Thyristor Product Catalog L. U. D ZE NI 4 G 39 CO 716 E R #E d te ec l Se P * es ag k ac le Fi TO-220AB THERMOTAB TO-218AC TO-218X MT2 FASTPAK MT1 G Alternistor Triacs (6 - 40 Amps) 4 General Description Teccor offers bidirectional alternistors with current ratings from 6 to 40 amperes and voltages from 200 to 1000 volts as part of Teccor's broad line of thyristors. Teccor's alternistor has been specifically designed for applications that switch highly inductive loads. A special chip offers the same performance as two thyristors (SCRs) wired inverse parallel (back-to-back), providing better turn-off behavior than a standard triac. An alternistor may be triggered from a blocking to conduction state for either polarity of applied AC voltage with operating modes in Quadrants I, II, and III. This new chip construction provides two electrically separate SCR structures, providing enhanced dv/dt characteristics while retaining the advantages of a single chip device. All alternistors have glass-passivated junctions to ensure long term reliability and parameter stability. Teccor's glass offers a reliable barrier against junction contamination. Variations of devices covered in this data sheet are available for custom design applications. Please consult factory for further information. Features * * * * * High surge current capability Glass-passivated junctions 2500VAC isolation for "L," "J," "P," and "K" High commutating dv/dt High static dv/dt These alternistors are offered in TO-218X, TO-218AC, FastPak, and TO-220AB packages. Teccor's TO-218X package has been designed for heavy, steady power-handling capability. It features large eyelet terminals for ease of soldering heavy gauge hook-up wire. All the isolated packages have a standard isolation voltage rating of 2500VRMS. Teccor Electronics +1 972-580-7777 http://www.teccor.com 4-1 Alternistor Triacs Thyristor Product Catalog Part Number IT(RMS) Isolated Non-Isolated RMS On-State Current Conduction Angle of 360o (4)(16) MT2 MAX 10 Amps 12 Amps MT1 G MT2 THERMOTAB T0-220AB 8 Amps G IDRM VGT Peak Off-State Current Gate Open VDRM=Max Rated Value (1) (18) DC Gate Trigger Voltage VD=12VDC (2) (6) (15) (17) G G MT1 MT2 6 Amps DC Gate Trigger Current in Repetitive Specific Operating Peak Quadrants Blocking VD=12VDC Voltage (1) (3) (7) (15) (17) MT2 MT1 IGT VDRM TO-218AC (16) MT1 MT2 TO-218X MT1 FASTPAK TO-3 BASE G MT2 Volts See "Package Dimensions" section for variations. (11) QI MIN QII Volts mAmps mAmps TO-220AB QIII TC = 25C MAX TC = 100C TC = 125C MAX TC = 125C TC = 25C MIN MAX Q2006LH4 Q4006LH4 Q2006RH4 Q4006RH4 200 400 35 35 35 35 35 35 0.01 0.01 0.5 0.5 2.0 2.0 0.2 0.2 1.5 1.5 Q5006LH4 Q6006LH4 Q5006RH4 Q6006RH4 500 600 35 35 35 35 35 35 0.01 0.01 0.5 0.5 2.0 2.0 0.2 0.2 1.5 1.5 Q7006LH4 **Q8006LH4 Q7006RH4 **Q8006RH4 700 800 35 35 35 35 35 35 0.01 0.01 0.5 0.5 2.0 2.0 0.2 0.2 1.5 1.5 Q2008LH4 Q4008LH4 Q2008RH4 Q4008RH4 200 400 35 35 35 35 35 35 0.01 0.01 0.5 0.5 2.0 