods may affect device reliability.

2: Maximum allowable current is a function of device maximum power dissipation (see Table 32-2).

3: See the “Pin Diagrams” section for the 5V tolerant pins.

4: Characterized but not tested.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 500  2009-2012 Microchip Technology Inc.

32.1 DC Characteristics

TABLE 32-1: OPERATING MIPS VS. VOLTAGE

Characteristic VDD Range

(in Volts)

Temp Range

(in °C)

Maximum MIPS

dsPIC33EPXXX(GP/MC/MU)806/810/

814 and PIC24EPXXX(GP/GU)810/814

— 2.95V-3.6V(1)-40°C to +85°C 70

— 2.95V-3.6V(1)-40°C to +125°C 60

Note 1: Device is functional at VBORMIN < VDD < VDDMIN. Analog modules: ADC, Comparator and DAC will have

degraded performance. Device functionality is tested but not characterized. Refer to Parameter BO10 in

Table 32-11 for the minimum and maximum BOR values.

TABLE 32-2: THERMAL OPERATING CONDITIONS

Rating Symbol Min. Typ. Max. Unit

Industrial Temperature Devices

Operating Junction Temperature Range TJ-40 — +125 °C

Operating Ambient Temperature Range TA-40 — +85 °C

Extended Temperature Devices

Operating Junction Temperature Range TJ-40 — +140 °C

Operating Ambient Temperature Range TA-40 — +125 °C

Power Dissipation:

Internal chip power dissipation:

PINT = VDD x (IDD –  IOH) PDPINT + PI/OW

I/O Pin Power Dissipation:

I/O =  ({VDD – VOH} x IOH) +  (VOL x IOL)

Maximum Allowed Power Dissipation PDMAX (TJ – TA)/JA W

TABLE 32-3: THERMAL PACKAGING CHARACTERISTICS

Characteristic Symbol Typ. Max. Unit Notes

Package Thermal Resistance, 64-pin QFN (9x9 mm) JA 28 — °C/W 1

Package Thermal Resistance, 64-pin TQFP (10x10 mm) JA 47 — °C/W 1

Package Thermal Resistance, 100-pin TQFP (12x12 mm) JA 43 — °C/W 1

Package Thermal Resistance, 100-pin TQFP (14x14 mm) JA 43 — °C/W 1

Package Thermal Resistance, 121-pin TFBGA (10x10 mm) JA 40 — °C/W 1

Package Thermal Resistance, 144-pin LQFP (20x20 mm) JA 33 — °C/W 1

Package Thermal Resistance, 144-pin TQFP (16x16 mm) JA 33 — °C/W 1

Note 1: Junction to ambient thermal resistance, Theta-JA (JA) numbers are achieved by package simulations.

 2009-2012 Microchip Technology Inc. DS70616G-page 501

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 32-4: DC TEMPERATURE AND VOLTAGE SPECIFICATIONS

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Symbol Characteristic Min. Typ.(1)Max. Units Conditions

Operating Voltage

DC10 VDD Supply Voltage(3)3.0 — 3.6 V

DC12 VDR RAM Data Retention Voltage(2)1.8 — — V

DC16 VPOR VDD Start Voltage

to Ensure Internal

Power-on Reset Signal

——VSS V

DC17 SVDD VDD Rise Rate

to Ensure Internal

Power-on Reset Signal

1.0 — — V/ms 0-3.0V in 3 ms

Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

2: This is the limit to which VDD may be lowered without losing RAM data.

3: Device is functional at VBORMIN < VDD < VDDMIN. Analog modules: ADC, Comparator and DAC will have

degraded performance. Device functionality is tested but not characterized. Refer to Parameter BO10 in

Table 32-11 for the minimum and maximum BOR values.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 502  2009-2012 Microchip Technology Inc.

TABLE 32-5: DC CHARACTERISTICS: OPERATING CURRENT (IDD)

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param.(2)Typ.(3)Max. Units Conditions

Operating Current (IDD)(1)

DC20d 12 18 mA -40°C

3.3V 10 MIPS

DC20a 12 18 mA +25°C

DC20b 13 20 mA +85°C

DC20c 14 21 mA +125°C

DC22d 23 35 mA -40°C

3.3V 20 MIPS

DC22a 24 36 mA +25°C

DC22b 24 36 mA +85°C

DC22c 25 38 mA +125°C

DC24d 42 63 mA -40°C

3.3V 40 MIPS

DC24a 43 65 mA +25°C

DC24b 44 66 mA +85°C

DC24c 45 68 mA +125°C

DC25d 61 92 mA -40°C

3.3V 60 MIPS

DC25a 62 93 mA +25°C

DC25b 62 93 mA +85°C

DC25c 63 95 mA +125°C

DC26d 69 104 mA -40°C

3.3V 70 MIPSDC26a 70 105 mA +25°C

DC26b 70 105 mA +85°C

Note 1: IDD is primarily a function of the operating voltage and frequency. Other factors, such as I/O pin loading

and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact

on the current consumption. The test conditions for all IDD measurements are as follows:

• Oscillator is configured in EC mode and external clock is active, OSC1 is driven with external square

wave from rail-to-rail (EC Clock Overshoot/Undershoot < 250 mV required)

• CLKO is configured as an I/O input pin in the Configuration Word

• All I/O pins are configured as inputs and pulled to VSS

•MCLR = VDD, WDT and FSCM are disabled

• CPU, SRAM, program memory and data memory are operational

• No peripheral modules are operating; however, every peripheral is being clocked (defined PMDx bits

are set to zero and unimplemented PMDx bits are set to one)

• CPU is executing while(1) statement

• JTAG is disabled

2: These parameters are characterized but not tested in manufacturing.

3: Data in “Typ” column is at 3.3V, +25ºC unless otherwise stated.

 2009-2012 Microchip Technology Inc. DS70616G-page 503

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 32-6: DC CHARACTERISTICS: IDLE CURRENT (IIDLE)

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param.(2)Typ.(3)Max. Units Conditions

Idle Current (IIDLE)(1)

DC40d 6 10 mA -40°C

3.3V 10 MIPS

DC40a 7 12 mA +25°C

DC40b 8 13 mA +85°C

DC40c 9 15 mA +125°C

DC42d 11 18 mA -40°C

3.3V 20 MIPS

DC42a 12 20 mA +25°C

DC42b 13 21 mA +85°C

DC42c 15 24 mA +125°C

DC44d 23 37 mA -40°C

3.3V 40 MIPS

DC44a 24 39 mA +25°C

DC44b 25 40 mA +85°C

DC44c 27 44 mA +125°C

DC45d 34 55 mA -40°C

3.3V 60 MIPS

DC45a 35 56 mA +25°C

DC45b 36 58 mA +85°C

DC45c 38 61 mA +125°C

DC46d 39 63 mA -40°C

3.3V 70 MIPSDC46a 41 66 mA +25°C

DC46b 42 68 mA +85°C

Note 1: Base IIDLE current is measured as follows:

• CPU core is off, oscillator is configured in EC mode and external clock is active, OSC1 is driven with

external square wave from rail-to-rail (EC Clock Overshoot/Undershoot < 250 mV required)

• CLKO is configured as an I/O input pin in the Configuration Word

• External Secondary Oscillator (SOSC) is disabled (i.e., SOSCO and SOSCI pins are configured as

digital I/O inputs)

• All I/O pins are configured as inputs and pulled to VSS

•MCLR = VDD, WDT and FSCM are disabled

• No peripheral modules are operating; however, every peripheral is being clocked (defined PMDx bits

are set to zero and unimplemented PMDx bits are set to one)

• The NVMSIDL bit (NVMCON<12>) = 1 (i.e., Flash regulator is set to stand-by while the device is in

Idle mode)

• JTAG is disabled

2: These parameters are characterized but not tested in manufacturing.

3: Data in “Typ” column is at 3.3V, +25ºC unless otherwise stated.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 504  2009-2012 Microchip Technology Inc.

TABLE 32-7: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD)

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Typ.(2)Max. Units Conditions

Power-Down Current (IPD)(1)

DC60d 50 100 A -40°C

3.3V Base Power-Down Current(1,4)

DC60a 60 200 A +25°C

DC60b 250 500 A +85°C

DC60c 1600 3000 A +125°C

DC61d 8 10 A -40°C

3.3V Watchdog Timer Current: IWDT(3)

DC61a 10 15 A +25°C

DC61b 12 20 A +85°C

DC61c 13 25 A +125°C

Note 1: IPD (Sleep) current is measured as follows:

• CPU core is off, oscillator is configured in EC mode and external clock is active, OSC1 is driven with

external square wave from rail-to-rail (EC Clock Overshoot/Undershoot < 250 mV required)

• CLKO is configured as an I/O input pin in the Configuration Word

• External Secondary Oscillator (SOSC) is disabled (i.e., SOSCO and SOSCI pins are configured as

digital I/O inputs)

• All I/O pins are configured as inputs and pulled to VSS

•MCLR = VDD, WDT and FSCM are disabled, all peripheral modules are disabled (PMDx bits are

all ones)

• The VREGS bit (RCON<8>) = 0 (i.e., core regulator is set to stand-by while the device is in Sleep

mode)

• RTCC is disabled

• The VREGSF bit (RCON<11>) = 0 (i.e., Flash regulator is set to stand-by while the device is in

Sleep mode)

• JTAG is disabled

2: Data in the “Typ” column is at 3.3V, +25ºC unless otherwise stated.

3: The Watchdog Timer current is the additional current consumed when the WDT module is enabled. This

current should be added to the base IPD current.

4: These currents are measured on the device containing the most memory in this family.

 2009-2012 Microchip Technology Inc. DS70616G-page 505

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 32-8: DC CHARACTERISTICS: DOZE CURRENT (IDOZE)(1)

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  T

A  +85°C for Industrial

-40°C  TA  +125°C for Extended

Parameter Typ.(2)Max. Doze

Ratio Units Conditions

DC73a 57 86 1:2 mA -40°C 3.3V 70 MIPS

DC73g 40 60 1:128 mA

DC70a 58 87 1:2 mA +25°C 3.3V 70 MIPS

DC70g 41 62 1:128 mA

DC71a 58 87 1:2 mA +85°C 3.3V 70 MIPS

DC71g 42 63 1:128 mA

DC72a 53 80 1:2 mA +125°C 3.3V 60 MIPS

DC72g 38 57 1:128 mA

Note 1: IDOZE is primarily a function of the operating voltage and frequency. Other factors, such as I/O pin loading

and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact

on the current consumption. The test conditions for all IDOZE measurements are as follows:

• Oscillator is configured in EC mode and external clock is active, OSC1 is driven with external square

wave from rail-to-rail with Overshoot/Undershoot < 250 mV

• CLKO is configured as an I/O input pin in the Configuration Word

• All I/O pins are configured as inputs and pulled to VSS

•MCLR = VDD, WDT and FSCM are disabled

• CPU, SRAM, program memory and data memory are operational

• No peripheral modules are operating; however, every peripheral is being clocked (defined PMDx bits

are set to zero and unimplemented PMDx bits are set to one)

• CPU executing while(1) statement

• JTAG is disabled

2: Data in the “Typ” column is at 3.3V, +25ºC unless otherwise stated.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 506  2009-2012 Microchip Technology Inc.

TABLE 32-9: DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic Min. Typ(1)Max. Units Conditions

VIL Input Low Voltage

DI10 I/O Pins VSS —0.2VDD V

DI11 PMP Pins VSS —0.15VDD VPMPTTL = 1

DI15 MCLR VSS —0.2VDD V

DI16 I/O Pins with OSC1 or SOSCI VSS —0.2VDD V

DI18 I/O Pins with SDAx, SCLx VSS — 0.3 VDD V SMBus disabled

DI19 I/O Pins with SDAx, SCLx VSS — 0.8 V SMBus enabled

VIH Input High Voltage

DI20 I/O Pins Not 5V Tolerant(4)

I/O Pins 5V Tolerant(4)

PMP Pins

I/O Pins with SDAx, SCLx

0.7 VDD

0.25 VDD + 0.8

0.7 VDD

2.1

—

VDD

5.3

—

5.3

PMPTTL = 1

SMBus disabled

SMBus enabled

ICNPU Change Notification Pull-up

Current

DI30 50 250 400 AVDD = 3.3V, VPIN = VSS

ICNPD Change Notification

Pull-down Current(10)

DI31 — 50 — AVDD = 3.3V, VPIN = VDD

Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified

levels represent normal operating conditions. Higher leakage current can be measured at different input

voltages.

3: Negative current is defined as current sourced by the pin.

4: See “Pin Diagrams” for the 5V tolerant I/O pins.

5: VIL source < (VSS – 0.3). Characterized but not tested.

6: Non-5V tolerant pins VIH source > (VDD + 0.3), 5V tolerant pins VIH source > 5.5V. Characterized but not

tested.

7: Digital 5V tolerant pins cannot tolerate any “positive” input injection current from input sources > 5.5V.

8: Injection currents > | 0 | can affect the ADC results by approximately 4-6 counts.

9: Any number and/or combination of I/O pins not excluded under IICL or IICH conditions are permitted, pro-

vided the mathematical “absolute instantaneous” sum of the input injection currents from all pins do not

exceed the specified limit. Characterized but not tested.

10: These parameters are characterized, but not tested.

 2009-2012 Microchip Technology Inc. DS70616G-page 507

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

IIL Input Leakage Current(2,3)

DI50 I/O Pins 5V Tolerant(4)——±1AVSS  VPIN  VDD,

Pin at high-impedance

DI51 I/O Pins Not 5V Tolerant(4)——±1AVSS  VPIN  VDD,

Pin at high-impedance,

-40°C  T

A +85°C

DI51a I/O Pins Not 5V Tolerant(4)——±1A Analog pins shared

with external reference

pins,

-40°C  T

A  +85°C

DI51b I/O Pins Not 5V Tolerant(4)——±1AVSS  VPIN  VDD, Pin

at high-impedance,

-40°C TA +125°C

DI51c I/O Pins Not 5V Tolerant(4)——±1A Analog pins shared

with external reference

pins,

-40°C TA +125°C

DI55 MCLR ——±1AVSS VPIN VDD

DI56 OSC1 — — ±1 AVSS VPIN VDD,

XT and HS modes

TABLE 32-9: DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS (CONTINUED)

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic Min. Typ(1)Max. Units Conditions

Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified

levels represent normal operating conditions. Higher leakage current can be measured at different input

voltages.

3: Negative current is defined as current sourced by the pin.

4: See “Pin Diagrams” for the 5V tolerant I/O pins.

5: VIL source < (VSS – 0.3). Characterized but not tested.

6: Non-5V tolerant pins VIH source > (VDD + 0.3), 5V tolerant pins VIH source > 5.5V. Characterized but not

tested.

7: Digital 5V tolerant pins cannot tolerate any “positive” input injection current from input sources > 5.5V.

8: Injection currents > | 0 | can affect the ADC results by approximately 4-6 counts.

9: Any number and/or combination of I/O pins not excluded under IICL or IICH conditions are permitted, pro-

vided the mathematical “absolute instantaneous” sum of the input injection currents from all pins do not

exceed the specified limit. Characterized but not tested.

10: These parameters are characterized, but not tested.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 508  2009-2012 Microchip Technology Inc.

IICL Input Low Injection Current

DI60a

0—-5

(5,8)mA

All pins except VDD,

VSS, AVDD, AVSS,

MCLR, VCAP, RB11,

SOSCI, SOSCO, D+,

D-, VUSB3V3 and VBUS

IICH Input High Injection Current

DI60b

0—+5

(6,7,4)mA

All pins except VDD,

VSS, AVDD, AVSS,

MCLR, VCAP, RB11,

SOSCI, SOSCO, D+,

D-, VUSB3V3 and VBUS,

and all 5V tolerant

pins(7)

IICT Total Input Injection Current

(sum of all I/O and control

pins)

DI60c -20(9)—+20

(9)mA Absolute instantaneous

sum of all ± input

injection currents from

all I/O pins

(| I

ICL + | IICH |)  IICT

TABLE 32-9: DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS (CONTINUED)

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic Min. Typ(1)Max. Units Conditions

Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified

levels represent normal operating conditions. Higher leakage current can be measured at different input

voltages.

3: Negative current is defined as current sourced by the pin.

4: See “Pin Diagrams” for the 5V tolerant I/O pins.

5: VIL source < (VSS – 0.3). Characterized but not tested.

6: Non-5V tolerant pins VIH source > (VDD + 0.3), 5V tolerant pins VIH source > 5.5V. Characterized but not

tested.

7: Digital 5V tolerant pins cannot tolerate any “positive” input injection current from input sources > 5.5V.

8: Injection currents > | 0 | can affect the ADC results by approximately 4-6 counts.

9: Any number and/or combination of I/O pins not excluded under IICL or IICH conditions are permitted, pro-

vided the mathematical “absolute instantaneous” sum of the input injection currents from all pins do not

exceed the specified limit. Characterized but not tested.

10: These parameters are characterized, but not tested.

 2009-2012 Microchip Technology Inc. DS70616G-page 509

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 32-10: DC CHARACTERISTICS: I/O PIN OUTPUT SPECIFICATIONS

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Symbol Characteristic Min. Typ. Max. Units Conditions

DO10 VOL

Output Low Voltage

I/O Pins:

4x Sink Driver Pins – All I/O Pins

except OSC2 and SOSCO

——0.4VI

OL  10 mA, VDD = 3.3V

Output Low Voltage

I/O Pins:

8x Sink Driver Pins – OSC2 and

SOSCO

——0.4VI

OL  15 mA, VDD = 3.3V

DO20 VOH

Output High Voltage

I/O Pins:

4x Sink Driver Pins – All I/O Pins

except OSC2 and SOSCO

2.4 — — V IOH -10 mA, VDD = 3.3V

Output High Voltage

I/O Pins:

8x Sink Driver Pins – OSC2 and

SOSCO

2.4 — — V IOH -15 mA, VDD = 3.3V

DO20A VOH1

Output High Voltage

I/O Pins:

4x Sink Driver Pins – All I/O Pins

except OSC2 and SOSCO

1.5(1)——

IOH -14 mA, VDD = 3.3V

2.0(1)—— IOH -12 mA, VDD = 3.3V

3.0(1)—— IOH -7 mA, VDD = 3.3V

Output High Voltage

I/O Pins:

8x Sink Driver Pins – OSC2 and

SOSCO

1.5(1)——

IOH -22 mA, VDD = 3.3V

2.0(1)—— IOH -18 mA, VDD = 3.3V

3.0(1)—— IOH -10 mA, VDD = 3.3V

Note 1: Parameters are characterized, but not tested.

TABLE 32-11: ELECTRICAL CHARACTERISTICS: BOR

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V(2)

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Symbol Characteristic Min.(1)Typ. Max. Units Conditions

BO10 VBOR BOR Event on VDD Transition

High-to-Low

2.7 — 2.9 V VDD

Note 1: Parameters are for design guidance only and are not tested in manufacturing.

2: Device is functional at VBORMIN < VDD < VDDMIN. Analog modules: ADC, Comparator and DAC will have

degraded performance. Device functionality is tested but not characterized.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 510  2009-2012 Microchip Technology Inc.

TABLE 32-13: INTERNAL VOLTAGE REGULATOR SPECIFICATIONS

TABLE 32-12: DC CHARACTERISTICS: PROGRAM MEMORY

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Symbol Characteristic Min. Typ(1)Max. Units Conditions

Program Flash Memory

D130 EPCell Endurance 10,000 — — E/W -40C to +125C

D131 VPR VDD for Read 3.0 — 3.6 V

D132b VPEW VDD for Self-Timed Write 3.0 — 3.6 V

D134 TRETD Characteristic Retention 20 — — Year Provided no other specifications

are violated, -40C to +125C

D135 IDDP Supply Current during

Programming

—10 —mA

D136a TRW Row Write Time 1.32 — 1.74 ms TRW = 11064 FRC cycles,

TA = +85°C, See Note 2

D136b TRW Row Write Time 1.28 — 1.79 ms TRW = 11064 FRC cycles,

TA = +125°C, See Note 2

D137a TPE Page Erase Time 20.1 — 26.5 ms TPE = 168517 FRC cycles,

TA = +85°C, See Note 2

D137b TPE Page Erase Time 19.5 — 27.3 ms TPE = 168517 FRC cycles,

TA = +125°C, See Note 2

D138a TWW Word Write Cycle Time 42.3 — 55.9 µs TWW = 355 FRC cycles,

TA = +85°C, See Note 2

D138b TWW Word Write Cycle Time 41.1 — 57.6 µs TWW = 355 FRC cycles,

TA = +125°C, See Note 2

Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

2: Other conditions: FRC = 7.37 MHz, TUN<5:0> = 'b011111 (for Minimum), TUN<5:0> = 'b100000 (for

Maximum). This parameter depends on the FRC accuracy (see Table 32-20) and the value of the FRC

Oscillator Tuning register (see Register 9-4). For complete details on calculating the Minimum and

Maximum time, see Section 5.3 “Programming Operations”.

Standard Operating Conditions (unless otherwise stated):

Operating temperature -40°C  T

A  +85°C for Industrial

-40°C  T

A  +125°C for Extended

Param. Symbol Characteristics Min. Typ Max. Units Comments

—C

EFC(1)External Filter Capacitor

Value

4.7 10 — F Capacitor must have a low

series resistance (< 1 Ohm)

Note 1: Typical VCAP (CEFC) voltage = 1.8V when VDD  VDDMIN.

 2009-2012 Microchip Technology Inc. DS70616G-page 511

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

32.2 AC Characteristics and Timing

Parameters

This section defines the dsPIC33EPXXX(GP/MC/

MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

AC characteristics and timing parameters.

TABLE 32-14: TEMPERATURE AND VOLTAGE SPECIFICATIONS – AC

FIGURE 32-1: LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS

TABLE 32-15: CAPACITIVE LOADING REQUIREMENTS ON OUTPUT PINS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Operating voltage VDD range as described in Section 32.1 “DC

Characteristics”.

Param. Symbol Characteristic Min. Typ. Max. Units Conditions

DO50 COSCO OSC2 Pin — — 15 pF In XT and HS modes when

external clock is used to drive

OSC1

DO56 CIO All I/O Pins and OSC2 — — 50 pF EC mode

DO58 CBSCLx, SDAx — — 400 pF In I2C™ mode

VDD/2

VSS

RL=464

CL= 50 pF for All Pins Except OSC2

15 pF for OSC2 Output

Load Condition 1 – for all pins except OSC2 Load Condition 2 – for OSC2

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 512  2009-2012 Microchip Technology Inc.

FIGURE 32-2: EXTERNAL CLOCK TIMING

Q1 Q2 Q3 Q4

OSC1

CLKO

Q1 Q2 Q3 Q4

OS20

OS25

OS30 OS30

OS40

OS41

OS31 OS31

TABLE 32-16: EXTERNAL CLOCK TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Symbol Characteristic Min. Typ.(1)Max. Units Conditions

OS10 FIN External CLKI Frequency

(External clocks allowed only

in EC and ECPLL modes)

DC — 60 MHz EC

Oscillator Crystal Frequency 3.5

32.4

—

32.768

33.1

MHz

kHz

SOSC

OS20 TOSC TOSC = 1/FOSC 8.33

7.14

—

+125ºC

+85ºC

OS25 TCY Instruction Cycle Time(2)16.67

14.28

—

+125ºC

+85ºC

OS30 TosL,

Tos H

External Clock In (OSC1)

High or Low Time

0.375 x TOSC — 0.625 x TOSC ns EC

OS31 TosR,

Tos F

External Clock In (OSC1)

Rise or Fall Time

— — 20 ns EC

OS40 TckR CLKO Rise Time(3) —5.2— ns

OS41 TckF CLKO Fall Time(3)—5.2—ns

OS42 GMExternal Oscillator

Transconductance(4)

— 12 — mA/V HS, VDD = 3.3V,

TA = +25ºC

—6—mA/VXT, V

DD = 3.3V,

TA = +25ºC

Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

2: Instruction cycle period (TCY) equals two times the input oscillator time base period. All specified values

are based on characterization data for that particular oscillator type under standard operating conditions

with the device executing code. Exceeding these specified limits may result in an unstable oscillator

operation and/or higher than expected current consumption. All devices are tested to operate at

“Minimum” values with an external clock applied to the OSC1 pin. When an external clock input is used,

the “Maximum” cycle time limit is “DC” (no clock) for all devices.

