E Series OMNI-BEAMTM Sensors OMNI-BEAM sensors with electromagnetic relay outputs Features * SPDT electromechanical relay output for economy and high switching capacity * Operate from 24 to 250V ac (50/60Hz) or from 24 to 36V dc; all sensing modes available * Modular design with interchangeable components, optional Pulse or Delay timing logic modules * Sense and Load output indicator LEDs * Choice of prewired cable or SO-type quick-disconnect cable fitting * Cross-hole design for front, back, or side mounting, plus 30mm threaded base mounting hub. Standard limit switch mounting hole spacing. (R) E71083 Sensor Head Models LR41887-17 Sensing Mode Range Beam Excess Gain Beam Pattern OSBE & OSBR Opposed Mode OSBE and OSBR Opposed Mode 1000 45 m (150`) OSEE, OSER OPPOSED Response: 20 ms ON/OFF Repeatability: 0.4 ms Infrared 880 nm E X C E S S G A I N 100 1500 mm 60 in 1000 mm 40 in 500 mm 20 in 0 10 1 0.1 m 0.33 ft 0 500 mm 20 in 1000 mm 40 in 1500 mm 60 in 0 1m 3.3 ft 10 m 33 ft 100 m 330 ft 10 m 30 ft OSED Diffuse Mode OSED DIFFUSE Response: 20 ms ON/OFF Repeatability: 1 ms Infrared 880 nm G A I N 50 m 150 ft OSED 100 7.5 mm 0.3 in 5.0 mm 0.2 in 2.5 mm 0.1 in 0 10 0 2.5 mm 0.1 in 5.0 mm 0.2 in 7.5 mm 1 1 mm .04 in 40 m 120 ft Diffuse Mode 1000 450 mm (18'') 30 m 90 ft DISTANCE DISTANCE E X C E S S 20 m 60 ft 0.3 in 0 10 mm .4 in 100 mm 4 in 1000 mm 40 in 100 mm 4 in 200 mm 8 in 300 mm 12 in 400 mm 500 mm 16 in 20 in DISTANCE DISTANCE WARNING . . . Not To Be Used for Personnel Protection Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death. These sensors do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Consult your current Banner Safety Products catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection. Printed in USA 04/08 P/N 03540 rev. C E Series OMNI-BEAMTM Sensors Models, continued Sensor Head Models Sensing Mode Range Beam Excess Gain Beam Pattern OSBDX 1000 2m (6') OSEDX DIFFUSE Response: 20 ms ON/OFF Repeatability: 1 ms Infrared 880 nm E X C E S S G A I N Diffuse Mode OSBDX Diffuse Mode 100 75 mm 3.0 in 50 mm 2.0 in 25 mm 1.0 in 0 10 1 0.01 m 0.033 ft 0 25 mm 1.0 in 50 mm 2.0 in 75 mm 3.0 in 0 0.1 m 0.33 ft 1.0 m 3.3 ft 10 m 33 ft 0.4 m 1.25 ft DISTANCE OSELV RETRO Response: 20 ms ON/OFF Repeatability: 1 ms Visible red 650 nm G A I N 1.6 m 5.0 ft 2.0 m 6.25 ft OSBLV 1000 0.15 to 9 m (6'' to 3') 1.2 m 3.75 ft DISTANCE Retroreflective Mode OSBLV E X C E S S 0.8 m 2.5 ft Retroreflective Mode 100 150 mm 6.0 in 100 mm 4.0 in 50 mm 2.0 in 0 With BRT-3 Reflector 0 50 mm 10 2.0 in 100 mm 4.0 in With BRT-3 Reflector 150 mm 1 .01 m .033 ft 6.0 in 0 .10 m .33 ft 1.0 m 3.3 ft 10 m 33 ft 2m 6.6 ft 4m 13 ft 6m 20 ft 8m 26 ft 10 m 33 ft DISTANCE DISTANCE OSBLVAG 1000 OSELVAG P POLAR RETRO Anti-Glare 0.3 to 4.5 m (12'' to 15') Response: 20 ms ON/OFF Repeatability: 1 ms Visible red 650 nm E X C E S S G A I N Retroreflective Mode OSBLVAG Retroreflective Mode 100 W/BRT-3 Reflector 3.0 in 50 mm 2.0 in 25 mm 1.0 in 0 0 25 mm 10 1 .01 m .033 ft 75 mm 50 mm 2.0 in 75 mm 3.0 in 0 .10 m .33 ft 1.0 m 3.3 ft 1.0 in With BRT-3 Reflector 10 m 33 ft 1m 3.3 ft 2m 6.6 ft 3m 10 ft 4m 13 ft 5m 16 ft DISTANCE DISTANCE OSBCV Convergent Mode OSBCV Convergent Mode 1000 Focus at 38 mm (1.5'') OSECV CONVERGENT Response: 20 ms ON/OFF Repeatability: 1 ms Visible Red 650 nm E X C E S S G A I N 100 2.4 mm 