2.0 0.2 0.2 1.5 1.5 Q5008LH4 Q6008LH4 Q5008RH4 Q6008RH4 500 600 35 35 35 35 35 35 0.01 0.01 0.5 0.5 2.0 2.0 0.2 0.2 1.5 1.5 Q7008LH4 **Q8008LH4 Q7008RH4 **Q8008RH4 700 800 35 35 35 35 35 35 0.01 0.01 0.5 0.5 2.0 2.0 0.2 0.2 1.5 1.5 Q2010LH5 Q4010LH5 Q2010RH5 Q4010RH5 200 400 50 50 50 50 50 50 0.01 0.01 0.5 0.5 2.0 2.0 0.2 0.2 1.5 1.5 Q5010LH5 Q6010LH5 Q5010RH5 Q6010RH5 500 600 50 50 50 50 50 50 0.01 0.01 0.5 0.5 2.0 2.0 0.2 0.2 1.5 1.5 Q7010LH5 **Q8010LH5 Q7010RH5 **Q8010RH5 700 800 50 50 50 50 50 50 0.01 0.01 0.5 0.5 2.0 2.0 0.2 0.2 1.5 1.5 Q2012LH5 Q4012LH5 Q2012RH5 Q4012RH5 200 400 50 50 50 50 50 50 0.01 0.01 0.5 0.5 2.0 2.0 0.2 0.2 1.5 1.5 Q5012LH5 Q6012LH5 Q5012RH5 Q6012RH5 500 600 50 50 50 50 50 50 0.01 0.01 0.5 0.5 2.0 2.0 0.2 0.2 1.5 1.5 Q7012LH5 **Q8012LH5 Q7012RH5 **Q8012RH5 700 800 50 50 50 50 50 50 0.01 0.01 0.5 0.5 2.0 2.0 0.2 0.2 1.5 1.5 See General Notes and Electrical Specification Notes on page 6. ** Consult factory for 1000 volt device. http://www.teccor.com 4-2 Teccor Electronics +1 972-580-7777 Thyristor Product Catalog VTM IH Alternistor Triacs IGTM PGM PG(AV) Holding Peak Gate Peak Gate Average Peak Current Trigger Power Gate Power On-State (DC) Current Dissipation Dissipation Voltage at (14) (14) Max Rated Gate Open IGT IGTM RMS Current (1) (8) (12) TC = 25C (1) (5) ITSM dv/dt (c) Peak One Cycle Surge (9) (13) Critical Rate-of-Rise of Commutation Voltage at Rated VDRM and IT(RMS) Commutating di/dt = 0.54 Rated IT(RMS)/ms Gate Unenergized (1) (4) (13) Amps Amps 60Hz 50Hz di/dt Critical Gate Rate-of-Rise of Controlled Off-State Turn-On Voltage at Time Rated VDRM IGT = 300mA Gate Open 0.1s Rise (1) Time (10) Volts/Sec RMS Surge (NonRepetitive) On-State Current for period of 8.3 ms for Fusing Maximum Rate -ofChange of On-State Current (19) TC = 100C Amps2Sec Amps/Sec TC = 125C tgt Sec Volts mAmps MAX MAX 1.6 35 1.6 18 0.5 80 65 20 750 600 4 26.5 70 1.6 35 1.6 18 0.5 80 65 20 575 450 4 26.5 70 1.6 35 1.6 18 0.5 80 65 20 500 400 4 26.5 70 1.6 35 1.6 18 0.5 80 65 20 425 350 4 26.5 70 1.6 35 1.6 18 0.5 80 65 20 375 300 4 26.5 70 1.6 1.6 35 35 1.6 2.0 18 20 0.5 0.5 80 100 65 83 20 25 300 750 250 600 4 4 26.5 41 70 70 1.6 1.6 35 35 2.0 2.0 20 20 0.5 0.5 100 100 83 83 25 25 575 500 450 400 4 4 41 41 70 70 1.6 1.6 35 35 2.0 2.0 20 20 0.5 0.5 100 100 83 83 25 25 425 375 350 300 4 4 41 41 70 70 Watts Watts Volts/Sec I2 t dv/dt MIN MIN TYP 1.6 35 2.0 20 0.5 100 83 25 300 250 4 41 70 1.6 50 2.0 20 0.5 120 110 30 1150 1000 4 60 70 1.6 1.6 50 50 2.0 2.0 20 20 0.5 0.5 120 120 110 110 30 30 1000 925 750 700 4 4 60 60 70 70 1.6 1.6 50 50 2.0 2.0 20 20 0.5 0.5 120 120 110 110 30 30 850 775 650 600 4 4 60 60 70 70 1.6 1.6 50 50 2.0 2.0 20 20 0.5 0.5 120 120 110 110 30 30 650 1150 500 1000 4 4 60 60 70 70 1.6 1.6 50 50 2.0 2.0 20 20 0.5 0.5 120 120 110 110 30 30 1000 925 750 700 4 4 60 60 70 70 1.6 1.6 50 50 2.0 2.0 20 20 0.5 0.5 120 120 110 110 30 30 850 775 650 600 4 4 60 60 70 70 1.6 50 2.0 20 0.5 120 