3: Measurements are taken in EC mode. The CLKO signal is measured on the OSC2 pin.

4: This parameter is characterized, but not tested in manufacturing.

 2009-2012 Microchip Technology Inc. DS70616G-page 513

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 32-17: PLL CLOCK TIMING SPECIFICATIONS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Symbol Characteristic Min. Typ.(1)Max. Units Conditions

OS50 FPLLI PLL Voltage Controlled

Oscillator (VCO) Input

Frequency Range

0.8 — 8.0 MHz ECPLL, XTPLL modes

OS51 FSYS On-Chip VCO System

Frequency

120 — 340 MHz

OS52 TLOCK PLL Start-up Time (Lock Time) 0.9 1.5 3.1 mS

OS53 DCLK CLKO Stability (Jitter)(2)-5 0.5 5 %

Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only

and are not tested.

2: This jitter specification is based on clock cycle-by-clock cycle measurements. To get the effective jitter for

individual time bases or communication clocks used by the application, use the following formula:

For example, if FOSC = 120 MHz and the SPI bit rate = 10 MHz, the effective jitter is as follows:

Effective Jitter DCLK

FOSC

Time Base or Communication Clock

---------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------=

Effective Jitter DCLK

120

---------

--------------DCLK

3.464

--------------===

TABLE 32-18: AUXILIARY PLL CLOCK TIMING SPECIFICATIONS

(dsPIC33EPXXXMU8XX AND PIC24EPXXXGU8XX DEVICES ONLY)

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (unless otherwise

stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Symbol Characteristic Min. Typ.(1)Max. Units Conditions

OS54 AFPLLI PLL Voltage Controlled

Oscillator (VCO) Input

Frequency Range

3 — 5.5 MHz ECPLL, XTPLL modes

OS55 AFSYS On-Chip VCO System

Frequency

60 — 120 MHz

OS56 ATLOCK PLL Start-up Time (Lock Time) 0.9 1.5 3.1 mS

OS57 ADCLK CLKO Stability (Jitter) -2 0.25 2 %

Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only

and are not tested.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 514  2009-2012 Microchip Technology Inc.

TABLE 32-19: INTERNAL FRC ACCURACY

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  T

A  +125°C for Extended

Param. Characteristic Min. Typ. Max. Units Conditions

Internal FRC Accuracy @ FRC Frequency = 7.37 MHz(1)

F20a FRC -2 — +2 % -40°C  TA +85°C VDD = 3.0-3.6V

F20b FRC -5 — +5 % -40°C  TA  +125°C VDD = 3.0-3.6V

Note 1: Frequency calibrated at +25°C and 3.3V. TUNx bits can be used to compensate for temperature drift.

TABLE 32-20: INTERNAL LPRC ACCURACY

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Characteristic Min. Typ. Max. Units Conditions

LPRC @ 32.768 kHz(1)

F21a LPRC -20 ±6 +20 % -40°C  TA  +85°C VDD = 3.0-3.6V

F21b LPRC -50 — +50 % -40°C  T

A  +125°C VDD = 3.0-3.6V

Note 1: Change of LPRC frequency as VDD changes.

 2009-2012 Microchip Technology Inc. DS70616G-page 515

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 32-3: I/O TIMING CHARACTERISTICS

Note: Refer to Figure 32-1 for load conditions.

I/O Pin

(Input)

I/O Pin

(Output)

DI35

Old Value New Value

DI40

DO31

DO32

TABLE 32-21: I/O TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Symbol Characteristic Min. Typ.(1)Max. Units Conditions

DO31 TIOR Port Output Rise Time — 5 10 ns

DO32 TIOF Port Output Fall Time — 5 10 ns

DI35 TINP INTx Pin High or Low Time (input) 20 — — ns

DI40 TRBP CNx High or Low Time (input) 2 — — TCY

Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 516  2009-2012 Microchip Technology Inc.

FIGURE 32-4: POWER-ON RESET TIMING CHARACTERISTICS

VDD

VPOR

Note 1: The power-up period will be extended if the power-up sequence completes before the device exits from BOR

(VDD < VBOR).

2: The power-up period includes internal voltage regulator stabilization delay.

SY00

Power-up Sequence

VDD

VPOR

Power-up Timer Enabled – Clock Sources = (FRC, FRCDIVN, FRCDIV16, FRCPLL, EC, ECPLL and LPRC)

Power-up Timer Disabled – Clock Sources = (HS, HSPLL, XT, XTPLL and SOSC)

)

SY10

SY11

Power-up Sequence

(Note 1,2)

CPU Starts Fetching Code

PWRT

)

VDD

VPOR

SY00

Power-up Sequence

Power-up Timer Disabled – Clock Sources = (FRC, FRCDIVN, FRCDIV16, FRCPLL, EC, ECPLL and LPRC)

)

CPU Starts Fetching Code

(Note 1,2)

OST

)

SY00

)

VDD

VPOR

Power-up Timer Enabled – Clock Sources = (HS, HSPLL, XT, XTPLL and SOSC)

Greater of

Power-up Sequence

(Note 1,2)

CPU Starts Fetching Code

SY00

)

SY11 (T

PWRT

)

SY10 (T

OST

)

 2009-2012 Microchip Technology Inc. DS70616G-page 517

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 32-5: BOR AND MASTER CLEAR RESET TIMING CHARACTERISTICS

MCLR

(SY20)

BOR

(SY30)

TMCLR

TBOR

Reset Sequence

CPU Starts Fetching Code

Various Delays (depending on configuration)

TABLE 32-22: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER

TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ.(2)Max. Units Conditions

SY00 TPU Power-up Period — 400 600 s

SY10 TOST Oscillator Start-up Time — 1024 TOSC ——TOSC = OSC1 period

SY11 TPWRT Power-up Timer Period — — — — See Section 29.1 “Configuration

Bits” and LPRC Parameters F21a

and F21b (Ta b l e 3 2 - 2 0 )

SY12 TWDT Watchdog Timer

Time-out Period

— — — — See Section 29.4 “Watchdog

Timer (WDT)” and LPRC

Parameters F21a and F21b

(Table 32-20)

SY13 TIOZ I/O High-Impedance

from MCLR Low or

Watchdog Timer Reset

0.68 0.72 1.2 s

SY20 TMCLR MCLR Pulse Width (low) 2 — — s

SY30 TBOR BOR Pulse Width (low) 1 — — s

SY35 TFSCM Fail-Safe Clock Monitor

Delay

— 500 900 s -40°C to +85°C

SY36 TVREG Voltage Regulator

Standby-to-Active Mode

Transition Time

——30µs

SY37 TOSCDFRC FRC Oscillator Start-up

Delay

——29µs

SY38 TOSCDLPRC LPRC Oscillator Start-up

Delay

——70µs

Note 1: These parameters are characterized but not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 518  2009-2012 Microchip Technology Inc.

FIGURE 32-6: TIMER1-TIMER9 EXTERNAL CLOCK TIMING CHARACTERISTICS

Note: Refer to Figure 32-1 for load conditions.

Tx11

Tx15

Tx10

Tx20

TMRx

OS60

TxCK

TABLE 32-23: TIMER1 EXTERNAL CLOCK TIMING REQUIREMENTS(1)

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(2)Min. Typ. Max. Units Conditions

TA10 TTXH TxCK High

Time

Synchronous

mode

Greater of:

20 or

(TCY + 20)/N

— — ns Must also meet

Parameter TA15,

N = prescaler value

(1, 8, 64, 256)

Asynchronous 35 — — ns

TA11 TTXLTxCK Low

Time

Synchronous

mode

Greater of:

20 or

(TCY + 20)/N

— — ns Must also meet

Parameter TA15,

N = prescaler value

(1, 8, 64, 256)

Asynchronous 10 — — ns

TA15 TTXP TxCK Input

Period

Synchronous

mode

Greater of:

40 or

(2 TCY + 40)/N

— — ns N = prescale value

(1, 8, 64, 256)

OS60 Ft1 SOSC1/T1CK Oscillator

Input Frequency Range

(oscillator enabled by setting

bit, TCS (T1CON<1>))

DC — 50 kHz

TA20 TCKEXTMRL Delay from External TxCK

Clock Edge to Timer

Increment

0.75 TCY + 40 — 1.75 TCY + 40 ns

Note 1: Timer1 is a Type A.

2: These parameters are characterized, but are not tested in manufacturing.

 2009-2012 Microchip Technology Inc. DS70616G-page 519

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 32-24: TIMER2, TIMER4, TIMER6, TIMER8 (TYPE B TIMER) EXTERNAL CLOCK TIMING

REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ. Max. Units Conditions

TB10 TtxH TxCK High

Time

Synchronous

mode

Greater of:

20 or

(TCY + 20)/N

— — ns Must also meet

Parameter TB15,

N = prescale

value (1, 8, 64, 256)

TB11 TtxL TxCK Low

Time

Synchronous

mode

Greater of:

20 or

(TCY + 20)/N

— — ns Must also meet

Parameter TB15,

N = prescale

value (1, 8, 64, 256)

TB15 TtxP TxCK

Input

Period

Synchronous

mode

Greater of:

40 or

(2 TCY + 40)/N

— — ns N = prescale

value (1, 8, 64, 256)

TB20 TCKEXTMRL Delay from External TxCK

Clock Edge to Timer

Increment

0.75 TCY + 40 — 1.75 TCY + 40 ns

Note 1: These parameters are characterized, but are not tested in manufacturing.

TABLE 32-25: TIMER3, TIMER5, TIMER7, TIMER9 (TYPE C TIMER) EXTERNAL CLOCK TIMING

REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ. Max. Units Conditions

TC10 TtxH TxCK High

Time

Synchronous TCY + 20 — — ns Must also meet

Parameter TC15

TC11 TtxL TxCK Low

Time

Synchronous TCY + 20 — — ns Must also meet

Parameter TC15

TC15 TtxP TxCK Input

Period

Synchronous,

with Prescaler

2 TCY + 40 — — ns N = prescale value

(1, 8, 64, 256)

TC20 TCKEXTMRL Delay from External TxCK

Clock Edge to Timer

Increment

0.75 TCY + 40 — 1.75 TCY + 40 ns

Note 1: These parameters are characterized, but are not tested in manufacturing.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 520  2009-2012 Microchip Technology Inc.

FIGURE 32-7: TIMERQ (QEI MODULE) EXTERNAL CLOCK TIMING CHARACTERISTICS

TABLE 32-26: QEI MODULE EXTERNAL CLOCK TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ. Max. Units Conditions

TQ10 TtQH TQCK High

Time

Synchronous,

with Prescaler

[Greater of

(12.5or 0.5T

CY)/N] + 25

— — ns Must also meet

Parameter TQ15

TQ11 TtQL TQCK Low

Time

Synchronous,

with Prescaler

[Greater of

(12.5or 0.5TCY)/N] + 25

— — ns Must also meet

Parameter TQ15

TQ15 TtQP TQCP Input

Period

Synchronous,

with Prescaler

[Greater of (

25 or TCY)/N] + 50

—— ns

TQ20 TCKEXTMRL Delay from External TxCK

Clock Edge to Timer Increment

—1TCY —

Note 1: These parameters are characterized but not tested in manufacturing.

TQ11

TQ15

TQ10

TQ20

QEB

POSCNT

 2009-2012 Microchip Technology Inc. DS70616G-page 521

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 32-8: INPUT CAPTURE (ICx) TIMING CHARACTERISTICS

ICx

IC10 IC11

IC15

Note: Refer to Figure 32-1 for load conditions.

TABLE 32-27: INPUT CAPTURE MODULE (ICx) TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristics(1)Min. Max. Units Conditions

IC10 TCCL ICx Input Low Time [Greater of

(12.5or 0.5TCY)/N] + 25

— ns Must also meet

Parameter IC15

N = prescale

value (1, 4, 16)

IC11 TCCH ICx Input High Time [Greater of

(12.5or 0.5T

CY)/N] + 25

— ns Must also meet

Parameter IC15

IC15 TCCP ICx Input Period [Greater of

(25or 1TCY)/N] + 50

—ns

Note 1: These parameters are characterized, but not tested in manufacturing.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 522  2009-2012 Microchip Technology Inc.

FIGURE 32-9: OUTPUT COMPARE MODULE (OCx) TIMING CHARACTERISTICS

FIGURE 32-10: OCx/PWMx MODULE TIMING CHARACTERISTICS

OCx

OC11 OC10

(Output Compare

Note: Refer to Figure 32-1 for load conditions.

or PWM Mode)

TABLE 32-28: OUTPUT COMPARE MODULE (OCx) TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  T

A  +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ. Max. Units Conditions

OC10 TccF OCx Output Fall Time — — — ns See Parameter DO32

OC11 TccR OCx Output Rise Time — — — ns See Parameter DO31

Note 1: These parameters are characterized but not tested in manufacturing.

OCFA

OCx

OC20

OC15

Active User-Specified Fault State

TABLE 32-29: OCx/PWMx MODE TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ. Max. Units Conditions

OC15 TFD Fault Input to PWM I/O

Change

——TCY + 20 ns

OC20 TFLT Fault Input Pulse Width TCY + 20 — — ns

Note 1: These parameters are characterized but not tested in manufacturing.

 2009-2012 Microchip Technology Inc. DS70616G-page 523

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 32-11: HIGH-SPEED PWMx MODULE FAULT TIMING CHARACTERISTICS

(dsPIC33EPXXX(MC/MU)806/810/814 DEVICES ONLY)

FIGURE 32-12: HIGH-SPEED PWMx MODULE TIMING CHARACTERISTICS

(dsPIC33EPXXX(MC/MU)806/810/814 DEVICES ONLY)

TABLE 32-30: HIGH-SPEED PWMx MODULE TIMING REQUIREMENTS

(dsPIC33EPXXX(MC/MU)806/810/814 DEVICES ONLY)

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ. Max. Units Conditions

MP10 TFPWM PWM Output Fall Time — — — ns See Parameter DO32

MP11 TRPWM PWM Output Rise Time — — — ns See Parameter DO31

MP20 TFD Fault Input  to PWM

I/O Change

——15ns

MP30 TFH Fault Input Pulse Width 15 — — ns

Note 1: These parameters are characterized but not tested in manufacturing.

Fault Input

PWMx

MP30

MP20

(active-low)

PWMx

MP11 MP10

Note: Refer to Figure 32-1 for load conditions.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 524  2009-2012 Microchip Technology Inc.

FIGURE 32-13: QEA/QEB INPUT CHARACTERISTICS

(dsPIC33EPXXX(MC/MU)806/810/814 DEVICES ONLY)

TQ30

TQ35

QEA

(input)

TQ35

QEB

(input)

TQ36

QEB

Internal

TQ40TQ41

TQ31

TQ31 TQ30

TABLE 32-31: QUADRATURE DECODER TIMING REQUIREMENTS

(dsPIC33EPXXX(MC/MU)806/810/814 DEVICES ONLY)

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Symbol Characteristic(1)Typ.(2)Max. Units Conditions

TQ30 TQUL Quadrature Input Low Time 6 TCY —ns

TQ31 TQUH Quadrature Input High Time 6 TCY —ns

TQ35 TQUIN Quadrature Input Period 12 TCY —ns

TQ36 TQUP Quadrature Phase Period 3 TCY —ns

TQ40 TQUFL Filter Time to Recognize Low

with Digital Filter

3 * N * TCY — ns N = 1, 2, 4, 16, 32, 64,

128 and 256 (Note 3)

TQ41 TQUFH Filter Time to Recognize High

with Digital Filter

3 * N * TCY — ns N = 1, 2, 4, 16, 32, 64,

128 and 256 (Note 3)

Note 1: These parameters are characterized but not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only

and are not tested.

3: N = Index Channel Digital Filter Clock Divide Select bits. Refer to Section 15. “Quadrature Encoder

Interface (QEI)” (DS70601) in the “dsPIC33E/PIC24E Family Reference Manual”. Please see the

Microchip web site for the latest family reference manual sections.

 2009-2012 Microchip Technology Inc. DS70616G-page 525

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 32-14: QEI MODULE INDEX PULSE TIMING CHARACTERISTICS

(dsPIC33EPXXX(MC/MU)806/810/814 DEVICES ONLY)

QEA

(input)

Ungated

Index

QEB

(input)

TQ55

Index Internal

Position Counter

Reset

TQ50

TQ51

TABLE 32-32: QEI INDEX PULSE TIMING REQUIREMENTS

(dsPIC33EPXXX(MC/MU)MU806/810/814 DEVICES ONLY)

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  T

A  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Symbol Characteristic(1)Min. Max. Units Conditions

TQ50 TqIL Filter Time to Recognize Low

with Digital Filter

3 * N * TCY — ns N = 1, 2, 4, 16, 32, 64,

128 and 256 (Note 2)

TQ51 TqiH Filter Time to Recognize High

with Digital Filter

3 * N * TCY — ns N = 1, 2, 4, 16, 32, 64,

128 and 256 (Note 2)

TQ55 Tqidxr Index Pulse Recognized to Position

Counter Reset (ungated index)

3 TCY —ns

Note 1: These parameters are characterized but not tested in manufacturing.

2: Alignment of index pulses to QEA and QEB is shown for position counter Reset timing only. Shown for

forward direction only (QEA leads QEB). Same timing applies for reverse direction (QEA lags QEB) but

index pulse recognition occurs on the falling edge.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 526  2009-2012 Microchip Technology Inc.

TABLE 32-33: SPI1, SPI3 AND SPI4 MAXIMUM DATA/CLOCK RATE SUMMARY

FIGURE 32-15: SPI1, SPI3 AND SPI4 MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY,

CKE = 0) TIMING CHARACTERISTICS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Maximum

Data Rate

Master

Transmit Only

(Half-Duplex)

Master

Transmit/Receive

(Full-Duplex)

Slave

Transmit/Receive

(Full-Duplex)

CKE CKP SMP

15 MHz Table 32-33 ——0,10,10,1

9 MHz — Table 32-34 —10,11

9 MHz — Table 32-35 —00,11

15 MHz — — Table 32-36 100

11 MHz — — Table 32-37 110

15 MHz — — Table 32-38 010

11 MHz — — Table 32-39 000

SCKx

(CKP = 0)

SCKx

(CKP = 1)

SDOx

SP10

SP21SP20

SP35

SP20SP21

MSb LSbBit 14 - - - - - -1

SP30, SP31

Note: Refer to Figure 32-1 for load conditions.

 2009-2012 Microchip Technology Inc. DS70616G-page 527

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 32-16: SPI1, SPI3 AND SPI4 MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY,

CKE = 1) TIMING CHARACTERISTICS

TABLE 32-34: SPI1, SPI3 AND SPI4 MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY) TIMING

REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ.(2)Max. Units Conditions

SP10 TscP Maximum SCKx Frequency — — 15 MHz See Note 3

SP20 TscF SCKx Output Fall Time — — — ns See Parameter DO32

and Note 4

SP21 TscR SCKx Output Rise Time — — — ns See Parameter DO31

and Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See Parameter DO32

and Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See Parameter DO31

and Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

—620ns

SP36 TdiV2scH,

TdiV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

3: The minimum clock period for SCKx is 66.7 ns. Therefore, the clock generated in Master mode must not

violate this specification.

4: Assumes 50 pF load on all SPIx pins.

SCKx

(CKP = 0)

SCKx

(CKP = 1)

SDOx

SP21

SP20

SP35

SP20

SP21

MSb LSb

Bit 14 - - - - - -1

SP30, SP31

Note: Refer to Figure 32-1 for load conditions.

SP36

SP10

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 528  2009-2012 Microchip Technology Inc.

FIGURE 32-17: SPI1, SPI3 AND SPI4 MASTER MODE (FULL-DUPLEX, CKE = 1, CKP = x,

SMP = 1) TIMING CHARACTERISTICS

TABLE 32-35: SPI1, SPI3 AND SPI4 MASTER MODE (FULL-DUPLEX, CKE = 1, CKP = x, SMP = 1)

TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ.(2)Max. Units Conditions

SP10 TscP Maximum SCKx Frequency — — 9 MHz See Note 3

SP20 TscF SCKx Output Fall Time — — — ns See Parameter DO32

and Note 4

SP21 TscR SCKx Output Rise Time — — — ns See Parameter DO31

and Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See Parameter DO32

and Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See Parameter DO31

and Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid After

SCKx Edge

— 6 20 ns

SP36 TdoV2sc,

TdoV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns

SP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data

Input to SCKx Edge

30 — — ns

SP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

30 — — ns

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

3: The minimum clock period for SCKx is 111 ns. The clock generated in Master mode must not violate this

specification.

4: Assumes 50 pF load on all SPIx pins.

SCKx

(CKP = 0)

SCKx

(CKP = 1)

SDOx

SP21SP20

SP35

SP20SP21

MSb LSb

Bit 14 - - - - - -1

SP30, SP31

Note: Refer to Figure 32-1 for load conditions.

SP36

SP41

LSb In

Bit 14 - - - -1

SDIx

SP40

SP10

MSb In

 2009-2012 Microchip Technology Inc. DS70616G-page 529

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 32-18: SPI1, SPI3 AND SPI4 MASTER MODE (FULL-DUPLEX, CKE = 0, CKP = x,

SMP = 1) TIMING CHARACTERISTICS

TABLE 32-36: SPI1, SPI3 AND SPI4 MASTER MODE (FULL-DUPLEX, CKE = 0, CKP = x, SMP = 1)

TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ.(2)Max. Units Conditions

SP10 TscP Maximum SCKx Frequency — — 9 MHz -40ºC to +125ºC and

see Note 3

SP20 TscF SCKx Output Fall Time — — — ns See Parameter DO32

and Note 4

SP21 TscR SCKx Output Rise Time — — — ns See Parameter DO31

and Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See Parameter DO32

and Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See Parameter DO31

and Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid After

SCKx Edge

— 6 20 ns

SP36 TdoV2scH,

TdoV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns

SP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data

Input to SCKx Edge

30 — — ns

SP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

30 — — ns

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

3: The minimum clock period for SCKx is 111 ns. The clock generated in Master mode must not violate this

specification.

4: Assumes 50 pF load on all SPIx pins.

SCKx

(CKP = 0)

SCKx

(CKP = 1)

SDOx

SDIx

SP40 SP41

SP21

SP20

SP35

SP20

SP21

MSb LSb

Bit 14 - - - - - -1

LSb In

Bit 14 - - - -1

SP30, SP31

Note: Refer to Figure 32-1 for load conditions.

SP36

SP10

MSb In

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 530  2009-2012 Microchip Technology Inc.

FIGURE 32-19: SPI1, SPI3 AND SPI4 SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 0, SMP = 0)

TIMING CHARACTERISTICS

SSx

SCKx

(CKP = 0)

SCKx

(CKP = 1)

SDOx

SDIx

SP60

SP30,SP31

MSb Bit 14 - - - - - -1 LSb

SP51

Bit 14 - - - -1 LSb In

SP52

SP73SP72

SP72SP73

SP40

SP41

Note: Refer to Figure 32-1 for load conditions.

SP36

SP50

SP70

MSb In

SP35

 2009-2012 Microchip Technology Inc. DS70616G-page 531

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 32-37: SPI1, SPI3 AND SPI4 SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 0, SMP = 0)

TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ.(2)Max. Units Conditions

SP70 TscP Maximum SCKx Input Frequency — — 15 MHz See Note 3

SP72 TscF SCKx Input Fall Time — — — ns See Parameter DO32

and Note 4

SP73 TscR SCKx Input Rise Time — — — ns See Parameter DO31

and Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See Parameter DO32

and Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See Parameter DO31

and Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

— 6 20 ns

SP36 TdoV2scH,

TdoV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns

SP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data Input

to SCKx Edge

30 — — ns

SP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

30 — — ns

SP50 TssL2scH,

TssL2scL

SSx  to SCKx  or SCKx 

Input

120 — — ns

SP51 TssH2doZ SSx  to SDOx Output,

High-Impedance

10 — 50 ns See Note 4

SP52 TscH2ssH

TscL2ssH

SSx after SCKx Edge 1.5 TCY + 40 — — ns See Note 4

SP60 TssL2doV SDOx Data Output Valid after

SSx Edge

— — 50 ns

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

3: The minimum clock period for SCKx is 66.7 ns. Therefore, the SCKx clock generated by the master must

not violate this specification.