0.09 in 1.6 mm 0.06 in 0.8 mm 0.03 in 0 10 0 0.8 mm 0.03 in 1.6 mm 0.06 in 2.4 mm 1 1 mm .04 in 0.09 in 0 10 mm .4 in 100 mm 4 in 1000 mm 40 in 12.5 mm 0.50 in 25 mm 1.0 in 37.5 mm 1.5 in 50 mm 2.0 in 62.5 mm 2.5 in DISTANCE DISTANCE 2 P/N 03540 rev. C Banner Engineering Corp. * Minneapolis, MN U.S.A www.bannerengineering.com * Tel: 763.544.3164 E Series OMNI-BEAMTM Sensors Models, continued Sensor Head Models Sensing Mode Range Beam Excess Gain Beam Pattern OSBFX OSEFX Opposed Mode Opposed Mode 1000 E X C E S S Infrared 880 nm GLASS FIBER Opposed Mode 150 mm 100 4.0 in 50 mm 2.0 in 0 IT23S fibers G A I N 0 IT13S Fibers 50 mm 10 IT13S fibers 0.1 m 0.33 ft 1.0 m 3.3 ft 4.0 in 150 mm 6.0 in 10 m 33 ft 0.4 m 15 in DISTANCE Diffuse Mode Response: 20 ms ON/OFF Repeatability: 1 ms Infrared 880 nm GLASS FIBER 100 0.15 in PLASTIC FIBER Opposed Mode G A I N 10 0.05 in 2.5 mm 0.10 in 0.15 in 0 10 mm 0.4 in 100 mm 4.0 in 1000 mm 40 in 25 mm 1 in 50 mm 2 in 75 mm 3 in 100 mm 125 mm 4 in 5 in DISTANCE Opposed Mode Plastic Fibers OSBFP Opposed Mode 100 45 mm 1.8 in 30 mm 1.2 in 15 mm 0.6 in 0 PIT46U Fibers 10 PIT26U Fibers 100 mm 4.0 in 0 15 mm 0.6 in 30 mm 1.2 in 45 mm 1.8 in 0 10 mm .40 in PIT46U PIT26U 1000 mm 40 in 25 mm 1 in 50 mm 2 in 75 mm 3 in 100 mm 125 mm 4 in 5 in DISTANCE DISTANCE OSBFP OSEFP Diffuse Mode Response: 20 ms ON/OFF Repeatability: 1 ms PLASTIC FIBER Diffuse Mode Visible Red 650 nm E X C E S S G A I N 3.8 mm 0.15 in 2.5 mm 100 PBT46U Fiber 10 0.10 in BT13S Fiber 1.3 mm 0.05 in BT23S Fiber 0 0 1.3 mm 0.05 in 2.5 mm 0.10 in 3.8 mm 0.15 in PBT26U Fiber 0 1 mm .04 in 10 mm .4 in DISTANCE Banner Engineering Corp. * Minneapolis, MN U.S.A www.bannerengineering.com * Tel: 763.544.3164 OSBFX Diffuse Mode 1000 1 .1 mm .004 in 0 1.3 mm 3.8 mm BT13S Fiber 1 1 mm .04 in See Excess Gain curves 0.05 in BT23S Fiber 0 DISTANCE OSBFP Visible Red 650 nm 0.10 in BT13S Fiber 1.3 mm BT23S Fiber 1000 2.0 m 75 in OSBFX 2.5 mm 1 1 mm 0.04 in E X C E S S 1.6 m 60 in 3.8 mm G A I N Diffuse Mode 1.2 m 45 in Diffuse Mode 1000 E X C E S S 0.8 m 30 in DISTANCE OSBFX OSEFX 2.0 in 100 mm 0 1 0.01 m 0.03 ft See Excess Gain curves 6.0 in IT23S Fibers 100 mm 100 mm 4 in 25 mm 1 in 50 mm 2 in 75 mm 3 in 100 mm 125 mm 4 in 5 in DISTANCE P/N 03540 rev. C 3 E Series OMNI-BEAMTM Sensors Power Block Models OPEJ5 For Use With All but emitters OPEJ5QD OPEJE OPEJEQD Cable or Connector Prewired 6-foot PVC-jacketed 5-conductor cable. Integral minifastTM 5-conductor quick-disconnect cable fitting. Requires cable model MBCC-512, sold separately. Emitters only, no output circuitry Prewired 6-foot PVC-jacketed 2-conductor cable. Integral minifastTM 5-conductor quick-disconnect cable fitting. Requires cable model MBCC-512, sold separately. Overview Banner E Series OMNI-BEAMTM sensors are a line of modular, self-contained photoelectric sensors designed for applications where economy and performance are important. E Series OMNI-BEAMs have SPDT (single-pole double-throw, form "C") electromechanical relay output and employ a power block that operates from either 24 to 250V ac or 24 to 36V dc. Sensing ranges of E Series OMNI-BEAMs are in most cases identical to those of standard model OMNI-BEAMs. E Series OMNI-BEAM sensors have two major modules: a sensor head and a power block. (NOTE: sensor heads are interchangeable and are ordered