110 30 650 500 4 60 70 See General Notes and Electrical Specification Notes on page 6. Teccor Electronics +1 972-580-7777 http://www.teccor.com 4-3 Alternistor Triacs Thyristor Product Catalog Part Number IT(RMS) Isolated Non-Isolated RMS On-State Current Conduction Angle of 360o (4)(16) MT2 MAX MT1 G MT2 THERMOTAB T0-220AB 25 Amps G IDRM VGT Peak Off-State Current Gate Open VDRM=Max Rated Value (1) (18) DC Gate Trigger Voltage VD=12VDC (2) (6) (15) (17) G G MT1 MT2 16 Amps DC Gate Trigger Current in Repetitive Specific Operating Peak Quadrants Blocking VD=12VDC Voltage (1) (3) (7) (15) (17) MT2 MT1 IGT VDRM TO-218AC (16) MT1 MT2 TO-218X MT1 FASTPAK TO-3 BASE G MT2 Volts See "Package Dimensions" section for variations. (11) QI MIN QII Volts mAmps mAmps TO-220AB QIII TC = 25C MAX TC = 100C TC = 125C MAX TC = 125C TC = 25C MIN MAX Q2016LH3 Q4016LH3 Q2016RH3 Q4016RH3 200 400 20 20 20 20 20 20 .05 .05 0.5 0.5 2.0 2.0 0.2 0.2 1.5 1.5 Q5016LH3 Q6016LH3 Q5016RH3 Q6016RH3 500 600 20 20 20 20 20 20 .05 .05 0.5 0.5 2.0 2.0 0.2 0.2 1.5 1.5 Q7016LH3 **Q8016LH3 Q7016RH3 **Q8016RH3 700 800 20 20 20 20 20 20 0.1 0.1 1.0 1.0 3.0 3.0 0.2 0.2 1.5 1.5 Q2016LH4 Q4016LH4 Q2016RH4 Q4016RH4 200 400 35 35 35 35 35 35 .05 .05 0.5 0.5 2.0 2.0 0.2 0.2 2.0 2.0 Q5016LH4 Q6016LH4 Q5016RH4 Q6016RH4 500 600 35 35 35 35 35 35 .05 .05 0.5 0.5 2.0 2.0 0.2 0.2 2.0 2.0 Q7016LH4 **Q8016LH4 Q7016RH4 **Q8016RH4 700 800 35 35 35 35 35 35 0.1 0.1 1.0 1.0 3.0 3.0 0.2 0.2 2.0 2.0 Q2016LH6 Q4016LH6 Q2016RH6 Q4016RH6 200 400 80 80 80 80 80 80 .05 .05 0.5 0.5 2.0 2.0 0.2 0.2 2.5 2.5 Q5016LH6 Q6016LH6 Q5016RH6 Q6016RH6 500 600 80 80 80 80 80 80 .05 .05 0.5 0.5 2.0 2.0 0.2 0.2 2.5 2.5 Q7016LH6 **Q8016LH6 Q7016RH6 **Q8016RH6 700 800 80 80 80 80 80 80 0.1 0.1 1.0 1.0 3.0 3.0 0.2 0.2 2.5 2.5 Q2025L6 Q4025L6 Q2025K6 Q4025K6 Q2025J6 Q4025J6 Q2025P Q4025P Q2025R6 Q4025R6 200 400 80 80 80 80 80 80 .05 .05 0.5 0.5 2.0 2.0 0.2 0.2 2.5 2.5 Q5025L6 Q6025L6 Q5025K6 Q6025K6 Q5025J6 Q6025J6 Q5025P Q6025P Q5025R6 Q6025R6 500 600 80 80 80 80 80 80 .05 .05 0.5 0.5 2.0 2.0 0.2 0.2 2.5 2.5 Q7025L6 **Q8025L6 Q7025K6 **Q8025K6 Q7025J6 Q8025J6 Q7025P Q8025P Q7025R6 **Q8025R6 700 800 80 80 80 80 80 80 0.1 0.1 1.0 1.0 3.0 3.0 0.2 0.2 2.5 2.5 Q2040K7 Q4040K7 Q2040J7 Q4040J7 Q2040P Q4040P 200 400 100 100 100 100 100 100 0.2 0.2 2.0 2.0 5.0 5.0 0.2 0.2 2.5 2.5 Q5040K7 Q6040K7 Q5040J7 Q6040J7 Q5040P Q6040P 500 600 100 100 100 100 100 100 0.2 0.2 2.0 2.0 5.0 5.0 0.2 0.2 2.5 2.5 Q7040K7 **Q8040K7 Q7040J7 Q8040J7 Q7040P Q8040P 700 800 100 100 100 100 100 100 0.2 0.2 2.0 2.0 5.0 5.0 0.2 0.2 2.5 2.5 40 Amps See General Notes and Electrical Specification Notes on page 6. ** Consult factory for 1000 volt device http://www.teccor.com 4-4 Teccor Electronics +1 972-580-7777 Thyristor Product Catalog VTM IH Alternistor Triacs IGTM PGM PG(AV) Holding Peak Gate Peak Gate Average Peak Current Trigger Power Gate Power On-State (DC) Current Dissipation Dissipation Voltage at (14) (14) Max Rated Gate