4: Assumes 50 pF load on all SPIx pins.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 532  2009-2012 Microchip Technology Inc.

FIGURE 32-20: SPI1, SPI3 AND SPI4 SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 1, SMP = 0)

TIMING CHARACTERISTICS

SSx

SCKx

(CKP = 0)

SCKx

(CKP = 1)

SDOx

SDIx

SP60

SP30,SP31

MSb Bit 14 - - - - - -1 LSb

SP51

MSb In Bit 14 - - - -1 LSb In

SP52

SP73SP72

SP72SP73

SP70

SP40

SP41

Note: Refer to Figure 32-1 for load conditions.

SP36

SP50

SP35

 2009-2012 Microchip Technology Inc. DS70616G-page 533

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 32-38: SPI1, SPI3 AND SPI4 SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 1, SMP = 0)

TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ.(2)Max. Units Conditions

SP70 TscP Maximum SCKx Input Frequency — — 11 MHz See Note 3

SP72 TscF SCKx Input Fall Time — — — ns See Parameter DO32

and Note 4

SP73 TscR SCKx Input Rise Time — — — ns See Parameter DO31

and Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See Parameter DO32

and Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See Parameter DO31

and Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

— 6 20 ns

SP36 TdoV2scH,

TdoV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns

SP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data Input

to SCKx Edge

30 — — ns

SP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

30 — — ns

SP50 TssL2scH,

TssL2scL

SSx  to SCKx  or SCKx 

Input

120 — — ns

SP51 TssH2doZ SSx  to SDOx Output,

High-Impedance

10 — 50 ns See Note 4

SP52 TscH2ssH

TscL2ssH

SSx after SCKx Edge 1.5 TCY + 40 — — ns See Note 4

SP60 TssL2doV SDOx Data Output Valid after

SSx Edge

— — 50 ns

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

3: The minimum clock period for SCKx is 91 ns. Therefore, the SCKx clock generated by the master must not

violate this specification.

4: Assumes 50 pF load on all SPIx pins.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 534  2009-2012 Microchip Technology Inc.

FIGURE 32-21: SPI1, SPI3 AND SPI4 SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 1, SMP = 0)

TIMING CHARACTERISTICS

SSX

SCKX

(CKP = 0)

SCKX

(CKP = 1)

SDOX

SP50

SP40

SP41

SP30,SP31 SP51

SP35

MSb LSb

Bit 14 - - - - - -1

Bit 14 - - - -1 LSb In

SP52

SP73SP72

SP72SP73

SP70

Note: Refer to Figure 32-1 for load conditions.

SDIXMSb In

SP36

 2009-2012 Microchip Technology Inc. DS70616G-page 535

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 32-39: SPI1, SPI3 AND SPI4 SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 1, SMP = 0)

TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ.(2)Max. Units Conditions

SP70 TscP Maximum SCKx Input Frequency — — 15 MHz See Note 3

SP72 TscF SCKx Input Fall Time — — — ns See Parameter DO32

and Note 4

SP73 TscR SCKx Input Rise Time — — — ns See Parameter DO31

and Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See Parameter DO32

and Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See Parameter DO31

and Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

— 6 20 ns

SP36 TdoV2scH,

TdoV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns

SP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data Input

to SCKx Edge

30 — — ns

SP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

30 — — ns

SP50 TssL2scH,

TssL2scL

SSx  to SCKx  or SCKx 

Input

120 — — ns

SP51 TssH2doZ SSx  to SDOx Output

High-Impedance

10 — 50 ns See Note 4

SP52 TscH2ssH

TscL2ssH

SSx after SCKx Edge 1.5 TCY + 40 — — ns See Note 4

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

3: The minimum clock period for SCKx is 66.7 ns. Therefore, the SCKx clock generated by the master must

not violate this specification.

4: Assumes 50 pF load on all SPIx pins.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 536  2009-2012 Microchip Technology Inc.

FIGURE 32-22: SPI1, SPI3 AND SPI4 SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 0, SMP = 0)

TIMING CHARACTERISTICS

SSX

SCKX

(CKP = 0)

SCKX

(CKP = 1)

SDOX

SP50

SP40

SP41

SP30,SP31 SP51

SP35

MSb LSb

Bit 14 - - - - - -1

Bit 14 - - - -1 LSb In

SP52

SP73SP72

SP72SP73

SP70

Note: Refer to Figure 32-1 for load conditions.

SDIX

SP36

MSb In

 2009-2012 Microchip Technology Inc. DS70616G-page 537

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 32-40: SPI1, SPI3 AND SPI4 SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 0, SMP = 0)

TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1) Min. Typ.(2)Max. Units Conditions

SP70 TscP Maximum SCKx Input Frequency — — 11 MHz See Note 3

SP72 TscF SCKx Input Fall Time — — — ns See Parameter DO32

and Note 4

SP73 TscR SCKx Input Rise Time — — — ns See Parameter DO31

and Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See Parameter DO32

and Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See Parameter DO31

and Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

— 6 20 ns

SP36 TdoV2scH,

TdoV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns

SP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data Input

to SCKx Edge

30 — — ns

SP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

30 — — ns

SP50 TssL2scH,

TssL2scL

SSx  to SCKx  or SCKx 

Input

120 — — ns

SP51 TssH2doZ SSx  to SDOx Output

High-Impedance

10 — 50 ns See Note 4

SP52 TscH2ssH

TscL2ssH

SSx after SCKx Edge 1.5 TCY + 40 — — ns See Note 4

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

3: The minimum clock period for SCKx is 91 ns. Therefore, the SCKx clock generated by the master must not

violate this specification.

4: Assumes 50 pF load on all SPIx pins.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 538  2009-2012 Microchip Technology Inc.

TABLE 32-41: SPI2 MAXIMUM DATA/CLOCK RATE SUMMARY

FIGURE 32-23: SPI2 MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY, CKE = 0) TIMING

CHARACTERISTICS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Maximum

Data Rate

Master

Transmit Only

(Half-Duplex)

Master

Transmit/Receive

(Full-Duplex)

Slave

Transmit/Receive

(Full-Duplex)

CKE CKP SMP

15 MHz Table 32-42 ——0,10,10,1

10 MHz — Table 32-43 —10,11

10 MHz — Table 32-44 —00,11

15 MHz — — Table 32-45 100

11 MHz — — Table 32-46 110

15 MHz — — Table 32-47 010

11 MHz — — Table 32-48 000

SCKx

(CKP = 0)

SCKx

(CKP = 1)

SDOx

SP10

SP21SP20

SP35

SP20SP21

MSb LSb

Bit 14 - - - - - -1

SP30, SP31

Note: Refer to Figure 32-1 for load conditions.

 2009-2012 Microchip Technology Inc. DS70616G-page 539

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 32-24: SPI2 MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY, CKE = 1) TIMING

CHARACTERISTICS

TABLE 32-42: SPI2 MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY) TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ.(2)Max. Units Conditions

SP10 TscP Maximum SCKx Frequency — — 15 MHz See Note 3

SP20 TscF SCKx Output Fall Time — — — ns See Parameter DO32

and Note 4

SP21 TscR SCKx Output Rise Time — — — ns See Parameter DO31

and Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See Parameter DO32

and Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See Parameter DO31

and Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

—620ns

SP36 TdiV2scH,

TdiV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

3: The minimum clock period for SCKx is 66.7 ns. Therefore, the clock generated in Master mode must not

violate this specification.

4: Assumes 50 pF load on all SPIx pins.

SCKx

(CKP = 0)

SCKx

(CKP = 1)

SDOx

SP21SP20

SP35

SP20SP21

MSb LSb

Bit 14 - - - - - -1

SP30, SP31

Note: Refer to Figure 32-1 for load conditions.

SP36

SP10

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 540  2009-2012 Microchip Technology Inc.

FIGURE 32-25: SPI2 MASTER MODE (FULL-DUPLEX, CKE = 1, CKP = x, SMP = 1) TIMING

CHARACTERISTICS

TABLE 32-43: SPI2 MASTER MODE (FULL-DUPLEX, CKE = 1, CKP = x, SMP = 1) TIMING

REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ.(2)Max. Units Conditions

SP10 TscP Maximum SCKx Frequency — — 10 MHz See Note 3

SP20 TscF SCKx Output Fall Time — — — ns See Parameter DO32

and Note 4

SP21 TscR SCKx Output Rise Time — — — ns See Parameter DO31

and Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See Parameter DO32

and Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See Parameter DO31

and Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

— 6 20 ns

SP36 TdoV2sc,

TdoV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns

SP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data

Input to SCKx Edge

30 — — ns

SP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

30 — — ns

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

3: The minimum clock period for SCKx is 100 ns. The clock generated in Master mode must not violate this

specification.

4: Assumes 50 pF load on all SPIx pins.

SCKx

(CKP = 0)

SCKx

(CKP = 1)

SDOx

SP21SP20

SP20SP21

MSb LSb

Bit 14 - - - - - -1

SP30, SP31

Note: Refer to Figure 32-1 for load conditions.

SP36

SP41

LSb In

Bit 14 - - - -1

SDIx

SP40

SP10

SP35

MSb In

 2009-2012 Microchip Technology Inc. DS70616G-page 541

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 32-26: SPI2 MASTER MODE (FULL-DUPLEX, CKE = 0, CKP = X, SMP = 1) TIMING

CHARACTERISTICS

TABLE 32-44: SPI2 MASTER MODE (FULL-DUPLEX, CKE = 0, CKP = x, SMP = 1) TIMING

REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ.(2)Max. Units Conditions

SP10 TscP Maximum SCKx Frequency — — 10 MHz -40ºC to +125ºC and

see Note 3

SP20 TscF SCKx Output Fall Time — — — ns See Parameter DO32

and Note 4

SP21 TscR SCKx Output Rise Time — — — ns See Parameter DO31

and Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See Parameter DO32

and Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See Parameter DO31

and Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

— 6 20 ns

SP36 TdoV2scH,

TdoV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns

SP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data

Input to SCKx Edge

30 — — ns

SP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

30 — — ns

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ.” column is at 3.3V, +25°C unless otherwise stated.

3: The minimum clock period for SCKx is 100 ns. The clock generated in Master mode must not violate this

specification.

4: Assumes 50 pF load on all SPIx pins.

SCKx

(CKP = 0)

SCKx

(CKP = 1)

SDOx

SDIx

SP40 SP41

SP21

SP20

SP35

SP20SP21

MSb LSb

Bit 14 - - - - - -1

LSb In

Bit 14 - - - -1

SP30, SP31

Note: Refer to Figure 32-1 for load conditions.

SP36

SP10

MSb In

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 542  2009-2012 Microchip Technology Inc.

FIGURE 32-27: SPI2 SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 0, SMP = 0) TIMING

CHARACTERISTICS

SSx

SCKx

(CKP = 0)

SCKx

(CKP = 1)

SDOx

SDIx

SP60

SP30,SP31

MSb Bit 14 - - - - - -1 LSb

SP51

Bit 14 - - - -1 LSb In

SP52

SP73SP72

SP72SP73

SP70

SP40

SP41

Note: Refer to Figure 32-1 for load conditions.

SP36

SP50

SP35

MSb In

 2009-2012 Microchip Technology Inc. DS70616G-page 543

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 32-45: SPI2 SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 0, SMP = 0) TIMING

REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ.(2)Max. Units Conditions

SP70 TscP Maximum SCKx Input Frequency — — 15 MHz See Note 3

SP72 TscF SCKx Input Fall Time — — — ns See Parameter DO32

and Note 4

SP73 TscR SCKx Input Rise Time — — — ns See Parameter DO31

and Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See Parameter DO32

and Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See Parameter DO31

and Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

— 6 20 ns

SP36 TdoV2scH,

TdoV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns

SP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data Input

to SCKx Edge

30 — — ns

SP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

30 — — ns

SP50 TssL2scH,

TssL2scL

SSx  to SCKx  or SCKx 

Input

120 — — ns

SP51 TssH2doZ SSx  to SDOx Output,

High-Impedance

10 — 50 ns See Note 4

SP52 TscH2ssH

TscL2ssH

SSx after SCKx Edge 1.5 TCY + 40 — — ns See Note 4

SP60 TssL2doV SDOx Data Output Valid after

SSx Edge

— — 50 ns

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

3: The minimum clock period for SCKx is 66.7 ns. Therefore, the SCKx clock generated by the master must

not violate this specification.

4: Assumes 50 pF load on all SPIx pins.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 544  2009-2012 Microchip Technology Inc.

FIGURE 32-28: SPI2 SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 1, SMP = 0) TIMING

CHARACTERISTICS

SSx

SCKx

(CKP = 0)

SCKx

(CKP = 1)

SDOx

SDIx

SP50

SP60

SP30,SP31

MSb Bit 14 - - - - - -1 LSb

SP51

Bit 14 - - - -1 LSb In

SP52

SP73SP72

SP72SP73SP70

SP40

SP41

Note: Refer to Figure 32-1 for load conditions.

SP36

SP35

MSb In

 2009-2012 Microchip Technology Inc. DS70616G-page 545

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 32-46: SPI2 SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 1, SMP = 0) TIMING

REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ.(2)Max. Units Conditions

SP70 TscP Maximum SCKx Input Frequency — — 11 MHz See Note 3

SP72 TscF SCKx Input Fall Time — — — ns See Parameter DO32

and Note 4

SP73 TscR SCKx Input Rise Time — — — ns See Parameter DO31

and Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See Parameter DO32

and Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See Parameter DO31

and Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

— 6 20 ns

SP36 TdoV2scH,

TdoV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns

SP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data Input

to SCKx Edge

30 — — ns

SP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

30 — — ns

SP50 TssL2scH,

TssL2scL

SSx  to SCKx  or SCKx 

Input

120 — — ns

SP51 TssH2doZ SSx  to SDOx Output,

High-Impedance

10 — 50 ns See Note 4

SP52 TscH2ssH,

TscL2ssH

SSx after SCKx Edge 1.5 TCY + 40 — — ns See Note 4

SP60 TssL2doV SDOx Data Output Valid after

SSx Edge

— — 50 ns

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

3: The minimum clock period for SCKx is 91 ns. Therefore, the SCKx clock generated by the master must not

violate this specification.

4: Assumes 50 pF load on all SPIx pins.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 546  2009-2012 Microchip Technology Inc.

FIGURE 32-29: SPI2 SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 1, SMP = 0) TIMING

CHARACTERISTICS

SSX

SCKX

(CKP = 0)

SCKX

(CKP = 1)

SDOX

SP50

SP40

SP41

SP30,SP31 SP51

SP35

MSb LSb

Bit 14 - - - - - -1

Bit 14 - - - -1 LSb In

SP52

SP73SP72

SP72SP73

SP70

Note: Refer to Figure 32-1 for load conditions.

SDIXMSb In

SP36

 2009-2012 Microchip Technology Inc. DS70616G-page 547

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 32-47: SPI2 SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 1, SMP = 0) TIMING

REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ.(2)Max. Units Conditions

SP70 TscP Maximum SCKx Input Frequency — — 15 MHz See Note 3

SP72 TscF SCKx Input Fall Time — — — ns See Parameter DO32

and Note 4

SP73 TscR SCKx Input Rise Time — — — ns See Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

— 6 20 ns

SP36 TdoV2scH,

TdoV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns

SP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data Input

to SCKx Edge

30 — — ns

SP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

30 — — ns

SP50 TssL2scH,

TssL2scL

SSx  to SCKx  or SCKx 

Input

120 — — ns

SP51 TssH2doZ SSx  to SDOx Output,

High-Impedance

10 — 50 ns See Note 4

SP52 TscH2ssH,

TscL2ssH

SSx after SCKx Edge 1.5 TCY + 40 — — ns See Note 4

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

3: The minimum clock period for SCKx is 66.7 ns. Therefore, the SCKx clock generated by the master must

not violate this specification.

4: Assumes 50 pF load on all SPIx pins.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 548  2009-2012 Microchip Technology Inc.

FIGURE 32-30: SPI2 SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 0, SMP = 0) TIMING

CHARACTERISTICS

SSX

SCKX

(CKP = 0)

SCKX

(CKP = 1)

SDOX

SP50

SP40

SP41

SP30,SP31 SP51

SP35

MSb LSb

Bit 14 - - - - - -1

Bit 14 - - - -1 LSb In

SP52

SP73SP72

SP72SP73

SP70

Note: Refer to Figure 32-1 for load conditions.

SDIX

SP36

MSb In

 2009-2012 Microchip Technology Inc. DS70616G-page 549

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 32-48: SPI2 SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 0, SMP = 0) TIMING

REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ.(2)Max. Units Conditions

SP70 TscP Maximum SCKx Input Frequency — — 11 MHz See Note 3

SP72 TscF SCKx Input Fall Time — — — ns See Parameter DO32

and Note 4

SP73 TscR SCKx Input Rise Time — — — ns See Parameter DO31

and Note 4

SP30 TdoF SDOx Data Output Fall Time — — — ns See Parameter DO32

and Note 4

SP31 TdoR SDOx Data Output Rise Time — — — ns See Parameter DO31

and Note 4

SP35 TscH2doV,

TscL2doV

SDOx Data Output Valid after

SCKx Edge

— 6 20 ns

SP36 TdoV2scH,

TdoV2scL

SDOx Data Output Setup to

First SCKx Edge

30 — — ns

SP40 TdiV2scH,

TdiV2scL

Setup Time of SDIx Data Input

to SCKx Edge

30 — — ns

SP41 TscH2diL,

TscL2diL

Hold Time of SDIx Data Input

to SCKx Edge

30 — — ns

SP50 TssL2scH,

TssL2scL

SSx  to SCKx  or SCKx 

Input

120 — — ns

SP51 TssH2doZ SSx  to SDOx Output,

High-Impedance

10 — 50 ns See Note 4

SP52 TscH2ssH,

TscL2ssH

SSx after SCKx Edge 1.5 TCY + 40 — — ns See Note 4

Note 1: These parameters are characterized, but are not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.

3: The minimum clock period for SCKx is 91 ns. Therefore, the SCKx clock generated by the master must not

violate this specification.

4: Assumes 50 pF load on all SPIx pins.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 550  2009-2012 Microchip Technology Inc.

FIGURE 32-31: I2Cx BUS START/STOP BITS TIMING CHARACTERISTICS (MASTER MODE)

FIGURE 32-32: I2Cx BUS DATA TIMING CHARACTERISTICS (MASTER MODE)

SCLx

SDAx

Start

Condition

Stop

Condition

Note: Refer to Figure 32-1 for load conditions.

IM30

IM31 IM34

IM33

IM30 IM31 IM33

IM11

IM10

IM20

IM26

IM25

IM40 IM40 IM45

IM21

SCLx

SDAx

Out

Note: Refer to Figure 32-1 for load conditions.

 2009-2012 Microchip Technology Inc. DS70616G-page 551

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 32-49: I2Cx BUS DATA TIMING REQUIREMENTS (MASTER MODE)

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Symbol Characteristic(4)Min.(1)Max. Units Conditions

IM10 TLO:SCL Clock Low Time 100 kHz mode TCY/2 (BRG + 2) — s

400 kHz mode TCY/2 (BRG + 2) — s

1 MHz mode(2)TCY/2 (BRG + 2) — s

IM11 THI:SCL Clock High Time 100 kHz mode TCY/2 (BRG + 2) — s

400 kHz mode TCY/2 (BRG + 2) — s

1 MHz mode(2)TCY/2 (BRG + 2) — s

IM20 TF:SCL SDAx and SCLx

Fall Time

100 kHz mode — 300 ns CB is specified to be

from 10 to 400 pF

400 kHz mode 20 + 0.1 CB300 ns

1 MHz mode(2)— 100 ns

IM21 TR:SCL SDAx and SCLx

Rise Time

100 kHz mode — 1000 ns CB is specified to be

from 10 to 400 pF

400 kHz mode 20 + 0.1 CB300 ns

1 MHz mode(2)— 300 ns

IM25 TSU:DAT Data Input

Setup Time

100 kHz mode 250 — ns

400 kHz mode 100 — ns

1 MHz mode(2)40 — ns

IM26 THD:DAT Data Input

Hold Time

100 kHz mode 0 — s

400 kHz mode 0 0.9 s

1 MHz mode(2)0.2 — s

IM30 TSU:STA Start Condition

Setup Time

100 kHz mode TCY/2 (BRG + 2) — s Only relevant for

Repeated Start

condition

400 kHz mode TCY/2 (BRG + 2) — s

1 MHz mode(2)TCY/2 (BRG + 2) — s

IM31 THD:STA Start Condition

Hold Time

100 kHz mode TCY/2 (BRG + 2) — s After this period, the

first clock pulse is

generated

400 kHz mode TCY/2 (BRG +2) — s

1 MHz mode(2)TCY/2 (BRG + 2) — s

IM33 TSU:STO Stop Condition

Setup Time

100 kHz mode TCY/2 (BRG + 2) — s

400 kHz mode TCY/2 (BRG + 2) — s

1 MHz mode(2)TCY/2 (BRG + 2) — s

IM34 THD:STO Stop Condition 100 kHz mode TCY/2 (BRG + 2) — s

Hold Time 400 kHz mode TCY/2 (BRG + 2) — s

1 MHz mode(2)TCY/2 (BRG + 2) — s

IM40 TAA:SCL Output Valid

From Clock

100 kHz mode — 3500 ns

400 kHz mode — 1000 ns

1 MHz mode(2)— 400 ns

IM45 TBF:SDA Bus Free Time 100 kHz mode 4.7 — s Time the bus must be

free before a new

transmission can start

400 kHz mode 1.3 — s

1 MHz mode(2)0.5 — s

IM50 CBBus Capacitive Loading — 400 pF

IM51 TPGD Pulse Gobbler Delay 65 390 ns See Note 3

Note 1: BRG is the value of the I2C Baud Rate Generator. Refer to Section 19. “Inter-Integrated Circuit (I2C™)”

(DS70330) in the “dsPIC33E/PIC24E Family Reference Manual”. Please see the Microchip web site for

the latest family reference manual sections.

2: Maximum pin capacitance = 10 pF for all I2Cx pins (for 1 MHz mode only).

3: Typical value for this parameter is 130 ns.

4: These parameters are characterized, but not tested in manufacturing.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 552  2009-2012 Microchip Technology Inc.

FIGURE 32-33: I2Cx BUS START/STOP BITS TIMING CHARACTERISTICS (SLAVE MODE)

FIGURE 32-34: I2Cx BUS DATA TIMING CHARACTERISTICS (SLAVE MODE)

SCLx

SDAx

Start

Condition

Stop

Condition

IS34

IS33

IS30

IS31

IS30 IS31 IS33

IS11

IS10

IS20

IS25

IS40 IS40 IS45

IS21

SCLx

SDAx

Out

IS26

 2009-2012 Microchip Technology Inc. DS70616G-page 553

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 32-50: I2Cx BUS DATA TIMING REQUIREMENTS (SLAVE MODE)

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  T

A  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Symbol Characteristic(3)Min. Max. Units Conditions

IS10 TLO:SCL Clock Low Time 100 kHz mode 4.7 — s

400 kHz mode 1.3 — s

1 MHz mode(1)0.5 — s

IS11 THI:SCL Clock High Time 100 kHz mode 4.0 — s Device must operate at a

minimum of 1.5 MHz

400 kHz mode 0.6 — s Device must operate at a

minimum of 10 MHz

1 MHz mode(1)0.5 — s

IS20 TF:SCL SDAx and SCLx

Fall Time

100 kHz mode — 300 ns CB is specified to be from

10 to 400 pF

400 kHz mode 20 + 0.1 CB300 ns

1 MHz mode(1)—100ns

IS21 TR:SCL SDAx and SCLx

Rise Time

100 kHz mode — 1000 ns CB is specified to be from

10 to 400 pF

400 kHz mode 20 + 0.1 CB300 ns

1 MHz mode(1)—300ns

IS25 TSU:DAT Data Input

Setup Time

100 kHz mode 250 — ns

400 kHz mode 100 — ns

1 MHz mode(1)100 — ns

IS26 THD:DAT Data Input

Hold Time

100 kHz mode 0 — s

400 kHz mode 0 0.9 s

1 MHz mode(1)00.3s

IS30 TSU:STA Start Condition

Setup Time

100 kHz mode 4.7 — s Only relevant for Repeated

Start condition

400 kHz mode 0.6 — s

1 MHz mode(1)0.25 — s

IS31 THD:STA Start Condition

Hold Time

100 kHz mode 4.0 — s After this period, the first

clock pulse is generated

400 kHz mode 0.6 — s

1 MHz mode(1)0.25 — s

IS33 TSU:STO Stop Condition

Setup Time

100 kHz mode 4.7 — s

400 kHz mode 0.6 — s

1 MHz mode(1)0.6 — s

IS34 THD:STO Stop Condition

Hold Time

100 kHz mode 4 — s

400 kHz mode 0.6 — s

1 MHz mode(1)0.25 s

IS40 TAA:SCL Output Valid

From Clock

100 kHz mode 0 3500 ns

400 kHz mode 0 1000 ns

1 MHz mode(1)0350ns

IS45 TBF:SDA Bus Free Time 100 kHz mode 4.7 — s Time the bus must be free

before a new transmission

can start

400 kHz mode 1.3 — s

1 MHz mode(1)0.5 — s

IS50 CBBus Capacitive Loading — 400 pF

IS51 TPGD Pulse Gobbler Delay 65 390 ns See Note 2

Note 1: Maximum pin capacitance = 10 pF for all I2Cx pins (for 1 MHz mode only).