individually.) LIGHT or DARK operate output is selected via an easily-accessible internal switch. LED indicators for Sense and Load are located atop the sensor head beneath a transparent gasketed acrylic cover. Optional logic module boards slip easily into the sensor head and provide adjustable delay or adjustable pulse timer logic. The Sense indicator lights whenever an object is sensed. The LOAD indicator lights whenever the sensor's output relay is energized. This indicator is especially useful when a timing logic module is used and SENSE and LOAD conditions are not concurrent. Their cross-hole mounting design with standard limit-switch hole spacing enables OMNI-BEAM E Series sensors to be mounted from the front, either side, or the back, making them ideal for conveyor and other production line applications. E Series OMNI-BEAMs may also be mounted using their 30mm threaded base mounting hub. A versatile 2-axis stainless steel accessory mounting bracket (model SMB30MM) and a PBT swivel-mount bracket (model SMB30SM) are available. E Series opposed mode emitters use an emitter power block, either model OPEJE or OPEJEQD. All other E Series sensors use either model OPEJ5 or OPEJ5QD*. Models OPEJE and OPEJ5 have a 1/2'' NPS integral internal conduit thread and are supplied with a 6-foot PVC-covered cable. Models OPEJEQD and OPEJ5QD ("QD" models) have NEMA 4-rated quick-disconnect Mini-style connectors. All models are housed in tough, molded PBT housings. The power block electronics are epoxy-encapsulated. When assembled, all parts of E Series OMNI-BEAMs are fully gasketed. Diffuse Mode Diffuse (proximity) mode sensors detect objects by sensing their own emitted light reflected from the object. They are ideal for use when the reflectivity and profile of the detected object is sufficient to return a large percentage of emitted light back to the sensor. Model OSEDX is the first choice for diffuse (proximity) mode applications when there are no background objects to falsely return light. Retroreflective The visible red sensing beam of retroreflective sensors makes them very easy to align. The anti-glare model (suffix "AG") polarizes the emitted light and filters out unwanted reflections, making sensing possible in otherwise unsuitable applications. Use "AG" models only in very clean environments and use with the model BRT-3 3'' reflector. For detailed information on retroreflective targets, see the Banner Sensor catalog. Fiber Optic Model OSEFX is an excellent choice for glass fiber optic applications compatible with the use of an infrared sensing beam and where faster sensor response is not required. Excess gain is very high; as a result, opposed individual fibers operate reliably in many hostile environments. Also, special miniature bifurcated fiber optic assemblies with bundle sizes as small as 0.5 mm (0.020'') in diameter may be used successfully for diffuse mode sensing. The excess gain curves and beam patterns illustrate response with standard 1.5 mm (0.060'') diameter and 3 mm (0.12'') diameter bundles. Response for smaller or larger bundle sizes may be interpolated. Plastic fiber optics are lower in cost than glass fiber optics and are ideal for use in situations where the environmental conditions allow. They are easily cut to length in the field and are available in a variety of sensing end styles. For further information, refer to the Banner sensor catalog. * NOTE: E Series sensor heads may also be used with Standard OMNI-BEAM power blocks with solid-state output relay. 