Open IGT IGTM RMS Current (1) (8) (12) TC = 25C (1) (5) ITSM dv/dt (c) Peak One Cycle Surge (9) (13) Critical Rate-of-Rise of Commutation Voltage at Rated VDRM and IT(RMS) Commutating di/dt = 0.54 Rated IT(RMS)/ms Gate Unenergized (1) (4) (13) Amps Amps 60Hz 50Hz di/dt Critical Gate Rate-of-Rise of Controlled Off-State Turn-On Voltage at Time Rated VDRM IGT = 300mA Gate Open 0.1s Rise (1) Time (10) Volts/Sec RMS Surge (NonRepetitive) On-State Current for period of 8.3 ms for Fusing Maximum Rate -ofChange of On-State Current (19) TC = 100C Amps2Sec Amps/Sec TC = 125C tgt Sec Volts mAmps MAX MAX 1.6 35 2.0 20 0.5 200 167 20 500 400 3 166 100 1.6 35 2.0 20 0.5 200 167 20 400 350 3 166 100 1.6 35 2.0 20 0.5 200 167 20 300 250 3 166 100 1.6 35 2.0 20 0.5 200 167 20 300 250 3 166 100 1.6 35 2.0 20 0.5 200 167 20 275 200 3 166 100 1.6 35 2.0 20 0.5 200 167 20 275 200 3 166 100 1.6 50 2.0 20 0.5 200 167 25 650 500 3 166 100 1.6 1.6 50 50 2.0 2.0 20 20 0.5 0.5 200 200 167 167 25 25 600 550 475 425 3 3 166 166 100 100 1.6 1.6 50 50 2.0 2.0 20 20 0.5 0.5 200 200 167 167 25 25 500 425 400 350 3 3 166 166 100 100 1.6 1.6 50 70 2.0 2.0 20 20 0.5 0.5 200 200 167 167 25 30 425 875 350 600 3 5 166 166 100 100 1.6 1.6 70 70 2.0 2.0 20 20 0.5 0.5 200 200 167 167 30 30 875 800 600 520 5 5 166 166 100 100 1.6 1.6 70 70 2.0 2.0 20 20 0.5 0.5 200 200 167 167 30 30 800 700 520 475 5 5 166 166 100 100 1.6 1.8 70 100 2.0 2.0 20 20 0.5 0.5 200 250 167 208 30 30 700 875 475 600 5 5 166 259 100 100 1.8 1.8 100 100 2.0 2.0 20 20 0.5 0.5 250 250 208 208 30 30 875 800 600 520 5 5 259 259 100 100 1.8 1.8 100 100 2.0 2.0 20 20 0.5 0.5 250 250 208 208 30 30 800 700 520 475 5 5 259 259 100 100 1.8 100 2.0 20 0.5 250 208 30 700 475 5 259 100 1.8 120 4.0 40 0.8 400 335 50 1100 700 5 664 150 1.8 1.8 120 120 4.0 4.0 40 40 0.8 0.8 400 400 335 335 50 50 1100 1000 700 625 5 5 664 664 150 150 1.8 1.8 120 120 4.0 4.0 40 40 0.8 0.8 400 400 335 335 50 50 1000 900 625 575 5 5 664 664 150 150 1.8 120 4.0 40 0.8 400 335 50 900 575 5 664 150 Watts Watts Volts/Sec I2 t dv/dt MIN MIN TYP See General Notes and Electrical Specification Notes on page 6. Teccor Electronics +1 972-580-7777 http://www.teccor.com 4-5 Alternistor Triacs Thyristor Product Catalog General Notes Gate Characteristics * All measurements are made at 60Hz with a resistive load at an ambient temperature of +25C unless specified otherwise. Teccor triacs may be turned on in the following ways: * Operating temperature range (TJ) is -40C to +125C except 0C to +125C for FastPaks. * Storage temperature range (TS) is -40C to +125C except -20C to +125C for FastPaks. * Lead solder temperature is a maximum of 230C for 10 seconds maximum 1/16" (1.59mm) from case. * The case temperature (TC) is measured as shown on the dimensional outline drawings. See "Package Dimensions" section of this catalog. * With in-phase signals (using standard AC line) Quadrants I and III are used. * By applying unipolar pulses (gate always negative)--with negative gate pulses Quadrants II and III are used. In all cases, if maximum surge capability is required, gate pulses should be a minimum of one magnitude above minimum IGT rating with a steep rising waveform (1s rise time). ALL POLARITIES ARE REFERENCED TO MT1 MT2 POSITIVE (Positive Half Cycle) MT2 MT2 + Electrical Specification Notes (1) For either polarity of MT2 with reference to MT1 terminal. (2) For either polarity of gate voltage (VGT) with reference to MT1 terminal. (3) See Definition of Quadrants. (4) See Figures 4.1 through 4.4 for current rating at specific operating temperature and Figure 4.16 for free air rating (no heat sink). (5) See Figures 4.5 and 4.6 for iT and vT. (6) See Figure 4.7 for VGT vs TC. (7) See Figure 4.8 for IGT vs TC. (8) See Figure 4.9 for IH vs TC. (9) See Figures 4.10 and 4.11 for surge rating with specific durations. (10) See Figure 4.12 for tgt vs IGT. (-) IGT GATE (+) IGT GATE MT1 IGT REF - MT2 (-) MT1 QII QI QIII QIV (+) MT1 + IGT MT2 IGT GATE REF REF IGT GATE MT1 - REF MT2 NEGATIVE (Negative Half Cycle) NOTE: Alternistors will not operate in QIV Definition of Quadrants (11) See package outlines for lead form configurations. When ordering special lead forming, add type number as suffix to part number. Electrical Isolation (12) Initial on-state current = 400 mA(DC) for 16-40A devices and 100mA for 6-12 Amp devices. Teccor's isolated Alternistor packages will withstand a minimum high potential test of 2500 VAC (RMS) from leads to mounting tab, over the operating temperature range of the device. See isolation table below for standard and optional isolation ratings. (13) See Figures 4.1 through 4.4 for maximum allowable case temperature at maximum rated current. (14) Pulse width 10s. (15) For 6-12 Amp devices, RL = 60; 16 Amp and above, RL = 30 ELECTRICAL ISOLATION FROM LEADS TO MOUNTING TAB ** (16) 40 Amp pin terminal leads on K package can run 100C to 125C. (17) Alternistor does not turn on in Quadrant IV. (18) Tc = TJ for test conditions in off-state (19) IGT = 200 mA for 6-12 Amp devices and 500 mA for 16-40 Amp devices with gate pulse having rise time of 0.1 microsecond. VAC (RMS) 2500 4000 Isolated TO-218AC Isolated FASTPAK Isolated TO-220AB Isolated TO-218X Standard N/A Standard Standard Standard N/A Optional * N/A * For 4000V isolation, use V suffix in part number. ** UL Recognized File E71639 http://www.teccor.com 4-6 Teccor Electronics +1 972-580-7777 Thyristor Product Catalog Alternistor Triacs THERMAL RESISTANCE (Steady State) R JC [R JA] (TYP.) C/W K P L R J MT2 MT2 G MT1 Type MT1 MT1 MT2 Isolated** TO-218AC 6 amps 8 amps 10 amps 12 amps 16 amps 25 amps 40 amps G G MT1 G MT2 FastPak** TO-3BASE 1.35 0.97 1.3 0.9 Isolated** THERMOTAB TO-220AB 3.3 [50] 2.8 2.6 2.3 2.1 2.0 G MT1 MT2 Non-Isolated TO-220AB MT2 Isolated** TO-218X 2.1 [45] 1.8 1.5 1.4 1.3 1.1 1.32 0.95 ** UL Recognized Product per UL File E71639. 