2: The typical value for this parameter is 130 ns.

3: These parameters are characterized, but not tested in manufacturing.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 554  2009-2012 Microchip Technology Inc.

FIGURE 32-35: ECAN™ MODULE I/O TIMING CHARACTERISTICS

TABLE 32-51: ECAN™ MODULE I/O TIMING REQUIREMENTS

FIGURE 32-36: UARTx MODULE I/O TIMING CHARACTERISTICS

TABLE 32-52: UARTx MODULE I/O TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ.(2)Max. Units Conditions

CA10 TioF Port Output Fall Time — — — ns See Parameter DO32

CA11 TioR Port Output Rise Time — — — ns See Parameter DO31

CA20 TCWF Pulse Width to Trigger

CAN Wake-up Filter

120 — — ns

Note 1: These parameters are characterized but not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only

and are not tested.

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +125°C

Param. Symbol Characteristic(1)Min. Typ.(2)Max. Units Conditions

UA10 TUABAUD UARTx Baud Time 66.67 — — ns

UA11 FBAUD UARTx Baud Frequency — — 15 mbps

UA20 TCWF Start Bit Pulse Width to Trigger

UARTx Wake-up

500 — — ns

Note 1: These parameters are characterized but not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only

and are not tested.

CxTx Pin

(output)

CA10 CA11

Old Value New Value

CA20

CxRx Pin

(input)

UA20

UxRX MSb In LSb In

Bit 6-1

UA10

UXTX

 2009-2012 Microchip Technology Inc. DS70616G-page 555

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 32-53: USB OTG MODULE SPECIFICATIONS

(dsPIC33EPXXXMU8XX AND PIC24EPXXXGU8XX DEVICES ONLY)

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  T

A  +85°C for Industrial

-40°C T

A +125°C for Extended

Param. Symbol Characteristics(1)Min. Typ. Max. Units Conditions

USB313 VUSB3V3(2)USB Voltage 3.0 — 3.6 V Voltage on bus must be in this

range for proper USB operation

USB315 VILUSB Input Low Voltage for USB

Buffer

——0.8V

USB316 VIHUSB Input High Voltage for USB

Buffer

2.0 — — V

USB318 VDIFS Differential Input Sensitivity — — 0.2 V

USB319 VCM Differential Common-Mode

Range

0.8 — 2.5 V The difference between D+ and

D- must be within this range

while VCM is met

USB320 ZOUT Driver Output Impedance 28.0 — 44.0 

USB321 VOL Voltage Output Low 0.0 — 0.3 V 14.25 k load connected to

3.6V

USB322 VOH Voltage Output High 2.8 — 3.6 V 14.25 k load connected to

ground

Note 1: These parameters are characterized but not tested in manufacturing.

2: If the USB module is not being used, this pin must be connected to VDD.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 556  2009-2012 Microchip Technology Inc.

TABLE 32-54: ADC MODULE SPECIFICATIONS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (see Note 3)

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic Min. Typ. Max. Units Conditions

Device Supply

AD01 AVDD(2)Module VDD Supply Greater of

VDD – 0.3

or 3.0

— Lesser of

VDD + 0.3

or 3.6

AD02 AVSS Module VSS Supply VSS – 0.3 — VSS + 0.3 V

Reference Inputs

AD05 VREFH Reference Voltage High AVSS + 2.5 — AVDD VSee Note 1,

VREFH = VREF+,

VREFL = VREF-

AD05a 3.0 — 3.6 V VREFH = AVDD,

VREFL = AVSS = 0

AD06 VREFL Reference Voltage Low AVSS —AVDD – 2.5 V See Note 1

AD06a 0 — 0 V VREFH = AVDD,

VREFL = AVSS = 0

AD07 VREF Absolute Reference

Voltage

2.5 — 3.6 V VREF = VREFH – VREFL

AD08 IREF Current Drain —

—

600

A

ADC off

ADC on

AD09 IAD Operating Current —

—

9.0

3.2

—

ADC operating in 10-bit

mode, see Note 1

ADC operating in 12-bit

mode, see Note 1

Analog Input

AD12 VINH Input Voltage Range, VINH VINL —VREFH V This voltage reflects Sample

& Hold Channels 0, 1, 2 and 3

(CH0-CH3), positive input

AD13 VINL Input Voltage Range, VINL VREFL —AVSS + 1V V This voltage reflects Sample

& Hold Channels 0, 1, 2 and 3

(CH0-CH3), negative input

AD17 RIN Recommended Impedance

of Analog Voltage Source

——200

Note 1: These parameters are not characterized or tested in manufacturing.

2: The voltage difference between AVDD and VDD cannot exceed 300 mV at any time during operation or start-up.

3: Device is functional at VBORMIN < VDD < VDDMIN. Analog modules: ADC, Comparator and DAC will have

degraded performance. Device functionality is tested but not characterized. Refer to Parameter BO10 in

Table 32-11 for the minimum and maximum BOR values.

 2009-2012 Microchip Technology Inc. DS70616G-page 557

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 32-55: ADC MODULE SPECIFICATIONS (12-BIT MODE)

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (see Note 1)

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C T

A +125°C for Extended

Param. Symbol Characteristic Min. Typ. Max. Units Conditions

ADC Accuracy (12-Bit Mode) – Measurements with External VREF+/VREF-

AD20a Nr Resolution 12 Data Bits bits

AD21a INL Integral Nonlinearity -2 — +2 LSb VINL = AVSS = VREFL = 0V,

AVDD = VREFH = 3.6V

AD22a DNL Differential Nonlinearity >-1 — <1 LSb VINL = AVSS = VREFL = 0V,

AVDD = VREFH = 3.6V

AD23a GERR Gain Error 1.25 1.5 3 LSb VINL = AVSS = VREFL = 0V,

AVDD = VREFH = 3.6V

AD24a EOFF Offset Error 1.25 1.52 2 LSb VINL = AVSS = VREFL = 0V,

AVDD = VREFH = 3.6V

AD25a — Monotonicity — — — — Guaranteed(2)

ADC Accuracy (12-Bit Mode) – Measurements with Internal VREF+/VREF-

AD20a Nr Resolution 12 data bits bits

AD21a INL Integral Nonlinearity -2 — +2 LSb VINL = AVSS = 0V, AVDD = 3.6V

AD22a DNL Differential Nonlinearity >-1 — <1 LSb VINL = AVSS = 0V, AVDD = 3.6V

AD23a GERR Gain Error 2 3 7 LSb VINL = AVSS = 0V, AVDD = 3.6V

AD24a EOFF Offset Error 2 3 5 LSb VINL = AVSS = 0V, AVDD = 3.6V

AD25a — Monotonicity — — — — Guaranteed(2)

Dynamic Performance (12-Bit Mode)

AD30a THD Total Harmonic Distortion — — -75 dB

AD31a SINAD Signal to Noise and

Distortion

68.5 69.5 — dB

AD32a SFDR Spurious Free Dynamic

Range

80 — — dB

AD33a FNYQ Input Signal Bandwidth — — 250 kHz

AD34a ENOB Effective Number of Bits 11.09 11.3 — bits

Note 1: Device is functional at VBORMIN < VDD < VDDMIN. Analog modules: ADC, Comparator and DAC will have

degraded performance. Device functionality is tested but not characterized. Refer to Parameter BO10 in

Table 32-11 for the minimum and maximum BOR values.

2: The Analog-to-Digital conversion result never decreases with an increase in input voltage and has no

missing codes.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 558  2009-2012 Microchip Technology Inc.

TABLE 32-56: ADC MODULE SPECIFICATIONS (10-BIT MODE)

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (see Note 1)

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C T

A +125°C for Extended

Param. Symbol Characteristic Min. Typ. Max. Units Conditions

ADC Accuracy (10-Bit Mode) – Measurements with External VREF+/VREF-

AD20b Nr Resolution 10 data bits bits

AD21b INL Integral Nonlinearity -1 — +1 LSb VINL = AVSS = VREFL = 0V,

AVDD = VREFH = 3.6V

AD22b DNL Differential Nonlinearity >-1 — <1 LSb VINL = AVSS = VREFL = 0V,

AVDD = VREFH = 3.6V

AD23b GERR Gain Error 1 3 6 LSb VINL = AVSS = VREFL = 0V,

AVDD = VREFH = 3.6V

AD24b EOFF Offset Error 1 2 3 LSb VINL = AVSS = VREFL = 0V,

AVDD = VREFH = 3.6V

AD25b — Monotonicity — — — — Guaranteed(2)

ADC Accuracy (10-Bit Mode) – Measurements with Internal VREF+/VREF-

AD20b Nr Resolution 10 data bits bits

AD21b INL Integral Nonlinearity -1.5 — +1.5 LSb VINL = AVSS = 0V, AVDD = 3.6V

AD22b DNL Differential Nonlinearity >-1 — <1 LSb VINL = AVSS = 0V, AVDD = 3.6V

AD23b GERR Gain Error 1 5 6 LSb VINL = AVSS = 0V, AVDD = 3.6V

AD24b EOFF Offset Error 1 2 5 LSb VINL = AVSS = 0V, AVDD = 3.6V

AD25b — Monotonicity — — — — Guaranteed(2)

Dynamic Performance (10-Bit Mode)

AD30b THD Total Harmonic Distortion — — -64 dB

AD31b SINAD Signal to Noise and

Distortion

57 58.5 — dB

AD32b SFDR Spurious Free Dynamic

Range

72 — — dB

AD33b FNYQ Input Signal Bandwidth — — 550 kHz

AD34b ENOB Effective Number of Bits 9.16 9.4 — bits

Note 1: Device is functional at VBORMIN < VDD < VDDMIN. Analog modules: ADC, Comparator and DAC will have

degraded performance. Device functionality is tested but not characterized. Refer to Parameter BO10 in

Table 32-11 for the minimum and maximum BOR values.

2: The Analog-to-Digital conversion result never decreases with an increase in input voltage and has no

missing codes.

 2009-2012 Microchip Technology Inc. DS70616G-page 559

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 32-37: ADC CONVERSION (12-BIT MODE) TIMING CHARACTERISTICS

(ASAM = 0, SSRC<2:0> = 000, SSRCG = 0)

AD55

TSAMP

Set SAMP

AD61

ADCLK

Instruction

SAMP

AD60

DONE

AD1IF

1 2 3 4 5 6 87

1– Software sets AD1CON1. SAMP to start sampling.

2– Sampling starts after discharge period. TSAMP is described in

3– Software clears AD1CON1. SAMP to start conversion.

4– Sampling ends, conversion sequence starts.

5– Convert bit 11.

9– One TAD for end of conversion.

AD50

6– Convert bit 10.

7– Convert bit 1.

8– Convert bit 0.

Execution

“dsPIC33E/PIC24E Family Reference Manual”.

Section 16. “Analog-to-Digital Converter (ADC)” (DS70621) of the

Clear SAMP

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 560  2009-2012 Microchip Technology Inc.

TABLE 32-57: ADC CONVERSION (12-BIT MODE) TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (see Note 4)

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Symbol Characteristic Min. Typ.(2)Max. Units Conditions

Clock Parameters

AD50 TAD ADC Clock Period 117.6 — — ns

AD51 tRC ADC Internal RC Oscillator

Period

— 250 — ns

Conversion Rate

AD55 tCONV Conversion Time — 14 TAD ns

AD56 FCNV Throughput Rate — — 500 Ksps

AD57 TSAMP Sample Time 3 TAD —— —

Timing Parameters

AD60 tPCS Conversion Start from Sample

Trigger(1)

2 TAD —3 TAD — Auto-Convert Trigger

not selected

AD61 tPSS Sample Start from Setting

Sample (SAMP) bit(1)

2 TAD —3 TAD —

AD62 tCSS Conversion Completion to

Sample Start (ASAM = 1)(1)

— 0.5 TAD ——

AD63 tDPU Time to Stabilize Analog Stage

from ADC Off to ADC On(1)

——20sSee Note 3

Note 1: Because the sample caps will eventually lose charge, clock rates below 10 kHz may affect linearity

performance, especially at elevated temperatures.

2: These parameters are characterized but not tested in manufacturing.

3: The tDPU parameter is the time required for the ADC module to stabilize at the appropriate level when the

module is turned on (ADON (ADxCON1<15>) = 1). During this time, the ADC result is indeterminate.

4: Device is functional at VBORMIN < VDD < VDDMIN. Analog modules: ADC, Comparator and DAC will have

degraded performance. Device functionality is tested but not characterized. Refer to Parameter BO10 in

Table 32-11 for the minimum and maximum BOR values.

 2009-2012 Microchip Technology Inc. DS70616G-page 561

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 32-38: ADC CONVERSION (10-BIT MODE) TIMING CHARACTERISTICS

(CHPS<1:0> = 01, SIMSAM = 0, ASAM = 0, SSRC<2:0> = 000, SSRCG = 0)

FIGURE 32-39: ADC CONVERSION (10-BIT MODE) TIMING CHARACTERISTICS (CHPS<1:0> = 01,

SIMSAM = 0, ASAM = 1, SSRC<2:0> = 111, SSRCG = 0, SAMC<4:0> = 00010)

TSAMP

Set SAMP

AD61

ADCLK

Instruction

SAMP

AD60

DONE

ADxIF

1 2 3 4 5 6 8 5 6 7

1– Software sets ADx1CON1. SAMP to start sampling.

2– Sampling starts after discharge period. TSAMP is described in

3– Software clears ADxCON1. SAMP to start conversion.

4– Sampling ends, conversion sequence starts.

5– Convert bit 9.

8– One TAD for end of conversion.

AD50

7 8

6– Convert bit 8.

7– Convert bit 0.

Execution

“dsPIC33E/PIC24E Family Reference Manual”.

Section 16. “Analog-to-Digital Converter (ADC)” (DS70621) of the

AD55

Clear SAMP

1 2 3 4 5 6 4 5 6 8

1– Software sets ADxCON1. ADON to start AD operation.

2– Sampling starts after discharge period. TSAMP is described in

3– Convert bit 9.

4– Convert bit 8.

5– Convert bit 0.

7 3

6– One TAD for end of conversion.

7– Begin conversion of next channel.

8– Sample for time specified by SAMC<4:0>.

ADCLK

Instruction Set ADON

Execution

SAMP

TSAMP

ADxIF

DONE

AD55 AD55 TSAMP AD55

AD50

Section 16. “Analog-to-Digital Converter (ADC)” (DS70621)

of the “dsPIC33E/PIC24E Family Reference Manual”.

AD62

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 562  2009-2012 Microchip Technology Inc.

TABLE 32-58: ADC CONVERSION (10-BIT MODE) TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (see Note 4)

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Symbol Characteristic Min. Typ.(1)Max. Units Conditions

Clock Parameters

AD50 TAD ADC Clock Period 76 — — ns

AD51 tRC ADC Internal RC Oscillator Period — 250 — ns

Conversion Rate

AD55 tCONV Conversion Time — 12 TAD ——

AD56 FCNV Throughput Rate — — 1.1 Msps Using sequential

sampling

AD57 TSAMP Sample Time 2 TAD ———

Timing Parameters

AD60 tPCS Conversion Start from Sample

Trigger(2)

2 TAD —3 TAD — Auto-Convert Trigger

not selected

AD61 tPSS Sample Start from Setting

Sample (SAMP) bit(2)

2 TAD —3 TAD —

AD62 tCSS Conversion Completion to

Sample Start (ASAM = 1)(2)

— 0.5 TAD ——

AD63 tDPU Time to Stabilize Analog Stage

from ADC Off to ADC On(2)

——20s See Note 3

Note 1: These parameters are characterized but not tested in manufacturing.

2: Because the sample caps will eventually lose charge, clock rates below 10 kHz may affect linearity

performance, especially at elevated temperatures.

3: The tDPU parameter is the time required for the ADC module to stabilize at the appropriate level when the

module is turned on (ADON (ADxCON1<15>) = 1). During this time, the ADC result is indeterminate.

4: Device is functional at VBORMIN < VDD < VDDMIN. Analog modules: ADC, Comparator and DAC will have

degraded performance. Device functionality is tested but not characterized. Refer to Parameter BO10 in

Table 32-11 for the minimum and maximum BOR values.

 2009-2012 Microchip Technology Inc. DS70616G-page 563

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 32-40: DCI MODULE (MULTI-CHANNEL, I2S MODES) TIMING CHARACTERISTICS

COFS

CSCK

(SCKE = 0)

CSCK

(SCKE = 1)

CSDO

CSDI

CS11 CS10

CS40 CS41

CS21CS20

CS35

CS21

MSb LSb

LSb In

CS31

High-Z High-Z

CS30

CS51 CS50

Note: Refer to Figure 32-1 for load conditions.

CS20

CS56

CS55

MSb In

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 564  2009-2012 Microchip Technology Inc.

TABLE 32-59: DCI MODULE (MULTI-CHANNEL, I2S MODES) TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ.(2)Max. Units Conditions

CS10 TCSCKL CSCK Input Low Time

(CSCK pin is an input)

TCY/2 + 20 — — ns

CSCK Output Low Time(3)

(CSCK pin is an output)

30 — — ns

CS11 TCSCKH CSCK Input High Time

(CSCK pin is an input)

TCY/2 + 20 — — ns

CSCK Output High Time(3)

(CSCK pin is an output)

30 — — ns

CS20 TCSCKF CSCK Output Fall Time

(CSCK pin is an output)

— — — ns See Parameter DO32

CS21 TCSCKR CSCK Output Rise Time

(CSCK pin is an output)

— — — ns See Parameter DO31

CS30 TCSDOF CSDO Data Output Fall Time — — — ns See Parameter DO32

CS31 TCSDOR CSDO Data Output Rise Time — — — ns See Parameter DO31

CS35 TDV Clock Edge to CSDO Data Valid — — 10 ns

CS36 TDIV Clock Edge to CSDO Tri-Stated 10 — 20 ns

CS40 TCSDI Setup Time of CSDI Data Input

to CSCK Edge (CSCK pin is

input or output)

20 — — ns

CS41 THCSDI Hold Time of CSDI Data Input to

CSCK Edge (CSCK pin is input

or output)

20 — — ns

CS50 TCOFSF COFS Fall Time

(COFS pin is output)

— — — ns See Parameter DO32

CS51 TCOFSR COFS Rise Time

(COFS pin is output)

— — — ns See Parameter DO31

CS55 TSCOFS Setup Time of COFS Data Input

to CSCK Edge (COFS pin is

input)

20 — — ns

CS56 THCOFS Hold Time of COFS Data Input to

CSCK Edge (COFS pin is input)

20 — — ns

Note 1: These parameters are characterized but not tested in manufacturing.

2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only

and are not tested.

3: The minimum clock period for CSCK is 100 ns. Therefore, the clock generated in Master mode must not

violate this specification.

 2009-2012 Microchip Technology Inc. DS70616G-page 565

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 32-41: DCI MODULE (AC-LINK MODE) TIMING CHARACTERISTICS

SYNC

BIT_CLK

SDOx

SDIx

CS61 CS60

CS65 CS66

CS80

CS21

MSb In

CS75

LSb

CS76

(COFS)

(CSCK)

LSb

MSb

CS72

CS71 CS70

CS76 CS75

(CSDO)

(CSDI)

CS62 CS20

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 566  2009-2012 Microchip Technology Inc.

TABLE 32-60: DCI MODULE (AC-LINK MODE) TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C  TA  +125°C for Extended

Param. Symbol Characteristic(1,2)Min. Typ.(3)Max. Units Conditions

CS60 TBCLKL BIT_CLK Low Time 36 40.7 45 ns

CS61 TBCLKH BIT_CLK High Time 36 40.7 45 ns

CS62 TBCLK BIT_CLK Period — 81.4 — ns Bit clock is input

CS65 TSACL Input Setup Time to

Falling Edge of BIT_CLK

— — 10 ns

CS66 THACL Input Hold Time from

Falling Edge of BIT_CLK

— — 10 ns

CS70 TSYNCLO Sync Data Output Low Time — 19.5 — s

CS71 TSYNCHI Sync Data Output High Time — 1.3 — s

CS72 TSYNC Sync Data Output Period — 20.8 — s

CS77 TRACL Rise Time, Sync, SDATA_OUT — — — ns See Parameter DO32

CS78 TFACL Fall Time, Sync, SDATA_OUT — — — ns See Parameter DO31

CS80 TOVDACL Output Valid Delay from Rising

Edge of BIT_CLK

— — 15 ns

Note 1: These parameters are characterized but not tested in manufacturing.

2: These values assume the BIT_CLK frequency is 12.288 MHz.

3: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only

and are not tested.

 2009-2012 Microchip Technology Inc. DS70616G-page 567

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

TABLE 32-61: COMPARATOR TIMING SPECIFICATIONS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (see Note 3)

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C T

A +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ. Max. Units Conditions

300 TRESP Response Time(2)— 150 400 ns

301 TMC2OV Comparator Mode Change

to Output Valid

——10s

Note 1: Parameters are characterized but not tested.

2: Response time is measured with one comparator input at (VDD – 1.5)/2, while the other input transitions

from VSS to VDD.

3: Device is functional at VBORMIN < VDD < VDDMIN. Analog modules: ADC, Comparator and DAC will have

degraded performance. Device functionality is tested but not characterized. Refer to Parameter BO10 in

Table 32-11 for the minimum and maximum BOR values.

TABLE 32-62: COMPARATOR MODULE SPECIFICATIONS

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (see Note 2)

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ. Max. Units Conditions

D300 VIOFF Input Offset Voltage — ±10 — mV

D301 VICM Input Common-Mode Voltage AVSS —AVDD V

D302 CMRR Common-Mode Rejection Ratio -54 — — dB

D305 IVREF Internal Voltage Reference 0.19 0.20 0.21 V BGSEL<1:0> = 10

0.57 0.60 0.63 V BGSEL<1:0> = 01

1.14 1.20 1.26 V BGSEL<1:0> = 00

Note 1: Parameters are characterized but not tested.

2: Device is functional at VBORMIN < VDD < VDDMIN. Analog modules: ADC, Comparator and DAC will have

degraded performance. Device functionality is tested but not characterized. Refer to Parameter BO10 in

Table 32-11 for the minimum and maximum BOR values.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 568  2009-2012 Microchip Technology Inc.

TABLE 32-63: COMPARATOR REFERENCE VOLTAGE SETTLING TIME SPECIFICATIONS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (see Note 3)

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(2)Min. Typ. Max. Units Conditions

VR310 TSET Settling Time(1)——10s

Note 1: Setting time measured while CVRR = 1 and CVR<3:0> bits transition from ‘0000’ to ‘1111’.

2: These parameters are characterized, but not tested in manufacturing.

3: Device is functional at VBORMIN < VDD < VDDMIN. Analog modules: ADC, Comparator and DAC will have

degraded performance. Device functionality is tested but not characterized. Refer to Parameter BO10 in

Table 32-11 for the minimum and maximum BOR values.