4 P/N 03540 rev. C Banner Engineering Corp. * Minneapolis, MN U.S.A www.bannerengineering.com * Tel: 763.544.3164 E Series OMNI-BEAMTM Sensors Overview, continued Chemical resistance of plastic fiber optic assemblies: contact with acids, strong bases (alkalis), and solvents will damage the monofilament optical fiber acrylic core. The polyethylene jacket protects the optical fiber from most chemical environments; however, materials may migrate through the jacket with long-term exposure. Samples of plastic fiber optic material are available from Banner for testing and evaluation. Power Blocks with SPDT Form "C" Electromechanical Relay Output OMNI-BEAM E Series power blocks provide regulated low voltage dc power to the sensor head and logic module (if one is used), with input of 24 to 36V dc or 24 to 250V ac (50/60Hz). All power blocks, except those designed only to power emitters, have an internal electromechanical form "C" SPDT relay output. Power blocks are epoxy-encapsulated and rated for 0 to +50 C (+32 to +122 F). They feature limit switch style cross-hole design for front, back, or side mounting, plus a 30 mm threaded hub for swivel bracket or through-hole mounting. Models include prewired cable or quick-disconnect (QD) fitting (see models table). Assembled sensors are rated NEMA 1, 2, 3, 3S, 4, 12, and 13. Emitter Hookup to OPEJE and OPEJEQD Power Blocks L1 L2 24 to 36V dc or 24 to 250V ac Power Blocks: OPEJE OPEJEQD Sensor Block: OSEE Brown Emitter Hookup to OPEJ5 and OPEJ5QD Power Blocks L1 L2 24 to 36V dc or 24 to 250V ac Power Blocks: OPEJ5 OPEJ5QD Sensor Block: OSECV, OSED,OSEDX OSEFP, OSEFX, OSELV, OSELVAG, OSER Blue DC hookup is without regard to power supply polarity. Functional Schematic OPEJ5 and OPEJ5QD Power Blocks Brown (n.c. contact) White Blue Black (n.o. contact) Yellow (relay common) DC hookup is without regard to power supply polarity. Note: Cordset model MBCC-5.. is sold separately for use with powerblock model OPEJEQD. It has five wires. The white, black, Application caution - Power block models OPEJ5(QD) and OPEJE(QD) and yellow wires have no connection. Power block modules OPEJ5(QD) and OPEJE(QD) use "partial phase firing" power conversion to enable their wide NOTE: E Series OMNI-BEAM sensor heads may also be range of ac input voltage (24 to 250V ac). AC power is applied to the sensor for only a small portion of each ac halfused with standard OMNI-BEAM power blocks with solidcycle. The current demand during this period may be as high as 1 to 2 amps per sensor. state output relay. The collective current demand of several of these sensors on a common ac line is significant. If several sensors When E Series sensor heads are used with these power blocks, the power block Alarm output functions as a second load output that switches in parallel with the Load output (DPST). If the power block is a dc power block, neither output will have short-circuit or overload protection. E Series sensor heads do not have a D.A.T.A.TM display. are wired directly to the ac mains, it is unlikely that any adverse effects will be noticed. However, problems may be noticed if several sensors