10 AMP TO-220 (NON-ISOLATED) 120 Maximum Allowable Case Temperature (T C )-- C Maximum Allowable Case Temperature (TC) - C 130 130 12 AMP TO-220 (ISOLATED) 110 100 6 AMP TO-220 (NON-ISOLATED) 90 6 AMP TO -220 (ISOLATED) 80 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360 CASE TEMPERATURE: Measured as shown on Dimensional Drawing 70 60 120 16 16 100 4 6 8 PT O-2 P TO 20 -22 0 (NO (IS N-I OL SO AT E L AT ED ) D) 80 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTIVE ANGLE: 360 CASE TEMPERATURE: Measured as shown on Dimensional Drawing 70 60 0 0 2 AM 90 0 0 AM 110 10 12 14 5 10 15 RMS On-State Current [I T(RMS) ] -- Amps RMS On-State Current [lT(RMS)] - AMPS Figure 4.1 Figure 4.3 Maximum Allowable Case Temperature vs On-State Current (6-12 Amp Devices) 130 Maximum Allowable Case Temperature (TC) - C 12 AMP TO-220 (NON-ISOLATED) 110 100 8 AMP TO-220 (NON-ISOLATED) 90 8 AMP TO-220 (ISOLATED) 80 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360 CASE TEMPERATURE: Measured as shown on Dimensional Drawing 70 60 Maximum Allowable Case Temperature (TC) - C 130 10 AMP TO-220 (ISOLATED) 120 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360 CASE TEMPERATURE: Measured as shown on Dimensional Drawing 120 110 100 40 AMP FASTPAK & TO-218 (ISOLATED) 90 80 25 AMP FASTPAK TO-220 (NON-ISOLATED) & TO-218 (ISOLATED) 70 25 AMP TO-220 (ISOLATED) 60 0 0 0 2 4 6 8 10 12 0 14 Maximum Allowable Case Temperature vs On-State Current (8-12 Amp Devices) Teccor Electronics +1 972-580-7777 10 20 30 40 50 RMS On-State Current [lT(RMS)] - AMPS RMS On-State Current [lT(RMS)] - AMPS Figure 4.2 Maximum Allowable Case Temperature vs On-State Current (16 Amp Devices) Figure 4.4 Maximum Allowable Case Temperature vs On-State Current (25 and 40 Amp Devices) http://www.teccor.com 4-7 Alternistor Triacs Thyristor Product Catalog 20 4.0 TC = 25C 12 I GT 14 6 to 12 Amp Devices 10 8 6 3.0 2.0 Ratio of On-State Current (iT)--Amps Positive or Negative Instantaneous 16 I GT (T C =25C) 18 4 2 1.0 0 0 0.8 0.6 1.0 1.2 1.4 0 -65 1.6 -40 -15 +25 +65 +125 Case Temperature (T C ) -- C Positive or Negative Instantaneous On-State Voltage (v )--Volts T Figure 4.5 On-State Current vs On-State Voltage (Typical) (6-12 Amp Devices) Figure 4.8 Normalized DC Gate Trigger Current for all Quadrants vs Case Temperature 90 4.0 TC = 25C 70 IH 60 40 AMP 50 25 AMP Ratio of 40 I H (T C =25C) Positive or Negative Instantaneous On-State Current (iT)--Amps 80 30 20 16 AMP INITIAL ON-STATE CURRENT = 400mA (DC) 16-40A devices = 100mA (DC) 6-12A devices 3.0 2.0 1.0 10 0 -65 0 0.6 0 1.0 0.8 1.2 1.4 1.6 1.8 Figure 4.6 Figure 4.9 On-State Current vs On-State Voltage (Typical) (16-40 Amp Devices) 1.5 1.0 .5 -40 -15 +25 +65 +125 Case Temperature (T C ) -- C Normalized DC Gate Trigger Voltage for all Quadrants vs Case Temperature http://www.teccor.com 4-8 +25 +65 +125 Normalized DC Holding Current vs Case Temperature NOTES: 1) GATE CONTROL MAY BE LOST DURING AND IMMEDIATELY FOLOWING SURGE CURRENT INTERVAL. 