TABLE 32-64: COMPARATOR REFERENCE VOLTAGE SPECIFICATIONS

DC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V (see Note 2)

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ. Max. Units Conditions

VRD310 CVRES Resolution CVRSRC/24 — CVRSRC/32 LSb

VRD311 CVRAA Absolute Accuracy — — 0.5 LSb

VRD312 CVRLMaximum Load on CVREF

Output Pin

——0.75AAVDD = 3.6V,

CVRSS = 0,

CVRR = 0,

CVR<3:0> = 1111

Note 1: These parameters are characterized, but not tested in manufacturing.

2: Device is functional at VBORMIN < VDD < VDDMIN. Analog modules: ADC, Comparator and DAC will have

degraded performance. Device functionality is tested but not characterized. Refer to Parameter BO10 in

Table 32-11 for the minimum and maximum BOR values.

 2009-2012 Microchip Technology Inc. DS70616G-page 569

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 32-42: PARALLEL SLAVE PORT TIMING

PMD<7:0>

PS1

PS2

PS3

PS4

PS5

PS6

PS7

TABLE 32-65: PARALLEL SLAVE PORT TIMING SPECIFICATIONS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Symbol Characteristic(1)Min. Typ. Max. Units Conditions

PS1 TdtV2wrH Data In Valid Before WR or CS

Inactive (setup time)

20 — — ns

PS2 TwrH2dtI WR or CS Inactive to Data In

Invalid (hold time)

20 — — ns

PS3 TrdL2dtV RD and CS to Active Data Out

Valid

— — 80 ns

PS4 TrdH2dtI RD or CS Inactive to Data Out

Invalid

10 — 30 ns

PS5 Tcs CS Active Time 33.33 — — ns

PS6 Twr RD Active Time 33.33 — — ns

PS7 Trd WR Active Time 33.33 — — ns

Note 1: These parameters are characterized, but not tested in manufacturing.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 570  2009-2012 Microchip Technology Inc.

FIGURE 32-43: PARALLEL MASTER PORT READ TIMING DIAGRAM

P1 P2 P3 P4 P1 P2 P3 P4 P1 P2

System

PMA<13:8>

PMD<7:0>

Clock

PMRD

PMALL/PMALH

PMCS1

Address

Address <7:0> Data

PM2 PM6 PM7

PMWR

PM3

PM1

PM5

TABLE 32-66: PARALLEL MASTER PORT READ TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Characteristic(1)Min. Typ. Max. Units Conditions

PM1 PMALL/PMALH Pulse Width — 0.5 TCY —ns

PM2 Address Out Valid to PMALL/PMALH Invalid

(address setup time)

—1 T

CY —ns

PM3 PMALL/PMALH Invalid to Address Out Invalid

(address hold time)

— 0.5 TCY —ns

PM5 PMRD Pulse Width — 0.5 TCY —ns

PM6 PMRD or PMENB Active to Data In Valid (data

setup time)

150 — — ns

PM7 PMRD or PMENB Inactive to Data In Invalid

(data hold time)

——5ns

Note 1: These parameters are characterized, but not tested in manufacturing.

 2009-2012 Microchip Technology Inc. DS70616G-page 571

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 32-44: PARALLEL MASTER PORT WRITE TIMING DIAGRAM

P1 P2 P3 P4 P1 P2 P3 P4 P1 P2

System

PMA<13:8>

PMD<7:0>

Clock

PMWR

PMALL/PMALH

PMCS1

Address

Address <7:0> Data

PM12

PM13

PM16

Data

PMRD

PM11

TABLE 32-67: PARALLEL MASTER PORT WRITE TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Characteristic(1)Min. Typ. Max. Units Conditions

PM11 PMWR Pulse Width — 0.5 TCY —ns

PM12 Data Out Valid Before PMWR or PMENB

goes Inactive (data setup time)

—1 T

CY —ns

PM13 PMWR or PMEMB Invalid to Data Out Invalid

(data hold time)

— 0.5 TCY —ns

PM16 PMCSx Pulse Width TCY - 5 — — ns ADRMUX<1:0> = 00

(demultiplexed

address)

Note 1: These parameters are characterized, but not tested in manufacturing.

TABLE 32-68: DMA MODULE TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature -40°C  TA  +85°C for Industrial

-40°C TA +125°C for Extended

Param. Characteristic(1)Min. Typ. Max. Units Conditions

DM1 DMA Byte/Word Transfer Latency 1 TCY ——ns

Note 1: These parameters are characterized, but not tested in manufacturing.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 572  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 573

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

33.0 DC AND AC DEVICE CHARACTERISTICS GRAPHS

FIGURE 33-1: VOH – 4x DRIVER PINS @ +85ºC

FIGURE 33-2: VOH – 8x DRIVER PINS @ +85ºC

FIGURE 33-3: VOL – 4x DRIVER PINS @ +85ºC

FIGURE 33-4: VOL – 8x DRIVER PINS @ +85ºC

Note: The graphs provided following this note are a statistical summary based on a limited number of samples and are provided for design guidance purposes

only. The performance characteristics listed herein are not tested or guaranteed. In some graphs, the data presented may be outside the specified operating

range (e.g., outside specified power supply range) and therefore, outside the warranted range.

-0.050

-0.045

-0.040

-0.035

-0.030

-0.025

-0.020

IOH(A)

VOH (V)

-0.050

-0.045

-0.040

-0.035

-0.030

-0.025

-0.020

-0.015

-0.010

-0.005

0.000

0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00

IOH(A)

VOH (V)

3.3V

3.6V

Absolute Maximum

-0.080

-0.070

-0.060

-0.050

-0.040

0 030

IOH(A)

VOH(V)

-0.080

-0.070

-0.060

-0.050

-0.040

-0.030

-0.020

-0.010

0.000

0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00

IOH(A)

VOH(V)

3.3V

3.6V

Absolute Maximum

0.015

0.020

0.025

0.030

0.035

0.040

0.045

0.050

IOH(A)

VOL(V)

0.000

0.005

0.010

0.015

0.020

0.025

0.030

0.035

0.040

0.045

0.050

0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00

IOH(A)

VOL(V)

3.3V

3.6V

Absolute Maximum

0020

0.030

0.040

0.050

0.060

0.070

0.080

IOH(A)

VOL(V) 8X

0.000

0.010

0.020

0.030

0.040

0.050

0.060

0.070

0.080

0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00

IOH(A)

VOL(V) 8X

3.3V

3.6V

Absolute Maximum

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 574  2009-2012 Microchip Technology Inc.

FIGURE 33-5: TYPICAL IPD CURRENT @ VDD = 3.3V

FIGURE 33-6: TYPICAL IDD CURRENT – VDD = 3.3V @ +85ºC

FIGURE 33-7: TYPICAL IDOZE CURRENT @ VDD = 3.3V

FIGURE 33-8: TYPICAL IIDLE CURRENT – VDD = 3.3V @ +85ºC

400

600

800

1,000

1,200

1,400

1,600

1,800

IPD (µA)

200

400

600

800

1,000

1,200

1,400

1,600

1,800

-40-30-20-10 0 102030405060708090100110120

IPD (µA)

Temperature (Celsius)

30.00

40.00

50.00

60.00

70.00

80.00

DCurrent (mA)

0.00

10.00

20.00

0 10203040506070

MIPS

1:1 1:2 1:64 1:128

IDOZE (mA)

Doze Ratio

15 00

20.00

25.00

30.00

35.00

40.00

45.00

ECurrent (mA)

0.00

5.00

10.00

0 10203040506070

IID

MIPS

 2009-2012 Microchip Technology Inc. DS70616G-page 575

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

FIGURE 33-9: TYPICAL FRC FREQUENCY @ VDD = 3.3V FIGURE 33-10: TYPICAL LPRC FREQUENCY @ VDD = 3.3V

7320

7340

7360

7380

7400

FRC Frequency (kHz)

7280

7300

7320

7340

7360

7380

7400

-40-30-20-100 102030405060708090100110120

FRC Frequency (kHz)

Temperature (Celsius)

32.2

32.4

32.6

32.8

33.0

33.2

LPRC Frequency (kHz)

31.8

32.0

32.2

32.4

32.6

32.8

33.0

33.2

-40-30-20-100 102030405060708090100110120

LPRC Frequency (kHz)

Temperature (Celsius)

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 576  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 577

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

34.0 PACKAGING INFORMATION

34.1 Package Marking Information

64-Lead TQFP (10x10x1 mm)

XXXXXXXXXX

YYWWNNN

Example

dsPIC33EP

256MU806

0510017

Legend: XX...X Customer-specific information

Y Year code (last digit of calendar year)

YY Year code (last 2 digits of calendar year)

WW Week code (week of January 1 is week ‘01’)

NNN Alphanumeric traceability code

Pb-free JEDEC designator for Matte Tin (Sn)

*This package is Pb-free. The Pb-free JEDEC designator ( )

can be found on the outer packaging for this package.

Note: In the event the full Microchip part number cannot be marked on one line, it will

be carried over to the next line, thus limiting the number of available

characters for customer-specific information.

-I/PT

64-Lead QFN (9x9x0.9 mm) Example

XXXXXXXXXX

YYWWNNN

33EP256MU

806-I/MR

0610017

100-Lead TQFP (12x12x1 mm)

XXXXXXXXXXXX

YYWWNNN

Example

dsPIC33EP256

MU810-I/PT

0510017

100-Lead TQFP (14x14x1 mm)

XXXXXXXXXXXX

YYWWNNN

Example

dsPIC33EP256

MU810-I/PF

0510017

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 578  2009-2012 Microchip Technology Inc.

34.1 Package Marking Information (Continued)

144-Lead TQFP (16x16x1 mm)

XXXXXXXXXXXX

YYWWNNN

Example

dsPIC33EP256

MU814-I/PH

0510017

121-Lead TFBGA (10x10x1.2 mm) Example

144-Lead LQFP (20x20x1.4 mm)

XXXXXXXXXXXX

YYWWNNN

Example

dsPIC33EP256

MU814-I/PL

0510017

XXXXXXXXXX

YYWWNNN

33EP256MU

810-I/BG

0610017

 2009-2012 Microchip Technology Inc. DS70616G-page 579

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

34.2 Package Details

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 580  2009-2012 Microchip Technology Inc.

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

 2009-2012 Microchip Technology Inc. DS70616G-page 581

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 582  2009-2012 Microchip Technology Inc.

64-Lead Plastic Thin Quad Flatpack (PT) – 10x10x1 mm Body, 2.00 mm Footprint [TQFP]

Notes:

1. Pin 1 visual index feature may vary, but must be located within the hatched area.

2. Chamfers at corners are optional; size may vary.

3. Dimensions D1 and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.25 mm per side.

4. Dimensioning and tolerancing per ASME Y14.5M.

BSC: Basic Dimension. Theoretically exact value shown without tolerances.

REF: Reference Dimension, usually without tolerance, for information purposes only.

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

Units MILLIMETERS

Dimension Limits MIN NOM MAX

Number of Leads N 64

Lead Pitch e 0.50 BSC

Overall Height A – – 1.20

Molded Package Thickness A2 0.95 1.00 1.05

Standoff A1 0.05 – 0.15

Foot Length L 0.45 0.60 0.75

Footprint L1 1.00 REF

Foot Angle φ0° 3.5° 7°

Overall Width E 12.00 BSC

Overall Length D 12.00 BSC

Molded Package Width E1 10.00 BSC

Molded Package Length D1 10.00 BSC

Lead Thickness c 0.09 – 0.20

Lead Width b 0.17 0.22 0.27

Mold Draft Angle Top α11° 12° 13°

Mold Draft Angle Bottom β11° 12° 13°

NOTE 1123 NOTE 2

Microchip Technology Drawing C04-085B

 2009-2012 Microchip Technology Inc. DS70616G-page 583

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 584  2009-2012 Microchip Technology Inc.

100-Lead Plastic Thin Quad Flatpack (PT) – 12x12x1 mm Body, 2.00 mm Footprint [TQFP]

Notes:

1. Pin 1 visual index feature may vary, but must be located within the hatched area.

2. Chamfers at corners are optional; size may vary.

3. Dimensions D1 and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.25 mm per side.

4. Dimensioning and tolerancing per ASME Y14.5M.

BSC: Basic Dimension. Theoretically exact value shown without tolerances.

REF: Reference Dimension, usually without tolerance, for information purposes only.

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

Units MILLIMETERS

Dimension Limits MIN NOM MAX

Number of Leads N 100

Lead Pitch e 0.40 BSC

Overall Height A – – 1.20

Molded Package Thickness A2 0.95 1.00 1.05

Standoff A1 0.05 – 0.15

Foot Length L 0.45 0.60 0.75

Footprint L1 1.00 REF

Foot Angle φ0° 3.5° 7°

Overall Width E 14.00 BSC

Overall Length D 14.00 BSC

Molded Package Width E1 12.00 BSC

Molded Package Length D1 12.00 BSC

Lead Thickness c 0.09 – 0.20

Lead Width b 0.13 0.18 0.23

Mold Draft Angle Top α11° 12° 13°

Mold Draft Angle Bottom β11° 12° 13°

123

NOTE 1NOTE 2

A1 L1

Microchip Technology Drawing C04-100B

 2009-2012 Microchip Technology Inc. DS70616G-page 585

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 586  2009-2012 Microchip Technology Inc.

100-Lead Plastic Thin Quad Flatpack (PF) – 14x14x1 mm Body, 2.00 mm Footprint [TQFP]

Notes:

1. Pin 1 visual index feature may vary, but must be located within the hatched area.

2. Chamfers at corners are optional; size may vary.

3. Dimensions D1 and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.25 mm per side.

4. Dimensioning and tolerancing per ASME Y14.5M.

BSC: Basic Dimension. Theoretically exact value shown without tolerances.

REF: Reference Dimension, usually without tolerance, for information purposes only.

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

Units MILLIMETERS

Dimension Limits MIN NOM MAX

Number of Leads N 100

Lead Pitch e 0.50 BSC

Overall Height A – – 1.20

Molded Package Thickness A2 0.95 1.00 1.05

Standoff A1 0.05 – 0.15

Foot Length L 0.45 0.60 0.75

Footprint L1 1.00 REF

Foot Angle φ0° 3.5° 7°

Overall Width E 16.00 BSC

Overall Length D 16.00 BSC

Molded Package Width E1 14.00 BSC

Molded Package Length D1 14.00 BSC

Lead Thickness c 0.09 – 0.20

Lead Width b 0.17 0.22 0.27

Mold Draft Angle Top α11° 12° 13°

Mold Draft Angle Bottom β11° 12° 13°

NOTE 1NOTE 2

123

LA1 L1

Microchip Technology Drawing C04-110B

 2009-2012 Microchip Technology Inc. DS70616G-page 587

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 588  2009-2012 Microchip Technology Inc.

 2009-2012 Microchip Technology Inc. DS70616G-page 589

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 590  2009-2012 Microchip Technology Inc.

 2009-2012 Microchip Technology Inc. DS70616G-page 591

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

144-Lead Plastic Low Profile Quad Flatpack (PL)  20x20x1.40 mm Body, with 2.00 mm

Footprint [LQFP]

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 592  2009-2012 Microchip Technology Inc.

144-Lead Plastic Low Profile Quad Flatpack (PL)  20x20x1.40 mm Body, with 2.00 mm

Footprint [LQFP]

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

 2009-2012 Microchip Technology Inc. DS70616G-page 593

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 594  2009-2012 Microchip Technology Inc.

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

 2009-2012 Microchip Technology Inc. DS70616G-page 595

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 596  2009-2012 Microchip Technology Inc.

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

 2009-2012 Microchip Technology Inc. DS70616G-page 597

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

APPENDIX A: REVISION HISTORY

Revision A (December 2009)

This is the initial released version of this document.

Revision B (July 2010)

This revision includes minor typographical and

formatting changes throughout the data sheet text.

The major changes are referenced by their respective

section in Table A-1.

TABLE A-1: MAJOR SECTION UPDATES

Section Name Update Description

“High-Performance, 16-bit Digital

Signal Controllers and

Microcontrollers”

Removed reference to dual triggers for Motor Control Peripherals.

Relocated the VBUSST pin in all pin diagrams (see “Pin Diagrams”, Table 2

and Table 3).

Added SCK2, SDI2, SDO2 pins in pin location 4,5 and 6 respectively in 64-pin

QFN.

Added SCK2, SDI2, SDO2 pins in pin location 4,5 and 6 respectively in 64-pin

TQFP.

Added SCK2, SDI2, SDO2 pins in pin location 10,11 and 12 respectively in

100-pin TQFP.

Added SCK2, SDI2, SDO2 pins in Table 2 and Table 3.

Moved the RP30 pin to pin location 95, and the RP31 pin to pin location 96 in

the 144-pin TQFP and 144-pin LQFP pin diagrams.

Section 1.0 “Device Overview” Removed the SCL1 and SDA1 pins from the Pinout I/O Descriptions (see

Table 1-1).

Section 2.0 “Guidelines for

Getting Started with 16-bit Digital

Signal Controllers and

Microcontrollers”

Removed Section 2.8 “Configuration of Analog and Digital Pins During ICSP

Operations”

Section 3.0 “CPU” Added Note 4 to the CPU Status Register (SR) in Register 3-1.

Added the VAR bit (CORCON<15>) to Register 3-2.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 598  2009-2012 Microchip Technology Inc.

Section 4.0 “Memory

Organization”

Added the Write Latch and Auxiliary Interrupt Vector to the Program Memory

Map (see Figure 4-1).

Updated the All Resets value for the DSRPAG and DSWPAG registers in the

CPU Core Register Maps (see Table 4-1 and Table 4-2).

Updated the All Resets value for the INTCON2 register in the Interrupt

Controller Register Maps (see Table 4-3 through Table 4-6).

Updated the All Resets values for all registers in the Output Compare 1 -

Output Compare 16 Register Map, with the exception of the OCxTMR and

OCxCON1 registers (see Table 4-9).

Removed the DTM bit (TRGCON1<7> from all PWM Generator # Register

Maps (see Table 4-11 through Table 4-17).

Updated the All Resets value for the QEI1IOC register in the QEI1 Register

Map (see Table 4-18).

Updated the All Resets value for the QEI2IOC register in the QEI1 Register

Map (see Table 4-19).

Added Note 4 to the USB OTG Register Map (see Table 4-25)

Updated all addresses in the Real-Time Clock and Calendar Register Map (see

Table 4-34).

Removed RPINR22 from Table 4-37 through Table 4-40.

Updated the All Resets values for all registers in the Peripheral Pin Select Input

through Table 4-40).

Added the VREGSF bit (RCON<11>) to the System Control Register Map (see

Table 4-43).

Added the REFOMD bit (PMD4<3>) to the PMD Register Maps (see Table 4-44

through Table 4-47).

Changed the bit range for CNT from <15:0> to <13:0> for all DMAxCNT

registers in the DMAC Register Map (see Table 4-49).

Updated the All Resets value and removed the ANSC15 and ANSC12 bits in

the ANSLEC registers in the PORTC Register Maps (see Table 4-52 and

Table 4-53).

Updated DSxPAG and Page Description of O, Read and U, Read in Table 4-66.

Added Note to the Table 4-67.

Updated Arbiter Architecture in Figure 4-8.

Updated the Unimplemented value and removed the LATG3 and LATG2 bits in

the LATG registers and the CNPUG3 and CNPUG2 bits from the CNPUG

registers in the PORTG Register Maps (see Table 4-60 and Table 4-61)

Updated the All Resets value and removed the TRISG3 and TRISG2 bits in the

TRISG registers and the ODCG3 and ODCG2 bits from the ODCG registers in

the PORTG Register Maps (see Table 4-60 and Table 4-61).

Section 5.0 “Flash Program

Memory”

Updated the NVMOP<3:0> = 1110 definition to Reserved and added Note 6 to

the Nonvolatile Memory (NVM) Control Register (see Register 5-1).

Section 6.0 “Resets” Added the VREGSF bit (RCON<11>) to the Reset Control Register (see

TABLE A-1: MAJOR SECTION UPDATES (CONTINUED)

Section Name Update Description

 2009-2012 Microchip Technology Inc. DS70616G-page 599

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Section 7.0 “Interrupt Controller” Added the VAR bit (CORCON<15>) to the Core Control Register (see

Changed the default POR value for the GIE bit (INTCON2<15) to R/W-1 (see

Changed the VECNUM<7:0> = 11111111 pending interrupt vector number to

263 in the Interrupt Control and Status Register (see Register 7-7).

Section 8.0 “Direct Memory

Access (DMA)”

Updated Section 8.1 “DMAC Registers”.

Updated DMA Controller in Figure 8-1.

Added Note 1 to the DMA Channel x Peripheral Address Register (see

Added Note 1 and Note 2 to the DMA Channel x Transfer Count Register (see

Updated all RQCOLx bit definitions, changing Peripheral Write to Transfer

Request in the DMA Request Collision Status Register (see Register 8-12).

Section 9.0 “Oscillator

Configuration”

Added the Reference Oscillator Control Register (see Register 9-7).

Added Note 3 and 4 to the CLKDIV Register (see Register 9-2)

Section 10.0 “Power-Saving

Features”

Added the DCIMD and C2MD bits to the Peripheral Module Disable Control

Added the IC6MD, IC5MD, IC4MD, IC3MD, OC8MD, OC7MD, OC6MD, and

OC5MD bits to the Peripheral Module Disable Control Register 2 (see

Added the T9MD, T8MD, T7MD, and T6MD bits and removed the DSC1MD bit

in the Peripheral Module Disable Control Register 3 (see Register 10-3).

Added the REFOMD bit (PMD4<3>) to the Peripheral Module Disable Control

Section 11.0 “I/O Ports” Updated the first paragraph of Section 11.2 “Configuring Analog and Digital

Port Pins”.

Updated the PWM Fault, Dead-Time Compensation, and Synch Input register

numbers of the Selectable Input Sources (see Table 11-2).

Removed RPINR22 register.

Bit names and definitions were modified in the following registers:

• Peripheral Pin Select Input Register 37 (see Register 11-37)

• Peripheral Pin Select Input Register 38 (see Register 11-38)

• Peripheral Pin Select Input Register 39 (see Register 11-39)

• Peripheral Pin Select Input Register 40 (see Register 11-40)

• Peripheral Pin Select Input Register 41 (see Register 11-41)

• Peripheral Pin Select Input Register 42 (see Register 11-42)

• Peripheral Pin Select Input Register 43 (see Register 11-43)

Section 12.0 “Timer1” Added Note in Register 12-1.

Section 14.0 “Input Capture” Added Note 1 to the Input Capture Block Diagram (see Figure 14-1).

Section 15.0 “Output Compare” Added Note 1 to the Output Compare Module Block Diagram (see Figure 15-1).

Added Note 2 to the Output Compare x Control Register 2 (see Register 15-2).

Section 16.0 “High-Speed PWM

Module (dsPIC33EPXXXMU806/

810/814 Devices Only)”

Added Comparator bit values for the CLSRC<4:0> and FLTSRC<4:0> bits in

the PWM Fault Current-Limit Control Register (see Register 16-21).

TABLE A-1: MAJOR SECTION UPDATES (CONTINUED)

Section Name Update Description

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 600  2009-2012 Microchip Technology Inc.

Section 17.0 “Quadrature

Encoder Interface (QEI) Module

(dsPIC33EPXXXMU806/810/814

Devices Only)”

Reordered the bit values for the OUTFNC<1:0> bits and updated the default

POR bit value to ‘x’ for the HOME, INDEX, QEB, and QEA bits in the QEI I/O

Control Register (see Register 17-2).

Section 23.0 “10-bit/12-bit

Analog-to-Digital Converter

(ADC)”

Updated VREFL in the ADC1 and ADC2 Module Block Diagram (see

Figure 23-1).

Section 25.0 “Comparator

Module”

Added Note 1 to the Comparator I/O Operating Modes (see Figure 25-1).

Removed the CLPWR bit (CMxCON<12>) (see Register 25-2).

Section 29.0 “Special Features” Added a new first paragraph to Section 29.1 “Configuration Bits”

Section 30.0 “Instruction Set

Summary”

The following instructions have been updated (see Table 30-2):

•BRA

•CALL

• CPBEQ

• CPBGT

• CPBLT

• CPBNE

•GOTO

• MOVPAG

•MUL

• RCALL

• RETFIE

• RETLW

• RETURN

• TBLRDH

• TBLRDL

Section 32.0 “Electrical

Characteristics”

Updated the Typical and Maximum values for DC Characteristics: Operating

Current (IDD) (see Table 32-5).