are connected to a common circuit that is isolated from the ac mains by a transformer. The collective peak current demand may rob other components on the same circuit of enough power to function properly. In the worst case, a transformer with inadequate reserve current capacity may overheat. Barring a transformer failure, the sensors themselves will operate normally. NOTE: Peak power demand is not an issue when these power blocks are powered from direct current (24 to 36V dc). Banner Engineering Corp. * Minneapolis, MN U.S.A www.bannerengineering.com * Tel: 763.544.3164 P/N 03540 rev. C 5 E Series OMNI-BEAMTM Sensors Overview, continued OMNI-BEAM Logic Modules E Series OMNI-BEAM sensors easily accept the addition of timing logic when needed. Three multiple-function logic modules are available. Model OLM5 is programmable for ON-delay, OFFdelay, or ON/OFF-delay timing logic. Models OLM8 and OLM8M1 offer either one-short or delayed one-shot functions. Programming of the logic function, the timing range, and the output state is done via a set of four switches located on the logic module. Both logic modules feature 15-turn clutched potentiometers for accurate timing adjustments. The logic module simply slides into the sensor head housing and interconnects without wires. Timing adjustments are easily accessible at the top of the sensor head and are protected by the sensor head's transparent, gasketed polycarbonate cover. Assembled sensors are rated NEMA 1, 2, 3, 3S, 4, 12, and 13. Plug-in timing logic modules are available for either delay or pulse timing functions. OMNI-BEAM Logic Module Specifications Operating Temperature: -40 to +70 C (-40 to +158 F) Timing Adjustments: Two 15-turn clutched potentiometers with brass elements, accessible from outside at top of sensor block, beneath gasketed cover. Timing Repeatability: Plus or minus 2% of timing range (maximum). Assumes conditions of constant temperature and power supply. Slide in Useful Time Range: Useful range is from maximum time down to 10% of maximum, all models. When timing potentiometer is set fully counterclockwise, time will be approximately 1% of maximum for models OLM5 and OLM8, and 2% of maximum for model OLM8M1. The logic module slides into the sensor head and interconnects without wires. Response Time: A disabled timing function adds no measurable sensing response time. OLM5 Delay Timer Logic Module Model OLM5 is programmable for ON-DELAY or OFFDELAY or ON/OFF DELAY timing functions. Each delay function may be independently adjusted and separately programmed for either a long or short adjustment range. NOTE 1: if both ranges of either delay function are selected (i.e., if both 1 second and 15 second switches are "on"), the delay time range becomes 16 seconds, maximum. NOTE 2: with switches #1 and #2 "off" (no ON-DELAY programmed), ON-DELAY is adjustable from "negligible" up to 100 milliseconds, maximum. Timing Logic Function and Timing Range #1 Switch Positions #2 #2 #4 ON-DELAY 1 second maximum ON OFF OFF OFF ON-DELAY 15 seconds maximum OFF ON OFF OFF OFF-DELAY 1 second maximum OFF OFF ON OFF OFF DELAY 15 seconds maximum OFF OFF OFF ON ON-DELAY OFF-DELAY 1 second maximum 1 second maximum ON OFF ON OFF ON-DELAY OFF-DELAY 1 second maximum 15 seconds maximum ON OFF OFF ON ON-DELAY OFF-DELAY 15 seconds maximum 1 second maximum OFF ON ON OFF ON-DELAY OFF-DELAY 15 seconds maximum 15 seconds maximum OFF ON OFF ON NOTE 3: with switches #3 and #4 "off" (no OFF-DELAY programmed), OFF-DELAY is adjustable from "negligible" up to 100 milliseconds, maximum. 