2) OVERLOAD MAY NOT BE REPEATED UNTIL JUNCTION TEMPERATURE HAS RETURNED TO STEADY STATE RATED VALUE. 10-12 Amp Device 120 100 80 60 50 40 30 8 Amp Device 20 6 Amp Device 10 8 6 5 4 3 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS ON-STATE CURRENT [IT(RMS)]: Maximum Rated Value at Specified Case Temperature 2 Figure 4.7 -15 200 Peak Surge (Non-Repetitive) On-State Current (ITSM) -- Amps V GT (T C =25C) Ratio of V GT 2.0 0 -65 -40 Case Temperature (T C ) -- C Positive or Negative Instantaneous On-State Voltage (vT)--Volts 1 1 2 3 4 5 6 8 10 20 30 40 60 80 100 200 300 600 1000 Surge Current Duration -- Full Cycles Figure 4.10 Peak Surge Current vs Surge Current Duration (6-12 Amp Devices) Teccor Electronics +1 972-580-7777 Thyristor Product Catalog Alternistor Triacs 18 CURRENT WAVEFORM: Sinusoidal SUPPLY FREQUENCY: 60Hz Sinusoidal LOAD: Resistive RMS ON-STATE CURRENT [I T ( RMS ) ]: Maximum Rated Value at Specified Case Temperature 400 300 250 200 Average On-State Power Dissipation [P ]--Watts D (AV) Peak Surge (Non-Repetitive) On-State Current (I TSM )--Amps 1000 25 A MP 40 A MP 100 80 60 50 40 NOTES: 1) GATE CONTROL MAY BE LOST DURING AND IMMEDIATELY FOLLOWING SURGE CURRENT INTERVAL. 2) OVERLOAD MAY NOT BE REPEATED UNTIL JUNCTION TEMPERATURE HAS RETURNED TO STEADY-STATE RATED VALUE. 30 20 16 A M P 16 LOAD: Resistive or inductive 12 10 10 100 6 4 2 0 1000 Surge Current Duration -- Full Cycles Figure 4.11 Average On-State Power Dissipation [P ]--Watts D(AV) Typical Turn-On Time (t gt )--Sec 45 8 = 80-100ma 6 4 Devices with I GT = 50mA 2 Devices with I 0 = 20 - 35mA GT 200 100 300 400 35 Turn-On Time vs Gate Trigger Current (Typical) 6 8 10 14 12 T(RMS) 16 ] -- Amps 30 25 25 AMP 20 40 AMP 15 10 5 500 0 4 8 12 16 20 24 28 32 36 40 RMS On-State Current [I DC Gate Trigger Current ( I GT )--mA Figure 4.12 4 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360 40 0 0 2 Figure 4.14 Power Dissipation (Typical) vs On-State Current (16 Amp Devices) 10 GT 0 RMS On-State Current [I Peak Surge Current vs Surge Current Duration (16-40 Amp Devices) Devices with I 16 AMP 8 10 1 CONDUCTION ANGLE: 360 14 T(RMS) ]--Amps Figure 4.15 Power Dissipation (Typical) vs On-State Current (25 and 40 Amp Devices) 18 120 14 12 10 8 6 - 12 AMP 6 4 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360 2 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Maximum Allowable Ambient Temperature (TA) -- C Average On-State Power Dissipation [PD(AV)]--Watts 16 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360 FREE AIR RATING - NO HEATSINK 100 80 TO-220 DEVICES 60 40 25 20 0 RMS On-State Current [lT(RMS)]--AMPS Figure 4.13 Power Dissipation (Typical) vs On-State Current (6-12 Amp Devices) Teccor Electronics +1 972-580-7777 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 RMS On-State Current [IT (RMS)] -- Amps Figure 4.16 Maximum Allowable Ambient Temperature vs On-State Current http://www.teccor.com 4-9