Updated the Typical and Maximum values for DC Characteristics: Idle Current

(IIDLE) (see Table 32-6).

Updated the Maximum values for DC Characteristics: Power-down Current

(IPD) (see Table 32-7).

Updated the Maximum values for DC Characteristics: Doze Current (IDOZE)

(see Table 32-8).

Updated the parameter numbers for Internal FRC Accuracy (see Table 32-19).

Updated the parameter numbers and the Typical value for parameter F21b for

Internal RC Accuracy (see Table 32-20).

Updated the Minimum value for PM6 and the Typical and Maximum values for

PM7 in Parallel Master Port Read Requirements (see Table 32-52).

Added DMA Module Timing Requirements (see Table 32-54).

TABLE A-1: MAJOR SECTION UPDATES (CONTINUED)

Section Name Update Description

 2009-2012 Microchip Technology Inc. DS70616G-page 601

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Revision C (May 2011)

This revision includes minor typographical and

formatting changes throughout the data sheet text.

These global changes were implemented:

• All instances of VDDCORE have been removed.

• References to remappable pins have been

updated to clarify output-only pins (RPn) versus

input/output pins (RPIn).

• The minimum VDD value was changed from 2.7V to

3.0V to adhere to the current BOR specification.

The major changes are referenced by their respective

section in Table A-2.

TABLE A-2: MAJOR SECTION UPDATES

Section Name Update Description

High-Performance, 16-bit Digital

Signal Controllers and

Microcontrollers

Removed the shading for D+/RG2 and D-/RG3 pin designations in all pin

diagrams, as these pins are not 5V tolerant.

References to remappable pins have been updated to clarify input/output pins

(RPn) and input-only pins (RPIn).

Section 2.0 “Guidelines for

Getting Started with 16-bit Digital

Signal Controllers and

Microcontrollers”

Add information on the VUSB pin in Section 2.1 “Basic Connection

Requirements”.

Updated the title of Section 2.3 to Section 2.3 “CPU Logic Filter Capacitor

Connection (VCAP)” and modified the first paragraph.

Section 3.0 “CPU” Added Note 2 to the Programmer’s Model Register Descriptions

(see Table 3-1).

Section 4.0 “Memory

Organization”

Added the CANCKS bit (CxCTRL1<11>) to the ECAN1 and ECAN 2 Register

Maps (see Table 4-26 and Table 4-29).

Added the SBOREN bit (RCON<13>) to the System Control Register Map (see

Table 4-43).

Added Note 1 to the PORTG Register maps (see Table 4-60 and Table 4-61).

Updated the Page Description for DSRPAG = 0x1FF and DSRPAG = 0x200 in

Table 4-66.

Updated the second paragraph of Section 4.2.9 “EDS Arbitration and Bus

Master Priority”.

Updated the last note box in Section 4.2.10 “Software Stack”.

Section 5.0 “Flash Program

Memory”

Updated the equation formatting in Section 5.3 “Programming Operations”.

Added the Non-Volatile Memory Upper Address (NVMADRU) and Non-Volatile

Memory Address (NVMADR) registers (see Register 5-2 and Register 5-3).

Section 6.0 “Resets” Added Security Reset to the Reset System Block Diagram (see Figure 6-1).

Added the SBOREN bit (RCON<13>) and Notes 3 and 4 to the Reset Control

Section 11.0 “I/O Ports” References to remappable pins have been updated to clarify input/output pins

(RPn) and input-only pins (RPIn).

Added the new column, Input/Output, to Input Pin Selection for Selectable Input

Sources (see Table 11-2).

Section 17.0 “Quadrature

Encoder Interface (QEI) Module

(dsPIC33EPXXXMU806/810/814

Devices Only)”

Updated the definition for the INTHLD<31:0> bits (see Register 17-19 and

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 602  2009-2012 Microchip Technology Inc.

Section 21.0 “Enhanced CAN

(ECAN™) Module”

Added the CANCKS bit to the ECAN Control Register 1 (CiCTRL1)

(see Register 21-1).

Section 22.0 “USB On-The-Go

(OTG) Module”

Removed the USB 3.3V Regulator logic from the USB Interface Diagram

(see Figure 22-1).

Section 23.0 “10-bit/12-bit

Analog-to-Digital Converter

(ADC)”

Updated the ADC Conversion Clock Period Block Diagram (see Figure 23-2).

Section 29.0 “Special Features” Updated the last paragraph of Section 29.1 “Configuration Bits”

Added a note box after the last paragraph of Section 29.3 “BOR: Brown-out

Reset (BOR)”.

Added the RTSP Effect column to the Configuration Bits Description

(see Table 29-2).

Section 30.0 “Instruction Set

Summary”

Updated all Status Flags Affected to None for the MOV instruction and added

Note 2 (see Table 30-2).

Section 32.0 “Electrical

Characteristics”

Updated the Absolute Maximum Ratings (see page 457).

Added Note 1 to the Operating MIPS vs. Voltage (see Table 32-1).

Added parameter DI31 (ICNPD) to the I/O Pin Input Specifications (see

Table 32-9).

Updated the Minimum value for parameter DO26 in the I/O Pin Output

Specifications (see Table 32-10).

Updated the Minimum value for parameter D132b and the Minimum and

Maximum values for parameters D136a, D136b, D137a, D137b, D138a, and

D138b in the Program Memory specification (see Table 32-12).

Updated the Minimum, Typical, and Maximum values for parameter OS10

(Oscillator Crystal Frequency: SOSC) in the External Clock Timing

Requirements (see Table 32-16).

Added Note 2 to the PLL Clock Timing Specifications (see Table 32-17).

Updated all Timer1 External Clock Timing Requirements (see Table 32-23).

Replaced Table 32-34 with Timer2, Timer4, Timer6, Timer8 External Clock

Timing Requirements and Timer3, Timer5, Timer7, Timer9 External Clock

Timing Requirements (see Table 32-24 and Table 32-25, respectively).

Updated the Maximum value for parameter OC15 and the Minimum value for

parameter OC20 in the OC/PWM Mode Timing Requirements

(see Table 32-29).

Updated the Operating Temperature in the ECAN Module I/O Timing

Requirements and USB OTG Timing Requirements (see Table 32-51 and

Table 32-53, respectively).

Updated all SPI specifications (see Figure 32-15 through Figure 32-30 and

Table 32-33 through Table 32-48).

Removed Note 4 from the DCI Module Timing Requirements

(see Table 32-59).

Updated the Standard Operating Conditions voltage for the Comparator

Specifications (see Table 32-61 through Table 32-64).

TABLE A-2: MAJOR SECTION UPDATES (CONTINUED)

Section Name Update Description

 2009-2012 Microchip Technology Inc. DS70616G-page 603

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Revision D (August 2011)

This revision includes minor typographical and

formatting changes throughout the data sheet text.

The Data Converter Interface (DCI) module is available

on all dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814 devices. References

throughout the document have been updated

accordingly.

The following pin name changes were implemented

throughout the document:

• C1INA renamed to C1IN1+

• C1INB renamed to C1IN2-

• C1INC renamed to C1IN1-

• C1IND renamed to C1IN3-

• C2INA renamed to C2IN1+

• C2INB renamed to C2IN2-

• C2INC renamed to C2IN1-

• C2IND renamed to C2IN3-

• C3INA renamed to C3IN1+

• C3INB renamed to C3IN2-

• C3INC renamed to C3IN1-

• C3IND renamed to C3IN3-

The other major changes are referenced by their

respective section in Table A-3.

TABLE A-3: MAJOR SECTION UPDATES

Section Name Update Description

Section 1.0 “Device Overview” Added Section 1.1 “Referenced Sources”.

Section 2.0 “Guidelines for Getting

Started with 16-bit Digital Signal

Controllers and Microcontrollers”

Updated the Note in Section 2.1 “Basic Connection Requirements”.

Section 3.0 “CPU” Updated Section 3.1 “Registers”.

Section 4.0 “Memory Organization” Updated FIGURE 4-3: “Data Memory Map for dsPIC33EP512MU810/814

Devices with 52 KB RAM” and FIGURE 4-5: “Data Memory Map for

dsPIC33EP256MU806/810/814 Devices with 28 KB RAM”.

Updated the IFS3, IEC3, IPC14, and IPC15 SFRs in the Interrupt Controller

Updated the SMPI bits for the AD1CON2 and AD2CON2 SFRs in the ADC1

and ADC2 Register Map (see Table 4-23).

Updated the All Resets values for the CLKDIV and PLLFBD SFRs and

removed the SBOREN bit in the System Control Register Map

(see Table 4-43).

Section 6.0 “Resets” Removed the SBOREN bit and Notes 3 and 4 from the Reset Control

Section 8.0 “Direct Memory Access

(DMA)”

Removed Note 2 from the DMA Channel x IRQ Select Register (see

Section 9.0 “Oscillator

Configuration”

Updated the PLL Block Diagram (see Figure 9-2).

Updated the value at PORT and the default designations for the

DOZE<2:0>, FRCDIV<2:0>, and PLLPOST<1:0> bits in the Clock Divisor

and Register 9-3).

Section 23.0 “10-bit/12-bit Analog-

to-Digital Converter (ADC)”

Added Note 4 and updated the ADC Buffer names in the ADCx Module

Block Diagram (see Figure 23-1).

Added Note 3 to the ADCx Control Register 1 (see Register 23-1).

Added the new ADC2 Control Register 2 (see Register 23-3).

Updated the SMPI<4:0> bit value definitions in the ADC1 Control Register 2

(see Register 23-2).

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 604  2009-2012 Microchip Technology Inc.

Section 25.0 “Comparator Module” Updated the Comparator I/O Operating Modes diagram (see Figure 25-1).

Added Note 2 to the Comparator Voltage Reference Control Register (see

Section 29.0 “Special Features” Added Note 3 to the Connections for the On-chip Voltage Regulator (see

Figure 29-1).

Section 32.0 “Electrical

Characteristics”

Removed the Voltage on VCAP with respect to VSS from the Absolute

Maximum Ratings(1).

Removed Note 3 and parameter DC18 from the DC Temperature and

Voltage Specifications (see Table 32-4).

Updated the notes in the DC Characteristics: Operating Current (IDD)

(see Table 32-5).

Updated the notes in the DC Characteristics: Idle Current (IIDLE)

(see Table 32-6).

Updated the Typical and Maximum values for parameter DC60c and the

notes in the DC Characteristics: Power-down Current (IPD) (see Table 32-7).

Updated the notes in the DC Characteristics: Doze Current (IDOZE)

(see Table 32-8).

Updated the conditions for parameters DI60a and DI60b (see Table 32-9).

Updated the conditions for parameter BO10 in the BOR Electrical

Characteristics (see Table 32-10).

Added Note 1 to the Internal Voltage Regulator Specifications

(see Table 32-13).

Updated the Minimum and Maximum values for parameter OS53 in the PLL

Clock Timing Specifications (see Table 32-17).

Updated the Minimum and Maximum values for parameter F21b in the

Internal LPRC Accuracy specifications (see Table 32-20).

Added Note 2 to the ADC Module Specifications (see Table 32-54).

TABLE A-3: MAJOR SECTION UPDATES (CONTINUED)

Section Name Update Description

 2009-2012 Microchip Technology Inc. DS70616G-page 605

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Revision E (August 2011)

This revision includes the following updates to

Section 32.0 “Electrical Characteristics”:

• The maximum HS value for parameter OS10 was

updated (see Table 32-16)

• The OC/PWM Module Timing Characteristics for

OCx were updated (see Figure 32-10)

• The Maximum Data Rate values were updated for

the SPI1, SPI3, and SPI4 Maximum Data/Clock

Rate Summary (see Table 32-33)

• These SPI1, SPI3, and SPI4 Timing Requirements

were updated:

- Maximum value for parameter SP10 and the

minimum clock period value for SCKx in Note 3

(see Table 32-34, Table 32-35, and Table 32-36)

- Maximum value for parameter SP70 and the

minimum clock period value for SCKx in Note 3

(see Table 32-38 and Table 32-40)

• The Maximum Data Rate values were updated for

the SPI2 Maximum Data/Clock Rate Summary

(see Table 32-41)

• These SPI2 Timing Requirements were updated:

- Maximum value for parameter SP10 and the

minimum clock period value for SCKx in Note 3

(see Table 32-42, Table 32-43, and Table 32-44)

- Maximum value for parameter SP70 and the

minimum clock period value for SCKx in Note 3

(see Table 32-45 through Table 32-48)

- Minimum value for parameters SP40 and SP41

see Table 32-43 through Table 32-48)

• These ADC Module Specifications were updated

(see Table 32-54):

- Minimum value for parameter AD05

- Maximum value for parameter AD06

- Minimum value for parameter AD07

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 606  2009-2012 Microchip Technology Inc.

Revision F (February 2012)

This revision includes typographical and formatting

changes throughout the data sheet text.

Throughout the document, references to the package

formerly known as XBGA where changed to TFBGA.

In addition, where applicable, new sections were added

to each peripheral chapter that provide information and

links to related resources, as well as helpful tips. For

examples, see Section 18.1 “SPI Helpful Tips” and

Section 18.2 “SPI Resources”. The major changes

are referenced by their respective section in Table A-4.

TABLE A-4: MAJOR SECTION UPDATES

Section Name Update Description

“16-Bit Microcontrollers and

Digital Signal Controllers with

High-Speed PWM, USB and

Advanced Analog”

The content on the first page of this section was extensively reworked to

provide the reader with the key features and functionality of this device family in

an “at-a-glance” format.

The following devices were added to the Controller Families table (see Table 1

and the “Pin Diagrams” section):

• dsPIC33EP512MC806

• dsPIC33EP512GP806

• PIC24EP512GP806

Section 2.0 “Guidelines for

Getting Started with 16-Bit Digital

Signal Controllers and

Microcontrollers”

Added Section 2.9 “Application Examples”

Section 3.0 “CPU” Updated the Status Register information in the Programmer’s Model (see

Figure 3-2).

Section 4.0 “Memory

Organization”

Added Interrupt Controller Register Maps (see Table 4-6 and Ta b le 4- 7 ).

Added Peripheral Pin Select Output Register Map (see Ta b le 4- 3 9 ).

Added PMD Register Maps (see Table 4-50 and Ta b l e 4 - 5 1 ).

Added PORTF Register Map (see Ta b l e 4- 6 4 ).

Added PORTG Register Map (see Ta b l e 4- 6 7 ).

Updated the second note in Section 4.7 “Bit-Reversed Addressing

(dsPIC33EPXXXMU806/810/814 Devices Only)”.

Section 11.0 “I/O Ports” Added RPOR10: Peripheral Pin Select Output Register 10

(see Register 11-54).

Section 14.0 “Input Capture” Updated the Input Capture Module Block Diagram (see Figure 14-1).

Section 15.0 “Output Compare” Updated the Output Compare Module Block Diagram (see Figure 15-1).

Section 25.0 “Comparator

Module”

Updated the User-programmable Blanking Function Block Diagram (see

Figure 25-3).

Updated the bit definitions in the Comparator Mask Gating Control Register

(see Register 25-4).

Section 29.0 “Special Features” Added Note 3 to the Configuration Bits Description (see Ta b le 29 - 2 ).

Section 32.0 “Electrical

Characteristics”

Updated the I/O pin Absolute Maximum Ratings.

Updated Note 1 in the DC Characteristics: Operating Current (see Table 32-5).

Updated Note 1 in the DC Characteristics: Idle Current (see Ta b le 32 - 6 ).

Updated Note 1 in the DC Characteristics: Power-down Current

(see Table 32-7).

Updated Note 1 in the DC Characteristics: Doze Current (see Table 32-8).

Removed parameters DO16 and DO26, added parameter DO26a, updated

parameters DO10 and DO20, and added Note 1 in the DC Characteristics: I/O

Pin Output Specifications (see Table 32-10).

 2009-2012 Microchip Technology Inc. DS70616G-page 607

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Revision G (October 2012)

This revision includes updates to the packaging

diagrams in Section 34.0 “Packaging Information”.

Preliminary has been removed and there are minor text

edits throughout the document.

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 608  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 609

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

INDEX

AC Characteristics ............................................................ 511

Capacitive Loading Requirements on

Output Pins ....................................................... 511

Comparator ............................................................... 567

Comparator Reference Voltage Settling Time .......... 568

I/O Timing Requirements .......................................... 515

Internal FRC Accuracy.............................................. 514

Internal LPRC Accuracy............................................ 514

Load Conditions ........................................................ 511

Temperature and Voltage Specifications .................. 511

ADC

Control Registers ...................................................... 417

Helpful Tips ............................................................... 416

Key Features............................................................. 413

Resources................................................................. 416

Analog-to-Digital Converter (ADC).................................... 413

Arithmetic Logic Unit (ALU)................................................. 46

Assembler

MPASM Assembler................................................... 496

Bit-Reversed Addressing .................................................. 131

Example .................................................................... 132

Implementation ......................................................... 131

Sequence Table (16-Entry)....................................... 132

Block Diagrams

16-Bit Timer1 Module................................................ 271

ADCx Conversion Clock Period ................................ 415

ADCx Module............................................................ 414

APLL Module ............................................................ 180

Comparator I/O Operating Modes............................. 437

Comparator Voltage Reference ................................ 438

Connections for On-Chip Voltage Regulator............. 481

CPU Core.................................................................... 38

CRC Shift Engine...................................................... 461

DCI Module ............................................................... 429

Digital Filter Interconnect .......................................... 439

DMA Controller ......................................................... 159

DMA Controller to Peripheral Associations............... 161

dsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814........................... 24

ECAN Module ........................................................... 360

EDS Arbiter Architecture........................................... 127

EDS Read Address Generation ................................ 122

EDS Write Address Generation ................................ 123

High-Speed PWM Architectural Overview ................ 294

High-Speed PWM Register Interconnection ............. 295

I2C Module................................................................ 346

Input Capture Module ............................................... 281

Multiplexing of Remappable Output for RPn............. 215

Oscillator System ...................................................... 178

Output Compare Module........................................... 287

PLL Module............................................................... 179

PMP Module Pinout, Connections to

External Devices............................................... 467

Programmable CRC Module..................................... 461

Quadrature Encoder Interface Module...................... 322

Reset System............................................................ 141

RTCC Module ........................................................... 450

Shared Port Structure ............................................... 208

SPIx module.............................................................. 337

Type B Timerx (Timer2, Timer4, Timer6, Timer8) .... 276

Type B, Type C Timer Pair (32-Bit Timer) ................ 277

Type C Timerx (Timer3, Timer5, Timer7, Timer9).... 276

U1RX Remappable Input.......................................... 210

UARTx Module ......................................................... 353

USB Interface ........................................................... 386

User-Programmable Blanking Function.................... 438

Watchdog Timer (WDT)............................................ 482

Brown-out Reset (BOR).................................................... 481

C Compilers

MPLAB C18.............................................................. 496

Code Examples

Connecting IC1 to HOME1 Digital Filter Input

on Pin 3 ............................................................ 217

Port Write/Read ........................................................ 209

PWRSAV Instruction Syntax .................................... 191

Code Protection................................................................ 483

CodeGuard Security ......................................................... 483

Comparator

Control Registers...................................................... 440

Resources ................................................................ 439

Configuration Bits ............................................................. 477

Description................................................................ 478

Configuration Register Map .............................................. 477

CPU

Addressing Modes...................................................... 37

Control Registers........................................................ 42

Data Space Addressing.............................................. 37

Instruction Set............................................................. 37

Resources .................................................................. 41

CRC

Overview................................................................... 462

Registers .................................................................. 463

Resources ................................................................ 462

Customer Change Notification Service............................. 616

Customer Notification Service .......................................... 616

Customer Support............................................................. 616

Data Address Space........................................................... 49

Memory Map for dsPIC33EP256MU806/810/814

Devices with 28-Kbyte RAM.................................... 52

Memory Map for dsPIC33EP512(GP/MC/MU)806/810/814

Devices with 52-Kbyte RAM.................................... 50

Memory Map for PIC24EP256GU810/814 Devices

with 28-Kbyte RAM.................................................. 53

Memory Map for PIC24EP512(GP/GU)806/810/814

Devices with 52-Kbyte RAM................................. 51

Near Data Space ........................................................ 49

Organization and Alignment ....................................... 49

SFR ............................................................................ 49

Width .......................................................................... 49

Data Converter Interface (DCI) Module ............................ 429

Data Memory

Paged Space ............................................................ 124

Data Space

Extended X ............................................................... 126

DC and AC Characteristics

Graphs and Tables ................................................... 573

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 610  2009-2012 Microchip Technology Inc.

DC Characteristics

Brown-out Reset (BOR) ............................................ 509

Comparator ............................................................... 567

Comparator Reference Voltage ................................ 568

Doze Current (IDOZE) ................................................ 505

I/O Pin Input Specifications....................................... 506

I/O Pin Output Specifications .................................... 509

Idle Current (IIDLE) .................................................... 503

Internal Voltage Regulator Specifications ................. 510

Operating Current (IDD)............................................. 502

Operating MIPS vs. Voltage...................................... 500

Power-Down Current (IPD) ........................................ 504

Program Memory ...................................................... 510

Temperature and Voltage Specifications .................. 501

Thermal Operating Conditions .................................. 500

DCI

Control Registers ...................................................... 431

Introduction ............................................................... 429

Resources................................................................. 430

Development Support ....................................................... 495

DMA Controller

Control Registers ...................................................... 162

Registers

DMA Channel IRQ Select ................................. 162

DMA Peripheral Address .................................. 162

DMA RAM Primary Start Address..................... 162

DMA RAM Secondary Start Address ................ 162

DMA Transfer Count ......................................... 162

DMAxCON ........................................................ 162

Resources................................................................. 162

Supported Peripherals .............................................. 159

DSP Engine......................................................................... 46

ECAN Module

Control Registers ...................................................... 362

Message Buffers ....................................................... 381

Modes of Operation .................................................. 361

Overview ................................................................... 359

Resources................................................................. 361

Electrical Characteristics................................................... 499

Absolute Maximum Ratings ...................................... 499

AC ............................................................................. 511

Enhanced CAN Module..................................................... 359

Equations

Device Operating Frequency .................................... 179

FAVCO Calculation ..................................................... 180

Maximum Row Write Time ........................................ 136

Minimum Row Write Time ......................................... 136

Programming Time ................................................... 136

Errata .................................................................................. 20

Flash Program Memory..................................................... 135

Control Registers ...................................................... 137

Operations ................................................................ 136

RTSP Operation........................................................ 136

Table Instructions...................................................... 135

High-Speed PWM ............................................................. 293

Resources................................................................. 296

I/O Ports............................................................................ 207

Configuring Analog Port Pins.................................... 209

Helpful Tips............................................................... 218

Input Change Notification ......................................... 209

Input Pin Selection.................................................... 213

Open-Drain Configuration......................................... 209

Output Selection for Remappable Pins (RPn) .......... 215

Parallel I/O (PIO) ...................................................... 207

Peripheral Pin Select (PPS)...................................... 210

Resources ................................................................ 219

Selectable Input Sources.......................................... 211

Write/Read Timing .................................................... 209

I2C

Control Registers...................................................... 348

Resources ................................................................ 347

In-Circuit Debugger........................................................... 483

In-Circuit Serial Programming (ICSP)............................... 483

Input Capture .................................................................... 281

Control Registers...................................................... 283

Resources ................................................................ 282

Instruction Addressing Modes .......................................... 128

File Register Instructions .......................................... 128

Fundamental Modes Supported ............................... 129

MAC Instructions ...................................................... 129

MCU Instructions ...................................................... 128

Move and Accumulator Instructions.......................... 129

Other Instructions ..................................................... 129

Instruction Set

Overview................................................................... 488

Summary .................................................................. 485

Inter-Integrated Circuit (I2C) ............................................. 345

Internal RC Oscillator

Use with WDT........................................................... 482

Internet Address ............................................................... 616

Interrupt Control and Status Registers ............................. 150

IECx.......................................................................... 150

IFSx .......................................................................... 150

INTCON1-INTCON4 ................................................. 150

INTTREG .................................................................. 150

IPCx.......................................................................... 150

Interrupt Controller

Auxiliary Interrupt Vector .......................................... 145

Interrupt Vector Table (IVT) ...................................... 145

Reset Sequence ....................................................... 145

Resources ................................................................ 150

JTAG Interface.................................................................. 483