6 P/N 03540 rev. C Banner Engineering Corp. * Minneapolis, MN U.S.A www.bannerengineering.com * Tel: 763.544.3164 E Series OMNI-BEAMTM Sensors Overview, continued OLM8 Pulse Timer Logic Module Models OLM8 and OLM8M1 are programmable for either a one-shot ("single-shot") pulse timer or a delayed one-shot logic timer. Delay and Pulse times may be independently adjusted and separately configured for either a long or short adjustment range. OLM8M1 maximum times are 1/10 those of the OLM8. NOTE 1: DELAY is non-retriggerable. Logic Function and Timing Ranges: models OLM8 and OLM8M1* Switch Positions #1 #2 #3 #4 ONE-SHOT 1 (.1) second max. pulse OFF OFF OFF ----- ONE-SHOT 15 (1.5) seconds max. pulse OFF OFF ON ----- DELAYED 1 (.1) second max. delay ONE-SHOT 1 (.1) second max. pulse ON OFF OFF ----- DELAYED 15 (1.5) seconds max. delay ONE-SHOT 1 (.1) second max. pulse OFF ON OFF ----- DELAYED 1 (.1) second max. delay ONE-SHOT 15 (1.5) seconds max. pulse ON OFF ON ----- DELAYED 15 (1.5) seconds max. delay ONE-SHOT 15 (1.5) second max. pulse OFF ON ON ----- For normally open outputs (outputs conduct during pulse time) _________ OFF PULSE is retriggerable if the DELAY time is less than the ONE-SHOT For normally closed outputs (outputs open during pulse time) __________ ON pulse time. *Timing specifications for model OLM8M1 are printed in (italics). NOTE 2: if both ranges of the delay function are selected (i.e., if both 1 second and 15 second switches are "on"), the delay time range becomes 16 (1.6*) seconds, maximum. NOTE 3: with switches #1 and #2 "off" (no DELAY programmed), DELAY is adjustable from "negligible" up to 10 (4.5*) milliseconds, maximum. Banner Engineering Corp. * Minneapolis, MN U.S.A www.bannerengineering.com * Tel: 763.544.3164 P/N 03540 rev. C 7 E Series OMNI-BEAMTM Sensors Configuration Light/Dark Operate Selection LIGHT/DARK switch LO DO Light- or dark-operate mode selection is done via a slide switch inside the bottom of the sensor head (see photo). To access the switch, first remove the transparent cover from the top of the sensor head, then unscrew the four captive assembly bolts that hold the sensor head to the power block. The switch is easily operated with a small screwdriver. Move the switch to the LEFT for LIGHT operate, or to the RIGHT for DARK operate (switch position information is inscribed on the printed circuit board, next to the switch). In LIGHT operate, the output is energized when the sensor "sees" light. In DARK operate, the output is energized when the sensor "sees" dark. Specifications Supply Voltage and Current 24 to 250V ac (50-60 Hz), or 24 to 36V dc at 45 mA dc maximum, exclusive of load. DC hookup is without regard to polarity. Output Configuration One internal form "C" (single-pole double-throw) relay Output Rating Maximum switching power (resistive load): 150 W, 600 VA Maximum switching voltage (resistive load): 250V ac or 30V dc Maximum switching current (resistive load): 5 A Minimum voltage and current: 5V dc, 0.1 A Mechanical life of relay: 10,000,000 operations Electrical life of relay at full resistive load: 100,000 