Memory Maps

EDS .......................................................................... 126

Memory Organization ......................................................... 47

Message Buffers

ECAN Word 0 ........................................................... 381

ECAN Word 1 ........................................................... 381

ECAN Word 2 ........................................................... 382

ECAN Word 7 ........................................................... 384

Microchip Internet Web Site.............................................. 616

 2009-2012 Microchip Technology Inc. DS70616G-page 611

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Modulo Addressing ........................................................... 130

Applicability ............................................................... 131

Operation Example ................................................... 130

Start and End Address.............................................. 130

W Address Register Selection .................................. 130

MPLAB ASM30 Assembler, Linker, Librarian ................... 496

MPLAB Integrated Development Environment

Software.................................................................... 495

MPLAB PM3 Device Programmer .................................... 498

MPLAB REAL ICE In-Circuit Emulator System................. 497

MPLINK Object Linker/MPLIB Object Librarian ................ 496

Oscillator

Control Registers ...................................................... 182

Oscillator Configuration..................................................... 177

Bit Values for Clock Selection................................... 181

CPU Clocking System............................................... 179

Resources................................................................. 181

Output Compare ............................................................... 287

Resources................................................................. 288

Packaging ......................................................................... 577

Details ....................................................................... 582

Marking ............................................................. 577, 578

Parallel Master Port (PMP) ............................................... 467

Peripheral Module Disable (PMD) .................................... 192

Peripheral Pin Select

Control Registers ...................................................... 220

Peripherals Supported by DMA ........................................ 159

Pinout I/O Descriptions (table) ............................................ 25

PMP

Control Registers ...................................................... 469

Resources................................................................. 468

Power-Saving Features .................................................... 191

Clock Frequency, Clock Switching............................ 191

Doze Mode................................................................ 192

Instruction-Based Modes .......................................... 191

Idle .................................................................... 192

Sleep................................................................. 191

Interrupts Coincident with Power

Save Instructions .............................................. 192

Resources................................................................. 193

Special Function Registers ....................................... 193

Program Address Space..................................................... 47

Construction.............................................................. 133

Data Access from Address Generation..................... 133

Data Access from Program Memory Using

Table Instructions ............................................. 134

Memory Map ............................................................... 47

Table Read Instructions

TBLRDH ........................................................... 134

TBLRDL ............................................................ 134

Program Memory

Interrupt and Trap Vectors .......................................... 48

Organization................................................................ 48

Reset Vector ............................................................... 48

Resources................................................................... 54

Programmable Cyclic Redundancy Check (CRC)

Generator.................................................................. 461

Programmer’s Model........................................................... 39

PWM

Control Registers...................................................... 297

QEI

Control Registers...................................................... 324

Quadrature Encoder Interface (QEI)................................. 321

Resources ................................................................ 323

RCON

Control Register........................................................ 142

Reader Response............................................................. 617

Real-Time Clock and Calender (RTCC) ........................... 449

ADC1 and ADC2 ........................................................ 85

Comparator............................................................... 110

CPU Core (dsPIC33EPXXX(GP/MC/MU)806/810/814

Devices Only)........................................................... 55

CPU Core (PIC24EPXXX(GP/GU)810/814

Devices Only) ...................................................... 57

CRC............................................................................ 96

DCI ............................................................................. 87

DMAC ....................................................................... 111

ECAN1 (WIN (C1CTRL) = 0 or 1)............................... 90

ECAN1 (WIN (C1CTRL) = 0)...................................... 90

ECAN1 (WIN (C1CTRL) = 1)...................................... 91

ECAN2 (WIN (C2CTRL) = 0 or 1)............................... 93

ECAN2 (WIN (C2CTRL) = 0)...................................... 93

I2C1 and I2C2 ............................................................ 82

Input Capture 1 through Input Capture 16 .................. 71

Interrupt Controller (dsPIC33EPXXXGP806 and

PIC24EPXXXGP806 Devices Only) ....................... 66

Interrupt Controller (dsPIC33EPXXXMC806

Devices Only)........................................................... 64

Interrupt Controller (dsPIC33EPXXXMU806

Devices Only)........................................................... 62

Interrupt Controller (dsPIC33EPXXXMU810

Devices Only)........................................................... 60

Interrupt Controller (dsPIC33EPXXXMU814

Devices Only)........................................................... 58

Interrupt Controller (PIC24EPXXXGU810/814

Devices Only)........................................................... 68

NVM.......................................................................... 106

Output Compare 1 through Output Compare 16 ........ 73

Pad Configuration..................................................... 121

Parallel Master/Slave Port .......................................... 96

Peripheral Pin Select Input (dsPIC33EPXXX(MC/MU)806

Devices Only)......................................................... 103

Peripheral Pin Select Input (dsPIC33EPXXXMU810

Devices Only)......................................................... 101

Peripheral Pin Select Input (dsPIC33EPXXXMU814

Devices Only)........................................................... 99

Peripheral Pin Select Input (PIC24EPXXXGU810/814

Devices Only)......................................................... 105

Peripheral Pin Select Output (dsPIC33EPXXX(GP/MC/

MU)806 and PIC24EPXXXGP806

Devices Only)........................................................... 98

Peripheral Pin Select Output (dsPIC33EPXXXMU806

Devices Only)........................................................... 98

Peripheral Pin Select Output (dsPIC33EPXXXMU810/814

and PIC24EPXXXGU810/814 Devices Only) ........ 97

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 612  2009-2012 Microchip Technology Inc.

PMD (dsPIC33EPXXXGP8XX and

PIC24EPXXXGP8XX Devices Only)................. 109

PMD (dsPIC33EPXXXMC806 Devices Only) ........... 108

PMD (dsPIC33EPXXXMU806 Devices Only) ........... 108

PMD (dsPIC33EPXXXMU810 Devices Only) ........... 107

PMD (dsPIC33EPXXXMU814 Devices Only) ........... 107

PMD (PIC24EPXXXGU810/814 Devices Only) ........ 109

PORTA (dsPIC33EPXXXMU810/814 and

PIC24EPXXXGU810/814 Devices Only) .......... 115

PORTB...................................................................... 115

PORTC (dsPIC33EPXXX(GP/MC/MU)806 and

PIC24EPXXXGP806 Devices Only) ................. 116

PORTC (dsPIC33EPXXXMU810/814 and

PIC24EPXXXGU810/814 Devices Only) .......... 115

PORTD (dsPIC33EPXXX(GP/MC/MU)806 and

PIC24EPXXXGP806 Devices Only) ................. 116

PORTD (dsPIC33EPXXXMU810/814 and

PIC24EPXXXGU810/814 Devices Only) .......... 116

PORTE (dsPIC33EPXXX(GP/MC/MU)806 and

PIC24EPXXXGP806 Devices Only) ................. 117

PORTE (dsPIC33EPXXXMU810/814 and

PIC24EPXXXGU810/814 Devices Only) .......... 117

PORTF (dsPIC33EPXXX(GP/MC)806 and

PIC24EPXXXGP806 Devices Only) ................. 118

PORTF (dsPIC33EPXXXMU806 Devices Only)....... 118

PORTF (dsPIC33EPXXXMU810/814 and

PIC24EPXXXGU810/814 Devices Only) .......... 117

PORTG (dsPIC33EPXXX(GP/MC)806 and

PIC24EPXXXGP806 Devices Only) ................. 119

PORTG (dsPIC33EPXXXMU806 Devices Only) ...... 119

PORTG (dsPIC33EPXXXMU810/814 and

PIC24EPXXXGU810/814 Devices Only) .......... 118

PORTH (dsPIC33EPXXXMU814 and

PIC24EPXXXGU814 Devices Only) ................. 120

PORTJ (dsPIC33EPXXXMU814 and

PIC24EPXXXGU814 Devices Only) ................. 120

PORTK (dsPIC33EPXXXMU814 and

PIC24EPXXXGU814 Devices Only) ................. 121

PWM (dsPIC33EPXXX(MC/MU)806/810/814

Devices Only) ...........................................................76

PWM Generator 1 (dsPIC33EPXXX(MC/MU)806/810/814

Devices Only) ...........................................................76

PWM Generator 2 (dsPIC33EPXXX(MC/MU)806/810/814

Devices Only) ...........................................................77

PWM Generator 3 (dsPIC33EPXXX(MC/MU)806/810/814

Devices Only) ...........................................................77

PWM Generator 4 (dsPIC33EPXXX(MC/MU)806/810/814

Devices Only) ...........................................................78

PWM Generator 5 (dsPIC33EPXXX(MC/MU)810/814

Devices Only) ...........................................................78

PWM Generator 6 (dsPIC33EPXXX(MC/MU)810/814

Devices Only) ...........................................................79

PWM Generator 7 (dsPIC33EPXXX(MC/MU)814

Devices Only) ...........................................................79

QEI1 (dsPIC33EPXXX(MC/MU)806/810/814

Devices Only) ...........................................................80

QEI2 (dsPIC33EPXXX(MC/MU)806/810/814

Devices Only) ...........................................................81

Real-Time Clock and Calendar (RTCC)...................... 96

Reference Clock ....................................................... 106

SPI1, SPI2, SPI3 and SPI4......................................... 84

System Control ......................................................... 106

Timer1 through Timer9 ............................................... 70

UART1, UART2, UART3 and UART4......................... 83

USB OTG (dsPIC33EPMU806/810/814 and

PIC24EPGU806/810/814 Devices Only) ............ 88

Registers

ACLKCON3 (Auxiliary Clock Control 3).................... 188

ACLKDIV3 (Auxiliary Clock Divisor 3) ...................... 189

AD1CON2 (ADC1 Control 2) .................................... 419

AD1CSSH (ADC1 Input Scan Select High) .............. 427

AD2CON2 (ADC2 Control 2) .................................... 421

ADxCHS0 (ADCx Input Channel 0 Select) ............... 426

ADxCHS123 (ADCx Input Channel 1, 2, 3

Select) .............................................................. 425

ADxCON1 (ADCx Control 1)..................................... 417

ADxCON3 (ADCx Control 3)..................................... 423

ADxCON4 (ADCx Control 4)..................................... 424

ADxCSSL (ADCx Input Scan Select Low) ................ 427

ALCFGRPT (Alarm Configuration) ........................... 455

ALRMVAL (Alarm Minutes and Seconds,

ALRMPTR = 00) ............................................... 460

ALRMVAL (Alarm Month and Day Value,

ALRMPTR = 10) ............................................... 458

ALRMVAL (Alarm Weekday and Hours,

ALRMPTR = 01) ............................................... 459

ALTDTRx (PWMx Alternate Dead-Time).................. 310

AUXCONx (PWM Auxiliary Control x) ...................... 319

CHOP (PWM Chop Clock Generator) ...................... 303

CLKDIV (Clock Divisor) ............................................ 184

CMSTAT (Comparator Status) ................................. 440

CMxCON (Comparator x Control)............................. 441

CMxFLTR (Comparator x Filter Control)................... 447

CMxMSKCON (Comparator x Mask Gating

Control)............................................................. 445

CMxMSKSRC (Comparator x Mask Source

Select Control).................................................. 443

CORCON (Core Control) .................................... 44, 152

CRCCON1 (CRC Control 1) ..................................... 463

CRCCON2 (CRC Control 2) ..................................... 464

CRCXORH (CRC XOR Polynomial High)................. 465

CRCXORL (CRC XOR Polynomial Low) .................. 465

CVRCON (Comparator Voltage

Reference Control) ........................................... 448

CxBUFPNT1 (ECANx Filter 0-3 Buffer Pointer)........ 371

CxBUFPNT2 (ECANx Filter 4-7 Buffer Pointer)........ 372

CxBUFPNT3 (ECANx Filter 8-11 Buffer Pointer)...... 372

CxBUFPNT4 (ECANx Filter 12-15

Buffer Pointer) .................................................. 373

CxCFG1 (ECANx Baud Rate Configuration 1) ......... 369

CxCFG2 (ECANx Baud Rate Configuration 2) ......... 370

CxCTRL1 (ECANx Control 1) ................................... 362

CxCTRL2 (ECANx Control 2) ................................... 363

CxEC (ECANx Transmit/Receive Error Count)......... 369

CxFCTRL (ECANx FIFO Control)............................. 365

CxFEN1 (ECANx Acceptance Filter Enable)............ 371

CxFIFO (ECANx FIFO Status).................................. 366

CxFMSKSEL1 (ECANx Filter 7-0

Mask Selection) ................................................ 375

CxFMSKSEL2 (ECANx Filter 15-8

Mask Selection) ................................................ 376

CxINTE (ECANx Interrupt Enable) ........................... 368

CxINTF (ECANx Interrupt Flag)................................ 367

CxRXFnEID (ECANx Acceptance Filter n

Extended Identifier) .......................................... 375

 2009-2012 Microchip Technology Inc. DS70616G-page 613

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

CxRXFnSID (ECANx Acceptance Filter n

Standard Identifier) ........................................... 374

CxRXFUL1 (ECANx Receive Buffer Full 1) .............. 378

CxRXFUL2 (ECANx Receive Buffer Full 2) .............. 378

CxRXMnEID (ECANx Acceptance Filter Mask n

Extended Identifier)........................................... 377

CxRXMnSID (ECANx Acceptance Filter Mask n

Standard Identifier) ........................................... 377

CxRXOVF1 (ECANx Receive Buffer Overflow 1) ..... 379

CxRXOVF2 (ECANx Receive Buffer Overflow 2) ..... 379

CxTRmnCON (ECANx TX/RX Buffer m Control)...... 380

CxVEC (ECANx Interrupt Code) ............................... 364

DCICON1 (DCI Control 1)......................................... 431

DCICON2 (DCI Control 2)......................................... 432

DCICON3 (DCI Control 3)......................................... 433

DCISTAT (DCI Status).............................................. 434

DMAPPS (DMA Ping-Pong Status) .......................... 174

DMAPWC (DMA Peripheral Write

Collision Status)................................................ 169

DMARQC (DMA Request Collision Status) .............. 171

DMAxCNT (DMA Channel x Transfer Count) ........... 167

DMAxCON (DMA Channel x Control) ....................... 163

DMAxPAD (DMA Channel x Peripheral Address)..... 167

DMAxREQ (DMA Channel x IRQ Select) ................. 164

DMAxSTAH (DMA Channel x Start

Address A, High)............................................... 165

DMAxSTAL (DMA Channel x Start

Address A, Low) ............................................... 165

DMAxSTBH (DMA Channel x Start

Address B, High)............................................... 166

DMAxSTBL (DMA Channel x Start

Address B, Low) ............................................... 166

DSADRH (Most Recent DMA Data Space

High Address) ................................................... 168

DSADRL (Most Recent DMA Data Space

Low Address).................................................... 168

DTRx (PWMx Dead-Time) ........................................ 310

FCLCONx (PWMx Fault Current-Limit Control) ........ 315

I2CxCON (I2Cx Control) ........................................... 348

I2CxMSK (I2Cx Slave Mode Address Mask) ............ 352

I2CxSTAT (I2Cx Status) ........................................... 350

ICxCON1 (Input Capture x Control 1) ....................... 283

ICxCON2 (Input Capture x Control 2) ....................... 284

INDXxCNTH (Index Counter x High Word)............... 331

INDXxCNTL (Index Counter x Low Word) ................ 331

INDXxHLD (Index Counter x Hold) ........................... 332

INTCON1 (Interrupt Control 1).................................. 153

INTCON2 (Interrupt Control 2).................................. 155

INTCON3 (Interrupt Control 3).................................. 156

INTCON4 (Interrupt Control 4).................................. 156

INTTREG (Interrupt Control and Status)................... 157

INTxHLDH (Interval Timer x Hold High Word) .......... 335

INTxHLDL (Interval Timer x Hold Low Word) ........... 335

INTxTMRH (Interval Timer x High Word).................. 334

INTxTMRL (Interval Timer x Low Word) ................... 335

IOCONx (PWMx I/O Control) .................................... 312

LEBCONx (Leading-Edge Blanking Control) ............ 317

LEBDLYx (Leading-Edge Blanking Delay x)............. 318

MDC (PWM Master Duty Cycle) ............................... 304

NVMADR (Nonvolatile Memory Address) ................. 139

NVMADRU (Nonvolatile Memory

Upper Address)................................................. 139

NVMCON (Nonvolatile Memory (NVM) Control)....... 138

NVMKEY (Nonvolatile Memory Key) ........................ 139

OCxCON1 (Output Compare x Control 1) ................ 289

OCxCON2 (Output Compare x Control 2) ................ 291

OSCCON (Oscillator Control)................................... 182

OSCTUN (FRC Oscillator Tuning)............................ 187

PADCFG1 (Pad Configuration Control)............ 454, 476

PDCx (PWMx Generator Duty Cycle)....................... 307

PHASEx (PWMx Primary Phase Shift)..................... 308

PLLFBD (PLL Feedback Divisor) ............................. 186

PMADDR (Parallel Master Port Address)................. 473

PMAEN (Parallel Master Port Address Enable) ....... 474

PMCON (Parallel Master Port Control)..................... 469

PMD1 (Peripheral Module Disable Control 1) .......... 194

PMD2 (Peripheral Module Disable Control 2) .......... 196

PMD3 (Peripheral Module Disable Control 3) .......... 198

PMD4 (Peripheral Module Disable Control 4) .......... 200

PMD5 (Peripheral Module Disable Control 5) .......... 201

PMD6 (Peripheral Module Disable Control 6) .......... 203

PMD7 (Peripheral Module Disable Control 7) .......... 204

PMMODE (Parallel Master Port Mode) .................... 471

PMSTAT (Parallel Master Port Status)..................... 475

POSxCNTH (Position Counter x High Word) ........... 330

POSxCNTL (Position Counter x Low Word)............. 330

POSxHLD (Position Counter x Hold)........................ 330

PTCON (PWM Time Base Control) .......................... 297

PTCON2 (Primary Master Clock

Divider Select 2) ............................................... 299

PTPER (Primary Master Time Base Period) ............ 299

PWMCAPx (Primary PWMx Time Base Capture) .... 320

PWMCONx (PWMx Control) .................................... 305

QEIxCON (QEIx Control).......................................... 324

QEIxGECH (QEIx Greater Than or Equal Compare

High Word)............................................................. 334

QEIxGECL (QEIx Greater Than or Equal Compare

Low Word).............................................................. 334

QEIxICH (QEIx Initialization/Capture High Word) .... 332

QEIxICL (QEIx Initialization/Capture Low Word) ...... 332

QEIxIOC (QEIx I/O Control) ..................................... 326

QEIxLECH (QEIx Less Than or Equal Compare

High Word)............................................................. 333

QEIxLECL (QEIx Less Than or Equal Compare

Low Word).............................................................. 333

QEIxSTAT (QEIx Status).......................................... 328

RCFGCAL (RTCC Calibration and

Configuration) ................................................... 452

RCON (Reset Control).............................................. 143

REFOCON (Reference Oscillator Control) ............... 190

RPINR0 (Peripheral Pin Select Input 0) ................... 220

RPINR1 (Peripheral Pin Select Input 1) ................... 221

RPINR10 (Peripheral Pin Select Input 10) ............... 230

RPINR11 (Peripheral Pin Select Input 11) ............... 231

RPINR12 (Peripheral Pin Select Input 12) ............... 232

RPINR13 (Peripheral Pin Select Input 13) ............... 233

RPINR14 (Peripheral Pin Select Input 14) ............... 234

RPINR15 (Peripheral Pin Select Input 15) ............... 235

RPINR16 (Peripheral Pin Select Input 16) ............... 236

RPINR17 (Peripheral Pin Select Input 17) ............... 237

RPINR18 (Peripheral Pin Select Input 18) ............... 238

RPINR19 (Peripheral Pin Select Input 19) ............... 239

RPINR2 (Peripheral Pin Select Input 2) ................... 222

RPINR20 (Peripheral Pin Select Input 20) ............... 240

RPINR21 (Peripheral Pin Select Input 21) ............... 241

RPINR23 (Peripheral Pin Select Input 23) ............... 241

RPINR24 (Peripheral Pin Select Input 24) ............... 242

RPINR25 (Peripheral Pin Select Input 25) ............... 243

RPINR26 (Peripheral Pin Select Input 26) ............... 244

RPINR27 (Peripheral Pin Select Input 27) ............... 245

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 614  2009-2012 Microchip Technology Inc.

RPINR28 (Peripheral Pin Select Input 28) ................ 246

RPINR29 (Peripheral Pin Select Input 29) ................ 247

RPINR3 (Peripheral Pin Select Input 3) .................... 223

RPINR30 (Peripheral Pin Select Input 30) ................ 248

RPINR31 (Peripheral Pin Select Input 31) ................ 249

RPINR32 (Peripheral Pin Select Input 32) ................ 250

RPINR33 (Peripheral Pin Select Input 33) ................ 251

RPINR34 (Peripheral Pin Select Input 34) ................ 252

RPINR35 (Peripheral Pin Select Input 35) ................ 253

RPINR36 (Peripheral Pin Select Input 36) ................ 254

RPINR37 (Peripheral Pin Select Input 37) ................ 255

RPINR38 (Peripheral Pin Select Input 38) ................ 256

RPINR39 (Peripheral Pin Select Input 39) ................ 257

RPINR4 (Peripheral Pin Select Input 4) .................... 224

RPINR40 (Peripheral Pin Select Input 40) ................ 258

RPINR41 (Peripheral Pin Select Input 41) ................ 259

RPINR42 (Peripheral Pin Select Input 42) ................ 260

RPINR43 (Peripheral Pin Select Input 43) ................ 261

RPINR5 (Peripheral Pin Select Input 5) .................... 225

RPINR6 (Peripheral Pin Select Input 6) .................... 226

RPINR7 (Peripheral Pin Select Input 7) .................... 227

RPINR8 (Peripheral Pin Select Input 8) .................... 228

RPINR9 (Peripheral Pin Select Input 9) .................... 229

RPOR0 (Peripheral Pin Select Output 0) .................. 261

RPOR1 (Peripheral Pin Select Output 1) .................. 262

RPOR10 (Peripheral Pin Select Output 10) .............. 266

RPOR11 (Peripheral Pin Select Output 11) .............. 267

RPOR12 (Peripheral Pin Select Output 12) .............. 267

RPOR13 (Peripheral Pin Select Output 13) .............. 268

RPOR14 (Peripheral Pin Select Output 14) .............. 268

RPOR15 (Peripheral Pin Select Output 15) .............. 269

RPOR2 (Peripheral Pin Select Output 2) .................. 262

RPOR3 (Peripheral Pin Select Output 3) .................. 263

RPOR4 (Peripheral Pin Select Output 4) .................. 263

RPOR5 (Peripheral Pin Select Output 5) .................. 264

RPOR6 (Peripheral Pin Select Output 6) .................. 264

RPOR7 (Peripheral Pin Select Output 7) .................. 265

RPOR8 (Peripheral Pin Select Output 8) .................. 265

RPOR9 (Peripheral Pin Select Output 9) .................. 266

RSCON (DCI Receive Slot Control).......................... 435

RTCVAL (Minutes and Seconds Value,

RTCPTR = 00) .................................................. 457

RTCVAL (Month and Day Value,

RTCPTR = 10) .................................................. 456

RTCVAL (Weekday and Hours Value,

RTCPTR = 01) .................................................. 457

RTCVAL (Year Value Register, RTCPTR = 11)........ 456

SDCx (PWMx Secondary Duty Cycle) ...................... 307

SEVTCMP (PWM Primary Special

Event Compare)................................................ 300

SPHASEx (PWMx Secondary Phase Shift) .............. 309

SPIxCON1 (SPIx Control 1) ...................................... 341

SPIxCON2 (SPIx Control 2) ...................................... 343

SPIxSTAT (SPIx Status and Control) ....................... 339

SR (CPU Status)................................................. 42, 151

SSEVTCMP (PWM Secondary Special

Event Compare)................................................ 303

STCON (PWM Secondary Master Time Base

Control) ............................................................. 301

STCON2 (PWM Secondary Clock

Divider Select 2)................................................ 302

T1CON (Timer1 Control)........................................... 273

TRGCONx (PWMx Trigger Control).......................... 311

TRIGx (PWM Primary Trigger Compare Value)........ 314

TSCON (DCI Transmit Slot Control) ......................... 435

TxCON (T2CON, T4CON, T6CON or T8CON)

Control)............................................................. 278

TyCON (T3CON, T5CON, T7CON or T9CON)

Control)............................................................. 279

UxADDR (USB Address) .......................................... 394

UxBDTP1 (USB Buffer Description Table 1) ............ 408

UxBDTP2 (USB Buffer Description Table 2) ............ 408

UxBDTP3 (USB Buffer Description Table 3) ............ 409

UxCNFG1 (USB Configuration 1)............................. 395

UxCNFG2 (USB Configuration 2)............................. 396

UxCON (USB Control, Device Mode) ....................... 392

UxCON (USB Control, Host Mode)........................... 393

UxEIE (USB Error Interrupt Enable,

Device Mode) ................................................... 405

UxEIE (USB Error Interrupt Enable, Host Mode)...... 406

UxEIR (USB Error Interrupt Status,

Device Mode) ................................................... 403

UxEIR (USB Error Interrupt Status, Host Mode)....... 404

UxEPn (USB Endpoint n Control)............................. 407

UxFRMH (USB Frame Number High)....................... 410

UxFRML (USB Frame Number Low) ........................ 411

UxIE (USB Interrupt Enable, Device Mode).............. 401

UxIE (USB Interrupt Enable, Host Mode) ................. 402

UxIR (USB Interrupt Status, Device Mode Only) ...... 399

UxIR (USB Interrupt Status, Host Mode Only).......... 400

UxMODE (UARTx Mode).......................................... 355

UxOTGCON (USB OTG Control) ............................. 389

UxOTGIE (USB OTG Interrupt Enable,

Host Mode Only)............................................... 398

UxOTGIR (USB OTG Interrupt Status,

Host Mode Only)............................................... 397

UxOTGSTAT (USB OTG Status).............................. 388

UxPWMCON (USB VBUS PWM

Generator Control)............................................ 409

UxPWMRRS (Duty Cycle and PWM Period) ............ 410

UxPWRC (USB Power Control)................................ 390

UxSOF (USB OTG Start-of-Token Threshold,

Host Mode Only)............................................... 395

UxSTA (UARTx Status and Control)......................... 357

UxSTAT (USB Status) .............................................. 391

UxTOK (USB Token, Host Mode Only) .................... 394

VELxCNT (Velocity Counter x) ................................. 331

Resets............................................................................... 141

Brown-out Reset (BOR)............................................ 141

Configuration Mismatch Reset (CM)......................... 141

Illegal Condition Device Reset (IOPUWR)................ 141

Illegal Opcode........................................................... 141

Master Clear Pin Reset (MCLR ................................ 141

Power-on Reset (POR)............................................. 141

RESET Instruction (SWR) ........................................ 141

Security Reset .......................................................... 141

Trap Conflict Reset (TRAPR) ................................... 141

Uninitialized W Register............................................ 141

Watchdog Timer Reset (WDTO)............................... 141

Resources Required for Digital PFC............................. 34, 36

Revision History................................................................ 597

RTCC

Resources ................................................................ 451

Writing to the Timer .................................................. 451

 2009-2012 Microchip Technology Inc. DS70616G-page 615

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

Serial Peripheral Interface (SPI) ....................................... 337

Software Simulator (MPLAB SIM)..................................... 497

Software Stack Pointer, Frame Pointer

CALL Stack Frame.................................................... 128

Special Features

Code Protection ........................................................ 477

CodeGuard Security ................................................. 477

Flexible Configuration ............................................... 477

In-Circuit Emulation................................................... 477

In-Circuit Serial Programming (ICSP) ....................... 477

JTAG Boundary Scan Interface ................................ 477

Watchdog Timer (WDT) ............................................ 477

Special Features of the CPU ............................................ 477

SPI

Control Registers ...................................................... 339

Helpful Tips ............................................................... 338

Resources................................................................. 338

Symbols Used in Opcode Descriptions............................. 486

Timer1............................................................................... 271

Control Register ........................................................ 273

Timer2/3, Timer4/5, Timer6/7 and Timer8/9 ..................... 275

Timerx/y

Control Registers ...................................................... 278

Timing Diagrams

10-Bit ADC Conversion (CHPS<1:0> = 01, SIMSAM = 0,

ASAM = 0, SSRC<2:0> = 000, SSRCG = 0)....... 561

10-Bit ADC Conversion (CHPS<1:0> = 01, SIMSAM = 0,

ASAM = 1, SSRC<2:0> = 111, SSRCG = 0,

SAMC<4:0> = 00010)............................................ 561

12-Bit ADC Conversion (12-Bit Mode, ASAM = 0,

SSRC<2:0> = 000, SSRCG = 0)........................... 559

BOR and Master Clear Reset ................................... 517

DCI AC-Link Mode .................................................... 565

DCI Multi -Channel, I2S Modes................................. 563

ECAN I/O .................................................................. 554

External Clock........................................................... 512

High-Speed PWMx (dsPIC33EPXXX(MC/MU)806/

810/814 Devices) ................................................... 523

High-Speed PWMx Fault (dsPIC33EPXXX(MC/MU)

806/810/814 Devices)............................................ 523

I/O Pins ..................................................................... 515

I2Cx Bus Data (Master Mode) .................................. 550

I2Cx Bus Data (Slave Mode) .................................... 552

I2Cx Bus Start/Stop Bits (Master Mode) ................... 550

I2Cx Bus Start/Stop Bits (Slave Mode) ..................... 552

Input Capture (ICx) ................................................... 521

OCx/PWMx ............................................................... 522

Output Compare (OCx)............................................. 522

Parallel Master Port Read......................................... 570

Parallel Master Port Write ......................................... 571

Parallel Slave Port .................................................... 569

Power-on Reset ........................................................ 516

QEA/QEB Input......................................................... 524

QEI Module Index Pulse ........................................... 525

SPI1, SPI3 and SPI4 Master Mode (Full-Duplex,

CKE = 0, CKP = x, SMP = 1) ............................ 529

SPI1, SPI3 and SPI4 Master Mode (Full-Duplex,

CKE = 1, CKP = x, SMP = 1) ............................ 528

SPI1, SPI3 and SPI4 Master Mode (Half-Duplex,

Transmit Only, CKE = 0)................................... 526

SPI1, SPI3 and SPI4 Master Mode (Half-Duplex,

Transmit Only, CKE = 1)................................... 527

SPI1, SPI3 and SPI4 Slave Mode (Full-Duplex,

CKE = 0, CKP = 0, SMP = 0) ................................ 536

SPI1, SPI3 and SPI4 Slave Mode (Full-Duplex,

CKE = 0, CKP = 1, SMP = 0) ................................ 534

SPI1, SPI3 and SPI4 Slave Mode (Full-Duplex,

CKE = 1, CKP = 0, SMP = 0) ................................ 530

SPI1, SPI3 and SPI4 Slave Mode (Full-Duplex,

CKE = 1, CKP = 1, SMP = 0) ................................ 532

SPI2 Master Mode (Full-Duplex, CKE = 0,

CKP = x, SMP = 1) ................................................ 541

SPI2 Master Mode (Full-Duplex, CKE = 1,

CKP = x, SMP = 1) ................................................ 540

SPI2 Master Mode (Half-Duplex, Transmit Only,

CKE = 0) ................................................................ 538

SPI2 Master Mode (Half-Duplex, Transmit Only,

CKE = 1) ................................................................ 539

SPI2 Slave Mode (Full-Duplex, CKE = 0,

CKP = 0, SMP = 0) ................................................ 548

SPI2 Slave Mode (Full-Duplex, CKE = 0,

CKP = 1, SMP = 0) ................................................ 546

SPI2 Slave Mode (Full-Duplex, CKE = 1,

CKP = 0, SMP = 0) ................................................ 542

SPI2 Slave Mode (Full-Duplex, CKE = 1,

CKP = 1, SMP = 0) ................................................ 544

Timer1-Timer9 External Clock.................................. 518

TimerQ (QEI Module) External Clock ....................... 520

UARTx I/O ................................................................ 554

Timing Specifications

10-Bit ADC Conversion Requirements ..................... 562

12-Bit Mode ADC Conversion Requirements ........... 560

ADC .......................................................................... 556

ADC (10-Bit Mode) ................................................... 558

ADC (12-Bit Mode) ................................................... 557

Auxiliary PLL Clock................................................... 513

DCI AC-Link Mode.................................................... 566

DCI Multi-Channel, I2S Modes ................................. 564

DMA Module............................................................. 571

ECAN I/O.................................................................. 554

External Clock Requirements ................................... 512

High-Speed PWMx Requirements (dsPIC33EPXXX

(MC/MU)806/810/814 Devices)........................ 523

I2Cx Bus Data Requirements (Master Mode)........... 551

I2Cx Bus Data Requirements (Slave Mode)............. 553

Input Capture (ICx) Requirements............................ 521

OCx/PWMx Mode Requirements ............................. 522

Output Compare (OCx) Requirements ..................... 522

Parallel Master Port Read ........................................ 570

Parallel Master Port Write......................................... 571

Parallel Slave Port .................................................... 569

PLL Clock ................................................................. 513

QEI External Clock Requirements............................ 520

QEI Index Pulse Requirements ................................ 525

Quadrature Decoder Requirements ......................... 524

Reset, Watchdog Timer, Oscillator Start-up Timer,

Power-up Timer Requirements ............................. 517

SPI1, SPI3 and SPI4 Master Mode (Full-Duplex,

CKE = 0, CKP = x, SMP = 1) ................................ 529

SPI1, SPI3 and SPI4 Master Mode (Full-Duplex,

CKE = 1, CKP = x, SMP = 1) ................................ 528

SPI1, SPI3 and SPI4 Master Mode (Half-Duplex,

Transmit Only) ....................................................... 527

SPI1, SPI3 and SPI4 Maximum Data/Clock

Rate Summary....................................................... 526

SPI1, SPI3 and SPI4 Slave Mode (Full-Duplex,

CKE = 0, CKP = 0, SMP = 0) ................................ 537

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 616  2009-2012 Microchip Technology Inc.

SPI1, SPI3 and SPI4 Slave Mode (Full-Duplex,

CKE = 0, CKP = 1, SMP = 0) .................................535

SPI1, SPI3 and SPI4 Slave Mode (Full-Duplex,

CKE = 1, CKP = 0, SMP = 0) .................................531

SPI1, SPI3 and SPI4 Slave Mode (Full-Duplex,

CKE = 1, CKP = 1, SMP = 0) .................................533

SPI2 Master Mode (Full-Duplex, CKE = 0,

CKP = x, SMP = 1) .................................................541

SPI2 Master Mode (Full-Duplex, CKE = 1,

CKP = x, SMP = 1) .................................................540

SPI2 Master Mode (Half-Duplex, Transmit Only)...........539

SPI2 Slave Mode (Full-Duplex, CKE = 0,

CKP = 0, SMP = 0).................................................549

SPI2 Slave Mode (Full-Duplex, CKE = 0,

CKP = 1, SMP = 0).................................................547

SPI2 Slave Mode (Full-Duplex, CKE = 1,

CKP = 0, SMP = 0).................................................543

SPI2 Slave Mode (Full-Duplex, CKE = 1,

CKP = 1, SMP = 0).................................................545

Timer1 External Clock Requirements.............................518

Timer2, Timer4, Timer6, Timer8 External

Clock Requirements ...............................................519

Timer3, Timer5, Timer7, Timer9 External

Clock Requirements ...............................................519

UARTx I/O .......................................................................554

USB OTG (dsPIC33EPXXXMU8XX,

PIC24EPXXXGU8XX Devices) .............................555

UARTx

Control Registers...................................................... 355

Helpful Tips............................................................... 354

Resources ................................................................ 354

Universal Asynchronous Receiver

Transmitter (UART) .................................................. 353

USB On-The-Go (OTG) .................................................... 385

Clearing Interrupts .................................................... 385

Control Registers...................................................... 388

Overview................................................................... 385

Resources ................................................................ 387

Voltage Regulator (On-Chip) ............................................ 481

Watchdog Timer (WDT).................................................... 482

Programming Considerations ................................... 482

WWW Address ................................................................. 616

WWW, On-Line Support ..................................................... 20

 2009-2012 Microchip Technology Inc. DS70616G-page 617

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

THE MICROCHIP WEB SITE

Microchip provides online support via our WWW site at

www.microchip.com. This web site is used as a means

to make files and information easily available to

customers. Accessible by using your favorite Internet

browser, the web site contains the following

information:

•Product Support – Data sheets and errata,

application notes and sample programs, design

resources, user’s guides and hardware support

documents, latest software releases and archived

software

•General Technical Support – Frequently Asked

Questions (FAQs), technical support requests,

online discussion groups, Microchip consultant

program member listing

•Business of Microchip – Product selector and

ordering guides, latest Microchip press releases,

listing of seminars and events, listings of

Microchip sales offices, distributors and factory

representatives

CUSTOMER CHANGE NOTIFICATION

SERVICE

Microchip’s customer notification service helps keep

customers current on Microchip products. Subscribers

will receive e-mail notification whenever there are

changes, updates, revisions or errata related to a

specified product family or development tool of interest.

To register, access the Microchip web site at

www.microchip.com. Under “Support”, click on

“Customer Change Notification” and follow the

registration instructions.

CUSTOMER SUPPORT

Users of Microchip products can receive assistance

through several channels:

• Distributor or Representative

• Local Sales Office

• Field Application Engineer (FAE)

• Technical Support

• Development Systems Information Line

Customers should contact their distributor,

representative or field application engineer (FAE) for

support. Local sales offices are also available to help

customers. A listing of sales offices and locations is

included in the back of this document.

Technical support is available through the web site

at: http://microchip.com/support

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 618  2009-2012 Microchip Technology Inc.

READER RESPONSE

It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip

product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our

documentation can better serve you, please FAX your comments to the Technical Publications Manager at

(480) 792-4150.

Please list the following information, and use this outline to provide us with your comments about this document.

TO: Technical Publications Manager

RE: Reader Response

Total Pages Sent ________

From: Name

Company

Address

City / State / ZIP / Country

Telephone: (_______) _________ - _________

Application (optional):

Would you like a reply? Y N

Device: Literature Number:

Questions:

FAX: (______) _________ - _________

DS70616GdsPIC33EPXXX(GP/MC/MU)806/810/814 and

PIC24EPXXX(GP/GU)810/814

1. What are the best features of this document?

2. How does this document meet your hardware and software development needs?

3. Do you find the organization of this document easy to follow? If not, why?

4. What additions to the document do you think would enhance the structure and subject?

5. What deletions from the document could be made without affecting the overall usefulness?

6. Is there any incorrect or misleading information (what and where)?

7. How would you improve this document?

 2009-2012 Microchip Technology Inc. DS70616G-page 619

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

PRODUCT IDENTIFICATION SYSTEM

To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.

Architecture: 33 = 16-bit Digital Signal Controller

24 = 16-bit Microcontroller

Flash Memory Family: EP = Enhanced Performance

Product Group: MU8 = Motor Control family with USB

GU8 = General Purpose family with USB

Pin Count: 06 = 64-pin

10 = 100-pin, 121-pin

14 = 144-pin

Temperature Range: I=-40C to+85C (Industrial)

E=-40C to+125C (Extended)

Package: PT = 10x10 or 12x12 mm TQFP (Thin Quad Flatpack)

PF = 14x14 mm TQFP (Thin Quad Flatpack)

MR = 9x9 mm QFN (Plastic Quad Flatpack)

BG = 10x10 mm TFBGA (Plastic Thin Profile Ball Grid

Array )

PH = 16x16 mm TQFP (Thin Quad Flatpack)

PL = 20x20 mm LQFP (Low-Profile Quad Flatpack)

Examples:

a) dsPIC33EP512MU814T-E/PH:

Motor Control with USB dsPIC33,

512 KB program memory, 144-pin,

Extended temperature, TQFP package.

Microchip Trademark

Architecture

Flash Memory Family

Program Memory Size (KB)

Product Group

Pin Count

Temperature Range

Package

Pattern

dsPIC 33 EP 512 MU8 14 T -E / PH - XXX

Tape and Reel Flag (if applicable)

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814

DS70616G-page 620  2009-2012 Microchip Technology Inc.

NOTES:

 2009-2012 Microchip Technology Inc. DS70616G-page 621

Information contained in this publication regarding device

applications and the like is provided only for your convenience

and may be superseded by updates. It is your responsibility to

ensure that your application meets with your specifications.

MICROCHIP MAKES NO REPRESENTATIONS OR

WARRANTIES OF ANY KIND WHETHER EXPRESS OR

IMPLIED, WRITTEN OR ORAL, STATUTORY OR

OTHERWISE, RELATED TO THE INFORMATION,

INCLUDING BUT NOT LIMITED TO ITS CONDITION,

QUALITY, PERFORMANCE, MERCHANTABILITY OR

FITNESS FOR PURPOSE. Microchip disclaims all liability

arising from this information and its use. Use of Microchip

devices in life support and/or safety applications is entirely at

the buyer’s risk, and the buyer agrees to defend, indemnify and

hold harmless Microchip from any and all damages, claims,

suits, or expenses resulting from such use. No licenses are

conveyed, implicitly or otherwise, under any Microchip

intellectual property rights.

Trademarks

The Microchip name and logo, the Microchip logo, dsPIC,

FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro,

PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash

and UNI/O are registered trademarks of Microchip Technology

Incorporated in the U.S.A. and other countries.

FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,

MTP, SEEVAL and The Embedded Control Solutions

Company are registered trademarks of Microchip Technology

Incorporated in the U.S.A.

Silicon Storage Technology is a registered trademark of

Microchip Technology Inc. in other countries.

Analog-for-the-Digital Age, Application Maestro, BodyCom,

chipKIT, chipKIT logo, CodeGuard, dsPICDEM,

dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,

ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial

Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB

Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code

Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit,

PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O,

Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA

and Z-Scale are trademarks of Microchip Technology

Incorporated in the U.S.A. and other countries.

SQTP is a service mark of Microchip Technology Incorporated

in the U.S.A.

GestIC and ULPP are registered trademarks of Microchip

Technology Germany II GmbH & Co. & KG, a subsidiary of

Microchip Technology Inc., in other countries.

All other trademarks mentioned herein are property of their

respective companies.

Printed on recycled paper.

ISBN: 978-1-62076-624-8

Note the following details of the code protection feature on Microchip devices:

• Microchip products meet the specification contained in their particular Microchip Data Sheet.

• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the

intended manner and under normal conditions.

• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our

knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data

Sheets. Most likely, the person doing so is engaged in theft of intellectual property.

• Microchip is willing to work with the customer who is concerned about the integrity of their code.

• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not

mean that we are guaranteeing the product as “unbreakable.”

Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our

products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts

allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.

Microchip received ISO/TS-16949:2009 certification for its worldwide

headquarters, design and wafer fabrication facilities in Chandler and

Tempe, Arizona; Gresham, Oregon and design centers in California

and India. The Company’s quality system processes and procedures

are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping

devices, Serial EEPROMs, microperipherals, nonvolatile memory and

analog products. In addition, Microchip’s quality system for the design

and manufacture of development systems is ISO 9001:2000 certified.

QUALITY MANAGEMENT S

YSTEM

CERTIFIED BY DNV

== ISO/TS 16949 ==

DS70616G-page 622  2009-2012 Microchip Technology Inc.

AMERICAS

Corporate Office

2355 West Chandler Blvd.

Chandler, AZ 85224-6199

Tel: 480-792-7200

Fax: 480-792-7277

Technical Support:

http://www.microchip.com/

support

Web Address:

www.microchip.com

Atlanta

Duluth, GA

Tel: 678-957-9614

Fax: 678-957-1455

Boston

Westborough, MA

Tel: 774-760-0087

Fax: 774-760-0088

Chicago

Itasca, IL

Tel: 630-285-0071

Fax: 630-285-0075

Cleveland

Independence, OH

Tel: 216-447-0464

Fax: 216-447-0643

Dallas

Addison, TX

Tel: 972-818-7423

Fax: 972-818-2924

Detroit

Farmington Hills, MI

Tel: 248-538-2250

Fax: 248-538-2260

Indianapolis

Noblesville, IN

Tel: 317-773-8323

Fax: 317-773-5453

Los Angeles

Mission Viejo, CA

Tel: 949-462-9523

Fax: 949-462-9608

Santa Clara

Santa Clara, CA

Tel: 408-961-6444

Fax: 408-961-6445

Toronto

Mississauga, Ontario,

Canada

Tel: 905-673-0699

Fax: 905-673-6509

ASIA/PACIFIC

Asia Pacific Office

Suites 3707-14, 37th Floor

Tower 6, The Gateway

Harbour City, Kowloon

Hong Kong

Tel: 852-2401-1200

Fax: 852-2401-3431

Australia - Sydney

Tel: 61-2-9868-6733

Fax: 61-2-9868-6755

China - Beijing

Tel: 86-10-8569-7000

Fax: 86-10-8528-2104

China - Chengdu

Tel: 86-28-8665-5511

Fax: 86-28-8665-7889

China - Chongqing

Tel: 86-23-8980-9588

Fax: 86-23-8980-9500

China - Hangzhou

Tel: 86-571-2819-3187

Fax: 86-571-2819-3189

China - Hong Kong SAR

Tel: 852-2401-1200

Fax: 852-2401-3431

China - Nanjing

Tel: 86-25-8473-2460

Fax: 86-25-8473-2470

China - Qingdao

Tel: 86-532-8502-7355

Fax: 86-532-8502-7205

China - Shanghai

Tel: 86-21-5407-5533

Fax: 86-21-5407-5066

China - Shenyang

Tel: 86-24-2334-2829

Fax: 86-24-2334-2393

China - Shenzhen

Tel: 86-755-8203-2660

Fax: 86-755-8203-1760

China - Wuhan

Tel: 86-27-5980-5300

Fax: 86-27-5980-5118

China - Xian

Tel: 86-29-8833-7252

Fax: 86-29-8833-7256

China - Xiamen

Tel: 86-592-2388138

Fax: 86-592-2388130

China - Zhuhai

Tel: 86-756-3210040

Fax: 86-756-3210049

ASIA/PACIFIC

India - Bangalore

Tel: 91-80-3090-4444

Fax: 91-80-3090-4123

India - New Delhi

Tel: 91-11-4160-8631

Fax: 91-11-4160-8632

India - Pune

Tel: 91-20-2566-1512

Fax: 91-20-2566-1513

Japan - Osaka

Tel: 81-66-152-7160

Fax: 81-66-152-9310

Japan - Yokohama

Tel: 81-45-471- 6166

Fax: 81-45-471-6122

Korea - Daegu

Tel: 82-53-744-4301

Fax: 82-53-744-4302

Korea - Seoul

Tel: 82-2-554-7200

Fax: 82-2-558-5932 or

82-2-558-5934

Malaysia - Kuala Lumpur

Tel: 60-3-6201-9857

Fax: 60-3-6201-9859

Malaysia - Penang

Tel: 60-4-227-8870

Fax: 60-4-227-4068

Philippines - Manila

Tel: 63-2-634-9065

Fax: 63-2-634-9069

Singapore

Tel: 65-6334-8870

Fax: 65-6334-8850

Taiwan - Hsin Chu

Tel: 886-3-5778-366

Fax: 886-3-5770-955

Taiwan - Kaohsiung

Tel: 886-7-536-4818

Fax: 886-7-330-9305

Taiwan - Taipei

Tel: 886-2-2500-6610

Fax: 886-2-2508-0102

Thailand - Bangkok

Tel: 66-2-694-1351

Fax: 66-2-694-1350

EUROPE

Austria - Wels

Tel: 43-7242-2244-39

Fax: 43-7242-2244-393

Denmark - Copenhagen

Tel: 45-4450-2828

Fax: 45-4485-2829

France - Paris

Tel: 33-1-69-53-63-20

Fax: 33-1-69-30-90-79

Germany - Munich

Tel: 49-89-627-144-0

Fax: 49-89-627-144-44

Italy - Milan

Tel: 39-0331-742611

Fax: 39-0331-466781

Netherlands - Drunen

Tel: 31-416-690399

Fax: 31-416-690340

Spain - Madrid

Tel: 34-91-708-08-90

Fax: 34-91-708-08-91

UK - Wokingham

Tel: 44-118-921-5869

Fax: 44-118-921-5820

Worldwide Sales and Service

11/29/11