operations Output Response Time 20 milliseconds ON and OFF; 100-millisecond delay on power-up (relay is de-energized during this period). Adjustments Multi-turn Gain control on top of sensor (beneath a transparent gasketed polycarbonate cover) allows precise sensitivity setting (turn clockwise to increase gain). Internal switch selects LIGHT operate or DARK operate. Optional logic module models OLM5, OLM8, and OLM8M1 have adjustable timing functions. Indicators Red LED indicators for Sense and Load on top of sensor (beneath a transparent gasketed polycarbonate cover). Sense LED lights when an object is sensed. Load LED lights when the output relay is energized. Timing Logic Optional logic modules are available: timing logic module OLM5 (DELAY timing logic) timing logic module OLM8 or OLM8M1 (PULSE timing logic) Construction Molded thermoplastic polyester housing. Power block is totally encapsulated. Molded acrylic lenses, stainless steel hardware. When assembled, all parts are fully gasketed. Assembled E Series OMNI-BEAM sensors are rated NEMA 1, 2, 3, 3S, 4, 12, and 13. Connections Sensors may be supplied either with 2-wire (for emitter models) and 5-wire (for all other models) 6' PVC-covered cable and 1/2'' NPS integral internal conduit thread in the sensor base, or integral "QD" (quick disconnect) connector. "QD" models use 5-conductor cord sets MBCC-5.. (sold separately). Operating Conditions Temperature: 0 to +50 C (+32 to +122 F). Temperature for Plastic Fiber Optics: -30 to +70 C (-20 to +158 F) Certifications (R) 8 P/N 03540 rev. C E71083 LR41887-17 Banner Engineering Corp. * Minneapolis, MN U.S.A www.bannerengineering.com * Tel: 763.544.3164 E Series OMNI-BEAMTM Sensors Dimensions Models OSEE, OSER, OSED, OSEDX, OSELV, OSELVAG*, OSECV** 54.6 mm (2.15") Model OSEFP Model OSEFX Transparent Cover (Gasketed) View: Power "ON" Light Moving Dot OUTPUT Indicator Remove to Access: NULL Adjustment SPAN Adjustment Lens Centerline Transparent Cover (gasketed) View: Sensing Status, Output Load Status Remove to Access: Sensitivity (Gain) Adjustment, Timing Adjustments 44.5 mm (1.75") 59.8 mm (2.35") 44.5 mm (1.75") #10 Screw Clearance (4) Cross-hole design for front, back, or side mounting 60.5 mm (2.38") 98.6 mm (3.88") 79.8 mm (3.14") Power Block 5.6 mm (0.22") 79.8 mm (3.14") 5.6 mm (0.22") Internal Thread (1/2-14NPSM) External Thread M30 X 1.5 7.1 mm (0.28") 98.6mm (3.88") 7.1 mm (0.28") #10 Screw Clearance (4) Cross-hole design for front, back, or side mounting 30.0 mm (1.18") 30.0 mm (1.18") 6.1 mm (0.24") dia 2 meter (6 ft) cable 2 m ( 6.5' Cable) * ** Depth of model OSELVAG is 57.7 mm (2.27'') Depth of model OSECV is 62.0 mm (2.44'') Quick-Disconnect Cordsets Style Model Length Dimensions 61 mm max. Mini-style 5-pin, straight connector MBCC-506 MBCC-512 MBCC-530 2m 4m 9m Pinout 7/8-16UN-2B o 28 mm max. 2 4 1 3 5 Key 1 = brown 2 = white 3 = blue 4 = black 5 = yellow Mini Straight 5-Pin Mini Banner Engineering Corp. * Minneapolis, MN U.S.A www.bannerengineering.com * Tel: 763.544.3164 P/N 03540 rev. C 9 E Series OMNI-BEAMTM Sensors WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any other warranty either expressed or implied. P/N 03540 rev. C Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 * Phone: 763.544.3164 * www.bannerengineering.com * Email: sensors@bannerengineering.com